CD DIGITAL TUNER
with REMOTE CONTROL
OWNER'S MANUAL
SMV122
SMV122_ib_060402.p65
31
4/6/2002, 17:43
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you… … … … … …
for purchasing this H.H. SCOTT audio product. The H.H. SCOTT brand is
your assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this
product. Please be sure to read this Owner’s Manual completely to make
sure you are getting the maximum benefit from each feature.
This product was manufactured using the highest quality components and
standards of workmanship. It was tested by H.H. SCOTT inspectors and
found to be in perfect working order before it left our factory. However,
there is always the chance that some problem may occur because of rough
handling during shipment to the retail store or to the final consumer.
If, after reading this Manual, you experience any problems with the operation
of this product, please refer to the instructions for obtaining service at the
end of this Manual. H.H. SCOTT and H.H. SCOTT retailers are committed
to your satisfaction.
Once again, thanks for purchasing this H.H. SCOTT audio product.
For future reference, record the serial number in the space provided.
Model No: SMV122
Serial Number :
2
SMV122_ib_060402.p65
2
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
INVISIBLE LASER RADIATION
WHEN OPEN AND INTERLOCKS
DEFEATED.
APPAREIL Á LASER DE CLASSE 1
PRODUCTO LASER DE CLASE 1
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
• Avoid installing this unit in places • Operate controls and switches as
exposed to direct sunlight or close to
described in the manual.
heat radiating appliances such as • Before turning on the power, make
electric heaters, on top of other stereo
equipment that radiates too much
certain that the power cord is properly
installed.
heat, places lacking ventilation or dusty • When moving the set, be sure to first
areas, places subject to constant
vibration and/or humid or moist areas.
disconnect the power cord and remove
cords connected to other equipment.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a class B
digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
3
SMV122_ib_060402.p65
3
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION FOR USE
Unpacking And Set Up
• Remove the unit from the carton, and remove all packing materials from the
unit.
• Save the carton and packing materials in case the unit ever needs to be returned
for service. Using the original carton and packing materials is the only way to
safely repack the unit for shipment.
• Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
• Remove any small strips of tape that may have been used to prevent the CD
door from opening in transit.
• Open the CD door and remove the CD pickup protect card from the CD
compartment. Discard it and close the CD door.
• Unwind the FM wire antenna and extend it to its full length.
• Place the unit on a stable, level surface such as a table, desk, shelf, etc within
easy reach of an AC outlet, out of direct sunlight, and away from sources of
excessive heat, dust, moisture or humidity.
Power Supply
This unit is designed to operate only on normal 120V 60Hz AC house current.
Operating this unit from any other power source may cause damage to the unit
and such damage is not covered by your warranty.
This unit has a polarized AC plug with one wide blade and one narrow blade.This
plug will only fit into a matching polarized AC outlet. This is a safety feature to
reduce the possibility of electric shock. If this plug will not fit in your AC outlet, you
probably have an outdated non-
polarized outlet. You should have
your outdated outlet changed by a
qualified, licensed electrician. Do not
AC Outlet
file the wide blade on the plug, or use
an adapter to make the plug fit into
your outlet. This defeats the safety
feature and could expose you to
electric shock.
AC Plug
4
SMV122_ib_060402.p65
4
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
SET UP PROCEDURES
STEP 1
STEP 2
STEP 3
STEP 4
5
SMV122_ib_060402.p65
5
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF CONTROLS AND INDICATORS
FRONT VIEW
12
11
11
13
10
9
7
5
3
1
14
16
8
6
4
2
15
17
18
19
21
20
BACK VIEW
1
23
22
24
3
25
26
6
SMV122_ib_060402.p65
6
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
1.) POWER/STANDBY
2.) TUN/ SKIP UP
3.) TUN/ SKIP DN
4.) CD PLAY / PAUSE
5.) RANDOM Button.
6.) CD Button.
Button.
Button.
Button.
Button.
7.) TUNER Button.
8.) BAND Button.
9.) STANDBY LED Indicator.
10.) MUTE LED Indicator.
11.) Speakers.
12.) CD Door.
13.) Multi-Function LCD Display.
14.) REMOTE SENSOR.
15.) VOL DN Bntton.
16.) VOL UP Button.
17.) PRESET EQ Button.
18.) MEMORY-UP / REPEAT Button.
19.) CD STOP
Button.
20.) MEMORY / C-ADJ Button.
21.) CD Door OPEN / CLOSE Button.
22.) AC Socket.
24.) LINE OUT RCA Jacks.
23.) SUBWOOFER RCA Jack.
25.) PHONES Jack.
26.) FM Wire Antenna.
7
SMV122_ib_060402.p65
7
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
10
1.) TIMER Button.
2.) SLEEP Button.
3.) TUNER Button.
4.) BAND Button.
11
12
13
9
5.) TUNING Up /
CD Skip Search Forward
6.) TUNINGDown /
CD Skip Search Reverse
7.) INTRO Button.
Button.
Button.
14
17
8
15
16
7
6
4
5
3
18
19
8.) MEMORY / C-ADJ Button.
9.) MUTE Button.
2
1
20
10.) Infra Red Signal Transmit LED.
11.) POWER On/Off Button.
12.) Number Key Pads.
13.) REMAIN / MODE Button.
14.) RANDOM Button.
15.) REPEAT / MEM-UP Button.
16.) CD PLAY / PAUSE
17.) CD STOP Button.
18.) CD Button.
Button.
19.) VOLUME DOWN / UP Buttons.
20.) PRESET EQ Button.
8
SMV122_ib_060402.p65
8
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY INSTALLATION
Insert 2 ‘AAA’ size alkaline batteries, not included, into the battery compartment
of the remote handset, observing the battery polarity and replace the cover.
BATTERY REPLACEMENT
When the batteries become too weak, the operating distance of the remote handset
is greatly reduced and you will need to replace the batteries.
NOTES:
• To maintain the accuracy and long life of the transmitter, do not press two or
more buttons simultaneously.
• If the remote control is not to be used for a long time, remove the batteries to
prevent possible damage through leaking batteries.
• Do not mix different types of batteries, or old batteries with new ones.
USING THE REMOTE CONTROLLER CORRECTLY
• Point the remote handset at the Remote Sensor on the front panel.
• The functions of the buttons on the remote handset are the same as the
corresponding controls on the main unit.
• When there is a strong ambient light source, the performance of the infrared
Remote Sensor may be degraded, causing unreliable operation.
• The maximum effective distance for remote control operation is about 16 feet
(Approx. 5m)
9
SMV122_ib_060402.p65
9
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
CONNECTION TO ACTIVE SUBWOOFER
To enhance high bass, connect the RCA SUB WOOFER jack located at back of
unit to your active subwoofer.
CONNECTION TO EXTERNAL AMPLIFIER
You have a possibility to connect to external Amplifier through RCA LINE OUT
jacks located at back of unit.
SETTING THE CLOCK
Clock can be set while clock time is displayed, at STANDBY mode or CD, TUNER
modes. During CD, or TUNER operations, press REMAIN/MODE button until clock
is displayed, and follow the procedures below:
1.) Press the MEMORY / C-ADJ button for more than one second. The unit will
then display the time and HOUR will start flashing.
MEMORY
AM
2.) Adjust the hour by pressing the
or PM.
/
buttons. Set the correct hour for AM
3.) Press MEMORY / C-ADJ button to confirm. Minutes will start flashing.
4.) Adjust the minutes by pressing the
/
buttons.
AM
5.) Press MEMORY / C-ADJ button to store the time.
NOTE:
• If button is not pressed within 10 seconds, the clock display stops flashing.
• If the unit is disconnected from the AC power for more than one minute, you
will need to reset the clock.
10
SMV122_ib_060402.p65
10
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
LISTENING TO RADIO
1.) Press the POWER/STANDBY button to turn the unit ‘On’.
2.) Select the Tuner function by pressing TUNER button.
3.) Select AM or FM band by pressing BAND button. Tune to
TUN/
SK UP
TUN/
SK DN
the desired station by pressing
or
button.
4.) Adjust the VOLUME to the desired level using the VOLUME UP or DOWN
button.
5.) After finished listening, press the POWER/STANDBY button to turn power
‘Off’.
Manual Tuning
Press the
or
buttons as many times as required until the frequency of the
desired station appears on the display.
Automatic Tuning
Hold the
or
buttons for approximately 2 seconds. The Tuner will begin
scanning up or down automatically and will lock onto the next strong signal.
Note: Tune manually for weak stations.
PRESET STATIONS INTO MEMORY
You can store up to 40 of your favorite FM and AM stations randomly. Once a
station is preset in the memory, you will have quick and easy access to that station.
1.) Press the TUNER button to select the Tuner mode.
2.) Select the band (AM/FM) by pressing the BAND button.
3.) Select the desired station by pressing the
or
buttons.
11
SMV122_ib_060402.p65
11
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
4.) Press the MEMORY button. The memory indicator will flash in the display.
MEMORY
MEMORY
CH
FM
MHz
5.) Press the MEMORY-UP button to select any one of the 20 available preset
station memories.
MEMORY-UP/
REPEAT
CH
FM
MHz
6.) Press the MEMORY button again to enter the selected radio station into the
selected memory location.
7.) Repeat the above steps 2 – 6 to enter all your desired stations into the preset
station memories.
TUNING TO PRESET STATIONS
After you have entered up to 40 (20 AM, 20 FM) stations in the preset memories,
you can select any one of the memorized stations quickly and easily by simply
pressing the MEMORY-UP button until the desired memory number and station
frequency appear in the display.
ANTENNA INFORMATION
• For best FM reception, the FM lead wire antenna, located on the back of the
set, should fully unwound and extended.
• The AM bar antenna is inside the cabinet. To improve AM reception, you may
have to move or slightly rotate the main unit until you obtain the best reception.
12
SMV122_ib_060402.p65
12
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYING COMPACT DISCS
LOADING AND UNLOADING COMPACT DISCS
POWER
1.) Press the POWER
button to turn the unit ‘On’.
CD
2.) Select the CD function by pressing the CD button.
3.) Press the the CD Door OPEN/CLOSE button to open the CD compartment.
NOTE: The CD door is motorized and will open slowly. Do not touch the CD
Door.
OPEN/CLOSE
4.) When the disc compartment has opened, insert the disc with the label side
facing out. Push down in the center until disc is locked in place.
5.) Close the disc compartment by pressing the CD Door
1234
5678
9 10>
OPEN/CLOSE button. When the compartment is
fully closed, the disc will start turning automatically.
The total number of tracks and playing time will
appear in the display.
NOTE: DO NOT PUSH CD DOOR WITH HAND OR BY ANY MEANS TO
CLOSE THE DOOR.
6.) The disc compartment may be opened at any time by first pressing the STOP
button and then pressing the CD Door OPEN/CLOSE button. Remove the
CD only after the compartment has fully opened and the disc has stopped
spinning.
13
SMV122_ib_060402.p65
13
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
• Do not put anything except a compact disc into the compartment.
• Foreign objects can damage the mechanism.
• Keep the disc compartment closed when not in use to prevent dirt and dust from
entering the mechanism.
• Never place more than one disc into the disc compartment at any time.
• If the disc is correctly loaded, the total number of tracks on the disc will be
displayed.
NOTES:
After the disc compartment is fully closed, the disc information may not appear on
the display. This means that the disc is improperly loaded (most likely it is upside
down). To check, open the disc compartment again and reload the disc.
DISC PLAY
1.) Insert a CD as described in the previous section and close the disc compartment.
2.) The display will then show the total number of tracks and total play time.
1234
5678
9 10>
3.) Press the PLAY/PAUSE
button. Disc play will
begin from the start of the first track of the disc.
4.) As each track on the CD disc is played, the corresponding track number will
flash in the Calendar display. The “>” indicator will appear if the disc in the player
contains more than 10 tracks.
5.) A particular track can be selected using either of the CD Skip
/
buttons.
If this is done before pressing the PLAY/PAUSE
with the selected track when the PLAY/PAUSE
button, disc play will start
button is pressed.
6.) At the end of the disc, the unit will switch to stop mode.
14
SMV122_ib_060402.p65
14
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
• If the disc is deeply scratched, or too dirty, disc play may not start.
• If the disc is inserted incorrectly, or the disc is damaged the “no disc” indicator
will flash on display.
POP
DISC ERRORS
• This compact disc player has built-in error compensation circuits to correct for
minor defects in a disc. There are limits, however, to the amount of correction
available.
• In some cases, the CD player mayskip some tracks, or parts of tracks, on a disc
during disc play. This problem may be caused by defects (such as scratches)
in the disc being played, which are too large for the error compensation circuits
to handle. If you encounter this problem, check the CD player's operation as
follows, before having the unit serviced:
Play a new disc. If the CD player operates normally, the skipping problem is
probably due to a defective disc.
TO STOP A CD BEFORE THE DISC ENDS
1.) Press the STOP button. Disc play will stop, and the display will show the total
number of tracks.
2.) To temporarily stop disc play (Pause mode), press the PLAY/PAUSE
button. Disc play will stop at the current play position. The display and the track
playing time will flash.
3.) To resume disc play, press the PLAY/PAUSE
button again.
15
SMV122_ib_060402.p65
15
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACK SKIP
Starting disc play from the beginning of a particular track
Press the
or
Skip Track buttons to select the desired track. The number of
the selected track will be shown on the CD display.
PLAY/
PAUSE
Press the PLAY/PAUSE
button to start play.
To skip to the next track
For example, to skip ahead to the beginning of track 5 while track 4 is playing.
1.) Press the
track 5.
Skip track button once. Disc play will resume at the beginning of
2.) The CD player will skip ahead to the next track each time the
Skip track
button is pressed. Repeatedly pressing the Skip track button makes the CD
player skip ahead through the disc track by track. Once the beginning of the last
track is reached the CD player advance to the first track.
To skip to the previous track on a disc
For example to skip back to the beginning of track 3 while track 4 is playing.
1.) Press the
track 3.
Skip track button twice. Disc play will resume at the beginning of
2.) The CD player will skip back one track each time the
Skip track button is
pressed. If this button is pressed in the middle of a track, the CD player will skip
back to the beginning of that track. To make it skip back to the previous track
press the
Skip track button twice.
3.) Repeatedly pressing the
Skip track button makes the CD player skip back
through the disc track by track. Once the beginning of the first track is reached,
the CD player will go to the last track.
NOTES:
The
before disc playstarts. In this case the number of the selected track will be displayed
and
Skip track buttons can be used to select a desired track to play
until the PLAY/PAUSE
button is pressed.
16
SMV122_ib_060402.p65
16
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACK SEARCH
You can search through the track by holding the
or
track skip button down.
Normal play will resume when the button is released.
REPEAT DISC PLAY
Use the REPEAT button to play an entire disc or one track continuously.
Repeat The Whole Disc
1.) Press the REPEAT/MEMORY-UP button once. The “REPEAT” indicator
appears in the display.
MEMORY-UP/
REPEAT
1234
5678
9 10>
PLAY/
PAUSE
2.) Press the PLAY/PAUSE
button.
3.) The disc will then begin playing through to the end of the last track. At which point
it will automatically return to the beginning of the first track. This will continue
until the STOP button is pressed.
4.) If the REPEAT / MEMORY-UP button is pressed twice more, the “REPEAT”
indicator will disappears and repeat play will end. Normal disc play will resume
from that point.
5.) When the last track has finished playing, the CD play will Stop.
Repeat The Same Track
1.) Select the desired track by pressing the
will be shown in the display.
or
Skip track buttons. The track
2.) Press the REPEAT/MEMORY-UP button twice. The “REPEAT” indicator
flashes in the display.
MEMORY-UP/
REPEAT
1234
5678
9 10>
3.) Press the PLAY / PAUSE
button.
17
SMV122_ib_060402.p65
17
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
4.) The selected track will then begin playing through to its end. At which
point it will automaticallyreturn to the beginning of that track. This will
continue until the STOP button is pressed.
STOP
5.) If the REPEAT / MEMORY UP button is pressed once more, the “REPEAT”
indicator will disappear and, repeat play will end. Normal disc play will resume
from that point.
6.) When the last track has finished playing, the CD player will then Stop.
PROGRAMMED DISC PLAY
• It is possible to program the tracks you wish to playin a sequence of your choice.
It is not possible to enter program a disc during playback. Press the STOP
button first, then follow the instructions below.
• It is easier to use the remote control for the following settings, however you may
also use the controls on the main unit if desired.
ENTERING A PROGRAM
1.) Press the MEMORY button. “TRACK MEMORY” flashes and “P-01” will be
displayed on the display.
MEMORY
2.) Select the first desired track using the
and
Skip buttons.
3.) Press the MEMORY button. The first program selection is now stored in the
program memory. The display will now show “P-02”.
MEMORY
4.) Select the next desired track using the Forward
Buttons.
and Reverse
Skip
18
SMV122_ib_060402.p65
18
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
5.) Press the MEMORY button. Continue entering tracks in this way until all the
desired tracks are stored (up to 20 tracks).
NOTES:
• If the PLAY/PAUSE
button is pressed before the MEMORY button is
pressed to store a track, the track will not be programmed, and the disc will start
playing from the first selected track.
• Any track can be programmed to play more than once.
• Repeatedly pressing the MEMORY button will enable you to check the program
if required.
LISTENING TO PROGRAMMED TRACKS
1.) Enter all tracks you want to program into memory following the procedures on
page 18.
2.) Press the PLAY/PAUSE
first programmed track.
button. Disc play will start at the beginning of the
“TRACK MEMORY” indicator appears on the display.
1 3
78
9
TO CLEAR THE PROGRAM MEMORY
• Press MEMORY button to enter programming mode, then press the STOP
button.
• The program memory will also be cleared if the disc compartment is opened,
if the function is changed, or if the power is turned ‘Off’.
19
SMV122_ib_060402.p65
19
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
RANDOM PLAYBACK
Press the RANDOM button to play the tracks in random order. The RANDOM
indicator appears in the display and random playback will begin in the play position.
When all tracks have been played in random order, the player stops and the display
shows the total tracks and playing time.
Random playback can be selected while a disc is playing or while the player is in
the stop mode.
To cancel random playback press the RANDOM button until the RANDOM indicator
disappears.
INTRO SCAN PLAYBACK
Press the INTRO button to begin Intro Scan playback. The INTRO indicator appears
and the player will play the first 10 seconds of every track on each disc in the
player, starting with the disc that is in the play position. You can begin Intro playback
while a disc is playing or while the player is in the stop mode. After the first 10
seconds of each track have been played the player stops automatically.
To cancel Intro playback at any time press the INTRO button again. The INTRO
indicator disappears and normal playback resumes.
REMAIN FUNCTION
Press REMAIN/MODE button while CDis playing, displaychanges to disc remaining
play time, REMAIN indicator appears on display.
Press REMAIN/MODE button 2nd time, display shows Clock Time.
Press REMAIN/MODE button 3rd time, display shows “TIMER ON” time.
Press REMAIN/MODE button 4th time, display shows “TIMER OFF” time.
NOTE: IF NO BUTTON IS PRESSED IN 10 SECONDS, DISPLAY RETURNS TO
NORMAL CD PLAY TIME.
20
SMV122_ib_060402.p65
20
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESET EQUALIZER (EQ)
• This unit is equipped with a preset equalizer which has been added to enhance
your listening pleasure by altering the frequency response of the music.
• Press the Preset EQ button on main unit repeatedly to cycle through the
following equalization modes.
MUTE
• Press the MUTE button on remote control to switch off the sound, the MUTE
indicator will illuminate.
• Press MUTE again to restore the sound to the previous level. MUTE indicator
will extinguish.
STEREO HEADPHONE JACK
For private listening without disturbing others connect a set of stereo headphones
(not included) to the PHONES Jack on the back panel. The built-in speakers
automatically shut off when stereo headphones are connected to the headphone
jack. When using stereo headphones always start with the volume control set to a
low level and gradually increase until you find the desired level.
21
SMV122_ib_060402.p65
21
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ON/OFF TIMER (Remote Control Only)
This system now features a programmable timer that can turn the system ‘On’ and
‘Off’ whenever you like. To use the timer function you must first set the desired
‘Timer On’ and ‘Timer Off’ times, which can be set at Power ‘On’ or Standby modes.
SETTING THE TIMER ON/OFF TIMES
1.) Press the REMAIN/MODE button repeatedly until the display shows:
REMAIN/
MODE
AM
3.) Press the MEMORY button. The hour digits will be flashing.
MEMORY/
C-ADJ
AM
4.) Press the
/
buttons to adjust the hour.
Observe the AM/PM indicators to be sure you are
setting the hour correctly. When the desired hour
appears, press the MEMORY button again. The hour
digits remain ‘On’ and the minute digits begin to flash.
PM
5.) Press the
/
buttons to adjust the minutes. When the desired ‘turn on’
time is on the display, press the MEMORY button again. The ‘Timer On’ time
is set.
6.) Press the REMAIN/MODE button, MEMORY button
AM
and then the
hour.
/
buttons to adjust the ‘turn off’
7.) Press the MEMORY button and then the
buttons to adjust the ‘turn off’ minute.
/
PM
22
SMV122_ib_060402.p65
22
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
8.) When the desired ‘turn off’ time is on the displaypress
the MEMORY button once more. The display will
return to the normal function display. Press the
TIMER button to turn Timer ‘On’. The ‘TIMER’
indicator appears on display.
PM
9.) Press the appropriate function button to select the function you wish to hear
when the unit turns ‘On’ (TUNER or CD).Adjust the VOLUME, EQ,ANDcontrols
as desired and the press the POWER button to shut the system ‘Off’.
Note: If you selected the CD function make sure that the disc you want to hear
is in the play position. If you selected TUNER function make sure that the unit
is tuned to the desired station before shutting the system ‘Off’.
At the selected ‘turn on’ time the system will turn on to the function you selected. It
will play until it reaches the ‘turn off’ time and then shut off automatically. To shut
the system ‘Off’ immediately press the POWER button. The system shuts off but
the TIMER indicator remains in the display and the timer remains ‘On’. The system
will turn ‘On’ and ‘Off’ again at the same time every day until the timer is switched
‘Off.
SWITCHING THE TIMER ON AND OFF
Simply press the TIMER button to switch the Timer ‘On’ or ‘Off’. This can be done
even at Power ‘Off’. When the TIMER indicator appears in the display the Timer is
‘On’. When the TIMER indicator disappears, the Timer is ‘Off’.
23
SMV122_ib_060402.p65
23
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
SLEEP TIMER OPERATION (On Remote Control Only)
The Sleep Timer function allows you to operate the system for up to 90 minutes
and then shuts the power off automatically.
1.) Press POWER button to turn the system ‘On’, and press TUNER or CD to the
desired function.
2.) Press the SLEEP button on the remote control handset. The display will show
“SLEEP” and “90” for a few seconds. Then the display returns to the normal
function display but the SLEEP indicator remain ‘On’. The system will play for
90 minutes and then shut off automatically.
3.) To adjust the amount of Sleep Timer operation, press and hold the SLEEP
button. Release the button at the desired Sleep time.
90 80 70 60 50 40 30 20 10
4.) To shut the system ‘Off’ before the Sleep Timer ends, press the POWER button
at any time.
24
SMV122_ib_060402.p65
24
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall mounting Instruction:
1.) Use the metal bracket supplied with unit as template to mark anchor
hole locations, making sure that holes are leveled.
2.) Drill 3/16" holes.
3.) Insert the plastic anchor supplied with unit through the hole and tap it
until it is flush with the wall.
4.) Inset the screw and tighten the screw 1/8" away from the wall.
5.) Place the metal bracket and tighten the screws.
6.) Align the rectangular hook on the back of unit with the metal bracket
opening and slowly lower the unit to rest on the bracket.
7.) Make sure that the unit is securely attached to the bracket.
25
SMV122_ib_060402.p65
25
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
There are no user serviceable parts inside the unit. Do not attempt any adjustments other
than those described in the manual. Refer all other problems to qualified service personnel.
Compact Disc Care
•
To remove a disc from its storage case, press down on the center of the case and lift
the disc out, holding it carefully by the edges.
•
Treat the disc carefully. Handle the disc only by its edges. Never allow your fingers to
come in contact with the shiny, unprinted side of the disc.
•
•
Do not attach any tape, stickers, etc. to the disc label.
Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents or
abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
•
•
If a disc skips or gets stuck on a section of the disc, it is probably dirty or damaged
(scratched).
When cleaning the disc, wipe in straight lines from the center of the disc to the outer
edge of the disc. Never wipe in circular motions.
26
SMV122_ib_060402.p65
26
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
Care Of The Cabinet
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the front panel becomes dirty or smudged with fingerprints it may be cleaned
with a soft cloth slightly dampened with a mild soap and water solution. Never
use abrasive cloths or polishes as these will mar the finish of your unit.
Caution:
Never allow any water or other liquids to get inside the unit while cleaning.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-888-837-8370
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
H.H. SCOTT, INC.
Consumer Affairs Dept.
1901 Diplomat Drive, Farmers Branch, TX 75234.
27
SMV122_ib_060402.p65
27
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Possible Cause
Solution
Radio
Noise or sound
distorted on AM or FM
broadcasts.
Station not tuned properly for Retune the AM or FM
AM or FM.
broadcast station.
FM: FM Wire antenna is not
extended.
Extend FM Wire antenna.
AM: The bar antenna is not
positioned correctly.
You have tuned to a mono
station.
Reposition the unit until
best reception is obtained.
Select another FM stereo
station.
FM STEREO indicator
does not light.
AM or FM, no sound.
Function is not set to
TUNER.
Press TUNER button and
BAND to select AM or FM.
Increase Volume.
Volume at minimum.
Compact Disc Player
CD Player will not play. Function is not set to
CD.
Press CD button to select
CD.
CD is not installed or installed Insert CD with Iabel side
incorrectly.
out.
CD skips while playing. Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
28
SMV122_ib_060402.p65
28
4/6/2002, 17:42
Download from Www.Somanuals.com. All Manuals Search And Download.
H.H. SCOTT, INC.
LIMITED WARRANTY
What does this warranty cover? Any manufacturing defects in original material, including original parts and
workmanship, under normal use and conditions.
For how long? For a period of one (1) year from the date of original purchase in the U.S.
What will we do? If you need service under this warranty, and you provide us with the dated proof of purchase,
we will provide repair service at no charge for labor and parts at an authorized Depot Repair Facility, or replace
the product in our discretion.
How do you make your warranty claim? If it becomes necessary to repair your unit, you can obtain the name
and mailing location of a Depot Repair Facility by dialing 1-888-837-8370. You should pack your unit in a well-
padded heavy corrugated box, enclose your check or money order payable to the Depot Repair Facility in the
amount of $15.00 to cover the return shipping and handing costs, and enclose a copy of your proof of purchase
(warranty service will not be provided without a dated proof of purchase). Finally, you should ship the unit
prepaid via UPS or parcel post (insured).
What does your warranty not cover? Your warranty does not cover the following:
•
•
•
•
•
•
•
•
•
•
Damage from negligence, misuse, abuse, accident, or failure to follow operating instructions.
Use of product in a commercial application or rentals.
Changes or repairs by anyone other than an authorized Depot Repair Facility.
Damage because your unit is improperly connected to the equipment of other manufacturers.
Units on which the serial number has been defaced, modified or removed.
Damage to equipment not properly connected to the product.
Cost incurred in shipping your unit to and from an authorized Depot Repair Facility.
Ordinary adjustments which you can perform as outlined in the owner's manual.
Signal reception problems caused by external antenna or cable systems.
Products purchased, used, serviced or damaged outside of the United States.
What other limitations apply to your warranty?
THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER
ANDDOESNOT EXTENDTO SUBSEQUENT OWNERS OF THE PRODUCT. THIS WARRANTY IS VALID
ONLY INTHE UNITEDSTATES OFAMERICA.ANYAPPLICABLE IMPLIEDWARRANTIES, INCLUDING
THE WARRANTY OF MERCHANTABILITY, ARE LIMITED IN DURATION TO A PERIOD OF THE
EXPRESSED WARRANTY AS PROVIDED ABOVE BEGINNING WITH THE DATE OF ORIGINAL
PURCHASE AT RETAILANDNO WARRANTIES, WHETHER EXPRESSED OR IMPLIED, SHALLAPPLY
TO THE PRODUCT THEREAFTER. WE MAKE NO WARRANTYAS TO THE FITNESS OF THE PRODUCT
FOR ANY PARTICULAR PURPOSE OR USE.
THE EXTENT OF OUR LIABILITY UNDER THIS LIMITED WARRANTY IS THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND IN NO EVENT WILL OUR LIABILITY EXCEED THE
PURCHASE PRICE PAID BY THE PURCHASER OF THE PRODUCT. UNDER NO CIRCUMSTANCES
WILL WE BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT, INCIDENTAL, SPECIAL, OR
CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE USE OF THIS
PRODUCT.
How does state law apply to your warranty?
THIS WARRANTYGIVESYOU SPECIFIC LEGAL RIGHTS, BUTYOU MAYALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATIONS ON IMPLIED
WARRANTIES OR EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE,
SO THESE RESTRICTIONS MAY NOT APPLY TO YOU.
HH111N
29
SMV122_ib_060402.p65
29
4/6/2002, 17:43
Download from Www.Somanuals.com. All Manuals Search And Download.
H.H. SCOTT, INC.
H.H. SCOTT, INC.
Part No.: 100-5101
206-02
Printed in China
SMV122_ib_060402.p65
30
4/6/2002, 17:43
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Radio Shack Telephone 43 838 User Guide
Ranger Radio RCI 6300F HP User Guide
RCA Flat Panel Television G27701 User Guide
ResMed Oxygen Equipment AUTO 25 User Guide
RIDGID Drill R7111 User Guide
RIDGID Outdoor Storage 2032 OS User Guide
Rotel Stereo Amplifier RB 960BX User Guide
Samsung Refrigerator DA99 00478C User Guide
Seagate Computer Drive ST1000DM003 User Guide
Sears Air Compressor 919150270 User Guide