43-1097a.fm Page 1 Tuesday, August 31, 1999 10:01 PM
Cat. No. 43-1097 A
OWNER’S MANUAL
Please read before using this equipment.
ET-927
Digital Spread Spectrum
900 MHz Cordless Telephone
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 3 Tuesday, August 31, 1999 10:01 PM
Mute — prevents the person on the oth-
er end of the phone line from hearing
your conversation with someone in the
room.
This symbol is intended to alert
you to the presence of uninsu-
lated dangerous voltage within
the product’s enclosure that might
be of sufficient magnitude to con-
stitute a risk of electric shock. Do
not open the product’s case.
Flash — sends an electronic switch-
hook signal for use with special phone
services such as Call Waiting.
This symbol is intended to inform
you that important operating and
maintenance instructions are
included in the literature accom-
panying this product.
Redial — lets you quickly dial the last
number dialed.
!
Hearing Aid Compatible — lets you
use this telephone with hearing aids that
have a T (telephone) switch.
Important:
• Cordless phones such as this one
require AC power to operate. When
AC power is off, you cannot dial out
or receive incoming calls using your
ET-927. For this reason, the ET-927
should not be your only telephone.
To be safe, you should also have a
phone that does not require AC
power to operate (not a cordless
phone), so you can still make and
receive calls if there is an AC power
failure.
Three Mounting Options — let you
place the phone on a desk top, or mount
it on a wall plate or directly on a wall.
This phone has been tested and found
to comply with all applicable UL and
FCC standards.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain
or moisture.
• Some cordless phones operate at
frequencies that might cause inter-
ference to nearby TVs and VCRs.
To minimize or prevent such interfer-
ence, the base of the cordless
phone should not be placed near or
on top of a TV or VCR.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 4 Tuesday, August 31, 1999 10:01 PM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
This telephone complies with Part 68 of
FCC Rules. You must, upon request,
provide the FCC Registration Number
and the REN to your phone company.
These numbers are on the label on the
bottom of the base.
Your telephone conforms to federal reg-
ulations, and you can connect it to most
telephone lines. However, each device
you connect to the phone line draws
power from the phone line. We refer to
this power draw as the device’s ringer
equivalence number, or REN. The REN
is on the bottom of the base.
You must not connect your phone to any
of the following:
• coin-operated systems
If you are using more than one phone or
other device on the line, add up all the
RENs. If the total is more than five (three
in rural areas), your phone might not
ring. If ringer operation is impaired, re-
move a device from the line.
• party-line systems
• most electronic key phone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 5 Tuesday, August 31, 1999 10:01 PM
CONTENTS
Installation ............................................................................................................... 6
Installing the Handset’s Antenna ........................................................................ 6
Selecting a Location ........................................................................................... 6
Preparation ............................................................................................................ 11
Connecting and Charging the Battery Pack ..................................................... 11
Setting the Dialing Mode .................................................................................. 12
Adjusting the Ringers ....................................................................................... 13
Operation ............................................................................................................... 14
Making/Answering Calls ................................................................................... 14
Adjusting the Volume ........................................................................................ 14
Using REDIAL ................................................................................................... 14
Using MUTE ...................................................................................................... 15
Using FLASH .................................................................................................... 15
Using Tone Services on a Pulse Line ............................................................... 15
Special Features ................................................................................................... 16
Memory Dialing ................................................................................................ 16
Using the Intercom ........................................................................................... 17
Using an Optional Headset .............................................................................. 18
Troubleshooting .................................................................................................... 20
Out-of-Range Indications ................................................................................. 22
Care and Maintenance .......................................................................................... 23
Replacing the Battery Pack .............................................................................. 24
The FCC Wants You to Know ........................................................................... 25
Lightning ........................................................................................................... 25
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 6 Tuesday, August 31, 1999 10:01 PM
INSTALLATION
• The USOC number of the jack to be
installed is RJ11C (RJ11W if you
want to mount it on a wall plate).
INSTALLING THE
HANDSET’S
ANTENNA
Power the ET-927 using the supplied
9V, 500-mA AC adapter.
illus
Insert the antenna into the
hole on the top of the hand-
set, then twist the antenna
clockwise until it is secure.
Cautions:
You must use a Class 2
power source that supplies
!
9V DC and delivers at least
500 mA. Its center tip must be set to
positive and its plug must fit the ET-
927's DC 9V jack. The supplied
adapter meets these specifications.
Using an adapter that does not meet
these specifications could damage
the phone or the adapter.
SELECTING A LOCATION
You can place the phone on a desk top,
or mount it on a wall plate or directly on
a wall. Select a location that is:
• near an AC outlet
• near a telephone line jack
• Always connect the AC adapter to
the ET-927 before you connect it to
AC power. When you finish, discon-
nect the adapter from AC power be-
fore you disconnect it from the
phone.
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
The base’s location affects the phone’s
range. If you have a choice of several lo-
cations, try each to see which provides
the best performance.
Placing on a Desk Top
1. Push in the two tabs on the top of
the mounting bracket, then lift off
just the upper part of the bracket.
Notes:
illus -- enlarge to fill space
• Your telephone connects directly to
a modular telephone line jack. If
your phone line jack is not a modu-
lar jack, you can update the wiring
yourself, using jacks and adapters
available at your local RadioShack
store. Or, you can let the phone
company update the wiring for you.
2. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 7 Tuesday, August 31, 1999 10:01 PM
the back of the base, route the
adapter cord through the strain relief
slot and the hole on the bracket,
then push in the mounting bracket’s
upper end to click the bracket into
place.
6. For the best reception, raise the
base’s antenna to a vertical position.
Illus
illus -- label strain relief
Mounting on a Wall Plate
3. Plug one end of the supplied long
modular cord into the phone line
jack on the back of the base.
1. Push in the two tabs on the top of
the mounting bracket, then lift off the
entire bracket.
illus -- enlarge to fill space
Illus
2. Plug one end of the supplied short
modular cord into the phone line
jack on the back of the base, then
press the cord into the center
groove on the bottom of the base.
4. Plug the AC adapter into a standard
AC outlet.
Illus
Illus
5. Plug the modular cord’s other end
into a modular phone line jack.
Illus
3. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the base. Then route the
cord through the strain relief slot
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 8 Tuesday, August 31, 1999 10:01 PM
and press the cord all the way down
into the cord groove on the bottom
of the base.
6. Plug the modular cord’s other end
into the wall plate’s modular phone
line jack.
illus -- label strain relief
Illus
7. Align the keyhole slots on the
bracket with the studs on the wall
plate, then slide the base downward
to secure it.
4. Position the mounting bracket with
the narrow end on top. Route the
short modular cord through the cen-
ter hole of the bracket, and insert
the two tabs at the top of the bracket
into the matching slots on the base’s
back, near the jacks.
illus -- show modular
cord already connected
Illus
8. Plug the AC adapter into a standard
AC outlet.
Illus
5. Press the two tabs at the bottom of
the bracket into the matching slots
on the back of the base to lock the
bracket into place.
9. For the best re-
ception, raise the
Illus
base’s antenna to
a vertical position.
Illus
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 9 Tuesday, August 31, 1999 10:01 PM
4. Insert the supplied AC adapter’s
barrel plug into the DC 9V jack on
the back of the base, route the cord
through the strain relief slot, then
press the cord into the groove on
the bottom of the base.
Mounting Directly on the Wall
For this mounting method, you need two
wood screws (not supplied) with heads
that fit into the keyhole slots on the
mounting bracket.
3/16
1. At the desired mounting
illus -- label strain relief
location, drill two holes
15
16
3 / inches (100 mm)
apart. Then thread a
screw into each hole,
315/16
letting the heads extend
3
16
about / inch (5 mm)
from the wall.
5. Position the mounting bracket with
the narrow end on top. Insert the
two tabs at the top of bracket into
the matching slots on the base’s
back, near the jacks.
2. Push in the two tabs on the top of
the mounting bracket, then lift off the
entire bracket.
add illus like that below
Step 1 of previous section
Illus
3. Plug one end of the supplied long
modular cord into the phone line
jack on the back of the base. Then
press the cord into the center
groove on the bottom of the base.
Press the two tabs at the bottom of
the bracket into the matching slots
on the back of the base to lock the
bracket into place.
Illus
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 10 Tuesday, August 31, 1999 10:01 PM
6. Align the keyhole slots on the
mounting bracket with the screws on
the wall, then slide the base down-
ward to secure it.
Illus
7. Plug the ET-927’s AC cord into a
standard AC outlet.
Illus
8. Plug the long modular cord into a
modular phone line jack.
illus -- like that below Step
5 of previous section
9. For the best reception, raise the
base’s antenna to a vertical position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 11 Tuesday, August 31, 1999 10:01 PM
PREPARATION
Notes:
• You can hang the handset face up
CONNECTING AND
CHARGING THE BATTERY
PACK
on the base if it is wall-mounted
(using the slot on the back of the
handset); however, the battery pack
will not fully charge in this position.
The ET-927 comes with a rechargeable
nickel-cadmium battery pack in the
handset, but not connected. Before us-
ing your phone, you must connect the
battery pack, then charge it for about 24
hours.
• When you first use your phone after
charging or recharging the battery
pack, the handset might not work or
it might sound an error tone when
you press TALK. If this happens,
place the handset on the base for
about 5 seconds, then try again.
1. Slide off the handset’s battery com-
partment cover.
• If the CHARGE indicator does not
light when you place the handset on
the cradle, be sure the battery pack
and AC adapter are correctly and
securely connected.
Illus
2. Insert the battery pack’s
connector with its flat
side up into the phone’s
illus of indicator
location
Illus
socket. The connector
fits only one way.
3. Replace the cover.
Also, check the charging contacts
on both the handset and base. If the
contacts are dirty or tarnished, clean
them with a pencil eraser.
To charge the battery pack, place the
handset on the base.
Recharge the battery pack when the
BATT LOW indicator on the handset
lights.
illus of contacts’
location
add illus of indicator
location
If the battery and AC connections
are correct and secure and the
charging contacts are clean, the bat-
tery might be fully charged. This is
not a malfunction.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 12 Tuesday, August 31, 1999 10:01 PM
• If the phone stops operating prop-
erly, check the base’s phone line
cord and AC adapter connections. If
the connections are secure but the
phone still does not work, unplug
the base’s AC adapter from the AC
outlet and disconnect the handset’s
battery pack. Wait 3 minutes, then
reconnect the battery pack and plug
the AC adapter back into the AC
outlet. The phone should operate
properly.
SETTING THE DIALING
MODE
Set T/P (Tone/Pulse) for the type of ser-
vice you have. If you are not sure which
type you have, do this test after the bat-
tery pack is fully charged.
1. Set T/P on the back of base to T.
Illus
• If the battery pack becomes weak,
the handset sounds a short beep
every 16 seconds during a call and
the BATT LOW indicator flashes.
Within about 10 minutes, the phone
will automatically disconnect. Re-
charge the battery pack.
2. Press TALK and listen for a dial
tone.
Illus
• If the battery pack loses its charge
completely or the base loses power
while the handset is away from it,
the security access-protection code
needs to be reset. To reset the secu-
rity code, place the handset on the
base. If it was the handset that lost
power, leave the handset on the
base to charge the battery pack.
3. Press any number other than 0.
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until the BATT
LOW indicator turns on. Otherwise,
it loses its ability to fully recharge,
and you might have to recharge and
replace it more often.
If the dial tone stops, you have
touch-tone service. Leave T/P set to
T.
If the tone continues, you have
pulse (rotary) service. Set T/P to P.
4. To hang up, either place the handset
on the base or press TALK so the
TALK indicator on the handset and
the IN USE indicator on the base
turn off.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 13 Tuesday, August 31, 1999 10:01 PM
Note: Even if you turn off the ringer on
the handset or base, you can still make
calls using that keypad, and you can still
answer calls if you hear another phone
on that same line ring (see “Operation”
on Page 14).
ADJUSTING THE
RINGERS
The ET-927’s handset and base each
have four different ringer tones. You can
set the base’s and handset’s ringer tone,
or turn off the ringer on either or both.
Setting the Ringer’s Volume
Turning On/Off the Ringers
To adjust the ringer’s volume when the
phone is not in use, repeatedly press
VOLUME ▲ or ▼ on the handset.
To have the base ring when a call
comes in, set RINGER ON/OFF on the
back of the base to ON.
Checking/Setting the Ringer
Tone
Illus
The base and handset are both preset
to use the same ringer tone (1). To
change or hear the different tones, press
FLASH then 1, 2, 3, or 4 when the phone
is not in use. (The last number button
you pressed is the tone you will hear.)
To have it not sound, set RINGER ON/
OFF to OFF.
To have the handset ring when a call
comes in, set RINGER ON/OFF on the
handset’s left side to ON.
add illus of FLASH
location of handset’s
RINGER ON/OFF
set to ON
To have it not sound, set RINGER ON/
OFF to OFF.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 14 Tuesday, August 31, 1999 10:01 PM
OPERATION
MAKING/ANSWERING
CALLS
ADJUSTING THE VOLUME
The handset’s VOLUME control lets you
set the volume you hear through the
handset to one of four levels.
To make a call, lift the handset and
press TALK. When you hear the dial
tone, dial the number.
illus -- add callout to
TALK indicator
Illus
To turn the volume up or down during a
call, repeatedly press VOLUME ▲ or ▼
on the handset. The ET-927 beeps once
each time you press VOLUME ▲ or ▼.
When you reach the highest or lowest
volume level, the ET-927 beeps three
times.
To answer a call when the handset is on
the base, just lift the handset and begin
your conversation.
To answer a call when the handset is
not on the base, press any key on the
handset before speaking.
Both the IN USE indicator on the base
and the TALK indicator on the handset
flash when you receive a call, and the
TALK indicator lights steadily while the
handset is in use.
USING REDIAL
To redial the last number dialed, press
REDIAL when you hear the dial tone.
To end a call, place the handset on the
base or press TALK so the TALK indica-
tor on the handset turns off.
Illus
Important: If you move the handset out-
side the base’s range (about 550 feet),
the handset will not operate properly
and a call in progress might be discon-
nected (see “Troubleshooting” on
Page 20).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 15 Tuesday, August 31, 1999 10:01 PM
USING MUTE
USING TONE SERVICES
ON A PULSE LINE
The MUTE button on the handset lets
you talk to someone else in the room
without the person on the other end of
the phone line hearing your conversa-
tion. Press MUTE during the call. The
BATT LOW indicator on the handset
lights steadily.
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these services.
With T/P set to P, just press
when
you want to begin sending tones. Any
additional numbers you dial are sent as
tone signals. When you hang up, the
phone automatically resets to the pulse
mode.
Illus
illus
Press MUTE again to resume your
phone conversation. The BATT LOW in-
dicator turns off.
USING FLASH
You can use FLASH on the handset to
produce a switchhook signal for special
phone services, such as Call Waiting. If
you have Call Waiting, press FLASH to
take an incoming call without discon-
necting the current call. Press FLASH
again to return to the first call.
illus -- make sure all
button labels are visible
Note: If you do not have any special
phone services, pressing FLASH might
disconnect the current call.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 16 Tuesday, August 31, 1999 10:01 PM
SPECIAL FEATURES
at the appropriate place in the
sequence of numbers.
MEMORY DIALING
You can store up to 20 numbers of up to
16 digits each in the ET-927’s memory,
then dial them with the press of a few
buttons.
• Each
or pause entry (see
“Storing a Pause”) counts as one
digit in memory.
3. Press MEM then press the number
key (01–20) of the memory location
where you want to store the number.
The ET-927 beeps twice and stores
the number.
Storing a Number
Notes:
• You must complete these steps
within 30 seconds of each other. If
you do not, the ET-927 sounds a
long beep, all indicators stop flash-
ing, and you must start over again at
Step 1.
Notes:
• To change a number in memory,
store a new one in its place.
• To erase a number from memory,
repeat Steps 1 and 3, skipping Step
2.
• You can store special banking or
telephone service numbers (such as
access codes or account numbers)
in memory, but for security pur-
poses, we recommend that you do
not store private numbers (such as
personal identification numbers or
passwords) in memory.
Storing a Pause
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect.
1. Press MEM (memory) on the hand-
set. The TALK indicator on the
handset and IN USE indicator on
the base flash.
To add one or more 2-second pauses to
a phone number you are storing in
memory, press REDIAL at each point
where a pause is needed.
Illus
Note: Each pause entry counts as one
digit in memory.
2. Enter the number you want to store.
Notes:
• If you have pulse service and
want to send tone signals, press
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 17 Tuesday, August 31, 1999 10:01 PM
Dialing a Stored Number
USING THE INTERCOM
To dial a stored number, when you hear
the dial tone, press MEM then the de-
sired memory location number (01–20).
You can use the ET-927 as a two-way
pager and intercom between the base
and the handset. This is useful if the
handset is away from the base and you
want to locate it, or if you want to have a
conversation between someone with the
handset and someone at the base.
Chain Dialing Service Numbers
You can make a call using more than
one of the ET-927’s memory locations.
This is called chain dialing. Chain dialing
is useful for dialing special services such
as alternate long distance or bank-by-
phone.
Notes:
• If a call comes in during an intercom
conversation, the person using the
handset can answer the call, but the
intercom call is disconnected.
When calling special services, dial the
service’s main number first. Then, at the
appropriate place in the call, press MEM
and the number for the memory location
where the additional information is
stored.
• If the handset is in use when it
receives a page, the person using
the handset hears one quiet ring
over the phone.
Paging from the Base to the
Handset
Testing Stored Emergency
Numbers
To send a page from the base to the
handset, press PAGE on the base. The
handset beeps twice per second for 15
seconds. The base’s PAGE indicator
flashes while the handset beeps.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you want to test
the stored number, make the test call
during the late evening or early morning
hours to avoid peak demand periods. Al-
so, remain on the line to explain the rea-
son for your call.
illus -- add callout to
PAGE indicator
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 18 Tuesday, August 31, 1999 10:01 PM
To answer a page at the handset, press
INTCM. Begin your conversation after
the INTCM indicator on the handset
lights steadily.
USING AN OPTIONAL
HEADSET
Your ET-927’s handset is equipped with
a headset jack on top. This jack allows
you to connect a headset for hands-free
conversation — perfect for when you are
working in the yard or garage. A handset
holder carries the handset for you while
you use the headset. (Headsets and
handset holders are available at your lo-
cal RadioShack store.)
Illus
To end an intercom call, press PAGE on
the base or INTCM on the handset. All
indicators turn off.
Follow these steps to use a headset.
1. Place the ET-927’s handset in the
handset holder.
Paging from the Handset to the
Base
To send a page from the handset to the
base, press INTCM on the handset. The
base sounds two short beeps, and auto-
matically answers the handset’s page
(whether or not anyone is there). Begin
your conversation after the INTCM indi-
cator lights steadily on the handset.
illus of handset in holder
3
32
2. Insert the headset’s / -inch (2.5
mm) plug into the
of the handset.
jack on the top
To end an intercom call, press PAGE on
the base or INTCM on the handset. All
indicators turn off.
Illus
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 19 Tuesday, August 31, 1999 10:01 PM
3. Place the headset on your head with
the earpiece over either ear and
adjust the microphone boom until it
is about even with your chin.
illus -- enlarge to fill
space
4. Clip the handset on your belt.
illus -- don’t show back
of clip; it would not be
visible if it was attached
to a person’s belt
5. Make or receive calls as you would
normally.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 20 Tuesday, August 31, 1999 10:01 PM
TROUBLESHOOTING
We do not expect you to have any problems with your phone, but if you do, the follow-
ing suggestions might help.
Problem
Solution
Low volume or unusual sounds.
Someone has picked up another phone
on the same line. Hang up the other
phone.
Press VOLUME ▲ on the handset to turn
up the handset’s volume.
Noise interference.
Return the handset to the cradle for a few
seconds to reset the security access pro-
tection code, then try again.
You might be moving out of range (see
“Out-of-Range Indications” on Page 22).
Move the handset closer to the base or
relocate the base.
Keep the handset away from computers,
remote controlled toys, wireless micro-
phones, alarm systems, intercoms, room
monitors, fluorescent lights, and electrical
appliances.
Move to another location or turn off the
source of interference.
The phone cannot be operated at a
useful distance from the base
because the signal becomes weak or
noisy (the handset’s range has
decreased).
Adjust the base’s antenna so it stands
straight up.
Be sure neither antenna is touching a
metal surface.
Return the handset to the cradle, and re-
charge the battery pack.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 21 Tuesday, August 31, 1999 10:01 PM
Problem
Solution
The phone does not work or works
poorly.
Be sure the base’s phone line cord and
AC adapter are correctly and securely
connected. If that does not help, unplug
the base’s AC adapter from the AC outlet
and disconnect the handset’s battery
pack. Wait 3 minutes, then reconnect the
battery pack and plug the AC adapter
back into the AC outlet.
The handset battery pack does not
charge.
Check the charging contacts on the
handset and base. If they are dirty, clean
them with a pencil eraser.
The handset does not ring or receive
a page.
Be sure the handset’s ringer is turned on.
Adjust the base’s antenna so it stands
straight up.
Move closer to the base.
Move the base away from noise sources.
The battery pack might be weak. Charge
the battery pack by placing the handset
on the base for 15–24 hours.
Return the handset to the base to reset
the security code.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Adjust the base’s antenna so it stands
straight up.
Be sure the handset’s battery pack is
charged. (If the battery power is too low,
it does not have enough power to light
the BATT LOW indicator.)
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your phone to your local RadioShack store for assistance.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 22 Tuesday, August 31, 1999 10:01 PM
OUT-OF-RANGE
INDICATIONS
If you move the ET-927’s handset out of
the base’s range, the handset will not
operate properly.
If you move the handset out of the
base’s range when the handset is not in
use, the handset’s BATT LOW indicator
flashes and the handset beeps twice at
16-second intervals. When you move
the handset back within range of the
base again, the out-of-range indications
stop.
If you move the handset out of the
base’s range while a call is in progress,
two beeps sound through the earpiece
every 3–4 seconds and the BATT LOW
indicator flashes, and you and the other
party cannot hear each other.
If you move the handset back within the
base’s range within 30 seconds, the out-
of-range indications stop, and you can
resume your phone conversation.
If you keep the handset out of the base’s
range for 30 seconds or more, two
beeps sound through the earpiece every
3–4 seconds and the BATT LOW indica-
tor flashes. After 30 seconds, the call is
disconnected, the handset beeps twice
every 16 seconds and the BATT LOW
indicator keeps flashing. When you
move the handset back within range of
the base again, the out-of-range indica-
tions stop.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 23 Tuesday, August 31, 1999 10:01 PM
CARE AND MAINTENANCE
Your RadioShack ET-927 Digital Spread Spectrum 900 MHz Cordless Telephone is
an example of superior design and craftsmanship. The following suggestions will help
you care for your phone so you can enjoy it for years.
Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids might
contain minerals that can corrode the electronic circuits.
Use and store the phone only in normal temperature environments. Tem-
perature extremes can shorten the life of electronic devices, damage bat-
teries, and distort or melt plastic parts.
Keep the phone away from dust and dirt, which can cause premature wear
of parts.
Handle the phone gently and carefully. Dropping it can damage circuit
boards and cases and can cause the phone to work improperly.
Use only fresh batteries of the required size and recommended type. Bat-
teries can leak chemicals that damage your phone’s electronic parts.
Wipe the phone with a damp cloth occasionally to keep it looking new. Do
not use harsh chemicals, cleaning solvents, or strong detergents to clean
the phone.
Modifying or tampering with the phone’s internal components can cause a malfunc-
tion and might invalidate its warranty and void your FCC authorization to operate it. If
your phone is not performing as it should, take it to your local RadioShack store for
assistance. If the trouble is affecting the telephone lines, the phone company can ask
you to disconnect your phone until you have resolved the problem.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 24 Tuesday, August 31, 1999 10:01 PM
Cautions:
REPLACING THE
BATTERY PACK
• Use only a replacement battery
pack of the required type (3.6V, 600
mAh rechargeable battery pack).
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 11, the battery pack should last
about one year. If the battery pack will
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6V, 600 mAh battery pack that
has a connector which fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
• Be careful not to short the battery
pack with conducting materials,
such as rings, bracelets, and keys.
The battery pack or conductor might
overheat and burn.
Important: This phone’s
battery pack uses nickel-
cadmium rechargeable
batteries. At the end of a
nickel-cadmium battery's
useful life, it must be re-
cycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for infor-
mation on recycling or disposal pro-
grams in your area or call 1-800-843-
7422. Some options that might be avail-
able are: municipal curbside collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collec-
tion centers, and mail-back programs.
0
0
8
3
4
Install the new battery pack as de-
scribed here, then charge the battery
pack for 24 hours.
Note: To avoid losing phone numbers
stored in memory, try to install and begin
charging the new battery pack within
about 2 minutes.
1. Press down and slide off the hand-
set’s battery compartment cover.
Warnings:
Illus
• Dispose of the old battery pack
promptly and properly. Do not burn
or bury it.
2. Gently pull out the battery connector
to disconnect it, then remove the
battery pack.
• Do not open or mutilate the battery
pack. Swallowing battery parts can
be fatal.
3. Insert a fresh battery pack and plug
its connector with the flat side up
into the socket inside the battery
compartment. The connector fits
only one way.
4. Replace the cover.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 25 Tuesday, August 31, 1999 10:01 PM
To eliminate interference, you can try
one or more of the following corrective
measures:
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. The phone company
normally attempts to notify you in ad-
vance. If advance notice is not practical,
the phone company notifies you as soon
as possible and advises you of your
right to file a complaint with the FCC.
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
equipment and the radio or TV.
• Use outlets on different electrical cir-
cuits for the equipment and the
radio or TV.
Consult your local RadioShack store if
the problem still exists.
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The phone
company normally notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your phone service.
LIGHTNING
Your phone has built-in protection cir-
cuits to reduce the risk of damage from
surges in phone line current. These pro-
tection circuits meet or exceed FCC re-
quirements. However, lightning striking
the phone lines can damage your
phone.
This equipment complies with the limits
for a Class B digital device as specified
in Part 15 of FCC Rules. These limits
provide reasonable protection against
radio and TV interference in a residential
area. However, your equipment might
cause TV or radio interference even
when it is operating properly.
Lightning damage is not common. Nev-
ertheless, if you live in an area which
has severe electrical storms, we sug-
gest that you unplug your phone during
storms to reduce the possibility of dam-
age.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 26 Tuesday, August 31, 1999 10:01 PM
NOTES
26
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 27 Tuesday, August 31, 1999 10:01 PM
27
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1097a.fm Page 28 Tuesday, August 31, 1999 10:01 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/99
We Service What We Sell
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
08A99
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|