2-895-959-12(1)
DVD Home Theatre
System
Operating Instructions
*
*DAV-HDX265/HDX267W only
DAV-HDX265/HDX266/HDX267W
©2007 Sony Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
11) Only use attachments/accessories specified by the
manufacturer.
Welcome!
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
Thank you for purchasing Sony DVD Home
Theatre System. Before operating this system,
please read this manual thoroughly and retain it
for future reference.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
This appliance is
classified as a CLASS 1
LASER product. This
marking is located on the
rear exterior.
Precautions
On power sources
• AC power cord (mains lead) must be changed only at
the qualified service shop.
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet (mains), even if the unit itself has been turned
off.
• Install this system so that the AC power cord (mains)
can be unplugged from the wall socket immediately
in the event of trouble.
GB
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
This System Can Play the Following
Discs .................................................7
Selecting [ORIGINAL] or [PLAY LIST]
on a DVD-R/DVD-RW.................. 41
Adjusting the Delay Between the Picture
and Sound....................................... 45
About MP3 Audio Tracks and JPEG
Image Files..................................... 46
Playing DATA CDs or DATA DVDs with
Files................................................ 48
Playing Audio Tracks and Images as a
Slide Show with Sound .................. 50
Enjoying DivX® Videos ...................... 52
(Except for United Kingdom and
North American models)
Step 1: Connecting the System and
TV..............................................10
Step 3: Performing the Quick
Setup ........................................15
Enjoying the Radio or Other
Components ............................28
Enjoying TV or VCR Sound from All
Speakers ..................................29
Selecting the Movie or Music
Playing VIDEO CDs with PBC Functions
(Ver.2.0) ......................................... 54
Mode.........................................29
Enjoying Surround Sound by Using Sound
Field................................................30
Controlling the TV with the Supplied
Remote ........................................... 58
Using the THEATRE SYNC
Searching for a Particular Point on
a Disc ..............................................32
(Scan, Slow-motion Play, Freeze
Frame)
Searching for a Title/Chapter/Track/
Scene, etc........................................33
Resuming Playback from the Point Where
You Stopped the Disc.....................34
Function.......................................... 58
Changing the Brightness of the Front
Panel Display.................................. 60
Using the DIGITAL MEDIA PORT
Adapter........................................... 61
GB
4
Download from Www.Somanuals.com. All Manuals Search And Download.
(CUSTOM PARENTAL
CONTROL)
Getting Optimal Surround Sound for a
Room ..............................................66
Calibrating the Appropriate Settings
Automatically .................................68
Setting the Display or Sound Track
Language ........................................72
(When letters/numbers appear in
the display)
GB
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1)MP3 (MPEG1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
2)Except for United Kingdom and North American
models.
About This Manual
• The instructions in this manual describe the
controls on the remote. You can also use the
controls on the unit if they have the same or
similar names as those on the remote.
• The instructions in this manual are for DAV-
HDX265, DAV-HDX266, and DAV-
HDX267W. DAV-HDX265 is the model used
for illustration purposes. Any difference in
operation is clearly indicated in the text, for
example, “DAV-HDX265 only.”
®
3) DivX is a video file compression technology,
developed by DivX, Inc.
4) DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under license.
• The Control Menu items may vary depending
on the area.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD+RWs/DVD+Rs, and
DVD-RWs/DVD-Rs.
• Measurements are expressed in feet (ft) for
North American models.
• The following symbols are used in this
manual.
Symbol
Meaning
Functions available for DVD
VIDEOs, DVD-Rs/DVD-RWs in
video mode, and DVD+Rs/
DVD+RWs
Functions available for DVD-Rs/
DVD-RWs in VR (Video
Recording) mode
Functions available for VIDEO
CDs (including Super VCDs or CD-
Rs/CD-RWs in video CD format or
Super VCD format)
Functions available for music CDs
or CD-Rs/CD-RWs in music CD
format
Functions available for DATA CDs
(CD-ROMs/CD-Rs/CD-RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)4)
video files
Functions available for DATA
DVDs (DVD-ROMs/DVD-Rs/
DVD-RWs/DVD+Rs/DVD+RWs)
containing MP31) audio tracks,
JPEG image files, and DivX2)3)4)
video files
GB
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The system can play DVD-ROMs/DVD+RWs/
DVD-RWs/DVD+Rs/DVD-Rs recorded in the
following formats:
This System Can Play the
Following Discs
– MP3 audio tracks, JPEG image files, and
DivX video files* of format conforming to
UDF (Universal Disc Format)
Format of
Disc logo
discs
* Except for United Kingdom and North American
models.
DVD VIDEO
Example of discs that the
system cannot play
DVD-RW/
DVD-R
The system cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than those
recorded in the formats listed on page 7
• CD-ROMs recorded in PHOTO CD format
• Data part of CD-Extras
DVD+RW/
DVD+R
• DVD Audios
• Super Audio CD
• DATA DVDs that do not contain MP3 audio
tracks, JPEG image files, or DivX video files*
* Except for United Kingdom and North American
models.
VIDEO CD
(Ver. 1.1 and
2.0 discs)/
• DVD-RAMs
Also, the system cannot play the following
discs:
• A DVD VIDEO with a different region code
Audio CD
CD-RW/CD-R
(audio data)
(MP3 files)
• A disc that has a non-standard shape (e.g.,
card, heart)
(JPEG files)
• A disc with paper or stickers on it
• A disc that has the adhesive of cellophane tape
or a sticker still left on it
Notes about CD-R/CD-RW/DVD-R/
DVD-RW/DVD+R/DVD+RW
“DVD-RW,” “DVD+RW,” “DVD+R,”
“DVD VIDEO,” and the “CD” logos are trademarks.
In some cases, CD-R/CD-RW/DVD-R/DVD-
RW/DVD+R/DVD+RW cannot be played on
this system due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
Note about CDs/DVDs
The system can play CD-ROMs/CD-Rs/CD-
RWs recorded in the following formats:
– audio CD format
The disc will not play if it has not been correctly
finalized. For more information, see the
operating instructions for the recording device.
Note that some playback functions may not
work with some DVD+RWs/DVD+Rs, even if
they have been correctly finalized. In this case,
– VIDEO CD format
– MP3 audio tracks, JPEG image files, and
DivX video files* of format conforming to
ISO 9660 Level 1/Level 2, or its extended
format, Joliet
continued
GB
7
Download from Www.Somanuals.com. All Manuals Search And Download.
view the disc by normal playback. Also some
DATA CDs/DATA DVDs created in Packet
Write format cannot be played.
If you try to play any other DVD VIDEO, the
message [Playback prohibited by area
limitations.] will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be given even though playing the
DVD VIDEO is prohibited by area restrictions.
Music discs encoded with
copyright protection
technologies
This product is designed to play back discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Note about playback
operations of DVDs and
VIDEO CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this system plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Be sure to read the
operating instructions supplied with the DVDs
or VIDEO CDs.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Copyrights
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
About Multi Session CD
• This system can play Multi Session CDs when
an MP3 audio track is contained in the first
session. Any subsequent MP3 audio tracks
recorded in later sessions can also be played
back.
• This system can play Multi Session CDs when
a JPEG image file is contained in the first
session. Any subsequent JPEG image files
recorded in later sessions can also be played
back.
• If audio tracks and images in music CD format
or video CD format are recorded in the first
session, only the first session will be played
back.
This system incorporates with Dolby* Digital
and Dolby Pro Logic (II) adaptive matrix
surround decoder and the DTS** Digital
Surround System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
**Manufactured under license from DTS, Inc.
“DTS” and “DTS Digital Surround” are registered
trademarks of DTS, Inc.
Region code
Your system has a region code printed on the
rear of the unit and will only play DVDs labeled
with the same region code.
ALL
DVD VIDEOs labeled
system.
will also play on this
GB
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started – BASIC –
Inserting batteries into the remote
You can control the system using the supplied remote. Insert two R6 (size AA) batteries by matching
the 3 and # ends on the batteries to the markings inside the compartment. To use the remote, point it
at the remote sensor on the unit.
Note
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Attaching the foot pads to the subwoofer
Attach the supplied foot pads to the bottom of the subwoofer to stabilize the subwoofer and prevent it
from slipping.
GB
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1: Connecting the System and TV
The following is the basic connection of the unit to the speakers and TV. For other TV connections, see
Refer to the connection diagram below, and read the additional information from 1 to 4 on the
following pages.
Front speaker (L)
Front speaker (R)
Center speaker
AM loop antenna (aerial)
DIR-TC1
AM
Y
P
B/CB
PR/CR
R
AUDIO IN
L
S
VIDEO
(DVD ONLY)
FM
75
(DVD ONLY)
COAXIAL
ANTENNA
TV/VIDEO
FRONT
R
FRONT
L
SUR
R
SUR
L
COMPONENT VIDEO OUT
VIDEO
SPEAKER
MONITOR OUT
OUT
DMPORT
(DVD ONLY)
CENTER
WOOFER
SPEAKER
AC power cord (mains lead)
B
A
FM wire antenna
(aerial)
VIDEO
IN
AUDIO
OUT
L
R
TV
Subwoofer
Surround speaker (L)
Surround speaker (R)
:Signal flow
GB
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• When you install the wireless kit WAHT-SD1 (supplied with DAV-HDX267W only) in the DIR-TC1 slot, you can
enjoy wireless performance. For details, see “Connecting Other Components” (page 24) and the operating
instructions of the WAHT-SD1.
1 Connecting the Speakers
Required cords
The connector and color tube of the speaker cords are the same color as the label of the jacks to be
connected.
Color tube
To the SPEAKER jack
(+)
(–)
Note
• Do not catch the speaker cord insulation in the SPEAKER jack.
To avoid short-circuiting the speakers
Short-circuiting of the speakers may damage the system. To prevent this, be sure to follow these
precautions when connecting the speakers. Make sure the bare wire of each speaker cord does not touch
another speaker terminal or the bare wire of another speaker cord, such as shown below.
Stripped speaker cord is touching
another speaker terminal.
Stripped cords are touching each other
due to excessive removal of insulation.
After connecting all the components, speakers, and AC power cord (mains lead), output a test tone to
check that all the speakers are connected correctly. For details on outputting a test tone, see page 77.
If no sound is heard from a speaker while outputting a test tone, or a test tone is output from a speaker
other than the one currently displayed on the Setup Display, the speaker may be short-circuited. If this
happens, check the speaker connection again.
Note
• Be sure to match the speaker cord to the appropriate terminal on the components: 3 to 3, and # to #. If the cords
are reversed, the sound will lack bass and may be distorted.
continued
GB
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Connecting the TV
Required cords
A Video cord
.
Yellow
B Audio cord (not supplied)
White (L/audio)
Red (R/audio)
Tip
• When you want to output the TV sound or stereo sound of a 2 channel source from the 6 speakers, select the “Dolby
3 Connecting the Antenna (Aerial)
To connect the AM loop antenna (aerial)
The shape and the length of the antenna (aerial) is designed to receive AM signals. Do not dismantle
or roll up the antenna (aerial).
1
2
Remove only the loop part from the plastic stand.
Set up the AM loop antenna (aerial).
3
Connect the cords to the AM antenna (aerial) terminals.
Cord (A) or cord (B) can be connected to either terminal.
A
Insert the cord pushing
down the terminal clamp.
B
Insert until this
part.
Note
• Do not place the AM loop antenna (aerial) near the unit or other AV equipment, as noise may result.
Tip
• Adjust the direction of the AM loop antenna (aerial) for best AM broadcast sound.
4
Make sure the AM loop antenna (aerial) is connected firmly by pulling softly.
GB
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To connect the FM wire antenna (aerial)
Connect the FM wire antenna (aerial) to the FM 75 Ω COAXIAL jack.
FM wire antenna (aerial)
(supplied)
FM wire antenna (aerial)
(supplied)
or
FM 75 Ω COAXIAL jack
FM 75 Ω COAXIAL jack
Note
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM
antenna (aerial) as shown below.
Unit
Outdoor FM antenna (aerial)
4 Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of this unit to a wall outlet (mains), connect the
speakers to the unit.
Changing the color system (PAL or NTSC)
(Asian, Australian, and Middle Eastern models only)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color
system.
The initial setting of the system for Australian and Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
To change the color system
1
2
Turn off the system by pressing "/1.
Turn on the system by pressing "/1 while pressing X on the unit.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front panel display when the color system is set to NTSC.
GB
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• When you change the positions of the speakers, it is
recommended that you change the settings. For
details, see “Getting Optimal Surround Sound for a
Step 2: Positioning the
System
Positioning the speakers
For the best possible surround sound, all the
speakers other than the subwoofer should be
placed at the same distance from the listening
position (A).
However, this system allows you to place the
center speaker up to 1.6 meters (5 ft) closer (B)
and the surround speakers up to 5.0 meters (16
ft) closer (C) to the listening position.
The front speakers can be placed from 1.0 to
7.0 meters (3 to 23 ft) (A) from the listening
position.
Place speakers as illustrated below.
Note
• Do not set the speakers in an inclined position.
• Do not place the speakers in locations that are:
– Extremely hot or cold
– Dusty or dirty
– Very humid
– Subject to vibrations
– Subject to direct sunlight
• When cleaning, use a soft cloth such as a cleaning
cloth for glasses.
• Do not use any type of abrasive pad, scouring
powder, or solvent such as alcohol or benzine.
GB
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE SETUP
OSD:
Step 3: Performing the
Quick Setup
ENGLISH
ENGLISH
FRENCH
MENU:
AUDIO:
SUBTITLE:
SPANISH
PORTUGUESE
Follow the steps below to make the minimum
number of basic adjustments for using the
system.
5
6
Press X/x to select a language.
"/1
The system displays the menu and subtitles
in the selected language.
Press
.
The Setup Display for selecting the aspect
ratio of the TV to be connected appears.
SCREEN SETUP
16:9
16:9
TV TYPE:
YCB
CR/RGB (HDMI):
C/X/x/c,
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
4:3 LETTER BOX
4:3 PAN SCAN
ON
DISPLAY
BLACK LEVEL (COMPONENT OUT):
4:3 OUTPUT:
OFF
FULL
1
2
Turn on the TV.
7
Press X/x to select the setting that
matches your TV type.
Press [/1.
x If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
[16:9] (page 72)
Note
• Disconnect the headphones when you perform
the Quick Setup. You cannot operate steps after
11 with the headphones connected.
• Make sure that the function is set to “DVD”
x If you have a 4:3 standard TV
[4:3 LETTER BOX] or [4:3 PAN SCAN]
3
4
Switch the input selector on your TV so
that the signal from the system
appears on the TV screen.
8
9
Press
.
The Setup Display for selecting the speaker
formation appears.
[Press [ENTER] to run QUICK SETUP.]
appears at the bottom of the TV screen. If
this message does not appear, recall the
again.
Press C/c to select the speaker
formation image as the speakers are
actually positioned.
For details, see “Getting Optimal Surround
Press
without inserting a disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
SPEAKER FORMATION
STANDARD
continued
GB
15
Download from Www.Somanuals.com. All Manuals Search And Download.
12
13
14
Press
.
Note
• When the wireless kit WAHT-SD1 (supplied
with DAV-HDX267W only) is installed,
[STANDARD (WIRELESS)] appears instead.
AUTO CALIBRATION
Connect calibration mic. Start
measurement?
10
11
Press
.
YES
NO
Connect the calibration mic to the
A.CAL MIC jack on the front panel and
press X/x to select [YES].
Set up the calibration mic at the ear level
using a tripod, etc. (not supplied). The front
of each speaker should face the calibration
mic, and there should be no obstruction
between the speakers and the calibration
mic. Be quiet during the measurement.
Auto Calibration starts.
Note
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the
volume down. Give consideration to children
and neighbor.
• Avoid being in the measurement area and
making noise during the measurement (which
takes about 3 minutes), as it may interfere with
measurement.
Unplug the calibration mic and press C/
c to select [YES].
AUDIO IN / A.CAL MIC
Calibration mic
Measurement complete.
FRONT L :
FRONT R :
CENTER
YES
YES
:
NONE
SUBWOOFER : YES
SURROUND L : NONE
SURROUND R : NONE
If OK, unplug calibration mic and select
“YES”.
YES
NO
Note
• The environment of the room in which the
system is installed may affect measurements.
• If measurement fails, follow the message then
retry [AUTO CALIBRATION].
• When you select [SECOND ROOM] for
[SPEAKER FORMATION], measurement of
[SURROUND L] and [SURROUND R] is not
displayed.
Press
.
Quick Setup is finished. All connections
and setup operations are complete.
To quit the Quick Setup
Press DISPLAY in any Step.
GB
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• If you change the position of the speakers, reset the
speaker settings. See “Getting Optimal Surround
• If you want to change any of the settings, see “Using
To recall the Quick Setup display
1 Press
stop mode.
The Control Menu display appears.
DISPLAY when the system is in
2 Press X/x to select [SETUP], then
press
The options for [SETUP] appear.
.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
0 : 0 0 : 0 2
QUICK
QUICK
CUSTOM
RESET
3 Press X/x to select [QUICK], then press
.
The Quick Setup display appears.
GB
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the demonstration
mode to on/off
Getting Started – ADVANCED –
1
2
Press SYSTEM MENU.
Turning off the
Demonstration
Press X/x repeatedly until “DEMO”
appears in the front panel display, then
press
or c.
3
Press X/x to select a setting.
"/1
The default setting is underlined.
• “DEMO ON”: sets the demonstration
mode to on.
• “DEMO OFF”: sets the demonstration
mode to off.
4
5
Press
.
SYSTEM
MENU
The setting is made.
Press SYSTEM MENU.
X/x/c,
The system menu turns off.
After connecting the AC power cord (mains
lead), the demonstration appears in the front
panel display. When you press "/1 on the
remote, the demonstration turns off.
Note
• When you press "/1 on the unit, the demonstration
does not turn off.
• When you set the demonstration mode in the system
menu to on, the demonstration does not turn off even
though you press "/1 on the remote. To turn off the
demonstration, set the demonstration mode to off,
then press "/1 on the remote. When the
demonstration mode is set to off, the system saves
power in standby mode.
• If the system is at its factory default settings (ex. after
off the demonstration simply by pressing "/1 on the
remote. Otherwise, to stop the demonstration, you
need to set “DEMO” to “DEMO OFF.”
GB
18
Download from Www.Somanuals.com. All Manuals Search And Download.
For the other speakers
Installing the Speakers on
a Wall
You can use the speakers by installing on the
wall.
6 to 9 mm
3
(1/4 to
/
inch)
Installing the speakers on a
wall
8
1
Prepare screws (not supplied) that are
suitable for the hole on the back of
each speaker. See the illustrations
below.
3
Hang the speakers on the screws.
4.6 mm
(3/16 inch)
10 mm
13
4 mm (5/32 inch)
(
/32 inch)
30 mm (1 3
/16 inches)
Hole on the back of
the speaker
4.6 mm
(3/16 inch)
10 mm
13
(
/32 inch)
Rear of speaker
Note
2
Fasten the screws to the wall.
• Use screws that are suitable for the wall material and
strength. As a plaster board wall is especially fragile,
attach the screws securely to a beam and fasten them
to the wall. Install the speakers on a vertical and flat
wall where reinforcement is applied.
For the center speaker
160 mm
(6 5
16 inches)
/
• Contact a screw shop or installer regarding the wall
material or screws to be used.
• Sony is not responsible for accident or damage
caused by improper installation, insufficient wall
strength or improper screw installation, natural
calamity, etc.
7 to 9 mm
3
(9/32 to
/
inch)
8
GB
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the TV (Advanced)
Sends the played back DVD image to the connected TV.
Check the jacks of your TV, and choose connection method A, B, C, or D. Picture quality improves
in order from A (standard) to D (HDMI).
TV with HDMI* IN jack
D
IN
To
S VIDEO
To HDMI* OUT
DIR-TC1
AM
Y
P
B/CB
PR/CR
R
AUDIO IN
L
S
VIDEO
(DVD ONLY)
FM
75
(DVLY)
COAXIAL
ANTENNA
TV/VIDEO
FRONT
R
FRONT
L
SUR
R
SUR
L
CMPONENVIDEO UT
VIDEO
SPEAKER
MOR OUT
OUT
DMORT
(DVD ONLY)
CENTER
WOOFER
SPEAKER
To COMPONENT
VIDEO OUT
To VIDEO
C
B
S
A
VIDEO
IN
VIDEO
IN
Y
PB/CB
PR/CR
TV with COMPONENT
VIDEO IN jacks
TV with VIDEO IN jack
:Signal flow
TV with S VIDEO IN jack
* HDMI (high-definition multimedia interface)
The system incorporates High-Definition Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
GB
20
Download from Www.Somanuals.com. All Manuals Search And Download.
A To connect to a TV with the VIDEO IN jack
Connect the video cord.
.
Yellow
B To connect to a TV with the S VIDEO IN jack
Connect an S video cord (not supplied). To use the S video jack instead of the video jack, your TV
monitor must also be connected via an S video jack. S video signals are on a separate bus from the video
signals and will not be output through the video jack.
C To connect to a TV with the COMPONENT VIDEO IN jacks
Connect a component video cord (not supplied). To use the COMPONENT VIDEO OUT jacks (Y, PB/
CB, PR/CR) instead of the video jack, your TV monitor must be equipped with via COMPONENT
VIDEO IN jacks (Y, PB/CB, PR/CR). If your TV accepts progressive format signals, you must use this
Green
Blue
Red
D To connect to a TV with the HDMI (high-definition multimedia
interface)/DVI (digital visual interface) IN jack
Use a certified HDMI (high-definition multimedia interface) cord (not supplied) to enjoy high quality
digital picture and sound through the HDMI OUT (high-definition multimedia interface out) jack.
To connect to a TV with DVI (digital visual interface) input
Use an HDMI (high-definition multimedia interface)-DVI (digital visual interface) converter cord (not
supplied) with an HDMI (high-definition multimedia interface)-DVI (digital visual interface) adaptor
(not supplied). The DVI (digital visual interface) jack will not accept any audio signals. Furthermore,
you cannot connect the HDMI OUT (high-definition multimedia interface out) jack to DVI (digital
visual interface) jacks that are not HDCP (high-bandwidth digital content protection) compliant (e.g.,
DVI (digital visual interface) jacks on the computer displays).
To select the type of video signal output from the HDMI OUT (high-
definition multimedia interface out) jack
When you connect the unit and the TV with the HDMI cord, selects the type of video signals output
from the HDMI OUT (high-definition multimedia interface out) jack.
For details, refer also to the operating instructions supplied with the TV/projector, etc.
1
Press FUNCTION repeatedly to select “DVD.”
continued
GB
21
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press VIDEO FORMAT.
The current type of video signals appears in the front panel display.
Each time you press VIDEO FORMAT, the display changes as follows:
t 720 × 480p*
r
1280 × 720p*
r
720 × 480p*
r
1920 × 1080i*
• “720 × 480p*”: Sends 720 × 480p video signals.**
• “1280 × 720p*”: Sends 1280 × 720p video signals.
• “1920 × 1080i*”: Sends 1920 × 1080i video signals.
*i: interlace, p: progressive
**Depending on the country, [720 × 576p] may appear.
Note
• When the HDMI indicator on the front panel lights up, images other than [720 × 480p] or [720 × 576p] are stretched
vertically.
When connecting to a standard 4:3 screen TV
Depending on the disc, the image may not fit your TV screen.
To change the aspect ratio, see page 72.
Does your TV accept progressive signals?
Progressive is the method for displaying TV images which reduces flickering, and sharpens the image.
To display using this method, you need to connect to a TV that accepts progressive signals.
FUNCTION
VIDEO
FORMAT
“PROGRE” lights up in the front panel display when the system outputs progressive signals.
1
Press FUNCTION repeatedly to select “DVD.”
GB
22
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press VIDEO FORMAT.
The current signal appears in the front panel display.
Each time you press VIDEO FORMAT, the display changes as follows:
t NORMAL (INTERLACE)
r
PROGRESSIVE
x NORMAL (INTERLACE)
Select this setting when:
– your TV does not accept progressive signals, or,
– your TV is connected to jacks other than the COMPONENT VIDEO OUT jacks (MONITOR
OUT (VIDEO/S VIDEO)).
x PROGRESSIVE
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT VIDEO OUT jacks.
Normally select this under the above condition. This automatically detects the software type, and
selects the appropriate conversion method.
Note that the picture will not be clear or no picture will appear if you select these settings when
either of the above conditions are not met.
Note
• When you connect the unit and the TV with the HDMI cord during the system is set to “NORMAL
(INTERLACE),” the system is set to “PROGRESSIVE” automatically.
Tip
• When you connect the unit and the TV with the HDMI cord, VIDEO FORMAT is used for selecting the type of
video signals output from the HDMI OUT jack. For details, see “To select the type of video signal output from the
About DVD software types and the conversion method
DVD software can be divided into 2 types: film-based software and video-based software.
Video-based software is derived from TV, such as dramas and sit-coms, and displays images at 30
frames/60 fields per second. Film-based software is derived from film and displays images at 24 frames
per second. Some DVD software contains both video and film.
In order for these images to appear natural on your screen when output in progressive format, the
progressive signals need to be converted to match the type of DVD software that you are watching.
Note
• When you play video-based software in progressive signal format, sections of some types of images may appear
unnatural due to the conversion process when output through the COMPONENT VIDEO OUT jacks. Even though
you set to “PROGRESSIVE,” images from the MONITOR OUT (VIDEO or S VIDEO) jack are unaffected as they
are output in the interlace format.
GB
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting Other Components
You can enjoy sound using the speakers of this system by connecting the AUDIO OUT jacks of another
component. For video connection of other components, connect directly to the TV.
DIR-TC1 slot for
the WAHT-SD1
Screws*
DIR-TC1
AM
Y
P
B/CB
PR/CR
R
AUDIO IN
L
S
VIDEO
(DVD ONLY)
FM
75
(DVD ONLY)
COAXIAL
ANTENNA
V/VIDE
FRONT
R
FRONT
L
SUR
R
SUR
L
COMPONENT VIDEO OUT
VIDEO
SPEAKER
MONITOR OUT
OUT
DMPORT
(DVD ONLY)
CENTER
WOOFER
SPEAKER
To TV/VIDEO
(AUDIO IN)
To DMPORT jack
DIGITAL MEDIA
PORT adapter
AUDIO
OUT
L
R
VCR, digital satellite receiver
or PlayStation, etc.
:Signal flow
*
CAUTION
Please do not remove the screws before installing the WAHT-SD1.
To connect the AUDIO OUT jacks of other components to the TV/VIDEO
(AUDIO IN) jacks of this unit
Connect the VCR or other components to the TV/VIDEO (AUDIO IN) jacks using the audio cord (not
supplied). When connecting a cord, be sure to match the color-coded sleeves to the appropriate jacks
on the components.
White (L/audio)
Red (R/audio)
To connect the DIGITAL MEDIA PORT adapter
Connect a DIGITAL MEDIA PORT adapter (not supplied) to the DMPORT jack. For details of the
GB
24
Download from Www.Somanuals.com. All Manuals Search And Download.
To listen to the portable audio source sound through the system
Connect the audio output jacks of the portable audio source to the AUDIO IN jack on the front panel
of the unit with the stereo mini-plug cord (not supplied).
Tip
• When listening to MP3 format recordings using a portable audio source, you can enhance the sound.
Press FUNCTION to select “AUDIO.” Connect the portable audio source. Press SOUND FIELD repeatedly until
“A.F.D. STD” appears in the front panel display.
To cancel, select other than “A.F.D. STD.”
Wireless system option
When you install the WAHT-SD1 (supplied with DAV-HDX267W only) in the DIR-TC1 slot, you can
enjoy wireless performance by transmission of the sound to the surround speakers. For details, see the
operating instructions of the WAHT-SD1.
Note
• Be sure to make connections securely to avoid hum and noise.
• When you connect another component with a volume control, turn up the volume of the other components to a level
where sound is not distorted.
GB
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press DISC 1-5.
Press the button of the disc number you
want.
Basic Operations
When no disc is in the disc stocker you
selected, “NO DISC” appears. Perform next
Step while “*DISC-1* (eg., 2-5)” flashes.
Playing Discs
5
6
Press A.
Load a disc.
Adjust the
volume
Place one disc on the tray, and then press A.
"/1
H FUNCTION
A
DISC 1-5/
indicators
Connect
headphones
Disc tray
Note
"/1
• When you play an 8 cm disc, place it on the
inner circle of the tray. Be careful that the disc is
not skewed on the inner circle of the tray.
• Do not forcibly press the disc tray closed with
your finger, as this may cause malfunction.
• Do not place more than one disc on the tray.
Z
DISC SKIP
FUNCTION
7
Press H.
The system starts playback (continuous
play).
To load other discs, press DISC 1-5 (that is
not loaded with a disc) and A and load the
disc.
MUTING
VOLUME +/–
./>
/
H
x
The system starts playback (continuous
play) of the disc whose DISC indicator is
green.
X
Depending on the DVD VIDEO or VIDEO CD,
some operations may be different or restricted.
Refer to the operating instructions supplied with
your disc.
To play back other discs, press DISC SKIP
on the remote or DISC 1-5 on the unit.
Adjust the volume on the unit.
The volume level appears on the TV screen
and in the front panel display.
1
2
Turn on your TV.
Switch the input selector on the TV to
this system.
Note
• Depending on the system status, the volume level
may not appear on the TV screen.
3
Press "/1.
The system turns on.
Unless the system is set to “DVD,” press
FUNCTION to select “DVD.”
• When you set the HDMI CONTROL function to on
(page 74), the TV that is connected to the system with
the HDMI cord can be synch-operated with the
system. For details, see the HDMI CONTROL Guide
(supplied separately).
GB
26
Download from Www.Somanuals.com. All Manuals Search And Download.
To
Press
Tip
• When you connect the system and TV with the HDMI
cord, you can operate them simply, using the HDMI
CONTROL function. For details, see the HDMI
CONTROL Guide (supplied separately).
Go back to the preceding
chapter, track, or scene
. (except for JPEG)
Turn off the sound
temporarily
MUTING. To cancel,
press it again or
VOLUME + to adjust
the sound volume.
• The DISC 1-5 indicators change color as follows:
– green: the disc is selected, or the disc is being
played back.
Change a disc while playing DISC SKIP
another disc
– off: there is no disc.
– orange: a disc is loaded in the disc stocker but not
selected.
Play the desired disc directly DISC 1-5 on the unit.
Stop play and remove the
desired disc
DISC 1-5 and A on the
unit or Z on the
remote.
– The indicator turns off if an unplayable disc is
inserted.
To save the power in standby
mode
Replay the previous scene*
(instant
replay) during
playback.
Press "/1 while the system turns on. To cancel
standby mode, press "/1 once.
Briefly fast forward the
current scene**
(instant
advance) during
playback.
To turn on/off the DISC 1-5
indicators’ illumination
* DVD VIDEOs/DVD-RWs/DVD-Rs only. The
button can be used except for DivX video files
(except for United Kingdom and North American
models).
When you do not operate the system for more
than 30 minutes, the illumination of the DISC 1-
5 indicators starts automatically. You can turn
the illumination on or off.
**DVD VIDEOs/DVD-RWs/DVD-Rs/DVD+RWs/
DVD+Rs only. The button can be used except for
DivX video files (except for United Kingdom and
North American models).
1 Press SYSTEM MENU.
2 Press X/x repeatedly until “ILLUM MODE”
appears in the front panel display, then
Note
press
or c.
• You may not be able to use the instant replay or
instant advance function with some scenes.
3 Press X/x to select a setting.
The default setting is underlined.
• “ILLUM ON”: sets the illumination mode
to on.
About DVD 5-DISC changer
The disc changer consists of a playing unit and a
stocker which transports the discs to the disc slot
and the playing unit.
For example, if you press DISC 3, the stocker
moves until the DISC 3 comes to the position of
the playing unit and then moves the DISC 3 over
the playing unit.
• “ILLUM OFF”: sets the illumination mode
to off.
4 Press
.
The setting is made.
5 Press SYSTEM MENU.
The system menu turns off.
Note
Additional operations
• Noise may come from the disc changer when
changing discs or turning the system on and off.
However, this is just noise produced by the operation
of the internal mechanisms and does not indicate a
malfunction.
To
Press
Stop
x
Pause
X
Resume play after pause
X or H
Go to the next chapter,
track, or scene
> (except for JPEG)
GB
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the input level of
the sound from connected
components
Enjoying the Radio or
Other Components
Distortion may occur when listening to a
component connected to the TV/VIDEO jacks
on the rear panel or to the AUDIO IN jack on the
front panel. This is not a malfunction and will
depend on the component connected.
FUNCTION
To prevent this, you can change the input level
from the sound of the other components.
1
Press FUNCTION repeatedly until “TV/
VIDEO” or “AUDIO” appears in the
front panel display.
SYSTEM
MENU
X/x/c,
2
3
Press SYSTEM MENU.
Press X/x repeatedly until
“ATTENUATE” appears in the front
panel display, then press
or c.
4
Press X/x to select a setting.
The default setting is underlined.
• “ATT ON”: attenuates the input level.
The output level is changed.
Selecting the connected
component
• “ATT OFF”: normal input level.
You can use a VCR or other components
connected to the TV/VIDEO jacks on the rear
panel. Refer to the operating instructions
supplied with the components for further
information.
5
6
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
Press FUNCTION repeatedly until “TV/
VIDEO” appears in the front panel display.
Each time you press FUNCTION, the mode of
the system changes in the following sequence.
DVD t TUNER FM t TUNER AM t
TV/VIDEO t DMPORT t AUDIO t …
GB
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoying TV or VCR Sound
from All Speakers
Selecting the Movie or
Music Mode
You can enjoy TV or VCR sound from all the
speakers in this system.
You can choose a suitable sound mode for
movies or music.
For details, see “Step 1: Connecting the System
MOVIE/
MUSIC
FUNCTION
SOUND
FIELD
Press MOVIE/MUSIC during playback.
Press MOVIE/MUSIC repeatedly until the
mode you want lights up in the front panel
display. The default setting is underlined.
• AUTO: selects the mode automatically to
produce the sound effect depending on the
disc.
1
2
Press FUNCTION repeatedly until “TV/
VIDEO” appears in the front panel
display.
Press SOUND FIELD repeatedly until
the sound field you want appears in the
front panel display.
• MOVIE: provides the sound for movies.
• MUSIC: provides the sound for music.
Tip
When you want to output the TV sound or
stereo sound of a 2 channel source from the
6 speakers, select the “PRO LOGIC,” “PLII
MOVIE,” or “PLII MUSIC” sound field.
• When the movie or music mode is selected,
“MOVIE” or “MUSIC” is displayed in the front panel
display. When neither “MOVIE” or “MUSIC” is
displayed in the front panel display, “AUTO” is
selected.
Note
Note
• You cannot operate these setup items when you
connect headphones to the unit.
• When you set the [HDMI CONTROL] setting in
Audio Control function is activated and no sound
may be output from the TV. For details of the System
Audio Control function, see the HDMI CONTROL
Guide (supplied separately).
GB
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic outputting of the
original sound
Sound Adjustments
x AUTO FORMAT DIRECT STANDARD
The auto decoding function automatically
detects the type of audio signal being input
(Dolby Digital, DTS, or standard 2 channel
stereo) and performs the proper decoding if
necessary. This mode presents the sound as it
was recorded/encoded, without adding any
effects (e.g. reverberation).
Enjoying Surround Sound
by Using Sound Field
You can take advantage of surround sound
simply by selecting one of the system’s pre-
programmed sound fields. They bring exciting
and powerful sound of movie theaters into your
home.
However, if there are no low frequency signals
(Dolby Digital LFE, etc.), it will generate a low
frequency signal for output to the subwoofer.
Outputting the sound from
multiple speakers
SOUND
FIELD
x AUTO FORMAT DIRECT MULTI
This mode lets you enjoy audio playback of all
types of discs from multiple speakers.
Note
• The sound is not output from multiple speakers
depending on the source.
Outputting 2 channel sources
like CDs by 5.1channel
Press SOUND FIELD.
x Dolby Pro Logic
Press SOUND FIELD repeatedly until the sound
field you want appears in the front panel display.
Dolby Pro Logic produces five output channels
from 2 channel sources. This mode performs Pro
Logic decoding to the input signal and output to
front, center, and surround speakers.
Meanwhile, the surround channel becomes
monaural.
All sound field
Sound field
Display
AUTO FORMAT DIRECT A.F.D. STD
STANDARD
x Dolby Pro Logic II MOVIE/MUSIC
Dolby Pro Logic II produces five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
AUTO FORMAT DIRECT A.F.D. MULTI
MULTI
Dolby Pro Logic
PRO LOGIC
Dolby Pro Logic II MOVIE PLII MOVIE
Dolby Pro Logic II MUSIC PLII MUSIC
2 CHANNEL STEREO
2CH STEREO
HP 2CH
Note
HEADPHONE
• When the input signal is multi channel source, Dolby
Pro Logic and Dolby Pro Logic II MOVIE/MUSIC
are canceled and the multi channel source is output
directly.
2 CHANNEL STEREO
HEADPHONE VIRTUAL
HP VIRTUAL
GB
30
Download from Www.Somanuals.com. All Manuals Search And Download.
• When the bilingual broadcast sound is input, Dolby
Pro Logic and Dolby Pro Logic II MOVIE/MUSIC
are not effective.
Using only the front speaker
and subwoofer
x 2 CHANNEL STEREO
This mode outputs the sound from the front left
and right speakers and subwoofer. Standard 2
channel (stereo) sources completely bypass the
sound field processing. Multi channel surround
formats are downmixed to two channels.
This allows you to play any source using only
the front left and right speakers and subwoofer.
Enjoying the surround sound
by headphones
x HEADPHONE 2 CHANNEL STEREO
This mode outputs the sound from headphone L/
R. Standard 2 channel (stereo) sources
completely bypass the sound field processing.
Multi channel surround formats are downmixed
to two channels.
x HEADPHONE VIRTUAL
This mode outputs the sound as surround from
headphone L/R. This mode is effective only
when a multi channel source is played.
To turn the surround effect off
Press SOUND FIELD repeatedly until “A.F.D.
STD” or “2CH STEREO” appears in the front
panel display.
GB
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Opposite direction
×2b t 1m t 2m t 3m
Various Functions for Playing Discs
Searching for a Particular
Point on a Disc
3m (DVD VIDEO/DVD-VR mode/DivX video*/
VIDEO CD only)
×2b (DVD VIDEO only)
(Scan, Slow-motion Play, Freeze
Frame)
* Except for United Kingdom and North American
models.
With each press, playback speed becomes faster.
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
Watching frame by frame
(Slow-motion Play)
(DVD VIDEO, DVD-R, DVD-RW, DivX
video*, VIDEO CD only)
Note
• Depending on the DVD/DivX video*/VIDEO CD,
you may not be able to do some of the operations
described.
* Except for United Kingdom and North American
models.
Press /m or M/ when the system is in
pause mode. To return to normal playback
speed, press H. Each time you press /m or
M/ during Slow-motion Play, the playback
speed changes. Two speeds are available. With
each press the indication changes as follows:
* Except for United Kingdom and North American
models.
Locating a point quickly by
playing a disc in fast forward
or fast reverse (Scan)
(Except for JPEG)
Playback direction
2
y 1
Opposite direction (DVD VIDEO only)
y 1
Press /m or M/ while playing a disc.
When you find the point you want, press H to
2
return to normal speed. Each time you press
m or M/ during scan, the playback speed
changes. With each press the indication changes
as shown below. Actual speeds may differ with
some discs.
/
Playing one frame at a time
(Freeze Frame)
(DVD VIDEO, DVD-R, DVD-RW, DivX
video*, VIDEO CD only)
Playback direction
* Except for United Kingdom and North American
models.
×2B t 1M t 2M t 3M
When the system is in the pause mode, press
(step) to go to the next frame. Press
(step) to go to the preceding frame
(DVD VIDEO/DVD-R/DVD-RW only). To
return to normal playback, press H.
3M (DVD VIDEO/DVD-VR mode/DivX video*/
VIDEO CD only)
×2B (DVD VIDEO/CD only)
* Except for United Kingdom and North American
models.
Note
• You cannot search for a still picture on a DVD-R/
DVD-RW in VR mode.
• For DATA CDs/DATA DVDs, this function works
only for DivX video files (except for United
Kingdom and North American models).
GB
32
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press
.
[** (**)] changes to [– – (**)].
Searching for a Title/
Chapter/Track/Scene,
etc.
(
(
)
)
1 2 2 7
3 4
1 : 3 2 : 5 5
DVD VIDEO
T
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, or scene. As titles
and tracks are assigned unique numbers on the
disc, you can select the desired one by entering
its number. Or, you can search for a scene using
the time code.
4
5
Press X/x or the number buttons to
select the title, chapter, track, index,
scene, etc., number you want to search
for.
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
1
Press
DATA CD/DATA DVD with JPEG image
files, press DISPLAY twice.)
DISPLAY. (When playing a
Press
.
The Control Menu display appears.
The system starts playback from the
selected number.
2
Press X/x to select the search method.
The display will show different items
depending on the disc.
To search for a scene using the
time code (DVD VIDEO and
DVD-VR mode only)
[TITLE], [TRACK], [SCENE]
[CHAPTER], [INDEX]
[TIME/TEXT]
1 In Step 2, select
[TIME/TEXT].
[T **:**:**] (playing time of the current title)
is selected.
Select [TIME/TEXT] to search for a
starting point by inputting the time code.
2 Press
.
[TRACK]
[ALBUM]
[FILE]
[T **:**:**] changes to [T --:--:--].
3 Input the time code using the number
buttons, then press
.
For example, to find the scene at 2 hours, 10
minutes, and 20 seconds after the beginning,
just enter [2:10:20].
Example: when you select
[CHAPTER]
[** (**)] is selected (** refers to a number).
The number in parentheses indicates the
total number of titles, chapters, tracks,
indexes, scenes, albums or files.
Tip
• When the Control Menu display is turned off, you can
search for a chapter (DVD VIDEO/DVD-R/DVD-
RW), track (VIDEO CD/CD), or file* (DATA CD/
DATA DVD (DivX video)) by pressing the number
(
(
)
)
1 2 2 7
1 8 3 4
buttons and
.
DVD VIDEO
T
1 : 3 2 : 5 5
* Except for United Kingdom and North American
models.
Note
• You cannot search for a scene on a DVD+RW using
the time code.
Selected row
GB
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Searching by Scene
(Picture Navigation)
Resuming Playback from
the Point Where You
Stopped the Disc
(Resume Play)
You can divide the TV screen into 9 subscreens
and find the desired scene quickly.
1
2
3
Press PICTURE NAVI during playback.
The following display appears.
When you stop the disc, the system remembers
the point where you pressed x and “RESUME”
appears in the front panel display. As long as
you do not remove the disc, Resume Play will
work even if the system enters standby mode by
pressing "/1.
ENTER
CHAPTER VIEWER
Press PICTURE NAVI repeatedly to
select an item.
1
While playing a disc, press x to stop
playback.
• [TITLE VIEWER] (DVD VIDEO only)
• [CHAPTER VIEWER] (DVD VIDEO
only)
“RESUME” appears in the front panel
display.
If “RESUME” does not appear, Resume
Play is not available.
• [TRACK VIEWER] (VIDEO CD/
Super VCD only)
2
Press H.
Press
.
The system starts playback from the point
where you stopped the disc in Step 1.
The first scene of each title, chapter, or
track appears as follows.
Note
• Depending on where you stop the disc, the system
may not resume playback from exactly the same
point.
1
4
7
2
5
8
3
6
9
• The point where you stopped playing may be cleared
when:
– you eject the disc.
– the system enters standby mode (DATA CD/
DATA DVD only).
– you change or reset the settings on the Setup
Display.
4
Press C/X/x/c to select a title, chapter,
or track, and press
.
– you change the parental control level.
– you change the function by pressing FUNCTION.
– you disconnect the AC power cord (mains lead).
• For DVD-Rs/DVD-RWs in VR mode, VIDEO CDs,
CDs, DATA CDs, and DATA DVDs, the system
remembers the resume playback point for the current
disc.
The system starts playback from the
selected scene.
To return to normal play during
setting
Press O RETURN.
• The resume point is cleared when you select another
disc.
Note
• Depending on the disc, you may not be able to select
some items.
• Resume Play does not work during Program Play and
Shuffle Play.
• This function may not work properly with some
discs.
GB
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
Creating Your Own
Program
To enjoy a disc that is played
before by resume playback
(Multi-disc Resume)
(Program Play)
(DVD VIDEO, VIDEO CD only)
You can play the contents of a disc in the order
you want by arranging the order of the tracks on
the disc to create your own program. You can
program up to 99 tracks.
This system stores the point where you stopped
the disc for up to 40 discs and resumes playback
the next time you insert the same disc. If you
store a resume playback point for the 41st disc,
the resume playback point for the first disc is
deleted.
To activate this function, set [MULTI-DISC
RESUME] in [CUSTOM SETUP] to [ON]. For
details, see “[MULTI-DISC RESUME] (DVD
Note
• You can program the track on the current disc only.
1
2
Press
DISPLAY.
The Control Menu display appears.
Press X/x to select
[PROGRAM], then press
.
The options for [PROGRAM] appear.
Tip
• To play from the beginning of the disc, press x twice,
then press H.
6 (14)
2 : 5 0
CD
T
Note
OFF
OFF
SET
ON
• If [MULTI-DISC RESUME] in [CUSTOM SETUP]
when you change the function by pressing
FUNCTION.
3
Press X/x to select [SET t], then
press
.
[TRACK] is displayed when you play a
VIDEO CD or CD.
PROGRAM
0:00:00
T
ALL CLEAR
1. TRACK
– –
– –
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
01
02
03
04
05
06
– –
– –
– –
– –
– –
Tracks recorded
on a disc
Total time of the
programmed tracks
continued
GB
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Press c.
To change or cancel a program
The cursor moves to the track row [T] (in
this case, [01]).
2 Select the program number of the track you
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
0:00:00
T
want to change or cancel using X/x.
– –
– –
01
02
03
04
05
06
If you want to delete the track from the
program, press CLEAR.
– –
– –
– –
– –
– –
– –
3 Follow Step 5 for new programming.
To cancel a program, select [--] under [T],
then press
.
Select the track you want to program.
For example, select track [02].
To cancel all of the tracks in the
programmed order
Press X/x to select [02] under [T], then
press
.
2 Press X and select [ALL CLEAR].
Selected track
3 Press
.
0:15:30
T
PROGRAM
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
– –
01
02
03
04
05
06
0 2
– –
– –
– –
– –
– –
– –
Total time of the programmed tracks
6
7
To program other tracks, repeat steps 4
to 5.
The programmed tracks are displayed in the
selected order.
Press H to start Program Play.
Program Play starts.
When the program ends, you can restart the
same program again by pressing H.
To return to normal play
In Step 3, press CLEAR or select [OFF]. To play
the same program again, select [ON] in Step 3
and press
.
To turn off the Control Menu
display
Press
DISPLAY repeatedly until the Control
Menu display is turned off.
GB
36
Download from Www.Somanuals.com. All Manuals Search And Download.
To return to normal play
Playing in Random Order
In Step 3, press CLEAR or select [OFF].
(Shuffle Play)
To turn off the Control Menu
display
Press
DISPLAY repeatedly until the Control
You can have the system “shuffle” tracks.
Subsequent “shuffling” may produce a different
playing order.
Menu display is turned off.
Note
• You cannot use this function with VIDEO CDs and
Super VCDs with PBC playback.
Note
• Same song may be played repeatedly during MP3
playback.
• You can shuffle the tracks on the current disc only.
1
2
Press
The Control Menu display appears.
Press X/x to select [SHUFFLE],
then press
The options for [SHUFFLE] appear.
DISPLAY during playback.
.
6 (14)
2 : 5 0
CD
T
OFF
OFF
TRACK
3
Press X/x to select the item to be
shuffled.
x When playing a VIDEO CD or CD
• [TRACK]: shuffles tracks on the disc.
x When Program Play is activated
• [ON]: shuffles tracks selected in Program
Play.
x When playing a DATA CD (except for
DivX*) or DATA DVD (except for DivX*)
• [ON (MP3)]: shuffles MP3 audio tracks in
the album on the current disc. When no
album is selected, the first album will play
in random order.
* Except for United Kingdom and North
American models.
Note
• A track already played is also selected in
random order.
4
Press
.
Shuffle Play starts.
GB
37
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a DATA CD or DATA
DVD
• [OFF]: does not play repeatedly.
Playing Repeatedly
(Repeat Play)
• [ALL DISCS]: repeats all of the discs.
• [ONE DISC]: repeats all of the albums on
the current disc.
• [ALBUM]: repeats the current album.
• [TRACK] (MP3 audio tracks only):
repeats the current track.
You can play all the titles, tracks or albums on a
disc or a single title, chapter, track, or album
repeatedly.
You can use a combination of Shuffle or
Program Play modes.
• [FILE] (DivX video files only): repeats
the current file.*
* Except for United Kingdom and North
American models.
1
2
Press
The Control Menu display appears.
Press X/x to select [REPEAT],
then press
The options for [REPEAT] appear.
DISPLAY during playback.
4
Press
.
The item is selected.
.
To return to normal play
In Step 3, press CLEAR or select [OFF].
6 (14)
2 : 5 0
CD
To turn off the Control Menu
display
T
Press
DISPLAY repeatedly until the Control
OFF
OFF
ALL DISCS
ONE DISC
TRACK
Menu display is turned off.
Note
• You cannot use this function with VIDEO CDs and
Super VCDs with PBC playback.
• When playing a DATA CD/DATA DVD which
contains MP3 audio track and JPEG image files, and
their playing time is not the same, the audio sound
will not match the image.
3
Press X/x to select the item to be
repeated.
The default setting is underlined.
x When playing a DVD VIDEO or DVD-
VR
• When [MODE (MP3, JPEG)] is set to [IMAGE
• [OFF]: does not play repeatedly.
• [ALL DISCS]: repeats all of the discs.
• [ONE DISC]: repeats all of the titles on
the current disc. (When playing a DVD-
VR, [ONE DISC] repeats all of the titles
of the selected type.)
• [TITLE]: repeats the current title on a
disc.
• [CHAPTER]: repeats the current chapter.
x When playing a VIDEO CD or CD
• [OFF]: does not play repeatedly.
• [ALL DISCS]: repeats all of the discs.
• [ONE DISC]: repeats all of the tracks on
the current disc.
• [TRACK]: repeats the current track.
GB
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the DVD’s Menu
Changing the Sound
A DVD is divided into a lot of sections, which
make up a picture or music feature. These
sections are called “titles.” When you play a
DVD which contains several titles, you can
select the title you want using DVD TOP
MENU.
When you play DVDs that allow you to select
items such as the language for the subtitles and
the language for the sound, select these items
using DVD MENU.
When playing a DVD VIDEO or DATA CD/
DATA DVD (DivX video files*) recorded in
multiple audio formats (PCM, Dolby Digital,
MPEG audio, or DTS), you can change the
audio format. If the DVD VIDEO is recorded
with multilingual tracks, you can also change the
language.
With VIDEO CDs, CDs, DATA CDs, or DATA
DVDs, you can select the sound from the right or
left channel and listen to the sound of the
selected channel through both the right and left
speakers.
1
Press DVD TOP MENU or DVD MENU.
The disc’s menu appears on the TV screen.
The contents of the menu vary from disc to
disc.
* Except for United Kingdom and North American
models.
2
3
Press C/X/x/c or the number buttons to
select the item you want to play or
change.
1
Press AUDIO during playback.
The following display appears.
Press
.
:
1
ENGLISH DOLBY DIGITAL 3/2.1
2
Press AUDIO repeatedly to select the
desired audio signal.
x When playing a DVD VIDEO
Depending on the DVD VIDEO, the choice
of language varies.
When four digits are displayed, they
indicate a language code. Refer to
which language the code represents. When
the same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
continued
GB
39
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a DVD-VR
The types of sound tracks recorded on a disc
are displayed. The default setting is
underlined.
Note
• While playing a Super VCD on which the audio track
2 is not recorded, no sound will come out when you
select [2:STEREO], [2:1/L], or [2:2/R].
Example:
• [1: MAIN] (main sound)
• [1: SUB] (sub sound)
• [1: MAIN+SUB] (main and sub sound)
• [2: MAIN]
Checking the audio signal
format
(DVD, DivX video* only)
* Except for United Kingdom and North American
models.
• [2: SUB]
• [2: MAIN+SUB]
If you press AUDIO repeatedly during
playback, the format of the current audio signal
(PCM, Dolby Digital, DTS, etc.) appears as
shown below.
Note
• [2: MAIN], [2: SUB], and [2: MAIN+SUB] do
not appear when one audio stream is recorded on
the disc.
x When playing a DVD
x When playing a VIDEO CD, CD, DATA
CD (MP3 audio), or DATA DVD (MP3
audio)
Example:
Dolby Digital 5.1 ch
The default setting is underlined.
• [STEREO]: the standard stereo sound
• [1/L]: the sound of the left channel
(monaural)
LFE (Low
Frequency Effect)
Surround (L/R)
:
• [2/R]: the sound of the right channel
(monaural)
3 / 2 .1
ENGLISH DOLBY DIGITAL
1
L
C
R
Front (L/R) +
Center
x When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
(except for United Kingdom and North
American models)
LFE
LS
RS
Currently playing
program format
The choice of DATA CD or DATA DVD
audio signal formats differ, depending on
the DivX video file contained on the disc.
The format is shown in the display.
Example:
Dolby Digital 3 ch
Surround
(Monaural)
x When playing a Super VCD
The default setting is underlined.
• [1:STEREO]: the stereo sound of the
audio track 1
Front (L/R)
:
2 / 1
2 SPANISH DOLBY DIGITAL
• [1:1/L]: the sound of the left channel of
the audio track 1 (monaural)
L
R
• [1:2/R]: the sound of the right channel of
the audio track 1 (monaural)
S
Currently playing
program format
• [2:STEREO]: the stereo sound of the
audio track 2
• [2:1/L]: the sound of the left channel of
the audio track 2 (monaural)
• [2:2/R]: the sound of the right channel of
the audio track 2 (monaural)
GB
40
Download from Www.Somanuals.com. All Manuals Search And Download.
x When playing a DATA CD (DivX video) or
DATA DVD (DivX video) (except for United
Kingdom and North American models)
Selecting [ORIGINAL] or
[PLAY LIST] on a DVD-R/
DVD-RW
Example:
MP3 audio
1: MP3 128k
Some DVD-Rs/DVD-RWs in VR (Video
Recording) mode have two types of titles for
playback: originally recorded titles
([ORIGINAL]) and titles that can be created on
recordable DVD players for editing ([PLAY
LIST]). You can select the type of title to be
played.
Bit rate
About audio signals
Audio signals recorded in a disc contain the
sound elements (channels) shown below. Each
channel is output from a separate speaker.
• Front (L)
1
Press
in stop mode.
DISPLAY when the system is
• Front (R)
The Control Menu display appears.
• Center
2
Press X/x to select
PLAY LIST], then press
[ORIGINAL/
.
• Surround (L)
• Surround (R)
The options for [ORIGINAL/PLAY LIST]
appear.
• Surround (Monaural): This signal can be either
the Dolby Surround Sound processed signals
or the Dolby Digital sound’s monaural
Surround audio signals.
(
3
)
1
T
4 4
(
)
2 8
1 : 3 0 : 5 0
DVD-VR
• LFE (Low Frequency Effect) signal
PLAY LIST
PLAY LIST
ORIGINAL
3
4
Press X/x to select a setting.
The default setting is underlined.
• [PLAY LIST]: plays the titles created
from [ORIGINAL] for editing.
• [ORIGINAL]: plays the titles originally
recorded.
Press
.
GB
41
Download from Www.Somanuals.com. All Manuals Search And Download.
When playing a VIDEO CD
ViewingInformationAbout
the Disc
(without PBC functions) or CD
1 Playing time of the current track
2 Remaining time of the current track
3 Playing time of the disc
4 Remaining time of the disc
5 Disc name
6 Track and index*
* VIDEO CD only.
Viewing the playing time and
remaining time in the front
panel display
When playing a DATA CD (MP3
audio) or DATA DVD (MP3 audio)
You can check disc information, such as the
remaining time, total number of titles in a DVD,
tracks in a VIDEO CD, CD, MP3, or file name
of a DivX video* using the front panel display
1 Playing time and current track number
2 Track (file) name
Tip
• When playing VIDEO CDs with PBC functions, the
playing time is displayed.
* Except for United Kingdom and North American
Note
models.
• The system can only display the first level of the
DVD/CD text, such as the disc name or title.
• If an MP3 file name cannot be displayed, “*” will
appear in the front panel display instead.
• The disc name or track name may not be displayed
depending on the text.
Press DISPLAY.
Each time you press DISPLAY while playing
the disc, the display changes 1 t 2 t ...
t 1 t ...
Some displayed items may disappear after a few
• Playing time of MP3 audio tracks and DivX video
files* may not be displayed correctly.
* Except for United Kingdom and North American
models.
seconds.
When playing a DVD VIDEO or
DVD-R/DVD-RW
1 Playing time and number of the current title
2 Remaining time of the current title
3 Playing time and number of the current
chapter
Checking the playing time and
remaining time
4 Remaining time of the current chapter
5 Disc name
6 Title and chapter
You can check the playing time and remaining
time of the current title, chapter, or track, and the
total playing time or remaining time of the disc.
You can also check the DVD text and MP3
folder name/file name recorded in the disc.
When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
(Except for United Kingdom and
North American models)
1
Press DISPLAY during playback.
The following display appears.
1 Playing time of the current file
2 Current file name
T
1:01:57
3 Current album and file number
Time information
GB
42
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press DISPLAY repeatedly to change
the time information.
Checking the play information
of the disc
The display and the kinds of time that you
can check depend on the disc you are
playing.
To check DVD/CD text
Press DISPLAY repeatedly in Step 2 to display
text recorded in the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the text.
If the disc does not contain text, “NO TEXT”
appears.
x When playing a DVD VIDEO or DVD-
RW
• T **:**:**
Playing time of the current title
• T–**:**:**
Remaining time of the current title
• C **:**:**
Playing time of the current chapter
• C–**:**:**
Remaining time of the current chapter
BRAHMS SYMPHONY
x When playing a VIDEO CD (with PBC
functions)
To check DATA CD/DATA DVD
• **:**
(MP3 audio/DivX video*) text
Playing time of the current scene
By pressing DISPLAY while playing MP3
audio tracks on a DATA CD/DATA DVD or
DivX video files* on a DATA CD/DATA DVD,
you can display the name of the album/track/file,
and the audio bit rate (the amount of data per
second of the current audio) on your TV screen.
x When playing a VIDEO CD (without
PBC functions) or CD
• T **:**
Playing time of the current track
• T–**:**
Remaining time of the current track
Bit rate**
• D **:**
Playing time of the current disc
• D–**:**
T
17:30 128k
Remaining time of the current disc
x When playing a DATA CD (MP3
audio) or DATA DVD (MP3 audio)
• T **:**
Playing time of the current track
JAZZ
RIVER SIDE
x When playing a DATA CD (DivX
video) or DATA DVD (DivX video)
(Except for United Kingdom and North
American models)
Album name
Track/file* name
* Except for United Kingdom and North American
models.
• **:**:**
**Appears when:
Playing time of the current file
– playing an MP3 audio track on DATA CDs/DATA
DVDs.
Note
• Characters/marks may not be displayed for some
languages.
– playing a DivX video file that contains MP3 audio
signals on DATA CDs/DATA DVDs (except for
United Kingdom and North American models).
• Depending on the type of disc being played, the
system can only display a limited number of
characters. Also, depending on the disc, not all text
characters will be displayed.
continued
GB
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the date
information
Changing the Angles
(JPEG only)
You can check the date information during
playback when the Exif* tag is recorded in the
JPEG image data.
If various angles (multi-angles) for a scene are
recorded on a DVD VIDEO, you can change the
viewing angle.
Press
DISPLAY twice during playback.
Press ANGLE during playback.
The Control Menu display appears.
Each time you press ANGLE, the angle changes.
(
(
)
1
1
8
Note
)
2 0
DATA CD JPEG
• Depending on the DVD VIDEO, you may not be able
to change the angle even if multi-angles are recorded
on the DVD VIDEO.
01/ 31/ 2007
Date information
* “Exchangeable Image File Format” is a digital
camera image format defined by the Japan
Electronics and Information Technology Industries
Association (JEITA).
Tip
• Date information is [MM/DD/YYYY].
MM: Month
DD: Day
YYYY: Year
• Date information varies depending on the area.
GB
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying the Subtitles
Adjusting the Delay
Between the Picture and
Sound
*
*
* Except for United Kingdom and North American
models.
(A/V SYNC)
If subtitles are recorded on a disc, you can turn
the subtitles on or off while playing. If
multilingual subtitles are recorded on the disc,
you can change the subtitle language while
playing, or turn the subtitles on or off whenever
you want.
*
*
* Except for United Kingdom and North American
models.
When the sound does not match the pictures on
the TV screen, you can adjust the delay between
the picture and sound.
Press SUBTITLE during playback.
Each time you press SUBTITLE, the subtitle
language changes.
1
2
Press
The Control Menu display appears.
Press X/x to select [A/V SYNC],
then press
The options for [A/V SYNC] appear.
DISPLAY.
Note
• Depending on the DVD VIDEO, you may not be able
to change the subtitles even if multilingual subtitles
are recorded on it. You also may not be able to turn
them off.
.
(
(
)
)
1
1
T
1 2
2 8
• You can change the subtitles if the DivX video file
has an “.AVI” or “.DIVX” extension and contains
subtitle information within the same file (except for
United Kingdom and North American models).
DVD VIDEO
0 : 0 0 : 0 2
OFF
OFF
ON
3
Press X/x to select a setting.
The default setting is underlined.
• [OFF]: does not adjust.
• [ON]: adjusts the difference between
picture and sound.
4
Press
.
Note
• Depending on the input stream, this function may not
be effective.
GB
45
Download from Www.Somanuals.com. All Manuals Search And Download.
MP3 audio track or JPEG
image file that the system can
play
About MP3 Audio Tracks
and JPEG Image Files
You can play the MP3 audio tracks or JPEG
image files:
• which have the extension “.MP3” (MP3 audio
track) or “.JPG”/“.JPEG” (JPEG image file)
What is MP3/JPEG?
• which conform to the DCF* image file format
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by Japan
Electronics and Information Technology Industries
Association (JEITA).
MP3 is audio compression technology that
satisfies the ISO/MPEG regulations. JPEG is
image compression technology.
Discs that the system can
play
Note
• The system will play any data with the
extension “.MP3,” “.JPG,” or “.JPEG” even if
they are not in MP3 or JPEG format. Playing
this data may generate a loud noise which
could damage your speaker system.
• The system does not conform to audio in
MP3PRO format.
You can play back DATA CDs (CD-ROMs/CD-
Rs/CD-RWs) or DATA DVDs (DVD-Rs/DVD-
RWs/DVD+Rs/DVD+RWs/DVD-ROMs)
recorded in MP3 (MPEG1 Audio Layer 3) or
JPEG format. However, the DATA CDs must be
recorded according to ISO 9660 Level 1, Level
2 or Joliet format and DATA DVDs of Universal
Disk Format (UDF) for the system to recognize
the tracks (or files). You can also play discs
recorded in Multi Session.
See the operating instructions supplied with the
CD-R/CD-RW or DVD-R/DVD-RW drives and
the recording software (not supplied) for details
on the recording format.
About the Multi-Session disc
If MP3 audio tracks or JPEG image files are
recorded in the first session, the system will also
play MP3 audio tracks or JPEG image files in
other sessions. If audio tracks and images in
audio CD format or video CD format are
recorded in the first session, only the first
session will be played back.
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
GB
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
Playback order of MP3 audio
tracks or JPEG image files
• If you add numbers (01, 02, 03, etc.) to the front of the
track (or file) names when you store the tracks (or
files) in a disc, the tracks (or files) will be played in
that order.
The playback order of MP3 audio tracks or
JPEG image files recorded on a DATA CD or
DATA DVD is as follows:
• A disc with many trees takes longer to start playback.
Note
x Structure of disc contents
• Playback order may differ from the illustration
depending on the software you use to create the
DATA CD or DATA DVD, or if there are more than
200 albums and 300 files in each album.
• The system can recognize up to 200 albums, and will
not play any albums beyond the 200th.
• The system may take longer time to playback, when
progressing to the following album or jump to other
album.
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
• Some type of JPEG files cannot be played.
Track (MP3 audio) or
File (JPEG image)
Album
When you insert a DATA CD or DATA DVD
and press H, the numbered tracks (or files) are
played sequentially, from 1 through 7. Any
sub-albums/tracks (or files) contained within a
currently selected album take priority over the
next album in the same tree. (Example: C
contains D so 4 is played before 5.)
When you press DVD MENU and the list of
names are arranged in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
GB
47
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop playback
Playing DATA CDs or
DATA DVDs with MP3
Audio Tracks and JPEG
Image Files
Press x.
To play the next or previous MP3
audio track
Press ./>. Note that you can select the
next album by continuing to press > after the
last track on the current album, but that you
cannot return to the previous album by pressing
.. To return to the previous album, select the
album from the album list.
Selecting an MP3 audio track
or album
To return to the previous display
Press O RETURN.
1
Load a DATA CD or DATA DVD.
To turn off the display
The albums recorded on the DATA CD or
DATA DVD appear. When an album is
being played, its title is shaded.
Press DVD MENU.
Selecting a JPEG image file or
album
(
)
3
3 0
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
1
Load a DATA CD or DATA DVD.
The albums recorded on the DATA CD or
DATA DVD appear. When an album is
being played, its title is shaded.
J A Z Z
C L A S S I C
S A L S A O F C U B A
B O S S A N O V A
(
)
3
3 0
2
Press X/x to select an album.
R O C K B E S T H I T
K A R A O K E
M Y F A V O U R I T E S O N G
R & B
J A Z Z
C L A S S I C
S A L S A O F C U B A
B O S S A N O V A
x When selecting an album
Press H to start playing the selected
album.
x When selecting a track
Press
.
The list of tracks contained in the album
appears.
M Y F A V O U R I T E S O N G
(
)
1
2 5 6
W A L T Z F O R D E B B Y
M Y R O M A N C E
M I L E S T O N E S
M Y F U N N Y V A L E N T I N E
A U T U M N L E A V E S
A L L B L U E S
S O M E D A Y M Y P R I N C E W...
Press X/x to select a track and press
.
The selected track starts playing. You can
turn the track list off by pressing DVD
MENU. Pressing DVD MENU again will
display the album list.
GB
48
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Press X/x to select an album.
To rotate a JPEG image
When a JPEG image file is displayed on the TV
screen, you can rotate the image by 90 degrees.
Press X/x while viewing an image. Each time
you press X, the image rotates counterclockwise
by 90 degrees.
x When selecting an album
Press H to start playing the selected
album.
x When selecting an image
Press PICTURE NAVI.
Images of files in the album appear in 16
subscreens.
Example of when you press X once:
Rotating direction
1
2
3
4
5
6
7
8
9
10
14
11
15
12
16
13
Press C/X/x/c to select the image you want
to view and press
Press CLEAR to return to normal view.
.
To stop playback
Press x.
Tip
• A scroll box is displayed at the right side of the TV
screen. To display the additional image files, select
the bottom image and press x. To return to the
previous image, select the top image and press X.
To play the next or previous JPEG
image file
Press C/c when the Control Menu display is not
displayed. Note that you can select the next
album by continuing to press c after the last
image on the current album, but that you cannot
return to the previous album by pressing C. To
return to the previous album, select the album
from the album list.
GB
49
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Press X/x to select the album you want
and press H.
Playing Audio Tracks and
Images as a Slide Show
with Sound
The system starts playing the selected
album.
You can turn the album list on and off by
pressing DVD MENU repeatedly.
Tip
• When you select [AUTO], the system can recognize
up to 300 MP3 tracks and 300 JPEG files in a single
album. When you select [AUDIO (MP3)] or [IMAGE
(JPEG)], the system can recognize up to 600 MP3 or
600 JPEG files in a single album. A maximum of 200
albums can be recognized regardless of the selected
mode.
You can play a slide show with sound by first
placing both MP3 and JPEG files in the same
album on a DATA CD or DATA DVD. When
you play back the DATA CD or DATA DVD,
select [AUTO] mode as explained below.
1
2
Load a DATA CD or DATA DVD.
Press DISPLAY when the system is
Note
• If you set [MODE (MP3, JPEG)] to [IMAGE
(JPEG)] on a disc that contains MP3 tracks only or
[AUDIO (MP3)] on a disc that contains JPEG files
only, you may not be able to change the [MODE
(MP3, JPEG)] setting.
in stop mode.
The Control Menu display appears.
3
Press X/x to select
(MP3, JPEG)], then press
[MODE
.
• PICTURE NAVI does not work when [AUDIO
(MP3)] is selected.
The options for [MODE (MP3, JPEG)]
appear.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound still
skips, then reduce the size of the JPEG file.
(
)
)
1 2 2 7
(
1 8 3 4
DATA CD MP3
T
1 : 3 2 : 5 5
AUTO
AUTO
AUDIO (MP3)
IMAGE (JPEG)
Specifying the slide show
duration
(JPEG only)
When you play JPEG image files using slide
show, you can specify the duration for slides to
appear on the TV screen.
4
Press X/x to select a setting.
The default setting is underlined.
• [AUTO]: plays both the JPEG image files
and MP3 audio tracks in the same album
as a slide show.
1
2
Press
DISPLAY twice.
The Control Menu display appears.
• [AUDIO (MP3)]: plays only MP3 audio
tracks continuously.
Press X/x to select
[INTERVAL], then press
.
• [IMAGE (JPEG)]: plays only JPEG
image files as a slide show.
The options for [INTERVAL] appear.
3 ( 12)
5
6
Press
.
1(
4)
DATA CD JPEG
1 0 / 2 9 / 2 0 0 7
NORMAL
NORMAL
FAST
SLOW1
SLOW2
Press DVD MENU.
The list of albums recorded on the DATA
CD or DATA DVD appears.
GB
50
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press X/x to select a setting.
3
4
Press X/x to select a setting.
The default setting is underlined.
• [NORMAL]: sets the duration to about 6
to 9 seconds.
• [FAST]: sets the duration shorter than
[NORMAL].
The default setting is underlined.
• [MODE1]: The image sweeps in from top
to bottom.
• [MODE2]: The image stretches out from
left to right of the TV screen.
• [MODE3]: The image stretches out from
the center of the TV screen.
• [SLOW1]: sets the duration longer than
[NORMAL].
• [SLOW2]: sets the duration longer than
[SLOW1].
• [MODE4]: The images randomly cycle
through the effects.
• [MODE5]: The next image slides over the
previous image.
4
Press
.
Note
• [OFF]: turns off this function.
• Some JPEG files may take longer to display than
others, which may make the duration seems longer
than the option you selected. Especially progressive
JPEG files or JPEG files of 3,000,000 pixels or more.
Press
.
Selecting an effect for image
files in the slide show
(JPEG only)
When you play a JPEG image file, you can
select the effect to be used when viewing the
slide show.
1
2
Press
The Control Menu display appears.
Press X/x to select [EFFECT],
then press
DISPLAY twice.
.
The options for [EFFECT] appear.
3 ( 12)
1(
4)
DATA CD JPEG
1 0 / 2 3 / 2 0 0 7
MODE1
MODE1
MODE2
MODE3
MODE4
MODE5
OFF
GB
51
Download from Www.Somanuals.com. All Manuals Search And Download.
DivX video files that the system
can play
®
Enjoying DivX Videos
The system can play data that is recorded in
DivX format, and which has the extension
“.AVI,” or “.DIVX.” The system will not play
files with the extension “.AVI” or “.DIVX” if
they do not contain a DivX video.
(Except for United Kingdom and North
American models)
About DivX Video Files
Tip
• For details about playable MP3 audio tracks or JPEG
image files on DATA CDs or DATA DVDs, see
®
DivX is a video file compression technology,
developed by DivX, Inc. This product is an
®
official DivX Certified product.
Note
You can play DATA CDs and DATA DVDs that
• The system may not play a DivX video file when the
file has been combined from two or more DivX video
files.
®
contain DivX video files.
DATA CDs and DATA DVDs that
the system can play
• The system cannot play a DivX video file of size
more than 720 (width) x 576 (height) or 2GB.
• Depending on the DivX video file, sound may skip or
not match the pictures on the TV screen.
• The system cannot play some DivX video files that
are longer than 3 hours.
Playback of DATA CDs (CD-ROMs/CD-Rs/
CD-RWs) and DATA DVDs (DVD-ROMs/
DVD-Rs/DVD-RWs/DVD+Rs/DVD+RWs) on
this system is subject to certain conditions:
• Depending on the DivX video file, the picture may
pause or be unclear. In which case, it is recommended
that you create the file at a lower bit rate. If the sound
is still noisy, MP3 is the recommended audio format.
Note, however, this system does not conform to
WMA (Windows Media Audio) format.
• Because of the compression technology used for
DivX video files, it may take some time after you
press H for the picture to appear.
– With DATA CDs/DATA DVDs that contain
DivX video files in addition to MP3 audio
tracks or JPEG image files, the system plays
only the DivX video files.
However, this system only plays DATA CDs
whose logical format is ISO 9660 Level 1/Level
2 or Joliet, and DATA DVDs of Universal Disk
Format (UDF).
Refer to the operating instructions supplied with
the disc drives and the recording software (not
supplied) for details on the recording format.
Selecting an album
1
Press DVD MENU.
A list of albums on the disc appears. Only
albums that contain DivX video files are
listed.
About playback order of data on
DATA CDs or DATA DVDs
JPEG image files” (page 47). Note that the
playback order may not be applicable,
(
)
3
3
depending on the software used for creating the
DivX video file, or if there are more than 200
albums and 600 DivX video files in each album.
S U M M E R 2 0 0 3
N E W Y E A R ' S D A Y
M Y F A V O U R I T E S
Note
• The system may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
2
Press X/x to select the album you want
to play.
GB
52
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Press H.
To play the next or previous DivX
video file without turning on the
above file list
The system starts playing the selected
album.
To select DivX video files, see “Selecting a
You can select the next or previous DivX video
file in the same album by pressing ./>.
You can also select the first file of the next
album by pressing > during playback of the
last file of the current album. Note that you
cannot return to the previous album by pressing
.. To return to the previous album, select it
from the album list.
To go to the next or previous
page
Press C/c.
To turn off the display
Press DVD MENU repeatedly.
Tip
To stop playback
• If the number of viewing times is preset, you can play
the DivX video files as many times as the preset
number. The following occurrences are counted:
Press x.
– when the system is turned off.
– when another file is played.
– when the disc tray is opened.
Selecting a DivX video file
1
press
.
The list of files in the album appears.
M Y F A V O U R I T E S
(
)
1
2
H A W A I I 2 0 0 4
V E N U S
2
Press X/x to select a file and press
.
The selected file starts playing.
To go to the next or previous
page
Press C/c.
To return to the previous display
Press O RETURN.
To stop playback
Press x.
GB
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing VIDEO CDs with
PBC Functions (Ver.2.0)
(PBC Playback)
With PBC (Playback Control) functions, you
can enjoy simple interactive operations, search
functions, and other such operations.
PBC playback allows you to play VIDEO CDs
interactively by following the menu on the TV
screen.
1
Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
2
Select the item number you want by the
number buttons.
3
4
Press
.
Follow the instructions in the menu for
interactive operations.
Refer to the operating instructions supplied
with the disc, as the operating procedure
may differ depending on the VIDEO CD.
To go back to the menu
Press O RETURN.
Note
• Depending on the VIDEO CD, [Press ENTER] in
Step 3 may appear as [Press SELECT] in the
operating instructions supplied with the disc. In this
case, press H.
Tip
• To play without using PBC, press ./> or the
number buttons while the system is in stop mode to
select a track, then press H or
. The system starts
continuous play. You cannot play still pictures such
as a menu. To return to PBC playback, press x twice,
then press H.
GB
54
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the preset number
Restart from Step 1.
Tuner Functions
To change the AM tuning interval
(except for Russian and Middle
Eastern models)
Presetting Radio Stations
You can preset 20 FM stations, and 10 AM
stations. Before tuning, make sure to turn down
the volume to minimum.
The AM tuning interval can be set to either
10 kHz or 9 kHz.
To change the AM tuning interval, first tune in
any AM station, then turn off the system by
pressing "/1 on the unit. While holding down
> on the unit, press "/1 on the unit to turn on
the power. If you change the interval, AM preset
stations will be erased.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
2
Press and hold TUNING + or – until the
auto scanning starts.
To reset the interval, repeat the same procedure.
Scanning stops when the system tunes in a
station. “TUNED” and “ST” (for stereo
program) appear in the front panel display.
3
4
Press SYSTEM MENU.
Press X/x repeatedly until “MEMORY”
appears in the front panel display.
5
Press
or c.
A preset number appears in the front panel
display.
6
Press X/x to select the preset number
you want.
Tip
• You can select the preset number directly by
pressing the number buttons.
7
Press
.
The station is stored.
8
9
Repeat Steps 1 to 7 to store other
stations.
Press SYSTEM MENU.
The system menu turns off.
GB
55
Download from Www.Somanuals.com. All Manuals Search And Download.
If an FM program is noisy
Listening to the Radio
If an FM program is noisy, you can select
monaural reception. There will be no stereo
effect, but reception will improve.
Preset radio stations in the system’s memory
1 Press SYSTEM MENU.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
2 Press X/x repeatedly until “FM MODE”
appears in the front panel display.
The last received station is tuned in.
2
Press PRESET + or – repeatedly to
select the preset station.
3 Press
or c.
Each time you press the button, the system
tunes in one preset station.
4 Press X/x to select “MONO.”
The default setting is underlined.
• “STEREO”: stereo reception.
• “MONO”: monaural reception.
Tip
• You can select the preset station number directly
by pressing the number buttons.
5 Press
The setting is made.
.
3
Adjust the volume by pressing
VOLUME +/–.
6 Press SYSTEM MENU.
The system menu turns off.
To turn off the radio
Press "/1.
To listen to non-preset radio
stations
Naming preset stations
You can enter a name for preset stations. These
names (for example, “XYZ”) appear in the front
panel display when a station is selected.
Note that no more than one name can be entered
for each preset station.
Use manual or automatic tuning in Step 2.
For manual tuning, press TUNING + or –
repeatedly.
For automatic tuning, press and hold TUNING +
or –. The automatic tuning stops automatically
when the system receives the radio station. To
stop the automatic tuning manually, press
TUNING + or –.
1
Press FUNCTION repeatedly until
“TUNER FM” or “TUNER AM” appears
in the front panel display.
The last received station is tuned in.
To listen to radio stations when
you know the frequencies
2
Press PRESET + or – repeatedly to
select the preset station you want to
create an index name for.
Use direct tuning in Step 2.
1 Press D.TUNING.
3
4
Press SYSTEM MENU.
2 Press the number buttons to select the
Press X/x repeatedly until “NAME IN”
appears in the front panel display.
frequencies.
3 Press
.
Tip
• To improve reception, reorient the supplied antennas
(aerials).
5
Press
or c.
GB
56
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
Create a name by using the cursor
buttons.
Press X/x to select a character, then press c
to move the cursor to the next position.
Letters, numbers, and other symbols can be
input for a radio station.
If you make a mistake
Press C/c repeatedly until the character to
be changed flashes, then press X/x to select
the desired character.
To erase the character, press C/c
repeatedly until the character to be erased
flashes, then press CLEAR.
Press
.
“COMPLETE” appears in the front panel
display, and the station name is stored.
8
Press SYSTEM MENU.
The system menu turns off.
Tip
• You can check the frequency by pressing DISPLAY
Viewing the station name or
frequency in the front panel
display
When the system is set to “TUNER FM” or
“TUNER AM,” you can check the frequency
using the front panel display.
Press DISPLAY.
Each time you press DISPLAY, the display
changes as shown.
1 Station name*
2 Frequency**
* This is displayed if you have entered a name for a
preset station.
**Returns to the original display when several seconds
has elapsed.
GB
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the THEATRE SYNC
Function
Other Operations
Controlling the TV with the
Supplied Remote
THEATRE SYNC allows you to turn on your
Sony TV and this system, changes the system
mode to “DVD,” and then switches the TV’s
input source you set with one button push.
You can control your TV (Sony only) with the
supplied remote.
Preparing for the THEATRE
SYNC function
Controlling TVs with the
remote
Register the TV’s input source connected to this
system.
You can control the TV by using following
buttons.
Press and hold TV INPUT while entering the
code for the TV’s input source connected
to this unit (see the table) using the number
buttons.
By pressing
TV [/1
You can
Turn the TV on or off.
TV INPUT
Switch the TV’s input source
between the TV and other input
sources.
The TV’s input source is selected.
Set your TV’s input to the input you used to
connect the unit. For details, see the operating
instructions of your TV.
TV VOL +/–
TV CH +/–
Adjust the TV volume.
Select the TV channel.
Select the TV channel.
Number
buttons*,
ENTER*
By pressing Number
TV’s input source
TV INPUT
0
No input source
(Default)
DVD MENU*
C/X/x/c*,
Display the menu of the TV.
Select the item on the menu.
1
VIDEO1
*
2
VIDEO2
RETURN*
Return to the previous channel or
layer on the menu of the TV.
3
VIDEO3
4
VIDEO4
5
VIDEO5
* Use these buttons while pressing the TV button.
6
VIDEO6
- is for selecting a channel number greater than
10. (For example, for channel 25, press -, then
2 and 5.)
7
VIDEO7
8
VIDEO8
9*
COMPONENT 1
COMPONENT 2
COMPONENT 3
CLEAR*
Note
• Depending on the TV, you may not be able to control
your TV or to use some of the buttons above.
SYSTEM
MENU*
PICTURE
NAVI*
COMPONENT 4
* Except for North American models.
GB
58
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatingtheTHEATRESYNC
function
Using the Sound Effect
Point the remote to the direction of TV and this
unit, then press THEATRE SYNC once.
Reinforcing bass frequencies
You can reinforce bass frequencies.
If this function does not work, change the
transmit time. The transmit time varies
depending on the TV.
Press DYNAMIC BASS.
Bass frequencies are effectively reinforced.
To change the transmit time
To turn off the sound effect
Press and hold TV CH + while entering the
code for transmit time (see the table) using
the number buttons.
Press DYNAMIC BASS again.
The transmit time from the remote is selected.
By pressing Number
Transmit time
TV CH +
1
2
3
4
5
6
7
8
0.5 (Default)
1
1.5
2
3
4
5
6
Note
• This function is only for Sony TVs. (This function
may not work on some Sony TVs.)
• If distance between TV and this unit is too far, this
function may not work. Install the unit near the TV.
• Keep the remote pointed in the direction of the TV
and this unit while entering the code.
GB
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Sleep Timer
Changing the Brightness
of the Front Panel Display
You can set the system to turn off at a preset
time, so you can fall asleep listening to music.
You can preset the time in 1 or 10-minutes
increments.
The brightness of the front panel display can be
set to either of 2 levels.
1
2
Press SYSTEM MENU.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “SLEEP”
appears in the front panel display, then
Press X/x repeatedly until “DIMMER”
appears in the front panel display, then
press
or c.
press
or c.
3
Press X/x to select a setting.
3
Press X/x to select the brightness of
the front panel display.
The minutes display (the remaining time)
changes as follows:
The default setting is underlined.
• “DIMMER OFF”: Bright.
SLEEP 90M y SLEEP 80M y SLEEP 70M
Y
Y
• “DIMMER ON”: The front panel display
and the Sony logo become dark.
SLEEP OFF y SLEEP 10M ..... SLEEP 60M
4
5
Press
.
Tip
• You can select the remaining time by pressing
the number buttons. In this case, you can preset
the time in 1-minute increments.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
4
5
Press
.
The setting is made and “SLEEP” lights up
in the front panel display.
Press SYSTEM MENU.
The system menu turns off.
To change the remaining time
Restart from Step 1.
To cancel the Sleep Timer
function
Select “SLEEP OFF” in Step 3.
GB
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• Depending on the type of DIGITAL MEDIA PORT
adapter (not supplied), you may be able to operate a
connected component using either the buttons on the
remote or the unit. The following illustration shows
an example of buttons that can be used in this case.
Using the DIGITAL MEDIA
PORT Adapter
The DIGITAL MEDIA PORT (DMPORT)
adapter is for enjoying sound from a portable
audio source or computer. By connecting a
DIGITAL MEDIA PORT adapter, you can
enjoy sound from the connected component on
the system.
Available DIGITAL MEDIA PORT adapters
vary in each area.
For details on connecting the DIGITAL MEDIA
PORT adapter, see “Connecting Other
Note
• Do not connect an adaptor other than the DIGITAL
MEDIA PORT adapter.
./>
H
• Do not connect or disconnect the DIGITAL MEDIA
PORT adapter to/from the unit while the system is
turned on.
x
X
• Depending on the type of DIGITAL MEDIA PORT
adapter (not supplied), the images are also output. In
this case, the system outputs the composite video
signal only regardless of the type of video signal.
Playing the connected
component on the system
1
Press FUNCTION repeatedly until
“DMPORT” appears in the front panel
display.
2
Start playback of the connected
component.
The sound and images from the connected
component are played on the system or
connected TV.
For operation details, see the operating
instructions of the DIGITAL MEDIA
PORT adapter (not supplied).
Tip
• When listening to MP3 or other compressed music
using a portable audio source, you can enhance the
sound. Press SOUND FIELD repeatedly until
“A.F.D. STD” appears in the front panel display. To
cancel, select other than “A.F.D. STD.”
GB
61
Download from Www.Somanuals.com. All Manuals Search And Download.
To insert a disc while the child
lock function is on
Deactivating the Buttons
on the Unit
Press Z on the remote to open the disc tray and
press DISC SKIP repeatedly until the desired
DISC indicator (1-5) lights up, then place a disc
on the tray and press Z on the remote.
(Child Lock)
You can deactivate the buttons on the unit
(except for "/1) for preventing misoperation,
such as child mischief (child lock function).
When the child lock function is activated, the
buttons on the unit are locked and “
up in the front panel display. (You can operate
the system by using the remote.)
” lights
Note
• When you operate the buttons on the unit while the
child lock function is on, “CHILD LOCK” appears in
the front panel display.
1
2
Press SYSTEM MENU.
Press X/x repeatedly until “CHILD
LOCK” appears in the front panel
display, then press
or c.
3
Press X/x to select a setting.
The default setting is underlined.
• “OFF”: Child lock function off.
• “ON”: Child lock function on.
4
5
Tip
Press
.
The setting is made.
Press SYSTEM MENU.
The system menu turns off.
• You can activate the child lock function by pressing
x for more than 5 seconds (“
” lights up in the
front panel display).
To cancel, press x for more than 5 seconds so that
” disappears from the front panel display.
“
To remove a disc while the child
lock function is on
Press Z on the remote and press DISC SKIP
repeatedly until the desired DISC indicator (1-5)
lights up.
GB
62
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Press X/x to select [ON t], then press
.
Advanced Settings and Adjustments
x If you have not entered a password
The display for registering a new password
appears.
Locking Discs
(CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL)
PARENTAL CONTROL
Enter a new 4-digit password,
ENTER
You can set two kinds of playback restrictions
for the desired disc.
then press
.
• Custom Parental Control
You can set playback restrictions so that the
system will not play inappropriate discs.
• Parental Control
Enter a 4-digit password using the number
buttons, then press
.
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Custom
Parental Control and Parental Control.
The display for confirming the password
appears.
x When you have already registered a
password
The display for entering the password
appears.
Preventing playback of
specific discs [CUSTOM
PARENTAL CONTROL]
PARENTAL CONTROL
Enter password, then press ENTER
.
You can set the same Custom Parental Control
password for up to 40 discs. When you set the
41st-disc, the first disc is canceled.
1
2
3
Insert the disc you want to lock.
5
Enter or re-enter your 4-digit password
using the number buttons, then press
.
If the disc is playing, press x to stop
playback.
Press
DISPLAY while the system is
[Custom parental control is set.] appears
and the TV screen returns to the Control
Menu display.
in stop mode.
The Control Menu display appears.
Press X/x to select
[PARENTAL CONTROL], then press
To turn off the Custom Parental
Control function
.
The options for [PARENTAL CONTROL]
appear.
(
)
)
1 2 2 7
2 Press X/x to select [OFF t], then press
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
.
3 Enter your 4-digit password using the
number buttons, then press
.
OFF
ON
PLAYER
PASSWORD
continued
GB
63
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
Press X/x to select
[PARENTAL CONTROL], then press
To play a disc for which Custom
Parental Control is set
.
1 Insert the disc for which Custom Parental
The options for [PARENTAL CONTROL]
appear.
Control is set.
The [CUSTOM PARENTAL CONTROL]
display appears.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
CUSTOM PARENTAL CONTROL
Custom parental control is already
OFF
ON
PLAYER
PASSWORD
set. To play, enter your password
ENTER
and press
.
Press X/x to select [PLAYER t], then
press
.
2 Enter your 4-digit password using the
number buttons, then press
The system is ready for playback.
x If you have not entered a password
The display for registering a new password
appears.
.
Tip
• If you forget your password, enter the 6-digit number
“199703” using the number buttons when the
[CUSTOM PARENTAL CONTROL] display asks
PARENTAL CONTROL
Enter a new 4-digit password,
you for your password, then press
will ask you to enter a new 4-digit password.
. The display
ENTER
then press
.
Limiting playback for children
[PARENTAL CONTROL]
(DVD only)
Enter a 4-digit password using the number
buttons, then press
.
The display for confirming the password
appears.
Playback of some DVD VIDEOs can be limited
according to a predetermined level such as the
age of the users. The [PARENTAL CONTROL]
function allows you to set a playback limitation
level.
x When you have already registered a
password
The display for entering the password
appears.
1
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears.
PARENTAL CONTROL
Enter password, then press ENTER
.
GB
64
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
Enter or re-enter your 4-digit password
using the number buttons, then press
.
8
Press X/x to select the level you want,
then press
.
Parental Control setting is complete.
The display for setting the playback
limitation level appears.
PARENTAL CONTROL
LEVEL:
4: PG13
USA
STANDARD:
PARENTAL CONTROL
LEVEL:
OFF
USA
STANDARD:
The lower the value, the stricter the
limitation.
To turn off the Parental Control
function
Press X/x to select [STANDARD], then
press
.
The selection items for [STANDARD] are
displayed.
Set [LEVEL] to [OFF] in Step 8.
To play a disc for which Parental
Control is set
PARENTAL CONTROL
1 Insert the disc and press H.
The display for entering your password
appears.
LEVEL:
OFF
USA
USA
STANDARD:
OTHERS
2 Enter your 4-digit password using the
number buttons, then press
.
The system starts playback.
6
7
Press X/x to select a geographic area
as the playback limitation level, then
Tip
• If you forget your password, remove the disc and
repeat steps 1 to 3 of “Preventing playback of specific
you are asked to enter your password, enter “199703”
press
.
The area is selected.
When you select [OTHERS t], select and
enter a standard code in the table of
(page 91) using the number buttons.
using the number buttons, then press
. The display
will ask you to enter a new 4-digit password. After
you enter a new 4-digit password, replace the disc in
the unit and press H. When the display for entering
your password appears, enter your new password.
Press X/x to select [LEVEL], then press
.
Note
The selection items for [LEVEL] are
displayed.
• When you play discs which do not have the Parental
Control function, playback cannot be limited on this
system.
• Depending on the disc, you may be asked to change
the parental control level while playing the disc. In
this case, enter your password, then change the level.
If the Resume Play mode is canceled, the level returns
to the previous level.
PARENTAL CONTROL
LEVEL:
OFF
OFF
STANDARD:
8:
7: NC17
6:
5:
R
continued
GB
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the password
Getting Optimal Surround
Sound for a Room
1
Press
in stop mode.
DISPLAY while the system is
The Control Menu display appears.
(SPEAKER FORMATION)
2
Press X/x to select
[PARENTAL CONTROL], then press
Depending on the shape of the room, there will
be some speakers you cannot install. For the
better surround sound, it is recommended that
first you decide the position of the speakers.
.
The options for [PARENTAL CONTROL]
appear.
1
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
3
Press X/x to select [PASSWORD t],
then press
.
The display for entering the password
appears.
2
Press
DISPLAY when the system is
in stop mode.
4
5
6
Enter your 4-digit password using the
The Control Menu display appears.
number buttons, then press
Enter a new 4-digit password using the
number buttons, then press
.
3
4
Press X/x to select
FORMATION], then press
[SPEAKER
.
.
To confirm your password, re-enter it
using the number buttons, then press
.
(
(
)
)
1
3
T
4 4
2 8
DVD VIDEO
0 : 0 3 : 0 4
SPEAKER FORMATION
SPEAKER FORMATION
AUTO CALIBRATION
If you make a mistake entering
your password
Press C before you press
correct number.
and input the
Press X/x to select [SPEAKER
FORMATION], then press
.
The options for [SPEAKER
FORMATION] appear.
SPEAKER FORMATION
STANDARD
GB
66
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press C/c to select a setting.
• [ALL FRONT]: when installing all the
speakers in front of the listening position.
• [STANDARD]: when installing all the
speakers normally.
• [ALL FRONT - NO CENTER]: when
installing the front and surround speakers
in front of the listening position.
Note
• When the wireless kit WAHT-SD1 (supplied
with DAV-HDX267W only) is installed,
[STANDARD (WIRELESS)] appears instead.
For details, see the operating instructions of the
WAHT-SD1.
• [NO CENTER]: when installing the front
and surround speakers.
• [SECOND ROOM]: when installing the
front speakers in one room and surround
speakers in another.
• [NO SURROUND]: when installing the
center and front speakers.
Note
• Speaker sound in the other room is the same as
that of the front and surround speakers.
• [FRONT ONLY]: when installing the
front speakers.
continued
GB
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
• When the wireless kit WAHT-SD1 (supplied
with DAV-HDX267W only) is installed,
[STANDARD (WIRED)] appears. For details,
see the operating instructions of the WAHT-
SD1.
Calibrating the
Appropriate Settings
Automatically
(AUTO CALIBRATION)
D. C. A. C. (Digital Cinema Auto Calibration)
can set the appropriate surround sound
automatically.
Note
• Loud test sound is output when [AUTO
CALIBRATION] starts. You cannot turn the volume
down. Give consideration to children and neighbor.
1
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
6
7
Press
.
The setting is made.
Press X/x to select [YES] or [NO], then
press
2
Press
DISPLAY when the system is
.
in stop mode.
• [YES]: continue with [AUTO
CALIBRATION], see Step 4 of
The Control Menu display appears.
3
4
Press X/x to select
[SPEAKER
FORMATION], then press
.
• [NO]: exit [SPEAKER FORMATION].
(
(
)
)
1
3
T
4 4
2 8
DVD VIDEO
SPEAKER FORMATION
0 : 0 3 : 0 4
SPEAKER FORMATION
SPEAKER FORMATION
AUTO CALIBRATION
Continue with AUTO CALIBRATION?
YES
NO
Press X/x to select [AUTO
CALIBRATION], then press
.
Note
• In order to enjoy the surround sound after you change
the position of the speakers, it is recommended you
set [SPEAKER FORMATION], and then set [AUTO
CALIBRATION].
The options for [AUTO CALIBRATION]
appear.
AUTO CALIBRATION
• To set [AUTO CALIBRATION], you need to
connect the supplied calibration mic.
Connect calibration mic. Start
measurement?
• The front panel display indicates the selected
[SPEAKER FORMATION]. It does not indicate the
speakers which output sound.
YES
NO
• When you change the [CONNECTION] setting in
[SPEAKER SETUP], the [SPEAKER
FORMATION] setting returns to [STANDARD].
GB
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the calibration mic to the A.CAL
MIC jack on the front panel, and set it up at
the ear level using a tripod, etc. (not
supplied). The front of each speaker should
face the calibration mic, and there should be
no obstruction between the speakers and the
calibration mic. Be quiet during the
measurement.
Note
• Avoid being in the measurement area and
making noise during the measurement (about
three minutes), to avoid measurement failure.
During the measurement, test signals are output
from the speakers.
• The environment of the room in which the
system is installed may affect measurements.
• If an error message appears, follow the message,
then select [YES].
An error message appears when:
– the headphones are connected.
– the calibration mic is not connected.
– front speakers are not correctly connected.
– surround speakers are not correctly
connected.
AUDIO IN / A.CAL MIC
Calibration mic
– front and surround speakers are not correctly
connected.
– there is excessive noise around the
calibration mic.
– the calibration mic is overloaded.
6
Press C/X/x/c to select [YES] or [NO],
then press
.
x The measurement is OK.
Disconnect the calibration mic, then select
[YES]. The result is implemented.
Measurement complete.
FRONT L :
FRONT R :
YES
YES
CENTER
:
NONE
SUBWOOFER : YES
SURROUND L : NONE
SURROUND R : NONE
If OK, unplug calibration mic and select
“YES”.
YES
NO
x The measurement is not OK.
Follow the message, then select [YES] to
retry.
5
Press X/x to select [YES], then press
.
Calibration starts.
Measurement failure.
Measuring. Please wait a moment.
Check speaker connection.
Retry?
YES
NO
Tip
• You can check the distance between the listening
continued
GB
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• While the Auto Calibration function works:
– do not turn off the power.
Using the Setup Display
– do not press any button.
By using the Setup Display, you can make
– do not change the volume.
– do not change the function.
– do not change the disc.
various adjustments to items such as picture and
sound.
For an overall list of Setup Display items, see
– do not insert or eject a disc.
– do not connect the headphones.
– do not disconnect the calibration mic.
• The measurement for [SUBWOOFER] is always
[YES] since the system does not perform subwoofer
calibration.
Displayed items vary depending on the country
model.
Note
• Playback settings stored in the disc take priority over
the Setup Display settings and not all the functions
described may work.
1
Press FUNCTION repeatedly until
“DVD” appears in the front panel
display.
2
Press
in stop mode.
DISPLAY when the system is
The Control Menu display appears.
3
4
Press X/x to select
then press
The options for [SETUP] appear.
[SETUP],
.
(
)
)
1 2 2 7
(
1 8 3 4
DVD VIDEO
T
0 : 0 0 : 0 2
QUICK
QUICK
CUSTOM
RESET
Press X/x to select [CUSTOM], then
press
.
The Setup Display appears.
LANGUAGE SETUP
OSD:
ENGLISH
ENGLISH
ORIGINAL
MENU:
AUDIO:
SUBTITLE:
AUDIO FOLLOW
GB
70
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press X/x to select the setup item from
the displayed list: [LANGUAGE
SETUP], [SCREEN SETUP], [CUSTOM
SETUP], or [SPEAKER SETUP]. Then
To reset all of the [SETUP]
settings
1 Select [RESET] in Step 4 and press
.
press
.
2 Select [YES] using X/x.
You can also quit the process and return to the
The Setup item is selected.
Example: [SCREEN SETUP]
Control Menu display by selecting [NO] here.
3 Press
.
Selected item
return to the default settings. Do not press [/
1 while resetting the system as it takes a few
seconds to complete.
SCREEN SETUP
TV TYPE:
16:9
ON
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
JACKET PICTURE
FULL
Note
• When you turn the system on after resetting and no
disc is in the unit, the guide message appears on the
Setup items
press
, to return to normal screen, press CLEAR.
6
7
Select an item using X/x, then press
.
The options for the selected item appear.
Example: [TV TYPE]
SCREEN SETUP
16:9
16:9
4:3 LETTER BOX
4:3 PAN SCAN
TV TYPE:
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
Options
Select a setting using X/x, then press
.
The setting is selected and setup is
complete.
SCREEN SETUP
TV TYPE:
4:3 LETTER BOX
ON
JACKET PICTURE
FULL
SCREEN SAVER:
BACKGROUND:
4:3 OUTPUT:
Selected setting
GB
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Display or
Sound Track Language
[LANGUAGE SETUP]
Settings for the Display
[SCREEN SETUP]
Choose settings according to the TV to be
connected.
[LANGUAGE SETUP] allows you to set
various languages for the on-screen display or
sound track.
Select [SCREEN SETUP] in the Setup Display.
For details, see “Using the Setup Display”
Select [LANGUAGE SETUP] in the Setup
Display. For details, see “Using the Setup
The default settings are underlined.
SCREEN SETUP
TV TYPE:
YCB
16:9
YCB
CR/RGB (HDMI):
CR
LANGUAGE SETUP
SCREEN SAVER:
BACKGROUND:
BLACK LEVEL:
ON
JACKET PICTURE
ON
OSD:
ENGLISH
ENGLISH
MENU:
AUDIO:
SUBTITLE:
ORIGINAL
OFF
BLACK LEVEL (COMPONENT OUT):
4:3 OUTPUT:
AUDIO FOLLOW
FULL
x [TV TYPE]
Selects the aspect ratio of the connected TV (4:3
standard or wide).
x [OSD] (On-Screen Display)
Switches the display language on the TV screen.
[16:9]
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
x [MENU] (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
[4:3 LETTER
BOX]
Select this when you connect a 4:3
screen TV. Displays a wide picture
with bands on the upper and lower
portions of the TV screen.
x [AUDIO] (DVD VIDEO only)
Switches the language of the sound track.
When you select [ORIGINAL], the language
given priority in the disc is selected.
[4:3 PAN SCAN]
Select this when you connect a 4:3
screen TV. Automatically displays
the wide picture on the entire
screen and cuts off the portions
that do not fit.
x [SUBTITLE] (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select [AUDIO FOLLOW], the
language for the subtitles changes according to
the language you selected for the sound track.
Tip
• If you select [OTHERS t] in [MENU], [AUDIO],
and [SUBTITLE], select and enter a language code
number buttons.
Note
• When you select a language in [MENU], [AUDIO],
or [SUBTITLE] that is not recorded on the DVD
VIDEO, one of the recorded languages will be
automatically selected (depending on the disc, the
language may not be selected automatically).
GB
72
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
[16:9]
• You cannot change the color system of the disc itself.
• You can change the color system of this system
x [SCREEN SAVER]
[4:3 LETTER BOX]
[4:3 PAN SCAN]
The screen saver image appears when you leave
the system in pause or stop mode for 15 minutes,
or when you play back a CD, DATA CD (MP3
audio), or DATA DVD (MP3 audio) for more
than 15 minutes. The screen saver will help
prevent your display device from becoming
damaged (ghosting). Press any button (e.g.,
button) to cancel the screen saver.
H
Note
[ON]
Turns on the screen saver.
Turns off the screen saver.
• Depending on the DVD, [4:3 LETTER BOX] may be
selected automatically instead of [4:3 PAN SCAN] or
vice versa.
[OFF]
x [BACKGROUND]
x [YCBCR/RGB (HDMI)]
Selects the type of HDMI signal output from
HDMI OUT jack.
Selects the background color or picture on the
TV screen in stop mode or while playing a CD,
DATA CD (MP3 audio), or DATA DVD (MP3
audio).
[YCBCR]
[RGB]
Outputs YCBCR signals.
Outputs RGB signals.
[JACKET
PICTURE]
The jacket picture (still picture)
appears, but only when the jacket
picture is already recorded on the
disc (CD-EXTRA, etc.). If the
disc does not contain a jacket
picture, the [GRAPHICS] picture
appears.
Note
• If the playback picture becomes distorted, set
[YCBCR] to [RGB].
• If the HDMI OUT jack is connected to equipment
with a DVI jack, [RGB] signals will be automatically
output even when you select [YCBCR].
[GRAPHICS]
A preset picture stored in the
system appears.
x [COLOR SYSTEM (VIDEO CD)]
[BLUE]
The background color is blue.
The background color is black.
(Asian, Australian, and Middle Eastern
models only)
[BLACK]
Select the color system when you play a VIDEO
CD.
x [BLACK LEVEL]
(North American, Mexican, and Latin
American models only)
[AUTO]
Outputs the video signal in the
system of the disc, either PAL or
NTSC. If your TV uses a DUAL
system, select [AUTO].
Selects the black level (setup level) for the video
signals output from the jacks other than
COMPONENT VIDEO OUT/HDMI OUT.
[PAL]
Changes the video signal of an
NTSC disc and outputs it in the
PAL system.
[ON]
Sets the black level of the output
signal to the standard level.
[NTSC]
Changes the video signal of a PAL
disc and outputs it in the NTSC
system.
[OFF]
Lowers the standard black level.
Use this when the picture becomes
too white.
continued
GB
73
Download from Www.Somanuals.com. All Manuals Search And Download.
x [BLACK LEVEL (COMPONENT OUT)]
Custom Settings
[CUSTOM SETUP]
(North American, Mexican, and Latin
American models only)
Selects the black level (setup level) for the video
signals output from the COMPONENT VIDEO
OUT jacks.
You cannot select this and the setting is not
effective when the system outputs progressive
signal.
Use this to set up playback related and other
settings.
Select [CUSTOM SETUP] in the Setup Display.
For details, see “Using the Setup Display”
[OFF]
[ON]
Sets the black level of the output
signal to the standard level.
The default settings are underlined.
CUSTOM SETUP
HDMI CONTROL:
PAUSE MODE:
TRACK SELECTION:
MULTI-DISC RESUME:
AUDIO DRC:
AUDIO (HDMI):
DivX:
Raise the standard black level.
Use this when the picture becomes
too black.
OFF
AUTO
OFF
ON
OFF
OFF
x [4:3 OUTPUT]
Registration Code
This setting is effective only when you set [TV
TYPE] in [SCREEN SETUP] to [16:9]
(page 72). Adjust to watch 4:3 aspect ratio
progressive signals. If you can change the aspect
ratio on your progressive format (525p/625p)
compatible TV, change the setting on your TV,
not the system. Note that this setting is effective
only for HDMI connection or progressive
signals output from the COMPONENT VIDEO
OUT jacks.
x [HDMI CONTROL]
Switches the HDMI CONTROL function on or
off. This function is available when you connect
the system and TV with the HDMI cord. For
details on this function, see the HDMI
CONTROL Guide (supplied separately).
[OFF]
[ON]
Sets the HDMI CONTROL
function to off.
Note
• This setting is effective only when
“PROGRESSIVE” is selected by using VIDEO
Sets the HDMI CONTROL
function to on.
You can operate mutually
between components that are
connected with the HDMI cord.
[FULL]
Select this when you can change
the aspect ratio on your TV.
[NORMAL]
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left and
right sides of the image.
Note
• When you set to [ON] without the HDMI connection
of the TV, [Please verify the HDMI connection]
appears and you can not set to [ON].
x [PAUSE MODE] (DVD VIDEO/DVD-R/
DVD-RW only)
Selects the picture in pause mode.
[AUTO]
The picture, including subjects
that move dynamically, is output
with no jitter. Normally select this
position.
16:9 aspect ratio TV
[FRAME]
The picture, including subjects
that do not move dynamically, is
output in high resolution.
GB
74
Download from Www.Somanuals.com. All Manuals Search And Download.
x [TRACK SELECTION] (DVD VIDEO only)
Gives the sound track which contains the highest
number of channels priority when you play a
DVD VIDEO on which multiple audio formats
(PCM, DTS, MPEG audio, or Dolby Digital
format) are recorded.
x [AUDIO (HDMI)]
Selects the audio output status from the HDMI
OUT jack.
[OFF]
[ON]
The sound is not output from the
HDMI OUT jack.
Outputs audio signals by
[OFF]
No priority given.
Priority given.
converting Dolby Digital, DTS, or
96 kHz/24 bit PCM signals to 48
kHz/ 16 bit PCM.
[AUTO]
Note
• When you set the item to [AUTO], the language may
change. The [TRACK SELECTION] setting has
higher priority than the [AUDIO] settings in
the disc, this function may not work.)
Note
• When you connect the unit and TV with the HDMI
cord and [ON] is selected, DYNAMIC BASS,
MOVIE/MUSIC, and sound field are not applied to
the sound that is output from the TV.
• If PCM, DTS, Dolby Digital sound, and MPEG audio
tracks have the same number of channels, the system
selects PCM, DTS, Dolby Digital sound, and MPEG
audio tracks in this order.
x [DivX]
(Except for United Kingdom and North
American models)
Displays the registration code for this system.
For more information, go to
http://www.divx.com on the Internet.
x [MULTI-DISC RESUME] (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off.
[ON]
Stores the resume settings in
memory for up to 40 discs.
[OFF]
Does not store the resume settings
in memory. Playback restarts at
the resume point only for the
current disc in the unit.
x [AUDIO DRC] (DVD VIDEO only)
Narrows the dynamic range of the sound track.
Useful for watching movies at low volume late
at night.
[OFF]
No compression of dynamic
range.
[STANDARD]
Reproduces the sound track with
the kind of dynamic range that the
recording engineer intended.
[MAX]
Compresses dynamic range fully.
GB
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• When you change the [CONNECTION] setting, the
[SPEAKER FORMATION] setting returns to
[STANDARD].
Settings for the Speakers
[SPEAKER SETUP]
x [DISTANCE (FRONT)]
To obtain the best possible surround sound, set
connection of the speakers and their distance
from your listening position. Then use the test
tone to adjust the level and the balance of the
speakers to the same level.
The default distance setting for the speakers in
relation to the listening position is shown below.
When you set the distance using the Quick Setup
(page 15), the settings is automatically
displayed.
Select [SPEAKER SETUP] in the Setup
Display. For details, see “Using the Setup
The default settings are underlined.
Note
• You cannot operate these setup items when you
connect headphones to the unit.
1.0 - 7.0 m3)
3 - 23 ft
/
0.0 - 7.0 m2)
0 - 23 ft
/
SPEAKER SETUP
CONNECTION:
DISTANCE(FRONT):
DISTANCE(SURROUND):
LEVEL(FRONT):
LEVEL(SURROUND):
TEST TONE:
FRONT:
OFF
YES
YES
YES
YES
CENTER:
SURROUND:
SUBWOOFER:
Be sure to change the value in the Setup Display
when you move the speakers.
To return to the default setting
when changing a setting
[L/R]
Front speaker distance from the
listening position can be set from
1.0 to 7.0 meters3) (3 to 23 ft).
Select the item, then press CLEAR. Note that
only the [CONNECTION] setting does not
return to the default setting.
3.0 m/10 ft1)
[CENTER]
Center speaker distance can be
moved up to 1.6 meters (5 ft)
closer to the listening position
from the front speaker distance.
3.0 m/10 ft1)
(appears when you
x [CONNECTION]
If you do not connect center or surround
speakers, set the parameters for [CENTER] and
[SURROUND]. Since the front speaker and
subwoofer setting is fixed, you cannot change
them.
set [CENTER] to
[YES] in the
[CONNECTION]
setting.)
default settings are changed.
2)0.0 to 6.9 meters for North American models.
3)0.9 to 6.9 meters for North American models.
[FRONT]
[YES]
[CENTER]
[YES]: Normally select this.
[NONE]: Select this if no center
speaker is used.
[SURROUND]
[YES]: Normally select this.
[NONE]: Select this if no
surround speaker is used.
x [DISTANCE (SURROUND)]
The default distance setting for the speakers in
relation to the listening position is shown below.
When you set the distance using the Quick Setup
(page 15), the settings is automatically
displayed.
[SUBWOOFER]
[YES]
GB
76
Download from Www.Somanuals.com. All Manuals Search And Download.
[SUBWOOFER]
+2.0 dB
Set this between –6.0 dB and
+6.0 dB.
x [LEVEL (SURROUND)]
You can vary the level of surround speakers as
follows. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
0.0 - 7.0 m2)
0 - 23 ft
/
[L/R]
0.0 dB
(appears when you
Set this between –6.0 dB and
+6.0 dB.
set [SURROUND]
to [YES] in the
[CONNECTION]
setting.)
Be sure to change the value in the Setup Display
when you move the speakers.
To adjust the volume of all the
speakers at one time
Turn the VOLUME control on the unit, or press
VOLUME +/– on the remote.
[L/R]
Surround speakers distance
can be moved up to 5.0 meters
(16 ft) closer to the listening
position from the front speaker
distance.
3.0 m/10 ft1)
(appears when you
x [TEST TONE]
set[SURROUND]to
[YES] in the
[CONNECTION]
setting.)
The speakers will emit a test tone to adjust
[LEVEL (FRONT)] and [LEVEL
(SURROUND)].
[OFF]
[ON]
The test tone is not emitted from the
speakers.
default settings are changed.
2)0.0 to 6.9 meters for North American models.
The test tone is emitted from each speaker
in sequence while adjusting level. When
you select one of the [SPEAKER SETUP]
items, the test tone is emitted from each
speaker in sequence.
Note
• If all front and surround speakers are not placed at an
equal distance from your listening position, set the
distance according to the closest speaker.
• Do not place the surround speakers farther away from
your listening position than the front speakers.
• Depending on the input stream, the [DISTANCE]
setting may not be effective.
Adjusting the speaker level by
using the test tone
1
2
3
4
Press
in stop mode.
DISPLAY when the system is
x [LEVEL (FRONT)]
You can vary the level of front speakers as
follows. Be sure to set [TEST TONE] to [ON]
for easy adjustment.
The Control Menu display appears.
Press X/x to select
then press
[SETUP],
.
[L/R]
0.0 dB
Set this between –6.0 dB and
0.0 dB.
The options for [SETUP] appear.
Press X/x to select [CUSTOM], then
press
[CENTER]
0.0 dB
(appears when you
Set this between –6.0 dB and
+6.0 dB.
.
The Setup Display appears.
set [CENTER] to
[YES] in the
[CONNECTION]
setting.)
Press X/x repeatedly to select
[SPEAKER SETUP], then press
c.
or
continued
GB
77
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Press X/x repeatedly to select [TEST
TONE], then press or c.
Returning to the Default
Settings
Press X/x repeatedly to select [ON],
then press
.
You will hear the test tone from each
speaker in sequence.
You can return the system parameters, such as
preset stations, to the default settings.
7
From your listening position, adjust the
value of [LEVEL (FRONT)] or [LEVEL
(SURROUND)] using C/X/x/c.
x
"/1
A
The test tone is emitted from only the
speaker which you are adjusting.
8
Press
making adjustments.
when you have finished
1
2
Press "/1 to turn on the system.
9
Press X/x repeatedly to select [TEST
TONE], then press
Press X/x repeatedly to select [OFF],
then press
.
Press x, A, and "/1 on the unit at the
same time.
10
“COLD RESET” appears in the front panel
display and the default settings are returned.
.
Note
• The test tone signals are not output from the HDMI
OUT jack.
GB
78
Download from Www.Somanuals.com. All Manuals Search And Download.
On adjusting volume
• Do not turn up the volume while listening to a section
with very low level inputs or no audio signals. If you
do, the speakers may be damaged when a peak level
section is suddenly played.
Additional Information
Precautions
On cleaning
On power sources
• Clean the cabinet, panel, and controls with a soft cloth
slightly moistened with a mild detergent solution. Do
not use any type of abrasive pad, scouring powder or
solvent such as alcohol or benzine.
If you have any questions or problems concerning
your system, please consult your nearest Sony dealer.
• Unplug the unit from the wall outlet if you do not
intend to use it for an extended period of time. To
disconnect the cord, pull it out by the plug, never by
the cord.
On placement
• Place the system in a location with adequate
ventilation to prevent heat build-up in the system.
• At high volume, over long periods of time, the cabinet
becomes hot to the touch. This is not a malfunction.
However, touching the cabinet should be avoided. Do
not place the unit in a confined space where
ventilation is poor as this may cause overheating.
• Do not block the ventilation slots by putting anything
on the system. The system is equipped with a high
power amplifier. If the ventilation slots are blocked,
the unit can overheat and malfunction.
On cleaning discs, disc/lens
cleaners
• Do not use cleaning discs or disc/lens cleaners
(including wet or spray types). These may cause
the apparatus to malfunction.
On your TV’s color
• If the speakers should cause the TV screen to have
color irregularity, turn off the TV then turn it on after
15 to 30 minutes. If color irregularity should persist,
place the speakers further away from the TV set.
• Do not place the unit on surfaces (rugs, blankets, etc.)
or near materials (curtains, draperies) that may block
the ventilation slots.
IMPORTANT NOTICE
Caution: This system is capable of holding a still
• Do not install the unit near heat sources such as
radiators, or air ducts, or in a place subject to direct
sunlight, excessive dust, mechanical vibration, or
shock.
video image or on-screen display image on your
television screen indefinitely. If you leave the still
video image or on-screen display image displayed
on your TV for an extended period of time you risk
permanent damage to your television screen.
Projection televisions are especially susceptible to
this.
• Do not install the unit in an inclined position. It is
designed to be operated in a horizontal position only.
• Keep the unit and discs away from equipment with
strong magnets, such as microwave ovens, or large
loudspeakers.
On moving the system
• Do not place heavy objects on the unit.
1 Press FUNCTION repeatedly to select
On operation
“DVD.”
• If the system is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lenses inside the control unit.
Should this occur, the system may not operate
properly. In this case, remove the disc and leave the
system turned on for about half an hour until the
moisture evaporates.
2 Make sure that all discs are removed from
the unit.
3 Press H and "/1 simultaneously.
“MECHA LOCK” appears in the front panel
display after “STANDBY.”
4 Remove the AC power cord (mains lead)
• When you move the system, take out any disc. If you
don’t, the disc may be damaged.
from the wall outlet (mains).
• If anything falls into the cabinet, unplug the unit and
have it checked by qualified personnel before
operating it any further.
GB
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes about the Discs
Troubleshooting
If you experience any of the following
difficulties while using the system, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should any
problem persist, consult your nearest Sony
dealer.
On handling discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not stick paper or tape on the disc.
Note that if service personnel changes some
parts during repair, these parts may be retained.
Power
The power is not turned on.
• Check that the AC power cord (mains lead) is
connected securely.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• Press "/1 after “STANDBY” disappears from the
front panel display.
If “PROTECTOR” and “PUSH POWER” appear
alternately in the front panel display.
Press "/1 to turn off the system, and check the
following items after “STANDBY” disappears.
• Are the + and – speaker cords short-circuited?
• Are you using only the specified speakers?
• Is anything blocking the ventilation holes of the
system?
• After playing, store the disc in its case.
On cleaning
• Before playing, clean the disc with a cleaning
cloth.
Wipe the disc from the center out.
After checking the above items and fixing any
problems, turn on the system. If the cause of the
problem cannot be found even after checking all the
above items, consult your nearest Sony dealer.
Picture
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
There is no picture.
• The video connecting cords are not connected
securely.
This system can only play back a standard
circular disc. Using neither standard nor circular
discs (e.g., card, heart, or star shape) may cause
a malfunction.
• The video connecting cords are damaged.
• The unit is not connected to the correct TV input
• The video input on the TV is not set so that you
can view pictures from the system.
Do not use a disc that has a commercially
available accessory attached, such as a label or
ring.
• You have set progressive format but your TV
cannot accept the signal in progressive format. In
this case, return the setting to interlace format (the
• Even if your TV is compatible with progressive
format (525p/625p) signals, the image may be
affected when you set progressive format. In this
case, return the setting to interlace format (the
• Re-connect the connecting cord securely.
• The unit is connected to an input device that is not
HDCP (high-bandwidth digital content
GB
80
Download from Www.Somanuals.com. All Manuals Search And Download.
protection) compliant (“HDMI” on the front panel
does not light up). See page 94.
• Make sure that no magnetic object (magnetic latch
on a TV stand, health care device, toy, etc.) is
placed near the speakers.
• If the HDMI OUT jack is used for video output,
changing the type of video signal output from the
HDMI OUT jack by pressing VIDEO FORMAT
Sound
There is no sound.
Connect the TV and the unit using a video jack
other than the HDMI OUT, and switch the TV’s
input to the connected video input so that you can
see the on-screen displays. Change the type of
video signal output from the HDMI OUT jack,
and switch the TV’s input back to HDMI. If the
picture still does not appear, repeat the steps and
try other options.
• The speaker cord is not connected securely.
• Press MUTING on the remote if “MUTING ON”
is displayed in the front panel display.
• The system is in pause mode or in Slow-motion
Play mode. Press H to return to normal play
mode.
• Fast forward or fast reverse is performed. Press
H to return to normal play mode.
• You have selected “PROGRESSIVE” using the
VIDEO FORMAT button on the remote
(“PROGRE” lights up in the front panel display)
even though your TV cannot accept the
progressive signal. In this case, disconnect the
HDMI cord from the unit and then select
“INTERLACE” so that “PROGRE” turns off.
• If the signal from the S VIDEO OUT jack is
distorted, change the type of video signal output
from the HDMI OUT jack by pressing VIDEO
• The equipment connected to the HDMI OUT jack
does not conform to the audio signal format, in
this case set [AUDIO (HDMI)] in [CUSTOM
SETUP] to [ON] (page 75).
No sound is output from the HDMI OUT jack.
• Set [AUDIO (HDMI)] in [CUSTOM SETUP] to
• The HDMI OUT jack is connected to a DVI
(digital visual interface) device (DVI (digital
visual interface) jacks do not accept audio
signals).
* Depending on the country, [720 × 576p] may
appear.
• Try the following: 1 Turn the system off and on
again. 2 Turn the connected equipment off and
on again. 3 Disconnect and then connect the
HDMI cord again.
Picture noise appears.
• The disc is dirty or flawed.
• If the picture output from your system goes
through your VCR to get to your TV, the copy-
protection signal applied to some DVD programs
could affect picture quality. If you still experience
problems even when you connect your unit
directly to your TV, try connecting your unit to
The left and right sounds are unbalanced or
reversed.
• Check that the speakers and components are
connected correctly and securely.
There is no sound from the subwoofer.
• Check the speaker connections and settings (page
Even though you set the aspect ratio in [TV
TYPE] of [SCREEN SETUP], the picture does
not fill the TV screen.
• The aspect ratio on the disc is fixed.
Severe hum or noise is heard.
• Check that the speakers and components are
connected securely.
Color irregularity occurs on the TV screen.
The subwoofer and the front speakers in this system
are magnetically shielded to prevent magnetic
leakage. However, some leakage may occur, as a
high-strength magnet is employed. If this happens,
check the following items:
• Check that the connecting cords are away from a
transformer or motor, and at least 3 meters (10 ft)
away from your TV set or a fluorescent light.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a
cloth slightly moistened with alcohol.
• Clean the disc.
• If the speakers are used with a CRT-based TV or
projector, install the speakers at least 0.3 meters
(1.0 ft) from the TV set.
• If the color irregularity persists, turn off the TV set
once, then turn it on after 15 to 30 minutes.
• If howling occurs, reposition the speakers farther
away from the TV set.
continued
GB
81
Download from Www.Somanuals.com. All Manuals Search And Download.
• Press DISPLAY so that the frequency appears in
the front panel display.
The sound loses stereo effect when you play a
VIDEO CD, a CD, or an MP3.
• Set [AUDIO] to [STEREO] by pressing AUDIO
The remote does not function.
• There are obstacles between the remote and the
unit.
• Make sure the unit is connected properly.
• The distance between the remote and the unit is
too far.
The surround effect is difficult to hear when
you are playing a Dolby Digital, DTS, or MPEG
audio sound track.
• Check the speaker connections and settings (page
• The remote is not pointed at the remote sensor on
the unit.
• The batteries in the remote are weak.
The disc does not play.
• Depending on the DVD, the output signal may not
be the entire 5.1 channel. It may be monaural or
stereo even if the sound track is recorded in Dolby
Digital or MPEG audio format.
• There is no disc inserted.
• The disc is upside down.
Insert the disc with the playback side facing down.
• The disc is skewed on the disc tray.
• The region code on the DVD does not match the
system.
The sound comes from the center speaker
only.
• Depending on the disc, the sound may come from
the center speaker only.
• Moisture has condensed inside the unit and may
cause damage to the lenses. Remove the disc and
leave the unit turned on for about half an hour.
No sound is heard from the center speaker.
• Check the speaker connections and settings (page
The MP3 audio track cannot be played.
• The DATA CD is not recorded in the MP3 format
that conforms to ISO 9660 Level 1/Level 2, or
Joliet.
• Depending on the source, the effect of the center
speaker may be less noticeable.
• The DATA DVD is not recorded in an MP3
format that conforms to UDF (Universal Disk
Format).
• A 2 channel source is being played.
No sound or only a very low-level sound is
heard from the surround speakers.
• Check the speaker connections and settings (page
• The MP3 audio track does not have the extension
“.MP3.”
• The data is not formatted in MP3 even though it
has the extension “.MP3.”
• Depending on the source, the effect of the
surround speakers may be less noticeable.
• A 2 channel source is being played.
• The data is not MPEG1 Audio Layer 3 data.
• The system cannot play audio tracks in MP3PRO
format.
There is no sound from the speakers that are
indicated in the front panel display.
• The [MODE (MP3, JPEG)] setting has been set to
• The front panel display indicates the selected
[SPEAKER FORMATION]. It does not indicate
• If you cannot change the [MODE (MP3, JPEG)]
setting, re-load the disc or turn the system off, then
on.
• The DATA CD/DATA DVD contains a DivX
video file (except for United Kingdom and North
American models).
Operation
Radio stations cannot be tuned in.
• Check that the antenna (aerial) is connected
securely. Adjust the antenna (aerial) or connect an
external antenna (aerial) if necessary.
The JPEG image file cannot be played.
• The DATA CD is not recorded in a JPEG format
that conforms to ISO 9660 Level 1/Level 2, or
Joliet.
• The signal strength of the stations is too weak
(when tuning in with automatic tuning). Use direct
tuning.
• The DATA DVD is not recorded in a JPEG format
that conforms to UDF (Universal Disk Format).
• It has an extension other than “.JPEG” or “.JPG.”
• It is larger than 3,072 (width) × 2,048 (height) in
normal mode, or more than 2,000,000 pixels in
• No stations have been preset or the preset stations
have been cleared (when tuning by scanning
GB
82
Download from Www.Somanuals.com. All Manuals Search And Download.
Progressive JPEG which is mainly used on the
Internet WEB site.
You cannot perform some functions such as
Stop, Search, Slow-motion Play, or Repeat
Play.
• Depending on the disc, you may not be able to
perform some of the operations above. See the
operating instructions that came with the disc.
• It does not fit the TV screen (those images are
reduced).
• The [MODE (MP3, JPEG)] setting has been set to
[AUDIO (MP3)] (page 50).
• If you cannot change the [MODE (MP3, JPEG)]
setting, re-load the disc or turn the system off, then
on.
Messages do not appear on the TV screen in
the language you want.
• In the Setup Display, select the desired language
for the on-screen display in [OSD] under
[LANGUAGE SETUP] (page 72).
• The DATA CD/DATA DVD contains a DivX
video file (except for United Kingdom and North
American models).
The language for the sound track cannot be
changed.
• Multilingual tracks are not recorded on the DVD
being played.
The MP3 audio tracks and JPEG image file
starts playing simultaneously.
• [AUTO] has been selected in [MODE (MP3,
• The DVD prohibits changing the language for the
sound track.
The DivX video file cannot be played (except
for United Kingdom and North American
models).
• The file is not created in DivX format.
• The file has an extension other than “.AVI” or
“.DIVX.”
The subtitle language cannot be changed.
• Multilingual subtitles are not recorded on the
DVD being played.
• The DVD prohibits changing the subtitles.
• The DATA CD/DATA DVD is not created in a
DivX format that conforms to ISO 9660 Level 1/
Level 2 or, Joliet/UDF.
The subtitle cannot be turned off.
• The DVD prohibits turning off subtitles.
The angles cannot be changed.
• Multi-angles are not recorded on the DVD being
• The DivX video file is larger than 720 (width) ×
576 (height).
The titles of album/track/file name are not
displayed correctly.
• The system can only display numbers and letters
of the alphabets. Other characters are displayed as
[*].
• The DVD prohibits changing the angles.
A disc cannot be ejected and “LOCKED”
appears in the front panel display.
• Contact your Sony dealer or local authorized Sony
service facility.
A disc does not start playing from the
beginning.
• Program Play, Shuffle Play, or Repeat Play has
been selected.
[Data error] appears on the TV screen when
playing a DATA CD or DATA DVD.
• The MP3 audio track/JPEG image file/DivX
video file* you want to play is broken.
• The data is not MPEG1 Audio Layer 3 data.
• The JPEG image file format does not conform to
DCF.
Press CLEAR to cancel these functions before
playing a disc.
• Resume Play has been selected.
During stop, press x on the unit or the remote and
• The JPEG image file has the extension “.JPG” or
“.JPEG,” but is not in JPEG format.
• The file you want to play has the extension “.AVI”
or “.DIVX” but is not in DivX format, or is in
DivX format but does not conform to a DivX
Certified profiles.*
• The title, DVD or PBC menu automatically
appears on the TV screen.
The system starts playing the disc
automatically.
• The DVD features an auto playback function.
* Except for United Kingdom and North American
models.
Playback stops automatically.
• Some discs may contain an auto pause signal.
While playing such a disc, the system stops
playback at the auto pause signal.
The system does not work normally.
• Disconnect the AC power cord (mains lead) from
the wall outlet (mains), then reconnect after
several minutes.
continued
GB
83
Download from Www.Somanuals.com. All Manuals Search And Download.
The unit does not work and “CHILD LOCK”
appears in the front panel display when you
press any button on the unit.
Self-diagnosis Function
(When letters/numbers appear in the
display)
The HDMI CONTROL function does not work.
• When “HDMI” does not light up in the front panel
• Set the [HDMI CONTROL] setting in [CUSTOM
When the self-diagnosis function is activated to
prevent the system from malfunctioning, a 5-
character service number (e.g., C 13 50) with a
combination of a letter and 4 digits appears on
the TV screen or front panel display. In this case,
check the following table.
• Make sure that the connected component is
compatible with the HDMI CONTROL function.
• Check that the AC power cord (mains lead) of the
connected component is connected securely.
• Check the connected component’s setting for the
HDMI CONTROL function. See the operating
instructions of the component.
C:13:50
• If you change the HDMI connection, connect and
disconnect the AC power cord (mains lead), or
have a power failure, set the [HDMI CONTROL]
setting in [CUSTOM SETUP] to [OFF], then set
the [HDMI CONTROL] setting in [CUSTOM
First 3
Cause and/or corrective action
characters of
the service
number
C 13
The disc is dirty.
• For details on the HDMI CONTROL function, see
the HDMI CONTROL Guide (supplied
separately).
,Clean the disc with a soft cloth
C 31
The disc is not inserted correctly.
,Restart the system, then re-insert
the disc correctly.
No sound is output from the system and TV
while using the System Audio Control
function.
E XX
To prevent a malfunction, the
system has performed the self-
diagnosis function.
• Set the [AUDIO (HDMI)] setting in [CUSTOM
(xx is a number)
• Make sure that the connected TV is compatible
with the System Audio Control function.
• For details on the System Audio Control function,
see the HDMI CONTROL Guide (supplied
separately).
,Contact your nearest Sony
dealer or local authorized Sony
service facility and give the 5-
character service number.
Example: E 61 10
When displaying the version
number on the TV screen
When you turn on the system, the version
number [VER.X.XX] (X is a number) may
appear on the TV screen. Although this is not a
malfunction and for Sony service use only,
normal system operation will not be possible.
Turn off the system, and then turn on the system
again to operate.
VER.X.XX
GB
84
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD system
Laser
Semiconductor laser
(DVD: λ = 650 nm)
(CD: λ = 790 nm)
Emission duration:
continuous
Specifications
AUDIO POWER SPECIFICATIONS
for the US model
POWER OUTPUT AND TOTAL HARMONIC
Signal format system
North American models: NTSC
Other models:
DISTORTION:
With 3 ohms loads, both
PAL/NTSC
channels driven, from 120
- 20,000 Hz; rated 84 watts
per channel minimum
RMS power, with no more
than 0.7 % total harmonic
distortion from 250 milli
watts to rated output.
Tuner section
System
PLL quartz-locked digital
synthesizer
FM tuner section
Tuning range
North American models: 87.5-108.0 MHz (100 kHz
step)
Amplifier section
DAV-HDX265/DAV-HDX267W
US models:
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:143watts
(per channel at 3 ohms, 1
kHz, 10 % THD)
Other models:
87.5-108.0 MHz (50 kHz
step)
FM wire antenna (aerial)
Antenna (aerial)
Antenna (aerial) terminals 75 ohms, unbalanced
Intermediate frequency
AM tuner section
Tuning range
North American, Mexican, and Latin American
models:
10.7 MHz
Subwoofer*: 285 watts (at
1.5 ohms, 80 Hz, 10 %
THD)
530 – 1,710 kHz (with the
interval set at 10 kHz)
531 – 1,710 kHz (with the
interval set at 9 kHz)
Other models:
Stereo mode (rated)
108 W + 108 W (at 3 ohms,
1 kHz, 1 % THD)
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:143watts
European, Russian, and Middle Eastern models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
Australian and New Zealand models:
531 – 1,710 kHz (with the
interval set at 9 kHz)
(per channel at 3 ohms, 1
kHz, 10 % THD)
Subwoofer*: 285 watts (at
1.5 ohms, 80 Hz, 10 %
THD)
530 – 1,710 kHz (with the
interval set at 10 kHz)
DAV-HDX266
Surround mode (reference) RMS output power
FL/FR/C/SL/SR*:142watts
Other models:
531 – 1,602 kHz (with the
interval set at 9 kHz)
530 – 1,610 kHz (with the
interval set at 10 kHz)
AM loop antenna (aerial)
450 kHz
(per channel at 3 ohms, 1
kHz, 10 % THD)
Subwoofer*: 140 watts (at
3 ohms, 80 Hz, 10 % THD)
Antenna (aerial)
Intermediate frequency
Video section
Outputs
*
Depending on the sound field settings and the source,
there may be no sound output.
VIDEO: 1 Vp-p 75 ohms
S VIDEO:
Inputs (Analog)
TV/VIDEO (AUDIO IN) Sensitivity: 450/250 mV
AUDIO IN
Outputs (Analog)
Phones
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.7 Vp-p
75 ohms
Sensitivity: 250/125 mV
Accepts low-and high-
impedance headphones.
HDMI OUT: Type A (19
pin)
continued
GB
85
Download from Www.Somanuals.com. All Manuals Search And Download.
Speakers
General
Power requirements
North American models: 120 V AC, 60 Hz
Other models:
Power consumption
Front (SS-TS72)
Speaker system
Bass reflex, magnetically
shielded
65 mm (2 /8 inches) dia,
220 - 240 V AC, 50/60 Hz
5
Speaker unit
DAV-HDX265/DAV-HDX267W:
cone type
3.0 ohms
On: 175 W
Rated impedance
Dimensions (approx.)
3
Standby: 0.3 W (at the
Power Saving mode)
On: 150 W
93 × 221 × 75 mm (3 /4 ×
3
8 /4 × 3 inches) (w/h/d)
DAV-HDX266:
Mass (approx.)
0.7 kg (1 lb 9 oz)
Standby: 0.3 W (at the
Power Saving mode)
Output voltage (DIGITAL MEDIA PORT)
DC 5 V
Output current (DIGITAL MEDIA PORT)
700 mA
Center (SS-CT71)
Speaker system
Bass reflex, magnetically
shielded
65 mm (2 /8 inches) dia,
5
Speaker unit
cone type
3.0 ohms
Rated impedance
Dimensions (approx.)
Dimensions (approx.)
3
261 × 91 × 80 mm (10 /8 ×
DAV-HDX265/DAV-HDX266:
5
1
3 /8 × 3 /4 inches) (w/h/d)
0.7 kg (1 lb 9 oz)
430 × 86 × 415 mm (17 ×
Mass (approx.)
1
3
3 /2 × 16 /8 inches) (w/h/d)
incl. projecting parts
Surround (SS-TS71)
Speaker system
Bass reflex, magnetically
shielded
65 mm (2 /8 inches) dia,
DAV-HDX267W:
Mass (approx.)
DAV-HDX265/DAV-HDX266:
5.2 kg (11 lb 8 oz)
DAV-HDX267W: 5.4 kg (11 lb 15 oz)
430 × 86 × 435 mm (17 ×
3 /2 × 17 /4 inches) (w/h/d)
incl. projecting parts
1
1
5
Speaker unit
cone type
3.0 ohms
Rated impedance
Dimensions (approx.)
3
93 × 162 × 75 mm (3 /4 ×
1
6 /2 × 3 inches) (w/h/d)
Mass (approx.)
0.6 kg (1 lb 6 oz)
Design and specifications are subject to change
without notice.
Subwoofer (DAV-HDX265/DAV-HDX267W)
(SS-WS74)
Unpacking
• Front speakers (2)
Speaker system
Speaker unit
Bass reflex
160 mm (6 /8 inches) dia,
cone type
3
• Center speaker (1)
• Surround speakers (2)
Rated impedance
Dimensions (approx.)
1.5 ohms
• Subwoofer (1)
3
220 × 394 × 350 mm (8 /4
• AM loop antenna (aerial) (1)
• FM wire antenna (aerial) (1)
• Speaker cords (6, red/white/green/gray/blue/purple)
• Video Cord (1)
5
7
× 15 /8 × 13 /8 inches)
(w/h/d)
Mass (approx.)
6.5 kg (14 lb 6 oz)
Subwoofer (DAV-HDX266)
(SS-WS72)
• Remote Commander (remote) (1)
• R6 (size AA) batteries (2)
• Calibration mic (1)
Speaker system
Speaker unit
Bass reflex
160 mm (6 /8 inches) dia,
3
• Foot pads (1 set)
cone type
3.0 ohms
• WAHT-SD1 (1) (DAV-HDX267W only)
• Operating Instructions
Rated impedance
Dimensions (approx.)
3
220 × 394 × 350 mm (8 /4
• HDMI CONTROL Guide
• Speaker and TV connections (card)
5
7
× 15 /8 × 13 /8 inches)
(w/h/d)
Mass (approx.)
6.5 kg (14 lb 6 oz)
GB
86
Download from Www.Somanuals.com. All Manuals Search And Download.
•Standby power consumption 0.3 W (or
less).
Glossary
•Halogenated flame retardants are not
used in the printed wiring boards.
•Over 85 % power efficiency of
amplifier block is achieved with the
full digital amplifier, S-master.
Album
Section of a music piece or an image on a data
CD containing MP3 audio tracks or JPEG files.
Chapter
Subdivision of a title on a DVD. A title is
composed of several chapters.
Digital Cinema Auto Calibration
Digital Cinema Auto Calibration was developed
by Sony to automatically measure and adjusts
the speaker settings to your listening
environment in a short period of time.
Digital Direct Twin Drive Subwoofer
(DAV-HDX265/DAV-HDX267W only)
Utilizing Sony's proprietary S-Master
technology, the Digital Direct Twin Drive
Subwoofer features two S-Master Digital
Amplifiers that provide dedicated power to a
strategically located subwoofer for astounding
sound performance. Easy to set up, Digital
Direct Twin Drive Subwoofer provides a stable
sound field over a much larger listening area
without having to adjust frequency levels.
®
DivX (except for United Kingdom
and North American models)
Digital video technology created by DivX, Inc.
Videos encoded with DivX technology are
among the highest quality with a relatively small
file size.
Dolby Digital
This movie theater sound format is more
advanced than Dolby Surround Pro Logic. In
this format, the surround speakers output stereo
sound with an expanded frequency range, and a
subwoofer channel for deep bass is
independently provided. This format is also
called “5.1” with the subwoofer channel
designed as the 0.1 channel (since it functions
only when a deep bass effect is needed). All six
channels in this format are recorded separately
for superior channel separation. Furthermore,
since all the signals are processed digitally, less
signal degradation occurs.
continued
GB
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Dolby Pro Logic II
DVD
Dolby Pro Logic II creates five full-bandwidth
output channels from 2 channel sources. This is
done using an advanced, high-purity matrix
surround decoder that extracts the spatial
properties of the original recording without
adding any new sounds or tonal colorations.
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same as
a CD.
The data capacity of a single-layer and single-
sided DVD, at 4.7 GB (Giga Byte), is 7 times
that of a CD. Furthermore, the data capacity of a
dual-layer and single-sided DVD is 8.5 GB, a
single-layer and double-sided DVD 9.4 GB, and
a dual-layer and double-sided DVD 17 GB.
The picture data uses the MPEG 2 format, one of
a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/40 of its original size. The DVD also
uses the variable rate coding technology that
processes allocated data according to the status
of the picture.
The audio data is recorded in Dolby Digital as
well as in PCM, allowing you to enjoy more
realistic audio presence.
Furthermore, various advanced functions such
as the multi-angle, multilingual, and Parental
Control functions are provided with the DVD.
x Movie mode
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby
Surround. The result is enhanced sound field
directionality that approaches the quality of
discrete 5.1-channel sound.
x Music mode
The Music mode is for use with any stereo music
recordings, and provides a wide and deep sound
space.
Dolby Surround Pro Logic
As one method of decoding Dolby Surround,
Dolby Surround Pro Logic produces four
channels from 2 channel sound. Compared with
the former Dolby Surround system, Dolby
Surround Pro Logic reproduces left-to-right
panning more naturally and localizes sounds
more precisely. To take full advantage of Dolby
Surround Pro Logic, you should have one pair of
surround speakers and a center speaker. The
surround speakers output monaural sound.
DVD+RW
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD VIDEO
format.
DVD-RW
DTS
A DVD-RW is a recordable and rewritable disc
that is the same size as a DVD VIDEO. The
DVD-RW has two different modes: VR mode
and Video mode. DVD-RWs created in Video
mode have the same format as a DVD VIDEO,
while discs created in VR (Video Recording)
mode allow the contents to be programmed or
edited.
Digital audio compression technology
developed by DTS, Inc. This technology
conforms to 5.1-channel surround. This format
comprises of stereo rear channel and there is
discrete subwoofer channel in this format. DTS
provides the same 5.1 discrete channels of high
quality digital audio. The good channel
separation is realized due to the all channel data
being recorded discretely and processed in
digitally.
File
A JPEG image or a DivX video* recorded on a
DATA CD/DATA DVD. (“File” is an exclusive
definition for this system.) A single file consists
of a single image or movie.
* Except for United Kingdom and North American
models.
GB
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Film based software, Video based
software
PCM (Pulse Code Modulation)
A method for converting analog audio to digital
audio. It is used for the Compact Disc (CD)
audio format.
DVDs can be classified as Film based or Video
based software. Film based DVDs contain the
same images (24 frames per second) that are
shown at movie theaters. Video based DVDs,
such as television dramas or sit-coms, displays
images at 30 frames (or 60 fields) per second.
Playback Control (PBC)
Signals encoded on VIDEO CDs (Version 2.0)
to control playback.
By using menu screens recorded on VIDEO
CDs with PBC functions, you can enjoy playing
simple interactive programs, programs with
search functions, and so on.
HDMI (high-definition multimedia
interface)
HDMI is an interface that supports both video
and audio on a single digital connection,
allowing you to enjoy high quality digital
picture and sound. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding technology
for digital video signals.
Progressive format
(sequential scanning)
In contrast to the Interlace format, the
progressive format can reproduce 50 - 60 frames
per second by reproducing all scanning lines
(525 lines for the NTSC system, 625 lines for the
PAL system). The overall picture quality
increases and still images, text and horizontal
lines appear sharper. This format is compatible
with the 525 or 625 progressive format.
Interlace format
(Interlaced scanning)
The Interlace format is the NTSC standard
method for displaying TV images at 30 frames
per second. Each frame is scanned twice -
alternately between the even numbered scanning
lines and then odd numbered scanning lines, at
60 times per second.
Region Code
This system is used to protect copyrights. A
region number is allocated on each DVD system
or DVD disc according to the sales region. Each
region code is shown on the system as well as on
the disc packaging. The system can play discs
that match its region code. The system can also
MPEG audio
A coding system to compress digital audio
signals. MPEG-1 is used for MP3 (MPEG-1
Audio Layer-3). MPEG-2 is used for one of the
audio format of DVD.
ALL
play discs with the “ ” mark. Even when the
region code is not shown on the DVD, the region
limit may still apply.
Multi-angle function
Scene
Various angles of a scene, or viewpoints of the
video camera are recorded on some DVDs.
On a VIDEO CD with PBC (playback control)
functions, the menu screens, moving pictures
and still pictures are divided into sections called
“scenes.”
Multilingual function
Several languages for the sound or subtitles in a
picture are recorded on some DVDs.
Title
The longest section of a picture or music feature
on a DVD, movie, etc., in video software, or the
entire album in audio software.
Parental Control
A function of the DVD to limit playback of the
disc by the age of the users according to the
limitation level in each country. The limitation
varies from disc to disc; when it is activated,
playback is completely prohibited, violent
scenes are skipped or replaced with other scenes
and so on.
Track
Section of a picture or a music piece on a
VIDEO CD, CD, or MP3. An album is
composed of several tracks (MP3 only).
continued
GB
89
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO CD
A compact disc that contains moving pictures.
The picture data uses the MPEG 1 format, one of
a worldwide standard of digital compression
technology. The picture data is compressed to
about 1/140 of its original size. Consequently, a
12 cm VIDEO CD can contain up to 74 minutes
of moving pictures.
VIDEO CDs also contain compact audio data.
Sounds outside the range of human hearing are
compressed while sounds we can hear are not
compressed. VIDEO CDs can hold six times the
audio information of conventional audio CDs.
There are two versions of VIDEO CDs.
• Version 1.1: You can play only moving
pictures and sounds.
• Version 2.0: You can play high-resolution still
pictures and enjoy PBC functions.
This system conforms to both versions.
GB
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code List
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027 Afar
1183 Irish
1347 Maori
1507 Samoan
1508 Shona
1509 Somali
1511 Albanian
1512 Serbian
1513 Siswati
1514 Sesotho
1515 Sundanese
1516 Swedish
1517 Swahili
1521 Tamil
1028 Abkhazian
1032 Afrikaans
1039 Amharic
1044 Arabic
1045 Assamese
1051 Aymara
1052 Azerbaijani
1053 Bashkir
1057 Byelorussian
1059 Bulgarian
1060 Bihari
1061 Bislama
1066 Bengali;
Bangla
1067 Tibetan
1070 Breton
1079 Catalan
1093 Corsican
1097 Czech
1103 Welsh
1105 Danish
1109 German
1130 Bhutani
1142 Greek
1144 English
1145 Esperanto
1149 Spanish
1150 Estonian
1151 Basque
1157 Persian
1165 Finnish
1166 Fiji
1186 Scots Gaelic
1194 Galician
1196 Guarani
1203 Gujarati
1209 Hausa
1349 Macedonian
1350 Malayalam
1352 Mongolian
1353 Moldavian
1356 Marathi
1357 Malay
1358 Maltese
1363 Burmese
1365 Nauru
1217 Hindi
1226 Croatian
1229 Hungarian
1233 Armenian
1235 Interlingua
1239 Interlingue
1245 Inupiak
1248 Indonesian
1253 Icelandic
1254 Italian
1257 Hebrew
1261 Japanese
1269 Yiddish
1283 Javanese
1287 Georgian
1297 Kazakh
1298 Greenlandic
1299 Cambodian
1300 Kannada
1301 Korean
1305 Kashmiri
1307 Kurdish
1311 Kirghiz
1369 Nepali
1376 Dutch
1525 Telugu
1527 Tajik
1528 Thai
1379 Norwegian
1393 Occitan
1403 (Afan)Oromo
1408 Oriya
1417 Punjabi
1428 Polish
1435 Pashto;
Pushto
1436 Portuguese
1463 Quechua
1481 Rhaeto-
Romance
1482 Kirundi
1483 Romanian
1489 Russian
1491 Kinyarwanda
1495 Sanskrit
1498 Sindhi
1501 Sangho
1502 Serbo-
Croatian
1529 Tigrinya
1531 Turkmen
1532 Tagalog
1534 Setswana
1535 Tonga
1538 Turkish
1539 Tsonga
1540 Tatar
1543 Twi
1557 Ukrainian
1564 Urdu
1572 Uzbek
1581 Vietnamese
1587 Volapük
1613 Wolof
1632 Xhosa
1665 Yoruba
1684 Chinese
1697 Zulu
1313 Latin
1326 Lingala
1327 Laothian
1332 Lithuanian
1334 Latvian;
Lettish
1171 Faroese
1174 French
1181 Frisian
1503 Singhalese
1505 Slovak
1506 Slovenian
1345 Malagasy
1703 Not specified
Parental Control Area Code List
Code Area
Code Area
Code Area
Code Area
2044 Argentina
2047 Australia
2046 Austria
2057 Belgium
2070 Brazil
2079 Canada
2090 Chile
2165 Finland
2174 France
2109 Germany
2248 India
2238 Indonesia
2254 Italy
2276 Japan
2304 Korea
2363 Malaysia
2362 Mexico
2149 Spain
2376 Netherlands
2390 New Zealand
2379 Norway
2499 Sweden
2086 Switzerland
2528 Thailand
2184 United
Kingdom
2427 Pakistan
2424 Philippines
2436 Portugal
2489 Russia
2092 China
2115 Denmark
2501 Singapore
GB
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear panel
Screws*
DIR-TC1
AM
Y
P
B/CB
PR/CR
R
AUDIO IN
L
S
VIDEO
(DVD ONLY)
FM
75
(DVD ONLY)
COAXIAL
ANTENNA
TV/VIDEO
FRONT
R
FRONT
L
SUR
R
SUR
L
COMPONENT VIDEO OUT
VIDEO
SPEAKER
MONITOR OUT
OUT
DMPORT
(DVD ONLY)
CENTER
WOOFER
SPEAKER
*
CAUTION
Please do not remove the screws before
installing the WAHT-SD1.
F MONITOR OUT (S VIDEO/VIDEO) jacks
G DMPORT (DIGITAL MEDIA PORT) jack
continued
GB
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Front panel display
About the indications in the front panel display
A Lights up when the HDMI OUT jack is
correctly connected to HDCP (high-
bandwidth digital content protection)
compliant device with HDMI or DVI
(digital visual interface) input. (20)
J Lights up when the child lock function
is set to on. (62)
K Lights up when the system outputs
progressive signals (DVD function
B Lights up when the time information of
a title or chapter appears in the front
panel display. (DVD only) (42)
L Indicates the selected [SPEAKER
FORMATION]. (66)
C Lights up when the color system is set
to NTSC. (Asian, Australian, and Middle
Eastern models only)
M Current surround format (Except for
JPEG)
N Lights up when the DYNAMIC BASS is
D Lights up when a station is received.
selected. (59)
O Displays system’s status such as
chapter, title, or track number, time
information, radio frequency, playing
status, sound field, etc.
E Stereo/Monaural effect (Radio only)
F Lights up when the sleep timer is set.
G Lights up when the movie or music
mode is selected. (29)
H Playing status (DVD function only)
GB
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the Control Menu Display
DISPLAY
Use the Control Menu display to select a function and to view related information. Press
repeatedly to turn on or change the Control Menu display as follows:
DISPLAY
, Control Menu display 1
m
Control Menu display 2 (appears for certain discs only)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For details
about each item, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
continued
GB
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Currently playing title number1)
Currently playing chapter number2)
Total number of titles1)
Playback status
(N Playback,
X Pause,
Total number of chapters2)
Control Menu items
x Stop, etc.)
(
)
)
1 2 2 7
Type of disc being
played3)
(
1 8 3 4
DVD VIDEO
T
1 : 3 2 : 5 5
Playing time4)
Current setting
Options
Selected item
OFF
OFF
DISC
TITLE
CHAPTER
Function name of
selected Control
Menu item
REPEAT
ENTER
DISPLAY
Quit:
Operation message
1) Displays the scene number for VIDEO CDs (PBC is on), track number for VIDEO CDs/CDs, album number for
DATA CDs/DATA DVDs. DivX video album number for DATA CDs/DATA DVDs (Except for United Kingdom
and North American models).
2) Displays the index number for VIDEO CDs, MP3 audio track number, or JPEG image file number for DATA CDs/
DATA DVDs. DivX video file number for DATA CDs/DATA DVDs (Except for United Kingdom and North
American models).
3) Displays Super VCD as “SVCD.” Displays “MP3” in the Control Menu display 1 or “JPEG” in the Control Menu
display 2 for DATA CDs/DATA DVDs.
4) Displays the date for JPEG files.
To turn off the display
Press
DISPLAY.
List of Control Menu items
Item
Item Name, Function, Relevant Disc Type
Selects the title, scene, or track to be played.
Selects the chapter or index to be played.
Selects the track to be played.
Selects the type of titles (DVD-RW/DVD-R) to be played, the [ORIGINAL] one, or an edited
[PLAY LIST].
GB
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/CD text or the MP3 track name.
Sets the speaker formation./Adjust the level of each speaker automatically.
Selects the track to play in the order you want.
[SHUFFLE] (page 37)
Plays the track in random order.
[REPEAT] (page 38)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/track/album
repeatedly.
[A/V SYNC] (page 45)
Adjusts the delay between the picture and sound.
*
*
Sets to prohibit playback on this system.
[SETUP] (page 70)
Use Quick Setup to choose the desired language of the on-screen display, the aspect ratio of
the TV, speaker formation, and choose yes or no to start the Auto Calibration.
[CUSTOM] Setup
In addition to the Quick Setup setting, you can adjust various other settings.
[RESET]
Returns the settings in [SETUP] to the default setting.
[ALBUM] (page 33)
Selects the album to be played.
[FILE] (page 33)
Selects the JPEG image file or DivX video file* to be played.
[DATE] (page 44)
Displays the date the picture was taken by a digital camera.
**
**
**
**
Specifies the duration for which the slides are displayed on the TV screen.
[EFFECT] (page 51)
Selects the effects to be used for changing slides during a slide show.
[MODE (MP3, JPEG)] (page 50)
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE) or both (AUTO)
to be played when playing a DATA CD/DATA DVD.
* Except for United Kingdom and North American models.
**These items are not displayed when playing a DATA CD/DATA DVD with DivX video file (except for United
Kingdom and North American models).
Tip
• The Control Menu icon indicator lights up in green
([PROGRAM], [SHUFFLE], [REPEAT], and [A/V SYNC] only). The [ORIGINAL/PLAY LIST] indicator lights
up in green when you select [PLAY LIST] (default setting).
t
when you select any item except [OFF]
GB
97
Download from Www.Somanuals.com. All Manuals Search And Download.
DVD Setup Display List
You can set the following items with the DVD Setup Display.
The order of the displayed items may be different from the actual display.
LANGUAGE SETUP
OSD1)
CUSTOM SETUP
HDMI
OFF
CONTROL
ON
MENU1)
AUDIO1)
SUBTITLE1)
PAUSE
MODE
TRACK
AUTO
FRAME
OFF
SELECTION AUTO
MULTI-DISC
RESUME
ON
OFF
AUDIO DRC
OFF
STANDARD
MAX
AUDIO
(HDMI)
DivX4)
OFF
ON
SCREEN SETUP
SPEAKER SETUP
TV TYPE
CONNECTION
FRONT
CENTER
YES
YES
NONE
16:9
4:3 LETTER
BOX
4:3 PAN SCAN
SURROUND YES
YCB
C
R
NONE
YCBCR/RGB (HDMI)
RGB
SUBWOOFER YES
AUTO
PAL
NTSC
COLOR
SYSTEM
(VIDEO CD)2)
DISTANCE
(FRONT)
L
3 ft – 23 ft/0.9 m – 6.9 m5)
1.0 m – 7.0 m4)
3 ft – 23 ft/0.9 m – 6.9 m5)
R
1.0 m – 7.0 m4)
ON
OFF
JACKET
PICTURE
GRAPHICS
BLUE
BLACK
ON
OFF
OFF
ON
SCREEN
SAVER
BACKGROUND
0 ft – 23 ft/0.0 m – 6.9 m5)
0.0 m – 7.0 m4)
CENTER
DISTANCE
(SURROUND)
L
0 ft – 23 ft/0.0 m – 6.9 m5)
0.0 m – 7.0 m4)
0 ft – 23 ft/0.0 m – 6.9 m5)
0.0 m – 7.0 m4)
R
BLACK LEVEL3)
–6.0 dB – 0.0 dB
–6.0 dB – 0.0 dB
–6.0 dB – +6.0 dB
–6.0 dB – +6.0 dB
L
R
LEVEL
(FRONT)
CENTER
SUBWOOFER
BLACK LEVEL
(COMPONENT
OUT)3)
LEVEL
(SURROUND)
L
R
–6.0 dB – +6.0 dB
–6.0 dB – +6.0 dB
FULL
4:3 OUTPUT
NORMAL
OFF
ON
TEST TONE
1)Select the language you want to use from the displayed language list.
2)Asian, Australian, and Middle Eastern models only.
3)North American, Mexican, and Latin American models only.
4)Except for North American models.
5)North American models only.
GB
98
Download from Www.Somanuals.com. All Manuals Search And Download.
System Menu List
You can set the following items with SYSTEM MENU on the remote.
System menu
MEMORY1)
FM MODE2)
MEMORY 1-20 (FM), MEMORY 1-10 (AM)
STEREO
MONO
NAME IN1)
SLEEP
SLEEP OFF, SLEEP 90M-1M
DIMMER
DIMMER OFF
DIMMER ON
ILLUM ON
ILLUM OFF
DEMO ON
ILLUM MODE
DEMO
DEMO OFF
ATTENUATE3)
SL SR REV4)
CHILD LOCK
ATT ON
ATT OFF
REV OFF
REV ON
OFF
ON
1)Appears during “TUNER FM” or “TUNER AM” only.
2)Appears during “TUNER FM” only.
3)“ATTENUATE” may not appear, depending on the selected function.
4)Appears when the wireless kit WAHT-SD1 is installed.
GB
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Digital Direct Twin Drive
Subwoofer 87
Numerics
J
16:9 72
4:3 LETTER BOX 72
4:3 PAN SCAN 72
L
Listening
A
M
E
B
F
BLACK LEVEL
(COMPONENT OUT) 74
N
C
O
Other component connection
24
COLOR SYSTEM (VIDEO
CD) 73
COMPONENT VIDEO OUT
22
CUSTOM PARENTAL
CONTROL 63
H
P
HDMI
PCM (Pulse Code Modulation)
89
I
D
Installing the speakers on a wall
19
GB
100
Download from Www.Somanuals.com. All Manuals Search And Download.
R
S
T
U
V
GB
101
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
ALPHABETICAL ORDER
BUTTON DESCRIPTIONS
A – O
P – Z
C/X/x/c/
REPLAY/
/
63)
* The H, number 5, and
VOLUME + buttons have
tactile dots. Use the tactile dots
as references when operating
the system.
Download from Www.Somanuals.com. All Manuals Search And Download.
(1)
Sony Corporation Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|