SEBO ET-H Power Head
For Household Use Only
© Copyright SEBO America, LLC • All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
!
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE
SAVE THESE INSTRUCTIONS.
WARNING: To reduce the risk of fire, electric shock, or injury:
1. Do not leave vacuum while plugged in. Unplug from 20. Machines can cause a fire when operated near flammable
outlet when not in use and before servicing.
vapors or materials. Do not operate this vacuum near
flammable fluids, dust or vapors.
2. Do not use outdoors or on wet surfaces.
21. Maintenance and repairs must be done by qualified
personnel.
3. Do not use near small children or pets. Do not allow
to be used as a toy. Use of this product by children
should always be supervised by an adult.
22. Use only original SEBO replacement parts.
23. Do not use vacuum as a step.
4. Use only as described in this manual. Use only
manufacturer-recommended attachments.
24. Do not leave machine standing in one place with machine
turned on.
5. Do not use with a damaged cord or plug. If vacuum
is not working as it should, has been dropped, 25. While the vacuum is in use, the power cord should be
damaged, left out-doors, or dropped into water, take it to
a SEBO service center.
unwound from the cable reel at least two thirds of its length.
Hold plug when rewinding onto the cord reel. Do not allow
plug to whip while rewinding.
6. Do not pull or carry by cord, use cord as a handle,
close a door on cord, or pull cord around sharp 26. Keep hair, loose clothing, fingers, and all parts of body away
edges or corners. Do not run vacuum over cord.
Keep cord away from heated surfaces.
from vacuum openings and moving parts. Do not place
fingers or other body parts under vacuum unless it is
unplugged.
7. Do not unplug by pulling on cord. To unplug, grasp
the plug – not the cord.
27. Do not place the power head over rug edges or fringe.
8. Do not plug in if switch is in the “I” (ON) position.
28. The vacuum has a manual reset thermal protector. The
protector is reset by switching off the vacuum. The thermal
protector needs some time to cool down after switching off!
Check the vacuum for air blockages or mechanical failures
before switching on.
9. Do not use outlets above counters to plug in vacuum –
damage to items in the surrounding area could occur.
10. Always carry the vacuum over steps and sills.
11. Do not handle plug or vacuum handle with wet hands.
29. Store the vacuum in a dry place at room temperature. When
the vacuum is not in use, the cord should be wound on the
cord reel.
12. Do not put any object into vacuum openings. Do not use
machine with any openings blocked. Keep openings free of
lint, hair, and anything that may reduce air flow.
30. Any other servicing should be performed by an authorized
service representative.
13. Do not re-use filter (dust) bags or wash the filters.
14. Do not remove any screws from vacuum.
31. The hose contains electrical wires. Do not use if damaged,
cut, or punctured. Avoid picking up sharp objects.
15. Do not vacuum up anything that is burning or smoking,
such as cigarettes, matches, or hot ashes.
32. Always unplug vacuum before connecting or disconnecting
either hose or power head.
16. Do not use vacuum without dust bag and/or filters in
place.
33. Use this power head only in combination with a SEBO
vacuum cleaner.
17. Turn off all machine controls before unplugging.
18. Use extra care when cleaning on stairs.
34. Do not connect power head to a malfunctioning or damaged
vacuum.
19. Do not use machine to vacuum up flammable or
combustible liquids such as gasoline or use in areas
where they may be present.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL SEBO PRODUCT FEATURES
Your SEBO ET-H Power Head is designed specifically for use with the SEBO C3.1 and K3 canister vacuum
cleaners. These vacuums are among the most technically advanced canister vacuum cleaners in the world.
For example, the ET-H Power Head has warning systems and automatic shut-off capabilities that are
designed to alert the user to machine problems that, if ignored, will damage the machine or diminish per-
formance.
Your SEBO ET-H Power Head’s most unique features are:
1. Deep Cleaning. SEBO power heads offer deep cleaning of your carpets only a thorough brushing can
give.
2. Variable Height Adjustment. The unique pivoting brush roller housing allows the ET-H Power Head
to adjust its brush height to different types of carpeting.
3. Brush Pressure Adjustment. The ET-H power head allows the user to determine the appropriate brush
aggressiveness by adjusting the brush pressure adjustment dial on top of the power head to either soft
or hard. Adjusting the brush pressure to HARD increases aggressiveness by making the brush bristles
spin deeper in the carpet pile. Aggressiveness is decreased by adjusting the pressure dial to SOFT.
4. Brush Roller Obstruction – Auto Shut-Off. If the brush roller is obstructed, the machine will shut off
in three seconds, the amber light located on top of the power head will illuminate, and the brush rollers
will stop rotating. The user should turn the power switch off, unplug the machine, and immediately
remove the obstruction. If the user restarts the machine without removing the obstruction, the machine
will again shut off and the amber light will turn on.
5. Stationary Use. When the machine has its handle in the upright-locked position, it is designed to shut
off the brush roller. The green “power” light situated on top of the power head will remain illuminated
even though the brush roller has stopped rotating. An operating power head should not stand stationary
on the floor for inappropriate periods of time.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Parts
4
7
2
6a
1. Power head
2. Brush pressure adjustment
3. Swivel neck
3
4. Connection plug
5. Indicator lights
5
6. Brush roller end cap
6a. Edge-cleaning brush roller end cap
7. Telescopic Tube release button
1
6
Attaching the Power Head to
the Telescopic Tube of your
SEBO C3.1 or K3 Vacuum
1. Find the connection tab (A) at the base of the telescopic tube (B).
2. Move the connection tab (A) OUT away from the tube (C). See
enlarged detail below. It will only move approximately 1/8-inch.
NOTE: the tab must not be forced beyond the “flush” position
of the collar. Proceed to step 3.
3. Insert the base of the telescopic tube (E) into the power head
swivel neck (3). Make sure that the connection tab (A) is prop-
erly aligned with the connection plug (4) in the swivel neck.
Damage to the connection may occur if the tab and the plug
are not properly aligned.
B
E
A
E
A
C
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Starting The Machine - Figures 1 & 2
A. Before turning on your canister, make sure that the vacuum han-
dle is in its upright locked position (figure 1).
1. With the canister main power switch in the OFF position,
and the power control slider on the handle (#8, figure 2) in
the OFF position, pull the power cord out from the base of
the canister (see canister owner’s manual). The power
cord should be unwound from the cable reel at least two
thirds of its length.
2. Plug the polarized power cord into a 120 volt outlet
located near the floor.
3. Press the main power switch on the base of the canister
gently with your foot or hand to the ON position.
8
4. Slide the Power Control Slider (#8, figure 2) to the ON
position (the slider will “click” when it is pushed out of the
OFF position). It will then slide freely between 0 suction
and MAX suction. Set the slider to the suction desired. The
green power light situated on the top side of the power
head will illuminate.
Figure 1
Switch Position -
#8, Figure 2
0 = Zero Suction
MAX = Maximum Suction
Figure 2
Operating The Machine - Figure 3
B. When the power head is switched on with the handle in the upright locked
position (see figure 1 above), the brush roller will not spin. To release the
power head from the upright locked position, gently place your foot on the
power head for leverage and lower the handle into the operating position (fig-
ure 3).The brush roller will then start spinning.The amber indicator light may
flicker for a few seconds when you lower the handle - this is normal.
ON position - Slide the slider
down toward 0 suction till it
“clicks” out of position.
OFF position - Pull the slider
up to 0 suction then continue
pulling the slider up until it
“clicks” into the OFF position.
The handle can be lowered to a horizontal position useful for vacuuming
under beds.
You may adjust the suction control with the power control slider as you vac-
uum different surfaces or when using the accessory tools. For optimal clean-
ing and brushing, operate the machine at the maximum suction power set-
ting and push the power head slowly over the carpet.
When the canister’s main power switch is in the ON position, you may turn
the power head off and on with the power control slider (#8, figure 2). To turn
the power head off using the power control slider, pull the slider to 0 suction,
then continue pulling the slider up until it “clicks” into the OFF position. The
green power head light will then shut off.
Always turn the power off on both the canister and the power head
when changing heads or unplugging the vacuum. Slide the power con-
trol slider on the power head to its OFF position, press the main power switch
on the base of the canister gently with your foot or hand, then unplug the
canister to completely shut down the power when changing heads or storing
the vacuum. Hold the plug while rewinding the cord onto the cord reel. Avoid
letting the plug whip while rewinding.
Figure 3
!
WARNING! The quality, condition, coating, texture, age and manufacturing technique of all floor surfaces vary.
Therefore, vacuums with rotating brushes, including your SEBO, may damage some floor coverings or surfaces. Some
types of high-gloss hardwood floors, cushion vinyl, berber carpets, long shag, and delicate or hand-woven carpets are par-
ticularly vulnerable to damage by rotating brushes. When possible, consult the materials supplied by your flooring manufac-
turer for information on proper upkeep and cleaning. To ensure that your new SEBO vacuum cleaner is compatible
with your floor, please test the vacuum cleaner on each type of flooring surface in a small inconspicuous area
to determine if any damage occurs. If damage occurs, stop using the vacuum cleaner immediately!
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Brush Pressure Adjustment Feature -
2
8
Figure 4
The brushing pressure that your ET-H power head applies to
your carpet is adjustable from SOFT through HARD. When the
brush is set on SOFT, the brush pressure is decreased for a
lighter brushing action. For thorough, deep brushing, set the
pressure adjustment to HARD.
The brush pressure adjustment dial is located on the top side
of the power head (# 2, figure 4). To adjust the dial to SOFT,
spin the dial in the direction of the arrow (#8, figure 4).To adjust
the brush action to HARD, turn the dial in the opposite direction
of the arrow (#8, figure 4).
Figure 4
Indicator Lights - Figure 5
The green and amber indicator lights are located on the top of
the power head (# 5, figure 5).
Green Light:
Motor is on, power head is ready
for operation. The green light
remains illuminated when the
handle is in the upright locked
position and when it is lowered to
its operating position. However,
the green light will shut off when
the power control slider located on
the handle is in the OFF position.
5
Amber Light Flashing:
Motor is on, brush is adjusting
to carpet pile.
Figure 5
Green and Amber Lights: Motor shuts down, brush stops
spinning - indicates a shut down
due to overload, clog or jammed
brush roller.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Maintenance
9
10
9a
Always unplug vacuum from outlet
before dismantling any part of machine!
!
Changing the Brush Rollers - Figures 6 & 7
To change the brush roller (#9, figure 6) or the edge-cleaning
brush roller (#9a, figure 6), release the end caps (6 and 6a, fig-
ure 6) by pushing the button (#10 for the brush roller, #10a for
the edge-cleaning brush). Rotate the end caps in the direction
of the arrows and pull them off.Turn the 8” brush roller clockwise
and the edge-cleaning roller counter-clockwise (figure 7) when
removing them from the power head.You may also reference the
arrows on the ends of the brushes which indicate the direction
to turn the brushes to remove and replace them.
6a
10a
Figure 6
9
To insert the new brush or brushes, fit them onto the drive shafts
by turning them clockwise until they lock into position. Replace
the end caps by turning them until they click into position. Make
sure not to squeeze the bristles of the brushes under the end
caps.
9a
Cleaning the Brush Rollers
Unplug the vacuum before attempting to clean the brushes.
The brushes should be cleaned regularly.
Figure 7
Fibers and hair can be pulled out of the brushes while manual-
ly rotating the rollers, or the rollers can be removed from the
power head to clean them.
8” Replacement Brush
Part # 2754
Replacement Edge-Cleaning Brush
Part # 2756
Complete Replacement Brush Set
Part # 2758 ER
Clog Removal
Always unplug vacuum from outlet
before removing any clogs!
!
Clogs in the Airflow Pathway - Figure 8
Many clogs can be removed by accessing the airflow pathway
via the orange colored access door (#11, figure 8) located on
the underside of the power head.
Clogs in the Swivel Neck
11
Check the swivel neck regularly for blockages. Do not open the
machine. To check for a clog in the swivel neck (#3, page 5),
remove the telescopic tube by pressing the release button (#7,
page 5). Pull the tube out of the swivel neck. Push the obstruc-
tion down the neck with a stick or long screwdriver and remove
it through the orange access door (#11, figure 8).
Figure 8
For clogs not in the power head, please refer to your canister
vacuum’s manual.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble-Shooting Guide
Always unplug vacuum from outlet before dismantling any part of the machine!
!
PROBLEM
REASON
SOLUTION
Does not turn on
1. Telescopic tube not inserted properly. 1. See page 5.
2. Not plugged into good outlet.
3. Cable worn.
2. Use another outlet.
3. Replace cable.
4. The power control slider switch is
set to “0” (“off” position).
4. Slide the power control slider
switch to “on” position.
Green and amber lights
are on & machine
shuts off - brush stops
spinning
1. Jammed brush roller.
1. Remove brush roller obstruction.
See page 8.
2. Clog in airflow pathway or swivel
neck.
2. Remove clog. See page 8.
3. Overload shut down from exces-
sively deep but loose carpet pile
(e.g., long shag carpet).
3. If carpet pile is too deep and loose,
then use a “shag rake” attachment
instead of the ET-H power head.
Amber light flashing
Does not pick up
1. Brush is adjusting to carpet pile.
1. Ignore
1. Telescopic tube tube not
inserted properly.
1. See page 5.
Check your C3.1 or K3 canister user’s manual for more trouble-shooting problems and solutions.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBO ET-H Power Head
Schematic and Parts List
Pos. Part #
Description
Pos. Part #
Description
1
2
3
4
5
6
7
8
9
2701 DG
2708
2729 UL
2707
2704 DG
2730
2733
2735
2737
Chassis
Sealing strip
Internal cable
Wire tie
18 2751 DG
20 2752 DG
21 2770 UL
22 1737 DG
1739
23 2775 DG
24 2771 HG
25 2772 HG
26 2779 DG
27 2706
28 2710 GW
29 2716 DG
30 2714 DG
31 2764 UL
33 2762
34 2709 DG
35 2608 DG
36 2720
Bearing block right hand
Brush cover, cpl.
Swivel neck assembly
Release button
Leaf spring
Rear bottom plate, cpl.
Brush motor 120 V 150 W
Motor pulley
Motor support
Motor gasket
Drive belt, motor
Brush drive unit
Drive belt, brush
Motor cover
Transmission shaft, cpl.
Screw F 3.9 x 13
Printed circuit board
Brush roller set
8” Roller
Cap
Swivel neck support r.h.
Swivel neck support l.h.
Stop spring
Swivel axle
Power head cover
Bumper
Front bottom plate, cpl.
Spring bracket / switch cpl.
Adjustment spring
Wheel housing
Wheel
10 2749
11 2753
12 2750
13 2702 DG
14 2736
15 0102
16 2791 AM
17 2758 ER
17A 2754
17B 2756
Wheel axle
Access Door
Edge brush
37 2721 OR
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBO duo-P Cleaning System
Deep clean your carpet with the SEBO duo Brush Machine
and SEBO duo-P Powder
The SEBO duo Carpet Cleaning System is formulated to deep clean your
entire carpet or spot clean stubborn stains without soaking your carpet. Dry
cleaning is safer for most carpets – it will not shrink the carpet or cause water
staining if applied unevenly. SEBO duo-P Cleaning Powder leaves no deter-
gent residue to cause your carpet to resoil, and the carpet can be used
immediately after cleaning.
Because this is a DRY cleaning process, the SEBO duo-P Cleaning Powder
will not promote the growth of mold and fungus in your carpet and pad that
wet extraction systems may cause. In addition, the GAF allergy research
center in Germany found in a long term test that, six months after a single
cleaning with duo-P, seven out of ten carpets remained free of dust mite
allergens.
The Advantages of using the SEBO duo Cleaning System are:
• No detergent residue
• Alleviates house dust allergies • No need to move furniture
• Easy spot cleaning • Cleans most types of carpets
• No shrinkage or mildew
• A built-in fiber protector helps • Immediate use of the carpet
to protect your carpet against future stains and soil
How it Works:
The SEBO duo-P Cleaning Powder is made up of granules that are mois-
tened with detergent and is environmentally friendly and safe to use. When
the granules are worked into the carpet fiber, soil and stains are lifted out of
the carpet by the duo-P powder. The duo Brush Machine lifts the carpet pile
ensuring all surfaces of the fiber are cleaned, leaving your carpet revived and
softer. After vacuuming, the duo-P powder is removed, and your carpet is left
clean, dry and ready for use.
The duo-P Cleaning Powder:
Refill boxes are available as a single
(1.1 lb.) or a multiple with five (1.1 lb
each) packs. Each single pack can
cover up to 250 square feet of carpet.
Deep clean your carpet in three easy steps:
The SEBO duo-P
Clean Box contains
a 1.1 lb. pack in an
environmentally
friendly refillable
container, and the
underside of the lid
has a built-in brush
for spot cleaning!
1. Spread duo-P Cleaning Powder evenly over the carpet.
2. Work the powder into the carpet using the SEBO duo Brush Machine,
which opens the carpet pile enabling the duo-P powder to clean around each
separate fiber.
Spot clean small
areas or stubborn
stains.
3. Once the duo-P powder has absorbed all of the dirt and the area is dry to
the touch (approximately 30 minutes), simply vacuum the area thoroughly.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SEBO Vacuum Cleaner Warranty
Three Years Non-Wear Parts - One Year Labor
1. Your authorized SEBO dealer or SEBO will provide
7. The Wear Parts excluded from warranty coverage
the original product purchaser with replacement of
Non-Wear Parts which fail due to a material or work-
manship defect for a period of three (3) years from
the original date of purchase of new product.
include the brush rollers, the front bottom plate and
the rear bottom plate.
8. This warranty applies only while your SEBO power
head is physically located within the United States of
America and its territories or Canada.
2. Your authorized SEBO dealer or SEBO will repair (or
SEBO will cover labor charges associated with
repair) a defective SEBO power head at no cost to
the original purchaser, within one (1) year of original
purchase of new product.
9. The purchase receipt showing the date, price, and
item of purchase is the initial document of proof of
purchase and determines the validity of warranty. To
be certain that your warranty claim can be
processed as quickly and efficiently as possible,
please retain your original purchase receipt and mail
in the warranty card provided with your new SEBO
power head or vacuum cleaner.
3. SEBO America, Floor Care Equipment, Ltd., or an
authorized SEBO dealer must complete all warranty
repairs.
4. To locate an authorized SEBO dealer in your area,
or to register a warranty claim in the United States
of America, please call SEBO America at
(800) 334-6614.
10. This warranty gives you specific legal rights.You may
also have other legal rights, which vary from
state/province to state/province.
5. To locate an authorized SEBO dealer or to register a
warranty claim in Canada, please call Floor Care
Equipment, Ltd. at (800) 661-8687.
11. SEBO America will not process nor will it accept
responsibility for warranty claims for machines
purchased from dealers located in Canada.
Floor Care Equipment, Ltd. will not process nor will it
accept responsibility for warranty claims for
machines purchased from dealers located in the
United States.
6. The warranties provided for above apply exclusively
to SEBO power heads which are used residen-
tially. No warranty is provided for SEBO power
heads used commercially.
EXCLUSIVE REMEDY:
The remedies provided under the terms of this Warranty are the purchaser’s exclusive remedies and are in lieu of any
other remedies otherwise available.
LIMITATIONS AND EXCLUSIONS:
THE WARRANTY DOES NOT COVER:
• Used or secondhand products.
• Products outside of the warranty period.
• Items not manufactured by SEBO.
• Normal maintenance service.
• Equipment damaged by improper use,
accident, other casualty or negligence.
• Machines equipped with nonauthorized
attachments or modifications.
• Machines on which the serial number has
been altered or removed.
SEBO MAKES NO OTHER REPRESENTATIONS OR WAR-
RANTIES, EXPRESSED OR IMPLIED AND SPECIFICALLY
EXCLUDES THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR
PURPOSE.
A
PARTICULAR
SEBO WILL NOT BE LIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES OF ANY KIND OR NATURE.
THIS DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT
APPLY TO THE EXTENT SAID DISCLAIMER IS NOT
ALLOWED BY APPLICABLE STATE/PROVINCIAL LAW.
To contact SEBO in the United States of America:
SEBO America, LLC
Telephone: (800) 334-6614 • (303) 792-9181
Fax: (303) 792-9196
To contact SEBO in Canada:
Floor Care Equipment, Ltd.
Telephone: (800) 661-8687 • (403) 250-5005
Fax: (403) 250-5057
E-mail: [email protected]
E-mail: [email protected]
02/2003
06586
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
|