FLAT WIDE DISPLAY MONITOR
FWD-S47H1/S42H1
PROTOCOL MANUAL (For Customer)
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1
RS-232C
1. Communication Parameters
Communication method
Synchronous method
Baud rate
RS-232C
Asynchronous
9600bps
8bit
Character length
Parity
None
Start bit length
Stop bit length
Flow control
ꢀbit
ꢀbit
None
2. Pin Assignment
Monitor side (D-sub 9-pin)
Host side (D-sub 9-pin)
5
4
3
2
1
5
4
3
2
1
9
8
7
6
9
8
7
6
_ External view _
_ External view _
Pin No. Function
Pin No. Function
1
2
3
4
5
6
7
8
9
NC
TXD
RXD
NC
1
2
3
4
5
6
7
8
9
NC
RXD
TXD
NC
GND
NC
GND
NC
NC
NC
NC
NC
NC
NC
3. Communication Data Format
(a) Control message
No.
Item
Value
ꢀ
Header
0x8C: Control
0xXX
2
Category
Function
Dataꢀ (Length)
Data2 (Dataꢀ)
:
3
0xXX
4
0xXX
5
0xXX
:
0xXX
:
:
0xXX
X
DataX
0xXX
X+ꢀ
Check Sum
0xXX
* Check Sum: Sum total of ꢀ to X. Lower one-byte data is validated when a value exceeds 255 (ꢀbyte).
* Set the command interval to 500 ms or more when transmitting the Control command continuously.
* Set the command interval to 500 ms or more when transmitting the same command (Enquiry) after the Control command.
FWD-S42Hꢀ
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
(b) Enquiry message
No.
Item
Value
ꢀ
2
3
4
5
6
Header
0x83: Enquiry
0xXX
Category
Function
Dataꢀ
0xXX
0xFF
Data2
0xFF
Check Sum
0xXX
* Check Sum: Sum total of ꢀ to X, lower one-byte data is validated when a value exceeds 255 (ꢀbyte).
(c) Answer message
1 Control answer
No.
Item
Value
ꢀ
2
Header
Answer*
0x70: Answer
0x00: Completed
0x0ꢀ: Limit Over
0x02: Limit Under
0x03: Command Canceled
0xXX
3
Check Sum
* 0x00: Completed
0x0ꢀ: Limit Over
Packet is correctly received and process is also correctly completed.
Packet is correctly received, but the data value is over the upper limit.
0x02: Limit Under
0x03: Command Canceled
* Check Sum:
Packet is correctly received, but the data value under the lower limit.
Packet is correctly received, but the data value is not correct or the request cannot be accepted in the current host state.
Sum total of ꢀ to X, lower one-byte data is validated when a value exceeds 255 (ꢀbyte).
2 Enquiry answer (Complete)
No.
Item
Value
ꢀ
Header
0x70: Answer
0x00: Completed
0xXX
2
Answer
3
Return Data Size
Return Dataꢀ
:
4
0xXX
:
0xXX
:
:
0xXX
X
Return DataX
Check Sum
0xXX
X+ꢀ
0xXX
* 0x00: Completed
* Return Data:
* Check Sum:
Packet is correctly received and process is also correctly completed.
Returns the read value.
Sum total of ꢀ to X, lower one-byte data is validated when a value exceeds 255 (ꢀbyte).
3 Enquiry answer (Command cancel)
No.
Item
Value
ꢀ
2
3
Header
0x70: Answer
Answer
0x03: Command Canceled
Check Sum
0x73
0x03: Command Canceled
Packet is correctly received, but the data value is not correct or the request cannot be accepted in the current host state.
FWD-S42Hꢀ
2
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Error answer
No.
Item
Value
ꢀ
2
Header
Answer*
0xE0: Answer
0x00: No Function Error
0x0ꢀ: Check Sum Error
0x02: Data Length Error
0xXX
3
Check Sum
* 0x00: No Function Error
0x0ꢀ: Check Sum Error
0x02: Data Length Error
Packet header,category or function code are not included in this protocol.
Check sum value of received packet is not correct.
The data size of received packet is not correct.
4. General Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0x00
Code Table (ꢀ-a) [a]
0x02
0xFF
Code Table (ꢀ-a) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (ꢀ-a) [b]
0xXX
Completed
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x00
0x0ꢀ
Power
0x00 OFF
Yes
Yes
Enable
Enable
0x0ꢀ ON
Input Select*ꢀ
0x08 HDꢀ5 RGB
0x09 HDꢀ5 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
Yes
Yes
Disable
Enable
0x30 VIDEO
0x3ꢀ S-VIDEO
0x84 Option Digitalꢀ (HDMIꢀ/SDI)
0x85 Option Digital2 (HDMI2)
0x02
0x03
0x04
Force Status Display 0x00 ON
0x0ꢀ OFF
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
Enable
Enable
Audio Mute
0x00 OFF
0x0ꢀ ON
0x00 ON
0x0ꢀ OFF
Auto Status Display
(Continued)
FWD-S42Hꢀ
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x06
Color System
0x00 Auto
Yes
Yes
Disable
Enable
0x0ꢀ NTSC
0x02 NTSC4.43
0x03 PAL
0x05 PAL-M
0x06 PAL-N
0x07 PAL60
0x0F
Language
0x00 Japanese
0x0ꢀ English
0x02 Deutsch
0x03 Français
0x04 Español
0x05 Italiano
0x0ꢀ-0xFF
Yes
Yes
Disable
Enable
0xꢀ0
0xꢀ2
Index Number
Standby Power
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x00 Standard
0x0ꢀ Low
0xꢀ3
ECO Mode
(Power Saving)
0x00 Off
Yes
Yes
Disable
Enable
0x0ꢀ ECO High
0x02 ECO Low
0x00 ON
0xꢀ4
0xꢀ8
0xꢀB
0x24
Speaker Out
Sync Mode
Yes
Yes
Yes
No
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
0x0ꢀ OFF
0x00 H/Comp
0x0ꢀ Video
Clock Display
0x00 OFF
0x0ꢀ ON
Input Detect
(Option)
0x00 FWꢀ2 (HDꢀ5)
0x02 FWꢀꢀ (BNC)
0x03 Reserved
0x05 FW50 (RGB)
0x06 FW2ꢀ (UART + CTRL-S)
0x08 FWꢀ5 (HDMI x 2)
0x09 FWꢀ6 (HD-SDI)
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
(Continued)
FWD-S42Hꢀ
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x26
0x27
0x30
Auto Shut OFF
0x00 OFF
Yes
Yes
Yes
Yes
Disable
Enable
0x0ꢀ ON
Auto Screen Adjust
PAP
0x00 OFF
Yes
Yes
Disable
Disable
Enable
Enable
0x0ꢀ ON
0x00 OFF
0x0ꢀ P&P
0x02 PinP
0x3ꢀ
Active Picture
0x00 Left (P&P)/Main (PinP)
0x0ꢀ Right (P&P)/Sub (PinP)
0x02 Swap
Yes
Yes
Disable
Enable
0x32
0x33
Picture Size (P&P)
0x00-0x0E
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
Sub Picture Size
(PinP)
0x00 Large
0x0ꢀ Small
0x34
Picture Position
(PinP)
0x00 Positionꢀ
Yes
Yes
Disable
Enable
0x0ꢀ Position2
0x02 Position3
0x03 Position4
0x35
PAP Input Detect
(Left/Main)
0x08 HDꢀ5 RGB
0x09 HDꢀ5 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
No
Yes
Disable
Enable
0x30 VIDEO
0x3ꢀ S-VIDEO
0x84 Option Digitalꢀ (HDMIꢀ/SDI)
0x85 Option Digital2 (HDMI2)
0x08 HDꢀ5 RGB
0x09 HDꢀ5 YUV
0x0E OPTION RGB
0x0F OPTION COMPONENT
0x20 DVI
0x36
PAP Input Detect
(Right/Sub)
No
Yes
Disable
Enable
0x30 VIDEO
0x3ꢀ S-VIDEO
0x84 Option Digitalꢀ (HDMIꢀ/SDI)
0x85 Option Digital2 (HDMI2)
(Continued)
FWD-S42Hꢀ
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Control
Command
Enquiry
Standby
Power On
0x40
Screen Saver
0x00 OFF
Yes
Yes
Disable
Enable
0x0ꢀ All White ON
0x02 Sweep ON
0x03 Standby
0x43
0x44
Back Light
0x00-0x64
Yes
Yes
Yes
Yes
Disable
Enable
Enable
Enable
Logo Illumination
0x00 Logo Off
0x0ꢀ Logo On (Low)
0x02 Logo On (High)
0x00 Main + Remocon
0x0ꢀ Main
0x45
Control Mode
Yes
Yes
Disable
Enable
0x02 Remocon
0x03 All Off
0x04 Limited*2
0x46
0x47
On Off Timer Mode
On Timer Enable
0x00 Every Day (Repeat)
0x0ꢀ Day Of Week
Yes
Yes
Yes
Enable
Enable
Enable
Enable
bit0
bitꢀ
bit2
bit3
bit4
bit5
bit6
bit7
bit0
bitꢀ
bit2
bit3
bit4
bit5
bit6
bit7
Sunday ꢀ: Enable, 0: Disable Yes
Monday ꢀ: Enable, 0: Disable
Tuesday ꢀ: Enable, 0: Disable
Wednesday ꢀ: Enable, 0: Disable
Thursday ꢀ: Enable, 0: Disable
Friday ꢀ: Enable, 0: Disable
Saturday ꢀ: Enable, 0: Disable
Every day ꢀ: Enable, 0: Disable
0x48
Off Timer Enable
Sunday ꢀ: Enable, 0: Disable Yes
Monday ꢀ: Enable, 0: Disable
Tuesday ꢀ: Enable, 0: Disable
Wednesday ꢀ: Enable, 0: Disable
Thursday ꢀ: Enable, 0: Disable
Friday ꢀ: Enable, 0: Disable
Yes
Enable
Enable
Saturday ꢀ: Enable, 0: Disable
Every day ꢀ: Enable, 0: Disable
0x65
0x66
IP Setting Mode
0x00 DHCP
Yes
No
Yes
Yes
Enable
Enable
Enable
Enable
0x0ꢀ Manual
0x02 Speed
IP Setting Execute
0x00 Shut Down
0x0ꢀ IP Setting
0x02 NVR Reset
0x03 Alarm
0x04 LAN FW version
(Continued)
FWD-S42Hꢀ
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x67
IP Setting Result
0x00 Done
Yes
No
Enable
Enable
0x0ꢀ Error ꢀ (UART Commu.)
0x02 Error 2 (Duplication)
0x03 Error 3 (IP Add Setting)
0x04 Error 4 (GW Add setting)
0x05 Error 5 (DNSꢀ Setting)
0x06 Error 6 (DNS2 Setting)
0x07 Error 7 (Sbnt Msk Setting)
0x00 ꢀ00Mbps/Full Duplex
0x0ꢀ ꢀ00Mbps/Half Duplex
0x02 ꢀ0Mbps/Full Duplex
0x03 ꢀ0Mbps/Half Duplex
0x04 Auto
0x68
0x70
Speed Setting
Yes
Yes
Yes
Yes
Enable
Disable
Enable
Enable
Input Skip
bit0
bitꢀ
bit2
bit3
bit4
bit5
bit6
bit7
HDꢀ5
DVI
Reserved
VIDEO
S-VIDEO
Reserved
Reserved
Reserved
0x7ꢀ
0x74
0x75
0x76
0x7A
Default Input
0x00 Last Memory
0x0ꢀ Option
Yes
No
Yes
Yes
Yes
Yes
Yes
Enable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
Enable
Digital Signal Detect 0x00 VIDEO
*3
(DVI/HDMI/etc.)
Signal Status*4
0x0ꢀ PC
0x00 Stable
No
0x0ꢀ Unstable/No Signal
VIDEO Signal Detect 0x00 NTSC
0x0ꢀ PAL
No
Logo Position
0x00 Auto
Yes
0x0ꢀ Landscape
0x02 Portrait
0x7D
Power Management 0x00 OFF
Mode*5
0x0ꢀ ON
Yes
Yes
Disable
Enable
FWD-S42Hꢀ
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
0x7E
On Screen Logo
0x00 OFF
Yes
Yes
Enable
Enable
0x0ꢀ ON (Default)
0x02 Reserved
0x00 OFF
0x7F
0x8ꢀ
LED
Yes
Yes
Yes
Yes
Disable
Enable
Enable
Enable
0x0ꢀ ON
Power On Delay
0x00-0x78 ꢀsec x Data
*ꢀ: Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable.
*2: Restricts a part of keys operation following below.
[Remote Commander]
Menu, Picture, Sound, ECO (Power Saving), Contrast+/_,Brightness, Chroma, H Shift, V Shift, V size, PAP
[Main]
Menu
*3: Digital Signal Status is Enable for Digital Input Signal Detect Function only in Stable.
*4: Digital Signal or VIDEO Signal is Enable. Return Signal Status of Active Window.
*5: Only the panel power supply is turned off at the standby when setting it “ON”.
5. Analog Signal Detect Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (ꢀ-a) [a]
Code Table (ꢀ-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (ꢀ-a) [b]
0xFF
0xXX Completed
Code Table (1-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Yes
Standby
Disable
Power On
0x78
Analog Signal Detect 0x00 VIDEO
0x0ꢀ PC
No
Enable
Code Table (1-d)
Input Select
0x00
0x0ꢀ
0xFF
Main
1-a[b]
Sub
When input is no signal or not supported signal, return value become Video(0x00).
Present input
FWD-S42Hꢀ
8
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Priority Signal Select Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (2-a) [a]
Code Table (2-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (2-a) [b]
0xFF
0xXX Completed
Code Table (2-a)
[a]Function
[b]Range/Switch Code
Command
Control
Enquiry
Yes
Standby
Disable
Power On
0x77
Priority Signal Select 0x00 Inputꢀ Auto
0x0ꢀ Inputꢀ RGB
No
Enable
0x02 Inputꢀ YPbPr
Code Table (2-d)
Input Select
0x00
0x0ꢀ
HDꢀ5
Option
(b) Time Control
Data Set (Month, Date)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x7C
0x03
Month: 0x0ꢀ-0x0C
Date: 0x0ꢀ-0xꢀF 0xXX
Syntax
Header
Category
Function
Data1
Data2
0xFF
Check Sum
0xFD
Enquiry
0x83
0x00
0x7C
0xFF
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x03
Month: 0x00-0x0C Date: 0x0ꢀ-0xꢀF 0xXX Completed
FWD-S42Hꢀ
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Year Set
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
0x7B
0x02
Year: 0x00-0x63
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x7B
0xFF
0xFF
0xFC
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x02
Year: 0x00-0x63
0xXX
Completed
Clock Set (Hour, Minute)
Syntax
Header
Category
Function
Data1
Data2
Hour: 0x00-0xꢀ7
Data3
Check Sum
Control
0x8C
0x00
0x22
0x03
Minute: 0x00-0x3B 0xXX
Syntax
Header
Category
Function
Data1
Data2
0xFF
Check Sum
Enquiry
0x83
0x00
0x22
0xFF
0xA3
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size Return Data1
0x03
Return Data2
Check Sum
Enquiry
0x70
Hour: *0x00-0xꢀ7 Minute: 0x00-0x3B 0xXX
Completed
Clock Set (Week)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x23
0xFF
0xFF
0xA4
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
0xXX
Enquiry
0x70
0x00
0x02
Week: Code Table (ꢀ-e)
Completed
FWD-S42Hꢀ
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (1-e)
Week Select
0x00
0x0ꢀ
0x02
0x03
0x04
0x05
0x06
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
On Timer, Off Timer
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
Code Table (ꢀ-f) [a]
0x03
Hour: 0x00-0xꢀ7
Minute: 0x00-0x3B 0xXX
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (ꢀ-f) [a]
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x03
Hour: 0x00-0xꢀ7
Minute: 0x00-0x3B
0xXX
Completed
Code Table (1-f)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
On Timer
0x50
Sunday
_
_
_
_
_
_
_
_
Yes
Yes
Disable
Enable
0x5ꢀ
0x52
0x53
0x54
0x55
0x56
0x57
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Every day
Off Timer
0x58
Sunday
_
_
_
Yes
Yes
Disable
Enable
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
Monday
Tuesday
Wednesday
Thursday
Friday
_
_
_
Saturday
Every day
_
_
FWD-S42Hꢀ
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
(d) IP Address Setting
IP Address
Syntax Header
Category Function Data1
0x00 0x42 0x05
Data2
Data3
Data4
Data5
Check Sum
Control 0x8C
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
Syntax Header
Category Function Data1
0x00 0x42 0xFF
Data2
Check Sum
Enquiry 0x83
0xFF
0xC3
Subnet Mask
Syntax Header
Category Function Data1
0x00 0x6ꢀ 0x05
Data2
Data3
Data4
Data5
Check Sum
Control 0x8C
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
Syntax Header
Category Function Data1
0x00 0x6ꢀ 0xFF
Data2
Check Sum
Enquiry 0x83
0xFF
0xE2
Gateway Address
Syntax Header
Category Function Data1
0x00 0x62 0x05
Data2
Data3
Data4
Data5
Check Sum
Control 0x8C
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
Syntax Header
Category Function Data1
0x00 0x62 0xFF
Data2
Check Sum
Enquiry 0x83
0xFF
0xE3
DNS Primary
Syntax Header
Category Function Data1
0x00 0x63 0x05
Data2
Data3
Data4
Data5
Check Sum
Control 0x8C
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
Syntax Header
Category Function Data1
0x00 0x63 0xFF
Data2
Check Sum
Enquiry 0x83
0xFF
0xE4
DNS Secondary
Syntax Header
Category Function Data1
0x00 0x64 0x05
Data2
Data3
Data4
Data5
Check Sum
Control 0x8C
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
Syntax Header
Category Function Data1
0x00 0x64 0xFF
Data2
Check Sum
Enquiry 0x83
0xFF
0xE5
FWD-S42Hꢀ
ꢀ2
Download from Www.Somanuals.com. All Manuals Search And Download.
Player IP Address
Syntax Header
Category Function Data1
Data2
Check Sum
Enquiry 0x83
0x00
0x83
0xFF
0xFF
0x04
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Answer Header Category Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Enquiry 0x8C
0x00
Code Table 0x05
(ꢀ-a)[a]
Address 0
0x00-0xFF
Address ꢀ
0x00-0xFF
Address 2
0x00-0xFF 0x00-0xFF
Address 3
0xXX
IP Address ex)
ꢀ92.ꢀ28.ꢀ4.ꢀ
→
ꢀ92 (0xC0) Address 0
ꢀ28 (0x80) Address ꢀ
ꢀ4 (0x0E) Address 2
ꢀ
(0x0ꢀ) Address 3
* IP address command can be carried out even in the standby state.
Code Table (1-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x42 IP Address
_
_
_
_
_
_
Enable
Enable
Enable
Enable
0x6ꢀ Subnet Mask
0x62 Gateway Address
0x63 DNS Primary
0x64 DNS Secondary
0x83 IP Address (Player)
Disable
Enable
Enable
Enable
7. Picture/Sound
(a) Picture/Sound
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0xꢀ0
Code Table (2-a) [a]
0x02
0xFF
Code Table (2-a) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x02
Code Table (2-a) [b]
0xXX
Completed
FWD-S42Hꢀ
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
0x0ꢀ
0x02
0x03
0x04
Contrast
Brightness
Chroma
0x00-0x64
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
0x00-0x64
0x00-0x32
Phase
0x00-0x64
Color Temp
0x00 Cool
0x0ꢀ Neutral
0x02 Warm
0x03 Custom
0x00-0xꢀ4
0x09
0x0A
Sharpness
NR
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x00 OFF
0x0ꢀ Low
0x02 Mid
0x03 High
0x00 Auto
0x0ꢀ OFF
0x00 OFF
0x0ꢀ ON
0x0B
0x0C
Cinema Drive
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
Dynamic Picture
0x02 Reserve
0x00 ON
0x0D
0x0E
Color Correct
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x0ꢀ OFF
0x00 High
0x0ꢀ Mid
Gamma Correct
0x02 Low
0x03 Option
0x00 Standard
0x0ꢀ Vivid
0x02 Custom
0x05 TC Control
0x06 Conference
0x00 ON
0xꢀ0
Picture Mode
Yes
Yes
Disable
Enable
0xꢀꢀ
Brightness Boost*ꢀ
Yes
Yes
Disable
Enable
0x0ꢀ OFF
0x00-0x64
0x30
0x3ꢀ
0x32
0x33
0x34
Volume
Treble*2
Bass*2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Enable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
0x00-0x64
0x00-0x64
Balance
Surround
0x00-0x64
0x00 OFF
0x0ꢀ Hall
0x02 Simulate
0x00 Dynamic
0x0ꢀ Standard
0x02 Reserve
0x03 Custom
0x35
Sound Mode
Yes
Yes
Disable
Enable
(Continued)
FWD-S42Hꢀ
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x36
0x37
Default Volume Set
0x00-0x64
Yes
Yes
Yes
Yes
Enable
Enable
Enable
Enable
Volume Select
0x00 Last Memory
0x0ꢀ Default Setting
0x32 50
0x38
Max Volume Set
Yes
Yes
Enable
Enable
0x46 70
0x64 ꢀ00
*ꢀ Picture Mode = Vivid Only is Enabled.
*2 Sound Mode = Custom Only is Enabled.
(c) Color Temp
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0xꢀ0
Code Table (2-b) [a]
0x03
Code Table (2-c) Code Table (2-b) [b]
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0xꢀ0
Code Table (2-b) [a]
Code Table (2-c) 0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x03
Code Table (2-c) Code Table (2-b) [b]
0xXX
Completed
Code Table (2-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x05
0x06
0x07
Red Gain
Green Gain
Blue Gain
0x00-0xꢀE
Yes
Yes
Disable
Enable
Code Table (2-c)
Format Select
0x00
0x0ꢀ
0x02
0x03
Cool
Neutral
Warm
Custom
FWD-S42Hꢀ
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Size/Shift
(a) 8Bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
Enquiry
0x8C
0x83
0x20
Code Table (3-b) [a]
0x02
0xFF
Code Table (3-b) [b]
0xFF
0xXX
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
0x00
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x02
Code Table (3-b) [b]
0xXX
Completed
Code Table (3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
0x0ꢀ
0x02
0x03
0x04
H Size
H Shift
V Size
V Shift
Aspect
0x00-0x3C
0x00-0x3C
0x00-0x3C
0x00-0x3C
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Disable
Disable
Disable
Disable
Disable
Enable
Enable
Enable
Enable
Enable
0x00 Wide Zoom
(VIDEO Only)
0x0ꢀ Zoom
(VIDEO Only)
0x02 Full
(VIDEO Only)
0x04 Normal
(PC:Real, VIDEO: 4:3)
0x05 Full ꢀ (PC Only)
0x06 Full 2 (PC Only)
0x00 OFF
0x05
Multi Display
Yes
Yes
Disable
Enable
0x0ꢀ 2 x 2
0x02 3 x 3
0x03 4 x 4
0x04 ꢀ x 2
0x05 ꢀ x 3
0x06 ꢀ x 4
0x07 2 x ꢀ
0x08 3 x ꢀ
0x09 4 x ꢀ
(Continued)
FWD-S42Hꢀ
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Table (3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x06
0x07
0x0B
Auto Pixel Adjust
0xFF Execute
0x00-0xꢀF
Yes
Yes
Yes
No
Disable
Disable
Disable
Enable
Enable
Enable
Dot Phase
Yes
Yes
Multi Position
0x00 Positionꢀ
(2 x 2 ,ꢀ x 2, 2 x ꢀ)*ꢀ 0x0ꢀ Position2
0x02 Position3
0x03 Position4
0x0C
Multi Position
0x00 Positionꢀ
Yes
Yes
Disable
Enable
(3 x 3, ꢀ x 3, 3 x ꢀ)*ꢀ 0x0ꢀ Position2
0x02 Position3
0x03 Position4
0x04 Position5
0x05 Position6
0x06 Position7
0x07 Position8
0x08 Position9
0x0D
Multi Position
0x00 Positionꢀ
Yes
Yes
Disable
Enable
(4 x 4, ꢀ x 4, 4 x ꢀ)*ꢀ 0x0ꢀ Position2
0x02 Position3
0x03 Position4
0x04 Position5
0x05 Position6
0x06 Position7
0x07 Position8
0x08 Position9
0x09 Positionꢀ0
0x0A Positionꢀꢀ
0x0B Positionꢀ2
0x0C Positionꢀ3
0x0D Positionꢀ4
0x0E Positionꢀ5
0x0F Positionꢀ6
0x0E
0x0F
Over Scan
0x00 OFF
0x0ꢀ ON
Yes
Yes
Yes
Yes
Disable
Disable
Enable
Enable
0x02 AUTO
0x00 Tiles
0x0ꢀ Window
Multi Display
Output Format
FWD-S42Hꢀ
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
*1 Arrangement of Multi Position.
Multi Position (2 x 2)
Multi Position (1 x 2)
Multi Position (2 x 1)
1
3
2
4
1
2
1
2
Multi Position (3 x 3)
Multi Position (1 x 3)
Multi Position (3 x 1)
1
4
7
2
5
8
3
6
9
1
2
3
1
2
3
Multi Position (4 x 4)
Multi Position (1 x 4)
Multi Position (4 x 1)
1
5
9
2
6
3
7
4
8
1
2
3
4
1
2
3
4
10 11 12
13 14 15 16
FWD-S42Hꢀ
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
(b) Power On Batch
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x85
0x03
Input Select Code
Table (ꢀ-a)[a]
Volume Code
Table (ꢀ-a)[b]
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x85
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x70
0x70
0x00
0x0ꢀ
0x02
0x03
0x70
0x7ꢀ
0x72
0x73
Completed
Limit Over
Limit Under
Command Canceled
Answer
Header
Answer
Return to Data Size
Data2
Data3
Check Sum
Enquiry
0x70
0x00
0x03
Input Select Code
Table (ꢀ-a)[a]
Volume Code
Table (ꢀ-a)[b]
0xXX
Code Table (1-a)
Input Select [a]*2 0x08
HDꢀ5 RGB
0x09
0x0E
0x0F
0x20
0x30
0x3ꢀ
0x84
0x85
HDꢀ5 YUV
Option RGB
Option COMPONENT
DVI
VIDEO
S-VIDEO
Option Digitalꢀ (HDMIꢀ/SDI)
Option Digital2 (HDMI2)
Volume [b]
0x00-0x64
Code Table (1-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x85
Power On Batch
Yes
No
Enable
Control/Disable
*1 When this control command is received, the power of a set will be turned on first.
*2 Input Select setting, Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable.
FWD-S42Hꢀ
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Status Enquiry
(a) Model Name
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x00
0xFF
0xFF
0xBꢀ
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-a)
0xXX
Completed
Code Table (4-a)
Format Select
0x28
0x29
FWD-S42Hꢀ
FWD-S47Hꢀ
(b) Serial Number
Syntax
Header
Category
Function
Data1
0xFF
Data2
Check Sum
Enquiry
0x83
0x30
0x0ꢀ
0xFF
0xB2
Answer Header Answer Return to Return Data1 Return Data2 Return Data3 Return Data4 Check Sum
Data Size
Enquiry 0x70
0x00
0x05
Upper 8bit
Data
Middle Upper Middle Lower Lower 8bit
0xXX
Completed
Data
Data
Data
Return Dataꢀ-Data4: 0x00000000-0x0098967F (0,000,000-9,999,999)
(c) Operation Time
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x02
0xFF
0xFF
0xB3
Answer Header Answer Return to Return Data1 Return Data2 Return Data3 Return Data4 Check Sum
Data Size
Enquiry 0x70
0x00
0x05
Upper 8bit
Data
Middle Upper Middle Lower Lower 8bit
Data Data Data
0xXX
Completed
Return Dataꢀ-Data4: 0x00000000-0xD693A3FF (0sec.-3,599,999,99sec.)
3,599,999,999 sec
FWD-S42Hꢀ
20
Download from Www.Somanuals.com. All Manuals Search And Download.
(d) Soft Version (Main CPU/LAN)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
Code Table
(4-k)
0xFF
0xFF
0xB4
Answer
Header
Answer
Return to Data Size Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
Code Table
(4-k)
Upper 8bit Data
Lower 8bit Data
0xXX
Completed
Return Dataꢀ-Data2: 0x0000-0xFFFF (BCD Format)
ex) In Version0.ꢀ00, it is set to 0ꢀ and 00.
Code Table (4-k)
Function
Return Data
0x03 Main CPU
0x0F LAN
0x0000-0xFFFF
0x0000-0xFFFF
(e) 8bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
0xXX
Enquiry
0x83
0x30
Code Table (4-b)
0xFF
0xFF
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-b)
0xXX
Completed
Code Table (4-b)*
Function
Return Data
0x00-0xFF
Unit
*
0x07
0x08
0x09
0x0A
0x0B
0x0D
0xꢀꢀ
0xꢀ2
0xꢀ3
0xꢀ4
0xꢀ6
Digital 3.3 V
. For function 0x07, 0x08, 0x09, 0x11, 0x12, 0x13,
0x14 and 0x16 in the left table
When the display value is 3.0 V,“0x1E”(30) is
returned.
Analog 24 V
Digital 5 V
Tempꢀ
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
Temp2
Inverter Alarm
Shutdown Log
0: Normal, ꢀ: Abnormal
0x00-0xFF
. For function 0x0A, 0x0B and 0x0D in the left table
When the display value is 50 dC“, 0x32”(50) is
returned.
When the display value is _20 dC, “0xEC”is re-
turned.
Digital 3.3 V (Failure) 0x00-0xFF
Digital 5 V (Failure) 0x00-0xFF
Analog ꢀ2 V (Failure) 0x00-0xFF
Analog ꢀ2 V 0x00-0xFF
FWD-S42Hꢀ
2ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
(f) Shutdown Log
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0xꢀꢀ
0xFF
0xFF
0xC2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Shutdown Log
0xXX
Completed
Code Table (4-c)
Return Dataꢀ: 0x00-0xFF
(g) Shutdown Log Clear
Syntax
Header
Category
Function
Data1
0x02
Data2
Check Sum
0xCF
Control
0x8C
0x30
0xꢀꢀ
0x00
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
(h) LAN Firmware Version
Syntax
Header
Category
Function
Data1
0x03
Data2
Data3
Check Sum
0xXX
Control
0x8C
0x30
0x0F
Soft Version (LAN)
Upper data
Soft Version (LAN)
Lower data
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Code Table (4-c)
Shutdown Information
bit0 Reserved
bitꢀ ꢀ: FAN Sensor Abnormal
bit2 ꢀ: Panel Temperature Abnormal
bit3 ꢀ: Temperature Sensor Abnormal
bit4 Reserved
0: Normal
0: Normal
0: Normal
bit5 ꢀ: Power Abnormal (3.3 V, 5 V)
0: Normal
0: Normal
bit6 ꢀ: Analog Power Abnormal (ꢀ2 V, 9 V, 24 V)
bit7 Reserved
FWD-S42Hꢀ
22
Download from Www.Somanuals.com. All Manuals Search And Download.
(i) Auto Input Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x30
0xFF
0xFF
0xEꢀ
Answer Header Answer
Return to
Data Size
Return Data1 Return Data2 Return Data3 Return Data4 Return Data5
Enquiry 0x70
0x00
0x0C
Inputꢀ
Input2
Input3
Input4
Input5
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Input Type
Code Table
(4-e)
Return Data6 Return Data7 Return Data8 Return Data9 Return Data10
Optionꢀ
Optionꢀ
Input Type
Code Table
(4-e)
Option2
Option2
Input Type
Code Table
(4-e)
Option3
Option Type
Code Table
(4-e)
Option Type
Code Table
(4-e)
Option Type
Code Table
(4-e)
Return Data11 Check Sum
Option3
Input Type
Code Table
(4-e)
0xXX
Completed
Code Table (4-e)
Input
Input Type (Basic)
Option Type
Input Type (Option)
INPUTꢀ
INPUT2
INPUT3
INPUT4
INPUT5
OPTIONꢀ
0x02
0x0ꢀ
0x06
0x07
0x00
S-Video
Video
RGB/YUV (Analog)
DVI
No Input
0x00 Analog Only
0x00 Analog Only
0x00 Analog Only
0x00 Analog Only
0x0ꢀ Analog/Com
0x03 Com Only
0x00 No Input
0x03 Video/S-Video
0x06 RGB/YUV (Analog)
0x07 Video/S-Video/RGB/YUV (Analog)
0x04 RGB
0x00 No Input
0x04 Digital Only
0x04 Digital Only
0x00 Analog Only
0x00 Analog Only
0x0E Digital/Digital
0x0D Digital
OPTION2
OPTION3
0x00 No Input
0x00 No Input
FWD-S42Hꢀ
23
Download from Www.Somanuals.com. All Manuals Search And Download.
(j) Auto Panel Type Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x3ꢀ
0xFF
0xFF
0xE2
Answer
Header
Answer
Return to Data Size Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-h)
0x72
Completed
Code Table (4-i)
Code Table (4-j)
Code Table (4-h)
H_Resolution
V_Resolution
0x0780 (ꢀ920)
0x0438 (ꢀ080)
Input Quantity
0x05
Panel Type
Option Slot Quantity
0x0ꢀ
0x00
LCD
Code Table (4-d)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Yes
Standby
Power On
0x00 Model Name
0x0ꢀ Serial Number
0x28, 0x29
No
Enable
Enable
0x00000000-0x0098967F
(0,000,000-9,999,999)
0x02 Operation Time
0x00000000-0xD693A3FF
(0sec.-3,599,999,999sec.)
0x03 Soft Version (Main)
0x07 Digital 3.3 V
0x0000-0x9999
0x00-0xFF
0x08 Analog 24 V
0x00-0xFF
0x09 Digital 5 V
0x00-0xFF
0x0A Tempꢀ
0x00-0xFF
0x0B Temp2
0x00-0xFF
0x0C Temp3
0x00-0xFF
0x0D Temp P/S
0x00-0xFF
0x0E Inverter Alarm
0x0F Soft Version (LAN)
0xꢀ0 Analog 9 V
0: Normal, ꢀ: Abnormal
0x0000-0x9999
0x00-0xFF
0xꢀꢀ Shutdown Log
0xꢀ2 Digital 3.3 V (Failure)
0xꢀ3 Digital 5 V (Failure)
0xꢀ4 Analog 9 V (Failure)
0xꢀ6 Analog ꢀ2 V
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x00-0xFF
0x30 Auto Input Detect
0x3ꢀ Auto Panel Type Detect
FWD-S42Hꢀ
24
Download from Www.Somanuals.com. All Manuals Search And Download.
(k) Auto Plug Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x32
0xFF
0xFF
0xE3
Answer Header Answer
Return to Data Size
Return Data1
Return Data2
Return Data3
Enquiry 0x70
0x00
0x2ꢀ
Panel Type
Code Table (4-h)
H_Resolution (H)
Code Table (4-i)
H_Resolution (L)
Code Table (4-i)
Return Data4
Return Data5
Return Data6
Return Data7
V_Resolution (H)
Code Table (4-i)
V_Resolution (L)
Code Table (4-i)
Input Quantity
Code Table (4-j)
Inputꢀ
Input Type
Code Table (4-e)
Return Data8
Return Data9
Return Data10
Return Data11
Input2
Input3
Input4
Input5
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Input Type
Code Table (4-e)
Return Data12
Return Data13
Return Data14
Return Data15
Option Slot Quantity
Code Table (4-j)
Optionꢀ
Option Type
Code Table (4-e)
Optionꢀ
Input Type
Code Table (4-e)
Option2
Option Type
Code Table (4-e)
Return Data16
Return Data17
Return Data18
Return Data19
Option2
Input Type
Code Table (4-e)
Option3
Option Type
Code Table (4-e)
Option3
Input Type
Code Table (4-e)
(Reserve)
0xFF
Return Data20
Return Data21
Return Data22
Return Data23
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data24
Return Data25
Return Data26
Return Data27
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data28
Return Data29
Return Data30
Return Data31
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data32
Check Sum
(Reserve)
0xFF
0xXX
FWD-S42Hꢀ
25
Download from Www.Somanuals.com. All Manuals Search And Download.
10. User Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x50
Code Table (5)
0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x70
0x00
0x03
0x70
0x73
Completed
Command Canceled
Code Table (5)
Function
Range/Switch code
Command
Control
Enquiry
No
Standby
Power On
0x00
0x0ꢀ
0x02
0x03
Picture Reset
Yes
Disable
Enable
Audio Reset
Size Reset
Size, Shift
Picture Reset2
(FW50)
Contrast, Brightness,
Chroma, Phase
0x04
All Reset
FWD-S42Hꢀ
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2
SNMP
1. SNMP
FWD-S42H1/S47H1 installs SNMP (Simple Network Management Protocol). SNMP is a standard
protocol for network management that was standardized in IETF (Internet Engineer Task Force).
By using SNMP, the management information of equipment connected to a network can be gotten via a
network. The information of multiple equipment gotten using SNMP can also be unitarily managed by
using SNMP management software.
The equipment corresponding to SNMP has a “management information database” called MIB (Manage-
ment Information Base) in the inside of equipment. In SNMP, the bidirectional communication of data
contained in MIB is realized between a “management system” and “management object system” that exist
in a network.
In MIB, there is the standard MIB prescribed by RFC. Especially, MIB-2 (formal name: MIB-II) is its
representative MIB. MIB-2 was established to manage a network. MIB-2 is installed in much network
equipment such as a PC, router, and switch as a standard feature. This unit installs this MIB-2.
Monitoring and monitored sides exist when equipment is monitored via a network using SNMP. The
monitoring side is called an “SNMP manager”. It is mainly constituted by the software of PC. For the
monitored side, a module called an “SNMP agent” is installed. SNMP-compatible equipment transmits
MIB information to an SNMP manager via this SNMP agent. This unit installs this SNMP agent. This
unit can realize the communication with a general-purpose SNMP manager using this SNMP agent.
Basically, an SNMP agent replies only when an inquiry is sent from an SNMP manager.
The SNMP manager periodically inquires the equipment, which it manages, about MIB information. This
way to get information is called “polling”. In polling, equipment replies using a response command when
an SNMP manger sends a request command to equipment. By polling, therefore, equipment can be
monitored without applying a high load to the equipment.
On the other hand, notification can also be done from the equipment side to an SNMP manager. This noti-
fication is called a “trap”. Using this trap, when a serious trouble occurred in equipment, it can be notified
to the SNMP manager in a short time.
This unit is compatible with the two polling and trap protocols described above. Equipment can be
efficiently monitored using these protocols.
FWD-S42H1
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Specifications of SNMP Installation
The specifications of the SNMP agent installed in this unit are shown in below.
. SNMP version:
. MIB definition:
. Support PDU:
SNMPv1
SMIv2
GetRequesat
SetRequest
GetNextRequest
Trap
. Standard MIB to be installed: MIB-II
3. Installation
The setting below is required to use the SNMP function of this unit. (Set according to your network
environment and SNMP management environment.)
. Community and its Community property
. Authentication trap
. Host restriction
The Web server function of this unit is used for setting. Refer to the Operation Manual of this unit for the
operation of the Web server.
The contents of each item and the setting of SNMP are fully described in this specification.
4. Operation of SNMP Setting Window
This section describes the procedure and contents for
setting of SNMP.
Open the Web page of this unit and click the [SNMP]
button in the Advanced setting item on the Setup page
(where an administrator’s password is necessary). The
SNMP setting window is displayed.
SNMP Setting window (on Web Page)
FWD-S42H1
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4-1. Community
A Community name is used as the password for SNMP access. The request received from an SNMP man-
ager is accepted when the Community name contained in the request coincides with the Community name
set. The request is rejected when the former does not coincide with the latter.
A maximum of three Communities can be set.
There are “Rights” and “Trap destinations” items in the property of Community. The property can be set
for each set Community.
n
When multiple Communities are set, all set Communities are validated.
1. Rights
The rights that can be set are as follows:
Read Only: An SNMP manager can reference MIB information using this Community name.
Read Write: This Community must be set when a write request is sent from an SNMP manager.
Other:
Do not set this option because it is used for the function extension in future.
2. Trap destinations
When Trap destinations are set, during trap occurrence, a trap is notified to the equipment set as trap
destinations using the Community name set.
Up to four Trap destinations can be set to one Community.
Trap destinations are not set in default.
n
This product can be set on only the Web screen because it does not install the automatic setting func-
tion of Trap destinations.
3. Setting procedure of Community
Community can be added, edited, and removed.
The addition, editing, and removal procedures of Community are described below.
Addition of Community
1. Click the [Add] button.
The “Community name”, “Rights”, and “Trap destinations” text boxes, and [Set|to|List] and
[Cancel] buttons are validated.
2. Type the Community name you want to add.
3. Set the Rights of Community and the Trap destinations you want to add.
When you want to save the setting, click the [Set|to|List] button and then click the [Apply]
button at the bottom of the window.
m
. Click the [Cancel] button when you want to discard the setting during setting.
. When you want to save setting, be sure to click the [Set|to|List] button and then click the
[Apply] button.
FWD-S42H1
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Editing of Community
1. Select the Community, you want to edit, from a drop-down list.
2. Click the [Edit] button.
The “Community name”, “Rights”, and “Trap destinations” text boxes, and [Set|To|List] and
[Cancel] buttons are validated.
Edit the Community name when you want to edit a Community name.
3. Set the Rights of Community and the Trap destinations you want to edit.
m
. Click the [Cancel] button when you want to discard the setting during setting.
. When you want to save the setting, click the [Set|to|List] button and then click the [Apply]
button at the bottom of the window.
Removal of Community
1. Select the Community, you want to remove, from a drop-down list.
2. Click the [Remove] button and then click the [Apply] button at the bottom of the window.
n
Be sure to click the [Remove] button and then click the [Apply] button.
4-2. Authentication Trap
An authentication trap is the trap for making it detect by an SNMP manager that an illegal access was
gained to this unit using an SNMP protocol.
. The authentication trap is validated when this check box is selected. A trap is transmitted when an
illegal access is gained.
. The authentication trap is invalidated when this check box is not selected. A trap is not transmitted even
if an illegal access is gained.
n
Be sure to click the [Apply] button when you edited setting.
4-3. IP Restriction of Host
It is possible to put restrictions on the IP address of an SNMP manager, as one of the security countermea-
sures, which communicates using an SNMP protocol.
. IP address restriction is invalidated when you select “Accept packets from any host”.
. Only the SNMP access from an SNMP manager that has the set IP address is accepted when you select
“Accept packets from those hosts”. The SNMP access from an IP address that has not been set is reject-
ed.
m
. Up to four IP restrictions can be set.
. Be sure to click the [Apply] button when you edited setting.
FWD-S42H1
30
Download from Www.Somanuals.com. All Manuals Search And Download.
5. MIB to Be Installed
This unit installs MIB-2.
MIB-2 is the most representative standard MIB. It is installed in various network products.
The statistical information on the amount of network traffic or the number of transmitted and received
packets is defined, and the change or transition can be monitored by polling the information periodically.
Additionally, the management items to be installed can be defined using a TCP/IP device so as to get the
information effective for the monitoring of the network communication state.
Refer to RFC1213 for the detailed definition of MIB-2.
6. Information to Be Notified on Trap
In software version 2.0 or later, the software have a function that transmits error information to this unit.
The error trap and authentication trap are installed.
FWD-S42H1
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3
ID Talk
ID Talk is set as described below. ID Talk is a protocol for operating the function of this unit via a net-
work.
1. Default Setting
Item
Description
Transport
TCP
Port number
53484 (Factory setting)
30 seconds (Factory setting)
TCP connection time-out
FWD-S42H1
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Setting Items
The items that can be set to ID Talk are shown in the table below.
Item
Description
Start ID Talk Service
Select the check box when using ID Talk. Clear the check box when using no ID Talk.
(default setting: OFF)
Port No.
Timeout
Changes the port number. A port number have to change port number 53484 cannot
be used because it has been already used for another purpose.
Specify the timeout time of connection.
Connection is automatically disconnected when communication is not done for the
specified time.
IP address of client
(Host Address)
Executes only the request from the specified IP address.
ID Talk does not have the security function such as user authentication. During
installation, safety can be improved by setting this item.
Multiple host addresses can be set.
Community
Changes the community of a header. Four (upper-or-lower case) alphanumeric
characters can be set.
(default setting: SONY)
Set the items described above properly on the SETUP → ID Talk page of the Web page when using ID
Talk.
3. Packet Structure
The packet structure of ID Talk is described below.
Community Command
Data
(n)
(4)
(4)
Header
(2)
Packet structure
3-1. Header
The header is constituted by two bytes consisting of a version (8 bits) and category (8 bits).
0
1
(Bit position)
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Version (8) Category (8)
Header structure
Version
Indicates the version number of an ID Talk protocol.
This version is fixed to 02h (version 2).
Category
Contains the category number of display equipment to be controlled. A category number is confirmed on
the display equipment side. A request is ignored when a different category number is contained.
Code
Category
10h
Information Display
FWD-S42H1
34
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2. Community
A request is executed when community coincides with the community set in display equipment. Commu-
nity consists of four (upper- or lower-case) alphanumeric characters. “SONY” is a factory-setting value.
The set character can be changed on the Web page.
(Bit position)
1
0
0
1
0
2
0
3
0
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
Community (32)
Community packet
3-3. Command
The format of a request packet and response packet is described below.
(Bit position)
0
1
2
3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
Item No(16)
Data Length(8)
Request/Response(8)
Command packet
3-4. Request
The format when sending a request from a host to display equipment is described below.
Community
This is the same alphanumeric character as the community set in display equipment that sends a request.
Request
This is a request for display equipment.
Item No.
This is the item number to be treated for request.
Data Length
This is the length of data incident to a request. The maximum length is 128 bytes. The length of data is
“0” when no data exists.
Data
This is data incident to a request.
3-5. Response
The format when display equipment returns a response to the request from a host is described below.
Community
This contains the same alphanumeric character as a request. For a short header and short community, this
is embedded with 00h.
Response
This contains the result of a request.
Item No.
This is the item number to be treated for response.
Data Length
This is the length of data incident to a response. The maximum length is 128 bytes. The length of data is
“0” when no data exists.
Data
This is data incident to a response.
FWD-S42H1
35
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Requests and Responses
Requests and responses are described below.
4-1. Requests
Requests are only a GET request that gets the display information or state and a SET request that changes
the setting of display equipment.
Request
Contents
SET (00h)
GET (01h)
Writes data in the register of display equipment.
Gets the installation information, equipment state, or setting values.
SET command:
Communication with the main microcomputer of display equipment can be done via a network by using
the protocol dedicated to FWD-S42H1/S47H1 as well as an ID Talk protocol. Use a SET command in
this case. (Also, use a SET command when receiving information from the display equipment.)
4-2. Responses
A response returns the result of execution to the request from a host.
Response
Contents
NG (00h)
OK (01h)
Indicates that a request is invalid or could not be executed.
Indicates that a request could be executed normally.
4-3. SET request
The SET request sets a new value to the specified item. A request and its response are described in details
below.
Request
Data
Length
Request
00h
Item No.
Item No.
Data
n
Set Data(n byte)
SET request
Response
OK(01h)
Item No.
n
Get Data(n byte)
Response to SET request
4-4. GET request
The GET request gets the value of the specified item. A request and its response are described in details
below.
Request
Data
Length
Request
01h
Item No.
Item No.
0
GET request
Response
OK(01h)
Item No.
n
Get Data(n byte)
Response to GET request
FWD-S42H1
36
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5. ERROR response
An NG message is returned as a response when an error occurs in the contents of a request or the result of
execution.
NG(00h)
Item No.
2
Error Code(16)
ERROR response
5. Items
Category
Contents
SET
GET
80**h
90**h
F100h
Gets the information of this unit
O
_
O
O
_
Gets the network setting information.
FWD-S42H1/S47H1 dedicated protocol
O
5-1. 80**h
This item gets the information of the connected display equipment.
Lower byte
Contents
SET
GET
00h
01h
02h
03h
Category Code
Model Name
_
_
_
O
O
O
O
O
Serial Number
Installation Place
0x8000 Category code
1 byte
0x8001 Model name
12 alphanumeric characters
For under 12 alphanumeric characters, the remaining section is set as 00h.
0x8002 Serial number
4 bytes
0x8003 Installation place
24 alphanumeric characters
For under 24 alphanumeric characters, the remaining section is set as 00h.
FWD-S42H1
37
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2. 90**h
This item gets the network setting information.
Lower byte
Contents
SET
GET
00h
01h
02h
03h
04h
MAC Address
IP Address
_
_
_
_
_
O
O
O
O
O
Subnet Mask
Default Gateway
DHCP
0x9000 MAC Address
6 bytes
0x9001 IP Address
4 bytes
0x9002 Subnet Mask
4 bytes
0x9003 Default Gateway
4 bytes
0x9004 DHCP
1 byte
DHCP invalid data value: 0
DHCP valid data value:
1
5-3. F100h
FWD-S42H1/S47H1 dedicated protocol packets can be transmitted to the main microcomputer of FWD-
S42H1/S47H1 as ID Talk data according to the FWD-S42H1/S47H1 dedicated protocol. The response of
protocol is returned as the data of ID Talk response packets.
Refer to “Section 1 RS-232C” for details on the FWD-S42H1/S47H1 dedicated protocol.
FWD-S42H1
38
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Error Codes
An error code list and its details are shown in the table below.
Category
Error
Error code
Item Error (01**h)
Invalid Item
01h
02h
03h
04h
11h
80h
01h
01h
02h
03h
11h
12h
13h
01h
01h
10h
20h
30h
40h
50h
F0h
10h
20h
Invalid Item Request
Invalid Length
Invalid Data
Short Data
Not Applicable Item
Different Community
Invalid Version
Invalid Category
Invalid Request
Short Header
Short Community
Short Command
Timeout
Community Error (02**h)
Request Error (10**h)
Network Error (20**h)
Comm Error (F0**h)
Timeout
Check Sum Error
Framing Error
Parity Error
Over Run Error
Other Comm Error
Unknown Response
Read Error
NVRAM Error (F1**h)
Write Error
6-1. Item errors
An item error occurs when the Item No. or Data of a request is invalid. The conditions under which each
error occurs are described below.
Invalid Item
When Item No. that is not supported is specified
Invalid Item Request
When Item No. is supported, but Request that is not supported is requested
Invalid Length
When the Data Length of the specified Item No. is too long
Invalid Data
When the Data of the specified Item No. differs in the setting range
Short Data
When the length of data differs from the value specified using Data Length
Not Applicable Item
When an item that is not valid at present is specified
6-2. Community error
This error occurs when community differs.
FWD-S42H1
39
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3. Request errors
These errors occur when a header or command is invalid. The conditions under which each error occurs
are described below.
Invalid Version
When the version of a header is other than 2
Invalid Category
When a category differs
Invalid Request
When a request that is not supported is specified
Short Header
When the received data is 1 byte
Short Community
When the received data is 2 to 5 bytes
Short Command
When the received data is 6 to 9 bytes
6-4. Network error
This error occurs in TCP/IP. The conditions under which an error occurs are described below.
Timeout
When communication was interrupted halfway
6-5. Comm error
This is an error that occurs during communication with the main control microcomputer of display equip-
ment.
Timeout
When the received data is not sent after data transmission
Check Sum Error
When a check sum error occurs in the main control microcomputer
Framing Error
When a framing error occurs
Parity Error
When a parity error occurs
Over Run Error
When an overrun error occurs
Other Comm Error
When other errors occur
Unknown Response
When data that cannot be processed is received
6-6. NVRAM error
Read Error
When the read operation from NVRAM fails
Write Error
When the write operation to NVRAM fails
FWD-S42H1
40
Download from Www.Somanuals.com. All Manuals Search And Download.
|