CyberPro PCI 2S
Quick Installation Guide
Introducing the CyberPro PCI 2S
The CyberPro PCI 2S high-speed serial I/ O card provides
two additional 9-pin serial ports.
FeaturesandBenefits
•
•
•
Conforms to PCI v2.2 Plug and Play
Full support for Windows-based software
Red u ces CPU load and im p roves system
performance dramatically
•
•
IRQ sharing feature reduces IRQ conflicts
High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label printers and other serial port
devices
•
•
Built-in FIFO buffers dramatically increase data
transmit/ receive speed,especially under Windows'
multitasking environment
Each serial port can be configured for either 5V or
12V output, for serial devices that require power
SystemRequirements
•
Pentium® or equivalent computer with an available
PCI slot
•
Windows® 7 (32-/ 64-bit) / Vista (32-/ 64-bit) / XP
(32-/ 64-bit) / Server 2003 & 2008 (32-/ 64-bit) / 2000
/ NT 4.0 / ME / 98SE / 98 / 95
1
04-0341D
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Installation
General instructions for installing the card are provided
below . Since the d esign of computer cases and
motherboards vary, refer to your computer’s reference
manual for further information, if needed.
Static Electricity Discharge may permanently damage
your system. Discharge any static electricity build up in
your body by touching your computer’s case for a few
seconds. Avoid any contact with internal parts and
handle cards only by their external edges.
1. Turn OFF the power to your computer and any
other connected peripheral devices.
2. Unplug the power cord from the back of the
computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. Set JP1and JP2jumper settings to the desired voltage
only if your serial device needs additional power
from the serial port. However, most serial devices
do not require additional power. For more
information see Figure 1 on page 2. Skip this step if
power is not required.
6. To install the card, carefully align the card's bus
connector w ith the selected PCI slot on the
motherboard. Push the board down firmly, but
gently, until it is well seated.
7. Replace the slot bracket holding screw to secure the
card.
8. Replacethecomputer cover and reconnect thepower
cord.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Driver Installation
This section provides information on how to install the
CyberPro PCI 2S drivers.
Windows7(32-/64-bit)
1.
Right click Computer, click Manage, click Device
Manager.
2. Insert the driver CD. Right click PCI Serial Port,
click Update Driver Software.
3.
Click Browse my computer for driver software.
4. Type D:, then click Next. (Change D: to match your
CD/ DVD-ROM drive letter)
5. At Windows has successfully updated your driver
software, click Close.
6
Right click Other PCI Bridge Device, click Update
Driver Software.
7. Repeat steps 3-5.
8. Right click CyberSerial Communication Port, click
Update Driver Software.
9.
Click Browse my computer for driver software.
10. Type D:, click Next. (Change D: to match your CD/
DVD-ROM drive letter)
11. At Windows has successfully updated your driver
software, click Close.
12. Repeat steps 8-11 to complete the installation.
WindowsVista™ (32-/64-bit)
1. At the Found New Hardware window, insert the
driver CD, click Locate and install driver software
(recommended), then click Continue.
2. Click Next, then click Close.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
Repeat step 2 to complete the driver installation.
Note: Windows Vista driver installation process
may take several minutes to complete.
Windows XP (32-/64-bit) / Server 2003 (32-/64-bit)
1. At the Found New Hardware Wizard, insert the
driver CD.
2. Select No, not this time, click Next. (Skip this step
if not prompted)
3. Select In stall th e softw are au tom atically
(Recommended), then click Next.
4. Click Finish.
5. Repeat steps 1-4 two more times.
6. Restart Windows to complete the installation.
WindowsServer2008(32-/64-bit)
1. At the Found New Hardware Wizard, click Locate
and install driver software (recommended).
2. Insert the driver CD.
3. Click Don't search online.
4. Click I don't have the disc. Show me other options.
5. Click Browse my computer for driver software
(advanced).
6. Type D:, then click Next. (Change D: to match your
CD/ DVD-ROM drive letter)
7. At The sofware for this device has been sucessfully
installed, click Close.
8. Repeat steps 3-7 to complete the installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
To Verify Windows 7 / Vista / XP / Server 2003 &
2008Installation
1. Check in Device Manager to verify installation.
For Windows 7: Right click Computer, click Manage,
then click Device Manager.
For Windows Vista: Right click Computer, click
Manage,click Continue,then click Device Manager.
For XP / Server 2003: Right click My Computer, click
Manage, then click Device Manager.
For Server 2008:Right click Computer,click Manage,
d ouble click D iagn ostics, then click D evice
Manager.
2. Click on the + (plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Dou ble click M u ltifu n ction ad ap ters, SIIG
CyberPro 2S board should be displayed.
Windows2000
1. At the Found New Hardware Wizard, click Next.
2. Select Search for a suitable driver for my device
(recommended), then click Next.
3. Check Specify a location, uncheck the other boxes,
then click Next.
4. Insert the driver CD, type in D:\ 2000, then click OK.
(Change D: to match your CD-ROM drive letter)
5. Click Next and Finish.
6. Repeat steps 1-5 two more times.
7. Restart Windows to complete the installation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ToVerifyWindows2000Installation
1. Right click My Computer, click Manage, then click
Device Manager.
2. Click on the + (plus sign) in front of Ports (COM &
LPT), CyberSerial 16Cxxx... should be displayed
two times.
3. Dou ble click M u ltifu n ction ad ap ters, SIIG
CyberPro 2S board should be displayed.
WindowsME
1. At the Add New Hardware Wizard, select Specify
the location of the driver (Advanced), then click
Next.
2. Insert the driver CD, check Specify a location,
uncheck the other box, type in D:\ ME, then click
Next. (Change D: to match your CD/ DVD-ROM
drive letter)
3.
4.
Click Next, then Finish.
Repeat steps 1 and 2.
5. Click Next, Next, then Finish.
6. Restart Windows to complete the installation.
Windows98/98SE
1. At the Add New Hardware Wizard, click Next.
2. Select Search for the best driver for your device
(Recommend), then click Next.
3. Insert the driver CD, check Specify a location,
uncheck the other boxes, type in D:\ 9x, then click
Next. (Change D: to match your CD/ DVD-ROM
drive letter)
4.
Click Next, then Finish.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Repeat steps 1-4.
6. Restart Windows to complete the installation.
Windows95
1. At the Update Device Driver Wizard, click Next.
2. Insert the driver CD, click Other Locations.
3. Type in D:\ 9x, click OK, then click Finish. (Change
D: to match your CD/ DVD-ROM drive letter)
4. From the Insert Disk window, click OK. When the
Copying Files dialog box pops up, type in D:\ 9x,
then click OK. (Change D: to match your CD/ DVD-
ROM drive letter)
5. Restart Windows to complete the installation.
To Verify Windows ME / 98SE / 98 / 95 Installation
1. Right click My Computer, click Properties, then
click Device Manager.
2. Double click Ports (COM & LPT), CyberSerial PCI
16Cxxx... should be displayed two times.
3. Double click M u lti-fu n ction ad ap ters, SIIG
CyberPro 2S... and PCI Function should be
displayed.
WindowsNT4.0
1. From the desktop click Start, then Run.
2. Insert the driver CD, type in
D:\ NT4\ Install_serial.exe, then click OK.
(Change D: to match your CD/ DVD-ROM drive
letter)
3. Click Next when the Welcome window appears.
4. Select Install, then click Next.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click Yes, then click Exit.
6. Restart Windows to complete the installation.
To Verify Windows NT 4.0 Installation
1. Click Start, Settings, Control Panel. Double click
Ports device icon.
2.
Two new COM ports will be assigned when
successfully installed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing COM Port Address
Some serial devices need a specific COM port in order to
work. If your serial device works properly, do not
change this setting.
Windows 7 / Vista / XP / Server 2003 & 2008 / 2000
1. From the Device Manager window double click
Ports (CO M & LPT), then d ouble click the
CyberSerial serial port you want to change.
2. Click Settings tab and click Advanced.
3. Click the down arrow that is next to the COM Port
number box and select a COM port that is not in use.
Click OK.
4. Click OK, then close Device Manager to save the
changes.
Windows ME / 98SE / 98 / 95
1. From the Device Manager window double click
Ports (CO M & LPT), then d ouble click the
CyberSerial PCI serial port you want to change.
2. Click Settings tab, click the down arrow that is next
to the Port Name box and select a COM address that
is not currently in use.
3. Click OK, then close Device Manager to save the
changes.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Support and Warranty
QUESTIONS? SIIG’s Online Support has answers! Simply visit our
web site at www.siig.com and click Support. Our online support
database is updated daily with new drivers and solutions. Answers
to your questions could be just a few clicks away. You can also submit
questions online and a technical support analysts will promptly
respond.
SIIG offersa lifetimemanufacturer warranty with thisproduct. Please
see our web site for more warranty details. If you encounter any
problems with this product, please follow the procedures below.
A) If it is within the store's return policy period, please return the
product to the store where you purchased from.
B) Ifyour purchase has passed the store's return policy period,please
follow these steps to have the product repaired or replaced.
Step 1: Submit your RMA request.
Go to www.siig.com, click Support, then RMA to submit a
request to SIIG RMA. If the product is determined to be
defective, an RMA number will be issued.
Step 2: After obtaining an RMA number, ship the product.
• Properly pack the product for shipping. All software, cable(s)
and any other accessories that came with the original package
must be included.
• Clearly write your RMA number on the top of the returned
package. SIIG will refuse to accept any shipping package, and
will not be responsible for a product returned without an
RMA number posted on the outside of the shipping carton.
• You are responsible for the cost of shipping. Ship the product
to the following address:
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
RMA #:
• SIIG will ship the repaired or replaced product via Ground
in the U.S. and International Economy outside of the U.S. at
no cost to the customer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
About SIIG, Inc.
Founded in 1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer
of I/ O connectivity products, including PCIe, PCI & ISA serial and
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire
(1394a/ b),networking,sound cards,and other accessories. SIIG is the
premier one-stop source ofupgrades.
SIIG productsoffer comprehensiveuser manuals,many user-friendly
features, and are backed by an extensive manufacturer warranty.
High-quality control standards are evident by the overall ease of
installation and compatibility of our products, as well as one of the
lowest defective return rates in the industry. SIIG products can be
found in computer retail stores, mail order catalogs, through major
distributors, system integrators, and VARs in the Americas and the
UK,and through e-commerce sites.
PRODUCT NAME
CyberPro PCI 2S
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE
FCCCOMPLIANCESTATEMENT:
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE
SIIG, Inc.
6078 Stewart Avenue
Fremont, CA 94538-3152, USA
Phone: 510-657-8688
CyberPro PCI2Sis a trademark ofSIIG,Inc. SIIG and the SIIG logo are registered trademarks ofSIIG,
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of
MicrosoftCorporation in theUnited Statesand/ or other countries. Pentium isa registered trademark
of Intel Corporation. Other names used in this publication are for identification only and may be
trademarksoftheir respectivecompanies.
October, 2009
Copyright © 2009 by SIIG, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Sharp Flat Panel Television LC 40E77UN User Manual
Shoprider Mobility Aid UL7WR 10 User Manual
Soleus Air Air Conditioner KFHHP 09 OD User Manual
Sony Headphones NWZ E443 User Manual
Sony Portable CD Player D 368 User Manual
Sony Security Camera SNCCH160 User Manual
Sony TV VCR Combo 413 User Manual
State Industries Electric Heater GP6 50 YTVIT User Manual
Superior Blower FAB 1100 User Manual
Swann Camcorder SW241 SD4 User Manual