CHIPPER/SHREDDER VACUUM KIT
Mfg. Nos. 1692210, 1692231,
INSTALLATION
INSTRUCTIONS
WARNING
A
Never operate the machine without the cou
assembly or plug connected to the
Turn off the engine, let the rotor come to a
complete stop and disconnect the spark plug
wire before assembling the vacuum kit or
changing attachments.
arrows (or seams) running along the top of the cou-
pler with those on the adapter. Push fully in and turn
until it snaps into place.
WARNING
Never remove% adapter from the back of the
machine while the machine is running or the
rotor is turning. The rotor is
es away from the adapter iniet. Serious injury
will result if you put your fingers or foot in the
adapter inlet while the rotor is turning!
Insert plug (3) into adapter when
NOTE:
just inch-
attachment is not in use. See Removing the
Vacuum Kit on the
page.
4. Slip the grip (12) onto the handle (11). Putting some
soap on the handle will make the grip slide on easi-
er.
INSTALLATION
5. Connect the handle to the nozzle (6) using the
1. Remove the rotor housing cover. Retain the screws.
screw
washers (9) and nut (8).
2. Replace the cover with the adapter
or
B) using
the screws removed in step 1 and washers (15).
6. Connect nozzle (6) or leaf tray (5) to the hose,.
7. Securely place hopper lid (14) on hopper.
the coupler (2) onto the end of the hose (4).
Insert the coupler into the adapter
aligning the
Ref. Qty. Part No.
Description
Adapter
1
1
1
1
1021100
1713522
1023100
1025100
1035100
1027100
1030100
1024100
1960294
1921319
6041612
Adapter (European Model)
Coupler
Plug
Hose,
Leaf Tray
Nozzle
Ring
Nut, Hex, Flange,
Washer,
2
3
x 4” Dia.
4
1
1
1
1
5
6
7
8
1
1
9
Screw, Phillups Hd.
IO
1
Handle
1 1
1
1026100
1028100
5001612
12
Grip, Handle
Decal, Danger
Hopper Lid (Orange)
Hopper Lid (Gold)
Hopper Lid (Red)
13
14
1
1
1
1
15
3
1919326
l
Lid color depends on which kit you’ve ordered. Only
one lid is packaged per kit.
Figure 1. Kit Parts
1709566
FORM
PRINTED IN U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUMING TIPS
USING THE VACUUM
Keep the hose straight for best performance.
The vacuum kit lets you take full advantage of the
vacuum created by the four fan blades on the rotor fly-
wheel. Placing the lid on the hopper directs the suc-
tion power to the hose inlet at the bottom of the hous-
ing.
Rake leaves into the tray at a steady rate so that the
engine or motor runs at an even level. For best
results, do not cram the tray full of leaves.
Avoid items, such as twigs, that can get caught in
the hose.
Use the vacuum kit to conveniently rake dry leaves
and grass clippings into the leaf tray, where the mater-
ial is sucked through the vacuum hose, shredded in
the shredding chamber and expelled out the dis-
charge chute. The hopper lid must be in place for the
vacuum to work properly. The clear vacuum hose
allows you to monitor the flow of material. The
kit works best on dry leaves,
If material is wet, allow to dry before vacuuming.
REMOVING THE VACUUM KIT
When not using the vacuum kit, turn off the engine,
let the motor come to a complete, stop and discon-
nect the spark plug wire.
The nozzle and handle can be attached to the end of
the hose for, hard to reach places. The strength of the
vacuum can be adjusted by turning the sleeve on the
nozzle end. Open the sleeve fully for minimum suction
power to vacuum leaves over a garden area.
2. Rotate the coupler/hose assembly until the seams
line up on top, pull until it clicks then unscrew and
remove.
3. Insert the plastic plug (3) into the adapter and twist
until it seats completely
FORM 1709566
Download from Www.Somanuals.com. All Manuals Search And Download.
|