®
Model No. RBTL11104.1
Serial No.
USER'S MANUAL
Write the serial number in the space
above for future reference.
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT DI-
RECTLY.
CALL TOLL-FREE:
1-877-994-4999
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this man-
ual for future reference.
®
new products, prizes,
fitness tips, and much more!
®
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
11. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
2. Use the treadmill only as described in this
manual.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Keep the power cord and the surge suppres-
sor away from heated surfaces.
13. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
5. Do not operate the treadmill where aerosol
products are used or oxygen is administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 400 pounds. Never allow
more than one person on the treadmill at a time.
16. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
8. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes. Never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the circuit breaker.)
9. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
10. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local REEBOK dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
23. Inspect and properly tighten all parts of the
treadmill every three months.
24. Never drop or insert any object into any open-
ing.
25.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
21. When using iFIT.com CDs and videos, you can
manually override the speed and incline set-
tings at any time by pressing the speed and in-
cline buttons. However, when the next “chirp”
is heard, the speed and/or incline will change
to the next settings of the CD or video program.
22. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
26. The treadmill is intended for in-home use
only. Do not use the treadmill in any
commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill. If a decal is missing,
or if it is not legible, please call the toll-free telephone number on the front cover
of this manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for purchasing the REEBOK® 5500C
treadmill. The 5500C treadmill offers an impressive
array of features to help you achieve your fitness goals
in the convenience of your home. From the advanced
console to the cushioned walking platform, the 5500C
treadmill is designed to make each workout more ef-
fective and enjoyable. And when you’re not exercising,
the treadmill can be folded away, taking less than half
the floor space of conventional treadmills.
manual. To help us assist you, note the product model
number and serial number before calling. The model
number of the treadmill is RBTL11104.1. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Book Holder
Tray
Fan
Console
Key/Clip
Handrail
Handgrip Pulse Sensor
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Adjustable Cushioned
Walking Platform
(See page 24)
RIGHT SIDE
BACK
Rear Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until the treadmill is assembled.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt, the sides of the walking platform, or
the shipping carton. This does not affect treadmill performance. If there is lubricant on top of the walking belt or
on the sides of the walking platform, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires a phillips screwdriver
and the included allen wrench
.
1. With the help of a second person, carefully raise the
Uprights (65) to a vertical position.
1
Console
Assembly
Have the second person hold the console assembly near
the Uprights (65) as shown. Look under the console as-
sembly and locate the Console Wire Harness (71).
Cut the plastic ties securing the Upright Wire Harness
(85) to the right Upright (65). Connect the Upright Wire
Harness to the Console Wire Harness (71). Make sure to
connect the connectors properly (see the inset draw-
ing). The connectors should slide together easily and
snap into place. If the connectors do not slide together
easily and snap into place, turn one connector and try
again. IF THE CONNECTORS ARE NOT CONNECTED
PROPERLY, THE CONSOLE MAY BE DAMAGED
WHEN THE POWER IS TURNED ON.
71
85
65
71
85
2. Insert the excess Wire Harnesses (71, 85) into the right
Upright (65).
2
Console
Assembly
Set the console assembly on the Uprights (65). While a
second person holds the console assembly, attach the
console assembly with four Console Bolts (133) and four
Console Washers (69) as shown. Firmly tighten the
Console Bolts.
71, 85
69
69
133
133
65
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. With the help of a second person, raise the treadmill
Frame (55). Hold the Latch Housing (68) and the Latch
Housing Cover (5) against the sides of the Frame as
shown. Loosely thread the two blunt-tipped 1/2” Screws
(132) into the Latch Housing Cover and the Latch Housing
as shown. Do not tighten the Screws yet.
3
Hole
Knob
132
Remove the knob from the pin. Make sure that the collar
and the spring are on the pin. The collar should be on the
side of the spring shown. Insert the pin into the Latch
Housing (68), and tighten the knob back onto it.
87
49
5
68
Small
Holes
Align the pin with the hole in the Left Handgrip (87) by slid-
ing the Latch Housing (68) up or down. Make sure that the
pin can be inserted fully into the hole. Hold the Latch
Housing in place as you tighten two 1/2” Tek Screws (49)
into the Latch Housing and the Frame (55). Then, tighten
the 1/2” Screws (132). Note: It may be necessary to pull
on the knob to access and tighten the Screws.
Collar
55
Spring
132
Pin
49
4. Remove the backing from the indicated tape on the con-
sole assembly. Press the Book Holder (50) firmly onto the
tape. Note: The Book Holder may be preassembled.
4
50
Console
Assembly
Tape
5. Make sure that all parts are properly tightened before you use the treadmill. Place a mat beneath the
treadmill to protect the floor or carpet. Keep the included allen wrench in a secure place. The allen wrench
is used to adjust the walking belt (see pages 26 and 27).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
The chest pulse sensor consists of two components:
the chest strap and the sensor unit (see the drawing
below). Insert the tab on one end of the chest strap into
one end of the sensor unit, as shown in the inset draw-
ing. Press the end of the sensor unit under the buckle
on the chest strap. The tab should be flush with the
front of the sensor unit.
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° Fahrenheit (50°
Celsius) or below 14° Fahrenheit (-10° Celsius).
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Chest Strap
Tabs
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Tab
CHEST PULSE SENSOR TROUBLESHOOTING
Sensor
Unit
Buckle
Sensor Unit
The instructions on the following pages explain
how the chest pulse sensor is used with the con-
sole. If the chest pulse sensor does not function
properly, try the steps below.
Next, wrap the
chest pulse sen-
sor around your
chest and attach
the other end of
the chest strap to
the sensor unit.
Adjust the length
of the chest strap,
if necessary. The
chest pulse sen-
• Make sure that you are wearing the chest pulse sen-
sor as described at the left. Note: If the chest pulse
sensor does not function when positioned as de-
scribed, move it slightly lower or higher on your chest.
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, re-wet the electrode areas.
sor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens so-
lution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
• The CR2032 battery may need to be replaced (see
page 27).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TREADMILL OPERATION
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local REEBOK dealer or call the toll-free tele-
phone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If there are thin sheets of clear
plastic on the console, remove them.
Key
Clip
FEATURES OF THE CONSOLE
cable, you can connect the treadmill to your home
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer coaches you through every step of your work-
out. High-energy music provides added motivation. To
purchase iFIT.com CDs or videocassettes, call the
toll-free telephone number on the front cover of
The treadmill console offers an impressive array of
features designed to help you get the most from your
workouts.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
a touch of a button. As you exercise, the console will
display instant exercise feedback. You can even mea-
sure your heart rate using the handgrip pulse sensor or this manual.
the chest pulse sensor.
With the treadmill connected to your computer, you
The console also offers six personal trainer programs.
Each program automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive workout. Two heart rate programs are also offered.
Each program adjusts the speed and incline of the
treadmill to keep your heart rate near a target heart rate
while you exercise. You can even create custom pro-
grams and save them in memory for future workouts.
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a personal trainer
program, see page 13 To use a heart rate program,
see page 15. To create and use a custom program,
see pages 17 and 18. To use an iFIT.com CD or video
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a program, see page 21. To use an iFIT.com program
personal trainer in your home. Using the included audio directly from our Web site, see page 23.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
If the Start button or the
Speed increase button is
Note: To prevent damage to the walking platform,
always wear clean shoes when using the treadmill.
pressed, the walking belt
will begin to move at 1
mph. As you exercise,
Plug in the power cord (see
page 9). Next, locate the
change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph.
Reset
Position
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
reset position.
If one of the Quick Start buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in ei-
ther miles or kilometres. For simplicity, all in-
structions in this section refer to miles.
Stand on the foot rails of the treadmill. Find the clip at-
tached to the key (see the drawing on page 10) and
slide the clip onto the waistband of your clothes. Next,
route the cord attached to the clip under the handgrip
pulse sensor, and insert the key into the console.
After a moment, the displays and various indicators will
light. Test the clip by carefully taking a few steps
backward until the key is pulled from the console.
If the key is not pulled from the console, adjust the
position of the clip.
To stop the walking belt, press the Stop button.
The time will begin to flash in the Pace/Time dis-
play. To restart the walking belt, press the Start
button, the Speed increase button, or one of the
twelve Quick Start buttons.
Note: The first time the treadmill is used, observe
the alignment of the walking belt, and align the
walking belt if necessary (see page 27).
HOW TO USE THE MANUAL MODE
Change the incline of the treadmill as desired.
Insert the key into the console.
4
5
1
To change the incline of
the treadmill, press the
Incline increase and de-
crease buttons. Each
time a button is pressed,
the incline will change by
0.5%.
See HOW TO TURN ON THE POWER above.
Select the manual mode.
2
When the key is in-
serted, the manual
mode will be selected
and the indicator on the
Manual Control button
will light. If you have se-
Follow your progress with the matrix and the
displays.
lected a program, reselect the manual mode by
pressing the Manual Control button.
The matrix—When the
manual mode or the
iFIT.com mode is se-
lected, the matrix will
Start the walking belt.
3
display a 1/4-mile track.
As you exercise, the in-
dicators around the track
will light in succession until the entire track is lit.
The track will then darken and the indicators will
again begin to light in succession.
To start the walking belt, press the Start button,
the Speed increase button, or one of the twelve
Quick Start buttons.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Distance/Incline dis-
play—This display
shows the distance that
you have walked or run
Measure your heart rate if desired.
6
Note: If you use
the handgrip
and the incline level of
the treadmill. The display
will change from one number to the other every
few seconds. Note: Each time the incline changes,
the display will show the incline setting for several
seconds.
pulse sensor and
the chest pulse
sensor at the
same time, the
console will not
display your
Contacts
heart rate accu-
Calories/Pulse
display—This display
shows the approximate
number of calories you
rately. Before using the handgrip pulse sensor, re-
move the clear plastic film from the metal con-
tacts. In addition, make sure that your hands are
clean.
have burned. The dis-
play will also show your
To use the handgrip pulse sensor, first make sure
that your hands are clean. Next, stand on the
foot rails and hold the handgrip pulse sensor,
with your palms on the metal contacts. Avoid
moving your hands. When your pulse is detected,
two dashes (– –) will appear in the Calories/Pulse
display, and then your heart rate will be shown.
For the most accurate heart rate reading, con-
tinue to hold the contacts for about 15 sec-
onds.
heart rate when you use the handgrip pulse sen-
sor or the chest pulse sensor. The display will
change from one number to the other every few
seconds.
Speed display—This
display shows the
speed of the walking
belt.
Turn on the fan if desired.
7
8
Note: The console can
display speed and dis-
tance in either miles or
kilometres. To find which
unit of measurement is
selected, hold down the
Stop button while inserting the key into the con-
sole. An “E” for English miles or an “M” for metric
kilometres will appear in the Speed display. Press
the Speed increase button to change the unit of
measurement. When the desired unit of measure-
ment is selected, remove the key.
To turn on the fan, press the button below the fan.
To turn on the fan at high speed, press the button
a second time. To turn off the fan, press the but-
ton a third time. Note: A few minutes after the
walking belt is stopped, the fan will automatically
turn off.
When you are finished exercising, remove the
key from the console.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion or the treadmill will be damaged. Next, re-
move the key from the console and put it in a se-
cure place. Note: If the displays and various indi-
cators on the console remain lit after the key is
removed, the console is in the “demo” mode.
See page 24 and turn off the demo mode.
Pace/Time display—
When the manual mode
or the iFIT.com mode is
selected, this display will
show your current pace,
in minutes per mile, and
the elapsed time. The display will change from
one number to the other every few seconds.
When a program is selected (except for the Self
Select heart rate program), the display will show
the elapsed time and the time remaining in the pro-
gram.
When you are finished using the treadmill,
move the reset/off circuit breaker to the off po-
sition and unplug the power cord.
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The speed setting for the
first segment is shown in
the flashing Current
HOW TO USE PERSONAL TRAINER PROGRAMS
Current Segment
Segment column of the
matrix. (The incline set-
tings are not shown in
the matrix.) The speed
settings for the next
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
seven segments are
shown in the seven columns to the right.
Select one of the personal trainer programs.
2
To select a personal
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or in-
cline of the treadmill is about to change, the Speed
display and/or the Distance/Incline display will
flash to alert you. When the first segment ends, all
speed settings will move one column to the left.
The speed setting for the second segment will then
be shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment.
Note: If all of the indicators in the Current Segment
column are lit after the speed settings have moved
to the left, the speed settings may move downward
so that only the highest indicators appear in the
matrix. If some of the indicators in the Current
Segment column are not lit when the speed set-
tings move to the left again, the speed settings will
move back up.
trainer program, press
one of the Walk, Jog, or
Run buttons. The indi-
cator on the button that
you press will light.
When a personal trainer program is selected, the
Speed display will flash the maximum speed set-
ting of the program for a few seconds, and the
Distance/Incline display will flash the maximum in-
cline setting. The Pace/Time display will show
how long the program will last.
The matrix will show
the first seven speed
settings of the program.
Note: The diagrams on
the Walk, Jog, and Run
buttons show how the
speed and incline of
the treadmill will change during the personal
trainer programs. For example, the diagram on
the right Walk button shows that the speed and in-
cline will gradually increase during the first half of
the program and then gradually decrease during
the last half.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment col-
umn have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: When the next segment of the program
begins, the treadmill will automatically adjust
to the speed and incline settings for the next
segment.
Press the Start button or the Speed increase
button to start the program.
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. One speed setting and
one incline setting are programmed for each seg-
ment. Note: The same speed setting and/or in-
cline setting may be programmed for two or more
consecutive segments.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program at any time, press the Stop
button. The time will begin to flash in the
When you are finished exercising, remove the
key from the console.
7
Pace/Time display. To restart the program, press
the Start button or the Speed increase button. The
walking belt will begin to move at 1 mph. When the
next segment of the program begins, the treadmill
will automatically adjust to the speed and incline
settings for the next segment.
When the program has ended, make sure that
the incline of the treadmill is at the lowest set-
ting. Next, remove the key from the console and
put it in a secure place. Note: If the displays and
various indicators on the console remain lit
after the key is removed, the console is in the
“demo” mode. See page 24 and turn off the
demo mode.
Follow your progress with the displays.
See step 5 on page 11.
4
5
6
When you are finished using the treadmill,
move the reset/off circuit breaker to the off po-
sition and unplug the power cord.
Measure your heart rate if desired.
See step 6 on page 12.
Turn on the fan if desired.
See step 7 on page 12.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter your age.
HOW TO USE HEART RATE PROGRAMS
4
5
When a heart rate pro-
gram is selected, the
word “AGE” and the cur-
rent age setting will flash
in the Calories/Pulse
display. If you have al-
ready entered your age, simply press the Enter
button. If you have not entered your age, press
the increase and decrease buttons below the
Enter button to enter your age. Then, press the
Enter button.
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether
the medication will affect your exercise heart
rate.
Put on the chest pulse sensor.
Enter a maximum speed.
1
You must wear the chest pulse sensor (see
page 8) to use a heart rate program.
After you have entered
your age, the letters
“SPd” and the maximum
speed setting of the pro-
Insert the key into the console.
2
3
gram will flash in the
Speed display. If de-
sired, press the increase and decrease buttons
below the Enter button to adjust the maximum
speed setting. When the desired setting is shown,
press the Enter button.
See HOW TO TURN ON THE POWER on
page 11.
Select a heart rate program.
To select a heart rate
program, press the
85% Max or Self Select
button. The indicator on
the button that you
press will light.
If the 85% Max program is selected, go to step
7. If the Self Select program is selected, go to
step 6.
Enter a target heart rate.
6
7
During the 85% Max program, your heart rate will
reach approximately 85% of your estimated maxi-
mum heart rate; during the Self Select program,
your heart rate will remain near a level that you
select. Note: Your estimated maximum heart rate
is determined by subtracting your age from 220.
For example, if you are 30 years old, your esti-
mated maximum heart rate is 190 beats per
minute (220 – 30 = 190).
The letters “PLS” and
the target heart rate set-
ting for the program will
flash in the Calories/
Pulse display. If desired,
press the increase and
decrease buttons below the Enter button to adjust
the target heart rate setting. When the desired
setting is shown, press the Enter button.
During heart rate pro-
grams, the matrix will
show a moving graphic
that represents your
heart rate. Each time a
heartbeat is detected, a
peak will appear.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Each heart rate program is divided into several time
segments of different lengths. One target heart rate
is programmed for each segment. Note: If the Self
Select program is selected, the same target heart
rate is programmed for all segments.
the current target heart rate, the speed and/or in-
cline of the treadmill may automatically change to
bring your heart rate closer to the target heart rate.
If your pulse is not detected during the program,
the letters “PLS” will flash in the Calories/Pulse
display and the speed and incline of the treadmill
may automatically decrease until your pulse is de-
tected. If this occurs, see the instructions on page
8.
During each segment, the console will regularly
compare your heart rate to the current target heart
rate. If your heart rate is too far below or above
the target heart rate, a tone will sound and the
speed of the treadmill will automatically increase
or decrease to bring your heart rate closer to the
target heart rate. If the speed reaches the maxi-
mum speed setting of the program (see step 5 on
page 14) and your heart rate is still too far below
the current target heart rate, the incline of the
treadmill will also increase to bring your heart rate
closer to the target heart rate.
To stop the program at any time, press the Stop
button. Heart rate programs cannot be stopped
temporarily and then restarted. To use a heart rate
program again, reselect the program and start it at
the beginning.
Follow your progress with the displays.
See step 5 on page 11.
8
9
During the last three seconds of each segment, a
series of tones will sound and the Speed display
and the Distance/Incline display will flash.
Turn on the fan if desired.
See step 7 on page 12.
The program will continue until the last segment
ends. The walking belt will then slow to a stop.
When you are finished exercising, remove the
key from the console.
If the speed or incline setting is too high or too low
at any time during the program, you can adjust the
setting with the Speed or Incline buttons. However,
each time the console compares your heart rate to
10
See step 7 on page 14.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
in the matrix.) To program a speed setting and an
incline setting for the first segment, simply adjust
the speed and incline of the treadmill as desired
by pressing the Speed and Incline buttons. Every
few times one of the Speed buttons is pressed, an
additional indicator will light or darken in the
Current Segment column.
HOW TO CREATE CUSTOM PROGRAMS
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
11.
During the last three seconds of the first segment,
both the Current Segment column and the column
to the right will flash, a series of tones will sound,
and the Speed display and the Distance/Incline
display will flash. When the first segment ends, the
current speed setting and the current incline set-
ting will be saved in memory, and all speed set-
tings in the matrix will move one column to the left.
The speed setting for the second segment will
then be shown in the flashing Current Segment
column. Program a speed setting and an incline
setting for the second segment as described
above.
Select one of the custom programs.
2
To select a custom pro-
gram, press the Custom
Program 1 button or the
Custom Program 2 but-
ton. The indicator on the
button that you press will
light.
Press the Start button or the Speed increase
button and program the desired speed and in-
cline settings.
3
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
See the matrix. Each
custom program is di-
vided into one-minute
segments. One speed
setting and one incline
setting can be pro-
Current Segment
When the program is finished, remove the key.
4
grammed for each seg-
ment. The speed setting
for the first segment will
See step 7 on page 14.
be shown in the flashing Current Segment column
of the matrix. (The incline settings are not shown
17
Download from Www.Somanuals.com. All Manuals Search And Download.
column and the column to the right will flash, a se-
ries of tones will sound, the Speed display and the
Distance/Incline display will flash, and all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
HOW TO USE CUSTOM PROGRAMS
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on
page 11.
Select one of the custom programs.
2
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
To select a custom pro-
gram, press the Custom
Program 1 button or the
Custom Program 2 but-
ton. The indicator on
the button that you
If desired, you can change the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To in-
crease the length of the program, first wait until
the program ends. Then, press the Start button and
program speed and incline settings for as many ad-
ditional segments as desired. When you have
added as many segments as desired, press the
Stop button twice. To decrease the length of the
program, press the Stop button twice at any time
before the program ends.
press will light. When a custom program is se-
lected, the Speed display will flash the maximum
speed setting of the program for a few seconds,
and the Distance/Incline display will flash the max-
imum incline setting. The Pace/Time display will
show how long the program will last.
The matrix will show
the first seven speed
settings of the program.
To stop the program at any time, press the Stop
button. The time will begin to flash in the
Press the Start button or the Speed increase
button to start the program.
3
Pace/Time display. To restart the program, press
the Start button or the Speed increase button. The
walking belt will begin to move at 1 mph. When the
next segment of the program begins, the treadmill
will automatically adjust to the speed and incline
settings for the next segment.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Follow your progress with the displays.
See step 5 on page 11.
Each custom program is
4
5
6
7
divided into several one-
minute segments. One
speed setting and one
incline setting are pro-
grammed for each seg-
ment. The speed setting
for the first segment is
shown in the flashing
Current Segment column of the matrix. (The in-
cline settings are not shown in the matrix.) The
speed settings for the next seven segments are
shown in the columns to the right.
Current Segment
Measure your heart rate if desired.
See step 6 on page 12.
Turn on the fan if desired.
See step 7 on page 12.
When you are finished exercising, remove the
key from the console.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
See step 7 on page 14.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
19 and 20 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 21 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home com-
puter. See page 20 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the LINE OUT
jack on your stereo.
B
PHONES
B
CD
3.5mm
Y-adapter
Audio
Cable
VCR
Amp
LINE OUT
Headphones/Speakers
RCA Y-adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 20.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on page
19. To purchase iFIT.com CDs or videocassettes,
call the toll-free telephone number on the front
cover of this manual.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
Insert the key into the console.
1
AUDIO OUT
RIGHT
LEFT
See HOW TO TURN ON THE POWER on page 11.
Select the iFIT.com mode.
Audio
Cable
2
Adapter
To use an iFIT.com CD
or video program, press
the iFIT.com button. The
indicator on the button
will light.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
Y-adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD into
your CD player. If you are using an iFIT.com video-
cassette, insert the videocassette into your VCR.
Press the PLAY button on your CD player or
VCR.
4
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the time is flashing in the
Pace/Time display, press the Start button or the
Speed increase button on the console. The tread-
mill will not respond to a CD or video program
while the Pace/Time display is flashing.
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
RCA Y-adapter
Adapter
Audio
Cable
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
Wire removed from
AUDIO OUT jack
21
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings by
pressing the Speed or Incline buttons on the con-
sole. However, when the next “chirp” is heard,
the speed and/or incline will change to the
next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the Pace/Time display. To restart the pro-
gram, press the Start button or the Speed in-
crease button. After a moment, the walking belt
will begin to move at 1 mph. When the next
“chirp” is heard, the speed and incline will
change to the next settings of the CD or video
program.
Follow your progress with the LED track and
the displays.
5
See step 5 on page 11.
Measure your heart rate if desired.
See step 6 on page 12.
6
7
8
When the CD or video program is completed, the
walking belt will stop and the time will begin to flash
in the Pace/Time display. Note: To use another
CD or video program, press the Stop button or re-
move the key and go to step 1 on page 21.
Turn on the fan if desired.
See step 7 on page 12.
When you are finished exercising, remove the
key from the console.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
See step 7 on page 14.
• Make sure that the indicator on the iFIT.com
button is lit and that the time is not flashing in
the Pace/Time display. If the Pace/Time dis-
play is flashing, press the Start button or the
Speed increase button on the console.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
programs directly from the internet. Additional options
information.
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 20. In
addition, you must have an internet connection and
an internet service provider. A list of specific system re-
quirements is found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings by
pressing the Speed or Incline buttons on the con-
sole. However, when the next “chirp” is heard,
the speed and/or incline will change to the next
settings of the program.
Follow the steps below to use a program from our
Web site.
Insert the key into the console.
To stop the walking belt at any time, press the
Stop button on the console. The time will begin to
flash in the Pace/Time display. To restart the pro-
gram, press the Start button or the Speed in-
crease button. After a moment, the walking belt
will begin to move at 1 mph. When the next
“chirp” is heard, the speed and incline will
change to the next settings of the program.
1
See HOW TO TURN ON THE POWER on page 11.
Select the iFIT.com mode.
2
To use an iFIT.com CD
or video program, press
the iFIT.com button.
The indicator on the but-
ton will light.
When the program ends, the walking belt will stop
and the time will begin to flash in the Pace/Time
display. Note: To use another program, press the
Stop button and go to step 5.
Go to your computer and start an internet
connection.
3
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the indicator on the iFIT.com button is
lit and that the Pace/Time display is not flash-
ing. In addition, make sure that the audio cable
is properly connected, that it is fully plugged in,
and that it is not wrapped around a power cord.
Start your web browser, if necessary, and go to
4
Follow the desired links on our Web site to se-
lect a program.
5
Read and follow the on-line instructions for using a
program.
Follow your progress with the LED track and
the displays.
8
9
Follow the on-line instructions to start the
program.
6
See step 5 on page 11.
When you start the program, an on-screen count-
down will begin.
When you are finished exercising, remove the
key from the console.
See step 7 on page 14.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
HOW TO ADJUST THE CUSHIONING SYSTEM
The console features an information mode that keeps
track of the total number of hours that the treadmill has
been operated and the total number of miles or kilome-
tres that the walking belt has moved. The information
mode also allows you to switch the console from miles
per hour to kilometres per hour. In addition, the infor-
mation mode allows you to turn on and turn off the
demo mode.
The treadmill fea-
tures a cushion-
ing system that
reduces the im-
pact as you walk
or run on the
treadmill. To in-
Adjustment
Knob
crease the firm-
ness of the walk-
ing platform, turn
the adjustment
knob counterclockwise. To decrease the firmness, turn
the knob clockwise. Note: The faster you run on the
treadmill, or the more you weigh, the firmer the
walking platform should be.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
The Distance/Incline display
will show the total number of
miles (or kilometres) that the
walking belt has moved.
The Pace/Time display will
show the total number of
hours the treadmill has been
used.
An “E” for English miles or
an “M” for metric kilometres
will appear in the Speed dis-
play. Press the Speed in-
crease button to change the
unit of measurement.
IMPORTANT: The Calories/Pulse display should be
blank. If a “d” appears in the display, the console is in
the “demo” mode. This mode is intended to be used
only when a treadmill is displayed in a store. When the
console is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will au-
tomatically light in a preset sequence, although the
buttons on the console will not operate. If a “d” appears
in the Calories/Pulse display when the information
mode is selected, press the Speed decrease button
so the display is blank.
To exit the information mode, remove the key.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
1
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be
permanently damaged. Next, unplug the power cord.
CAUTION: You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown at the right. To
decrease the possibility of injury, bend your legs and
keep your back straight. As you raise the treadmill,
make sure to lift with your legs rather than your back.
Raise the treadmill about halfway to the vertical position.
2. Hold the treadmill frame firmly with your left hand. Using
2
your right hand, pull the latch knob to the right and hold it.
Raise the treadmill until the pin on the latch knob is
aligned with the hole in the left handgrip. Then, release
the latch knob. Make sure that the latch knob is fully
released so that the pin is fully inserted into the hole
in the left handgrip.
Frame
Latch
Knob
Latch
Knob
Pin
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Handgrip
Pin
Handgrip
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
pin on the latch knob is fully inserted into the hole in the
left handgrip.
1. Hold the handgrips and place one foot against one of the
wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
Base
3. Place one foot against a wheel, and carefully lower the
treadmill until the base is resting in the storage position.
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. See drawing 2 above. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past the latch pin.
2. See drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.
CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
Reset
and then press the switch back in.
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker located on the treadmill frame near the power cord (see c.
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill performance
b
may decrease and the walking belt may be permanently
damaged. Remove the key and UNPLUG THE POWER
CORD. Using the included allen wrench, turn both rear
roller adjustment bolts counterclockwise 1/4 of a turn.
When the walking belt is properly tightened, you should
be able to lift the edges of the walking belt 3 to 4 inches
off the walking platform. Be careful to keep the walking
belt centered. Plug in the power cord, insert the key, and
run the treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
3–4”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key and
UNPLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the left bolt counterclock-
wise 1/2 of a turn. Be careful not to overtighten the walking
belt. Plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is
centered.
a
b. If the walking belt slips when walked on, first remove the
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key, and care-
fully walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
b
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Next, remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
(17) and the Magnet (12) on the left side of the Pulley (11).
Turn the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that the gap between the Magnet
and the Reed Switch is about 1/8”. If necessary, loosen
the indicated Screw (40), move the Reed Switch slightly,
and then retighten the Screw. Re-attach the hood and run
the treadmill for a few minutes to check for a correct speed
reading.
a
1/8”
40
11
12
17
Top
View
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROU-
BLESHOOTING on page 8.
b
b. If the chest pulse sensor still does not function properly, the battery
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Battery Cover
Battery
Cover
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Rubber
Gasket
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed or incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed or incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart rate
trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed or incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
WORKOUT GUIDELINES
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the highest number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
EXERCISE FREQUENCY
To measure your heart rate during exercise, use the
handgrip pulse sensor or the chest pulse sensor.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for en-
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of knees
and back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot to-
ward you and rest it against the inner thigh of your extended leg.
Reach toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times for each leg. Stretches: Hamstrings,
lower back and groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
5
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. RBTL11104.1
R0305A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
1
1
4
1
1
4
1
2
4
1
1
7
2
2
1
1
1
2
2
14
1
1
1
1
1
4
1
1
1
1
2
1
1
1
1
1
1
1
56
1
2
8
4
1
1
1
2
2
1
Foot Rail
Left Outside Housing
Audio Wire
Isolator
Latch Housing Cover
Platform
Walking Platform Screw
Walking Belt
Frame Pivot Bolt
Frame Pivot Washer
Front Wheel/Pulley
Magnet
Front Roller Nut/Front Wheel Nut
Spacer Insert
Frame Pivot Spacer
Reed Switch Clip
Reed Switch
Lift Frame
Foot Rail Insert
Gear Rack
Foot Rail Screw
Motor Belt
Pulse Receiver
Drive Motor
Transformer
Chest Pulse Strap
Hood Bracket
51*
52
53
54
55
56
57
58
59*
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
2
2
2
1
1
1
2
1
1
1
1
4
1
1
1
4
1
1
2
1
1
1
2
1
2
2
2
2
1
1
1
2
2
6
1
1
1
2
1
1
1
1
8
1
2
1
5
2
1
1
Cushion Assembly
Roller Adj. Washer
Rear Roller Adjustment Bolt
Left Rear Endcap
Frame
Allen Wrench
Rear Platform Screw
Rear Roller
Idler Assembly
Audio Wire Nut
Pulse Bar
Spring Nut
Idler Arm
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Idler Spring
Upright/Base
Belt Guide Screw
Console Frame
Latch Housing
Console Washer
Left Handgrip, Bottom
Console Wire Harness
iFIT.com Wire
Incline Pivot Bolt
Hood Cover
Spring
Spring Pad Screw
Front Wheel
Wheel Bolt
Pulley Nut
Ground Wire
Chest Pulse Sensor
Right Rear Endcap
Lift Motor Bolt
Motor Bolt
Outlet Bracket
Left Inside Housing
Right Inside Housing
Right Outside Housing
Controller
Controller Bracket
Motor Hood
3/4” Screw
Motor Belly Pan
Belt Guide
3/4” Tek Screw
Foot Screw
Console
Console Base
Fan
Spring Pad
Belly Pan Screw
Upright Wire Harness
Shock
Left Handgrip, Top
Upright Endcap
Filter Wire
Latch Warning Decal
Incline Motor
Right Handgrip, Top
Fan Screw
Right Handgrip, Bottom
Tie Holder
Tie
8” Cable Tie
Base Pad
Left Front Endcap
Right Front Endcap
Ground Screw
Rear Foot
1/2” Tek Screw
Book Holder
Idler Arm Bolt
Reset/Off Circuit Breaker
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118*
119
120
121
122
1
1
1
2
2
1
1
2
1
1
1
2
1
2
1
4
1
1
4
2
2
1
Pulse Wire
Power Cord
Power Cord Grommet
Warning Decal
Spring Plate
123
124
125
126
127
128
129
130
131
132
133
134
135
#
2
1
1
2
1
2
2
1
5
2
4
4
1
1
1
1
1
Cushion Adj. Rod
Incline Bracket
Incline Motor Bolt (Bottom)
Controller Screw
Key/Clip
Cushion Adj. Gear
Cushion Adj. Wheel
Cushion Adj. Knob
Cushion Adj. Screw
1/2” Screw
Console Bolt
Pulse Bar Screw
Access Door
8” Blue Wire, 2 F
4” Blue Wire, 2 F
Blue Wire, M/F
User’s Manual
Jack
iFIT.com Audio Cable
Rear Roller Star Washer
Pulley Washer
Idler Pulley
Pulley Spacer
Outlet Bracket Star Washer
Static Decal
Wheel Housing
Idler Pulley Bolt
Spring Washer
Console Back
Latch Assembly
Spring Bolt
Cushion Adj. Pin
Motor Bushing
Idler Arm Nylon Washer
#
#
#
* Includes all parts shown in the box
# These parts are not illustrated
Specifications are subject to change without notice
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER OF THE PRODUCT (RBTL11104.1)
• The NAME OF THE PRODUCT (REEBOK 5500C treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST on pages 30 and 31)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire REEBOK® 5500C (“Product”) is warranted to be free of all defects in material and work-
manship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the drive motor for twenty years after the
date of purchase. Parts and labor are covered for one year after the date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or com-
ponent, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized service
provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to use,
operate, and maintain as set out in your User’s Manual (“Manual”).
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discovery of
the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product. Remember
to do the periodic maintenance requirements specified in the Manual to assure proper operation and your continued satis-
faction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-877-994-4999 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before shipping,
always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack your
Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the product.
Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the service is covered
by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use
or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits,
loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states
do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not
apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or
fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow
limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 226398 R0305A
Printed in USA © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|