N Operating the system
2 Place the new ear pad around the
housing.
Listening to a
program
Before listening
Dual Channel
• The transmitter for the headphones is on
the display monitor.
• To prevent your ears from being
damaged, first lower the volume.
Cordless Headphones
Operating Instructions
Käyttöohjeet
N
Additional information
1 Turn on the display monitor.
Precautions
• The driver must not use the headphones.
It may lead to distraction and cause an
accident.
2 Set the power switch to ON on the
left housing of the headphones.
The headphones turn on and the
POWER indicator glows red.
• If the headphones are used while
exposed to direct sunlight, sensitivity of
the infrared sensors may deteriorate, and
inferior quality sound may result.
MV-02HP
© 2005 Sony Corporation
• When the headphones are not to be
used for a long period of time, remove
the batteries to avoid damage caused
by battery leakage and subsequent
corrosion.
Power (ON/OFF) switch
POWER indicator
• Do not leave the headphones in a
location subject to direct sunlight, heat
or moisture (It is recommended to use
the headphones at a of temperature of
between 5 °C and 35 °C).
3 Put on the headphones.
Be sure to put the right housing (R) on
your right ear and the left housing (L)
on your left ear.
• Do not drop, hit or otherwise subject the
headphones to excessive shock of any
kind, as this could damage the product.
4 Start playback.
5 Turn the VOL control dial to adjust
the volume.
If the infrared sensors of the headphones
are covered by your hands when
adjusting the volume, the attenuate
function will be activated and volume
cannot be adjusted. To adjust the
volume, move closer to the transmitter
of the monitor, or orient the infrared
emitters towards the transmitter of the
monitor.
Notes on headphones
preventing hearing damage
Avoid using headphones at high volume.
Hearing experts advise against continuous,
loud and extended play. If you experience
a ringing in your ears, lower the volume or
discontinue use.
Caring for others
Keep the volume at a moderate level. This
will allow you to hear outside sounds and
to be considerate to the people around you.
VOL control dial
If you have any questions or problems
concerning the headphones that are not
covered in this manual, please consult your
nearest Sony dealer.
English
2 Insert size R6 dry batteries into the
battery compartment, matching
the battery 3 terminals with the
3 marks in the compartment.
Sound is automatically attenuated if
noise increases
WARNING
— Attenuate function
To prevent fire or shock hazard,
do not expose the unit to rain or
moisture.
If the infrared rays are obstructed, or
the headphones are used outside their
effective range, noise will increase and
sound will diminish. To avoid potential
ear damage as a result of noise, this
function attenuates any sound in the
headphones. Sound is auto-matically
restored when you move nearer to the
transmitter or remove the obstruction.
Troubleshooting
No sound/Muffled sound
, Turn on the display monitor first, and then
put on the headphones.
, Check that the display monitor is turned
on.
, The attenuate function is activated.
• Check if there is any object between the
transmitter and the headphones.
• Use the headphones near the transmitter.
, The headphones’ power indicator light
dims, flashes or goes off.
Welcome!
Thank you for purchasing the Sony MV-
02HP Dual Channel Cordless Headphones.
Before operating the unit, please read this
manual thoroughly and retain it for future
reference.
3 Close the battery compartment lid.
Selecting the audio channel
You can select the audio channel with the
CH1/CH2 switch to avoid interference
when using the cordless headphones with
other AV equipment. Select the audio
channel according to the Mobile Monitor
XVM-F65 setting of “WireLess Headphone.”
The MV-02HP is a cordless stereo head-
phone using infrared transmission. You
can enjoy listening to a programme free
from the restriction of the headphone cord.
• Replace the batteries with new ones.
Distorted sound
, The headphones’ power indicator light
• Cordless, noiseless infrared headphone
resistant to external noise, etc.
• Self-adjusting headband mechanism
eliminating the need for headband
adjustment.
• Single VOL control adjusts both the right
and left volume of the headphones.
• Use with car monitors with built-in
infrared transmitter.
dims, flashes or goes off.
• Replace the batteries with new ones.
After listening to the programmes
Battery life
Battery
Sony alkaline battery
LR6/AM-3 (N)
Sony manganese
battery R6/SUM-3
(NU)
Approx. hours*1
Take off the headphones, and then turn
off the power (Noise may occur if you
turn off the monitor before taking off the
headphones).
90 hours*2
Loud background noise
40 hours*2
, Move closer to the transmitter. (As you
move away from the transmitter, more
noise is likely to be heard. This is inherent
in infrared ray transmission and does
not mean that there is a problem with the
headphones.)
, Check that there are no objects between the
transmitter and the headphones.
, Check that the infrared sensors are not
obstructed by your hands or hair.
, Use the headphones away from direct
sunlight.
*1 at 1 kHz, 1 mW+1 mW output
*2 Time stated above may vary, depending on
the temperature or conditions of use.
Replacing the ear
pads
The ear pads are replaceable. If the ear
pads become dirty or worn out, replace
them as illustrated below.
The ear pad is not commercially available.
You can order replacements at your
nearest Sony dealer.
N Getting started
Notes on Batteries
• Do not attempt to charge dry batteries.
• Do not carry batteries together with
coins or other metallic objects. Heat can
be generated if the positive and negative
terminals accidentally come into contact
with metallic objects.
• If you are not going to use the unit for a
long time, remove the batteries to avoid
damage from battery leakage or corrosion.
Inserting the
batteries
, The headphones’ power indicator light
dims, flashes or goes off.
1 Open the battery compartment lid
• Replace the batteries with new ones.
v
(
) of the left housing.
1 Remove the old ear pad by pulling
it off.
When to replace the batteries
v
Lid (
)
When the batteries become weak, the
power indicator light dims, or sound
becomes distorted or noisy. Replace the
batteries with new ones as soon as possible.
Ear pad
(Continue to next page)
Download from Www.Somanuals.com. All Manuals Search And Download.
|