ArtNo.000-0021 Toledo logo
110 Induction
User Guide
&
Installation & Service Instructions
U109948 - 04
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.015-0301 - Introduction - Induction cooker
1. Before You Start...
Thank you for buying a Falcon cooker. It should give you
many years of trouble-free cooking if installed and operated
correctly. It is important that you read this section before you
start, particularly if you have not used an induction cooker
before.
Personal Safety
Important information for pacemaker and implanted
insulin pump users: The functions of this hob comply with
the applicable European standards on electromagnetic
interference. If you are fitted with a pacemaker or
implanted insulin pump and are concerned please consult
your doctor for medical advice.
This appliance is designed for domestic cooking
only. Using it for any other purpose could invalidate
any warranty or liability claim. In particular, the
oven should NOT be used for heating the kitchen
– besides invalidating claims this wastes fuel and
may overheat the control knobs.
When the hob is in use keep magnetic items, such as
credit and debit cards, floppy disk, calculators, etc.
away.
Accessible parts will become hot during use and will
retain heat even after you have stopped cooking.
Installation and Maintenance
Keep babies and children away from the cooker and
never wear loose-fitting or hanging clothes while
the appliance is in use.
In the UK the electrical installation should be in accordance
with BS 7671. Otherwise, all installations must be in
accordance with the relevant instructions in this booklet, with
the relevant national and local regulations, and with the local
electricity supply companies’requirements.
Always be certain that the controls are in the OFF
position when the oven is not in use, and before
attempting to clean the cooker.
Make sure that the cooker is wired in and switched on.
Take care when touching the marked cooking areas
of the hob.
The hob control display will flash for about 2 seconds
during first power setting – this is normal.
When the oven is on, DO NOT leave the oven door
Set the clock to ensure that all the ovens are functional
– see the relevant section in this manual.
open for longer than necessary, otherwise the
control knobs may become very hot.
The cooker should be serviced only by a qualified service
engineer, and only approved spare parts should be used.
Cooking high moisture content foods
can create a ‘steam burst’when the
oven door is opened. When opening
the oven stand well back and allow any
steam to disperse.
Always allow the cooker to cool and then switch it off at the
mains before cleaning or carrying out any maintenance work,
unless specified otherwise in this guide.
Peculiar Smells
When you first use your cooker it may give off a slight odour.
This should stop after a little use.
ArtNo.324-0001 Steam burs
Before using for the first time, make sure that all packing
materials have been removed and then, to dispel
manufacturing odours, turn the ovens to 200°C and run for an
hour.
Always keep combustible materials, e.g. curtains, and
flammable liquids a safe distance away from your cooker.
Before using the grill for the first time you should also turn on
the grill and run for 30 minutes with the grill pan in position,
pushed fully back, and the grill door open.
DO NOT spray aerosols in the vicinity of the cooker
while it is on.
Use dry oven gloves when applicable – using damp
Make sure the room is well ventilated to the outside air
(see ‘Ventilation’ below). People with respiratory or allergy
problems should vacate the area for this brief period.
gloves might result in steam burns when you touch
a hot surface. Do not use a towel or other bulky cloth
in place of a glove – it might catch fire if brought into
contact with a hot surface.
Ventilation
NEVER operate the cooker with wet hands.
The use of a cooking appliance results in the production
of heat and moisture in the room in which it is installed.
Therefore, ensure that the kitchen is well ventilated: keep
natural ventilation holes open or install a powered cooker
hood that vents outside. If you have several hotplates on, or
use the cooker for a long time, open a window or turn on an
extractor fan.
DO NOT use aluminium foil to cover shelves, linings
or the oven roof.
NEVER heat unopened food containers. Pressure
build up may make the containers burst and cause
injury.
DO NOT use unstable saucepans. Always ensure that
you position the handles away from the edge of the
hotplate.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure to use adequately sized pans with flat
bottoms that are large enough to cover the surface
of the hotplate heating area.
Should a crack appear in the surface, disconnect the
appliance immediately from the supply and arrange
for its repair.
Never leave the hotplate unattended at high heat settings.
Pans boiling over can cause smoking, and greasy spills may
catch on fire. Use a deep fat thermometer whenever possible
to prevent fat overheating beyond the smoking point.
Always LIFT pans off the hob. Sliding pans may cause marks
and scratches. Always turn the control to the OFF position
before removing a pan.
DO NOT place anything between the base of the pan and the
NEVER leave a chip pan unattended. Always heat fat
hob surface (e.g. asbestos mats, aluminium foil, Wok stand).
slowly, and watch as it heats. Deep fry pans should
Care should be taken that no water seeps into the appliance.
be only one third full of fat. Filling the pan too full
of fat can cause spill over when food is added. If you
use a combination of oils or fats in frying, stir them
together before heating, or as the fats melt.
Only certain types stainless steel, enamelled steel pans or cast
iron pans with enamelled bases are suitable for induction hob
cooking.
The ceramic surface should be washed after use to prevent it
from becoming scratched or dirty. However, you should clean
the hob with caution as some cleaners can produce noxious
fumes if applied to a hot surface.
Foods for frying should be as dry as possible. Frost on frozen
foods or moisture on fresh foods can cause hot fat to bubble
up and over the sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or medium high
temperatures. Never try to move a pan of hot fat, especially a
deep fat fryer. Wait until the fat is cool.
DO NOT use abrasive cleaners/pads, oven aerosols/pads
or stain removers on the surface.
Do not use the top of the flue (the slot along the back of
the cooker) for warming plates, dishes, drying tea towels or
softening butter.
We recommend that you avoid wiping any surface unit areas
until they have cooled and the indicator light has gone off.
Sugar spills are the exception to this (see ‘Cleaning your
Cooker’). After cleaning, use a dry cloth or paper towel to
remove any cleaning cream residue.
DO NOT use water on grease fires and never pick
up a flaming pan. Turn off the controls and then
smother a flaming pan on a surface unit by covering
the pan completely with a well-fitting lid or baking
tray. If available, use a multipurpose dry chemical or
foam-type fire extinguisher.
Cooker Care
As steam can condense to water droplets on the cool outer
trim of the oven, it may be necessary during cooking to wipe
away any moisture with a soft cloth. This will also help to
prevent soiling and discolouration of the oven exterior by
cooking vapours.
This appliance is heavy so take care when moving it.
Hob Care
DO NOT use the hob surface as a cutting board.
Cleaning
Do not leave utensils, foodstuffs or combustible items on
the hob when it is not is use (e.g. tea towels, frying pans
containing oil).
In the interests of hygiene and safety, the cooker should be
kept clean at all times as a build up in fats and other food
stuff could result in a fire.
DO NOT place plastic or aluminium foil, or plastic
containers, on the hob.
Clean only the parts listed in this guide.
Clean with caution. If a wet sponge or cloth is used to wipe
spills on a hot surface, be careful to avoid steam burns. Some
cleansers can produce noxious fumes if applied to a hot
surface.
DO NOT leave the hob zones switched on unless
being used for cooking.
NEVER allow anyone to climb or stand on the hob.
Do not stand or rest heavy objects on the hob. Although the
ceramic surface is very strong, a sharp blow or sharp falling
object (e.g. a salt cellar) might cause the surface to crack or
break.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.025-0009 - Overview - 110 induction - toledo
2. Cooker Overview
�
Fig.2-1
�
�
�
�
�
The 110 induction cooker (Fig.2-1) has the following features:
Fig.2-2
A. 5 induction cooking zones
B. A control panel
C. A grill
D. A conventional oven
E.
F.
A programmable fan oven
A storage drawer
0004 Correct pa
The Hob
Use only pans that are suitable for induction hobs. We
recommend stainless steel, enamelled steel pans or cast iron
pans with enamelled bases. Note that some stainless steel
pans are not suitable for use with an induction hob so please
check carefully before purchasing any cookware.
Fig.2-3
ArtNo.312-0005 Curved
bottomed pan ceramic
Pans made of copper, aluminium or ceramic are not suitable
for use on an induction hob. The kind of pan you use and the
quantity of food affects the setting required. Higher settings are
required for larger quantities of food.
Pots and pans should have thick, smooth, flat bottoms
(Fig.2-2). This ensures the maximum heat transfer from the
hob to the pan, making cooking quick and energy efficient.
Never use a round-bottomed wok, even with a stand.
The very best pans have bases that are very slightly curved
up when cold (Fig.2-3). If you hold a ruler across the bottom
you will see a small gap in the middle. When they heat up the
metal expands and lies flat on the cooking surface.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Make sure that the base of the pan is clean and dry to prevent
any residue burning onto the hob panel. This also helps
prevent scratches and deposits.
Fig.2-4
�����
�����
�����
Always use pans that are the same size as (or slightly larger
than) the areas marked on the hob. Using a lid will help the
contents boil more quickly.
Always take care before touching the surface, even
when the hob is turned off. It may be hotter than you
think!
The induction hob comprises of five cooking zones
containing induction elements with different ratings and
diameters (Fig.2-4) each with a pan detector and residual
heat indicator, and a hob control display.
�����
�����
Fig.2-5
The hob control display (Fig.2-5) informs you of the following
induction hob functions:
Pan detector
�
�
H
A
L
Residual heat indicator
Automatic heat-up
Child lock
� �
ArtNo.313-0003
110 Induction hob display
Pan Detector,
IMPORTANT: After use, switch off the hob element by its
�
control and DO NOT RELY on the pan detector.
If a cooking area is switched on and there is no pan in place
or if the pan is too small for the cooking area, then no heat
will be generated. The symbol [ ] will appear on the hob
control display; this is the “pan-missing symbol”. Place a pan
of the correct size on the cooking area and the [ ] symbol
will disappear and cooking can begin. After 10 minutes
without detecting a pan the cooking zone will switch off
automatically.
��������������������
������������
�������������
����������
���������
������
���
���
���
���
����������
�����������
Table 2-1 shows the minimum pan sizes recommended for
each cooking zone.
ArtNo.051-0002 - Min pan diameter
���
Table 2-1
Note: Using pans with a base diameter smaller than those
recommended will result in a power reduction.
Residual Heat Indicator, H
After use, a cooking zone will remain hot for a while as heat
dissipates. When a cooking zone is switched off the residual
heat indicator symbol [H ], will appear in the display. This
shows that the cooking zone temperature is above 60°C and
may still cause burns. Once the temperature has dropped to
below 60°C the [H ] will go out.
Automatic Heat-up, A
This function is available on all of the cooking areas. It
allows rapid heating up of the element to bring the selected
cooking zone up to temperature. Once the zone is at the
required cooking temperature the power level will reduce
automatically to the preset level.
The function is selected by turning the control knob to the
‘A’position. This can be selected by either turning the control
knob momentarily anti-clockwise from the zero position
or clockwise past the ‘9’until the symbol [A ] is shown on
the hob control display. Once the [A ] is displayed, turn the
control knob to the level of your choice (1 to 9). The pan will
4
Download from Www.Somanuals.com. All Manuals Search And Download.
heat up at 100% power for a specified time before the power
is reduced to the level selected.
����������������������
�����������
�����������������
When the Automatic Heat-up function is activated, the hob
control display will alternately flash between the [A ] setting
and the chosen power level.
�
�
�
�
�
�
�
����
����
����
����
����
����
����
Once the automatic heat-up time has ended the hob control
display will stop flashing and will display the chosen power
level.
The Automatic Heat-up function can be stopped by either
turning the control knob back to the ‘0’power setting or
turning the control knob to the ‘9’power setting.
�
����
ArtNo.051-0001 - Induction power levels
�
����
For your guidance Table 2-2 shows the time available at
100% power depending on the power level selected in the
Automatic Heat-up mode.
Table 2-2
Fig.2-6
Child Lock, L
To prevent the unwanted use by children, the hob can be
locked.
�
IMPORTANT: This can only be activated when all the
cooking zones are switched off.
To lock the hob, first turn on any of the hob controls on then
off – this will activate the hob display – then simultaneously
turn both rear outer induction controls anti-clockwise
(Fig.2-6) until [L] appears in the hob control display for all
cooking areas.
This will NOT affect the ovens or grill; they can still be used.
Fig.2-7
To unlock the hob, simultaneously turn both rear outer
induction controls anti-clockwise until the [L] symbol
disappears.
ArtNorwards
Boil Dry Function
This function identifies when the temperature of the pan rises
rapidly and works to maintain a safe level of pan temperature.
It should not interfere with normal cooking.
Please remember not to leave the hob unattended.
Care should be taken to not allow your cookware to
Fig.2-8
boil dry.
The Grill
ArtNo.240-0001 -
Toledo grill l
Before using the grill for the first time, turn on the grill
and run for 30 minutes with the grill pan in position,
pushed fully back and the grill door open. Make sure the
room is well ventilated to the outside air.
Remove the pan from the bottom of the grill compartment
(Fig.2-7).
The grill has two elements that allow either the whole area of
the pan to be heated or just the right-hand half.
Fig.2-9
Adjust the heat to suit by turning the knob. To heat the whole
grill, turn the knob clockwise (Fig.2-8).
To heat the right-hand half, turn the knob anti-clockwise. The
neon light by the grill control will come on.
ArtNo.331-0002 Grill pan high/low position
The grill trivet can be turned over to give two grilling
positions (Fig.2-9).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For best results, you should leave the grill pan in the grill
chamber and preheat the appropriate part(s) of the grill for
two minutes. The grill trivet can be removed and the food
placed on it while you are waiting for the grill to preheat.
Fig.2-10
Once the grill has preheated, slide the grill pan out again.
With the trivet back in place with the food on it, slide the grill
pan back onto the side supports. Ensure that it is pushed
right in.
Accessible parts may be hot when the grill is in use.
Young children should be kept away.
ArtNo.322-0002 Conventional oven
Do not leave the grill on for more than a few moments,
without the grill pan underneath it.
Fig.2-11
Never close the grill door when the grill is on.
The Ovens
The clock must be set to the time of day before the right-
hand oven will work. See the following section on ‘The
Clock’ for instructions on setting the time of day.
ArtNo.321-0002 Fan assisted oven
References to ‘left-hand’ and ‘right-hand’ ovens apply as viewed
from the front of the appliance.
Fig.2-12
The left-hand oven is a conventional oven, while the right-
hand oven is a fanned oven that can be timed.
ArtNo.240-0002 -
Toledo ontrol 1
The Left-Hand Oven
The left-hand conventional oven (Fig.2-10) is fitted with two
heating elements, one visible in the top of the oven and the
second under the oven base. Be careful to avoid touching
the top element and element deflector when placing or
removing items.
The Right-Hand Oven
This oven (Fig.2-11) circulates hot air continuously, which
means faster, more even cooking. The recommended cooking
temperatures for a fanned oven are generally lower than for a
non-fanned oven.
Fig.2-13
ArtNo.240-0003 -
Toledo oveol 2
Operating the Ovens
Turn the particular oven knob to the desired temperature
(Fig.2-12).
The oven indicator light will glow until the oven has reached
the temperature selected. It will then cycle on and off during
cooking (Fig.2-13).
When cooking foods with high water content, there may be
some steam visible at the grille at the rear of the hotplate.
This is perfectly normal.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Clock
Fig.2-14
Setting the time of day
The LCD clock is shown in (Fig 2-14). When the clock is first
connected the display flashes ( 0.00) and ( ) alternately.
Press and hold both the [] and [] buttons as shown in
Fig.2-15. While holding these buttons press either the (–) or
(+) until the correct time shows. Remember this is a 24-hour
clock. If you make a mistake or press the wrong button, turn
off the power supply for a minute or two and start again.
ArtNo.302-0002 - 6BC annotated
A B C D E F
A – Minute minder, B – ‘Cook’ time, C – ‘Stop’ time,
Setting the minute minder
D – Manual, E & F – Time setting buttons
Press and hold the minute minder () button (Fig.2-16). At
the same time press either the (–) or (+) until the time you
want to cook for is shown (Fig.2-17).
Fig.2-15
You can check time remaining by pressing () and cancel the
beeper by pressing ().
ArtNo.302-0001 - 6-button clock
To stop the right-hand oven automatically
Press and hold the Stop Time () button (Fig.2-18). While
holding the () button press either the (–) or (+) until the
required ‘stop time’ shows. AUTO will show in the display.
Fig.2-16
Fig.2-17
Fig.2-18
Fig.2-19
Fig.2-20
Once the ‘stop time’ is reached, the beeper sounds. Turn the
oven control knob to 0 first, and then press () once to stop
the beep, press () again to return to manual cooking.
ArtNo.302-0003 - 6BC
mnute mindesetting 1
To start and stop the right-hand oven
automatically
Before you set the clock, you must have two numbers clearly
in mind.
The ‘cook period’, which is the period of time you want the
oven to cook.
ArtNo.302-004 -
Minute minder setting 2
The ‘stop time’, which is the time of day you want the oven to
stop cooking.
You cannot set a start time directly – this is set automatically
by setting the cooking period and stop time.
Press and hold the () button (Fig.2-19). While holding the
() button, press either (–) or (+) button until the required
‘cook period’ shows.
ArtNo.302-0005 -
6BC Stopping the oven 1
Then press and hold the () button (Fig.2-20). While
holding the () button, press either (–) or (+) button until the
required ‘stop time’ shows.
AUTO will now show in the display.
Set the oven to the required temperature. When cooking is
finished the beeper will sound. Turn the oven knob to the OFF
position first, and then press the () button once to stop the
beep, and press it again to return to manual cooking.
ArtNo.302-0006 - 6BC
setting the cook time
If you are out, do not worry about the beeper going off, it
stops after a while. When you return, turn the oven knob to 0
first, and then press () twice, to return to manual cooking.
ArtNo.302-0007 -
Setting the stop time
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO is showing, you want to reset to manual
cooking
When cancelling an automatic setting, any cooking time
already set must be returned to ( 0.00) before you can return
to manual, by pressing the () button.
Fig.2-21
Fig.2-22
Fig.2-23
Fig.2-24
Fig.2-25
Fig.2-26
ArtNo.302-000-
Activating the key lock 1
Key Lock
When the key lock is activated, the left-hand oven can be
operated as usual but the right-hand oven is locked and will
not come on.
ArtNo.302-0009 - Activating
the key lock 2
To activate the key lock
Make sure that the clock is in manual mode and cancel any
active programs.
Hold the Minute Minder () and Cook time () buttons for
about 8 seconds. ‘On’will appear on the display (Fig.2-21).
Press the ‘+’button once. The key symbol () and ‘OF’will
show on the display (Fig.2-22). Let go of the buttons.
The right-hand oven functions are now locked. After a few
seconds the display will revert to show the time of day and
the key symbol (Fig.2-23).
ArtNo.302-000 -
Activating the key lock 3
To turn off the key lock
Hold the Minute Minder () and Cook time () buttons for
about 8 seconds. ‘OF’will appear on the display (Fig.2-24).
Press the ‘+’button once. The key symbol () goes out and ‘On’
shows on the display (Fig.2-25). Let go of the buttons.
ArtNo.302-0011 - 6BC
Deactivating the key lock 1
After a few seconds the display will revert to show the time of
day.
The right-hand oven can now be used normally.
ArtNo.302-0012 -
Deactivating the key lock 2
�
ArtNo.320-0009 Oven shelf
�
�
�
A - Top view, B - Side view, C - Shelf guard, D - Front
The shelf guard should be at the back pointing upwards
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
Fig.2-27
Oven Shelves
�
In addition to the flat shelves (Fig.2-26), some models are
supplied with a drop shelf (Fig.2-27). The drop shelf increases
the possibilities for oven shelf spacing.
ArtNo.320-0010 Flat & drop shelves
The oven shelves can be easily removed and refitted.
�
Pull the shelf forward until the back of the shelf is stopped by
the shelf stop bumps in the oven sides (Fig.2-28).
Lift up the front of the shelf so the back of the shelf will pass
under the shelf stop and then pull the shelf forward
(Fig.2-29).
A - Flat shelf, B - Drop shelf
To refit the shelf, line up the shelf with a groove in the oven
side and push the shelf back until the ends hit the shelf stop.
Lift up the front so the shelf ends clear the shelf stops, and
then lower the front so that the shelf is level and push it fully
back (Fig.2-30).
Fig.2-28
Fig.2-29
the shelf 1
ng the shelf 2
The Handyrack
The Handyrack (Fig.2-31) fits to the left-hand oven door
only. Food cooking on it is easy to attend to, because it is
accessible when the door is open.
Fig.2-30
The maximum weight that can be held by the Handyrack is
5.5kg (12lb). It should only be used with the supplied roasting
tin, which is designed to fit the Handyrack. Any other vessel
could be unstable.
Additional roasting tins are available from our cookware
collection – Part Code RM027.
It can be fitted at two different heights. One of the oven
shelves must be removed and the other positioned to suit.
When the Handyrack is used in its highest position, other
dishes can be cooked on the bottom shelf position or base of
the oven.
Fig.2-31
When the Handyrack is used in its lowest position, other
dishes can be cooked on the second shelf position or base of
the oven.
To fit the Handyrack, locate one side of it on the door bracket
(Fig.2-32).
Then spring the other side out to clip it onto the other
ArtNo.320-0014 Handyrack on LH door
bracket (Fig.2-33).
Fig.2-32
Fig.2-33
ANo.320-0015
Fitting the Handyack 1
ArtNo.320-0016
Fitting the handyrack 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Oven Light
Press the appropriate button to turn one of the lights on
Fig.2-34
(Fig.2-34).
If an oven light fails, turn off the power supply before
changing the bulb. See the ‘Troubleshooting’ section for
details on how to change the bulb.
ArtNo.320-0027
- Twin oven ligh
The Browning Element
The Browning Element is positioned in the top of the left-
hand oven. It can be used at the end of a normal cooking
period to give extra browning to au gratin dishes or give a
crisper finish to meat.
Fig.2-35
After the normal cooking is finished turn the left-hand
oven thermostat knob clockwise to the browning position,
indicated by () on the fascia panel.
Only the browning element will operate when the thermostat
is turned to this position. The top and base cooking elements
will automatically switch off.
ArtNo.340-0001 110 drawer position
Storage
Fig.2-36
The bottom drawer (Fig.2-35) is for storing oven trays and
other cooking utensils. It can get very warm, do not store
anything in it that may melt or catch fire. The drawer can be
removed completely by pulling it right out and up (Fig.2-36).
40-0002 110 removing the drawer
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.030-0002 - Cooking tips - electric
3. Cooking Tips
Tips on Cooking with the Timer
General Oven Tips
If you want to cook more than one dish, choose dishes that
require approximately the same cooking time. However,
dishes can be ‘slowed down’slightly by using small containers
and covering them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or placing them in
larger containers.
The wire shelves should always be pushed firmly to the back
of the oven.
Baking trays with food cooking on them should be placed level
with the front edge of the oven’s wire shelves. Other containers
should be placed centrally. Keep all trays and containers away
from the back of the oven, as overbrowning of the food may
occur.
Very perishable foods such as pork or fish should be avoided
if a long delay period is planned, especially in hot weather.
For even browning, the maximum recommended size of a
baking tray is 340mm (13½”) by 340mm (13½”).
DO NOT place warm food in the oven to be timed.
When the oven is on, do not leave the door open for
longer than necessary, otherwise the knobs may get very
hot.
DO NOT use a timed oven that is already warm.
DO NOT use the timed oven if the adjoining oven is
already warm.
•
Always leave a ‘fingers width’between dishes on the
same shelf. This allows the heat to circulate freely
around them.
Whole poultry must be thoroughly defrosted before being
placed in the oven. Check that meat and poultry are fully
cooked before serving.
•
To reduce fat splashing when you add vegetables to hot
fat around a roast, dry them thoroughly or brush lightly
with cooking oil.
•
•
Where dishes may boil and spill over during cooking,
place them on a baking tray.
The Cook & Clean oven liners (see ‘Cleaning Your Cooker’)
work better when fat splashes are avoided. Cover meat
when cooking.
•
•
Sufficient heat rises out of the oven while cooking to
warm plates in the grill compartment.
If you want to brown the base of a pastry dish, preheat
the baking tray for 15 minutes before placing the dish in
the centre of the tray.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.031-0002
4. Cooking Table
The oven control settings and cooking times given in the table below are intended to be used
AS A GUIDE ONLY. Individual tastes may require the temperature to be altered to provide a
preferred result.
Top
Centre
Base
Food is cooked at lower temperature in a fan oven than in a conventional oven. When using
recipes, reduce the fan oven temperature by 10°C and the cooking time by 5-10 minutes. The
temperature in the fanned oven does not vary with height in the oven so you can use any shelf.
Oven Shelf Positions
Conventional Oven
Fan Oven
Temperature Shelf Temperature
ArtNo.050-0003A - Cooking table - electric & fan
Food
Meat
°C
position
°C
Approximate cooking time
ArtNo.050-0001 Gas cooking table
Thoroughly thaw frozen joints before
cooking. Meat may be roasted at
220°C (210°C for fan oven) and the
cooking time adjusted accordingly.
For stuffed and rolled meats, add
approximately 10 minutes per 500g,
or cook at 200°C (190°C) for 20
minutes then 160°C (150°C) for the
remainder.
Beef (no bone)
160
200
160
200
160
200
C
C
C
C
C
C
150
190
150
190
150
190
30-35 minutes per 500g +30-35 minutes.
20-25 minutes per 500g +20-25 minutes.
30-35 minutes per 500g +30-35 minutes.
25-30 minutes per 500g +25-30 minutes.
35-40 minutes per 500g +35-40 minutes.
25-30 minutes per 500g +25-30 minutes.
Lamb
Pork
Poultry
Chicken
160
200
C
C
C
C
C
C
C
T
150
190
20-25 minutes per 500g +20-25 minutes.
15-20 minutes per 500g +15-20 minutes.
20 minutes per 500g +20 minutes.
15 minutes per 500g +15 minutes.
25-30 minutes per 500g.
For stuffed poultry, you could cook
at 200°C (190°C) for 20 minutes
then 160°C (150°C) for remainder.
Do not forget to include the weight
of the stuffing.
For fresh or frozen prepacked
poultry, follow instructions on the
pack. Thoroughly thaw frozen
poultry before cooking.
Turkey
Duck
160
150
200
190
160
150
200
190
20 minutes per 500g.
Casserole
Yorkshire pudding
Fish
140-150
220
130-140
210
2-4 hours according to recipe.
Large tins 30-35 minutes; individual 10-20 minutes.
Fillet
190
190
190
C/B
C/B
C/B
180
180
180
15-20 minutes.
Whole
15-20 minutes per 500g.
Steaks according to thickness.
Steak
Cake
Using the conventional oven: when
Very rich fruit - Christmas, 140
wedding, etc.
C/B
130
45-50 minutes per 500g of mixture.
two tier cooking leave at least one
runner space between shelves.
Position the baking tray with the
front edge along the front of the
oven shelf.
Fruit 180 mm tin
Fruit 230 mm tin
Madeira 180 mm
Queen cakes
Scones
150
150
160
190
220
C/B
C/B
C
140
140
150
180
210
2-2½ hours.
Up to 3½ hours.
80-90 minutes.
15-25 minutes.
10-15 minutes.
Up to three tiers can be cooked in a
fan oven at the same time but make
sure to leave at least one runner
space between each shelf being
cooked on.
C
C
Victoria sandwich
180 mm tin
180
180
C
C
170
170
20-30 minutes.
30-40 minutes.
210 mm tin
Desserts
Using the conventional oven: for
even browning the maximum size of
baking tray recommended is 340mm
x 340mm. This ensures free heat
circulation.
Shortcrust tarts
Fruit pies
200
200
C
C
190
190
20-30 minutes on a preheated tray.
35-45 minutes.
Tartlets
200
C
190
10-20 minutes according to size.
20-40 minutes according to size.
2-3 hours.
Puff pastry
230
C
220
If cooking a two tier load, the trays
should be interchanged
Meringues
100
C
90
Baked egg custard
Baked sponge pudding
Milk pudding
160
C
150
45-60 minutes.
approximately halfway though the
cooking time.
190
C
180
40-45 minutes.
140-150
220
C/B
C/T
130-140
210
2 to 3 hours.
Bread
20-30 minutes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.045-0011 - Cleaning - 110 Induction - tpl glzd & std grill
5. Cleaning Your Cooker
Isolate the electricity supply before carrying out any major
cleaning. Allow the cooker to cool.
Fig.5-1
Never use paint solvents, washing soda, caustic cleaners,
biological powders, bleach, chlorine based bleach
cleaners, coarse abrasives or salt. Do not mix different
cleaning products – they may react together with
hazardous results.
All parts of the cooker can be cleaned with hot soapy water
– but take care that no surplus water seeps into the
appliance.
We have developed a range of cleaning products that give
maximum performance without damaging the enamel and
painted surfaces, in particular a Ceramic Hob Cleaner set
with scraper. More information is available through either the
Cookware Collection brochure supplied with your cooker or our
Remember to switch the electricity supply back on and reset
the clock before reusing the cooker.
Hob
Daily Care
First of all make sure that all heat indicator lights are off and
that the cooking surface is cool. Apply a small dab of ceramic
cleaning cream in the centre of each area to be cleaned.
Dampen a clean paper towel and work the cream onto the
cooking surface. As a final step, wipe the cooking surface with
a clean, dry paper towel.
Cleaning Spills
For spills and boil-overs that occur while cooking, turn the
unit off and wipe the area surrounding the hot zone with a
clean paper towel. If a spill (other than a sugary substance) is
on the hot zone, do not clean until the unit has completely
cooled down, and then follow the instructions below
(‘Cleaning burned-on spills’).
If you accidentally melt anything on the surface, or if you spill
foods with a high sugar content (preserves, tomato sauce,
fruit juice, etc.), remove the spill IMMEDIATELY with a razor
scraper, while the unit is still hot.
IMPORTANT: Use an oven glove to protect your hand from
potential burns.
Scrape the major spill or melted material from the cooking
zone and push into a cold area. Then, turn the unit ‘OFF’and
allow it to cool before cleaning further. After the cooking
surface cools down and the heat indicator lights go off, follow
the ‘Daily Care’ procedure outlined above.
Cleaning Burned-on Spills
Make sure that the heat indicator lights are off and that the
hob is cool. Remove the excess burned-on substance with a
single-edged razor scraper. Hold the scraper at an angle of
about 30° to the surface and then scrape off the burned-on
matter (Fig.5-1).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Once you have removed as much as possible with the scraper,
follow the ‘Daily Care’ procedure outlined above.
Fig.5-2
To Remove Metal Rub-off
Sliding pans on the hob – especially aluminium or copper
pans – can leave marks on the surface. These marks often
appear like scratches, but can easily be removed using the
procedure described previously for ‘Cleaning spills’. If the
rub-off marks are especially stubborn, use a cleaning cream
together with the razor scraper, as described in ‘Cleaning
burned-on spills’.
Grill
The grill pan and grid should be washed in hot soapy water.
After grilling meats or any foods that soil, leave to soak for a
few minutes immediately after use. Stubborn particles may
be removed from the grid using a nylon brush. Alternatively,
the grill pan can be washed in a dishwasher.
Before you remove any of the grill parts for cleaning,
ensure that they are cool, or use oven gloves.
DO NOT use any abrasive substances.
Control Panel and Doors
Avoid using any abrasive cleaners, including cream cleaners,
on brushed stainless steel surfaces. For best results, use a
liquid detergent or our Multi-purpose Cleaner.
The same cleaner can also be used on the doors. Alternatively,
use a soft cloth wrung out in clean hot soapy water. You can
use the same method for cleaning the control panel and
knobs (although we do supply a specialist Fascia Cleaner).
After cleaning, polish with a dry cloth.
Ovens
The oven door front panels can be taken off so that the glass
panels can be cleaned. Move the cooker forward to gain
access to the sides (see the ‘Moving the Cooker’ section under
‘Installation’).
Door Panel
Open the oven door slightly and remove the front panel
fixing screws from the door sides, two each side (Fig.5-2).
Carefully lift off the outer door panel. The inside face of the
glass panels can now be cleaned – take care not to disturb or
wet the door insulation.
The door is triple glazed but the inner two panels are fixed
and should not be separated. After cleaning, carefully refit the
outer door panel and replace the side fixing screws.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
‘Cook & Clean’ Panels
Fig.5-3
The main oven has side ‘Cook & Clean’panels which have
been coated with a special enamel that partly cleans itself.
This does not stop all marks on the lining, but helps to reduce
the amount of manual cleaning needed.
These panels work better above 200°C. If you do most of your
cooking below this temperature, occasionally remove the
panels and wipe with a lint free cloth and hot soapy water.
The panels should then be dried and replaced and the oven
heated at 200°C for about one hour. This will ensure that the
panels are working effectively.
ArtNo.320-0025 - Oven roof -removing
Removing the Panels to clean the Enamel
Interior
Fig.5-4
If you wish to clean the enamel interior of the oven, you will
first need to remove the shelves.
On some models the main oven has a removable oven roof.
Slide the roof liner forwards and remove (Fig.5-3).
Each side of the oven is fixed with four fixing screws. You do
not have to remove the screws to remove the oven panels.
Simply lift each side panel upwards, slide them off the screws
and then pull them forwards (Fig.5-4).
ArtNo.320-0008 Removing the oven lining
Once the panels have been removed, the oven enamel
interior can be cleaned.
DO NOT use steel wool, oven cleaning pads, or any other
materials that will scratch the surface.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.055-0002 - Troubleshooting - Induction
6. Troubleshooting
The cooling fan
Interference with and repairs to the hob MUST NOT
The induction hob incorporates a cooling fan. This
cooling fan is active when either the grill or ovens
are on. Under certain conditions, the cooling fan may
remain active when the grill or ovens are switched off.
This is normal and the fan will switch off automatically.
be carried out by unqualified persons. Do not try
to repair the hob as this may result in injury and
damage to the hob. Please arrange for repair by a
suitably competent person.
Note: The induction hob is able to self-diagnose a
number of problems and can show this information to
the user via the hob control display. Error codes may be
displayed if your hob has developed a fault.
A crack has appeared in the hob surface
Disconnect the cooker immediately from the power
supply and arrange for its repair. Do not use the cooker
until after the repair.
If you appliance reports an error or is not working,
you may be able to correct the fault by consulting the
following.
My hob is scratched
Always use the cleaning methods recommended in this
guide, and ensure that the pan bottoms are smooth and
clean.
Error code E2 is displayed
The electronic unit is too hot. Please check the
installation of the cooker, making sure that there is
sufficient ventilation. I n extreme cases, if a cooking
utensil has been allowed to boil dry this error code
may also be displayed. If in doubt please contact your
installer or a qualified repair engineer.
Marks from mineral deposits from water or food can be
removed with a cleaning cream. However, tiny scratches
are not removable but will become less visible in time as
a result of cleaning.
The oven fan is noisy
No display operation
The note of the oven fan may change as the oven heats
up – this is perfectly normal.
Over voltage or loss of supply voltage to the cooker. If in
doubt please contact your installer or a qualified repair
engineer.
Grill not cooking properly
Are you using the pan and trivet supplied with the
cooker? Is the pan being used on the runners, not the
floor of the compartment? Is the grill tray pushed back
fully to the ‘back stop’position?
Error code ERxx or Ex is displayed
The appliance has developed an internal technical fault
that cannot be rectified by the user. Please contact your
installer or a qualified repair engineer.
The knobs get hot when I use the oven or grill. Can I avoid
this?
The fuse blows or the RCD trips regularly
Please contact your installer or a qualified repair
engineer.
Yes, this is caused by heat rising from the oven or the
grill, and heating them up. Do not leave the oven door
open. Make sure that the grill pan is pushed right back
to the ‘back stop’when grilling.
The hob will not switch on
Has the wiring system in the house blown a fuse or
tripped an RCD?
Always grill with the grill compartment door open.
Has the hob been correctly connected to the mains
supply?
If there is an installation problem and I don’t get my
original installer to come back to fix it, who pays?
You do. Service organisations will charge for their call-
outs if they are correcting work carried out by your
original installer. Therefore, it’s in your own interest to
keep track of this installer so that you can contact them
as required.
Has the child lock been activated? Please refer to the
child lock section for details of this function.
The induction hob is noisy
When using the induction hob there may be some
‘noise’emitted from the pan. This is normal and may be
most noticeable when cooking on high power settings
or if 5 pans are used simultaneously. The type of pan
may also contribute to induction ‘noise’.
Power failure
In the event of a failure in the electrical supply,
remember to reset the clock to ensure that the timed
oven continues to operate.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Food is cooking too slowly, too quickly, or burning
Before removing the existing bulb, turn off the power
supply and ensure that the oven is cool. Open the oven
door and remove the oven shelves.
Cooking times may differ from your previous
oven. Check that you are using the recommended
temperatures and shelf positions – see the oven
cooking guide. Then adjust the settings according to
your own individual tastes.
Locate the bulb cover and unscrew it by turning it
anticlockwise (it may be very stiff).
Now unscrew the existing bulb anticlockwise, taking
care to protect your fingers with a glove in case the bulb
should shatter.
The oven is not cooking evenly
Do not use a baking tray with dimensions larger than
those specified in the section on ‘General Oven Tips’.
Screw in the new bulb clockwise and then screw the
bulb cover back on. Turn on the electricity supply and
check that the bulb now lights.
If you are cooking a large item, be prepared to turn it
round during cooking.
If two shelves are used, check that space has been left
for the heat to circulate. When a baking tray is put into
the oven, ensure that it is placed centrally on the shelf.
Check that the door seal is not damaged and that the
door catch is adjusted so that the door is held firmly
against the seal.
A dish of water when placed on the shelf should be the
same depth all over. (For example, if it is deeper at the
back, then the back of the cooker should be raised up or
the front lowered.) If the cooker is not level, arrange for
your supplier to level it for you.
The timed oven is not coming on when turned on
manually
Is the power on? Is the clock illuminated? If not, there
may be something wrong with the power supply. Is the
cooker supply on at the isolator switch?
Has the time of day been set?
Is the key symbol ( ) showing in the display to signify
that the oven is locked? See the ‘Clock’ section of the
instructions for more information on the key lock
feature.
The timed oven is not coming on when automatic cooking
Has the oven knob been left in the OFF position by
mistake? Is the oven locked (see above)?
Oven temperature getting hotter as the cooker gets older
If turning the temperature down using the oven control
knob has not worked, or has only worked for a short
time, then you may need a new thermostat. This should
be fitted by a service person.
The Oven light is not working
The bulb has probably blown. You can buy a
replacement bulb (which is not covered under the
guarantee) from most electrical stores. Ask for an Edison
screw fitting 15W 240V lamp, FOR OVENS. It must be
a special bulb, heat resistant to 300°C. See the HELP
leaflet for spares by mail order.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.065-0002 - Installation - 110 Induction
7. Installation
Dear Installer
Before you start your installation, please complete the details
below, so that, if your customer has a problem relating to
your installation, they will be able to contact you easily.
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner but
NOT in a room containing a bath or shower.
This appliance is designed for domestic cooking only. Use for
any other purpose could invalidate any warranty or liability
claim.
����������������
You will need the following equipment to complete the
cooker installation satisfactorily:
•
•
Multimeter (for electrical checks)
�������������������
Cooker levelling tool with Allen keys (provided in pack)
You will also need the following tools:
1.
2.
Electric drill
Masonry drill bit (only required if fitting the cooker on a
stone or concrete floor)
����������������������������
3.
Wall plugs (only required if fitting the cooker on a stone
or concrete floor)
4.
5.
6.
7.
8.
9.
Steel tape measure
Cross-head screwdriver
Flat-bladed screwdriver
Spirit level
�����������������������
Pencil
Adjustable spanner
Safety Requirements
The cooker must be installed in a well-ventilated space, in
Checking the parts:
accordance with the section entitled ‘Electrical Connection’.
Levelling tool and Allen keys
Grill pan and trivet
Read these instructions before installing or using the
appliance.
ArtNo.000-0002 Classic tools
Provision of Ventilation
ArtNo.330-0001
This appliance is not connected to a combustion products
evacuation device. Therefore, particular attention must be
given to the relevant requirements regarding ventilation.
3 flat oven shelves and 1 drop
shelf
Handyrack
All rooms require a window that can be opened, or
equivalent, while some rooms require a permanent vent in
addition to the window.
ArtNo.324
ArtNo.324-0011 Flat & drop shelves
Roasting tin
Plinth
A
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Positioning the Cooker
Fig.7-1 shows the minimum recommended distance from the
Fig.7-1
cooker to nearby surfaces.
����
���
����
���
�����
���
The cooker should not be placed on a base.
The hotplate surround should be level with, or above,
any adjacent work surface. A gap of 75mm should be left
between each side of the cooker ABOVE the hotplate level
and any adjacent vertical surface.
�����
���
�����
���
For non-combustible surfaces (such as unpainted metal or
ceramic tiles), this can be reduced to 25mm.
A minimum space of 650mm is required between the top of
the hob and a horizontal combustible surface.
Nn
Fig.7-2 shows the suggested clearances above the cooker.
*Any cooker hood should be installed in accordance with the
hood manufacturer’s instructions.
Fig.7-2
�����������
Surfaces of furniture and walls at the sides and rear of the
appliance should be heat, splash and steam resistant. Certain
types of vinyl or laminate kitchen furniture are particularly
prone to heat damage and discolouration. We cannot accept
responsibility for damage caused by normal use of the
cooker to any material that de-laminates or discolours at
temperatures less than 65°C above room temperature.
���������
����
����
ArtNo.11e cooker
We recommend a gap of 1120mm between units to allow
for moving the cooker. Do not box the cooker in – it must
be possible to move the cooker in and out for cleaning and
servicing.
Fig.7-3
A clearance of 130mm is required if the cooker is near a
corner of the kitchen, to allow the oven doors to open
(Fig.7-3). The actual opening of the doors is slightly less, but
this allows for some protection of your hand as you open the
door.
o.110-0009 - 110 induction door cleara
����������
Unpacking the Cooker
Do not take any packaging off the cooker until it is directly
in front of the place in which it is to be installed (unless it will
not fit through a door in its outer packaging).
Fig.7-4
Cut the banding straps and lift the cardboard box off the
cooker, leaving the cooker standing on the base packaging.
See the loose unpacking sheet.
Moving the Cooker
ArtNo.010-0001 Removing th
On no account try and move the cooker while it is
plugged into the electricity supply.
The cooker is very heavy, so take great care.
Fig.7-5
We recommend two people manoeuvre the cooker. Ensure
that the floor covering is firmly fixed, or removed to prevent it
being disturbed when moving the cooker around.
110-0006 Removing the
From the back tilt the cooker forward and remove the rear
half of the polystyrene base pack (Fig.7-4). Repeat from the
front and remove the front half of the poly base. Pull the
drawer out to its furthest point (Fig.7-5).
Fit the levelling tool on the rectangular adjuster (Fig.7-6).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
LOWER THE FRONT ROLLER by doing 14 complete (360°) turns
clockwise (Fig.7-6). (This means turning and removing the
levelling tool 56 times).
Fig.7-6
����
Now LOWER THE TWO REAR ROLLERS. First fit the levelling
tool on the hexagonal adjusting nut (Fig.7-7). Make 10
complete (360º) turns clockwise (Fig.7-8). (This means
turning and removing the levelling tool 20 times.)
ArtNo.010-0008 Lowering the front rollers
Make sure you lower BOTH REAR ROLLERS. There are two
adjusting nuts, one for each roller, at both the front bottom
corners of the cooker.
Unfold the rear edge of pack base tray. Carefully push the
cooker backwards out of the base pack (Fig.7-9). Push the
cooker close to its final position, leaving just enough space to
get behind it.
Fig.7-7
ArtNo.010-0002 Rear roller nut
Completing the Move
Unfold the rear edge of the pack base tray. Open the grill
door and right hand oven door so that you can get a good
grip on the bottom of the fascia panel as you move the
cooker.
Grip under the fascia panel and lift the front of the cooker
slightly (Fig.7-10). Carefully push the cooker backwards off
the pack base. Remove the pack base tray. Position the cooker
close to its final position, leaving just enough space to get
behind it.
Fig.7-8
DO NOT use the door handles or control knobs to
manoeuvre the cooker.
ArtNo.010-0003 Lowering the rear rollers
Repositioning the Cooker following
Connection
x10
If you need to move the cooker once it has been connected,
make sure it is switched off at the supply switch before
gripping under the fascia panel and lifting the front of the
cooker slightly (Fig.7-10). Check behind the cooker to ensure
that the electricity cable is not caught. As you progress,
always ensure that the cable has sufficient slack to allow the
cooker to move.
Fig.7-9
ArtNo.010-0009 Pushing the cooker
If a stability chain is fitted, release it as you ease the cooker out.
Do not forget to refit it when you replace the cooker.
When you replace the cooker, check behind it again once
more to ensure that the electricity cable is not caught or
trapped.
Fig.7-10
Levelling
It is recommended that you use a spirit level on a shelf in one
of the ovens to check for level.
Place the cooker in its intended position, taking care not to
twist it within the gap between the kitchen units as damage
may occur to the cooker or the units.
The rollers can be adjusted to level the cooker. To adjust
the height of the rear of the cooker, use the levelling tool
supplied to turn the adjusting nuts at the front bottom
corners of the cooker.
ArtNoving the coo
Adjust the height of the front roller to level the cooker. Turn
20
Download from Www.Somanuals.com. All Manuals Search And Download.
clockwise to raise the cooker and anticlockwise to lower.
Fig.7-11
When you are satisfied with the height and level, raise the
front of the cooker by one turn of the front roller adjuster.
Screw down the front feet to meet the floor. Screw the front
roller adjuster anticlockwise to raise the front roller so that
the front of the cooker is supported on the feet, not the front
roller, to prevent accidental movement of the cooker.
�
�
Leave the levelling tool on the adjuster with the handle of the
tool facing the rear of the cooker, so that the customer can
use it if they wish to move the cooker.
�����
���
Replace the drawer by locating it on the side runners and
pushing in.
ArtNo.130-0010 Electricl conections single-phase
������������
Electrical Connection
The cooker must be installed by a qualified electrician, in
accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
Fig.7-12
��
�
��
WARNING: THE APPLIANCE MUST BE EARTHED.
Note: The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double pole
switch, having a contact separation of at least 3mm in all
poles.
��
����
���
�����
���
The cooker must not be connected to an ordinary
domestic power point.
ArtNo.130-0010 Eectrical connections 3-phase
�����
�������������
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel. Connect
the mains cable to the correct terminals for your electrical
supply type (Fig.7-11 and Fig.7-12). Check that the links are
correctly fitted and that the terminal screws are tight. Secure
the mains cable using the cable clamp.
Fig.7-13
Hob Check
Check each cooking zone in turn. Be sure to use pans of the
correct size and material.
Secng the 110 plinth
Grill Check
Turn on the grill control and check that the grill heats up.
Oven Check
Set the clock as described earlier, and then turn on the ovens.
Check the oven fans start to turn and that the ovens heat up.
Fitting the Plinth
Loosen the three screws along the front bottom edge of the
cooker. Hook the central keyhole over the central screw. Twist
and fit each end keyhole over their respective screws. Tighten
the fixing screws (Fig.7-13).
Please complete your contact details in the front of this
section. Please inform the user how to operate the cooker
and hand over the instruction pack.
Thank you.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
8. Servicing
Disconnect the cooker from the electricity supply
before servicing, particularly before removing any
of the following: control panel, side panels, ceramic
hob, or any of the electrical components or cover
boxes.
Fig.8-1
008 - Classic
ing the end caps
Before reconnection, check that the appliance is
electrically safe.
1. To Remove a Side Panel
Disconnect from electricity supply.
Pull the cooker forward. Pull off the control panel end caps
at each end of the panel (Fig.8-1). Remove the fixing screws
under the end caps.
Remove the retaining screws for each panel (one at the front,
two at the rear, and one at each lower front corner of the side
panels).
Reassemble in reverse order.
2. To Lift up the Ceramic Hob
Disconnect from electricity supply.
Remove the side panels (see 1) to allow access to the hob
fixing screws (1 each side) at the top of the side uprights.
Remove these screws.
Lift up the ceramic hob at the front and prop in position with a
non-metallic prop.
CAUTION: The ceramic hob material is much more sensitive
to scratches on the underside than the top.
Take care not to touch or scratch the underside of the ceramic
as this will weaken the material and cause the top to shatter.
3. To Remove the Control Panel
Disconnect from electricity supply.
Pull off the control panel end caps at each end of the panel
(Fig.8-1). Remove the fixing screws under the end caps.
Pull off all the control knobs. Open the grill and right-hand
oven door and remove the control panel fixing screws
underneath the control panel. The screws directly below the
clock are for the clock fixing bracket, so do not remove them
at this stage.
Lift the control panel, pull forward and disconnect the wiring
from the rear.
Reassemble in reverse order. When replacing leads, refer to
the wiring diagram in this manual. Check the operation of the
timer.
4. To Replace a Hob Element
Disconnect from electricity supply.
Lift up the ceramic hob (see 2). The Induction Heating
Elements (IHE) are now accessible. Note the wire connection
positions and element orientation for re-assembly. Disconnect
the wires, and remove the element unit and springs. Re-
assemble in the reverse order.
Note: The IHE will require commissioning when the hob has
been refitted.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
5. To Replace a Light Switch
Fig.8-2
Fig.8-3
Disconnect from electricity supply.
Remove the control panel (see 3).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back its locking wings and pushing
forward. Fit the new bezel to the control panel by first lining
up the raised key on its body with the cut-out in the control
panel and pushing it in from the front.
�
�
ArtNo.320-0001 Door hinge
ArtNo.320-0001 Door hinges
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the Control Panel in reverse order and test for correct
operation.
6. To Remove the Electronic Timer
Disconnect from electricity supply.
Remove the control panel (see 3). Pull off the timer control
button(s).
Remove the timer/mounting bracket assembly from the
control panel by removing the fixing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling the
unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram in this manual. Check the operation of
the timer.
7. To Replace a Thermostat
Disconnect from the electricity supply.
Lift up the hob (see 2) and remove the control panel (see 3).
Open the oven door. Remove the oven furniture and slide out
the oven roof liner if fitted.
For the right-hand oven, remove the thermostat phial cover
(two screws). Unclip the thermostat phial from the clips in the
oven back.
For the left-hand oven, pull cooker forward to gain access
to the cover box at the rear of the cooker. Remove the four
screws securing the cover and lift clear.
Feed the thermostat capillary out of the oven. Disconnect
the wiring from the thermostat. Remove two screws holding
thermostat to mounting panel. Fit new thermostat and
reassemble in reverse order. Ensure that the phial is clipped to
the oven back with the phial centrally positioned between the
clips.
Check the operation of the thermostat.
8. To Remove the Grill Door
Remove the left-hand side panel (see 1). Remove the ceramic
hob (see 1). Remove the centre cover strip (5 screws, 2 top, 2
bottom, 1 in middle). Remove the two countersunk screws (1
each side) securing the grill hinge arms to the front of the grill
chamber.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
Note: The arms are spring tensioned. Carefully remove the grill
Fig.8-4
door. Retain the gaskets.
Reassemble in reverse order ensuring that the gasket is fitted
between the hinge arm and the front of the grill chamber.
9. To Replace the Grill Controller
Disconnect from electricity supply.
06 Oven door hinge
Lift up the hob (see 2) and remove the control panel (see 3).
Disconnect the wiring from the controller. Remove the two
screws holding the controller to the mounting panel. Fit the
new controller and reassemble in reverse order. Check for
correct operation.
Effect of hinge adjustment - exagerrated for clarity
Centreline of hinge pin
Fig.8-5
10. To Remove the Grill Element
Disconnect from electricity supply.
Remove grill pan from inside the grill compartment; remove
the enamelled front shield from the grill roof, by undoing the
two screws and washers.
Remove the two screws and washers securing the grill
element front support. Remove the screws from the grill
element.
ArtNo.320-0007 Oven door hinge adjustment 2
Lift the element out carefully, disconnecting the leads from
the element terminals (noting their position). If it is not
possible to disconnect the leads in this way, pull the cooker
forward to gain access to the rear, remove the screws securing
the electric cover to the back sheet, remove the cover and
disconnect the terminals from the rear.
Oven door omitted for clarity
Fig.8-6
Fit the new element and reassemble in reverse order. Check
the operation of the grill.
11. To Replace an Oven Door
Open the oven door. Support the door and remove the two
screws securing the upper hinge and gasket to the cooker
front (Fig.8-2). Remove the door from the lower hinge by
lifting slightly and moving outwards (Fig.8-3).
ArtNo.320-0002a Proplus oven door side screws
The door is heavy, so take care.
Reassemble in reverse order.
12. To Adjust an Oven Door Angle
The bottom hinge of either oven door can be adjusted to alter
the angle of the door (Fig.8-4). Loosen the bottom hinge
fixing screws and use the notch and a flat bladed screwdriver
to move the position of the hinge to set the hinge position
(Fig.8-5).
Retighten the hinge screws.
13. To Replace an Oven Door Outer Panel
Move the cooker forward to gain access to the sides.
Open the oven door slightly and remove the front panel fixing
screws from the door sides – two each side (Fig.8-6).
Carefully lift off the outer door panel.
Remove the door handle from the panel by unscrewing the
two retaining nuts. Fit the door handle to the new panel.
Fit the panel to the door. Reassemble in reverse order.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
14. To Change the Oven Door Latch
Fig.8-7
ArtNo.320-0004 Oven doFig.8-8
Remove the outer door panel (see 13). Remove screws ‘B’that
hold the latch assembly to the inner door panel (Fig.8-7). Fit
the new catch and reassemble in reverse order.
Verify the door operation.
15. To Adjust an Oven Door Catch Keep
�
Open the oven door, and slacken off the locknut at the base of
ArtNo.320-0003 Oven doolatch
the keep (Fig.8-8).
Screw in or out as required until the required fit is obtained.
Retighten the locking nut.
Fig.8-9
16. To Replace an Oven Door Seal
Open the oven door. The seal has small hooks that hold it in
place by locating into holes in the rear door face on the main
oven and oven front face on tall oven. At the corner, pull the
seal diagonally away from the door centre until the hook is
released (Fig.8-9). Proceed to the next hook and release it in a
similar way, and so on.
You can use force if the hooks are stiff, as the old seal will be
discarded.
Carefully lift away the inner back. Reassemble in reverse
order making sure that the four screws and washers are fully
tightened.
ArtNo.320-0005 Oven door rubber seal
Fig.8-10
17. To Remove an Oven Element Thermal Cut-out
Disconnect from electricity supply.
Pull the cooker forward to gain access to the cover box. Undo
the cover screws and lift clear. The cut-out is located on the
earth plate beside the oven element connections. Disconnect
the cut-out wiring. Undo the fixings that secure the cut-out to
the earth plate and remove. Fit the replacement control and
re-assemble in reverse order.
18. To Remove an Oven Inner Back
Disconnect from electricity supply.
Open the door and remove the shelves. Remove the screws
and washers securing the inner back to the back of the oven
(Fig.8-10). Carefully lift away the inner back. Reassemble in
reverse order making sure that the screws and washers are
fully tightened.
Fig.8-11
19. To Remove the Fan Oven Element
��������������������
Disconnect from electricity supply.
Remove the oven inner back (see 18). Remove the two screws
from the top of the element and the one from the bottom of
the element inside the oven (Fig.8-11).
ArtNo.321-0005 Fan oven element
Lift the element out carefully, disconnecting the terminals
connected to the element (noting their positions).
If it is not possible to disconnect the leads in this way, pull the
cooker forward to gain access to the rear.
Remove the screws securing the electric cover to the back
sheet, remove the cover and disconnect the terminals from
the rear.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have finished.
20. To Replace an Oven Fan
Fig.8-12
Disconnect from electricity supply.
Pull the cooker forward to gain access to the rear. Remove
the screws securing the electric cover to the back sheet and
remove the cover.
ArtNo.322-0002 Oven bottom element access
�
�
Disconnect the three terminals connected to the fan noting
their position. Remove the oven inner back (see 18). Hold the
fan blade and remove the centre nut (left-hand thread) two
brass washers, fan blade and circlip. Unscrew the fan retaining
nuts and washers (three off each) and lift the fan away from
the rear of the cooker. Fit the new fan and reassemble in
reverse order. Check the operation of the oven.
�
Fig.8-13
Fig.8-14
21. To Remove the Left-hand Oven Bottom and Top
Elements
Disconnect from the electricity supply.
ArtNo.324-0005 Oven light bulb
Bottom Element
Art-0007 Unscrewing the bulb cover
Pull the cooker forward to access the cover boxes at the rear
of the unit. Remove the fixings that secure the cover and lift it
clear.
Remove the two screws ‘A’and allow the plate to drop down
(Fig.8-12). Remove the two screws B, lower the upper plate
and remove through the slot in the cooker back.
Undo the terminal connections, noting their positions.
Remove the element fixings and withdraw element. Replace
the element and re-assemble parts in reverse order.
Top Element
Open the left-hand oven door and undo the fixings that
secure the heat shield. Remove the top element bracket
fixings and withdraw element. Replace the element and re-
assemble parts in reverse order. Check that the oven operates
satisfactorily.
22. To Change Oven Light Bulb
Disconnect from electricity supply.
Make sure the oven is cool. Open the oven door and remove
the oven shelves. Remove the grill pan and support from the
grill chamber.
Unscrew the bulb cover by turning anticlockwise. It may be
very stiff (Fig.8-13).
Taking care to protect your fingers in case the bulb should
shatter, unscrew the old bulb.
Fit an Edison screw fitting 15W 240V lamp, FOR OVENS. It must
be a special bulb, heat resistant to 300°C (Fig.8-14).
Screw in the new bulb, and then screw back the bulb cover.
Turn on the electricity supply and check that the bulb now
lights.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.095-0002 - Circuit diagram - 110 Induction
9. Circuit Diagram: Oven
�
�
�
ArtNo.080-0029 110 induction (oven) circuit diagram
�
��
�
�
�
�
��
��
�
�
�
��
��
��
�
��
�
��
�
�
�
�
��
��
��
�
�
�
��
��
��
�
�
�
�
�
��
�
��
�
�
��
�
�
�
�
��
��
�
�
��
��
�
�
�
��
��
��
��
�
�
�
�
�������
��
�
��
�
�
�
��
��
�
�
�
�������
���
��
���
��
�
�
�
��
�
��
�
��
��
��
�
�
�
��
��
�
��
��
�
�
�
�
���
�
�
�
� ��
�
��
�
�
�
�
��
��
���
��
���
�
�
�
��
��
�
��
���
���
�
��
�
��
��
�
��
��
��
��
�� ��
� � � � � � � � �
���
�
�
�
�
�
Key
The connections shown in the circuit diagram are for single-phase. The ratings are for 230V 50Hz.
Code Description
Code Description
Colour Code
A1 Right-hand oven thermostat
A2 Right-hand oven thermostat front switch
A3 Right-hand oven fan element
A4 Right-hand oven fan
C
D1
D2
D3
F
Clock
b
Blue
Grill energy regulator
Grill elements
Grill front switch
Cooling fan
br Brown
bk Black
or Orange
B1 Left-hand zoned oven thermostat
r
v
Red
Left-hand zoned oven thermostat front
switch
G1
G2
H
Oven light switch
Oven light
Violet
White
Yellow
B2
w
y
B3 Zoned oven browning element (inner pair)
B4 Zoned oven top element (outer pair)
B5 Zoned oven base element
Thermal cut-out
Neon
J
g/y Green/yellow
gr Grey
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Circuit Diagram: Hob
To Earth
MCB
To T1 To T2 To T4 To T5
MCB MCB MCB MCB
br br
br
b
b
b
g/y
b
b
b
r
b
b
b
br
br
br
CU1
CU2
CU3
br
g/y
g/y
g/y
br
br
b
br
b
b
2.3kW
2.3kW
2.3kW
r
b
r
b
1.4kW
1.4kW
A
B
����������������������������������������������������
C
D
E
F
G
Code Description
Colour Code
A
B
C
D
E
Touchlite panel
b
Blue
Distribution board
br Brown
bk Black
or Orange
Left-hand front control
Left-hand rear control
Central control
r
v
Red
F
Right-hand front control
Right-hand rear control
Violet
White
Yellow
G
w
y
g/y Green/yellow
gr Grey
28
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.105-0002 - Technical data - 110 Induction
10. Technical Data
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION : Cooker back, serial number repeater badge below oven door opening.
Connections
220 - 240V 50Hz
Electric
Dimensions
Overall height
minimum 902mm
maximum 927mm
Overall width
1100mm
650mm
Overall depth
Refer to 'Positioning the Cooker'.
Ratings
�����
�����
�����
�����
�����
Conventional
Forced air convection
Oven
Browning element
Ovens
2.5kW
1.15kW
2.5kW
A
Energy efficiency class on a scale
of A (more efficient) to G (less efficient)
A
Energy consumption based on standard load
0.99kWh
67
0.85kWh
67
Usable volume (litres)
Size
Large
Large
Time to cook standard load
Surface area of the grid
40 minutes
1400cm2
38 minutes
1400cm2
Grill
2.3kW
Maximum total electrical load at 230V 17.4kW (approximate total including oven lights, oven fan, etc.)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.000-0001 - Back cover Rangemaster
����������������������������������������
ANo.000-0003 E logo
Download from Www.Somanuals.com. All Manuals Search And Download.
|