43-940.fm Page 1 Tuesday, April 25, 2000 1:04 PM
CID 940 Wireless
Caller ID System
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 3 Tuesday, April 25, 2000 1:04 PM
Troubleshooting .................................................................. 17
Care and Maintenance ........................................................ 18
The FCC Wants You to Know ........................................ 18
Lightning ........................................................................ 19
WARNING
: To reduce the risk of fire or shock hazard, do not
expose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT
OPEN.
!
CAUTION
: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER OR BACK. NO
USER-SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to the
presence of uninsulated dangerous voltage
within the product’s enclosure that might be
of sufficient magnitude to constitute a risk
of electric shock. Do not open the product’s
case.
This symbol is intended to inform you that
important operating and maintenance
instructions are included in the literature
accompanying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 4 Tuesday, April 25, 2000 1:04 PM
ˆ Features
Your RadioShack Wireless Caller ID System lets you screen
your phone calls, so you can decide whether or not to answer.
When you are up to 100 feet (30.48 meters) away from the
phone and you receive a call, the system’s transmitter instantly
sends the caller’s name and phone number (as provided by
your local telephone company to Caller ID service subscribers)
to its receiver.
Note:
In some cases, the local environment might affect the
transmission (for example, aluminum siding, electrical applianc-
es, computer equipment, and so on).
The system’s other features include:
Caller ID Memory
— stores up to 60 Caller ID records, so you
always know who called and when they called.
Out of Area Indication
— lets you know when an incoming call
is from an area code that does not send Caller ID information.
Support for Unlimited Receivers
— lets you add as many re-
ceivers as you need, anywhere within 100 feet of the transmit-
ter.
3-Line Liquid Crystal Display
— lets you see at a glance
whether you have a new call, along with the total number of
calls, the last caller’s name (if available) and phone number,
and the current time and date.
Page Button
— lets you verify that the receiver is within operat-
ing range of the transmitter.
4
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 5 Tuesday, April 25, 2000 1:04 PM
Rubber Duck Antenna
— rotates for the best reception in any
location.
Call Waiting Compatibility
— displays the Caller ID on Call
Waiting information when you use a Caller ID on Call Waiting-
equipped telephone or if your telephone is connected to a Caller
ID on a Call Waiting-equipped device.
Note:
When you have Call Waiting, the receiver displays the
caller’s name and number first, then CALLWAITINGappears,
and the two appear interchangeably afterwards.
Your system is ETL listed to UL standards and meets all appli-
cable FCC standards.
IMPORTANT INFORMATION
To use this system, you must be in an area where Caller ID ser-
vice is available, and you must subscribe to the service.
Where Caller ID is offered, one or more of the following options
are generally available:
• caller’s number only
• caller’s name only
• caller’s name and number
Note:
Your system displays the caller’s name only if that option
is available in your area.
5
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 6 Tuesday, April 25, 2000 1:04 PM
FCC INFORMATION
We have designed your system to conform to federal regula-
tions, and you can connect it to most telephone lines. However,
each system (and each device, such as a telephone or answer-
ing machine) that you connect to the telephone line draws pow-
er from the telephone line. We refer to this power draw as the
device’s ringer equivalence number, or REN. The REN is on the
bottom of the system.
If you use more than one telephone or other device on the line,
add up all the RENs. If the total is more than five (three in rural
areas), your telephone might not ring. If ringer operation is im-
paired, remove a device from the line.
Your system complies with Part 68 of FCC Rules. You must,
upon request, provide the FCC registration number and the
REN to your telephone company. Both numbers are on the bot-
tom of the system.
Note:
You must not connect your system to:
• coin-operated systems
• party-line systems
• most electronic key telephone systems
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 7 Tuesday, April 25, 2000 1:04 PM
This equipment complies with the limits for a Class B digital de-
vice as specified in Part 15 of FCC Rules. These limits provide
reasonable protection against radio and TV interference in a
residential area. However, your equipment might cause TV or
radio interference even when it is operating properly. To elimi-
nate interference, you can try one or more of the following cor-
rective measures:
• Reorient or relocate the TV or radio’s receiving antenna.
• Increase the distance between the equipment and the radio
or TV.
• Use outlets on different electrical circuits for the equipment
and the radio or TV.
Consult your local RadioShack store if the problem continues.
7
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 8 Tuesday, April 25, 2000 1:04 PM
ˆ Preparation
POWERING THE SYSTEM’S TRANSMITTER
Use the supplied 9V, 200-mA AC adapter to power the system’s
transmitter.
Cautions:
You must use a Class 2 power source that sup-
plies 9V DC and delivers at least 200 mA. Its cen-
ter tip must be set to positive and its plug must fit
!
DC 9V
the transmitter's
jack. The supplied adapter meets
these specifications. Using an adapter that does not meet
these specifications could damage the transmitter or the
adapter.
• Always connect the AC adapter to the transmitter before
you connect it to AC power. When you finish, disconnect
the adapter from AC power before you disconnect it from
the transmitter.
Plug the adapter’s barrel plug into the
DC 9V
transmitter’s
jack.
DC 9V
Plug the adapter’s other end into a
standard AC outlet. The POWER indi-
cator lights.
8
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 9 Tuesday, April 25, 2000 1:04 PM
POWERING THE SYSTEM’S RECEIVER
You can power the system’s receiver using four C batteries or
an AC adapter (neither supplied).
Installing Batteries
The system’s receiver can use four C batteries (not supplied)
for power. For longest operation and best performance, we rec-
ommend alkaline batteries, available at your local RadioShack
store.
Cautions:
• Always use fresh batteries of the required size and recom-
mended type.
• Do not mix old and new batteries, different types of batter-
ies (standard, alkaline, or rechargeable), or rechargeable
batteries of different capacities.
Follow these steps to install batteries.
1. Use a Phillips screwdriver to remove the screws on the bat-
tery compartment cover, then lift and remove the cover.
2. Place the batteries in the compartment as indicated by the
polarity symbols (+ and –) marked inside.
3. Replace the cover and secure it with the screws. ID TO
LEARNappears.
When the display dims or
appears, replace the batteries.
9
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 10 Tuesday, April 25, 2000 1:04 PM
Warning:
Dispose of old batteries promptly and properly. Do
not burn or bury them.
Caution:
If you do not plan to use the receiver with batteries for
a month, remove the batteries. Batteries can leak chemicals
that can destroy electronic parts.
Using AC Power
You can also power the system’s receiver using an optional 9V,
200-mA AC adapter and a size M AdaptaplugTM adapter (avail-
able at your local RadioShack store).
Cautions:
You must use a Class 2 power source that sup-
plies 9V DC and delivers at least 200 mA. Its cen-
ter tip must be set to positive and its plug must fit
!
DC 9V
the receiver's
jack. Using an adapter that does not
meet these specifications could damage the receiver or the
adapter.
• Always connect the AC adapter to the receiver before you
connect it to AC power. When you finish, disconnect the
adapter from AC power before you disconnect it from the
receiver.
1. Insert the Adaptaplug into the adapter’s cord so it reads
+
TIP .
DC 9V
2. Insert the Adaptaplug into the receiver’s
jack.
3. Plug the adapter into a standard AC outlet. IDTOLEARN
appears.
10
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 11 Tuesday, April 25, 2000 1:04 PM
CONNECTING THE SYSTEM
The system’s transmitter connects to any modular phone jack
and your phone. You can also connect it to an answering ma-
chine.
Note:
To insure proper operation, always connect the system’s
transmitter directly to a wall jack.
Connecting to a Single-Line Phone
1. Disconnect the line cord from
your phone and plug it into the
LINE-IN
LINE-OUT
LINE-IN
transmitter’s
jack. Be
sure the other end of the line
cord is directly connected to a
wall jack.
2. Plug one end of the supplied
line cord into the transmitter’s
LINE-OUT
jack.
3. Plug the other end of the cord into the phone’s jack.
Connecting to an Answering Machine
1. Plug a telephone line cord from the phone line into the
LINE-IN
transmitter’s
jack. Be sure the other end of the line
cord is directly connected to a wall jack.
2. Plug one end of the supplied line cord into the transmitter’s
LINE-OUT
jack and plug the cord’s other end into the
answering machine’s line jack.
11
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 12 Tuesday, April 25, 2000 1:04 PM
3. Plug a third line cord into the answering machine’s phone
jack and the telephone’s modular jack.
4. Set your answering machine to answer after two or more
rings. This gives the system time to record the call informa-
tion that the phone company sends between the first and
second rings.
SETTING THE SYSTEM’S
IDENTIFICATION CODE
You can install multiple receivers. Each receiver that you install
must be set with the same identification code as the transmitter.
Follow these steps to set the code.
Note:
PAGE
for 5 seconds or longer, the trans-
If you hold down
mitter’s identification code changes. Be sure to set all receivers
to the new code.
1. Place the receiver next to the transmitter.
SET
2. Hold down
on the receiver for about 5 seconds.
WAITING IDappears.
PAGE
3. Press
on the transmitter within 10 seconds after
WAITINGIDappears. This sends the transmitter identifi-
cation code to the receiver. The receiver beeps and ID
SETappears, indicating that the ID code is set.
CHECKING THE RANGE
1. Place the receiver at the desired location.
PAGE
2. Press
on the transmitter.
Preparation
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 13 Tuesday, April 25, 2000 1:04 PM
If the receiver is within the range, it beeps and PAGED
appears for 30 seconds.
If PAGEDdoes not appear, move the receiver closer to the
PAGE
transmitter and press
again. If it still does not beep,
repeat the steps under “Setting the System’s Identification
Code” on Page 12 to verify that the identification code is
properly set.
The receiver checks the range every three hours. If the receiver
is out of the range of the transmitter, OUTOFRANGEappears.
PAGE
Move the receiver closer to the transmitter and press
to
check the range again.
Note:
The transmitter can support an unlimited number of re-
ceivers. The distance between receivers should be 2 feet or
more to avoid interference.
SETTING THE DISPLAY CONTRAST, ALERT
TONE, AND CLOCK DISPLAY FORMAT
SET
DOWN
for about 5 seconds until
1. Hold down
and 9
SETTINGSappears.
DOWN
2. Press 9
to set the display contrast (the default set-
ting is 2).
SET
3. Repeatedly press
to select the contrast level (1–4),
. The current tone setting appears.
(The default setting is BEEPOFF.)
DOWN
then press 9
SET
4. Press
to toggle between BEEP ON and BEEP OFF,
DOWN
then press 9
format setting (the default setting is a 12-hour format).
. The display shows the current clock
13
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 14 Tuesday, April 25, 2000 1:04 PM
SET
5. Press
to toggle between the 12- and 24-hour formats,
DOWN
then press 9
. Setup is complete.
When you first connect the receiver, the clock displays
12:00PMand the date 1/01. When the first call comes in, the
current time and date are automatically set from the Caller ID
information provided by your phone company.
ˆ Operation
RECEIVING AND STORING CALLS
Caller ID is a service provided by your telephone company.
When you subscribe to this service, the telephone company
sends the caller’s telephone number (and name, if available)
and the call’s date and time between the first and second rings.
The system receives and displays this information for each call
and updates the display with the current date and time. If the
caller’s name has more than 15 characters, only the first 15
characters appear. Your system saves up to 60 call records,
then replaces the oldest call record with each new one.
REVIEWING CALL RECORDS
Each time you receive a call, the system saves a call record in
memory and NEWappears. Each call record includes the time
and date of the call, the call number (the order in which the call
was received), the caller’s telephone number, and the caller’s
name (if available).
14
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
To scroll through the call records, repeatedly press 9
43-940.fm Page 15 Tuesday, April 25, 2000 1:04 PM
DOWN
to
to see the old-
UP
see the newer records. Repeatedly press 8
er records.
Notes:
• If you do not press a button within about 10 seconds, the
system automatically returns to the time and date display.
• If no call information is stored, NOCALLappears when you
DOWN
press 9
.
• After you review all calls, ENDOFLISTappears.
• After you review a new call, NEWdisappears.
Displayed Call Information
The system can display the following information.
Display
Description
You have received a second call from the
same phone number.
RPT
The caller chose not to send the Caller ID
name and number.
PRIVATE
UNKNOWN
The caller is not within a Caller ID service
area.
MESSAGEWAITING A message is waiting. (Only appears if
or
you subscribe to your phone company’s
message waiting service.)
Appears when you receive a new call.
Operation
NEW
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 16 Tuesday, April 25, 2000 1:04 PM
Display
Description
The total number of incoming calls.
TOTAL
No call information is stored in the sys-
tem.
NO CALL
DELETING CALLS
Deleting a Single Call
DOWN
UP
until you see the call
Repeatedly press 9
or 8
DELETE
record you want to delete, then press
. The receiver de-
letes the selected call record and renumbers the remaining
records. After about 10 seconds, the clock display appears.
Deleting All Calls
DOWN
UP
Press 9
or 8 until a call record appears, then hold
DELETE
down
for about 5 seconds. The receiver beeps,
00NEW00TOTALappears briefly, then the clock display ap-
pears.
Note:
When using multiple receivers with the system, deleting
all call records from one receiver deletes the Caller ID informa-
tion for only that receiver. Any other receivers attached to the
system retain all Caller ID information.
16
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 17 Tuesday, April 25, 2000 1:04 PM
ˆ Troubleshooting
If your system is not working as it should, these suggestions
might help you eliminate the problem. If you see a message that
you do not understand, see “Displayed Call Information” on
Page 15.
Problem
Solution
Blank screen
Install or replace the batteries.
Adjust the contrast level (see “Setting the Dis-
play Contrast, Alert Tone, and Clock Display
Format” on Page 13).
Order Caller ID service from your local tele-
phone company.
No dial tone on
phone attached to
the system
Check all of the connections to make sure
they are secure.
Check for correct installation.
Disconnect the system and reconnect the
phone to see if the phone works without the
system.
Incoming call with
no Caller ID infor-
mation
You answered the call before the system
received the call information. Wait until your
phone rings at least twice before answering a
call.
Set the receiver’s Caller ID identification code.
(See “Setting the System’s Identification
Code” on Page 12.)
17
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 18 Tuesday, April 25, 2000 1:04 PM
ˆ Care and Maintenance
To enjoy your Wireless Caller ID System for a long time:
• Keep the system dry. If it gets wet, wipe it dry immediately.
• Use and store the system only in normal temperature envi-
ronments.
• Handle the system gently and carefully. Don’t drop it.
• Keep the system away from dust and dirt.
• Wipe the system with a damp cloth occasionally to keep it
looking new.
Modifying or tampering with the system’s internal components
and void
can cause a malfunction and invalidate its warranty
your FCC authorization to operate it.
If your system is not per-
forming as it should, take it to your local RadioShack store for
assistance. If the trouble is affecting the telephone lines, the
phone company can ask you to disconnect your system until
you have resolved the problem.
THE FCC WANTS YOU TO KNOW
In the unlikely event that your system causes problems on the
telephone line, the telephone company can disconnect your
service. The telephone company normally attempts to notify you
in advance. If advance notice is not practical, the telephone
company notifies you as soon as possible and advises you of
your right to file a complaint with the FCC.
18
Care and Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 19 Tuesday, April 25, 2000 1:04 PM
Also, the telephone company can make changes to its lines,
equipment, operations, or procedures that could affect the oper-
ation of this system. The telephone company notifies you of
these changes in advance so you can take the necessary steps
to prevent interruption of your telephone service.
LIGHTNING
Your system has built-in protection circuits to reduce the risk of
damage from surges in telephone line and power line current.
These protection circuits meet or exceed the FCC require-
ments. However, lightning striking the telephone or power lines
can damage your system.
Lightning damage is not common. Nevertheless, if you live in an
area that has severe electrical storms, we suggest that you un-
plug your system during storms to reduce the possibility of dam-
age.
19
Care and Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
43-940.fm Page 20 Tuesday, April 25, 2000 1:04 PM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material
and workmanship under normal use for one (1) year from the date of purchase from
RadioShack company-owned stores and authorized RadioShack franchisees and
dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS
WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRAN-
TIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE
OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM IN-
CONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT
OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damages, so the above limita-
tions or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and
the RadioShack sales receipt as proof of purchase date to any RadioShack store.
RadioShack will, at its option, unless otherwise provided by law: (a) correct the de-
fect by product repair without charge for parts and labor; (b) replace the product
with one of the same or similar design; or (c) refund the purchase price. All re-
placed parts and products, and products on which a refund is made, become the
property of RadioShack. New or reconditioned parts and products may be used in
the performance of warranty service. Repaired or replaced parts and products are
warranted for the remainder of the original warranty period. You will be charged for
repair or replacement of the product made after the expiration of the warranty pe-
riod.
This warranty does not cover: (a) damage or failure caused by or attributable to
acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow
instructions, improper installation or maintenance, alteration, lightning or other inci-
dence of excess voltage or current; (b) any repairs other than those provided by a
RadioShack Authorized Service Facility; (c) consumables such as fuses or batter-
ies; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f)
costs of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell
12/99
RadioShack — A Division of
Tandy Corporation
43-940
04A00
Fort Worth, Texas 76102
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|