Russound Stereo System ST2 XM User Guide

Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Product Introduction..........................................................................................................4-5  
Component Guide  
ST2-XM Front Panel.............................................................................................................6  
ST2-XM Rear Panel..............................................................................................................7  
ST2-RC Remote Control.......................................................................................................8  
ST2-XM Setup and Connections  
Basic Connections...............................................................................................................9  
ST2-KP and CAV6.6 ..........................................................................................................10  
CAi Series and A-BUS Connections.....................................................................................11  
Antenna Connections ....................................................................................................12-13  
ST2-XM Operation  
XM Radio Activation...........................................................................................................14  
XM Radio Displays.............................................................................................................14  
XM Radio Modes .........................................................................................................15-18  
Front Panel Controls..........................................................................................................19  
ST2-RC Remote Control.....................................................................................................20  
ST2-KP Keypad Controls....................................................................................................21  
UNO-S2 Keypad Controls with CAV6.6............................................................................22-23  
UNO-LRC1 Remote Control with CAV6.6.........................................................................24-25  
ST2-XM Tuner Programming  
ST2 Chassis Setup Menu...................................................................................................26  
Source Number .........................................................................................................26  
Update Firmware .......................................................................................................26  
Factory Initialization ...................................................................................................27  
System Info...............................................................................................................28  
Tuner Setup Menu for XM ..................................................................................................29  
Memory Name...........................................................................................................29  
Bank Name ...............................................................................................................30  
Controller ID..............................................................................................................30  
Diagnostics ...............................................................................................................30  
Factory Initialization ...................................................................................................30  
System Info...............................................................................................................31  
Tuner Setup Menu for AM/FM.............................................................................................31  
Memory Name...........................................................................................................31  
Bank Name ...............................................................................................................32  
Region ......................................................................................................................32  
Backup and Restore .........................................................................................................33  
Programming for CAV6.6 Use ............................................................................................34  
Technical Specifications ....................................................................................................35  
Warranty & Repair .............................................................................................................36  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
DESCRIPTION  
gration. It can also be controlled by IR signals  
received through the IR connections on the rear  
panel from IR repeating system commonly used  
in distributed audio systems.  
Thank you for choosing the Russound ST2-XM  
Smart Tuner. Whether you are adding radio to an  
existing system, expanding a CAi Series system  
or taking advantage of the CAV6.6’s robust  
If the ST2-XM Tuner is part of an RNET-enabled  
RNET™ communication link, the ST2-XM Tuner is system such as the CAV6.6-S2 system, the tuner  
designed to meet your needs.  
can be controlled through an RNET keypad such  
as the UNO-S2.  
The ST2-XM Tuner is like having two radios in  
one. The AM/FM tuner provides broadcast of  
local AM/FM stations, and the XM tuner delivers  
The ST2 Tuner also has an RS-232 port to sup-  
port fully bi-directional integration into whole-  
all the diversity and choices available to XM radio house control systems such as Crestron® and  
subscribers. The two modules share one set of  
controls and display on the front of the unit, but  
each runs independently. This arrangement  
allows two different broadcasts at the same time  
in a multi-room audio distribution system.  
AMX®.  
FEATURES  
• AM/FM Tuner  
• XM satellite radio  
• Compact single rack unit chassis  
• Six banks of six memory presets each per  
tuner (72 total presets) for storing AM/FM  
station settings or XM channels  
• Custom names for presets and banks  
• Two Favorite presets per tuner  
• Stereo or mono mode  
XM satellite radio provides over 100 channels of  
music, news sports, comedy, talk and entertain-  
ment. Its coast-to-coast coverage, digital quality  
sound and many commercial-free music channels  
make XM radio the choice for the discriminating  
listener.  
XM radio is a subscription-based service, and lis-  
teners can subscribe by visiting XM on the web  
www.xmradio.com or by calling XM’s Listener  
Care at 800-852-9696.  
• Local or distant mode  
• Dedicated IR remote control  
• Individual IR direct inputs for each tuner  
• Front panel IR receiver  
• Supports two ST2-KP optional tuner keypads  
• RNET connections send tuner frequency and  
control information to UNO keypad display  
• RS-232 control and programming. User  
settings can be backed up and restored.  
In addition to the traditional AM/FM broadcast  
tuner function and the XM satellite access, the  
ST2-XM Tuner can store up to 72 favorites, or  
memory presets. These are stored in groups of  
six called banks. There are six banks for each  
tuner. Each preset and each bank can be given a INSTALLATION APPLICATIONS  
custom name of your choice.  
RNET-enabled System  
When the ST2-XM Tuner is used with an RNET-  
The ST2-XM Tuner can be controlled from the  
front panel or by the dedicated ST2-KP tuner key- enabled device such as the CAV6.6 and is con-  
pad. It can also be controlled by the ST2-RC IR  
remote aimed at the tuner’s front panel IR receiv-  
er. The ST2-RC IR codes can be learned into any  
IR learning remote control for easy system inte-  
nected to it through the Link In or Link Out port,  
the tuner will be controlled by the CAV6.6  
through the UNO-S2 keypad. Through RNET,  
tuner information such as Tuner 1 or 2, station  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
INTRODUCTION  
frequency or channel, preset names and AM/FM  
band or XM is displayed on UNO-S2 keypads. An  
additional RNET device can be connected to an  
existing ST2 by using the Link Out of the first  
unit into the Link In of the second unit.  
tem with an audio distribution hub such as the  
A-H484 and IR-repeating keypads such as the  
A-KP2. The connections on the rear panel are  
designed to receive IR signals from a repeating  
system commonly used in A-BUS distributed  
audio systems.  
Before using the ST2-XM tuner with the  
CAV6.6, you must assign source numbers  
to Tuner 1 and 2 in the ST2 Setup Menu  
AND complete the CAV6.6’s Source Setup  
procedure to identify the tuner as a  
“Peripheral“ device and assign Source  
Numbers. The CAV6.6 requires firmware  
version 2.00.01 or higher to control each  
tuner through RNET. The UNO-S2 keypad  
requires firmware version 3.00.01 or  
higher.  
For A-BUS applications, as with the CAi series  
installation, the two tuners in the ST2-XM unit  
must be set up as two sources, with two source  
audio inputs and two IR connections. You will  
need two IR link cables for these connections.  
The two IR code sets can be learned from the  
ST2-RC remote into the A-LRC1 remote control.  
Note: Optional ST2-KP keypads can be used to  
provide control for the ST2-XM Tuner and are  
designed to be used with IR-controlled systems.  
IR-controlled System  
CAi Series -  
RS-232 Controlled System  
The ST2-XM Tuner can be controlled by infrared  
commands received through either of the two IR  
connections on the rear panel. There are two  
unique IR code sets for Tuner 1 and Tuner 2,  
which allow each to be controlled independently  
from either IR connection. These codes can be  
learned from the ST2-RC remote control into the  
CA-LRC1 remote control and/or the DSC and  
DAN IR learning keypads. The ST2-XM contains  
two individual tuners, which makes it act as two  
sources in the CAi system. There are two source  
audio outputs and two IR connections - one for  
each tuner in the ST2-XM. You will need at least  
one IR link cable (Russound P/N 09-0508) for  
these connections (one is supplied with each CAi  
system). If you are using an IR-controlled system  
from another manufacturer, installation should be  
similar. The ST2-XM IR codes may be learned  
into many other manufacturers’ remote controls  
that have learning capability for unified control  
over the A/V equipment.  
The ST2-XM Tuner can be controlled using the  
RNET protocol provided via the RS-232 port on  
the rear panel. It can also be controlled by any  
RS-232-enabled control system (e.g., Crestron,  
AMX). Information on RS-232 operation is avail-  
able to dealers on the Russound web site,  
BOX CONTENTS  
The ST2-XM Tuner comes with the parts needed  
to setup and operate the component. These  
include:  
• ST2 Tuner (AM/FM module, XM module)  
• ST2-RC remote control  
• 12VDC power supply  
• AM loop antenna (1)  
• FM antenna (1)  
• XM antenna (1)  
• RCA audio cable (2)  
• Rack mount ears  
®
A-BUS System -  
The ST2-XM Tuner can be used in an A-BUS sys-  
Please call Russound at 800-638-8055 ext. 501  
for assistance if parts are missing.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPONENT GUIDE  
ST2-XM FRONT PANEL  
1
2
3
XM  
64 : The Groove  
AM/FM  
5
6
4
7
8
9
10  
XM  
64 : The Groove  
AM/FM  
13  
12  
11  
1
MAIN POWER SWITCH - Turns power on and off  
POWER ON/OFF LED - Indicates power on or off  
2
3
4
5
6
REMOVABLE COVER LENS - Covers the selection buttons on the tuner  
BANK SELECT BUTTON - Selects bank 1-6  
MEMORY SELECT BUTTONS - Sets and selects memory presets 1-6 for each bank  
IR RECEIVER - Receives IR signal from remote control  
7
8
LCD PANEL - 12-character backlit display shows station, channel, custom names, etc.  
XM and AM/FM - Backlit tuner selection indicator  
9
TNR SEL - Selects Tuner 1 (XM) or Tuner 2 (AM/FM), and accesses tuner setup menus  
10  
BAND - (AM/FM) Selects AM or FM band  
(XM) Selects an XM Mode (Category Search, Now Playing, Display Preferences)  
(ALL) Enters menu selections when programming  
11  
ST/MONO - (AM/FM) Selects stereo or mono mode for AM/FM, and Distant/Local reception  
(XM) Press to Exit current XM Mode, hold for signal strength  
12  
13  
MEM PRESET UP/DOWN - Selects memory presets starting with last preset, and toggles  
through menu features  
TUNE UP/DOWN - (AM/FM) Manually selects radio stations  
(XM) Manually selects channels (Channel Up/Channel Down)  
(ALL) Toggles through menu settings  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPONENT GUIDE  
ST2-XM REAR PANEL  
2
3
4
5
6
7
8
9
10  
11  
1
LOOP  
Serial#  
12VDC 1.5A  
TUNER 2  
TUNER 1  
AUDIO OUTPUT  
ST2 Smart Tuner  
NEWMARKET, NH U.S.A.  
LINK  
ANTENNA  
FM COAX  
AUDIO OUTPUT  
RS-232  
KEYPAD PORTS  
L
R
L
R
IR  
INTEFACE  
IR  
ANTENNA  
IN  
OUT  
TUNER 2 AM/FM  
TUNER 1 XM  
1
RNET LINK IN/LINK OUT - Links to other Russound components that are RNET compatible, dis-  
plays frequency and other information on the UNO keypads  
2
RS-232 INTERFACE - The RS-232 Interface allows the tuner to be controlled by PC or other devices  
that have an RS-232 Interface. The RS-232 Interface also allows for firmware updates and program-  
ming (DB9 Cable)  
3
4
KEYPAD PORTS - RJ-45 Keypad ports for ST2-KP tuner keypads in dedicated, non-RNET sys-  
tems (Do not connect UNO keypads to these ports)  
FM COAX - FM Antenna threaded F-connection (75 ohms) for Tuner 2  
LOOP ANTENNA - AM antenna connection (300 ohms) for Tuner 2  
IR INPUT - IR control input (common IR control) for Tuner 2 or Tuner 1  
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 2  
XM ANTENNA - XM Antenna SMB connection (50 ohms) for Tuner 1  
IR INPUT - IR control input (common IR control) for Tuner 1 or Tuner 2  
AUDIO OUTPUT - Line-level audio signal outputs (RCA Cable) for Tuner 1  
POWER SUPPLY - 12VDC external power supply connection  
5
6
7
8
9
10  
11  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
COMPONENT GUIDE  
ST2-RC REMOTE CONTROL  
1
2
POWER - Puts the tuner in/out of standby mode  
1
2
TUNER CONTROL - Select TUNER 1 (XM) or  
TUNER 2 (AM/FM) and all subsequent button  
presses affect that tuner  
3
4
5
6
7
8
NUMERIC INPUT - Number buttons for direct  
selection of station, channel, bank, preset  
PWR  
BANK SELECT - Used for direct bank selection  
(numeric input 1-6)  
TUNER 1  
TUNER 2  
3
1
4
7
2
5
8
0
3
6
9
TUNE SELECT - Used for direct station or chan-  
nel selection (numeric input)  
15  
14  
4
5
TUNE UP/DOWN - Incrementally scrolls through  
station or channel numbers  
M
E
M
BANK  
FAV 1/FAV 2 - Sets/Selects Favorite 1 or 2  
preset selection on ST2-XM tuner  
6
7
TUNE  
SEEK UP/DOWN -  
AM/FM  
(AM/FM) Seeks the next tuned station  
up/down  
13  
12  
TUNE  
FAV 1  
SEEK  
FAV 2  
(XM) Scrolls through banks 1-6  
9
LOCAL/DISTANCE -  
SEEK  
OK  
(AM/FM) Optimizes station reception  
8
9
10  
OK -  
LOC/  
DX  
ST/  
MONO  
TUNE  
(AM/FM) Confirms direct entries  
(XM) Operating mode toggle  
11  
10  
11  
STEREO/MONO -  
(AM/FM) Selects stereo or mono broadcast  
(XM) Exit current XM operating mode  
12  
13  
TUNE UP/DOWN - Scrolls through station or  
channel numbers  
MEM UP/DOWN - Scrolls through preset sta-  
tions within selected bank  
14  
15  
AM/FM - Selects AM or FM band  
MEM SELECT - Used for direct memory select  
(numeric input 1-6)  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM SETUP AND CONNECTIONS  
BASIC CONNECTIONS  
Power  
ST2-KP RJ-45 Connection Wiring  
To power the tuner, connect the 12VDC external  
power supply by inserting the power supply jack  
into the power supply connection on the tuner’s  
rear panel.  
Audio Output  
Connect one end of a dual RCA audio cable to  
the Tuner 1 Audio Output connection. Keep prop-  
er channel identity. Attach the other end of the  
RCA cables to the source input of the audio con-  
trol system. Repeat the same procedure for the  
Tuner 2 Audio Output.  
IR Connections  
ST2-KP Keypad to ST2-XM Connection  
(Non-RNET System)  
The ST2-XM Tuner can be controlled by infrared  
commands received through the two IR connec-  
tions on the rear panel. The ST2-XM Tuner com-  
ponent contains two tuners, which must be set  
up as two sources. There are two IR connec-  
tions - one for each tuner in the ST2-XM. You will  
need two IR link cables (Russound P/N 09-0508)  
for these connections. There is a unique IR code  
set each for Tuner 1 and Tuner 2, which allow  
each to be controlled independently. These  
codes can be learned from the ST2-RC remote  
into learning-capable remotes and keypads.  
If you are using an IR-controlled system from  
another manufacturer, installation should be sim-  
ilar. The ST2-XM IR codes may be learned into  
many other manufacturers’ remote controls that  
have learning capability for unified control over  
the A/V equipment.  
The ST2-KP connects to the ST2-XM tuner with  
CAT-5 cable, using an RJ-45 (T568A) jack on the  
tuner connection end of the cable. Be sure to  
use the keypad ports for the ST2-KP and NOT  
the RNET link ports. The ST2-XM tuner supports  
up to two ST2-KP keypads. An SA-ZX3 Keypad  
Splitter can be used to add additional keypads.  
Note: ST2-KP keypads are designed for use  
with IR-controlled systems (non-RNET systems).  
When the ST2-XM Tuner is a component of an  
RNET system such as CAV6.6, the RNET-system  
keypads are used.  
Rack Mount Installation  
The ST2-XM can be mounted in a standard com-  
ponent rack using the rack ears provided. Line  
the rack ear’s two rows of screw holes with the  
three screw holes on the side of the tuner. Use  
the screws provided to secure the rack ears  
onto the unit on both sides. The ST2-XM tuner  
should not be installed above a high heat-pro-  
ducing component such as a power amplifier.  
RNET Connection  
To link the ST2-XM to an RNET-compatible  
device, use a CAT-5 passthrough patch cable  
with similar wiring terminations at each end.  
Connect one end of the cable to the RNET Link  
In of the ST2 tuner, and connect the other end  
of the patch cable to the RNET Link Out connec-  
tion on the RNET-compatible device.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM SETUP AND CONNECTIONS  
ST2-KP AND CAV6.6 CONNECTIONS  
CAT-5 Cable  
ST2-KP Connections to ST2-XM Tuner (Non-RNET Systems)  
The diagram depicts a standard ST2-KP keypad connection to the keypad port on the back of the  
ST2-XM. The keypad uses a 110 punchdown connection and an RJ-45 T568A connection to the tuner.  
UNO-S2  
keypads  
64:The Groove  
ST2 Tuner  
CAV6.6  
RCA Cable  
Source Connections with CAV6.6 Controller/Amplifier (RNET System)  
The diagram depicts a typical setup using the ST2-XM Tuner with a CAV6.6 amplifier. Each tuner in  
the ST2 unit must be connected as a separate source for audio inputs. UNO-S2 keypads are connect-  
ed to the CAV6.6 keypad ports, NOT the ports on the ST2 Tuner.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM SETUP AND CONNECTIONS  
CAi SERIES AND A-BUS CONNECTIONS  
VOLUME  
SOURCE  
STORE  
POWER  
REMOTE SENSOR  
ST2-KP  
CA-LCD2  
LOOP  
ANTENNA  
Serial#  
TUNER  
2
TUNER  
1
ST2 Smart Tuner  
NEWMARKET, NH U.S.A.  
LINK  
FM COAX  
AUDIO OUTPUT  
AUDIO OUTPUT  
RS-232  
KEYPAD PORTS  
L
R
L
R
INTERFACE  
IR  
IR  
12VDC 1.5A  
ANTENNA  
IN  
OUT  
IR Link Cable  
RCA Cable  
RCA Cable  
CA6.4i  
NEWMARKET, NH U.S.A.  
ZONE PREAMP  
OUTPUTS  
KEYPAD PORTS  
SOURCE INPUTS  
1
2
3
4
5
6
1
2
1
2
3
4
~220-240VAC  
~110VAC  
VARIABLE  
FIXED  
VARIABLE  
R
L
R
FIXED  
L
OUTPUT TO  
3
8
OHM SPEAKER  
4
1
2
5
6
VOLTAGE FUSE  
110V F4A  
220-240V F2A  
LINK  
OUT  
MUTE  
OUT  
IR EMITTERS  
12V TRIG  
IN  
IN  
WARNING : SHOCK HAZARD – DO NOT OPEN  
~110VAC  
~220-240VAC  
~50-60Hz  
400W  
AVIS : RISQUE DE CHOC ELECTRIQUE –  
NES PAS OUVRIR.  
SERIAL #  
RCA Cable  
IR Link Cable  
Pos (+)  
Neg (–)  
Source Connections with CAi Series Controller/Amplifier  
The diagram depicts a typical setup using the ST2-XM Tuner with a CAi Series amplifier. Each tuner in  
the ST2 unit must be connected as a separate source for audio inputs.  
A-KP2  
ST2-KP  
LOOP  
LOOP  
Serial#  
TUNER  
2
TUNER  
1
ST2 Smart Tuner  
NEWMARKET, NH U.S.A.  
LINK  
ANTENNA  
ANTENNA  
FM COAX  
FM COAX  
AUDIO OUTPUT  
AUDIO OUTPUT  
RS-232  
KEYPAD PORTS  
L
R
L
R
INTERFACE  
IR  
IR  
12VDC 1.5A  
IN  
OUT  
RCA Cable  
RCA Cable  
IR Link Cable  
IR Link Cable  
SOURCE AUDIO INPUT  
NEWMARKET, NH U.S.A.  
LINK  
L
IN  
OUT  
R
TRIGGER OUT  
12VDC  
100mA  
1
2
3
4
SYSTEM ON  
SOURCE IR  
COMMON IR  
4
COUPLED-ZONE, 4-SOURCE  
PANEL MOUNT AUDIO HUB  
A/B COUPLED-ZONE OUTPUT  
2A 3A  
1A  
4A  
POWER FOR  
KEYPADS  
A
OUTPUT TO  
KEYPADS  
A
RCA Cable  
IR Link Cable  
+24V  
4A  
Pos (+)  
Neg (–)  
OUTPUT TO  
BKEYPADS  
POWER FOR  
1B  
2B  
3B  
4B  
B
KEYPADS  
SERIAL#  
A-H484  
Source Connections with A-BUS Audio Distribution Hub  
The diagram depicts a typical setup using the ST2-XM Tuner with an A-BUS system’s audio distribu-  
tion hub. Each tuner in the ST2 unit must be connected as a separate source for audio and IR inputs.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM SETUP AND CONNECTIONS  
ANTENNA CONNECTIONS  
XM Antenna  
XM Signal Strength Mode  
Connect the included XM antenna for XM recep-  
tion to the back panel of the XM module. The  
antenna comes with 20 feet of cable. If this  
length is not sufficient, there are aftermarket  
antenna kits available for custom lengths.  
Position the antenna near a south-facing window  
to receive the best signal from a satellite or ter-  
restrial signal.  
To test the XM reception, turn the unit on. When  
the XM radio is powered for the first time, the  
XM service will start playing XM Channel 1, a  
preview/promotional channel. Verify that Channel  
1 is playing by pressing the Tune Up/Tune Down  
buttons. Enter Signal Strength Mode by pressing  
and holding the ST/MONO button on the ST2-XM  
front panel. The display shows one of the follow-  
ing:  
The antenna may also be attached to an exter-  
nal wall by sliding the slots on the back of the  
antenna onto four screws mounted on an exteri-  
or wall. Establish the best receiving position for  
the antenna before attaching it to the wall.  
GOOD SIGNAL Signal strength good  
MARGINAL SIG Signal strength marginal  
POOR SIGNAL Signal strength poor  
NO SIGNAL  
Loss of signal  
Adjust the antenna until GOOD SIGNAL is dis-  
played. Press ST/MONO to exit Signal Strength  
Mode.  
75 ohm  
to 300 ohm  
balun  
Connecting an Indoor and Outdoor Antenna  
The diagram above depicts a typical setup using the ST2-XM Tuner with the included XM antenna, FM  
antenna and AM loop antenna. Also shown are two outdoor antenna options (not included).  
(Not to scale)  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM SETUP AND CONNECTIONS  
ANTENNA CONNECTIONS  
AM Antenna  
FM Antenna  
Connect the included loop antenna for AM recep-  
tion to the back panel, attaching the GND  
Attach the included FM antenna to the Tuner 2  
FM COAX connection on the back panel by push-  
(ground) and AM ends to the appropriate connec- ing the F-type quick-connect termination of the  
tions for Tuner 2.  
antenna onto the FM connection.  
It is recommended to use an external outdoor or  
attic-mounted long wire antenna for best per-  
formance for AM reception. Use a 75-ohm to  
300-ohm balun at the AM connection on the  
tuner, and attach the 75-ohm coax cable to the  
balun.  
It is recommended to use an external outdoor or  
attic-mounted long wire antenna for best per-  
formance for FM reception. Attach the desired  
length of 75-ohm coax cable directly to the FM  
connection on the tuner.  
Antenna  
Lead In Wire  
Electric  
Service  
Equipment  
Power Service  
Grounding  
Electrode System  
Grounding  
Conductors  
Ground  
Clamps  
Grounding an Outdoor Antenna  
If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges  
and voltage surges. Consult the instructions that came with the antenna or contact the antenna manu-  
facturer for proper installation instructions. The diagram gives a general depiction of how an outdoor  
antenna should be grounded. For complete guidelines on antenna grounding procedures, please con-  
sult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
XM RADIO OVERVIEW  
XM Radio Activation  
XM Radio is over 100 channels of radio broadcasts with the signal delivered by satellite and (depend-  
ing on location) transferred by terrestrial antennas. The radio is a subscription-based service with a  
monthly provider fee and an activation charge. XM radio broadcasts several channels for preview but  
will not broadcast the full range of channels without activation. Activation and billing are handled sole-  
ly through XM Radio.  
To activate the XM tuner:  
1
Turn on the power, select the XM Tuner, and select channel 0. The tuner’s eight-character XM  
satellite Radio ID number will appear on the display. Write the number down to have it available  
when contacting XM Radio for activation. The number is also shown on the back of the unit and  
on the product box.  
2. To subscribe, have a major credit card and your XM Radio ID number at hand and contact XM at  
1-800-852-9696. You will be guided through the activation process step by step.  
3. A complete and up-to-date full channel listing is available on the XM Radio website,  
XM Radio Displays  
In addition to Channel and Category information, the XM tuner will broadcast operating condition mes-  
sages when the following conditions occur:  
Display  
ANTENNA  
UPDATING  
LOADING  
OFF AIR  
CH - - -  
Condition  
Antenna not connected  
Updating encryption code  
Acquiring channel audio or information  
Channel not in service  
Channel (SID) no longer available  
Corresponding Artist Name or Song Title are null (empty)  
No channel available for the chosen category  
- - - - - -  
- - - - - -  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
XM RADIO MODES  
XM Radio Modes  
There are four user “modes” for selecting music and viewing music information on the XM Tuner:  
Preset (default or normal)  
Category Search  
Now Playing  
Display Preferences.  
These modes are accessed through certain button and key presses from the tuner panel, remote  
controls and keypads. When choosing modes, if no choice is made after 20 seconds, the tuner will  
time out by showing EXIT and return to tuner display and Preset mode.  
For all XM Modes  
The chart below outlines the button presses for various XM tuner functions outside of the XM modes.  
ST2-XM  
ST2-RC ST2-KP  
UNO-S2  
UNO-LRC1  
All User Modes  
OK  
Operating Mode Toggle  
ST/  
MONO  
Exit Current Mode  
Signal Strength  
Hold  
Hold  
Hold  
Operating Mode Toggle  
This button press accesses the three non-default XM modes. The three modes will appear in order:  
Category Search, Now Playing and Display Preferences.  
Exit Current Mode  
This button press returns the XM tuner to Preset (default) mode.  
Signal Strength  
This button press and hold accesses the Signal Strength mode. Depending on the signal, the follow-  
ing will be displayed:  
GOOD SIGNAL Signal strength good  
MARGINAL SIG Signal strength marginal  
POOR SIGNAL Signal strength poor  
NO SIGNAL  
Loss of signal  
Press the appropriate button again to exit Signal Strength Mode.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
XM RADIO MODES  
Preset (default) Mode  
This is the normal operating mode of the XM tuner. In this mode the XM tuner operates similarly to  
the AM/FM tuner for channel up and down, bank selection and memory presets.  
Next Preset  
This button press accesses the next saved preset (6 presets for each bank) in the chosen bank.  
Previous Preset  
This button press accesses the previous saved preset in the chosen bank  
Next Bank  
This button press accesses the next bank (total of 6 banks).  
Previous Bank  
This button press accesses the previous bank.  
Channel Up  
This button press accesses the next active channel up from the current channel.  
Channel Down  
This button press accesses the next active channel down from the current channel.  
ST2-XM  
ST2-RC  
ST2-KP  
UNO-S2  
UNO-LRC1  
Preset Mode  
Next Preset  
MEM  
MEM  
Previous Preset  
Next Bank  
Hold  
Hold  
Hold  
Hold  
Hold  
Hold  
Previous Bank  
Channel Up  
Channel Down  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
XM RADIO MODES  
1.CAT SEARCH  
Category Search Mode (  
)
XM Radio is organized by Channel Category (e.g., Rock, Country, News). Within each category is  
a series of channels (e.g., Top Tracks, Bluegrass Junction, XM Classics). Channel selection in this  
mode is refined to scrolling only those channels in the selected category.  
Next Category  
This button press accesses the next category from the current category.  
Previous Category  
This button press accesses the previous category from the current category.  
Category Channel Up  
This button press accesses the next channel up within the selected category.  
Category Channel Down  
This button press accesses the next channel down within the selected category.  
ST2-XM  
ST2-RC  
ST2-KP UNO-S2  
UNO-LRC1  
OK  
Category Search Mode  
Next Category  
MEM  
MEM  
Previous Category  
Category Channel Up  
Category Channel Down  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
XM RADIO MODES  
2.NOW PLAYNG  
Now Playing Mode (  
)
This mode displays information about the current XM selection. Appropriate button presses access  
the next or previous information item.  
NAME:  
Displays the artist’s name, feature name or program name (news, talk, sports).  
TITLE:  
Displays the song title or program title.  
CATEGORY:  
Displays the current category.  
ST2-XM  
ST2-RC  
ST2-KP UNO-S2  
UNO-LRC1  
OK  
Now Playing Mode  
Next Info Item  
MEM  
MEM  
MEM  
MEM  
Previous Info Item  
3.DSPLY PREF  
Display Preference Mode (  
)
This mode allows you to choose how XM channel information will be displayed on the keypad and  
tuner. Appropriate button presses access the next or previous preference item.  
Note: For any display configuration, the artist’s name and song title will scroll before the display  
returns to the designated display format.  
Channel Number (CH NUMBER:)  
This selection displays the channel number only (e.g., XM070, XM103).  
Channel Name (CH NAME:)  
This selection displays the channel name only (e.g., ESPN Radio, Real Jazz).  
Channel Number and Name (#:CH NAME:)  
This selection displays the channel number and name (e.g., 64:The Groove, 121:Fox News).  
ST2-XM  
ST2-RC  
ST2-KP UNO-S2  
UNO-LRC1  
OK  
Display Preference Mode  
Next Display Preference  
MEM  
MEM  
MEM  
MEM  
Previous Display Preference  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
FRONT PANEL CONTROLS  
screen when selecting mode. Normal operation is in  
Distant mode. In cities, antennas can pick up multi-  
path signals when they bounce off buildings and get  
doubled. The Local mode limits the noise associated  
with these reflected signals.  
Front Panel Operation  
Turning the unit on  
To turn the unit on, push the On/Off button up on the  
front panel. Pushing the On/Off button down turns the  
tuner off.  
Bank/Memory Presets  
Selecting the desired tuner  
Each tuner has six banks of preset memory settings,  
and each bank holds six presets for a total of 36 pos-  
sible presets for each tuner (72 total presets).  
Presets are associated with the tuner that is selected  
at the time the preset is saved.  
From the front panel, use  
to toggle between XM  
and AM/FM. A backlight shows behind the selected  
label XM (green) or AM/FM (amber) to indicate the  
active tuner. In addition, the LCD panel is also backlit  
green for Tuner 1 and amber for Tuner 2. Each time a  
tuner is selected the display will refresh with the cur-  
rent station or preset, and all subsequent memory  
preset entries will be associated with that selected  
tuner.  
Memory Preset programming  
From the front panel, perform these steps:  
1. Select a tuner using  
.
Selecting the desired band (AM/FM only)  
2. Use to choose from one of six banks (1-6).  
Push  
to switch between AM and FM reception.  
3. If AM/FM, select the desired band using  
.
Selecting a mode (XM)  
4. Tune to the desired station or channel.  
5. Push the desired memory preset (M1 through M6)  
button for more than 2 seconds. When the memory  
preset is saved, the appropriate preset number (M1  
through M6) and SAVED appears on the LCD. The  
selected station setting reappears and the sound  
resumes after the button is released.  
Push  
to select an XM operating mode.  
Exiting a mode (XM)  
Push  
to exit the XM mode selection menu.  
Signal Strength mode (XM)  
Recalling a Memory Preset  
Press and hold  
and release. The display shows  
the signal strength rating. To exit press  
.
To recall a memory preset, use  
to select the  
desired bank, then press the desired preset button  
(M1 to M6). In addition to direct selection, the memo-  
Selecting the desired frequency or channel  
Press and release  
and  
for manual tuning.  
ry presets can be accessed by using  
scroll through all presets for the bank selected.  
and  
to  
Selecting Stereo or Mono Output (AM/FM  
only)  
Backup and Restore  
Once all of the tuner settings are completed, it may  
be advisable to create a backup of the programmed  
settings for future use. The backup will then be avail-  
able in case tuner settings need to be restored. The  
“RNET Backup Utility” is available through the  
Document Center at www.russound.com. Also  
required are a DB9 male-to-female cable and laptop  
or desktop PC.  
Press and release  
mono mode. STEREO or MONO appears briefly on the  
screen when selecting mode.  
to toggle between stereo and  
Selecting Distant or Local Reception  
(AM/FM only)  
Press and hold  
local mode. DISTANT or LOCAL appears briefly on the  
to toggle between distant and  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
ST2-RC REMOTE CONTROL  
Frequency Seek (AM/FM only)  
The SEEK function is performed by pressing and  
ST2-RC Remote Control Operation  
The ST2-RC remote control is the only means of  
remote operation of the ST2-XM in a non--RNET sys-  
tem. The ST2-XM front panel displays information for  
the tuner that is receiving commands from the ST2-  
RC. However, the ST2-RC commands do not change  
which tuner is playing; that is done through the sys-  
tem’s source selection.  
releasing  
to seek lower frequencies or  
for  
higher frequencies. SEEK tuning begins at the current  
frequency, seeks upward and stops at the next tuned  
station. Pushing  
continues the SEEK function.  
Once the highest frequency is reached, the tuner con-  
tinues in SEEK mode at the lowest frequency.  
Turning the unit on/off  
Selecting Stereo or Mono Output  
(AM/FM only)  
To switch the ST2 tuner in or out of standby mode,  
PWR  
push  
or any other button except TUNER 1 or  
ST/  
MONO  
TUNER 2.  
Press  
to toggle between stereo and mono mode.  
STEREO or MONO appears briefly on the screen when  
selecting mode. Normal operation is in stereo mode.  
On a preset, the stereo/mono setting is saved for  
that preset.  
Selecting the desired tuner  
TUNER 1  
TUNER 2  
To control a tuner, push  
or  
. When  
pressed, these buttons will be backlit green for Tuner  
1 (XM) and amber for Tuner 2 (AM/FM). Each time a  
tuner is selected the display will refresh with the cur-  
rent station or preset for that tuner, and all subse-  
quent button presses and memory preset entries will  
be associated with that selected tuner.  
Selecting Distant or Local Reception  
(AM/FM only)  
LOC/  
DX  
Press  
to toggle between Distant and Local  
mode. DISTANT or LOCAL appears briefly on the  
screen when selecting mode. Normal operation is in  
Distant mode.  
Selecting the desired band (AM/FM only)  
AM/FM  
Push  
to switch between AM and FM reception.  
Recalling a Memory Preset  
Selecting the desired frequency or channel  
To recall a memory preset, select the desired tuner,  
BANK  
press  
and enter the desired bank number  
Use  
and  
for manual tuning. To move quickly  
through the stations or channels, press and hold  
either of the Tune buttons for more than 1.5 seconds.  
M
EM  
(1-6), then press  
and enter the desired preset  
number (1 to 6). The memory presets can also be  
MEM  
TUNE  
To directly select a station or channel, press  
,
MEM  
accessed by using  
and  
to scroll through all  
and enter the two- or three-digit XM channel number,  
or the three- or four-digit station frequency (1071 for  
107.1, etc.). European regions use five-digit station  
frequencies.  
presets for the selected bank.  
Saving Favorites  
The remote control stores two “favorites” (similar to  
memory presets) per tuner. These are set simply by  
selecting either Tuner 1 or Tuner 2, setting the  
Selecting a mode (XM)  
OK  
FAV 1  
Push  
to select an XM operating mode.  
desired frequency and pressing and holding  
or  
FAV 2  
Exiting a mode (XM)  
until “FAV1 (2) saved” appears on the tuner.  
Stored Favorites are then recalled by pressing either  
ST/  
MONO  
Push  
to exit the XM operating mode selection  
FAV 1  
FAV 2  
menu.  
or  
.
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
ST2-KP KEYPAD CONTROLS  
ST2-KP Keypad Operation  
4
Selecting a Bank  
To select a bank, select the desired tuner, then press  
1
Turning the keypad on/off  
and hold or to select the desired bank. The  
bank name will show on the display.  
To activate the ST2-KP, press  
power down the keypad display. The keypad remains  
powered until the ST2-XM Tuner is turned off.  
. Press  
to  
4
Recalling a Memory Preset  
1
Selecting the desired tuner  
To recall a memory preset, press and release  
or  
To select a different tuner, press and hold  
. (If the  
keypad has been hardware jumper-selected to Tuner  
1 or Tuner 2, it will not switch between the two  
tuners.) The backlight color of the display will be  
green for Tuner 1 (XM) and amber for Tuner 2  
(AM/FM). Each time a tuner is selected the display  
will refresh with the current station or preset for that  
tuner, and all subsequent button presses and memo-  
ry preset entries will be associated with that selected  
tuner.  
to scroll through the presets for the selected  
bank. (Memory presets must be stored for ST2-KP  
recall)  
5
ST2-KP Keypad Display  
The 5-character backlit display shows frequency and  
band, plus XM channel and mode information.  
Messages scroll twice, then display the first 5 char-  
acters.  
2
Selecting the desired band (AM/FM)  
Push  
to switch between AM or FM band.  
ST2-KP Keypad-Front Panel  
2
Selecting a mode (XM)  
Push  
to select an XM operating mode.  
2
Exiting a mode (XM)  
Press and release  
the XM operating mode menu.  
until EXIT is displayed to exit  
5
3
Selecting the desired frequency or  
channel  
3
2
Use  
and  
for manual tuning. To move quickly  
or  
3
through the channels, press and hold either  
1
for more than 1.5 seconds. European frequen-  
cies show in .05 MHz increments.  
4
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
UNO-S2 KEYPAD CONTROLS WITH CAV6.6  
Frequency Seek (AM/FM only)  
A press on will seek the next higher tune-  
able station. If a tuneable station is not found,  
CAV6.6-UNO-S2 Keypad Operation  
NOTE: To control the ST2 Tuner through the  
UNO-S2 keypad, the tuner must be configured  
as a source using the CAV6.6 programming  
steps.  
end the SEEK function by pressing  
Frequency Scan (AM/FM only)  
To scan, press and hold then release  
again.  
Turning the unit on  
The tuner is power managed by the CAV6.6 or other  
RNET-enabled controller. If the tuner is in standby  
mode, any button press of the UNO-S2 keypad will  
bring the tuner out of standby mode.  
. The  
tuner scans through tuned stations with a 5-sec-  
ond preview before moving to the next station.  
Selecting the desired tuner  
To end scanning, press  
again.  
On the UNO-S2 keypad, press  
to select  
Signal Strength Mode (XM)  
either Tuner 1 (XM) or Tuner 2 (AM/FM) by  
choosing the tuner’s preassigned source num-  
ber.  
To check XM signal strength, press and hold  
then release. The display shows the signal  
strength rating. To exit, press  
Selecting a Bank  
again.  
Selecting the desired band (AM/FM only)  
Push  
to toggle between AM band and FM  
To select a bank, press and hold  
for bank  
band reception.  
up or  
for bank down. The bank’s name will  
Selecting a Mode (XM)  
be temporarily displayed on the UNO-S2.  
Push  
to toggle between XM modes.  
Recalling a Memory Preset  
Exiting a Mode (XM)  
Press  
and  
to scroll through the memo-  
Press  
until EXIT is displayed to  
and release  
ry presets for the selected bank. This procedure  
will step through all of the presets in the current  
bank, then loop back to start at the first one.  
Only configured presets will be displayed.  
exit XM mode selection menu.  
Selecting the desired frequency or channel  
Use  
and  
for manual tuning or channel  
selection. The frequency or channel will appear  
on the keypad and the active tuner. To move  
quickly through the channels, press and hold  
Mute  
Press  
to mute/unmute the tuner audio output.  
either  
or  
for more than 1.5 seconds.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
UNO-S2 KEYPAD CONTROLS WITH CAV6.6  
1
6
5
2
4
3
1
2
3
4
SCAN - (press and hold)  
TUNER SELECTION - Select source number  
assigned to TUNER 1 (XM) or TUNER 2 (AM/FM)  
(AM/FM) Scans through tuned stations with  
5-second preview before next station  
(XM) Signal Strength mode toggle  
TUNE UP/DOWN - Used for manual station or  
channel selection  
5
6
MUTE - Mutes/unmutes tuner audio output  
SELECT -  
BANK SELECT - Used for bank selection (press  
and hold)  
(AM/FM) Selects AM or FM band  
(XM) Operating mode toggle  
6
MEM UP/DOWN - Scrolls through memory preset  
stations (press)  
4
SEEK - (press)  
(AM/FM) Seeks next higher tuned station  
(XM) Exit current XM mode  
NOTE: UNO-S2 keypads are connected to the  
CAV6.6 to control the ST2-XM through RNET.  
UNO-S2 keypads do not connect directly to  
the ST2 Tuner.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
UNO-LRC1 REMOTE CONTROL WITH CAV6.6  
digit station frequencies.  
UNO-LRC1 Remote Control Operation  
Turning the unit on  
Frequency Seek (AM/FM only)  
The tuner is power managed by the CAV6.6 or other  
RNET-enabled controller. If the tuner is in standby  
mode, any button press of the UNO-LRC1 will bring  
the tuner out of standby mode when used with the  
UNO keypad.  
The SEEK function is performed by pressing and  
releasing the Select  
or  
or  
. Press  
. To seek  
for  
higher frequency station press  
Selecting the desired tuner  
lower frequencies. Tuning begins at the current fre-  
quency, seeks upward (or downward) and stops at the  
To select a tuner, push  
and choose the source  
number preassigned to Tuner 1 (XM) or Tuner 2  
(AM/FM), or use the UNO numeric source inputs at  
the bottom of the UNO-LRC1.  
next tuned station. Pushing  
or  
again con-  
tinues the SEEK function. Once the highest frequency  
is reached, the tuner continues SEEK mode at the  
lowest frequency.  
Selecting the desired band (AM/FM only)  
Frequency Scan (AM/FM only)  
Push  
to toggle between AM/FM reception.  
To scan, press and hold then release  
. The  
Selecting a Mode (XM)  
tuner scans through tuned stations with a 5-second  
preview before moving to the next station. To end  
Push  
,
or  
to toggle between XM  
operating modes.  
scanning, press  
again.  
Exiting a Mode (XM)  
Selecting a Bank  
Press  
or  
to exit XM operating mode menu.  
To select a bank, press and hold  
or for bank down.  
for bank up  
to scroll  
Signal Strength mode (XM)  
Press and hold  
and release. The display shows  
the signal strength rating. To exit press  
.
Recalling a Memory Preset  
Selecting the desired frequency or channel  
Press  
and  
or  
and  
Use the Channel  
and  
or  
and  
through a loop of all the memory presets for the cur-  
rently selected bank. Only configured presets will be  
displayed.  
for manual tuning. To move quickly through the  
channels, press and hold the button for more than  
1.5 seconds. To directly select a station or channel,  
enter the three- or four-digit channel or frequency  
(1071 for 107.1, etc.). European regions use five-  
Mute  
Press the  
button to mute/unmute the tuner  
audio output.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM OPERATION  
UNO-LRC1 REMOTE CONTROL WITH CAV6.6  
1
2
POWER - Power managed by CAV6.6  
UNO SELECTION - UNO must be the  
selected source for control of the  
CAV6.6 and any connected compo-  
nents. Select UNO before sending  
UNO-LRC1 remote commands.  
NUMERIC INPUT - Number buttons for direct  
input of frequency, channel, preset, bank  
3
TUNE UP/DOWN - Incrementally scrolls through  
channels or tuned stations  
4
5
EXIT - Exit XM operating mode  
1
2
TUNE UP/DOWN - Incrementally scrolls through  
channels or tuned stations  
6
SELECT -  
(AM/FM) Confirms numeric selection  
(XM) Operating mode toggle  
7
8
MENU - XM operating mode toggle  
PLAY -  
(AM/FM) Selects AM or FM band  
(XM) Operating mode toggle  
3
4
9
9
BANK UP/DOWN - Used for bank selection (press  
and hold)  
12  
15  
5
6
5
7
8
MEM UP/DOWN - Scrolls through memory pre-  
sets for selected bank (press)  
14  
13  
10  
11  
MUTE - Mutes/unmutes tuner audio output  
SCAN - (SEEK - press, see #14 below)  
(AM/FM) Scans through tuned stations with 5-  
second preview before next station (press and  
hold)  
9
12  
(XM) Exit XM operating mode  
10  
12  
TUNER SELECTION - Select source number  
assigned to TUNER 1 (XM) or TUNER 2 (AM/FM)  
11  
13  
14  
INFO - XM Now Playing mode toggle  
SEEK UP/DOWN -  
(AM/FM) Seeks next tuned station up/down  
(XM) Next/previous preset, category, info item,  
display preference  
15  
GUIDE - XM Category Search mode toggle  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
ST2-XM Tuner Setup Menus  
Note: The Setup Menu procedures must be performed from the ST2-XM Tuner front panel.  
The ST2-XM Tuner Setup Menus provide setup and naming procedures for the ST2-XM main chassis,  
the XM tuner module and the AM/FM tuner module. These procedures include source number assign-  
ments, assigning a custom name to a memory preset or a bank, choosing a region for AM/FM opera-  
tion (US or Euro), factory initialization and system information.  
If the ST2-XM is used with a non-RNET system, the ST2-XM can be connected and operated without  
any setup programming. Follow the setup menus if custom names are desired, or for system info.  
If the ST2-XM is used with an RNET system such as CAV6.6, the following minimum setup must be  
performed for the ST2-XM to be properly controlled by the CAV6.6.  
1. ST2 Chassis Setup Menu - Assign source numbers to Tuner 1 and Tuner 2.  
2. CAV6.6 Source Setup Menu - Assign the corresponding source numbers to Tuner 1 and Tuner 2.  
3. CAV6.6 Source Setup Menu - Assign command type PERIPHERAL to Tuner 1 and Tuner 2.  
NOTE: Once the programming procedures are completed, cycle power first to the Tuner and then  
to the CAV6.6 (must be powered on last) to establish a connection.  
9. Press TNR SEL to exit the Source Number  
ST2 Chassis Setup Menu  
menu.  
Source Number (Chassis)  
The Source Number procedure permits Tuner 1  
Update Firmware (Chassis)  
The Update Firmware procedure allows the ST2  
tuner’s OS firmware to be updated. The proce-  
dure is performed using a DB9 serial cable with  
(XM) and Tuner 2 (AM/FM) to be assigned the  
proper peripheral source identities as will be  
assigned in the CAV6.6 Source Setup.  
1. Enter the Setup Menu by pressing and holding one end connected to the RS-232 port on the  
the TNR SEL button.  
back of the tuner and the other connected to a  
PC or laptop. If an OS firmware update is avail-  
able, it can be obtained through the Document  
Center at www.russound.com. XM tuner module  
2. TUNER SETUP appears. Press MEM Up/Down  
until SOURCE NUM appears on the tuner.  
3. Press BAND. TUNER # appears.  
4. Press the Tune Up/Down buttons to select the firmware must be performed by an authorized  
Tuner # (Tuner 1 is XM, Tuner 2 is AM/FM).  
5. Press BAND. SOURCE NUM appears.  
6. Press the Tune Up/Down buttons to scroll  
through the source numbers 1-6.  
Russound service facility.  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
7. Press BAND to select the source number (as  
assigned in the CAV6.6 setup process).  
8. Repeat the process for the next tuner.  
2. TUNER SETUP appears. Press MEM Up/Down  
until UPDATE FIRMW appears on the tuner.  
3. Press BAND to enter the UPDATE FIRMW menu.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
Press and Hold  
TNR SEL button  
ST2 Chassis Setup Procedures  
TNR  
SEL  
TNR  
SEL  
TUNER  
SETUP  
Menu  
SOURCE  
NUM  
Procedure  
Chassis  
Setup  
Menu  
UPDATE  
FIRMW  
Procedure  
FACTORY  
INIT  
Procedure  
SYSTEM  
INFO  
Procedure  
TNR  
SEL  
TNR  
SEL  
This  
Procedure  
returns the  
ST2 Tuner  
to its  
HOLD  
BAND  
TUNER  
#
Factory  
settings  
After update  
cycle Power  
Are you sure  
SOURCE  
NUM  
Start  
Update  
YES  
NO  
Cycle Power  
Please wait  
Cycle Power  
4. “Hold BAND” appears on the tuner.  
the TNR SEL button.  
2. TUNER SETUP appears. Press MEM Up/Down  
until FACTORY INIT appears on the tuner.  
5. While pressing and holding BAND, “After  
update cycle power” appears on the tuner  
display.  
3. Press BAND to enter the FACTORY INIT menu.  
6. When “Start Update” appears on the tuner dis- 4. “Are you sure” appears on the tuner. Using the  
play, start the update program. “Finished”  
Tune Up/Down buttons, view the “Yes” and “No”  
appears on the computer screen when complete. selections.  
7. Cycle power to the tuner.  
5. Press BAND to select. A “No” selection  
returns to the top of the Factory Init menu. A  
“Yes” begins the initialization.  
6. “Please wait” appears on the tuner during the  
process and “Cycle Power” appears when com-  
plete.  
Factory Initialization (Chassis)  
The Factory Initialization procedure allows the  
erasure of all programmed settings and returns  
them to the factory default settings.  
7. Cycle power on the ST2-XM tuner.  
1. Enter the Setup Menu by pressing and holding  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
3. Press BAND.  
System Info (Chassis)  
4. Press BAND at “Build Time” to view.  
5. Press MEM Up/Down to advance.  
6. Press BAND at “Build Date” to view.  
7. Press MEM Up/Down to advance.  
8. Press BAND at “Version” to view.  
9. Press TNR SEL to exit the System Info menu.  
The System Info menu shows the ST2 Tuner’s  
manufacturing build properties.  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
2. TUNER SETUP appears. Press MEM Up/Down  
until SYSTEM INFO appears on the tuner.  
(END OF ST2 CHASSIS SETUP)  
Press TNR SEL  
button to select  
XM Tuner  
XM Setup Menu  
Memory Name Procedure  
TNR  
SEL  
TNR  
SEL  
TUNER  
SETUP  
Menu  
SOURCE  
NUM  
Procedure  
Chassis  
Setup  
Menu  
UPDATE  
FIRMW  
Procedure  
FACTORY  
INIT  
Procedure  
SYSTEM  
INFO  
Procedure  
TNR  
SEL  
SYSTEM  
INFO  
Procedure  
XM  
Setup  
Menu  
MEM  
NAME  
Procedure  
BANK  
NAME  
Procedure  
CONTROLLR  
ID  
Procedure  
DIAGNOSTICS  
Procedure  
FACTORY  
INIT  
Procedure  
TNR  
SEL  
SAVE  
CHANGES?  
MEMORY  
NAME  
BANK #  
MEMORY #  
Selects  
character  
Selects  
character  
position  
Repeat  
for each  
character  
in name  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
Tuner Setup Menu for XM  
It is important to select the desired tuner  
(Tuner 1 for XM) using the TNR SEL button  
BEFORE accessing the Tuner Setup Menus.  
2. TUNER SETUP appears. Press BAND again.  
3. MEMORY NAME appears on the tuner.  
4. Press BAND.  
5. Bank # appears.  
Memory Name (XM)  
6. Press the Tune Up/Down buttons to select the  
A memory preset must be created and saved  
before it can be named (see page 19). Once it is  
saved, the preset’s Tuner #, Bank # and Memory  
# must be entered in the following procedure.  
Bank #.  
7. Press BAND to advance. Memory # appears.  
8. Press the Tune Up/Down buttons to select a  
Memory #.  
(continued)  
Press TNR SEL  
button to select  
XM Tuner  
XM Setup Menu  
Bank Name Procedure  
TNR  
SEL  
TNR  
SEL  
TUNER  
SETUP  
Menu  
SOURCE  
NUM  
Procedure  
Chassis  
Setup  
Menu  
UPDATE  
FIRMW  
Procedure  
FACTORY  
INIT  
Procedure  
SYSTEM  
INFO  
Procedure  
TNR  
SEL  
SYSTEM  
INFO  
Procedure  
XM  
Setup  
Menu  
MEM  
NAME  
Procedure  
BANK  
NAME  
Procedure  
CONTROLLR  
ID  
Procedure  
DIAGNOSTICS  
Procedure  
FACTORY  
INIT  
Procedure  
TNR  
SEL  
SAVE  
CHANGES?  
BANK  
NAME  
BANK #  
Selects  
character  
Selects  
character  
position  
Repeat  
for each  
character  
in name  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
Name menu returns to the Bank # prompt to  
name other banks, or press TNR SEL to exit the  
Bank Name menu.  
Memory Name (XM) (continued)  
9. Press BAND to advance. MEMORY NAME  
appears again.  
10. Press BAND to access the Memory Name  
Controller ID (XM)  
The Controller ID procedure is used to identify  
the controller(s) that the XM tuner will  
respond to.  
entry screen.  
11. Press Tune Up/Down to select a character  
and MEM Up/Down to change a character  
position. Up to 12 characters can be entered  
one by one. A blinking cursor indicates the place- Note: For the XM module that is installed in the  
ment of the character being entered. ST2-XM chassis, “All Controllers” will be the  
12. Press BAND when memory name is entered. default setting.  
13. SAVE CHANGES will appear.  
14. Press Tune Up/Down to select Yes or No.  
Diagnostics (XM)  
15. Press BAND to save memory name. The  
Memory Name menu returns to the Memory #  
prompt to name other presets, or press TNR  
SEL to return to the Memory Name menu start.  
The Diagnostics procedure is for factory  
use only.  
Factory Initialization (XM)  
The Factory Initialization procedure allows the  
erasure of all programmed settings of the XM  
tuner and returns them to the factory default set-  
tings.  
Bank Name (XM)  
A custom name can be assigned to each of the  
six banks of Tuner 1 (XM).  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
2. TUNER SETUP appears. Press BAND.  
3. MEMORY NAME appears. Press MEM  
Up/Down until BANK NAME appears on the tuner.  
4. Press BAND.  
5. Bank # appears.  
6. Press the Tune Up/Down buttons to select the  
Bank #.  
7. Press BAND. BANK NAME appears again.  
8. Press BAND to access the Bank Name entry  
screen.  
9. Press Tune Up/Down to select a character  
and MEM Up/Down to change a character posi-  
tion. Up to 12 characters can be entered one by  
one. A blinking cursor indicates the placement of  
the character being entered.  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
2. TUNER SETUP appears. Press BAND.  
3. MEMORY NAME appears. Press MEM  
Up/Down until FACTORY INIT appears on the  
tuner.  
4. Press BAND to enter the FACTORY INIT menu.  
5. “Are you sure” appears on the tuner. Using the  
Tune Up/Down buttons, view the “Yes” and “No”  
selections.  
6. Press BAND to select. A “No” selection  
returns to the top of the Factory Init menu. A  
“Yes” begins the initialization.  
7. “Please wait” appears on the tuner during the  
process and “Cycle Power” appears when com-  
plete.  
10. Press BAND when bank name is entered.  
11. SAVE CHANGES will appear.  
8. Cycle power on the ST2-XM tuner.  
12. Press Tune Up/Down to select Yes or No.  
13. Press BAND to save bank name. The Bank  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
(END OF XM TUNER SETUP)  
System Info (XM)  
The System Info menu shows the ST2 Tuner’s  
manufacturing build properties.  
Tuner Setup Menu for AM/FM  
1. Enter the Setup Menu by pressing and holding It is important to select the desired tuner  
the TNR SEL button.  
(Tuner 2 for AM/FM) using the TNR SEL  
button BEFORE accessing the Tuner Setup  
Menus.  
2. TUNER SETUP appears. Press MEM Up/Down  
until SYSTEM INFO appears on the tuner.  
3. Press BAND.  
4. Press BAND at “Build Time” to view.  
5. Press MEM Up/Down to advance.  
6. Press BAND at “Build Date” to view.  
7. Press MEM Up/Down to advance.  
8. Press BAND at “Version” to view.  
9. Press TNR SEL to exit the System Info menu.  
Memory Name (AM/FM)  
A memory preset must be created and saved  
before it can be named (see page 19). Once it is  
saved, the preset’s Tuner #, Bank # and Memory  
# must be entered in the following procedure.  
(continued)  
XM Setup Menu  
Controller, Diagnostics, Factory Initialization  
and System Info Procedures  
Press TNR SEL  
button to select  
XM Tuner  
TNR  
SEL  
TNR  
SEL  
TUNER  
SETUP  
Menu  
SOURCE  
NUM  
Procedure  
Chassis  
Setup  
Menu  
UPDATE  
FIRMW  
Procedure  
FACTORY  
INIT  
Procedure  
SYSTEM  
INFO  
Procedure  
TNR  
SEL  
SYSTEM  
INFO  
Procedure  
MEM  
NAME  
Procedure  
BANK  
NAME  
Procedure  
CONTROLLR  
ID  
Procedure  
DIAGNOSTICS  
Procedure  
FACTORY  
INIT  
Procedure  
XM  
Setup  
Menu  
TNR  
SEL  
All Contrlrs  
This  
Procedure  
is for  
Factory  
use  
This  
Procedure  
returns the  
ST2 Tuner  
to its  
ONLY  
Factory  
settings  
Are you  
sure?  
Yes or No  
YES  
NO  
Please  
Wait  
Cycle Power  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
7. Press BAND. BANK NAME appears again.  
8. Press BAND to access the Bank Name entry  
screen.  
9. Press Tune Up/Down to select a character  
and MEM Up/Down to change a character posi-  
tion. Up to 12 characters can be entered one by  
one. A blinking cursor indicates the placement of  
the character being entered.  
10. Press BAND when bank name is entered.  
11. SAVE CHANGES will appear.  
12. Press Tune Up/Down to select Yes or No.  
13. Press BAND to save bank name. The Bank  
Name menu returns to the Bank # prompt to  
name other banks, or press TNR SEL to exit the  
Bank Name menu.  
Memory Name (AM/FM) (continued)  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
2. TUNER SETUP appears. Press BAND again.  
3. MEMORY NAME appears on the tuner.  
4. Press BAND.  
5. Bank # appears.  
6. Press the Tune Up/Down buttons to select the  
Bank #.  
7. Press BAND to advance.  
8. Press the Tune Up/Down buttons to select a  
Memory #.  
9. Press BAND to advance. MEMORY NAME  
appears again.  
10. Press BAND to access the Memory Name  
entry screen.  
11. Press Tune Up/Down to select a character  
and MEM Up/Down to change a character posi-  
tion. Up to 12 characters can be entered one by  
one. A blinking cursor indicates the placement of  
the character being entered.  
12. Press BAND when memory name is entered.  
13. SAVE CHANGES will appear.  
14. Press Tune Up/Down to select Yes or No.  
15. Press BAND to save memory name. The  
Memory Name menu returns to the Memory #  
prompt to name other presets, or press TNR  
SEL to return to the Memory Name menu start.  
Region (AM/FM)  
The Region procedure assigns either US or Euro  
to the tuner. The difference between the two is  
that US FM frequencies operate in .2 MHz incre-  
ments, while European FM frequencies operate in  
.05 MHz increments.  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
2. TUNER SETUP appears. Press BAND.  
3. MEMORY NAME appears. Press MEM  
Up/Down until REGION appears on the tuner.  
4. Press BAND.  
5. Press the Tune Up/Down buttons to select  
either US or EURO.  
Bank Name (AM/FM)  
A custom name can be assigned to each of the  
six banks of Tuner 2 (AM/FM).  
6. Press BAND to select. Press TNR SEL to exit  
the REGION menu.  
1. Enter the Setup Menu by pressing and holding  
the TNR SEL button.  
(END OF AM/FM TUNER SETUP)  
2. TUNER SETUP appears. Press BAND.  
3. MEMORY NAME appears. Press MEM  
Up/Down until BANK NAME appears on the tuner.  
4. Press BAND.  
5. Bank # appears.  
6. Press the Tune Up/Down buttons to select the  
Bank #.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
ST2 TUNER SETUP MENU  
The backup and restore PC application “RNET  
Backup” is available through the Document  
Center at www.russound.com. Also required are  
a DB9 male-to-female cable and laptop or desk-  
top PC.  
Backup and Restore  
Once all of the tuner settings are completed, it  
may be advisable to create a backup of the pro-  
grammed settings for future use. The backup will  
then be available in case tuner settings need to  
be restored.  
Press TNR SEL  
button to select  
AM/FM Tuner  
AM/FM Setup Menu  
TNR  
SEL  
TNR  
SEL  
Chassis  
Setup  
Menu  
SYSTEM  
INFO  
Procedure  
TUNER  
SETUP  
Menu  
SOURCE  
NUM  
Procedure  
UPDATE  
FIRMW  
Procedure  
FACTORY  
INIT  
Procedure  
TNR  
SEL  
REGION  
Procedure  
MEM  
NAME  
Procedure  
AM/FM  
Setup  
Menu  
BANK  
NAME  
Procedure  
TNR  
SEL  
TNR  
SEL  
MEMORY  
NAME  
BANK #  
MEMORY #  
SAVE  
CHANGES?  
BANK  
NAME  
BANK #  
Selects  
character  
Selects  
character  
Selects  
character  
position  
Selects  
character  
position  
Repeat  
for each  
character  
in name  
Repeat  
for each  
character  
in name  
SAVE  
CHANGES?  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ST2-XM TUNER PROGRAMMING  
PROGRAMMING FOR CAV6.6 USE  
NOTE: The CAV6.6 firmware must be version 2.00.01 or higher and UNO-S2  
firmware must be version 3.00.01 or higher to control the ST2-XM Tuner. Use  
the System Info Menu of the CAV6.6 to check the firmware version. If the  
firmware is not the proper revision as noted here, visit the Document Center  
at www.russound.com to obtain the latest version.  
To Program the CAV6.6 to operate with the ST2-XM Tuner:  
(refer to the CAV6.6 Instruction Manual for details)  
1. Enter the Setup Menu by pressing the Setup button on the side of the UNO-S2 keypad.  
2. SOURCE SETUP will appear. Enter the Source Setup Menu by pressing the Play button on the  
UNO-S2 keypad.  
3. BASIC SETUP will appear. Enter the Basic Setup Menu by pressing the Play button again.  
4. SOURCE NUM will appear. Use + and - buttons to select the source number to which Tuner 1 (XM)  
is connected. Press the Play button to enter your choice.  
5. SOURCE NAME will appear. Use + and - buttons to select the name for the source (e.g., Tuner 1  
or XM). Press the Play button to enter your choice.  
6. COMMAND TYPE will appear. Select PERIPHERAL from the list. Press the Play button to enter this  
choice.  
7. SAVE CHANGES? appears. Select “Yes” and press the Play button to save changes.  
8. SOURCE NUM appears again. Repeat steps 4 through 7 to configure the second tuner.  
9. Press the Setup button three times to back out of the Installation Menu.  
Source Configuration Note:  
When the ST2-XM Tuner is used with the CAV6.6 or other RNET controller, it is configured as an  
RNET command type “Peripheral” and is connected via the RNET bus. This makes the tuner behave  
as a fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique  
source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus.  
Key Function Note:  
When using the tuner with the CAV6.6-S2 system, do not reassign keypad and remote buttons for  
tuner control in the CAV6.6 Key Configuration Menu. When the tuner is assigned the “Peripheral” com-  
mand type in the CAV6.6 Setup Menu, key assignments and functions are automatically assigned and  
will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TECHNICAL SPECIFICATION  
ST2-XM Smart Tuner  
Dimensions: 17"W x 8"D x 1.8"H (43 x 20.3 x 4.4 cm)  
Weight: 7 lbs. (3.2kg)  
Power Supply: 12VDC 1.5A  
Frequency Range: AM 530 - 1710 kHz  
FM 87.7 - 107.9 MHz  
FM Antenna impedance: 75 ohm unbalanced  
Impedance: 300 ohm balanced  
AM  
Sensitivity @ S/N: 20dB 55 dBu  
Image rejection: 33dB  
S/N ratio: 45 dB  
FM  
Sensitivity @ S/N: 30 dB 6dB max 12 dBu  
Image rejection: 80 dB  
S/N ratio: 60 dB  
XM  
XM Band: 2332.5 - 2345 MHz  
XM Antenna: 50-ohm SMB connection  
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology  
incorporated in receivers compatible with the XM Satellite Radio system. Furthermore, the AMBE®  
voice compression software included in this product is protected by intellectual property rights  
including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of this  
or any other software contained in an XM radio is explicitly prohibited from attempting to copy,  
decompile, reverse engineer, or disassemble the object code, or in any way convert the object code  
into human-readable form. The software is licensed solely for use within this product.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY & REPAIR  
The Russound ST2-XM is fully guaranteed against all defects in materials and workmanship for two  
(2) years from the date of purchase. During this period, Russound will replace any defective parts and  
correct any defect in workmanship without charge for either parts or labor.  
For this warranty to apply, the unit must be installed and used according to its written instructions. If  
service is necessary, it must be performed by Russound. The unit must be returned to Russound at  
the owner's expense and with prior written permission. Accidental damage and shipping damage are  
not considered defects, nor is damage resulting from abuse or from servicing by an agency or per-  
son not specifically authorized in writing by Russound.  
This Warranty does not cover:  
Damage caused by abuse, accident, misuse, negligence,  
or improper installation or operation  
Power surges and lightning strikes  
Normal wear and maintenance  
Products that have been altered or modified  
Any product whose identifying number, decal, serial number, etc.  
has been altered, defaced or removed  
Russound sells products only through authorized Dealers and Distributors to ensure that customers  
obtain proper support and service. Any Russound product purchased from an unauthorized dealer or  
other source, including retailers, mail order sellers and online sellers will not be honored or serviced  
under existing Russound warranty policy. Any sale of products by an unauthorized source or other  
manner not authorized by Russound shall void the warranty on the applicable product.  
Damage to or destruction of components due to application of excessive power voids the warranty on  
those parts. In these cases, repairs will be made on the basis of the retail value of the parts and  
labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with  
a note explaining the nature of service required. Be sure to pack the unit in a corrugated container  
with at least three (3) inches of resilient material to protect the unit from damage in transit.  
Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number.  
Write this number on the shipping label and ship to:  
Russound  
ATTN: Service  
5 Forbes Road  
Newmarket, NH 03857  
Due to continual efforts to improve product quality as new technology and techniques become avail-  
able, Russound/FMP, Inc. reserves the right to revise system specifications without notice.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Russound  
5 Forbes Road, Newmarket, NH 03857  
tel 603.659.5170 • fax 603.659.5388  
e-mail: tech@russound.com  
28-1160  
07/13/04  
Copyright © 2004 Russound® All rights reserved.  
All trademarks are property of their respective owners.  
E. & O.E.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

RCA CRT Television 27F522T User Guide
RCA Stereo System 5643738A User Guide
Remington Electric Shaver R 91 User Guide
Roland Musical Instrument E 09 User Guide
Roper Range FGS326R User Guide
Russell Hobbs Appliance Trim Kit RHSLDW1B User Guide
Salton Hot Beverage Maker MEK15 User Guide
Samsung Camcorder HMX M20BN User Guide
Sears Paint Sprayer 486245332 User Guide
Sears Sewing Machine 385 1254180 User Guide