Samsung Flat Panel Television HP R4272C User Guide
Owner’s Instructions  
HP-R4272C  
HP-R5072C  
This device is a Class B digital apparatus.  
Register your product at www.samsung.com/global/register  
Download from Www.Somanuals.com. All Manuals Search And Download.  
User Instructions  
Screen Image retention  
Do not display a still image (such as on a video game) on the plasma display panel for more than  
several minutes as it can cause screen image retention. This image retention is also known as  
“screen burn”. To avoid such image retention, refer to page 49 of this manual to reduce the  
degree of brightness and contrast of the screen when displaying a still image.  
Altitude  
The PDP will not operate normally at altitudes above 6500 ft.  
Heat on the top of the PDP TV  
The top side of the product may be hot after long periods of use as heat dissipates from the panel  
through the vent hole in the upper part of the product.  
This is normal and does not indicate any defect or operation failure of the product.  
However, children should be prevented from touching the upper part of the product.  
The product is making a ‘cracking’ noise.  
A ‘cracking’ noise may occur when the product contracts or expands due to a change of  
surrounding environment such as temperature or humidity. This is normal and not a defect of the  
unit.  
Cell Defects  
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which  
require sophisticated technology to produce. However, there may be few bright or dark pixels on  
the screen. These pixels will have no impact on the performance of the product.  
Avoid operating the TV at temperatures below 5°C(41°F)  
A still image displayed too long may cause permanent damage to the PDP Panel.  
Watching the PDP TV in 4:3 format for a long period of time may leave  
traces of borders displayed on the left, right and center of the screen caused  
by the difference of light emission on the screen.  
Playing a DVD or a game console may cause similar effect to the screen.  
Damages caused by the above effect are not covered by the Warranty.  
Afterimage on the Screen.  
Displaying still images from Video games and PC for longer than a certain period of time may  
produce partial afterimages.  
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images for a  
long time.  
Warranty  
Warranty does not cover any damage caused by image retention.  
Burn-in is not covered by the warranty.  
Installation  
Be sure to contact an authorized service center when installing your set in a location with heavy  
dust, high or low temperatures, high humidity, and chemical substances, or where it will be  
operated for 24 hours continuously such as an airport, train station, etc.  
Failure to do so may cause serious damage to your set.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
General Information  
Picture Control  
Your New Plasma Display Panel......................8  
Remote Control Buttons ................................11  
Wall Installation Instructions..........................13  
How to assemble the Stand-Base ..................17  
Changing the Picture Standard ....................48  
Customizing the Picture Settings ....................49  
Viewing the DNIe Demonstration ..................51  
Changing the Screen Size............................52  
Viewing the Picture-in-Picture.........................54  
Selecting the Sound Source .........................60  
Setting the My Color Control Mode...............61  
Connections  
Connecting VHF and UHF Antennas ..............20  
Connecting Cable TV ..................................21  
Connecting a VCR ......................................23  
Connecting a Camcorder ............................24  
Connecting a DVD Player (480i, 480p) ........25  
Connecting a DTV Receiver (480p, 720p,  
1080i) ......................................................26  
Sound Control  
Customizing the Sound ..............................66  
Using Automatic Sound Settings ...................67  
Setting the TruSurround XT............................68  
Choosing a Multi-Channel Sound (MTS) track  
- Digital ......................................................69  
Connecting to HDMI (High Definition  
Multimedia Interface) (480p, 720p, 1080i) ..27  
Choosing a Multi-Channel Sound (MTS) track  
- Analog ....................................................70  
Connecting a Digital TV Set-Top Box (480p,  
720p, 1080i) ............................................28  
Connecting a Digital Audio System ..............29  
Connecting to an Analog Amplifier ..............30  
Using the Auto Volume ................................71  
Choosing a Digital Sound Format..................72  
Setting the On/Off Melody ..........................73  
Selecting the Internal Mute ..........................74  
Operation  
Channel Control  
Turning the TV On and Off ..........................32  
Viewing the Menus and Displays ..................36  
Memorizing the Channels ............................37  
Adding and Erasing Channels ......................39  
Setting Up Your Remote Control ....................42  
Viewing an External Signal Source................44  
Selecting the Antenna ..................................76  
Selecting Your Favorite Channels ..................77  
Labeling the Channels..................................78  
Viewing the Channel Lists ............................79  
Editing the Channel Lists ..............................80  
Fine Tuning Analog Channels ......................81  
Checking the Digital-Signal Strength ..............82  
LNA (Low Noise Amplifier) ..........................83  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a PC and Operation  
Appendix  
Connecting a PC ........................................86  
Changing the Position of the Image ..............90  
Picture Quality Adjustment............................91  
Image Reset................................................94  
Troubleshooting ........................................136  
Care and Maintenance..............................137  
Specifications............................................138  
Dimensions ..............................................139  
Time Setting  
Setting the Clock ........................................96  
Setting the On/Off Timer..............................98  
Setting the Sleep Timer ................................99  
Note  
• The information contained in this User’s  
Manual is subject to change without prior  
notice for improvement, and may vary  
depending on the version of the TV’s software  
and the regional conditions.  
Function Description  
Selecting a Menu Language ......................102  
Digital Noise Reduction..............................103  
Selecting the Film Mode ............................104  
Setting the Blue Screen ..............................105  
Using the Color Weakness Enhancement  
Option ....................................................106  
Viewing Closed Captions (On-Screen  
Text Messages) - Analog ............................107  
Viewing Closed Captions (On-Screen  
Text Messages) - Digital..............................108  
Menu Transparency Level ..........................110  
Using the Energy Saving feature ................111  
Preventing Screen Burn-in ..........................112  
Reducing the Effects of Screen Burn ............113  
Setting the Function Help............................114  
Using the V-Chip (for USA) ........................115  
Using the V-Chip (for Canada)....................121  
Electronic Program Guide ..........................129  
Remind List ..............................................133  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
General Information  
Your New Plasma Display Panel ......................................................8  
Remote Control Buttons ................................................................11  
Wall Installation Instructions ..........................................................13  
How to assemble the Stand-Base....................................................17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Your New Plasma Display Panel  
Front Panel  
Œ
´
ˇ
¨
ˆ
”
∏
Ø
Œ SOURCE button  
ˆ
(Enter) button  
Press to display all of the available video  
sources (TV, AV1, AV2, S-Video1, S-Video2,  
Component1, Component2, PC, and HDMI).  
Press to confirm a selection.  
Ø Power button  
Press to turn the TV on and off.  
´ MENU button  
Power indicator  
- Power Off : Blue  
- Power On : Off  
Displays the main on-screen menu.  
ˇ VOL +, buttons  
-
Press to increase or decrease the volume.  
Also used to select or adjust items on the  
on-screen menu.  
∏ Remote Control Sensor  
Aim the remote control towards this spot on  
the TV.  
¨ CH(  
,
) buttons  
”
Speakers  
Press CH  
or CH  
to change channels.  
Also used to move up or down in the on-screen  
menu.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Side of the TV  
COMPONENT  
Ferrite Cores  
The ferrite cores are used to attenuate  
undesired signals.  
S-Video Input  
Video Input  
When connecting cables, attach one  
of these ferrite cores to the cable near  
the connector.  
When you connect COMPONENT  
(VIDEO, AUDIO), or Side AV(VIDEO,  
AUDIO) first bind the ferrite core  
around each cable to secure it.  
Side AV  
Audio Input (L, R)  
Checking Accessories  
Once you have unpacked your TV, check to make sure that you have all the parts shown here.  
If any piece is missing or broken, call your dealer.  
Remote Control (BN59-00462A) /  
AAA Batteries  
Power Cord  
(3903-000144)  
Owner’s Instructions  
Ferrite Core for COMPONENT  
(VIDEO, AUDIO)  
Ferrite Core for Side AV  
(VIDEO, AUDIO)  
Anynet Cable  
(BN39-00518A)  
(3301-001305)  
(3301-001201)  
The following parts are sold separately and are available at most electronics stores.  
S-VIDEO Cable  
PC Cable  
HDMI Cable  
HDMI/DVI cable  
Component Cables (RCA)  
PC Audio Cable  
Optical Cable  
Coaxial Cable  
Antenna Cable  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear Panel  
Œ POWER IN  
” COAXIAL DIGITAL AUDIO OUT  
Connect the supplied power cord.  
Connect to a Digital Audio component.  
’ Anynet  
´ SERVICE ONLY  
Please refer to the Anynet Owner’s  
Instruction. This jack is for connecting to  
other Samsung Anynet-enabled devices.  
Connector for service only.  
ˇ HDMI/DVI IN  
Connect to the HDMI jack of a device with  
HDMI output.  
˝ COMPONENT IN 1, 2  
Video (Y/PB/PR) and audio (L-AUDIO-R)  
component inputs.  
These inputs can also be used as a DVI  
connection with separate analog audio inputs.  
An optional HDMI/DVI cable will be  
necessary to make this connection.  
When using the optional HDMI/DVI adapter,  
the DVI analog audio inputs on your TV allow  
you to receive left and right audio from your  
DVI device. (Not compatible with PC)  
Ô ANT (75Ω)  
75Ω Coaxial connector for Antenna/Cable  
Network.  
AV IN (AUDIO-L/R)  
Audio inputs for external devices, such as  
a camcorder or VCR.  
¨ DVI AUDIO IN (AUDIO-L/R)  
Connect to the DVI audio output jack of an  
external device.  
Ò S-VIDEO  
Video input for external devices with an  
S-Video output, such as a camcorder or VCR.  
ˆ PC IN  
Connect to the video output jack on your PC.  
Ú AUDIO OUT  
Audio outputs for external devices.  
Ø PC AUDIO IN  
Connect to the audio output jack on your PC.  
Æ VIDEO  
Video input for external devices, such as  
a camcorder or VCR.  
∏ OPTICAL DIGITAL AUDIO OUT  
Connect to a Digital Audio component.  
Note  
• Please be sure to match the color coded input terminals and cable jacks.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Buttons  
Remote Control  
Œ POWER button  
Turns the TV on and off.  
´ GUIDE button  
Press to display the on-screen Electronic Program Guide (EPG).  
ˇ ANTENNA button  
Press to select “Air” or “Cable”.  
¨ Number buttons  
ˆ
-
button  
Press to select additional channels (digital and analog)  
being broadcast by the same station. For example, to select channel  
“54-3”, press “54”, then press “-” and “3”.  
Ø MUTE button  
Press to mute the TV sound.  
∏ VOL (Volume) buttons  
Use it to adjust volume.  
” Anynet button  
Runs the Anynet view functions and sets up Anynet devices.  
Please refer to the Anynet Owner’s Instruction.  
’ MENU button  
Displays the main on-screen menu.  
˝ ENTER button  
Confirms a selection.  
Ô FAV.CH button  
Press to switch to your favorite channels.  
CH LIST button  
Displays the channel list.  
Ò MODE button  
Selects a target device to be controlled by the Samsung remote control  
(i.e., TV, STB, VCR, CABLE, or DVD).  
Ú PRE-CH button  
Tunes to the previous channel.  
Æ SOURCE button  
Press to display all of the available video sources (TV, AV1, AV2, S-Video1,  
S-Video2, Component1, Component2, PC, and HDMI).  
ı CH (Channel) buttons  
Use it to switch channels.  
˜ INFO button  
Press to display information on the TV screen.  
¯ EXIT button  
Press to exit the menu.  
˘ Up/Down/Left/Right buttons  
Control the cursor in the menu.  
Continued...  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
¿ P.MODE button  
Adjust the TV picture by selecting one of the preset factory settings (or  
select your personal, customized picture settings).  
¸ S.MODE button  
Select Sound effect.  
˛ E.SAVING button  
Press to adjust screen brightness according to surrounding environment.  
(Refer to page 111)  
◊ P.SIZE button  
Select Picture size.  
DNIe button  
Activates DNIe Demo. (Refer to page 51)  
≠ MTS button  
Press to choose stereo, mono or Separate Audio Program  
(SAP broadcast).  
– SET button  
Used during set up of this Samsung remote control, so that it will work  
compatibly with other devices (VCR, Cable Box and DVD).  
— PIP button  
Activates picture in picture.  
÷ PIP control buttons  
CH  
,
: Displays the available channels in sequence.  
(These buttons change channels in the PIP window only.)  
® CAPTION button  
Controls the caption decoder.  
∑ VCR, DVD control buttons  
Controls VCR tape or DVD disc functions: Stop, Rewind, Play/Pause,  
and Fast Forward.  
µ RESET button  
If your remote control is not functioning properly, take out the batteries  
and press the reset button for about 2~3 seconds.  
Re-insert the batteries and try using the remote control again.  
Installing the Batteries in Your Remote Control  
Slide the back cover to  
Install two AAA size  
Slide the cover back into  
1 open the battery  
2 batteries. Make sure to  
3 place.  
compartment of the remote  
control.  
match the “+” and “-” ends  
of the batteries with the  
diagram inside the  
compartment.  
Remote Control Operation Range  
You can use your remote control within a distance of 23 feet and an angle of 30 degrees  
from the left and right sides of the TV’s remote control receiver.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wall Installation Instructions  
Refer to the correct installation guide according to your wall bracket.  
Installation Notes  
Contact a technician for installing the wall bracket.  
1
2
3
Samsung Electronics is not responsible for any damage to the product or injury to yourself  
or others if you elect to perform the wall installation.  
This product is for installing on cement walls. The product may not stay in place when  
installed on plaster or wood.  
Parts (Wall attachment panel is sold separately. Check with your dealer.)  
Only use the components and accessories shipped with the panel.  
Wall Bracket  
Hinge  
Accessories  
Plastic Hanger : 4  
Screw  
: 11  
Screw  
: 4  
1
Left : 1  
Right : 1  
Anchor : 11  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to assemble the Wall Mount Bracket  
Insert and tighten the Captive Screw in the direction of the arrow.  
When done, mount the wall bracket on the wall.  
1
2
Captive Screw  
Wall Bracket  
Hinge (Left)  
There are two hinges  
(left and right). Use the  
correct one.  
Hinge (Right)  
Before drilling into the wall, check if the  
length between the two locking holes at  
the back of the product is correct. If the  
length is too short or long, loosen all or  
some of the 4 screws on the wall  
Check the installation diagram and  
mark the drill points on the wall.  
Use the 5.0 mm bit to drill holes deeper  
than 35 mm. Fix each anchor in the  
corresponding hole. Match each of the  
brackets and hinge holes to the  
3
bracket to adjust the length.  
corresponding anchor holes and insert  
and tighten the 11 screws  
.
Length between the  
two locking holes  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fixing the TV panel to the wall attachment panel bracket  
The shape of the product may vary depending on the model. (The assemblies of the plastic  
hanger and the screw are the same)  
Remove the 4 screws on the back of the product.  
1
Insert the screw  
into the plastic hanger. (See the figure below)  
2
3
• Mount the product on the wall bracket and make sure it is properly fixed to the left and  
right plastic hangers.  
• Be careful when installing the product on the bracket as fingers can be caught in the holes.  
• Make sure the wall bracket is securely fixed to the wall, or the product may not stay in  
place after installation.  
Tighten the 4 screws in step 2 (plastic  
hanger + screw ) to the rear holes of  
the product.  
Remove safety pin (#) and insert the 4  
product holders into the corresponding  
bracket holes (!). Then place the  
product (@) so that it is firmly fixed to  
the bracket. Make sure to reinsert and  
tighten the safety pin (#) to securely  
hold the product to the bracket.  
4
PDP  
Wall Bracket Wall  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Adjust Mounting Angle  
Note : Adjust the bracket angle to -2° before installing it on the wall.  
1. Fix the product to the wall bracket.  
Make sure to use the top center,  
and not the left or the right side of  
the product to adjust the angle.  
2. Hold the product at the top in the center and pull it  
forward (direction of the arrow) to adjust the angle.  
(See the figure to the right)  
3. You can adjust the bracket angle between -2° and 15°.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to assemble the Stand-Base  
Using the 4 screws for securing the stand pegs and the monitor, firmly attach the monitor  
to the stand pegs. (The exterior of the set may be different than the picture.)  
1
Warning  
Firmly secure the stand to  
the TV before moving it,  
as the stand may fall and  
could cause serious injury.  
Two or more people should carry the TV. Never lay the TV on the floor because of possible damage to the screen.  
Always store the TV upright.  
➤
➤
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Connections  
Connecting VHF and UHF Antennas ..............................................20  
Connecting Cable TV....................................................................21  
Connecting a VCR........................................................................23  
Connecting a Camcorder..............................................................24  
Connecting a DVD Player (480i, 480p)..........................................25  
Connecting a DTV Receiver (480p, 720p, 1080i) ..........................26  
Connecting to HDMI (High Definition Multimedia Interface)  
(480p, 720p, 1080i) ..................................................................27  
Connecting a Digital TV Set-Top Box (480p, 720p, 1080i) ..............28  
Connecting a Digital Audio System ................................................29  
Connecting to an Analog Amplifier ................................................30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting VHF and UHF Antennas  
Antennas with 75-ohm Round Leads  
If your antenna looks like this:  
it has 75-ohm round leads.  
Plug the antenna lead into the ANT 2 IN (AIR IN)  
on the TV.  
Use an antenna cable. (Sold Separately)  
1
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Cable TV  
You can connect different cable systems to your TV, including cable without a Cable box, and cable  
with a Cable box that descrambles some or all channels.  
Cable without a Cable Box  
Plug the incoming cable into the ANT 1 IN (CABLE IN)  
on the TV.  
Use an antenna cable. (Sold Separately)  
1
Cable with a Cable Box that Descrambles All Channels  
Find the cable connected to the ANTENNA OUT  
terminal on your Cable box. This terminal might be  
labeled “ANT OUT”, “VHF OUT” or simply “OUT”.  
1
Cable Box  
Connect the cable to the ANT 1 IN (CABLE IN) on the  
TV.  
2
Use an antenna cable. (Sold Separately)  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cable with a Cable Box that Descrambles Some (But Not All) Channels  
To complete this connection you will need a two-way splitter, an RF (A/B) switch, and four coaxial  
cables (which you can buy from your Samsung dealer or any electronics store).  
Find and disconnect the cable that is  
connected to the ANTENNA IN terminal  
1
of your Splitter. This terminal might  
be labeled “ANT IN”, “VHF IN” or  
simply, “IN”. Connect this cable to a  
two-way splitter.  
Connect a coaxial cable between an  
OUT terminal of the splitter and the  
IN terminal of the Cable box.  
2
Connect a coaxial cable between the  
ANTENNA OUT terminal of the Cable  
box and the B-IN terminal of the RF  
(A/B) switch.  
3
Connect a coaxial cable between the  
other OUT terminal of the Cable box  
and the A-IN terminal of the RF (A/B)  
switch.  
4
Connect the last coaxial cable between  
the OUT terminal of the RF (A/B)  
switch and the ANT 1 IN (CABLE IN)  
on the TV.  
5
After you've made this connection, set the A/B switch to the “A” position for normal viewing.  
Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to  
“B”, you will need to tune your Set-Top Box to the Cable box's output channel, which is usually  
channel 3 or 4.)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a VCR  
Connecting a VCR to the Video or S-Video/Audio jack  
TV Rear Panel  
VCR  
Power cord  
Audio cable  
Video cable  
S-Video cable  
How to Connect  
Connect the Video/Audio cables between the VIDEO or S-VIDEO/AUDIO input jacks on the  
TV and VIDEO or S-VIDEO/AUDIO output jacks on the VCR.  
(Note: For better video, use an S-Video cable.)  
Note  
• Please be sure to match the color coded input terminals and cable jacks.  
Videotape Playback:  
1. Turn on your TV.  
2. Press the SOURCE button to select “Video (AV1 or AV2)” or “S-Video (S-Video1 or S-Video2)”.  
3. Turn on your VCR, insert a videotape and press the Play button.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a Camcorder  
Viewing camcorder tapes  
TV Rear Panel  
Camcorder  
Power cord  
Audio cable  
Video cable  
S-Video cable  
How to Connect  
Connect a Video/Audio cable between the VIDEO or S-VIDEO/AUDIO input jacks on the TV  
and the VIDEO or S-VIDEO/AUDIO output jacks on the camcorder.  
(Note: For better video, use an S-VIDEO cable.)  
Note  
• Please be sure to match the color coded input terminals and cable jacks.  
Viewing Tapes  
1. Turn on your TV.  
2. Press the SOURCE button to select “Video (AV1 or AV2)” or “S-Video (S-Video1 or S-Video2)”.  
3. Turn on your camcorder and set it to video mode. (For details, refer to your camcorder  
owner’s instructions.)  
4. Set the IN/OUT switch on your camcorder to OUT.  
5. Insert the tape into the camcorder and press the Play button.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DVD Player (480i, 480p)  
Playing DVD  
TV Rear Panel  
DVD Player  
Power cord  
Component cable  
Audio cable  
How to Connect  
Connect the Y, PB, PR (COMPONENT1, 2) input jacks on the TV to the Y, PB, PR output jacks  
on the DVD player using a component cable.  
1
2
Connect the AUDIO L/R (COMPONENT1, 2) input jacks on the TV to the AUDIO output  
jacks on the DVD player using a audio cable.  
Note  
• Please be sure to match the color coded input terminals and cable jacks.  
To Play DVD:  
1. Turn on your TV.  
2. Press the SOURCE button to select “Component 1” or “Component 2”.  
3. Turn on your DVD player, insert a DVD disc and press the Play button.  
• For an explanation of component video, see your DVD player’s owner’s instructions.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a DTV Receiver (480p, 720p, 1080i)  
This TV displays the optimum picture in 720p mode.  
Watching DTV  
TV Rear Panel  
DTV Receiver  
Power cord  
Component cable  
Audio cable  
HDMI/DVI cable  
How to Connect  
Connect the cable or antenna to the antenna input jack on the DTV.  
1
2
Connect the Y, PB, PR (COMPONENT1, 2) or HDMI input jack on the TV to the Y, PB, PR or  
DVI output jacks on the DTV receiver using a component or HDMI/DVI cable.  
Connect the AUDIO L/R (COMPONENT1, 2 or DVI AUDIO IN) input jacks on the TV with  
the AUDIO output jacks on the DTV receiver using an audio cable.  
3
Note  
• Please be sure to match the color coded input terminals and cable jacks.  
To Watch DTV:  
1. Turn on your TV.  
2. Turn on your DTV receiver.  
• For an explanation of component video, see your DTV receiver owner’s instructions.  
3. Press the SOURCE button to select “Component1”, “Component2” or “HDMI”.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to HDMI (High Definition  
Multimedia Interface) (480p, 720p, 1080i)  
Watching DTV  
TV Rear Panel  
Power cord  
HDMI cable  
DTV Set-Top Box  
How to Connect  
Connect the cable or antenna to the antenna input jack on the DTV.  
1
2
Connect the HDMI input jack on the TV with the HDMI output jack on the DTV Set-Top Box  
using an HDMI cable.  
Note  
• Please make sure the HDMI source’s power is on before selecting HDMI from the “Source List”  
on the TV.  
To Watch DTV:  
1. Turn on your TV.  
2. Turn on your DTV receiver.  
• For an explanation of HDMI video, see your DTV receiver owner’s instructions.  
3. Press the SOURCE button to select “HDMI”.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a Digital TV Set-Top Box  
(480p, 720p, 1080i)  
By inputting a high-bandwidth digital content protection High-Definition picture source  
to the HDMI input jack on the TV, High-Definition pictures can be displayed on the  
screen in their digital form.  
Connecting to HDMI (High Definition Multimedia Interface)/DVI Compatible  
TV Rear Panel  
Power cord  
DTV Set-Top Box  
From cable  
or Antenna  
HDMI/DVI cable  
Audio cable  
How to Connect  
Connect the DVI AUDIO (L, R) input jacks on the TV with the AUDIO output jacks on the  
Set-Top Box using an audio cable.  
1
Note  
• Use analog stereo audio inputs when using the HDMI input with a device that outputs  
DVI instead of HDMI.  
Connect the HDMI input jack on the TV and the DVI output jack on the Set-Top Box  
2
using an HDMI/DVI cable.  
Note  
• The HDMI IN jack is not compatible with PC.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a Digital Audio System  
There are many types of digital audio systems on the market today.  
A simplified illustration of an audio system is shown below. For more information, see your  
audio system owner’s manual.  
TV Rear Panel  
Power cord  
Digital Audio System  
Coaxial cable  
Optical cable  
How to Connect  
If your audio system has a coaxial digital audio input, connect to the “COAXIAL” output jack  
on the TV.  
1
If your audio system has a optical digital audio input, connect to the “OPTICAL“ output jack  
on the TV.  
Be certain to remove the black cover from the optical output before inserting the cable.  
2
If your system has both coaxial and optical digital audio inputs, SAMSUNG recommends  
you use the optical digital output on the TV.  
3
Do not connect both optical and coaxial cables. This may damage your audio system.  
• OPTICAL: converts the electric signal into an optical light signal, and transmits it through  
glass fibers.  
• COAXIAL: The digital audio signal is received through a coaxial copper cable.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting to an Analog Amplifier  
TV Rear Panel  
Power cord  
Audio cable  
Analog Amplifier  
How to Connect  
The “AUDIO OUT (AUDIO L/R)” terminals cannot be used for external speakers.  
You must hook them up to an amplifier.  
1
When an audio amplifier is connected to the “AUDIO OUT (AUDIO L/R)” terminals:  
Decrease the gain (volume) of the audio amplifier, turn the TV’s internal mute on and adjust  
the volume level with the volume control of the amplifier.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Operation  
Turning the TV On and Off............................................................32  
Viewing the Menus and Displays ..................................................36  
Memorizing the Channels ............................................................37  
Adding and Erasing Channels ......................................................39  
Setting Up Your Remote Control ....................................................42  
Viewing an External Signal Source ................................................44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Turning the TV On and Off  
Turning the TV On and Off  
Press the POWER button on the remote control.  
The TV will be turned on and you will be able to use its features.  
You can also use the Power button on the front of the TV.  
Note  
•
If your TV isn’t turned on when the POWER button is pressed:  
Press the MODE button to check if the TV mode has been  
chosen  
.
Plug & Play Feature  
When the TV is initially powered On, basic customer settings proceed automatically and subsequently:  
Setting the language, checking the antenna input, memorizing the channels, and setting the time.  
Note  
•
The Plug & Play function operates after plugging in the TV for the first time.  
Press the POWER button on the remote control.  
The message “Menu language, Channels and Time  
will be set.” is displayed.  
Menu language, Channels  
and Time will be set.  
1
i
Press the ENTER button, then “Select the language of  
the OSD.” menu is automatically displayed.  
Start  
Plug & Play  
Press the ENTER button to enter the language.  
Press the ▲ or ▼ button to select language, then  
the ENTER button. “Select the antennas to  
memorize.” menu is automatically displayed.  
Select the language of the OSD.  
2
Menu Language  
:
English  
Spanish  
French  
Move  
Enter  
Skip  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Plug & Play  
Press the ▲ or ▼ button to memorize the channels of  
the selected connection.  
Press the ENTER button to select “Start”.  
Select the antennas to memorize.  
3
4
Air  
Start  
Cable  
Start  
Start  
Notes  
Air + Cable  
• If the antenna is connected to ANT 1 IN (CABLE IN),  
select “Cable” and if it is connected to ANT 2 IN  
(AIR IN), select “Air”.  
Move  
Enter  
Skip  
• If both ANT 1 IN and ANT 2 IN are connected,  
select the “Air + Cable”.  
Plug & Play  
Select the correct signal source (STD, HRC, and  
Select the cable system.  
IRC) by pressing the ▲ or ▼ button, then press  
.
the ENTER button  
STD  
HRC  
IRC  
Note  
•
STD, HRC, and IRC identify various types of cable  
TV systems. Contact your local cable company to  
identify the type of cable system that exists in your  
particular area. At this point the signal source has  
been selected. Proceed to “Storing Channels in  
Memory” on page 38.  
Move  
Enter  
Skip  
Plug & Play  
Auto Program in Progress.  
Cable Channel 67  
Stop  
Enter  
Skip  
Plug & Play  
The TV will begin memorizing all of the available  
channels.  
After all the available channels are stored, the Auto  
program menu reappears.  
5
Auto Program is completed.  
14 Channels were memorized.  
AIR : 9 , Cable : 5.  
Press the ENTER button at any time to interrupt the  
memorization process.  
OK  
Press the ENTER button to select OK when channel  
memorization is complete.  
Enter  
Skip  
“Set to daylight savings time.” menu is automatically  
displayed.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Press the ENTER button. Press the ▲ or ▼ button to  
select “Yes” or “No”, then the ENTER button.  
“Select the time zone in which you live” menu is  
automatically displayed.  
Plug & Play  
6
Set to daylight savings time.  
Daylight Savings Time  
: No
Yes  
Move  
Enter  
Skip  
Plug & Play  
Press the ▲ or ▼ button to highlight the time zone  
for your local area (and to move the highlight to the  
appropriate time zone on the map of the United States).  
Press the ENTER button.  
Select the time zone in which you live.  
7
8
Newfoundland  
Atlantic  
Eastern  
Central  
Mountain  
Pacific  
If you have received a digital signal, the time will  
be set automatically. If not, see page 96 to set the  
clock.  
Alaska  
Hawaii  
Move  
Enter  
Skip  
The message “Completed. Time will be updated  
automatically.” is displayed.  
Completed. Time will  
be updated automatically.  
i
When you have finished, press the ENTER button.  
OK  
• The message will automatically disappear after a few  
seconds, even if the ENTER button is not pressed.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you want to reset this feature...  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Press the ENTER button to select “Plug & Play”.  
Menu language, Channels  
and Time will be set.  
2
i
Start  
For further details on setting up options, refer to the  
previous page.  
3
Note  
• Plug and Play can only be accessed in the TV mode.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the Menus and Displays  
Your TV has a simple, easy-to-use menu system that appears on the TV screen.  
This system makes it convenient and fast to use features on the TV.  
Your TV also lets you display the status of many of your TV’s features.  
Viewing the Menus  
T V  
Input  
With the power on, press the MENU button on the  
Source List  
Edit Name  
Anynet  
: TV  
√
√
√
remote control. The main menu appears on the  
1
screen. The Input menu is selected.  
Move  
Enter  
Return  
Press the ▲ or ▼ button to move to items in the menu.  
Press the œ/√/ENTER buttons to display,  
change, or use the selected items.  
2
Press the ENTER button to enter items in the menu.  
On screen menus disappear from the screen  
automatically after about two minutes or you can press  
the MENU or EXIT button on your remote control to exit  
the menu.  
Displaying Status Information  
Press the INFO button on the remote control.  
The TV will display the Picture Mode, Sound Mode, MTS,  
V-Chip, and Current Time.  
AIR 28  
Mono  
Picture Mode : Dynamic  
Sound Mode : Custom  
MTS : Stereo  
V-Chip : Off  
12 : 00 am  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memorizing the Channels  
Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable  
channels. After the available channels are memorized, use the CH  
and CH  
buttons to scan  
through the channels. This eliminates the need to change channels by entering the channel digits.  
There are three steps for memorizing channels: selecting a broadcast source, memorizing the  
channels (automatic) and adding and deleting channels (manual).  
Selecting a broadcast source  
Before your television can begin memorizing the available channels, you must specify the type of signal  
source that is connected to the TV (i.e., an antenna or a cable system).  
T V  
Channel  
: Air  
Press the MENU button. Press the ▲ or ▼ button to select  
“Channel”, then press the ENTER button.  
Antenna  
√
√
√
√
√
√
1
2
3
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
T V  
Channel  
: Air  
Press the ▲ or ▼ button to select “Auto Program”, then  
Antenna  
√
√
√
√
√
√
press the ENTER button.  
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
Return  
Return  
T V  
Auto Program  
Press the ▲ or ▼ button to select the antenna connection,  
then press the ENTER button.  
Select the antennas to memorize  
Notes  
Air  
Cable  
Air + Cable  
Start  
Start  
Start  
• Air  
: “Air” antenna signal.  
• Cable  
: “Cable” antenna signal.  
• Air + Cable : “Air” and “Cable” antenna signals.  
Move  
Enter  
Auto Program  
Select the antennas to memorize  
• If the antenna is connected to ANT 1 IN (CABLE IN),  
select “Cable” and if it is connected to ANT 2 IN  
(AIR IN), select “Air”.  
• If both ANT 1 IN and ANT 2 IN are connected,  
select the “Air + Cable”.  
T V  
Start  
Air  
Cable  
Air + Cable  
Start  
Start  
Move  
Enter  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Storing Channels in Memory  
T V  
Auto Program  
Select the cable system.  
Select the correct signal source (STD, HRC, and  
IRC) by pressing the ▲ or ▼ button, then press  
4
.
the ENTER button  
STD  
HRC  
IRC  
Note  
•
STD, HRC, and IRC identify various types of cable  
TV systems. Contact your local cable company to  
identify the type of cable system that exists in your  
particular area. At this point the signal source has  
been selected.  
Move  
Enter  
Return  
Auto Program  
Auto Program in Progress.  
The TV begins memorizing all available stations.  
Press the ENTER button at any time to interrupt the  
memorization process.  
5
Cable Channel 67  
Press the EXIT button to exit.  
Stop  
Enter  
Note  
•
Return  
The TV must be connected to an antenna in  
order to receive digital TV signals.  
Even if a particular channel is deleted from the  
memory, you can always tune to that channel  
directly by using the number buttons on the  
remote control.  
Notes  
•
All available DTV and analog channels are automatically stored in memory when channels are  
selected by directly accessing channels.  
• It takes approximately 3 to 10 minutes to memorize channels.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adding and Erasing Channels  
To add channels that were not memorized (or to delete unwanted channels from memory):  
T V  
Channel  
: Air  
Press the MENU button.  
Press the ▲ or ▼ button to select “Channel”, then  
press the ENTER button.  
Antenna  
√
√
√
√
√
√
1
2
3
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
† More  
Move  
Enter  
Return  
T V  
Channel  
: Air  
Press the ▲ or ▼ button to select “Add/Delete”, then  
Antenna  
√
√
√
√
√
√
press the ENTER button.  
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
† More  
Move  
Enter  
Return  
Add / Delete  
Not in memory  
Repeatedly pressing the ENTER button will alternate  
between add channel and delete channel.  
Air 16  
Press ENTER to add the channel.  
Add  
Press the CH  
or CH  
button to switch to the  
appropriate channel, then repeat above.  
Press the EXIT button to exit.  
Change  
Enter  
Return  
Add / Delete  
Air 16  
In memory  
Press ENTER to delete the channel.  
Delete  
Change  
Enter  
Return  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing Channels  
Using the Channel Buttons  
Press the CH  
or CH  
button to change channels.  
or CH  
When you press the CH  
button, the TV changes channels  
in sequence. You will see all the channels that the TV has memorized.  
(The TV must have memorized at least three channels.)  
You will not see channels that were either erased or not memorized.  
Directly Accessing Channels  
Press the number buttons to go directly to a channel. For example, to select  
channel 27, press “2” then “7”.  
When you use the number buttons, you can directly select channels that  
were either erased or not memorized. To change to single-digit channels  
(0~9) faster, press “0” before the single digit. (For channel “4” press “0”,  
then “4”.)  
Note  
•
For quick channel change, press the number buttons and, then press  
ENTER button.  
Using the PRE-CH button to select the previous channel  
Press the PRE-CH button. The TV will switch to the last channel viewed.  
To quickly switch between two channels that are far apart, tune to one  
channel, then use the number button to select the second channel.  
Then, use the PRE-CH button to quickly alternate between them.  
Adjusting the Volume  
Using the Volume Buttons  
Press the VOL  
or VOL  
button to increase or decrease the volume.  
Using Mute  
Using the MUTE Button  
At any time, you can temporarily cut off the sound using the MUTE button.  
Mute  
Press the MUTE button and the sound cuts off. The word “MUTE” will  
1
2
appear in the lower-left corner of the screen.  
To turn mute off, press the MUTE button again, or simply press the  
VOL  
or VOL  
button.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the “-” Button  
The “ ” button is used to select stations that broadcast both a digital and analog signal.  
For example, for Channel 7  
then “1”.  
-1 (digital), press “7”, then “ ”,  
DTV Cable  
7 - 1  
KYW-HD  
HD  
For channel 7-2 (analog), press “7”, then “ ”, then “2”.  
DTV Cable  
7 - 2  
R
SD  
Multi  
Notes  
•
HD indicates the TV is receiving a Digital High Definition signal.  
SD indicates the TV is receiving a Standard Definition signal.  
•
For quick channel change, press the number buttons, then press the ENTER button.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting Up Your Remote Control  
Your TV comes equipped with a universal remote control. In addition to controlling the TV, the universal  
remote control can also operate a VCR, Cable box, DVD, and some Samsung Set-top boxes (even if your  
VCR, Cable box and DVD are made by manufacturers other than Samsung).  
●
Note :  
The remote control might not be compatible with all DVD Players, VCRs, Cable boxes,  
and Set-Top Boxes.  
Setting Up the Remote to Operate Your VCR, Cable box or DVD player  
Turn off your VCR (or Cable box, DVD player).  
1
Press the MODE button. The Mode is changed whenever  
MODE button is pressed.  
2
Press the SET button on your TV's remote control.  
3
Using the number buttons on your remote control, enter  
three digits of the VCR (or Cable box, DVD player) code  
4
listed on page 43 of this manual for your brand of VCR (or  
Cable box, DVD). Make sure you enter three digits of the  
code, even if the first digit is a “0”. (If more than one code  
is listed, try the first one.)  
Press the POWER button on the remote control. Your VCR  
(or Cable box, DVD) should turn on if your remote is set up  
5
correctly. If your VCR (or Cable box, DVD) does not turn on  
after setup, repeat steps 2, 3, and 4, but try one of the  
other codes listed for your brand of VCR (or Cable box,  
DVD). If no other codes are listed, try each code, 000  
through 089 (or Cable box: 000 through 077, DVD player:  
000 through 008).  
Note  
• When your remote control is in “VCR”, “CABLE”, or “DVD” mode, the VCR control buttons (STOP,  
REW, PLAY/PAUSE, and FF) still operate your VCR.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remote Control Codes  
VCR Codes  
Cable Box Codes  
DVD Codes  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing an External Signal Source  
Use the remote control to switch between viewing signals from connected equipment, such as  
VCR, DVD, Set-Top Box, and the TV source (broadcast or cable).  
Setting the Signal Source  
T V  
T V  
T V  
Input  
Press the MENU button.  
Source List  
Edit Name  
Anynet  
: TV  
√
√
√
Press the ENTER button to select “Input”.  
1
Quick way to access viewing an external signal source :  
Just press the “SOURCE” button on the remote control.  
➤
➤
Move  
Enter  
Source List  
Return  
Return  
Return  
Press the ENTER button to select “Source List”.  
TV  
AV1  
AV2  
S-Video1  
S-Video2  
2
3
4
:
:
:
:
:
----  
----  
----  
----  
----  
Component 1  
† More  
Move  
Enter  
Source List  
Press the ▲ or ▼ button to select signal source, then  
press the ENTER button.  
TV  
AV1  
AV2  
S-Video1  
S-Video2  
Component 1  
† More  
:
:
:
:
:
----  
----  
----  
----  
----  
Move  
Enter  
Press the MENU button to exit.  
Notes  
• When you connect equipment to the TV, you can choose between the following sets of jacks:  
AV1, AV2, S-Video1, S-Video2, COMPONENT 1, COMPONENT 2, PC, or HDMI on the  
TV’s rear panel.  
• Before selecting an input source, connect an external device first.  
• HDMI input can only be selected when the external device is turned on and connected via HDMI.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assigning Names to External input mode  
T V  
T V  
T V  
Input  
Press the MENU button.  
Press the ENTER button to select “Input”.  
Source List  
Edit Name  
Anynet  
: TV  
√
√
√
1
Move  
Enter  
Edit Name  
Return  
Press the ▲ or ▼ button to select “Edit Name”, then  
press the ENTER button.  
AV1  
AV2  
S-Video1  
S-Video2  
Component 1  
:
:
:
:
:
----  
----  
----  
----  
----  
√
√
√
√
√
2
† More  
Move  
Enter  
Return  
Edit Name  
Press the ENTER button.  
Press the ▲ or ▼ button to select external device,  
AV1  
AV2  
S-Video1  
S-Video2  
Component 1  
:
:
:
:
:
----  
3
then press the ENTER button.  
VCR  
DVD  
D-VHS  
Cable STB  
• You can select the VCR, DVD, D-VHS, Cable STB,  
HD STB, Satellite STB, PVR STB, AV Receiver,  
DVD Receiver, GAME, Camcorder, DVD Combo,  
PC, VOD STB, or TV.  
HD STB  
Satellite STB  
† More  
PVR STB  
†
Move  
Enter  
Return  
• Set other signal sources (AV2, S-Video1, S-Video2,  
Component 1, Component 2, PC, or HDMI) using the  
same method as listed above.  
Press the MENU button to exit.  
4
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Picture Control  
Changing the Picture Standard ......................................................48  
Customizing the Picture Settings ....................................................49  
Viewing the DNIe Demonstration ..................................................51  
Changing the Screen Size ............................................................52  
Viewing the Picture-in-Picture..........................................................54  
Selecting the Sound Source ..........................................................60  
Setting the My Color Control Mode................................................61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Picture Standard  
You can select the type of picture which best corresponds to your viewing requirements.  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
Mode  
: Dynamic  
Press the ENTER button again to select “Mode”.  
Mode  
√
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
100  
45  
75  
55  
G 50  
R 50  
: Cool2  
√
Move  
Enter  
Return  
Mode  
Press the ENTER button.  
Mode  
: Dynamic  
Press the ▲ or ▼ button to select the desired picture  
mode (Dynamic, Standard, Movie, Custom), then press  
the ENTER button.  
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
Standard  
55  
Movie  
Custom  
G 50  
R 50  
: Cool2  
Move  
Enter  
Return  
Press the MENU button to exit.  
• Choose Dynamic for viewing the TV during the day or when there is bright light in the room.  
• Choose Standard for the standard factory settings.  
• Choose Movie when viewing the movie.  
• Choose Custom if you want to adjust the settings according to personal preference  
(see “Customizing the Picture Settings”, page 49).  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Picture Settings  
You can use the on-screen menus to change the “Contrast”, “Brightness”, “Sharpness”, “Color”,  
“Tint”, and “Color Tone” according to personal preference. You can select “Standard” which  
automatically recalls your personalized picture settings.  
T V  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
Quick way to access the picture setting: Just press the “P.MODE”  
button on the remote control.  
➤
➤
: Off  
†
More  
Move  
Enter  
Return  
Mode  
: Dynamic  
Press the ENTER button to select “Mode”.  
Mode  
√
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
100  
45  
75  
55  
G 50  
R 50  
: Cool2  
√
Move  
Enter  
Return  
Mode  
Press the ENTER button.  
Mode  
: Dynamic  
Press the ▲ or ▼ button to select the desired picture  
mode (Dynamic, Standard, Movie, Custom), then press  
the ENTER button.  
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
Standard  
55  
Movie  
Custom  
G 50  
R 50  
: Cool2  
Move  
Enter  
Return  
Mode  
Press the ▲ or ▼ button to select a particular option  
(Contrast, Brightness, Sharpness, Color, or Tint), then  
press the ENTER button.  
Mode  
: Custom  
√
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
80  
50  
50  
50  
Press the œ or √ button to decrease or increase the  
value of a particular item.  
G 50  
R 50  
: Normal  
√
• You can also select these options (Contrast,  
Brightness, Sharpness, Color, or Tint) by pressing  
the ▲ or ▼ button.  
Move  
Enter  
Return  
80  
Contrast  
Notes  
• “Tint” doesn’t operate in HDMI or any Component modes.  
• The Tint cannot be adjusted while watching Digital TV.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T V  
Mode  
: Custom  
Press the ENTER button to return to “Mode”.  
Press the ▲ or ▼ button to select “Color Tone”, then  
press the ENTER button.  
Mode  
√
√
5
6
Contrast  
Brightness  
Sharpness  
Color  
80  
50  
50  
50  
Tint  
Color Tone  
Reset  
G 50  
R 50  
: Normal  
Move  
Enter  
Return  
T V  
Mode  
Press the ▲ or ▼ button to select a particular option  
(Cool2, Cool1, Normal, Warm1, or Warm2), then press  
the ENTER button.  
Mode  
: Custom  
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
80  
Cool2  
Cool1  
Normal  
Warm1
:
Press the MENU button to exit.  
G 50  
Warm2  
Move  
Enter  
Return  
Resetting the Picture Settings to the Factory Defaults  
T V  
Mode  
: Custom  
To return the factory defaults, select “Reset” by pressing  
Mode  
√
80  
50  
50  
50  
the ▲ or ▼ button.  
Press the ENTER button.  
7
Contrast  
Brightness  
Sharpness  
Color  
Tint  
Color Tone  
Reset  
• The previously adjusted settings will be reset to the  
factory defaults.  
G 50  
R 50  
: Normal  
√
Move  
Enter  
Return  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the DNIe Demonstration  
This TV includes the DNIe function so as to provide a high visual quality.  
If you set DNIe Demo to On, you can view the applied DNIe and normal pictures on the screen,  
for demonstration purposes. Using this function, you can view the difference in the visual quality.  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
Quick way to select DNIe: Simply press the “DNIe” button under the  
cover of the remote control.  
➤
➤
: Off  
†
More  
Move  
Enter  
Return  
Picture  
: Dynamic  
Press the ▲ or ▼ button to select “DNIe Demo”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: 16:9  
: On  
:
Off  
On  
: Off  
†
More  
Move  
Enter  
Return  
Picture  
: Dynamic  
Press the ▲ or ▼ button to select “Off” or “On”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: 16:9  
: On  
: Off  
On  
• Off : Switches off the DNIe Demo mode.  
• On : Switches on the DNIe Demo mode.  
: Off  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
DNIe Demo  
Off  
On  
Note  
TM  
• DNIe (Digital Natural Image engine)  
This feature brings you a more detailed image with 3D noise reduction and detail,  
contrast and white enhancement.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Screen Size  
Screen size selection depends on the type of video input.  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
select “Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
Quick way to change the Screen size: Simply press the P.SIZE button  
under the cover of the remote control.  
➤
➤
: Off  
†
More  
Move  
Enter  
Return  
T V  
Picture  
: Dynamic  
: 16:9  
Press the ▲ or ▼ button to select “Size”, then press the  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
ENTER button.  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Size  
Return  
T V  
Press the œ or √ button to select the screen size you  
want, then press the ENTER button.  
16:9  
Panorama Zoom1  
Zoom2  
4:3  
Move  
Enter  
Return  
Press the MENU button to exit.  
Notes  
•
If you watch a still image or the 4:3 (Normal) mode for a long time (over 2 hours),  
an image may be burned onto the screen.  
•
View the TV in 16:9 (Wide) or Panorama mode as much as possible.  
• 16:9  
: Sets the picture to 16:9 wide mode.  
• Panorama  
• Zoom1  
• Zoom2  
• 4:3  
: Use this mode for the wide aspect ratio of a panoramic picture.  
: Magnifies the size of the picture on the screen.  
: Expands the Zoom1 format picture.  
: Sets the picture to 4:3 normal mode.  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
When you press the P.SIZE button under the cover of the remote control, the TV’s screen mode should  
appear in sequence. The screen displays in this order: 16:9, Panorama, Zoom1, Zoom2, 4:3.  
Note  
• If you watch a still image or the 4:3 mode for a long time (over 2 hours), an image may be burned  
onto the screen. View the TV in 16:9 or Panorama mode as much as possible.  
16:9  
Zoom2  
Sets the picture to 16:9 wide mode.  
The screen size when the Zoom1 screen is  
vertically enlarged.  
16:9  
Zoom2  
Move  
Panorama  
4:3  
Converts regular 4:3 aspect ratio screen to  
wide screen.  
Sets the picture to 4:3 normal mode.  
Panorama  
4:3  
Zoom1  
The screen size when Wide screen is  
vertically enlarged.  
Zoom1  
Move  
Notes  
•
In TV, VIDEO, S-VIDEO, and COMPONENT(480i, 480p) modes, all screen modes can be selected.  
(16:9 Panorama Zoom1 Zoom2 4:3).  
➞
➞
➞
➞
• In TV(DTV), COMPONENT(720p, 1080i), PC, HDMI modes, only 16:9 & 4:3 modes can be selected.  
•
•
In Zoom1, Zoom2 modes, you can move the picture on screen by pressing the ▲ or ▼ button.  
Picture size will not change when PIP size is Double.  
53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the Picture-in-Picture  
Selecting the PIP Screen  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
: 16:9  
: On  
: Off  
Quick way to access the PIP mode: Simply press the “PIP” button under  
the cover of the remote control.  
➤
➤
: Off  
†
More  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
Move  
Enter  
PIP  
Return  
2
3
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: Off  
: TV  
√
√
Press the ENTER button, then press the ▲ or ▼  
button to select “On”. The PIP image will appear in  
the corner of the screen.  
• Pressing the ▲ or ▼ button will alternate between  
“On” and “Off”.  
:
:
√
√
√
: Air 3  
Note  
Enter  
PIP  
Return  
• If the PIP On/Off will not function, check if the  
V-Chip Lock (refer to page 116) is On. PIP does  
not function when the V-Chip Lock is set to On.  
Change the setting to Off and try it again.  
PIP  
Source  
Swap  
: On  
: TV  
√
√
Size  
Position  
PIP Channel  
:
:
√
√
√
: DTV Air 3 - 0  
Press the MENU button to exit.  
4
PIP Settings  
Move  
Enter  
Return  
A : Analog  
D : Digital  
O : PIP and swap operate  
X : PIP doesn’t operate  
TV  
Main screen  
AV(A)  
S-Video(A) Component(A)  
PC  
HDMI(D)  
Digital  
(ATSC)  
Analog  
PIP screen  
TV  
X
X
X
O
X
O
X
Analog  
X
Digital  
(ATSC)  
O
O
O
X
X
X
X
X
X
O
O
O
X
O
O
O
X
X
X
O
O
O
X
AV(A)  
S-Video(A)  
Component(A)  
X
X
X
X
X
X
X
X
PC  
HDMI(D)  
O
O
O
X
X
O
X
Note  
• This TV has only one tuner and does not allow you to watch one TV channel in the main screen and  
another channel in the PIP screen.  
54  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting an External Signal  
You can use PIP to view a signal from an external source, such as a VCR.  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
“Picture”, then press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
1
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
PIP  
Return  
T V  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
2
:
:
√
√
√
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Return  
T V  
Press the ▲ or ▼ button to select “Source”, then press  
the ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
:
TV  
3
AV1  
:
AV2  
S-Video1  
S-Video2  
:
:
Component 1  
:
Component 2  
HDMI  
Enter  
Move  
Return  
Press the ▲ or ▼ button to cycle through all of the  
available signal sources:  
“TV”, “AV1”, “AV2”, “S-Video1”, “S-Video2”,  
“Component1”, “Component2”, or “HDMI”.  
4
The signal from these inputs will not appear if you  
have not connected any equipment to the TV's  
respective input jacks.  
Press the MENU button to exit.  
5
Notes  
• The same source cannot be selected on both the main and sub screens. However, the same source  
can be selected on both the main and sub screens for TV.  
55  
• PC is not available in PIP picture.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Swapping the Contents of the PIP and Main Image  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
“Picture”, then press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
1
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
PIP  
Return  
T V  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
2
:
:
√
√
√
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Return  
T V  
Press the ▲ or ▼ button to select “Swap”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
3
• The image in the PIP window will appear on the  
main screen, and vice versa. (Refer to page 54)  
:
:
√
√
√
: DTV Air 3 - 0  
Note  
•
Move  
Enter  
Return  
If main picture is in PC mode, Swap is not  
available.  
Press the MENU button to exit.  
4
56  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Size of the PIP Window  
T V  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
PIP  
Return  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
2
:
:
√
√
√
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Return  
Return  
Return  
Press the ▲ or ▼ button to select “Size”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
3
:
:
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Press the ▲ or ▼ button to select option you want, then  
press the ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
4
:
:
: DTV Air 3 - 0  
Move  
Enter  
Press the MENU button to exit.  
5
57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Location of the PIP Image  
T V  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
PIP  
Return  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
2
:
:
√
√
√
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Return  
Return  
Return  
Press the ▲ or ▼ button to select “Position”, then press  
the ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
3
:
:
: - 0  
Move  
Enter  
PIP  
Press the ▲ or ▼ button to select the PIP position you  
want, then press the ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
4
:
:
: - 0  
Move  
Enter  
Press the MENU button to exit.  
5
Note  
• The Double1 (  
) and Double2 (  
) mode cannot be selected in Position.  
58  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the PIP Channel  
T V  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
: 16:9  
: On  
: Off  
Quick way to change the PIP channel: Just press the “CH  
“ or  
➤
➤
“CH  
” button under the cover of the remote control.  
: Off  
†
More  
Move  
Enter  
PIP  
Return  
Press the ▲ or ▼ button to select “PIP”, then press the  
ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
√
√
2
3
4
5
:
:
√
√
√
: DTV Air 3 - 0  
Move  
Enter  
PIP  
Return  
Press the ▲ or ▼ button to select “PIP Channel”, then  
press the ENTER button.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
:
:
▲
DTV Air 3 - 0  
: ▲
Move  
Enter  
PIP  
Return  
Press the ▲ or ▼ button to change the channel that  
appears in the PIP window.  
PIP  
Source  
Swap  
Size  
Position  
PIP Channel  
: On  
: TV  
:
:
▲
DTV Air 4 - 0  
: ▲
Move  
Enter  
Return  
Press the MENU button to exit.  
59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Sound Source  
You can use this feature to hear sound from the main or sub (PIP) picture.  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to  
select “Sound”, then press the ENTER button.  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “Sound Select”, then  
…
More  
press the ENTER button.  
Digital Output  
Melody  
Sound Select  
: Dolby Digital  
: On  
:
Main  
Sub  
Move  
Enter  
Return  
Press the ▲ or ▼ button to select “Main” or “Sub”, then  
press the ENTER button.  
Press the MENU button to exit.  
60  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the My Color Control Mode  
My Color Control allows you to adjust colors according to your preference, by adjusting skin, sky,  
and grass tones using the predefined settings (Standard, Custom, Red, Green, Blue, Yellow, Pink,  
White) without affecting other colors on the screen.  
Using the My Color Control Function in the Easy Control Menu  
Skin, sky and grass tones are easily adjustable to suit your preferences.  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
“Picture”, then press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
1
2
3
4
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
T V  
My Color Control  
: Custom  
Press the ▲ or ▼ button to select “My Color Control”,  
Easy Control  
Detail Control  
√
√
then press the ENTER button.  
Move  
Enter  
Return  
Press the ENTER button to select “Easy Control”.  
Original  
Custom  
Easy Control  
Pink  
White  
Standard  
Custom  
√
√
Move  
Enter  
Return  
Press the œ or √ button to select the setting among the  
various picture settings. The original picture (before  
adjustment) is shown on the left side, while the selected  
mode is shown on the right side.  
Original  
Red  
Easy Control  
There are eight My Color Control modes: Standard, Custom, Red, Green,  
Blue, Yellow, Pink, White.  
➤
➤
Red  
Green  
Blue  
Yellow  
√
√
Move  
Enter  
Return  
Press the MENU button to exit the menu.  
5
Note  
• Pressing the ENTER button on the remote control for 3 seconds when there is no OSD on the  
screen will display the My Color Control menu.  
61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
My Color Control Mode Characteristics  
Using My Color Control mode, you can enjoy vivid colors as shown below.  
Red  
Green  
Standard  
Standard Picture.  
Emphasizes Reds.  
Emphasizes Mild Greens.  
➤
➤
➤
➤
➤
➤
Blue  
Pink  
Yellow  
Emphasizes Clear Blues.  
Emphasizes Yellows.  
Emphasizes Warm Skin Colors.  
➤
➤
➤
➤
➤
➤
White  
Emphasizes Whites.  
➤
➤
Note  
• Images shown above may differ from the actual adjustment on the screen.  
These images are presented for illustrative purposes.  
62  
Download from Www.Somanuals.com. All Manuals Search And Download.  
My Color Control Custom Settings  
Users can adjust the 6 My Color Control colors (Red, Green, Blue, Yellow, Pink, and White).  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
My Color Control  
: Custom  
Press the ▲ or ▼ button to select “My Color Control”,  
then press the ENTER button.  
Easy Control  
Detail Control  
√
√
Move  
Enter  
Return  
Detail Control  
Press the ▲ or ▼ button to select “Detail Control”, then  
press the ENTER button.  
Red  
Green  
Blue  
Yellow  
Pink  
White  
Reset  
50  
50  
50  
50  
60  
50  
Move  
Enter  
Return  
Press the ▲ or ▼ button to select the desired color and  
then press the ENTER or √ button.  
Original  
Adjusted  
The original picture (before adjustment) is shown on the left side,  
while the picture after adjustment is shown on the right side, and an  
adjustment bar on the bottom of the screen.  
➤
➤
Detail Control  
Adjust  
Red  
Move  
50  
Return  
Press the œ or √ button to adjust the settings.  
5
6
• Press the ▲ or ▼ button to select other colors.  
Press the ENTER or MENU button to confirm the changes  
and return to the previous menu.  
63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Resetting the My Color Control Colors to the Factory Defaults  
To return to the factory default settings for My Color Control colors, use the Reset function.  
T V  
T V  
T V  
T V  
Picture  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: Dynamic  
: 16:9  
: On  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: Off  
: Off  
†
More  
Move  
Enter  
Return  
My Color Control  
: Custom  
Press the ▲ or ▼ button to select “My Color Control”,  
then press the ENTER button.  
Easy Control  
Detail Control  
√
√
Move  
Move  
Move  
Enter  
Return  
Detail Control  
Press the ▲ or ▼ button to select “Detail Control”, then  
press the ENTER button.  
Red  
Green  
Blue  
Yellow  
Pink  
White  
Reset  
50  
50  
50  
50  
60  
50  
Enter  
Return  
Detail Control  
Press the ▲ or ▼ button to select “Reset” and press the  
ENTER button.  
Red  
Green  
Blue  
Yellow  
Pink  
White  
Reset  
50  
50  
50  
50  
60  
50  
Enter  
Return  
The previously adjusted My Color Control Colors will be  
reset to the factory defaults.  
5
6
Press the MENU button to exit the menu.  
64  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Sound Control  
Customizing the Sound ................................................................66  
Using Automatic Sound Settings ....................................................67  
Setting the TruSurround XT ............................................................68  
Choosing a Multi-Channel Sound (MTS) track - Digital......................69  
Choosing a Multi-Channel Sound (MTS) track - Analog ....................70  
Using the Auto Volume..................................................................71  
Choosing a Digital Sound Format ..................................................72  
Setting the On/Off Melody ..........................................................73  
Selecting the Internal Mute ............................................................74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customizing the Sound  
The sound settings can be adjusted to suit your personal preferences.  
(Alternatively, you can use one of the “automatic” settings. See next page.)  
T V  
Sound  
: Custom  
Press the MENU button. Press the ▲ or ▼ button to select  
“Sound”, then press the ENTER button.  
Mode  
Equalizer  
√
√
√
√
√
√
1
2
3
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Equalizer  
Return  
T V  
Press the ▲ or ▼ button to select “Equalizer”, then  
press the ENTER button.  
+
0
-
+
0
-
L
R
Balance  
100Hz 300Hz 1K 3K 10K  
Move  
Adjust  
Return  
Press the œ or √ button to select a particular frequency  
to adjust. Press the ▲ or ▼ button to increase or  
decrease the level of the particular frequency.  
Press the MENU button to exit.  
4
Notes  
• If you make any changes to the equalizer settings, the sound mode is automatically switched  
to the custom mode.  
• L/R Sound Balance Adjustment  
To adjust the sound balance of the L/R speakers.  
• Bandwidth Adjustment (100, 300, 1K, 3K, 10K)  
To adjust the level of different bandwidth frequencies.  
66  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using Automatic Sound Settings  
Your TV has automatic sound settings (“Standard”, “Music”, “Movie”, and “Speech”) that are  
preset at the factory. Or, you can select “Custom,” which automatically recalls your personalized  
sound settings.  
T V  
T V  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
select “Sound”, then press the ENTER button.  
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
Quick way to access the picture setting: Just press the “S.MODE”  
button on the remote control.  
➤
➤
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
Press the ENTER button to select “Mode”.  
Standard  
:
Music  
Mode  
Equalizer  
Movie  
Speech  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
Internal Mute  
:
Custom  
: Off  
: Off  
†
More  
Move  
Enter  
Sound  
Return  
Press the ▲ or ▼ button to select “Standard”, “Music”,  
“Movie”, “Speech”, or “Custom” sound setting,  
then press the ENTER button.  
Standard  
:
Music  
Mode  
Equalizer  
Movie  
Speech  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
Internal Mute  
:
Custom  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
• Choose Standard for the standard factory settings.  
• Choose Music when watching music videos or concerts.  
• Choose Movie when watching movies.  
• Choose Speech when watching a show that is mostly dialog (i.e., news).  
• Choose Custom to recall your personalized settings (see “Customizing the Sound”, page 66).  
67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the TruSurround XT  
TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel  
content over two speakers. TruSurround delivers a compelling, virtual surround sound experience  
through any two-speaker playback system, including internal television speakers. It is fully  
compatible with all multichannel formats.  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to select  
“Sound”, then press the ENTER button.  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “SRS TruSurround XT”,  
Mode  
Equalizer  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Custom  
then press the ENTER button.  
: Off  
3D Mono  
Stereo  
: Off  
Internal Mute  
: Off  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to change the setting (Off, 3D  
Mono, or Stereo), then press the ENTER button.  
Mode  
Equalizer  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Custom  
: Off  
3D Mono  
Stereo  
: Off  
Internal Mute  
: Off  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
68  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choosing a Multi-Channel  
Sound (MTS) track - Digital  
The digital-TV transmission system is capable of simultaneous transmission of many audio tracks (for  
example, simultaneous translations of the program into foreign languages). The availability of these  
additional “multitracks” depends upon the program.  
T V  
T V  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
select “Sound”, then press the ENTER button.  
1
2
3
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
Quick way to access the MTS menu: Just press the “MTS” button  
under the cover of the remote control. You can listen in a  
language other than the favorite language by pressing the MTS  
button.  
➤
➤
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Return  
Multi-Track Options  
Press the ▲ or ▼ button to select “Multi-Track  
Options”, then press the ENTER button.  
Preferred Language : English  
√
√
Multi-Track Sound  
: Stereo  
Enter  
Return  
Multi-Track Options  
Press the ENTER button to select “Preferred  
Language”. Press the ▲ or ▼ button to choose the  
language (English, Spanish, or French) you want,  
then press the ENTER button.  
English  
Preferred Language :
Spanish  
Multi-Track Sound  
:
French  
Move  
Enter  
Return  
Press the MENU button to exit.  
4
Note  
• You can only select the language from among the actual languages broadcast by the  
broadcasting station. That is, if the current program is broadcast with a configured  
language (e.g. French), you will listen to the program in the configured Preferred Language.  
However, if the program is not broadcast with the configured language, you will listen to the  
program in the default language determined by the broadcasting station (e.g. English).  
69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choosing a Multi-Channel  
Sound (MTS) track - Analog  
Depending on the particular program being broadcast, you can listen to Mono, Stereo or SAP.  
T V  
T V  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
“Sound”, then press the ENTER button.  
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
button  
Quick way to access the MTS menu: Just press the “MTS”  
➤
➤
under the cover of the remote control  
settings.  
repeatedly to select one of the  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Return  
Multi-Track Options  
Press the ▲ or ▼ button to select “Multi-Track Options”,  
then press the ENTER button.  
Preferred Language : English  
√
√
Multi-Track Sound  
: Stereo  
Move  
Enter  
Return  
Multi-Track Options  
Press the ENTER button to select “Multi-Track Sound”.  
Press the ▲ or ▼ button to select a setting you want,  
then press the ENTER button.  
Preferred Language : English  
Mono  
Multi-Track Sound  
:
Stereo  
SAP  
Move  
Enter  
Return  
Press the MENU button to exit.  
• Choose “Mono” for channels that are broadcasting in mono, or if you are having difficulty  
receiving a stereo signal.  
• Choose “Stereo” for channels that are broadcasting in stereo.  
• Choose “SAP” to listen to the Separate Audio Program, which is usually a foreign-language  
translation.  
70  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Auto Volume  
Each broadcasting station has its own signal conditions, which can make it necessary to adjust the  
volume every time the channel is changed. “Auto Volume” lets you automatically adjust the volume  
of the desired channel by lowering the sound output when the modulation signal is high or by  
raising the sound output when the modulation signal is low.  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to select  
“Sound”, then press the ENTER button.  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “Auto Volume”, then  
Mode  
Equalizer  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Custom  
press the ENTER button.  
: Off  
:
Off  
On  
:
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “On”, then press the  
ENTER button.  
Mode  
Equalizer  
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Custom  
: Off  
• Pressing the ▲ or ▼ button will alternate  
between “On” and “Off”.  
:
Off  
On  
:
Internal Mute  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choosing a Digital Sound Format  
Digital sound can be output from the rear panel connector on your TV. The digital sound outputs  
are connectors labeled “Optical” and “Coaxial”. After connecting a digital-audio component, you  
must specify the transmission format (Dolby or PCM, as appropriate to your digital audio  
component).  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to select  
“Sound”, then press the ENTER button.  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
1
2
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “Digital Output”, then  
press the ENTER button.  
Press the ▲ or ▼ button to select “Dolby Digital” or  
“PCM”, then press the ENTER button.  
…
More  
Digital Output  
Melody  
Sound Select  
:
Dolby Digital  
PCM  
:
: Main  
Move  
Enter  
Return  
Press the MENU button to exit.  
3
Note  
• In Digital TV mode, both Dolby Digital and PCM can be selected, while only PCM can be  
selected in HDMI mode.  
Manufactured under license from Dolby Laboratories.  
“Dolby” and the double-D symbol are trademarks of Dolby  
Laboratories.  
72  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the On/Off Melody  
A melody sound can be set to come on when the TV is powered On or Off.  
T V  
Sound  
: Custom  
Press the MENU button. Press the ▲ or ▼ button to  
select “Sound”, then press the ENTER button.  
Mode  
Equalizer  
√
√
√
√
√
√
1
2
3
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Sound  
Return  
T V  
Press the ▲ or ▼ button to select “Melody”, then press  
the ENTER button. Press the ▲ or ▼ button to  
…
More  
Digital Output  
Melody  
Sound Select  
: Dolby Digital  
: Off  
On  
select “On” or “Off”, then press the ENTER button.  
:
Move  
Enter  
Return  
Press the MENU button to exit.  
73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Internal Mute  
Sound output from the TV speakers is muted.  
T V  
Sound  
Press the MENU button. Press the ▲ or ▼ button to select  
“Sound”, then press the ENTER button.  
Mode  
Equalizer  
: Custom  
√
√
√
√
√
√
1
2
3
4
SRS TruSurround XT  
Multi-Track Options  
Auto Volume  
: Off  
: Off  
: Off  
Internal Mute  
†
More  
Move  
Enter  
Return  
Return  
Return  
T V  
Sound  
: Custom  
Press the ▲ or ▼ button to select “Internal Mute”, then  
press the ENTER button.  
Mode  
Equalizer  
SRS TruSurround XT : Off  
Multi-Track Options  
Auto Volume  
Internal Mute  
: Off  
:
Off  
†
On  
More  
Move  
Enter  
T V  
Sound  
Press the ▲ or ▼ button to select “On”, then press the  
ENTER button.  
Mode  
Equalizer  
SRS TruSurround XT : Off  
Multi-Track Options  
Auto Volume  
Internal Mute  
: Custom  
• Pressing the ▲ or ▼ button will alternate between  
“On” and “Off”.  
: Off  
:
Off  
†
On  
More  
Move  
Enter  
Press the MENU button to exit.  
Notes  
• When Internal Mute is set to “On”, Sound menus except Multi-track Options, Digital Output cannot  
be adjusted.  
• The monitor and digital audio outputs (Optical, Coaxial) remain enabled.  
• The VOL +, VOL - and Mute buttons do not operate when the Internal Mute is set to On.  
74  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Channel Control  
Selecting the Antenna ..................................................................76  
Selecting Your Favorite Channels ..................................................77  
Labeling the Channels ..................................................................78  
Viewing the Channel Lists..............................................................79  
Editing the Channel Lists ..............................................................80  
Fine Tuning Analog Channels ........................................................81  
Checking the Digital-Signal Strength ..............................................82  
LNA (Low Noise Amplifier)............................................................83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Antenna  
T V  
Channel  
: Air  
Press the MENU button. Press the ▲ or ▼ button to select  
“Channel”, then press the ENTER button.  
Antenna  
√
√
√
√
√
√
1
2
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
T V  
Channel  
Press the ENTER button to select “Antenna”.  
Press the ▲ or ▼ button to select “Air” or “Cable”,  
Air  
:
Cable  
Antenna  
Auto Program  
Add / Delete  
Favorite Channels  
Name  
then press the ENTER button.  
Fine Tune  
†
More  
Move  
Enter  
Return  
Notes  
• If the antenna is connected to ANT 1 IN  
(CABLE IN), select “CABLE” and if it is  
connected to ANT 2 IN (AIR IN), select “Air”.  
or  
• If both ANT 1 IN and ANT 2 IN are connected,  
select the antenna input you want.  
If the antenna input is not selected properly,  
noise may appear on the screen.  
76  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting Your Favorite Channels  
You can store your favorite channels for each available input source (such as TV and Cable box).  
Then, when you press the FAV.CH button on the remote control, the TV displays only the favorite  
channels you previously stored, allowing you to quickly and easily find frequently watched channels.  
To Store Your Favorite Channels:  
T V  
T V  
T V  
Channel  
: Air  
Press the MENU button.  
Antenna  
√
√
√
√
√
√
Press the ▲ or ▼ button to select “Channel”, then  
press the ENTER button.  
1
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
Favorite Channels  
Press the ▲ or ▼ button to select “Favorite Channels”,  
Select All  
Clear All  
Air 6  
Air 7  
Air 9  
Air 11  
Air 13  
Air 14  
Air 16  
then press the ENTER button.  
2
Press the ▲ or ▼ button to select a channel as  
a favorite channel, then press the ENTER button.  
Press the ENTER button again to deselect the  
selected channel.  
†
Move  
Enter  
Return  
Favorite Channels  
Select All  
Press the MENU button to exit.  
Air 6  
Air 7  
Air 9  
Air 11  
Air 13  
Air 14  
Air 16  
3
Clear All  
†
Move  
Enter  
Return  
Notes  
• Only memorized channels can be set as favorite channels.  
• Select All : Press to select all channels.  
Clear All : Press to clear all channels.  
To View Your Favorite Channels:  
Press the FAV.CH button repeatedly to jump from one  
favorite channel to another.  
77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Labeling the Channels  
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”, “PBS2”,  
“CNN1”, etc.) A label consists of five fields, where each field is a letter, a number or a blank.  
When the INFO button is pressed, the channel label will appear next to the channel number.  
T V  
T V  
T V  
Channel  
: Air  
Press the MENU button.  
Press the ▲ or ▼ button to select “Channel”, then  
press the ENTER button.  
Antenna  
√
√
√
√
√
√
1
2
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
Name  
Press the ▲ or ▼ button to select “Name”, then press the  
ENTER button.  
Air 6  
Air 7  
Air 9  
Air 11  
Air 13  
†
Clear  
Clear  
Clear  
Clear  
Clear  
Press the ▲ or ▼ button to select the channel to be  
assigned to a new name, then press the ENTER button.  
Press the ▲ or ▼ button to select a letter, a number  
or a blank (Results in this sequence: A...Z, 0...9,  
Move  
Enter  
Return  
+, -, , /, blank).  
*
Name  
Press the √ button to switch to the next field, which  
will be selected.  
…
Clear  
Clear  
Clear  
Clear  
Clear  
Air 6  
Air 7  
Air 9  
Air 11  
Air 13  
A
†
Select a second letter or digit by pressing the ▲ or  
▼ button, as above.  
Repeat the process to select the last three digits.  
When you have finished, press the ENTER button  
to assign the new name.  
†
Move  
Adjust  
Return  
• To clear the entered channel name, move to “Clear”  
by using the œ/√ button and press the ENTER.  
Press the MENU button to exit.  
3
Note  
• The names of digital broadcasting channels are automatically assigned and thus cannot be  
assigned by users.  
78  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing the Channel Lists  
You can display a list of all channels or your favorite channels.  
T V  
Channel  
: Air  
Press the MENU button.  
Antenna  
√
√
√
√
√
√
Press the ▲ or ▼ button to select “Channel”, then press  
1
2
3
Auto Program  
Add / Delete  
Favorite Channels  
Name  
the ENTER button.  
Quick way to view the Channel Lists: Just press the “CH LIST”  
button on the remote control.  
➤
➤
Fine Tune  
†
More  
Move  
Enter  
Return  
T V  
Channel List  
Press the ▲ or ▼ button to select “Channel List”, then  
All  
Edit  
Favorite  
√
√
√
press the ENTER button.  
Move  
Enter  
Return  
Channel List  
Press the ▲ or ▼ button to select “All” or “Favorite”, then  
press the ENTER button.  
To toggle between your favorite channels or all channels,  
use the yellow button on the remote control.  
All  
2-1  
4
6
8
10  
12  
13-3 TV #3  
62  
69-98 NCAM-H..  
13-4 TV #4  
17  
19  
23  
• Red button : Press to display the previous channel  
list page.  
28  
13-1 TV #1  
13-2 TV #1  
32-10  
44  
Green button : Press to display the next channel  
Yellow button : Press to toggle between your favorite  
channels or all channels.  
Favorite  
Watch  
Exit  
Move  
Return  
Blue or EXIT button : Press to exit.  
Alternate method :  
Press the CH LIST button on the remote control to display a list  
of channels.  
79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Editing the Channel Lists  
You can edit channels to be added or deleted.  
T V  
Channel  
: Air  
Press the MENU button.  
Antenna  
√
√
√
√
√
√
Press the ▲ or ▼ button to select “Channel”, then press  
1
2
3
Auto Program  
Add / Delete  
Favorite Channels  
Name  
the ENTER button.  
Fine Tune  
†
More  
Move  
Enter  
Return  
T V  
Channel List  
Press the ▲ or ▼ button to select “Channel List”, then  
All  
Edit  
Favorite  
√
√
√
press the ENTER button.  
Move  
Enter  
Return  
Channel List  
Press the ▲ or ▼ button to select “Edit”, then press the  
ENTER button.  
Edit  
2-1  
13-3 TV #3  
62  
69-98 NCAM-H..  
4
13-4 TV #4  
6
17  
8
19  
10  
23  
12  
28  
13-1 TV #1  
13-2 TV #1  
32-10  
44  
Add All Delete All  
Delete  
Move  
Return  
Channel List  
Press the ▲ or ▼ button to select Channel and the  
ENTER button. Then, the channel can be deleted or  
added. The deleted channel will be dim in the channel  
list.  
Edit  
4
5
2-1  
13-3 TV #3  
62  
69-98 NCAM-H..  
4
13-4 TV #4  
6
17  
8
19  
10  
12  
23  
• Red button : Press to display the previous channel  
list page.  
Green button : Press to display the next channel  
Yellow button : Press to add all channels deleted.  
Blue button : Press to delete all channels memorized.  
28  
13-1 TV #1  
13-2 TV #1  
32-10  
44  
Add All Delete All  
Add  
Move  
Return  
Press the MENU button to exit.  
80  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fine Tuning Analog Channels  
Use fine tuning to manually adjust a particular channel for optimal reception.  
T V  
Channel  
Press the MENU button. Press the ▲ or ▼ button to select  
“Channel”, then press the ENTER button.  
Antenna  
: Air  
√
√
√
√
√
√
1
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
Fine Tune  
Press the ▲ or ▼ button to select “Fine Tune”, then press  
the ENTER button.  
AIR 4  
2
3
4
5
0
Reset  
Save  
Adjust  
Return  
Fine Tune  
Press the œ or √ button to adjust the fine tuning.  
To store the fine tuning setting in the TV’s memory, press  
the ENTER button.  
AIR 4  
Fine Tuned  
10  
Reset  
Save  
Adjust  
Return  
Fine Tune  
To reset the fine tuning setting, press the ▼ button  
to select “Reset”, then press the ENTER button.  
AIR 4  
0
Reset  
Enter  
Move  
Return  
Press the MENU button to exit.  
Notes  
Only analog TV channels can be fine tuned.  
*
•
•
“ ” will appear next to the name of fine-tuned channels.  
81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking the Digital-Signal Strength  
Unlike analog channels, which can vary in reception quality from “snowy” to clear, digital (HDTV)  
channels have either perfect reception quality or you will not receive them at all. So, unlike analog  
channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve  
the reception of available digital channels.  
T V  
Channel  
: Air  
Press the MENU button.  
Press the ▲ or ▼ button to select “Channel”, then press  
the ENTER button.  
Antenna  
√
√
√
√
√
√
1
2
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
T V  
Signal Strength  
Press the ▲ or ▼ button to select “Signal Strength”,  
then press the ENTER button.  
If the signal strength meter indicates that the signal  
is weak, physically adjust your antenna to increase  
the signal strength.  
Continue to adjust the antenna until you find the  
best position with the strongest signal.  
Return  
Press the MENU button to exit.  
3
82  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LNA (Low Noise Amplifier)  
If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception  
(a low-noise preamplifier boosts the incoming signal).  
T V  
T V  
T V  
Channel  
: Air  
Press the MENU button. Press the ▲ or ▼ button to select  
Antenna  
√
√
√
√
√
√
“Channel”, then press the ENTER button.  
1
2
3
4
Auto Program  
Add / Delete  
Favorite Channels  
Name  
Fine Tune  
†
More  
Move  
Enter  
Return  
Return  
Return  
Channel  
Press the ▲ or ▼ button to select “LNA”, then press the  
ENTER button.  
…
More  
Channel List  
Signal Strength  
LNA  
: Off  
On  
Move  
Enter  
Channel  
Press the ▲ or ▼ button to select “On” or “Off”, then  
press the ENTER button.  
…
More  
Channel List  
Signal Strength  
LNA  
: Off  
On  
Move  
Enter  
Press the MENU button to exit.  
Notes  
• LNA functions only when antenna is set to AIR and the settings will be stored separately in  
each channel. (See “Selecting the Antenna” on page 76.)  
• If the picture is noisy with the LNA set to On, select Off.  
• The LNA setting must be made separately for each channel.  
83  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Connecting a PC and Operation  
Connecting a PC..........................................................................86  
Changing the Position of the Image................................................90  
Picture Quality Adjustment ............................................................91  
Image Reset ................................................................................94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting a PC  
Connection to a Macintosh computer may require an adapter.  
TV Rear Panel  
Power cord  
Audio cable  
PC cable  
PC  
Connecting a PC (15p D-SUB) to the TV  
Connect a PC cable between the PC Output jack on the PC and the RGB input jack (PC IN)  
1
2
on the TV.  
Connect a Audio cable between the Audio jack on the PC and the Audio input jacks (PC AUDIO IN)  
on the TV.  
Notes  
• Please be sure to match the color coded input terminals and cable jacks.  
• A PC will not operate when connected with a HDMI/DVI cable.  
To watch the PC screen:  
1. Turn on your TV.  
2. Press the SOURCE button on the remote control or SOURCE button on the front panel  
to select “PC”.  
3. Turn on your PC and check for PC system requirements. (Refer to pages 88 and 89 for PC  
system requirements.)  
4. Adjust the PC screen. (Refer to pages 90 and 92.)  
86  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting up Your TV (Plug and Play)  
Our adoption of the new VESA Plug and Play solution eliminates complicated and time consuming  
setup. It allows you to install your monitor in a Plug and Play compatible system, without the usual setup  
hassles and confusion. Your PC system can easily identify and configure itself for use with your TV.  
This TV automatically tells the PC system its Extended Display Identification data (EDID) using Display  
Data Channel (DDC) protocols.  
87  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Your PC Software (Windows only)  
The Windows display-settings for a typical computer are shown below. But the actual screens on your  
PC will probably be different, depending upon your particular version of Windows and your particular  
video card. But even if your actual screens look different, the same, basic set-up information will apply  
in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.)  
1. Right click the mouse on the Windows  
Desktop, then click on Properties.  
The Display Dialog-Box will be displayed.  
2. Click on Settings, then set the Display Mode  
with reference to the Display Modes Table.  
You do not need to change the Colors settings.  
3. Click on Advanced. A new settings dialog box  
will be displayed.  
4. Click on the Monitor tab, then set the  
Screen Refresh Rate with reference to the  
Display Modes Table. Set the Vertical  
Frequency and Horizontal Frequency  
individually if you can do so instead of setting  
the Screen Refresh Rate.  
5. Press the OK button, close the window, then  
press the OK button on the Display Registration  
Information window. Automatic re-booting may  
commence at this moment.  
2
3
6. Shutdown the PC, and connect it to your TV.  
(See page 86)  
• The actual screens on your PC may look  
different, depending on your particular  
version of Windows and the type of your PC.  
• When you use your TV as a PC monitor, it  
supports Colors up to 32 bits.  
• In this case, the display on the TV may look  
different depending on your particular version  
4
5
of Windows or the PC manufacturer.  
• When connecting a PC (including the DVI  
connection), you must set it to the display  
settings that are supported by the TV.  
Otherwise, the message Out of input  
range will be displayed.  
Continued...  
88  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Note  
Both screen position and size will vary, depending on the type of PC monitor and its resolution.  
The table below shows all of the display modes that are supported:  
Resolution  
Vertical  
Horizontal  
Vertical  
Polarity  
Horizontal  
Polarity  
Video Signal  
HP-R4272C HP-R5072C  
(Dot X Line) Frequency (Hz) Frequency (KHz)  
640 X 350  
720 X 400  
640 X 480  
70.086  
70.087  
59.940  
70.000  
72.809  
75.000  
56.250  
60.317  
70.000  
72.188  
75.000  
60.004  
70.069  
72.000  
75.029  
59.855  
60.015  
31.469  
31.469  
31.469  
35.000  
37.861  
37.500  
35.156  
37.879  
43.750  
48.077  
46.875  
48.363  
56.476  
57.672  
60.023  
44.772  
47.712  
P
N
N
N/P  
N
N
N/P  
P
N/P  
P
P
N
N
N/P  
P
P
P
N
P
N
N/P  
N
N
N/P  
P
N/P  
P
P
N
N
N/P  
P
N
P
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
800 X 600  
IBM PC / AT  
Compatible  
1024 X 768  
1280 X 720  
1360 X 768  
• The interlace mode is not supported.  
• The TV operates abnormally if a non-standard video format is selected.  
• The table above conforms to IBM/VESA regulations and is based on using the Analog Input.  
• A “✔” mark means that this mode can be supported.  
Notes  
• The PC text quality of HP-R4272C is optimum in XGA mode (1024 x 768@60Hz).  
• The PC text quality of HP-R5072C is optimum in WXGA mode (1360 x 768@60Hz).  
• When this TV is used as a PC display, 32-bit color is supported.  
• Depending on the manufacturer, your PC display screen might appear different.  
(and depending on your particular version of Windows.)  
Check your PC instruction book for information about connecting your PC to a TV.  
• If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 48.4KHz (horizontal).  
• In some cases, abnormal signals (such as stripes) might appear on the TV screen when the PC power  
is turned off (or if the PC is disconnected). If so, press the SOURCE button on the remote control or  
SOURCE button on the front panel to enter the VIDEO mode. Also, make sure that the PC is connected.  
• Connect only a PC monitor to the monitor output port while viewing the PC screen.  
(Otherwise, random signals might appear).  
89  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Changing the Position of the Image  
After connecting the TV to your PC, adjust the position of the screen if it is not well-aligned.  
Preset:  
• Press the SOURCE button to select “PC.”  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
3
4
5
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
PC  
Return  
Press the ▲ or ▼ button to select “PC”, then press the  
ENTER button.  
Image Lock  
Position  
Auto Adjustment  
Image Reset  
√
√
Move  
Enter  
Return  
Return  
Return  
Position  
Press the ▲ or ▼ button to select “Position”, then press  
the ENTER button.  
Move  
Enter  
T V  
Position  
Adjust the position of screen by pressing the  
▲/▼/œ/√ button.  
Move  
Enter  
Press the MENU button to exit.  
90  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Picture Quality Adjustment  
Picture Automatic Adjustment  
Preset:  
•
Press the SOURCE button to select “PC”.  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
PC  
Return  
T V  
Press the ▲ or ▼ button to select “PC”, then press the  
ENTER button.  
Image Lock  
Position  
Auto Adjustment  
Image Reset  
√
√
2
3
Move  
Enter  
Return  
Press the ▲ or ▼ button to select “Auto Adjustment”,  
then press the ENTER button.  
The message “Auto Adjustment in progress. Please wait.”  
appears on the screen and the picture adjustments are  
automatically activated.  
Auto Adjustment in progress. Please wait.  
91  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Coarse Adjustment  
Preset:  
•
Press the SOURCE button to select “PC”.  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
PC  
Return  
Press the ▲ or ▼ button to select “PC”, then press the  
ENTER button.  
Image Lock  
Position  
Auto Adjustment  
Image Reset  
√
√
2
3
Move  
Enter  
Return  
Image Lock  
Press the ENTER button to select “Image Lock”.  
Coarse  
Fine  
50  
0
Move  
Enter  
Return  
50  
Press the ENTER button again to select “Coarse”.  
Remove picture noise (vertical stripes) on the screen  
by pressing the œ or √ button. (If Coarse is not set  
properly, vertical stripes will appear on the screen.)  
Coarse  
4
5
• Press the ▲ or ▼ button to select another item.  
Press the MENU button to exit.  
92  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fine Tuning (Fine)  
Preset:  
•
Press the SOURCE button to select “PC”.  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
PC  
Return  
Press the ▲ or ▼ button to select “PC”, then press the  
ENTER button.  
Image Lock  
Position  
Auto Adjustment  
Image Reset  
√
√
2
3
4
5
Move  
Enter  
Return  
Image Lock  
Press the ENTER button to select “Image Lock”.  
Coarse  
Fine  
50  
0
Move  
Enter  
Return  
0
Press the ▲ or ▼ button to select “Fine”, then press the  
ENTER button.  
Remove picture noise on the screen by pressing the  
œ or √ button. (If Fine is not set properly, noise will  
appear on the screen.)  
Fine  
• Press the ▲ or ▼ button to select another item.  
Press the MENU button to exit.  
93  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Image Reset  
Preset:  
•
Press the SOURCE button to select “PC”.  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
PC  
Return  
T V  
Press the ▲ or ▼ button to select “PC”, then press the  
ENTER button.  
Image Lock  
Position  
Auto Adjustment  
Image Reset  
√
√
2
3
Move  
Enter  
Return  
Press the ▲ or ▼ button to select “Image Reset”, then  
press the ENTER button.  
The message “Image Reset is completed.” appears on  
the screen.  
Image Reset is completed.  
• The previously adjusted settings will be reset to the  
factory defaults.  
94  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Time Setting  
Setting the Clock.......................................................................96  
Setting the On/Off Timer ...........................................................98  
Setting the Sleep Timer ..............................................................99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Clock  
Setting the clock is necessary in order to use the various timer features of the TV.  
Also, you can check the time while watching the TV. (Just press the INFO button.)  
Option 1: Setting the Clock Manually  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
2
3
4
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Time  
Return  
T V  
T V  
T V  
Press the ▲ or ▼ button to select “Time”, then press the  
--  
/
--  
/
----  
/
-- :-- --  
ENTER button. Press the ENTER button to select “Clock”.  
Clock  
√
√
√
√
Sleep Timer  
On Timer  
Off Timer  
: Off  
: Off  
: Off  
Move  
Enter  
Return  
Clock  
Press the ENTER button to select “Clock Mode”. Press the  
▲ or ▼ button to select “Manual”, then press the ENTER  
button.  
Clock Mode  
: Manual  
√
√
√
√
Clock Set  
Time Zone  
DST  
: No  
Move  
Enter  
Return  
Clock Set  
Set current date and time.  
Press the ▲ or ▼ button to select “Clock Set”, then press  
the ENTER button.  
Month  
Day  
--  
Year  
----  
…
--  
†
Hour  
--  
Minute am/pm  
--  
--  
Press the œ or √ button to move to “Month”, “Day”,  
“Year”, “Hour”, “Minute”, or “am/pm”.  
Set the clock you want by pressing the ▲ or ▼ button,  
then press the ENTER button.  
Move  
Adjust  
Return  
5
6
Press the MENU button to exit.  
Notes  
• The current time will appear every time you press the INFO button.  
• You can set the Month, Day, Year, Hour and Minute directly by pressing the number buttons on the  
remote control.  
96  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Option 2: Setting the Clock Automatically  
The Clock can be set automatically if you are receiving a digital signal.  
T V  
Setup  
Press the MENU button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
Press the ▲ or ▼ button to select “Setup”, then press  
1
: English  
the ENTER button.  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Press the ▲ or ▼ button to select “Time”, then press the  
Move  
Enter  
Time  
Return  
ENTER button.  
2
T V  
Press the ENTER button to select “Clock”.  
--  
/
--  
/
----  
/
-- :-- --  
Clock  
√
√
√
√
Sleep Timer  
On Timer  
Off Timer  
: Off  
: Off  
: Off  
Press the ENTER button to select “Clock Mode”.  
Press the ▲ or ▼ button to select “Auto”, then press  
the ENTER button.  
3
Move  
Enter  
Return  
T V  
Clock  
Clock Mode  
: Auto  
√
√
√
√
Clock Set  
Time Zone  
DST  
Press the ▲ or ▼ button to select “Time Zone”, then  
: No  
press the ENTER button.  
4
Press the ▲ or ▼ button to highlight the time zone for  
your local area (and to move the highlight to the  
appropriate time zone on the map of the United States),  
then press the enter button.  
Move  
Time Zone  
Enter  
Return  
Select the time zone in which you live.  
Atlantic  
Eastern  
Central  
Mountain  
Pacific  
Alaska  
Hawaii  
Press the ▲ or ▼ button to select “DST” (Daylight Saving  
Time), then press the ENTER button.  
Press the ▲ or ▼ button to select “Yes” or “No”, then  
press the ENTER button.  
5
Move  
Enter  
Return  
T V  
Clock  
Press the MENU button to exit.  
Clock Mode  
Clock Set  
Time Zone  
DST  
: Auto  
6
: Yes  
No  
Note  
• Depending on the broadcast station and signal,  
the auto time may not be set correctly. If this occurs,  
set the time manually.  
Move  
Enter  
Return  
97  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the On/Off Timer  
T V  
Setup  
Press the MENU button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
Press the ▲ or ▼ button to select “Setup”, then press  
1
2
: English  
the ENTER button.  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Time  
Return  
T V  
T V  
T V  
Press the ▲ or ▼ button to select “Time”, then press the  
1/  
1/  
2005  
/
12 : 00 am  
ENTER button.  
Clock  
√
√
√
√
Press the ▲ or ▼ button to select “On Timer”, then  
press the ENTER button.  
Press the ▲ or ▼ button to adjust “Hour”, then press  
the √ button to move to the next step.  
Set other items using the same method as above.  
Sleep Timer  
On Timer  
Off Timer  
: Off  
: Off  
: Off  
Move  
Enter  
Return  
To activate “On Timer” with the setting entered, set  
Activation to “Yes” by pressing … or † button.  
On Timer  
Set on timer.  
Minute am/pm  
am  
Volume Activation  
Hour  
Antenna  
…
When finished, press the MENU button to return.  
12  
00  
Air  
†
Channel  
• The current time will appear every time you press  
the INFO button.  
• You can set the hour, minute, channel and volume  
directly by pressing the number buttons on the  
remote control.  
3
10  
No  
Return  
Move  
Adjust  
Off Timer  
Set off timer.  
Press the ▲ or ▼ button to select “Off Timer”, then press  
the ENTER button.  
Press the ▲ or ▼ button to adjust “Hour”, then press  
the √ button to move to the next step.  
Set other items using the same method as above.  
3
Hour Minute am/pm Activation  
…
am  
No  
12  
00  
†
To activate “Off Timer” with the setting entered, set  
Activation to “Yes” by pressing … or † button.  
Move  
Adjust  
Return  
When finished, press the ENTER button.  
Press the MENU button to exit.  
4
Note  
• Auto Power Off  
When you set the timer “On”, the television will eventually turn off, if no controls are operated for  
3 hours after the TV was turned on by the timer.  
This function is only available in timer “On” mode and prevents overheating or leakage, which  
may occur if a TV is on for too long (when you are on vacation, for example).  
98  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Sleep Timer  
The sleep timer automatically shuts off the TV after a preset time (from 30 to 180 minutes).  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
3
4
5
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Time  
Return  
Press the ▲ or ▼ button to select “Time”, then press the  
ENTER button.  
--  
/
--  
/
----  
/
-- -- --  
:
Clock  
√
√
√
√
Press the ▲ or ▼ button to select “Sleep Timer”, then  
press the ENTER button.  
Sleep Timer  
On Timer  
Off Timer  
: Off  
: Off  
: Off  
Move  
Enter  
Return  
Return  
Return  
Sleep Timer  
Set sleep timer.  
Press the ▲ or ▼ button to adjust “Minute”.  
• Setting the Timer sets the Activation to “Yes”  
automatically.  
Minute  
Activation  
Yes  
…
30  
†
Move  
Adjust  
Sleep Timer  
To cancel the set sleep timer:  
Set sleep timer.  
Press the √ button to select “Activation”.  
Press the ▲ or ▼ button to select “No”, then press  
the ENTER button.  
Minute  
Activation  
…
---  
No  
†
Move  
Adjust  
Press the MENU button to exit.  
99  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Function Description  
Selecting a Menu Language...................................................102  
Digital Noise Reduction .........................................................103  
Selecting the Film Mode.........................................................104  
Setting the Blue Screen ..........................................................105  
Using the Color Weakness Enhancement Option ......................106  
Viewing Closed Captions (On-Screen Text Messages) - Analog...107  
Viewing Closed Captions (On-Screen Text Messages) - Digital....108  
Menu Transparency Level.......................................................110  
Using the Energy Saving feature .............................................111  
Preventing Screen Burn-in.......................................................112  
Reducing the Effects of Screen Burn.........................................113  
Setting the Function Help .......................................................114  
Using the V-Chip (for USA).....................................................115  
Using the V-Chip (for Canada)................................................121  
Electronic Program Guide ......................................................129  
Remind List...........................................................................133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting a Menu Language  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
2
3
4
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
T V  
Setup  
Press the ▲ or ▼ button to select “Language”, then press  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
the ENTER button.  
: English  
Spanish  
French  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Configuración  
Return  
T V  
Press the ▲ or ▼ button to select the appropriate  
language: “English”, “Spanish”, or “French”.  
Press the ENTER button.  
Plug&Play  
Idioma  
Tiempo  
V-Chip  
Subtítulo  
Transpar. del menú  
√
: Español  
√
√
√
√
√
: Medio  
†
Más  
Mover  
Ingresar  
Regresar  
Press the MENU button to exit.  
102  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Digital Noise Reduction  
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction  
feature to help reduce any static and ghosting that may appear on the screen.  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
Picture  
: Dynamic  
Press the ▲ or ▼ button to select “Digital NR”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: 16:9  
: Off  
On  
:
: Off  
†
More  
Move  
Enter  
Return  
Picture  
: Dynamic  
Press the ▲ or ▼ button to select “On” or “Off”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: 16:9  
: Off  
On  
:
: Off  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
4
Note  
• The Digital NR function is available in all modes except PC.  
103  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Selecting the Film Mode  
On: Automatically senses and processes film signals from all sources and adjusts the picture for  
optimum quality.  
Off: Switches off the Film mode.  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
Picture  
: Dynamic  
Press the ▲ or ▼ button to select “Film Mode”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: 16:9  
: On  
: Off  
:
Off  
On  
†
More  
Move  
Enter  
Return  
Picture  
Press the ▲ or ▼ button to select “On” or “Off”, then  
press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
: Dynamic  
: 16:9  
: On  
: Off  
:
Off  
†
On  
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
4
Note  
• Film mode is supported in TV, VIDEO, S-VIDEO, and COMPONENT 480i.  
104  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Blue Screen  
If no signal is being received or the signal is very weak, a blue screen automatically replaces  
the noisy picture background. If you wish to continue viewing the poor picture, you must set the  
“Blue Screen“ mode to “Off“.  
T V  
T V  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
“Picture”, then press the ENTER button.  
1
2
3
4
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Picture  
Return  
Return  
Return  
Press the ▲ or ▼ button to select “Blue Screen”, then  
press the ENTER button.  
…
More  
Blue Screen  
Color Weakness  
PIP  
:
Off  
:
On  
Move  
Enter  
Picture  
Press the ▲ or ▼ button to select “On” or “Off”, then  
press the ENTER button.  
…
More  
Blue Screen  
Color Weakness  
PIP  
:
Off  
:
On  
Blue Screen is displayed when there is no signal from an external  
device in the External Mode, regardless of the Blue Screen Setting.  
➤
➤
Move  
Enter  
Press the MENU button to exit.  
105  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Color Weakness  
Enhancement Option  
This option adjusts the Red, Blue or Green color to enhance the image according to the user's  
particular color weakness.  
T V  
Picture  
: Dynamic  
Press the MENU button. Press the ▲ or ▼ button to select  
“Picture”, then press the ENTER button.  
Mode  
Size  
Digital NR  
DNIe Demo  
My Color Control  
Film Mode  
√
√
√
√
√
√
1
2
3
: 16:9  
: On  
: Off  
: Off  
†
More  
Move  
Enter  
Return  
T V  
Color Weakness  
Color Weakness : Off  
Red  
Green  
Blue  
Press the ▲ or ▼ button to select “Color Weakness”,  
√
then press the ENTER button.  
0
0
0
Enter  
Color Weakness  
Return  
T V  
Press the ENTER button. Press the ▲ or ▼ button to select  
“On”, then press the ENTER button.  
You will also see the items “Red“, “Green“, and  
“Blue“.  
Color Weakness  
Red  
Green  
Blue  
: On  
√
0
0
0
• Pressing the ▲ or ▼ button will alternate between  
“On” and “Off”.  
Move  
Enter  
Return  
Color Weakness  
Press the ▲ or ▼ button to select the item you wish to  
change, then press the ENTER button.  
Press the œ or √ button to change the value of  
the item, then press the ENTER button.  
Red  
Move  
0
4
5
Adjust  
Return  
Press the ▲ or ▼ button to select another item.  
Press the MENU button to exit.  
106  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Closed Captions (On-Screen  
Text Messages) - Analog  
The Analog Caption function operates in either analog RF channel mode or external signal mode.  
T V  
T V  
T V  
T V  
Setup  
Press the Menu button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
: English  
Quick way to select Caption: Simply press the “CAPTION” button  
under the cover of the remote control.  
➤
➤
Menu Transparency  
: Medium  
†
Press the ▲ or ▼ button to select “Caption”, then press  
the ENTER button.  
More  
Move  
Enter  
Return  
2
3
Caption  
: Off  
: Default  
Press the ENTER button to select “Caption”.  
Press the ▲ or ▼ button to select “On”, then press the  
ENTER button.  
Caption  
Caption Mode  
Caption Options  
√
√
√
Press the ▲ or ▼ button to select “Caption Mode”, then  
press the ENTER button.  
Press the ▲ or ▼ button to select submenu  
(CC1~CC4 or Text1~Text4) you want, the press  
the ENTER button.  
4
Enter  
Return  
Caption  
: On  
: Default  
Caption  
Caption Mode  
Caption Options  
√
√
√
• The default is “CC1”.  
CC1 : The Primary Synchronous Caption Service.  
These are captions in the primary language  
that must be in sync with the sound, preferably  
matched to a specific frame.  
CC2 : The Special Non-Synchronous Use Captions.  
This channel carries data that is intended to  
augment information carried in the program.  
CC3 : Secondary Synchronous Caption Service.  
Alternate program-related caption data,  
typically second language captions.  
CC4 : Special Non-Synchronous Use Captions.  
Similar to CC2.  
Text1 : First Text Service. This may be various  
non-program related data.  
Text2 : Second Text Service. Additional data,  
usually not program related.  
Text3/Text4 : Third and Fourth Text Services. These  
data channels should be used only if  
Text1 and Text2 data bandwidths not  
sufficient.  
Move  
Enter  
Caption  
Return  
Default  
:
:
Caption  
Caption Mode  
Caption Options  
CC1  
CC2  
CC3  
CC4  
Text 1  
Text 2  
Text 3  
Text 4  
Move  
Enter  
Return  
Press the MENU button to exit.  
5
Notes  
• The Caption feature doesn’t work in COMPONENT, PC, HDMI(DVI) modes.  
• The availability of captions depends on the program being broadcast.  
107  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Closed Captions (On-Screen  
Text Messages) - Digital  
The Digital Captions function operates on digital channels.  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button.  
Press the ▲ or ▼ button to select “Setup”, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
1
2
3
4
5
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Caption  
: Off  
: Default  
Press the ▲ or ▼ button to select “Caption”, then press  
the ENTER button.  
Caption  
Caption Mode  
Caption Options  
√
√
√
Enter  
Return  
Caption  
: On  
: Default  
Press the ENTER button to select “Caption”.  
Press the ▲ or ▼ button to select “On”, then press  
the ENTER button.  
Caption  
Caption Mode  
Caption Options  
√
√
√
Move  
Enter  
Return  
Caption  
:
Press the ▲ or ▼ button to select “Caption Mode”, then  
press the ENTER button.  
Press the ▲ or ▼ button to select submenu  
(Service1~Service6, CC1~CC4 or Text1~Text4) you  
want, then press the ENTER button.  
Caption  
Caption Mode  
Caption Options  
Default  
:
Service1  
Service2  
Service3  
Service4  
Service5  
Service6  
CC1  
†
Move  
Enter  
Return  
T V  
Caption  
Press the ▲ or ▼ button to select “Caption Options”,  
then press the ENTER button.  
Caption  
Caption Mode  
Caption Options  
: On  
: Service1  
√
√
√
Notes  
• “Caption Options” are available only when  
“Service1~Service6” can be selected in “Caption Mode”.  
Move  
Enter  
Return  
• Service1~6 in digital caption mode may not be  
available according to the broadcasting type.  
108  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T V  
Caption Options  
: Default  
Press the ▲ or ▼ button to select “Size”, then press the  
Size  
Font Style  
√
√
√
√
√
√
√
ENTER button.  
6
7
: Default  
: Default  
: Default  
: Default  
: Default  
Foreground Color  
Background Color  
Foreground Opacity  
Background Opacity  
Return to Default  
Press the ▲ or ▼ button to select the desired Caption  
option, then press the ENTER button.  
Press the ▲ or ▼ button to select the desired  
sub-menu options(see options below), then press ENTER.  
Move  
Enter  
Return  
Notes  
• The availability of captions depends on the  
program being broadcast.  
• “Default” means to return to the original caption  
options set by the broadcaster.  
Press the MENU button to exit.  
• Size  
This option consists of “Default”, “Small”, “Standard”, and “Large”. The default is “Standard”.  
• Font Style  
This option consists of “Default”, “Style 0 ~ Style 7”. You can change the font you want.  
The default is “Style 0”.  
• Foreground Color  
This option consists of “Default”, “White”, “Black”, “Red”, “Green”, “Blue”, “Yellow”, “Magenta”,  
and “Cyan”. You can change the color of the letter. The default is “White”.  
• Background Color  
This option consists of “Default”, “White”, “Black”, “Red”, “Green”, “Blue”, “Yellow”, “Magenta”,  
and “Cyan”. You can change the background color of the caption. The default is “Black”.  
• Foreground Opacity  
This option consists of “Default”, “Transparent”, “Translucent”, “Solid”, and “Flashing”.  
You can change the opacity of the letter.  
• Background Opacity  
This option consists of “Default”, “Transparent”, “Translucent”, “Solid”, and “Flashing”.  
You can change the background opacity of the caption.  
• Return to Default  
This option sets each of “Size”, “Font Style”, “Foreground Color”, “Background color”,  
“Foreground Opacity”, and “Background Opacity” to its default.  
Alternate method:  
Press the CAPTION button on the remote control repeatedly to  
select “On” or “Off”.  
Caption : On  
109  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Transparency Level  
Adjusts the transparency of the menu screen.  
T V  
Setup  
Press the MENU button.  
Press the ▲ or ▼ button to select “Setup”, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
2
3
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
T V  
Setup  
Press the ▲ or ▼ button to select “Menu Transparency”,  
then press the ENTER button.  
Press the ▲ or ▼ button to select level, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
: English  
High  
Medium  
Low  
Opaque  
:
Menu Transparency  
†
More  
Move  
Enter  
Return  
Press the MENU button to exit.  
110  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Energy Saving Feature  
This feature adjusts the screen brightness automatically depending on the surrounding lighting  
conditions.  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
3
: English  
Quick way to select Energy Saving: Simply press the “E.SAVING”  
button under the cover of the remote control.  
➤
➤
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Setup  
Press the ▲ or ▼ button to select “Energy Saving”, then  
press the ENTER button.  
…
More  
Energy Saving  
: Standard  
Super Saving  
Screen Burn Protection  
PC  
Function Help  
: Off  
Move  
Enter  
Setup  
Return  
Press the ▲ or ▼ button to select submenu (Standard or  
Super Saving) you want, then press the ENTER button.  
…
More  
Standard  
Energy Saving  
Screen Burn Protection  
PC  
:
Super Saving  
• Standard  
: Operates in standard mode  
regardless of the surrounding  
illumination.  
Function Help  
: Off  
• Super Saving : Enters maximum power saving  
mode regardless of the surrounding  
illumination.  
Move  
Enter  
Return  
Press the MENU button to exit.  
4
111  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preventing Screen Burn-in  
To reduce the possibility of screen burn, this unit is equipped with screen burn prevention  
technology. This technology enables you to set picture movement up/down (Vertical Line) and side  
to side (Horizontal Dot). The Time setting allows you to program the time between movement of the  
picture in minutes.  
T V  
T V  
T V  
Setup  
Press the MENU button.  
Press the ▲ or ▼ button to select “Setup”, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
1
2
3
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Screen Burn Protection  
Press the ▲ or ▼ button to select “Screen Burn  
Protection”, then press the ENTER button.  
Pixel Shift  
All White  
Signal Pattern  
√
√
√
Move  
Enter  
Return  
Pixel Shift  
Press the ENTER button to select “Pixel Shift”, then press  
the ENTER button.  
Pixel Shift  
Horizontal Dot  
Vertical Line  
Time  
:
Off  
:
: 2  
: 2  
On  
• Pressing the ▲ or ▼ button will alternate between  
“On” and “Off”.  
You will also see the items “Horizontal Dot”,  
“Vertical Line” and “Time”.  
Move  
Enter  
Return  
• Pixel Shift: Using this function, you can minutely  
move pixels on the PDP in horizontal or  
vertical direction to prevent after image  
on the screen.  
T V  
Pixel Shift  
: On  
: 0  
Press the ▲ or ▼ button to select the item you wish to  
change, then press the ENTER button.  
Press the ▲ or ▼ button to change the value of the item,  
then press the ENTER button.  
Pixel Shift  
Horizontal Dot  
Vertical Line  
Time  
4
5
1
:
2
:
3
4
• Optimum condition for pixel shift;  
Horizontal Dot  
Vertical Line  
Time(min)  
2
2
2
Move  
Enter  
Return  
Press the MENU button to exit.  
112  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reducing the Effects of Screen Burn  
If screen burn has occurred, you can select a white screen or signal pattern (rolling screen) to help  
remove screen burn artifacts.  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button.  
Press the ▲ or ▼ button to select “Setup”, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
1
2
3
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Screen Burn Protection  
Press the ▲ or ▼ button to select “Screen Burn  
Protection”, then press the ENTER button.  
Pixel Shift  
All White  
Signal Pattern  
√
√
√
Move  
Enter  
Return  
Screen Burn Protection  
Press the ▲ or ▼ button to select “All White” or “Signal  
Pattern”, then press the ENTER button.  
Pixel Shift  
All White  
Signal Pattern  
√
√
√
• All White: This function removes after-images on the  
screen by changing the color of pixels to  
white. Use this function when there are  
remaining after-images or symbols on the  
screen especially when you displayed a  
still image on the screen for a long time.  
• Signal Pattern: This function removes after images on  
the screen by moving all the pixels on  
the PDP according to a pattern. Use  
Move  
Enter  
Return  
Screen Burn Protection  
Pixel Shift  
All White  
Signal Pattern  
√
√
√
this function when there are remaining  
after-images or symbols on the screen  
especially when you displayed a still  
image on the screen for a long time.  
Move  
Enter  
Return  
Press the MENU button to exit.  
4
Notes  
• To remove after-images on the screen, use either the “All White” or “Signal Pattern” function.  
Although both functions remove after-images on the screen, “Signal Pattern” is more effective.  
• The after-image removal function has to be executed for a long time (approximately 1 hour) to  
effectively remove after-images on the screen. If the after-image is not removed after performing  
the function, repeat the function again.  
113  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Function Help  
Displays help on the menu functions.  
T V  
T V  
T V  
Setup  
Press the MENU button.  
Press the ▲ or ▼ button to select “Setup”, then press  
the ENTER button.  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
1
2
3
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Setup  
Press the ▲ or ▼ button to select “Function Help”, then  
press the ENTER button.  
…
More  
Energy Saving  
: Standard  
Screen Burn Protection  
PC  
Function Help  
:
Off  
On  
Move  
Enter  
Setup  
Return  
Press the ▼ button to select “On”, then press the ENTER  
button.  
…
More  
Energy Saving  
Screen Burn Protection  
PC  
: Standard  
Function Help  
:
Off  
On  
Move  
Enter  
Return  
Switches the Function Help on.  
Press the MENU button to exit.  
4
114  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the V-Chip (for USA)  
The V-Chip feature automatically locks out programs that are deemed inappropriate for children.  
The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or  
changed.  
Notes :  
●
When the V-chip feature is activated, the PIP features do not function.  
The V-Chip does not work if the input is DTV (HD or SD).  
V-Chip function is not available in HDMI or component mode.  
●
●
Setting Up Your Personal ID Number (PIN)  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
T V  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
2
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Enter PIN  
*
*
*
*
Note  
•
The default PIN number of a new TV set is “0-0-0-0”.  
0~9 Enter PIN  
Change PIN  
Enter New PIN  
Return  
T V  
The “V-Chip” screen will appear. Press the ▲ or ▼  
button to select “Change PIN”, then press the ENTER  
button.  
3
4
Confirm New PIN  
0~9 Enter PIN  
Return  
The Change PIN screen will appear.  
Choose any 4 digits for your PIN and enter them.  
As soon as the 4 digits are entered, the “Confirm  
new PIN” screen appears. Re-enter the same 4 digits.  
When the Confirm screen disappears, your PIN has  
been memorized.  
Press the MENU button to exit.  
5
Note  
If you forget the PIN, press the remote-control buttons in the following sequence, which resets the  
•
pin to 0-0-0-0 : Power Off. ➔ Mute ➔ 8 ➔ 2 ➔ 4 ➔ Power On.  
115  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Enable/Disable the V-Chip  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Return  
Return  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press the  
ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
2
Enter PIN  
*
*
*
*
0~9 Enter PIN  
V-Chip  
The “V-Chip” screen will appear. To enable the V-Chip  
feature, press the ENTER button so that the “V-Chip Lock”  
field is “On”. (Pressing the ▲ or ▼ button will alternate  
between “On” and “Off”.)  
Press the ENTER button.  
Off  
V-Chip Lock  
:
On  
3
TV Parental Guidelines  
MPAA Rating  
Canadian English  
Canadian French  
Change PIN  
Move  
Enter  
Press the MENU button to exit.  
4
116  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using the “TV Parental Guidelines”  
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.)  
Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
3
4
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Enter PIN  
*
*
*
*
0~9 Enter PIN  
Return  
TV Parental Guidelines  
The “V-Chip” screen will appear. Press the ▲ or ▼  
button to select “TV Parental Guidelines”, then press  
the ENTER button.  
Allow All  
Block All  
Move  
Enter  
Return  
The “TV Parental Guidelines” screen will appear.  
Press the ▲ or ▼ button to select one of the six ages  
based categories:  
TV-Y  
TV-Y7  
Young children  
Children 7 and over  
TV-G  
General audience  
Parental guidance  
Viewers 14 and over  
Mature audience  
TV-PG  
TV-14  
TV-MA  
Note  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T V  
TV Parental Guidelines  
At this point, one of the TV-Ratings is selected.  
Press the ENTER button. Depending on your existing  
Allow All  
Block All  
5
setup, a symbol  
will be selected.  
= Blocked)  
(Blank = Unblocked,  
While “ ” is selected, press the ENTER button to  
block or unblock the category.  
To select a different TV-Rating, press the ▲ or ▼  
button and then repeat the process.  
Move  
Enter  
Return  
Note 1: The TV-Y, TV-Y7, TV-G, TV-PG, TV-14 and TV-MA have additional options.  
See the next step to change any of the following sub-ratings:  
FV: Fantasy violence  
D: Sexually Suggestive Dialog  
L: Adult Language  
S: Sexual situation  
V: Violence  
Note 2: The V-Chip will automatically block certain categories that are “more restrictive”.  
For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked.  
Similarly, if you block the TV-G category, then all the categories in the “young adult” group will  
be blocked (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA). The sub-ratings (D, L, S, V) work  
together similarly. (See next section.)  
How to set the FV, D, L, S and V sub-ratings.  
First, select one of these TV-Ratings: TV-Y, TV-Y7, TV-G, TV-PG, TV-14, or TV-MA (See Step 4,  
on previous page), and press the √ button.  
6
7
A symbol “ ” will be displayed for each sub-rating.  
While “ ” is selected, press the ENTER button to go to a sub rating.  
Press ENTER to block the sub rating. To select a different TV-Rating, press the ▲ or ▼ button  
and then repeat the process.  
Note: The V-chip will automatically block certain categories that are “More restrictive”.  
For example, if you block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA  
will automatically be blocked.  
Press the MENU button to clear all the screens. (Or proceed to the next section, and set up  
additional restrictions based on the MPAA codes.)  
Notes  
• These categories consist of two separate groups: TV-Y and TV-Y7 (young children through  
age 7), and TV-G through TV-MA (everybody else).  
The restrictions for these two groups work independently: If a household includes very young  
children as well as young adults, the TV guidelines must be set up separately for each age group.  
(See next step.)  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
118  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X, NR  
The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main  
application is for movies. When the V-Chip lock is on, the TV will automatically block any programs  
that are coded with objectionable ratings (either MPAA or TV-Ratings).  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
: English  
Menu Transparency  
: Medium  
†
More  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Move  
Enter  
Return  
V-Chip  
Enter PIN  
*
*
*
*
The “V-Chip” screen will appear.  
Press the ▲ or ▼ button to select “MPAA Rating”, then  
press the ENTER button.  
3
4
0~9 Enter PIN  
Return  
MPAA Rating  
Allow All  
Block All  
The “MPAA Rating” screen will appear.  
Repeatedly press the ▲ or ▼ button to select a particular  
MPAA category.  
Pressing the ▲ or ▼ button will cycle through the MPAA  
categories:  
G
General audience (no restrictions).  
Parental guidance suggested.  
Move  
Enter  
Return  
PG  
MPAA Rating  
PG-13 PG-13 (Parents strongly cautioned).  
R (Restricted. Children under 17 should be accompanied by an adult).  
NC-17 No children under age 17.  
Allow All  
Block All  
R
X
X (Adults only).  
Not rated.  
NR  
Move  
Enter  
Return  
While a particular category is selected, press the ENTER  
button to activate it.  
A selected symbol “ ” will be displayed.  
Press the ENTER button to block or unblock the category.  
Notes  
•
The V-Chip will automatically block any category that is “more restrictive”. For example, if  
you block the “PG-13” category, then “R”, “NC-17” and “X” will automatically be blocked also.  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
119  
How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”)  
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the  
following message will appear:  
Channel Is Locked by  
Enter your PIN number.  
TV-PG[ S ]  
1
Use the NUMBER buttons to enter your  
pin number to unlock all channels.  
Press EXIT to clear PIN.  
Press MENU for main menu.  
Channel Is Locked by  
TV-PG[ L ]  
Use the NUMBER buttons to enter your  
pin number to unlock all channels.  
Press EXIT to clear PIN.  
Press MENU for main menu.  
To resume normal viewing, tune to a different channel using CH  
or CH  
button.  
Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out  
all the channels. In this case, use the V-Chip function for an “emergency escape”:  
Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.  
1
Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button.  
2
Enter your PIN number then press the ENTER, and press the ▲ or ▼ button to temporarily disable  
the V-Chip Lock.  
3
120  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the V-Chip (for Canada)  
The V-Chip feature automatically locks out programs that are deemed inappropriate for children.  
The user must enter a PIN (personal ID number) before any of the V-Chip restrictions are set up or  
changed.  
Notes :  
●
When the V-chip feature is activated, the PIP features do not function.  
The V-Chip does not work if the input is DTV (HD or SD).  
V-Chip function is not available in HDMI or component mode.  
●
●
Setting Up Your Personal ID Number (PIN)  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
“Setup”, then press the ENTER button.  
Plug & Play  
Language  
Time  
√
√
√
√
√
√
1
: English  
V-Chip  
Caption  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
T V  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
2
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Enter PIN  
*
*
*
*
Note  
•
The default PIN number of a new TV set is “0-0-0-0”.  
0~9 Enter PIN  
Change PIN  
Enter New PIN  
Return  
T V  
The “V-Chip” screen will appear. Press the ▲ or ▼  
button to select “Change PIN”, then press the ENTER  
button.  
3
4
Confirm New PIN  
0~9 Enter PIN  
Return  
The Change PIN screen will appear.  
Choose any 4 digits for your PIN and enter them.  
As soon as the 4 digits are entered, the “Confirm  
new PIN” screen appears. Re-enter the same 4 digits.  
When the Confirm screen disappears, your PIN has  
been memorized.  
Press the MENU button to exit.  
5
Note  
If you forget the PIN, press the remote-control buttons in the following sequence, which resets the  
•
pin to 0-0-0-0 : Power Off. ➔ Mute ➔ 8 ➔ 2 ➔ 4 ➔ Power On.  
121  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Enable/Disable the V-Chip  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
Return  
Return  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press the  
ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
2
Enter PIN  
*
*
*
*
0~9 Enter PIN  
V-Chip  
The “V-Chip” screen will appear. To enable the V-Chip  
feature, press the ENTER button so that the “V-Chip Lock”  
field is “On”. (Pressing the ▲ or ▼ button will alternate  
between “On” and “Off”.)  
Press the ENTER button.  
Off  
V-Chip Lock  
:
On  
3
TV Parental Guidelines  
MPAA Rating  
Canadian English  
Canadian French  
Change PIN  
Move  
Enter  
Press the MENU button to exit.  
4
122  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using the “TV Parental Guidelines”  
First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.)  
Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
3
4
: English  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
V-Chip  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Enter PIN  
*
*
*
*
0~9 Enter PIN  
Return  
TV Parental Guidelines  
The “V-Chip” screen will appear. Press the ▲ or ▼  
button to select “TV Parental Guidelines”, then press  
the ENTER button.  
Allow All  
Block All  
Move  
Enter  
Return  
The “TV Parental Guidelines” screen will appear.  
Press the ▲ or ▼ button to select one of the six ages  
based categories:  
TV-Y  
TV-Y7  
Young children  
Children 7 and over  
TV-G  
General audience  
Parental guidance  
Viewers 14 and over  
Mature audience  
TV-PG  
TV-14  
TV-MA  
Note  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
123  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T V  
TV Parental Guidelines  
At this point, one of the TV-Ratings is selected.  
Press the ENTER button. Depending on your existing  
Allow All  
Block All  
5
setup, a symbol  
will be selected.  
= Blocked)  
(Blank = Unblocked,  
While “ ” is selected, press the ENTER button to  
block or unblock the category.  
To select a different TV-Rating, press the ▲ or ▼  
button and then repeat the process.  
Move  
Enter  
Return  
Note 1: The TV-Y, TV-Y7, TV-G, TV-PG, TV-14 and TV-MA have additional options.  
See the next step to change any of the following sub-ratings:  
FV: Fantasy violence  
D: Sexually Suggestive Dialog  
L: Adult Language  
S: Sexual situation  
V: Violence  
Note 2: The V-Chip will automatically block certain categories that are “more restrictive”.  
For example, if you block “TV-Y” category, then TV-Y7 will automatically be blocked.  
Similarly, if you block the TV-G category, then all the categories in the “young adult” group will  
be blocked (TV-Y, TV-Y7, TV-G, TV-PG, TV-14, and TV-MA). The sub-ratings (D, L, S, V) work  
together similarly. (See next section.)  
How to set the FV, D, L, S and V sub-ratings.  
First, select one of these TV-Ratings: TV-Y, TV-Y7, TV-G, TV-PG, TV-14, or TV-MA (See Step 4,  
on previous page), and press the √ button.  
6
7
A symbol “ ” will be displayed for each sub-rating.  
While “ ” is selected, press the ENTER button to go to a sub rating.  
Press ENTER to block the sub rating. To select a different TV-Rating, press the ▲ or ▼ button  
and then repeat the process.  
Note: The V-chip will automatically block certain categories that are “More restrictive”.  
For example, if you block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA  
will automatically be blocked.  
Press the MENU button to clear all the screens. (Or proceed to the next section, and set up  
additional restrictions based on the MPAA codes.)  
Notes  
• These categories consist of two separate groups: TV-Y and TV-Y7 (young children through  
age 7), and TV-G through TV-MA (everybody else).  
The restrictions for these two groups work independently: If a household includes very young  
children as well as young adults, the TV guidelines must be set up separately for each age group.  
(See next step.)  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
124  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X, NR  
The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main  
application is for movies. When the V-Chip lock is on, the TV will automatically block any programs  
that are coded with objectionable ratings (either MPAA or TV-Ratings).  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
: English  
Menu Transparency  
: Medium  
†
More  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Move  
Enter  
Return  
V-Chip  
Enter PIN  
*
*
*
*
The “V-Chip” screen will appear.  
Press the ▲ or ▼ button to select “MPAA Rating”, then  
press the ENTER button.  
3
4
0~9 Enter PIN  
Return  
MPAA Rating  
Allow All  
Block All  
The “MPAA Rating” screen will appear.  
Repeatedly press the ▲ or ▼ button to select a particular  
MPAA category.  
Pressing the ▲ or ▼ button will cycle through the MPAA  
categories:  
G
General audience (no restrictions).  
Parental guidance suggested.  
Move  
Enter  
Return  
PG  
MPAA Rating  
PG-13 PG-13 (Parents strongly cautioned).  
R (Restricted. Children under 17 should be accompanied by an adult).  
NC-17 No children under age 17.  
Allow All  
Block All  
R
X
X (Adults only).  
Not rated.  
NR  
Move  
Enter  
Return  
While a particular category is selected, press the ENTER  
button to activate it.  
A selected symbol “ ” will be displayed.  
Press the ENTER button to block or unblock the category.  
Notes  
•
The V-Chip will automatically block any category that is “more restrictive”. For example, if  
you block the “PG-13” category, then “R”, “NC-17” and “X” will automatically be blocked also.  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
125  
How to Set up Restrictions using “Canadian English”: E, C, C8+, G, PG, 14+, 18+  
First, set up a personal identification number (PIN), and enable the V-Chip. (refer to page 122)  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
: English  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
V-Chip  
The “V-Chip” screen will appear. Press the ▲ or ▼ button to  
select “Canadian English”, then press the ENTER button.  
3
4
Enter PIN  
*
*
*
*
The “Canadian English” screen will appear.  
Repeatedly press the ▲ or ▼ button to select a particular  
Canadian English category..  
Pressing the ▲ or ▼ button will cycle through the  
Canadian English categories:  
0~9 Enter PIN  
Return  
Canadian English  
Allow All  
Block All  
E
Exempt programming includes…news, sports, documentaries  
and other information programming, talk shows, music videos,  
and variety programming.  
C
Programming intended for children under age 8  
C8+  
Programming generally considered acceptable for children 8  
years and over to watch on their own  
Move  
Enter  
Return  
G
General programming, suitable for all audiences  
Parental Guidance  
PG  
14+  
Canadian English  
Programming contains themes or content which may not be  
suitable for viewers under the age of 14  
Allow All  
Block All  
18+  
Adult Programming  
While a particular category is selected, press the  
ENTER button to activate it.  
A selected symbol “ ” will be displayed.  
Press the ▲ or ▼ button to select “ ”.  
Move  
Enter  
Return  
Press the MENU button to save the settings and to clear all  
screens.  
5
Notes  
•
The V-Chip will automatically block any category that is “more restrictive”. For example,  
if you block the “G” category, then “PG”, “14+” and “18+” will automatically be blocked also.  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
126  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Set up Restrictions using “Canadian French”: E, G, 8 ans +, 13 ans +, 16 ans +, 18 ans +  
First, set up a personal identification number (PIN), and enable the V-Chip. (refer to page 122)  
T V  
T V  
T V  
T V  
Setup  
Press the MENU button. Press the ▲ or ▼ button to select  
Plug & Play  
Language  
Time  
V-Chip  
Caption  
√
√
√
√
√
√
“Setup”, then press the ENTER button.  
1
2
: English  
Press the ▲ or ▼ button to select “V-Chip”, then press  
the ENTER button.  
The message “Enter PIN” will appear.  
Enter your 4 digit PIN number.  
Menu Transparency  
: Medium  
†
More  
Move  
Enter  
Return  
V-Chip  
The “V-Chip” screen will appear. Press the ▲ or ▼ button to  
select “Canadian French”, then press the ENTER button.  
3
4
Enter PIN  
*
*
*
*
The “Canadian French” screen will appear.  
Repeatedly press the ▲ or ▼ button to select a particular  
Canadian French category.  
Pressing the ▲ or ▼ button will cycle through the  
Canadian French categories:  
0~9 Enter PIN  
Return  
Canadian French  
Allow All  
Block All  
E
Exempt programming includes…news, sports, documentaries  
and other information programming, talk shows, music videos,  
and variety programming.  
G
General  
8 ans + 8+ General – Not recommended for young children  
13 ans + Programming may not be suitable for children under the age of 13  
16 ans + Programming is not suitable for children under the age of 16  
18 ans + Programming restricted to adults  
Move  
Enter  
Return  
Canadian French  
Allow All  
Block All  
While a particular category is selected, press the  
ENTER button to activate it.  
A selected symbol “ ” will be displayed.  
Press the ▲ or ▼ button to select “ ”.  
Move  
Enter  
Return  
Press the MENU button to save the settings and to clear all  
screens.  
5
Notes  
•
The V-Chip will automatically block any category that is “more restrictive”. For example,  
if you block the “8 ans+” category, then “13 ans+”, “16 ans+” and “18 ans+” will automatically  
be blocked also.  
•
Allow All  
Block All  
: Press to unlock all TV ratings.  
: Press to lock all TV ratings.  
127  
Download from Www.Somanuals.com. All Manuals Search And Download.  
How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”)  
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the  
following message will appear:  
Channel Is Locked by  
Enter your PIN number.  
TV-PG[ S ]  
1
Use the NUMBER buttons to enter your  
pin number to unlock all channels.  
Press EXIT to clear PIN.  
Press MENU for main menu.  
Channel Is Locked by  
TV-PG[ L ]  
Use the NUMBER buttons to enter your  
pin number to unlock all channels.  
Press EXIT to clear PIN.  
Press MENU for main menu.  
To resume normal viewing, tune to a different channel using CH  
or CH  
button.  
Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out  
all the channels. In this case, use the V-Chip function for an “emergency escape”:  
Press the MENU button. Press the ▲ or ▼ button to select “Setup”, then press the ENTER button.  
1
Press the ▲ or ▼ button to select “V-Chip”, then press the ENTER button.  
2
Enter your PIN number then press the ENTER, and press the ▲ or ▼ button to temporarily disable  
the V-Chip Lock.  
3
128  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Electronic Program Guide  
Your TV has an “Electronic Program Guide” to help you  
navigate through all the possible viewing options.  
The EPG supplies information, such as program lists,  
start and end times of all available channels.  
In addition, detailed information about the program is  
often available in the EPG. (The availability and the  
amount of program details will vary depending on the  
broadcaster.)  
I
H
A
B
C E  
D
F
G
Viewing the Electronic Program Guide  
A
B
C
Displays which channel is currently selected to show program information in the Channel Guide.  
Press to view detailed information for the selected digital program.  
Switches to the mini program guide. The mini guide shows the titles of the available programs of  
one channel. Press the Red button on the remote control. The set default guide is Mini Guide.  
D
E
Scrolls backwards quickly (2 hours). Press the Green button on the remote control.  
Displays titles and other details about upcoming programs of particular channels. Highlight the  
program and press the INFO button to see additional and detailed information. (The availability  
of additional details depends on the broadcaster.) Use the ▲/▼/œ/√ buttons to search  
information about another channel.  
F
Scrolls forward quickly (2 hours). Press the Yellow button on the remote control and repeatedly  
press the ENTER button the appropriate time is displayed.  
G
Exits from the Program Guide and returns to normal viewing mode. Press the Blue button on the  
remote control.  
H
I
Displays the program times (arranged in 1 hour time blocks).  
Displays the current time and date.  
Note  
• You can use the GUIDE button on the remote control to display the Electronic Program Guide.  
The EPG begins its list with the channel that is currently active.  
The EPG will only work when you are receiving digital channels.  
129  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Using the Electronic Program Guide  
T V  
T V  
T V  
Guide  
Press the MENU button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
√
√
√
√
Press the ▲ or ▼ button to select “Guide”, then  
1
press the ENTER button.  
: Mini Guide  
Move  
Enter  
Return  
Return  
Return  
Guide  
Press the ▲ or ▼ button to select “Default Guide”, then  
press the ENTER button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
2
: MiniGuide  
Full Guide  
Move  
Enter  
Guide  
Press the ▲ or ▼ button to select “Mini Guide” or “Full  
Guide”, then press the ENTER button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
3
• Mini Guide : Displays the guide for one channel.  
• Full Guide : Displays the guide for all channels.  
Mini Guide  
:
Full Guide  
Move  
Enter  
Press the MENU button to exit.  
4
130  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Information about a Single Channel  
T V  
Guide  
Press the MENU button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
√
√
√
√
Press the ▲ or ▼ button to select “Guide”, then  
1
press the ENTER button.  
: Mini Guide  
Move  
Enter  
Return  
Mini Guide  
Press the ENTER button to select “Mini Guide”.  
3
Press the ▲ or ▼ buttons to view information about  
2
one channel by time.  
Program 1  
5:00 pm  
7:30 pm Program 2  
8:00 pm Program 3  
9:30 pm Program 4  
You can switch between Full Guide mode and Mini  
Guide mode by pressing the Red button repeatedly.  
Program 5  
Program 6  
10:00 pm  
11:30 pm  
Select the program you want by pressing the ▲ or  
▼ buttons and press the INFO button on the remote  
control.  
4:30 pm Fri May 31  
INFO  
Watch  
Prog Info  
Full Guide  
Exit  
• ENTER button: Press to watch the current program  
or to add the program to remind list.  
• Red button : Press to switch to the program  
guide for all channels.  
Press again to switch to the program  
information for the selected channel.  
• Blue button : Press to exit.  
• INFO button : Press to view detailed information  
for the selected digital program.  
Press the Blue button or EXIT button to exit.  
3
Notes  
• You can also view information about a single channel by pressing the GUIDE button on the remote  
control. (The EPG should be pre-set in Mini Guide mode.)  
• Press the INFO button on the remote control to view the program information for the current channel.  
131  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Viewing Information about Channels  
Displays the program time and content for all channels.  
This function is available only when the program is digital.  
T V  
Guide  
Press the MENU button.  
Press the ▲ or ▼ button to select “Guide”, then  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
√
√
√
√
1
press the ENTER button.  
: Mini Guide  
Press the ▲ or ▼ button to select “Full Guide”, then press  
the ENTER button.  
2
Move  
Enter  
Return  
Press the Green button to activate “-2 Hours” and the  
Yellow button to activate “+2 Hours”.  
3
• INFO button : Displays detailed information for  
the selected digital program.  
• ▲/▼ button : Displays program information for  
each channel, based on the time.  
Select your desired program using  
the ▲/▼ button, and then press the  
INFO button to view the program  
information for the selected program.  
• Red button  
: Each press switches between program  
information for one channel and all  
channels.  
• Green button : Press to view the program information  
from two hours ago.  
• Yellow button : Press to view the program information  
for two hours from now.  
• Blue button  
: Press to exit.  
• ENTER button : Press to watch the current program  
or to add the program to remind list.  
You may now:  
• Jump to a channel directly :  
Use the ▲, ▼, œ, or √ button to highlight the program  
and press the ENTER button.  
4
• Obtain additional program details : Highlight the title of a program using the ▲, ▼, œ, or √  
buttons and press the INFO button.  
• Exit from the Program Guide and return to normal viewing mode :  
Press the Blue button or the EXIT button.  
Notes  
• The current time displayed on the program information is subject to the time information sent from  
the broadcasting station, so it may differ from the actual time.  
• Press the GUIDE button on the remote control to view the program information for all channels.  
However, this function is available only when the default program guide setting is set to “Full Guide”.  
132  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Remind List  
Viewing the Remind List  
If you have made a scheduled viewing list of programs you would like to see, the channel will be  
automatically switched to the scheduled program at the scheduled time even if you are watching  
another program.  
T V  
Guide  
Press the MENU button.  
Press the ▲ or ▼ button to select “Guide”, then  
press the ENTER button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
√
√
√
√
1
2
: Mini Guide  
Move  
Enter  
Return  
Mini Guide  
Press the ENTER button to select “Full Guide”.  
Press the ▲ or ▼ button to select programs you would  
like to see, then press the enter button.  
3
Program 1  
5:00 pm  
The symbol “✔” will be displayed.  
7:30 pm Program 2  
8:00 pm Program 3  
9:30 pm Program 4  
Each press of the enter button will switch between  
“Remind” and “Del Remind”(Del=Delete).  
Remind List  
Program 5  
Program 6  
10:00 pm  
11:30 pm  
Press the MENU button to exit.  
4:30 pm Fri May 31  
INFO  
Watch  
Prog Info  
3
Full Guide  
Exit  
Note  
• Up to 8 programs can be reminded.  
133  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To view the Remind List  
T V  
Guide  
Press the MENU button.  
Mini Guide  
Full Guide  
Remind List  
Default Guide  
√
√
√
√
Press the ▲ or ▼ button to select “Guide”, then  
1
press the ENTER button.  
: Mini Guide  
Move  
Enter  
Return  
T V  
Guide  
Press the ▲ or ▼ button to select “Remind List”, then  
press the ENTER button.  
Mini Guide  
Full Guide  
√
√
√
√
2
Remind List  
Default Guide  
: Mini Guide  
Move  
Enter  
Return  
To remove the scheduled programs  
T V  
Remind List  
Press the ▲ or ▼ button to select a program to be  
removed, then press the ENTER button.  
1
MON 1.17 1:56am-2:05am  
11-1 MBC MBC  
Cancel All  
To remove all programs, press the œ or √ button to  
select “Cancel All”, then press the ENTER button.  
MON 1.17 3:15am-3:28am  
11-1 MBC  
MON 1.17 3:28am-3:29am  
11-1 MBC  
Move  
Enter  
Return  
Press the MENU button to exit.  
2
134  
Download from Www.Somanuals.com. All Manuals Search And Download.  
P
L
A
S
M
A
D
I
S
P
L
A Y  
P A  
N
E
L
Appendix  
Troubleshooting..........................................................................136  
Care and Maintenance ..............................................................137  
Specifications ............................................................................138  
Dimensions................................................................................139  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If the TV seems to have a problem, first try this list of possible problems and solutions.  
If none of these troubleshooting tips apply, then call your nearest service center.  
Problem  
Possible Solution  
Poor picture.  
Check all wire connections.  
No picture or sound.  
Try another channel. Press the SOURCE button.  
Make sure the TV is plugged in.  
Check the antenna connections.  
Check that the Mute feature is Off.  
Poor sound quality.  
Try another channel. Adjust the volume.  
Press the “MODE” button to put your remote control in  
the “TV” mode.  
Your remote control does not  
operate the TV.  
Check the battery charge of the remote control.  
Check if the power plug is connected.  
The TV won’t turn on.  
Check to see that both the TV and the source are  
plugged in and turned on.  
There is no screen image.  
The image is too light or too dark.  
The image is too large or too small.  
Adjust the Brightness or Contrast settings.  
Adjust the Size settings.  
Digital broadcasting screen  
problem.  
Please check the digital signal strength and input  
antenna.  
Screen is black and power indicator  
light blinks steadily.  
On your computer check; Power, Signal Cable.  
The TV is using its power management system.  
Move the computer’s mouse or press any key on the  
keyboard.  
On your equipment check (STB, DVD, etc) ; Power,  
Signal Cable.  
The TV is using its power management system.  
Press the Source button on the panel or remote control.  
Turn the TV off and on.  
The visual qualities of digital  
channels vary.  
The visual qualities of digital channels may vary  
depending on the original production method (analog  
or digital).  
➔ Classification by the information displayed when  
switching channels.  
➔ If the original production method is digital: High  
visual quality program.  
➔ If the original production method is analog: The  
digital program displayed on the screen is originally  
an analog program which has been converted.  
The visual quality is of an SD grade.  
The HD caption that appears when switching channels  
or when pressing the Information button on the remote  
control means the selected channel is simply a digital  
channel. If the broadcasting station converts an  
analog signal into digital and transmits the signal,  
the visual quality may not be perfect.  
Although the TV caption shows HD,  
the visual quality is not satisfactory.  
(Applied to Set Top Box built-in model only.)  
136  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Care and Maintenance  
With proper care, your TV will give you many years of service.  
Please follow these guidelines to get the maximum performance from your TV.  
Identifying Problems  
•
•
•
•
Do not put the TV near extremely hot, cold, humid or dusty places.  
Do not put the TV near appliances that create magnetic fields.  
Keep the ventilation openings clear.  
Do not place the TV on a rough and slanted surface, such as cloth or paper.  
Liquids  
•
Do not place liquids near or on the TV.  
Cabinet  
•
•
•
Never open the cabinet or touch the parts inside.  
Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.  
Do not put heavy objects on top of the cabinet.  
Temperature  
•
If your TV is suddenly moved from a cold to a warm place, unplug the power cord for at least two  
hours so that moisture that may have formed inside the unit can dry completely.  
137  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Specifications  
Exterior design and product specifications are subject to change without prior notice to improve  
the performance of this product.  
HP-R4272C  
HP-R5072C  
Model  
41.7 (W) x 29.1 (H) x 3.88 (D) inches (Without Stand) 48.43 (W) x 32.52 (H) x 3.72 (D) inches (Without Stand)  
Dimensions Display  
41.7 (W) x 30.7 (H) x 13.4 (D) inches (With Stand)  
39.8 Kg / 87.74 lbs (Without Stand)  
44.5 Kg / 98.10 lbs (With Stand)  
48.43 (W) x 34.47 (H) x 13.18 (D) inches (With Stand)  
46.8Kg / 103.17 lbs (Without Stand)  
53.5Kg / 117.95 lbs (With Stand)  
Weight  
Voltage  
Display  
AC 110-120V~, 60Hz  
Power Consumption  
Number of Pixels  
Screen Size  
380 W  
1024 (H) x 768 (V)  
42 inches  
420 W  
1366 (H) x 768 (V)  
50 inches  
ANTENNA input  
ANT 1 - CABLE IN (Cable QAM)  
ANT 2 - AIR IN (ATSC)  
75Ω unbalanced  
VIDEO input  
AUDIO input  
AV1, AV2  
S-VIDEO1, S-VIDEO2  
COMPONENT1 - 480i/480p/720p/1080i  
COMPONENT2 - 480i/480p/720p/1080i  
PC  
HDMI (DVI Compatible)  
AV1, AV2  
S-VIDEO1, S-VIDEO2  
COMPONENT1 - 480i/480p/720p/1080i  
COMPONENT2 - 480i/480p/720p/1080i  
PC  
DVI  
Sound Output  
Audio Output  
AUDIO (L/R)  
OPTICAL (DIGITAL OUT)  
COAXIAL (DIGITAL OUT)  
15W + 15W (8Ω)  
Speaker Output  
138  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions (HP-R4272C)  
JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM  
139  
Download from Www.Somanuals.com. All Manuals Search And Download.  
140  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dimensions (HP-R5072C)  
JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM  
141  
Download from Www.Somanuals.com. All Manuals Search And Download.  
142  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memo  
143  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1-800-SAMSUNG (1-800-726-7864)  
Samsung Electronics America  
Service Division  
400 Valley Road, Suite 201  
Mount Arlington, NJ 07856  
www.samsung.com  
Samsung Electronics Canada Inc.  
Samsung Customer Care  
55 Standish Court  
Mississauga, Ontario  
L5R 4B2  
www.samsung.ca  
BN68-00825J-00  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Q See Security Camera QT426 618 User Guide
Rangemaster Ventilation Hood E64000 User Guide
Regency Stove C34 LP2 User Guide
Rosewill Computer Drive RX358 User Guide
Rowenta Hair Dryer PH570 User Guide
Samsung Blu ray Player BD F6900 F6909S User Guide
Samsung Camera Lens SVD 4300 User Guide
Samsung Home Theater System HT DB1750 User Guide
Sears Lawn Mower 91725271 User Guide
Sears Tent 30870002 User Guide