OPERATOR’S MANUAL
12 in. DIGITAL DRILL PRESS
DP121L
Your drill press has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETy RULES
ALWAyS WEAR SAFETy GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses, they are NOT safety glasses.
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
SECURE WORK. Use clamps or a vise to hold work when
practical, it is safer than using your hand and frees both
hands to operate the tool.
DO NOT OVERREACH. Keep proper footing and balance
READ ALL INSTRUCTIONS
at all times.
KNOW yOUR POWER TOOL. Read the operator’s
manual carefully. Learn the applications and limitations
as well as the specific potential hazards related to this
tool.
MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for better and safer performance. Follow
instructions for lubricating and changing accessories.
DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades, bits,
cutters, etc., all tools should be disconnected from power
source.
GUARD AGAINST ELECTRICAL SHOCK By
PREVENTING BODy CONTACT WITH GROUNDED
SURFACES. For example: pipes, radiators, ranges, re-
frigerator enclosures.
AVOID ACCIDENTAL STARTING. Be sure switch is off
KEEP GUARDS IN PLACE and in good working order.
when plugging in any tool.
REMOVE ADJUSTING KEyS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
USE RECOMMENDED ACCESSORIES. Consult the
operator’s manual for recommended accessories. The
use of improper accessories may result in injury.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents. DO NOT leave tools or pieces
of wood on the tool while it is in operation.
NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
DO NOT USE IN DANGEROUS ENVIRONMENTS. Do
not use power tools in damp or wet locations or expose
to rain. Keep the work area well lit.
CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged must
be properly repaired or replaced by an authorized service
center to avoid risk of personal injury.
KEEP CHILDREN AND VISITORS AWAy. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or exten-
sion cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks,
master switches, or by removing starter keys.
USE THE RIGHT DIRECTION OF FEED. Feed work into
a blade, cutter, or sanding spindle against the direction
or rotation of the blade, cutter, or sanding spindle only.
DON’T FORCE THE TOOL. It will do the job better and
safer at the feed rate for which it was designed.
USE THE RIGHT TOOL. Do not force the tool or attach-
NEVER LEAVE TOOL RUNNING UNATTENDED. TURN
THE POWER OFF. Don’t leave tool until it comes to a
complete stop.
ment to do a job for which it was not designed.
USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. Use only a cord
heavy enough to carry the current your product will draw.
An undersized cord will cause a drop in line voltage
resulting in loss of power and overheating. A wire gauge
size (A.W.G.) of at least 16 is recommended for an
extension cord 50 feet or less in length. If in doubt, use
the next heavier gauge. The smaller the gauge number,
the heavier the cord.
PROTECT yOUR LUNGS. Wear a face or dust mask if
the cutting operation is dusty.
PROTECT yOUR HEARING. Wear hearing protection
during extended periods of operation.
DO NOT ABUSE CORD. Never carry tool by the cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
DRESS PROPERLy. Do not wear loose clothing, gloves,
neckties, or jewelry that can get caught and draw you
into moving parts. Rubber gloves and nonskid footwear
are recommended when working outdoors. Also wear
protective hair covering to contain long hair.
USE OUTDOOR EXTENSION CORDS. When tool is
used outdoors, use only extension cords with approved
ground connection that are intended for use outdoors
and so marked.
STAy ALERT AND EXERCISE CONTROL. Watch what
you are doing and use common sense. Do not operate
tool when you are tired. Do not rush.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETy RULES
DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
KEEP TOOL DRy, CLEAN, AND FREE FROM OIL AND
ON AND OFF. Have defective switches replaced by an
authorized service center.
GREASE. Always use a clean cloth when cleaning. Never
use brake fluids, gasoline, petroleum-based products, or
any solvents to clean tool.
ALWAyS TURN SWITCH OFF before disconnecting it
to avoid accidental starting.
NEVER START A TOOL WHEN ANy ROTATING
COMPONENT IS IN CONTACT WITH THE
WORKPIECE.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal
sparking of the motor could ignite fumes.
DO NOT OPERATE A TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANy
MEDICATION.
INSPECT TOOL CORDS PERIODICALLy. If damaged,
have repaired by a qualified service technician at an
authorized service facility. The conductor with insulation
having an outer surface that is green with or without
yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal. Repair or replace a damaged or worn
cord immediately. Stay constantly aware of cord location
and keep it well away from the rotating blade.
WHEN SERVICING use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
USE ONLy RECOMMENDED ACCESSORIES listed in
this manual or addendums. Use of accessories that are
not listed may cause the risk of personal injury. Instruc-
tions for safe use of accessories are included with the
accessory.
INSPECT EXTENSION CORDS PERIODICALLy and
replace if damaged.
GROUND ALL TOOLS. If tool is equipped with three-
prong plug, it should be plugged into a three-hole elec-
trical receptacle.
USE ONLy CORRECT ELECTRICAL DEVICES: 3-wire
extension cords that have 3-prong grounding plugs and
3-pole receptacles that accept the tool’s plug.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFIC SAFETy RULES
KEEP BITS CLEAN AND SHARP. Sharp bits minimize
ALWAyS ENSURE THE LASER BEAM IS AIMED AT
A SURFACE WITHOUT REFLECTIVE PROPERTIES.
stalling. Dirty and dull bits may cause misalignment of
the material and possible operator injury.
Shiny reflective materials are not suitable for laser use.
KEEP HANDS AWAy FROM WORK AREA. Keep hands
away from the bit. Restrain any loose clothing, jewelry,
long hair, etc., that may become entangled in the bit.
NEVER PLACE yOUR FINGERS IN A POSITION
WHERE THEy COULD CONTACT THE DRILL or other
cutting tool if the workpiece should unexpectedly shift.
ALWAyS CLAMP WORKPIECE AND BRACE AGAINST
COLUMN TO PREVENT ROTATION. Never use your
hand to hold the object while drilling.
NEVER PERFORM ANy OPERATION by moving the
head or table with respect to one another. Do not turn the
motor switch ON or start any operation before checking
that the head and table support lock handle is clamped
tight to column and head and table support collars are
correctly positioned.
USE RECOMMENDED SPEED FOR DRILL ACCES-
SORy AND WORKPIECE MATERIAL.
BE SURE DRILL BIT OR CUTTING TOOL IS SECURELy
BEFORE ENGAGING THE POWER SWITCH, MAKE
SURE THE BELT GUARD IS DOWN AND THE CHUCK
IS INSTALLED PROPERLy.
LOCKED IN THE CHUCK.
BE SURE CHUCK KEy IS REMOVED from the chuck
before connecting to power source or turning power
ON.
LOCK THE MOTOR SWITCH OFF WHEN LEAVING
THE DRILL PRESS. Do not perform layout, assembly, or
set-up work on the table while the cutting tool is rotating,
switched on, or connected to a power source.
ADJUST THE TABLE OR DEPTH STOP TO AVOID
DRILLING INTO THE TABLE. Shut off the power, remove
the drill bit, and clean the table before leaving machine.
SAVE THESE INSTRUCTIONS. Refer to them frequently
and use to instruct other users. If you loan someone this
tool, loan them these instructions also.
AVOID DIRECT EyE EXPOSURE when using the laser
guide.
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals, work in a well ventilated area, and work with approved safety equipment, such as those dust masks
that are specially designed to filter out microscopic particles.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SyMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-
tion of these symbols will allow you to operate the tool better and safer.
SyMBOL
NAME
DESIGNATION/EXPLANATION
V
Volts
Voltage
Current
A
Hz
W
Amperes
Hertz
Watt
Frequency (cycles per second)
Power
min
Minutes
Time
Alternating Current
Type of current
Direct Current
Type or a characteristic of current
Rotational speed, at no load
n
No Load Speed
o
Class II Construction
Per Minute
Double-insulated construction
.../min
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to rain or use in damp locations.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Read The Operator’s Manual
Always wear safety goggles or safety glasses with side shields
and a full face shield when operating this product.
Eye Protection
Safety Alert
Precautions that involve your safety.
Failure to keep your hands away from the blade will result in
serious personal injury.
No Hands Symbol
To reduce the risk of injury or damage, avoid contact with
any hot surface.
Hot Surface
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SyMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this
product.
SyMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION:
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servic-
ing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe opera-
tion and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
EXTENSION CORDS
SPEED AND WIRING
Use only 3-wire extension cords that have 3-prong ground-
ing plugs and 3-pole receptacles that accept the tool’s plug.
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter’s Laboratories (UL) should be used.
The no-load speed of this tool is approximately 3,000 rpm.
This speed is not constant and decreases under a load
or with lower voltage. For voltage, the wiring in a shop
is as important as the motor’s horsepower rating. A line
intended only for lights cannot properly carry a power
tool motor. Wire that is heavy enough for a short distance
will be too light for a greater distance. A line that can
support one power tool may not be able to support two
or three tools.
GROUNDING INSTRUCTIONS
**Ampere rating (on tool faceplate)
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This tool is equipped with
an electric cord having an equipment-grounding conduc-
tor and a grounding plug. The plug must be plugged into a
matching outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
0-ꢀ.0
ꢀ.1-3.4
3.5-5.0
5.1-7.0
7.1-1ꢀ.0 1ꢀ.1-16.0
Cord Length
Wire Size (A.W.G.)
ꢀ5'
50'
16
16
16
16
16
16
16
16
14
16
14
1ꢀ
14
14
10
14
1ꢀ
—
100'
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improperconnectionoftheequipment-groundingconductor
can result in a risk of electric shock. The conductor with
insulation having an outer surface that is green with or with-
out yellow stripes is the equipment-grounding conductor. If
repair or replacement of the electric cord or plug is neces-
sary, do not connect the equipment-grounding conductor
to a live terminal.
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters “WA” on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires, and cut or worn insulation.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the tool is properly grounded.
WARNING:
Keep the extension cord clear of the working area.
Position the cord so that it will not get caught on lumber,
tools, or other obstructions while you are working with
a power tool. Failure to do so can result in serious per-
sonal injury.
Repair or replace a damaged or worn cord immediately.
This tool is intended for use on a circuit that has an outlet
like the one shown in figure 1. It also has a grounding pin
like the one shown.
WARNING:
Check extension cords before each use. If damaged re-
place immediately. Never use tool with a damaged cord
since touching the damaged area could cause electrical
shock resulting in serious injury.
ELECTRICAL CONNECTION
This tool is powered by a precision built electric motor. It
should be connected to a power supply that is 120 volts,
60Hz,AConly(normalhouseholdcurrent).Donotoperate
this tool on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If the
tool does not operate when plugged into an outlet, double
check the power supply.
GroundinG
120V Grounded outlet
Pin
Fig. 1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARy OF TERMS
Anti-Kickback Pawls (radial arm and table saws)
Non-Through Cuts
A device which, when properly installed and maintained,
is designed to stop the workpiece from being kicked back
toward the front of the saw during a ripping operation.
Any cutting operation where the blade does not extend
completely through the thickness of the workpiece.
Pilot Hole (drill presses)
Arbor
A small hole drilled in a workpiece that serves as a guide for
The shaft on which a blade or cutting tool is mounted.
drilling large holes accurately.
Bevel Cut
Push Blocks and Push Sticks
A cutting operation made with the blade at any angle other
than 90° to the table surface.
Devices used to feed the workpiece through the saw blade
during cutting operations. A push stick (not a push block)
should be used for narrow ripping operations. These aids
help keep the operator's hands well away from the blade.
Chamfer
A cut removing a wedge from a block so the end (or part of
the end) is angled rather than at 90°.
Resaw
A cutting operation to reduce the thickness of the workpiece
to make thinner pieces.
Compound Cut
A cross cut made with both a miter and a bevel angle.
Resin
Crosscut
A sticky, sap-based substance that has hardened.
A cutting or shaping operation made across the grain or the
width of the workpiece.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object in one
minute.
Cutter Head (planers and jointers)
A rotating piece of adjustable blades. The cutter head
removes material from the workpiece.
Ripping or Rip Cut
A cutting operation along the length of the workpiece.
Dado Cut
A non-through cut which produces a square-sided notch or
trough in the workpiece (requires a special blade).
Riving Knife (table saws)
Also known as a spreader or splitter. A metal piece, slightly
thinner than the saw blade, which helps keep the kerf open
and also helps to prevent kickback.
Featherboard
A device used to help control the workpiece by guiding
it securely against the table or fence during any ripping
operation.
Saw Blade Path
The area over, under, behind, or in front of the blade. As it
applies to the workpiece, that area which will be or has been
cut by the blade.
FPM or SPM
Feet per minute (or strokes per minute), used in reference
to blade movement.
Set
The distance that the tip of the saw blade tooth is bent (or
set) outward from the face of the blade.
Freehand
Performing a cut without the workpiece being guided by a
fence, miter gauge, or other aids.
Snipe (planers)
Depression made at either end of a workpiece by cutter
blades when the workpiece is not properly supported.
Gum
A sticky, sap-based residue from wood products.
Through Sawing
Heel
Any cutting operation where the blade extends completely
through the thickness of the workpiece.
Alignment of the blade to the fence.
Kerf
Throw-Back
The material removed by the blade in a through cut or the
The throwing back of a workpiece usually caused by the
workpiece being dropped into the blade or being placed
inadvertently in contact with the blade.
slot produced by the blade in a non-through or partial cut.
Kickback
A hazard that can occur when the blade binds or stalls,
Workpiece or Material
throwing the workpiece back toward operator.
The item on which the operation is being done.
Leading End
Worktable
The end of the workpiece pushed into the tool first.
Surface where the workpiece rests while performing a
cutting, drilling, planing, or sanding operation.
Miter Cut
A cutting operation made with the workpiece at any angle
to the blade other than 90°.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
PRODUCT SPECIFICATIONS
Chuck ........................................................................1/ꢀ in.
Input ............................... 1ꢀ0 Volt, 60Hz, AC Only, 5 Amps
Motor........................................................1/3 HP Induction
No Load Speed ......................................... 500–3,000 RPM
Swing.......................................................................... 1ꢀ in.
Spindle Travel............................................................... 3 in.
Table Size ......................................................10-3/4 in. dia.
Table Movement...............................45° bevel, 360° swivel
Overall Height............................................................. 35 in.
Net Weight............................................................. 95.9 lbs.
laser
feed
laser on/off
handle
Variable
sPeed
leVer
workliGht
switch
dePth
GauGe
switch
key
Power
switch
sPindle
lock
knob
diGital
disPlay
lock
leVer
workliGht
on/off
switch
table
adjustment
handle
chuck
table
base
Fig. ꢀ
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW yOUR DRILL PRESS
FEED HANDLES
See Figure 2.
Feed handles raise and lower the chuck and bit during the
drilling operation.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
MOTOR
Your drill press is equipped with an industrial duty induction
motor for long-lasting, smooth performance.
BEVEL SCALE
The bevel scale indicates the degree the table is tilted.
SPINDLE LOCK LEVER
CHUCK
The spindle lock lever secures the spindle at the desired
depth for drilling.
Yourdrillpressfeaturesastandardthree-jawtypechuckwith
aself-ejectingchuckkey,whichpreventsaccidentallystarting
the drill press with the key still engaged in the chuck.
SPINDLE SPEED
Five different spindle speeds allow you to drill a wide variety
of material including wood, plastic, and metal.
DEPTH GAUGE
A depth gauge is located between the pulley housing and
feed handles to aid in drilling at desired depths.
TABLE
The table of your drill press rotates 360˚ a d bevels up to
45˚ for a gle drilli g.
DEPTH STOP
The adjustable locking depth stop permits accurate depth
measurement and repetitive drilling.
VARIABLE SPEED
Adjust drilling speed using the variable speed lever on the
side of the tool. Speed can only be changed when the tool
is on.
DIGITAL DISPLAy
Red numbers in the digital display show the RPM of the
tool.
VISE
CHUCK TOOL
The chuck tool is used to remove the chuck and chuck
spindle.
Use the vise to secure the workpiece to the table when
drilling.
EXACTLINE™ LASER
WORKLIGHT
The integrated worklight can be used to help illuminate the
work area. It requires a 15-watt, 1ꢀ0-volt, candelabra-base
bulb (not included).
The Exactline™ laser makes accurate, precision drilling
simple and easy.
TOOLS NEEDED
The following tools (not included) are needed for assembly and alignment:
adjustable wrench
mallet or
hammer
PhilliPs screwdriVer
Fig. 3
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOSE PARTS
The following items are included with the drill press:
Head Assembly .................................................................1
Column Assembly .............................................................1
Table..................................................................................1
Table Support....................................................................1
Base ..................................................................................1
Hex Key (3 mm, 4 mm, and 5 mm)....................................3
Hex Bolts (M8)...................................................................4
Feed Handles ....................................................................3
Worm Gear ........................................................................1
Spindle Lock Lever............................................................1
Table Adjustment Handle ..................................................1
Table Lock Handle.............................................................1
Variable Speed Lever ........................................................1
Chuck Tool.........................................................................1
Chuck ................................................................................1
Chuck Key.........................................................................1
Vise....................................................................................1
Operator’s Manual (not shown) .........................................1
head
assembly
Variable sPeed
leVer
hex key (3)
feed
handles
sPindle
table
adjustment
handle
(3)
lock
leVer
sPindle
chuck tool
worm
Gear
chuck
chuck
key
table
table suPPort
column
assembly
hex
bolts
table lock
handle
base
Vise
Fig. 4
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLy
UNPACKING
This product requires assembly.
ATTACHING COLUMN ASSEMBLy TO BASE
See Figure 5.
Place the base on a flat surface. Align screw holes in the
Carefully remove the tool and any accessories from the
column assembly with screw holes in the base.
box. Place it on a level work surface.
Place a hex bolt in each hole and tighten using an adjust-
NOTE: This tool is heavy. To avoid back injury, lift with
your legs, not your back, and get help when needed.
able wrench.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected the tool, identified all loose parts,
and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-5ꢀ5-ꢀ579 for assistance.
WARNING:
If any parts are damaged or missing do not operate this
tool until the missing parts are replaced. Failure to heed
this warning could result in possible serious personal
injury.
column
assembly
WARNING:
Do not attempt to modify this tool or create accesso-
ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
hex bolt
WARNING:
Do not connect to power supply until assembly is
complete. Failure to comply could result in accidental
starting and possible serious personal injury.
base
Fig. 5
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLy
INSTALLING TABLE ASSEMBLy
See Figures 6 - 8.
column
collar
Loosen the set screw in the column collar. Remove the
column collar and gear rack from the column and set
aside.
set
screw
table
Locate the worm gear and feed the D-shaft through the
suPPort
hole in the table support.
InstalltableadjustmenthandleovertheendoftheD-shaft
so that the flat side of the shaft aligns with the set screw.
Tighten the set screw using the hex key.
Feed the gear rack through the slot in the table assembly
sothattheteetharefacingoutandthelongersmoothend
faces up. The worm gear should engage the gear rack.
table
suPPort
table
adjustment
handle
Usingbothhands,slidetheentiretableassemblyandgear
rack onto the column until the bottom of the gear rack is
positioned in the base collar and against the column.
Slidethecolumncollar,bevel-sidedown,overthecolumn
until the beveled side engages the beveled end of the
gear rack. Tighten the set screw in the collar using the
hex key. Do not overtighten.
Gear
rack
set
screw
NOTE: You should be able to move the table from side
to side.
Locate the table lock handle. Insert it into the threaded
hole at the rear of the table assembly and tighten by
hand.
base
collar
d-shaft
Fig. 7
worm
Gear
slot
table
lock
handle
table suPPort
Fig. 6
threaded
hole
Fig. 8
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLy
INSTALLING CHUCK, HEAD ASSEMBLy, AND
FEED HANDLES
See Figures 9 - 11.
NOTE: Move the table out of the way before beginning
installation.
Position the head assembly onto the column with the
chuck positioned over the table.
NOTE: The head assembly is heavy. Get help when
needed.
Slide the head assembly down as far as it will go. Align
the head assembly with the base then tighten the two
head set screws with the hex key.
hub
feed
handle
Attach the three feed handles by screwing them into the
threaded holes in the hub.
Position chuck on spindle. Chuck should be fully opened
to avoid damaging jaws.
Using a piece of scrap wood to protect the chuck, firmly
tap the chuck into place using a mallet or hammer.
Fit the spindle into the spindle shaft turning it to the right
until it slips into place and tap with mallet using a piece
of wood.
Fig. 10
set
screws
head
assembly
head
assembly
sPindle
chuck
Fig. 9
Fig. 11
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLy
INSTALLING/CHANGING WORKLIGHT BULB
See Figure 12.
The integrated worklight can be used to help illuminate
the work area. The worklight requires a 15-watt, 1ꢀ0-volt,
candelabra-base bulb (not included).
To install, insert the bulb into the worklight receptacle and
twist clockwise to secure.
MOUNTING THE DRILL PRESS
See Figure 13.
If the drill press is to be used in a permanent location, secure
it to a workbench or other stable surface.
If the drill press is to be used as a portable tool, fasten it
permanentlytoamountingboardthatcaneasilybeclamped
to a workbench or other stable surface. The mounting board
should be of sufficient size to avoid tipping while drill press
is in use. Any good grade plywood or chipboard with a
3/4 in. thickness is recommended.
bulb
Fig. 1ꢀ
Mark holes on surface where drill press is to be mounted
using holes in drill press base as a template for hole pat-
tern.
Drill holes through mounting surface.
mountinG
bolts
Place drill press on mounting surface, aligning holes in
the base with holes drilled in the mounting surface.
Insert bolts (not included) and tighten securely with lock
washers and hex nuts (not included).
If lag bolts are used, make sure they are long enough to
go through holes in drill press base and material the drill
press is being mounted to. If machine bolts are used,
make sure bolts are long enough to go through holes in
drill press, the material being mounted to, and the lock
washers and hex nuts.
NOTE: All bolts should be inserted from the top. Install
the lock washers and hex nuts from the underside of the
workbench.
base
Once the drill press is securely mounted on a sturdy
surface perform the following:
Fig. 13
Check for vibration when the motor is switched ON.
Adjust and retighten the mounting hardware as
necessary.
Check the table assembly to assure smooth movement
up and down the column.
Check to assure that the spindle shaft moves smoothly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLy
INSTALLING/USING THE SPINDLE LOCK
LEVER
See Figure 14.
The spindle lock is installed by aligning the threaded post on
the lock lever with the hole on the left side of the tool then
turning the post clockwise. Securely tightening the spindle
lock lever locks the spindle in place. Turning the lock lever
counterclockwise will loosen the spindle.
CHECKING/ADJUSTING LASER ALIGNMENT
See Figure 15.
Check the laser alignment to ensure the intersection of the
laser lines is precisely at the spot where the drill bit meets
the workpiece. If it is not, the laser lines should be adjusted
using the laser adjustment knobs located on opposite sides
of the head assembly.
turn clockwise
to install / lock
the sPindle
Mark an “X” on a piece of scrap wood.
Fig. 14
Insert a small drill bit into the chuck and align its tip to
the intersection of the lines of the “X”.
Secure the board to the table.
Turn on the laser and verify the laser lines align with the
laser
housinG
“X” on the workpiece.
If the laser lines do not align, loosen the set screws on
each of the laser housings with a hex key and rotate the
laser adjustment knobs until the lines meet in the center
of the “X”. Retighten the set screws to secure.
WARNING:
Use of controls or adjustments or performance of
procedures other than those specified herein could result
in hazardous radiation exposure.
set
screw
DANGER
/
DANGER
/
PELIGRO
laser
adjustment
knob
D
Fig. 15
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
WARNING:
Always remove the switch key when the tool is not in
use and keep it in a safe place. In the event of a power
failure, turn the switch OFF (O) and remove the key. This
action will prevent the tool from accidentally starting when
power returns.
Do not allow familiarity with tools to make you care-
less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes re-
sulting in possible serious injury.
WARNING:
Always make sure the workpiece is not in contact with
the bit before operating the switch to start the tool. Fail-
ure to heed this warning may cause the workpiece to be
kicked back toward the operator and result in serious
personal injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Drilling in wood
Drilling in ceramics, plastics, fiberglass, and laminates
Drilling in metals
POWER SWITCH
See Figure 16.
switch
switch
off
The drill press is equipped with a power switch that has a
built-in locking feature. This feature is intended to prevent
unauthorized and possible hazardous use by children and
others.
on
TO TURN THE DRILL PRESS ON:
With the switch key inserted into the switch, lift the switch
to turn ON (l).
TO TURN THE DRILL PRESS OFF:
With the switch key inserted into the switch, push the
switch down to turn OFF (O).
TO LOCK THE DRILL PRESS:
Place the switch in the OFF (O) position.
Remove the switch key from the switch and store in a
switch
key
remoVed
secure location.
Fig. 16
18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SELF-EJECTING CHUCK KEy
See Figure 17.
Theself-ejectingchuckkeyensuresthechuckkeyisremoved
from the chuck before the drill press is turned on.
In order to loosen or tighten the chuck using the chuck key,
push the key into the key hole located on the chuck. Rotate
the key clockwise to tighten the chuck or counterclockwise
to loosen the chuck.
chuck key
WARNING:
Use only the self-ejecting chuck key provided. Always
remove chuck key. Failure to heed this warning could
result in serious personal injury.
key hole
Fig. 17
TABLE ROTATION
See Figure 18.
table
The table can be rotated out of the way when drilling large
objects.
Loosen the table lock handle.
table
lock
handle
Rotate the table to the desired position.
Retighten the table lock handle.
INSTALLING AND REMOVING BITS
See Figure 19.
Unplug the drill press.
Open or close the chuck jaws to a point where the open-
ing is slightly larger than the bit size you intend to use.
Insert drill bit into the chuck the full length of the jaws.
WARNING:
Do not insert drill bit into chuck jaws and tighten as shown
in figure 19. This could cause drill bit to be thrown from
the drill press, resulting in possible serious personal injury
or damage to the chuck.
Fig. 18
Tighten chuck jaws securely using chuck key provided.
Do not use a wrench to tighten or loosen chuck jaws.
Remove chuck key.
To remove the drill bit, reverse the steps listed above.
wronG
Fig. 19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Slowly lower drill bit into workpiece. Do not force the bit;
DRILLING
See Figures 20 - 21.
let the drill press do the work.
Once the hole is completed, allow the spindle to return to
its normal position. This will automatically raise the chuck
and bit.
Using the vise provided (or similar clamping devices),
secure the workpiece to the table. To protect the top
surface of the workpiece, use a piece of scrap wood
between the vise and the workpiece.
Select the proper drill bit based on the hole size desired.
For large holes, drill a pilot hole first, using a smaller
diameter bit.
Unlock the spindle lock lever and the lock knob. Using
the feed handles, set the spindle at the desired depth and
retighten both the lock lever and lock knob securely.
Turning the table adjustment handle, set the table to
desired height.
NOTE: Make sure the table is free of all loose objects and
the bit is not in contact with the workpiece.
Plug the electrical cord into power supply and turn the
switch ON. Make sure spindle rotates freely.
With the motor ru i g, cha ge the spi dle speed with
the variable speed lever.
DRILLING TIPS
If a large hole is needed, it’s a good idea to drill a smaller
pilot hole before drilling the final one. Your hole will be
more accurately positioned, rounder, and the bits will last
longer.
If the hole is deeper than it is wide, back off occasionally
to clear the chips.
When drilling metal, lubricate the bit with oil to improve
drilling action and increase bit life.
As you increase the bit size, you may need to reduce the
spindle speed.
If drilling a through hole, make sure that the bit will not
drill into the table after moving through the workpiece.
NOTE: The digital display on the front of the drill press
will give you the exact spindle speed. Use the chart below
to determine speed for the material and drill size.
Vise
hex
bolt
Variable
sPeed
leVer
Fig. ꢀ1
Fig. ꢀ0
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WARNING:
Before performing any adjustment, make sure the tool is
unplugged from the power supply. Failure to heed this
warning could result in serious personal injury.
ADJUSTING TABLE HEIGHT
See Figure 22.
beVel
scale
Hold the table with one hand and loosen the table lock
handle.
Rotate the table adjustment handle clockwise to raise the
table.
table lock
handle
table
adjustment
handle
Rotate the table adjustment handle counterclockwise to
lower the table.
Position the table to the desired height and retighten the
table lock handle.
Fig. ꢀꢀ
ADJUSTING TABLE BEVEL
See Figure 23.
The drill press is equipped with a tilting table that allows
you to drill angled holes. The table can be tilted left or right,
from 0º to 45º.
To tilt the table:
Loosen the large hex bolt located underneath the table.
Use the bevel scale to tilt the table to the desired
angle.
hex bolt
Retighten the hex bolt securely.
ADJUSTING THE DRILLING DEPTH
See Figure 24.
To adjust the drilling depth when you need to drill a number
of holes to exactly the same depth:
Fig. ꢀ3
Loosen the lock knob and the spindle lock lever.
Rotate depth gauge to the desired setting.
Retighten both the lock knob and the spindle lock lever
securely.
lock
knob
dePth
GauGe
Fig. ꢀ4
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LUBRICATION
Lower spindle to maximum depth and oil moderately once
WARNING:
every three months.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
Oil the column lightly every two months.
If cranking becomes difficult, grease gear rack lightly.
The ball bearings in the tool are permanently lubricated.
MOTOR/ELECTRICAL
WARNING:
The induction motor is easy to maintain but must be kept
clean. Do not allow water, oil, or sawdust to accumulate on
or in it. The sealed bearings are permanently lubricated and
need no further attention.
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
HEAD ASSEMBLy AND MOTOR HOUSING
WARNING:
Frequently blow out any dust that may accumulate inside
the head assembly and/or motor housing.
To prevent accidental starting that could cause possible
serious personal injury, turn off the tool, remove the
switch key, and unplug the drill press before performing
any maintenance or adjustment.
GEAR RACK
Periodically lubricate the worm gear and gear rack in order
to keep the vertical movement smooth and to help prolong
the life of the drill press.
GENERAL MAINTENANCE
REMOVING THE SPINDLE/CHUCK
The chuck tool is used to remove the chuck and/or spindle
when either an attachment is to be used or when large drill
bits with a tapered shank are to be used.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
Unplug the drill press.
Lower the spindle until the slots in the spindle are
WARNING:
visible.
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Insert the chuck tool into the spindle slot. While support-
ing the chuck in one hand, tap the chuck tool lightly with
a rubber mallet until the chuck and spindle release from
the drill press.
Remove the chuck tool from the spindle.
After usi g the drill press, clea it completely a d lubricate
allslidingandmovingparts.Applyalightcoatofautomotive-
type paste wax to the table and column to help keep the
surfaces clean.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Possible Cause
Solution
Noisy operation
Incorrect belt tension
Dry spindle
Adjust belt tension.
Lubricate spindle.
Tighten set screws in pulleys.
Loose spindle pulley or motor pulley
Bit burns or smokes
Incorrect speed
Change speed.
Chips not coming out of hole
Retract bit frequently to clear
chips.
Dull bit
Sharpen or replace bit.
Feeding too slow
Not lubricated
Feed fast enough; allow drill to cut.
Lubricate bit for metal work.
Excessive drill runout or wobble
Bent bit
Replace bit.
Bit not properly installed in chuck
Chuck not properly installed
Worn spindle bearings
Install bit properly.
Install chuck properly.
Contact authorized service center.
Drill bit binds in workpiece
Workpiece support loosens
Excessive feed pressure
Improper belt tension
Reduce feed pressure.
Adjust belt tension.
Workpiece not supported or clamped
properly
Check support and/or reclamp
workpiece.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR’S MANUAL
12 in. DIGITAL DRILL PRESS
DP121L
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simply contact your nearest Authorized Service Center. Be sure to provide all pertinent
facts when you call or visit. Please call 1-800-5ꢀ5-ꢀ579 for your nearest Authorized
list of Authorized Service Centers.
• MODEL NO. AND SERIAL NO.
The model number of this tool will be found on a plate attached to the motor housing.
Please record the model number and serial number in the space provided below.
• HOW TO ORDER REPAIR PARTS
When ordering repair parts, always give the following information:
DP1ꢀ1L
• MODEL NUMBER
• SERIAL NUMBER
Ryobi® is a registered trademark of Ryobi Limited used under license.
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
14ꢀ8 Pearman Dairy Road, Anderson, SC ꢀ96ꢀ5
Post Office Box 1ꢀ07, Anderson, SC ꢀ96ꢀꢀ-1ꢀ07
Tel.:1-800-5ꢀ5-ꢀ579
983000-64ꢀ
11-03-05 (REV: 01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|