Q-See Q25DVR4ES User’s Manual
Q25DVR4ES
Economy Series
User Manual
Contact Us:
Q-See Products
8015 E. Crystal Dr
Anaheim, CA 92807
Website:
Customer Service:
Phone: 877-998-3440 x 538
Email: [email protected]
Tech Support:
Phone: 877-998-3440 x 539
Email: [email protected]
Fax:
714-998-3509
Rev 101207
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 1: DVR Features
ꢀ 4 Channel BNC Camera Input.
ꢀ 1 Channel BNC Video Output.
ꢀ Video Source Option: NTSC / PAL.
ꢀ Motion Detection with Sensitivity and Area Settings.
ꢀ Time Schedule Recording / Motion Triggered Recording.
ꢀ One ATA-100 Hard Disk Interface.
ꢀ USB 2.0 Back up to computer.
ꢀ With Remote Control & Removable Hard Drive Tray.
Chapter 2: Layout - 2.1 Front Panel
1. FUNCTION KEYS
2. REMOVABLE HARD DRIVE TRAY
3. SELECTION / DIRECTION KEYS
4. HDD LOCK
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 2: Layout - 2.2 Rear Panel
1. 1 X BNC VIDEO OUTPUT
2. FAN
3. 4 X BNC VIDEO INPUT
4. 12V DC POWER SUPPLY
5. USB 2.0 PORT
Chapter 2: Layout - 2.3 Remote Control
01. CH1
02. CH2
03. CH3
04. CH4
05. QUAD
Select or enlarge CH1
Select or enlarge CH2
Select or enlarge CH3
Select or enlarge CH4
Quad View
Rewind
06.
Play recording list
Forward
07.
08.
Record
09.
Pause
10.
Stop recording
11.
13. MENU
14. UP
15. SEL/Edit
16. DOWN
Enter or exit setup menu
Move up prompt
Modify item
Move down prompt
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 3: Installation - 3.1 Installing Hard Drive
NOTE: This package comes with a 250GB hard drive. You would follow these instructions if
you want or need to install a new hard drive.
1. Slide the HDD tray out of DVR body carefully.
2. Connect the power cord and data cable to hard disk drive carefully.
3. Insert the HDD tray into DVR body.
4. Lock the HDD tray.
Make sure the HDD is set as MASTER
.
CAUTION: Do not remove the cartridge while the DVR is on!
CAUTION: The wedge at the end of the cartridge handle must be fully inserted into the compartment;
otherwise the cartridge will not be able to insert into the DVR firmly, it could also cause damage by scraping the
body of the DVR.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 3: Installation - 3.2 Connecting Cameras and TV Monitor
There are 4 camera inputs and 1 video output with BNC connectors (Refer to Chapter 2: Layout-
2.2 Rear Panel).
1. Connect the camera cables from the camera to the 4 Video Inputs on the DVR.
2. Connect the 4 power feeds for the cameras to the power connectors on the cable near the
video ports of the DVR, connect the other end to the power supply and plug the power
supply into a surge protector.
3. Using the included RCA to BNC cable, connect the yellow RCA connector from the cable
to the RCA video in port on the TV, connect the silver BNC connector on the other end of
the cable to the BNC video out port on the back of the DVR.
NOTE: Refer to Chapter 10: Appendix-10.1 System Connection Diagram
Chapter 3: Installation - 3.3 Connecting Power Supply
Please only use the power adapter supplied with the DVR.
Connect the power cord to a surge protector or Uninterruptible
Power Supply.
Chapter 4: System Boot - 4.1 Detecting Installed Hard Drive
After connecting the power, the system
Checking HDD ……
will boot-up and detect the installed
MASTER…
hard drive.
On the Monitor it will show the hard
drive information.
Please refer to the hard drive manual to
configure hard drive as Master.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 4: System Boot - 4.2 Recovering Lost Data
RECOVER HDD?
04811-101735
(SELECT)YES/(MENU)NO
The system will automatically recover
lost data.
A Power Error can cause data to be
lost.
Chapter 4: System Boot - 4.3 Restore Recording Feature
Power Error Detected
Restore Hard Disk (Master) OK
Restore REC Mode…………OK
If a Power Error occurs during
recording process, the system will
automatically resume recording
after power is restored.
Chapter 4: System Boot - 4.4 Main Screen
10%
While the DVR is running, the monitor will
display the view from the cameras as well as
the following:
Upper left: Percentage of hard drive space
used.
Middle: Channel name (CH 1 through CH 4).
Bottom right: Date and Time.
Bottom left: Mode, Status, Hard Drive Info,
and Schedule Setting of the DVR.
Refer to 6.1 Start Recording
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.1 Setup Menu
MAIN MENU
CAMERA SELECT
RECORD SELECT
RESOLUTION
RECORD FRAME
RECORD QUALITY
SCHEDULE SET
MISCELLANEOUS MENU
HARD DISK SET
MOTION SET
1 2 3 4
1 2 3 4
EACH
25
>
Press [
menu;
Menu] to enter the setup
HIGH
Use [ Up] and [ Down] to
select item;
FACTORY RESET
Press [ Select] to modify settings
and [
Menu] to exit.
PRESS (UP DOWN), ENTER (SELECT)
PRESS (MENU) TO EXIT
Menu Directory
CAMERA SELECT
RECORD SELECT
RESOLUTION
RECORD FRAME
VIDEO QUALITY
SCHEDULE SET
MISCELLANEOUS MENU
HARD DISK SET
MOTION SET
MAIN
MENU
AUTO RECORD
PASSWORD ENABLE
PASSWORD CHANGE
COLOR SET
TIME SET
FACTORY RESET
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.2 Camera Select
The DVR system can display 4
camera feeds in one picture (Quad
Mode).
Users can configure which
camera is displayed.
Press [ Select] to modify
setting and press [ CH1], [
CH2], [ CH3],[ CH4] to set
each channel separately.
If the channel is disabled, the
system will display “OFF” on the
monitor.
Chapter 5: DVR Setup - 5.3 Record Select
Configure which channels are allowed to record.
Note: If no channels are selected, an error message will appear briefly on the screen
when record is selected.
Chapter 5: DVR Setup - 5.4 Record Mode
There are two modes of resolution for video recording:
1. Each Mode: The DVR compresses and records each video channel separately so
the user can enlarge a single channel to full screen display and still be recording on all
channels. You can also record on specific channels, for example, user can turn off the
record function of CH1 and CH2 and then the system will only record video on CH3 and
CH4.
Press [ CH1], [ CH2], [ CH3], [ CH4] to switch between channels when
playing back recorded video.
In Each Mode user can use the Loop Function.
Loop Function: When the system is in Live mode or Recording mode, press the
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
[QUAD] button and hold for three (3) seconds to make each video channel enlarge to
full screen.
The full screen will be displayed for three (3) seconds, including Quad view.
The Loop Function will continue until any button is pushed.
For example, [Stop] will stop the Loop function and may stop the recording depending
on Record Schedule Settings.
2. Quad Mode: The DVR will compress and record all 4 video channels into
one file, therefore user cannot enlarge a single channel to full screen in play back mode.
User can not use the video Loop Function in this mode.
Chapter 5: DVR Setup - 5.5 Recording Frame Rate
Recording frame rate will affect the movement of objects in recorded video. More frames
per second gives smoother movement and uses more hard disk space.
System default value is 30fps (frames per second) for NTSC (PAL is 25fps), which means
the system will record 30 frames per second shared by all cameras. User can set frame rate
for NTSC to 30,15,10,7,5,4,3,2,1 frames per second (PAL is 25,12,8,6,4,3,2,1)
Chapter 5: DVR Setup - 5.6 Recording Quality
There are three levels of recording quality, High, Normal, and Low.
Higher quality uses more hard drive space.
Record frame rate, record quality and available hard drive space will affect
the total recording time of the DVR system.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.7 Schedule Set
User can setup video recording method by Time, Motion Triggered and Continuous
Recording.
SCHEDULE SET
“-” No Recording.
“T” Continuous (System Default).
“A” Motion Triggered.
TTTAAATTTTTTAATTTTT AAT
│
│
│
│
│
│
│
│
12 15 18 21 24
│
0
3
6
9
[ ] Up / [ ]Down: To move the prompt.
[ ] Select: To select Method.
Numbers along bottom are hours of the day
PRESS (UP DOWN), ENTER (SELECT)
PRESS (MENU) TO EXIT
Chapter 5: DVR Setup - 5.8 Sub Menu-Auto Record
When the function is set to be “ON”, DVR will be awaked to record automatically
by schedule if DVR is without any manual operations in five minutes.
When you choose “OFF”, DVR will not record until you press the [RECORD]
button.
Chapter 5: DVR Setup - 5.9 Sub Menu-Password Enable
When this option is set to be “ON”, you will be required to enter the password if
you want to stop recording or enter menus.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.10 Sub Menu-Password Change
System default password: Press [ CH1] button six times.
User needs to enter six characters
for the password.
All keys can be used as password
key except the [
Menu] key,
CURRENT
NEW
PASSWORD : - - - - - -
PASSWORD : - - - - - -
which is used to exit.
Note: To Reset the DVR.
Press the [Pause] button 10 times.
Resetting the DVR restores all
values to system defaults and the
DVR will reboot.
CONFIRM PASSWORD : - - - - - -
Afterward the default password is
[ CH1] button 6 times.
Chapter 5: DVR Setup - 5.11 Sub Menu-Color Set
“HUE”: 0-99.
“SATURATION” : 0-99.
“CONTRAST” : 0-99.
“BRIGHTNESS” : 0-99.
Button function :
[ Up] [ Down]: moves the prompt.
[REW]: Increase Value.
[FWD]: Reduce Value.
[CH1-CH4, QUAD]: Select Channel.
[
Menu]: exit.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.12 Sub Menu-Time Set
TIME SET
To configure the DVR’s time:
2008/08/08 20:08:08
Press [ Up] and [ Down] to move
prompt.
PRESS (UP,DOWN), ENTER (SELECT)
PRESS (MENU) TO EXIT
Press [ Select] to modify.
Press [ Menu] to save and exit.
Chapter 5: DVR Setup - 5.13 Hard Disk Setup
OVERWRITE ENABLED:
HARD DISK SETUP
If you choose YES, recording continues and
OVERWRITE ENABLED
HDD SIZE
HDD USED
[YES]
120042MB
80865MB 77%
overwrites previous recordings when the hard
drive is full. If you choose NO, the recording
process stops when the hard drive is full.
HDD SIZE: This shows the size of the hard
drive installed in the DVR.
HDD FORMAT
HDD USED: This shows the space used up
on the master hard drive and the percentage
of hard drive space being used.
PRESS (UP, DOWN), ENTER (SELECT)
PRESS (MENU)
TO EXIT
HDD FORMAT:
If you format the hard drive, it will erase all the data on the hard drive.
Note: When you install a new hard drive in the DVR, please use this function to
format the hard drive.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.14 Motion Setup
MOTION RECORD TIME:
This number indicates how long the
MOTION SET
triggered recording lasts after the DVR
has been triggered by motion.
MOTION RECORD TIME:
MOTION ALARM TIME:
10
OFF
MOTION ALARM TIME:
MOTION SET
This number indicates how long the
buzzer inside the DVR will sound when a
motion event has been detected.
MOTION SET:
PRESS (UP, DOWN), ENTER (SELECT)
PRESS (MENU) TO EXIT
User needs to have video record method
set to Motion Trigger. (Refer to 5.7
Schedule Set)
MOTION SET
CHANNEL SENSITIVITY:
Press [ Select] to adjust sensitivity of
motion detection on each channel.
High (1----------9, OFF) Low
CHANNEL
CHANNEL
CHANNEL
CHANNEL
1
2
3
4
SENSITIVITY
SENSITIVITY
SENSITIVITY
SENSITIVITY
4
4
4
4
CHANNEL
CHANNEL
CHANNEL
CHANNEL
1
2
3
4
AREA SET
AREA SET
AREA SET
AREA SET
When it’s OFF, the channel cannot be
triggered by movement.
PRESS (UP, DOWN), ENTER (SELECT)
PRESS (MENU) TO EXIT
CHANNELAREA SET:
Press “ Select” to enter the sensitive area of each camera. The picture of the selected channel is
divided into 144(12*12) blocks, press [REW] to move left, press [FWD] to move right, press [UP] to move
up, press [DOWN] to move down, press [ Select] to set the block to being active or not.
When the block is transparent, it’s active to record. When the block is covered by shadow, it is not
active, and motion in this area will NOT be recorded.
Make sure Record Schedule is set to Motion for the times required.
After completing the “MOTION SETUP”, User can exit by clicking
and press [ Record] to start Motion Recording.
Menu],
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 5: DVR Setup - 5.15 NTSC/PAL Output Selection
Change the J10 jumper on the system board to select NTSC or PAL video output as
marked on the silkscreen of the system board.
NTSC/PAL Select
Chapter 5: DVR Setup - 5.16 Factory Reset
Press the [ SEL] Button to reload factory defaults, then the DVR will reboot, all
custom settings (including password) will be restored to default.
There is no confirming dialog box for this selection after you press [ SEL]
button, the system will just reboot!
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 6: Recording - 6.1 Start Recording
Press [ Record] to start recording (As set in 5.7 Schedule Set).
System will display information on Screen.
NOTE: Only EACH Mode can enlarge single channel to full screen display.
1
10%
3
R
R
R
R
2
4
8
6
5
7
QUAD REC [M] (T) 2008/07/01 16:22:30
1. Hard Drive Usage (Displayed as a percentage)
2. Recording Symbol (channel is currently recording)
3. Channel Name
4. Mode (QUAD or EACH)
5. Status (REC, Play, FF1, FF2, FF3, REW, PAUSE)
6. HD Info. ([M] Master Hard disk)
7. Schedule settings: (T) Continuous (A) Motion (-) No Recording
8. The time and date on the DVR
Chapter 6: Recording - 6.2 Stop Recording
Press [
Stop] and system will prompt you to input password if you have already
activated the password. If password option is disabled [
Stop] will not stop
recording.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 6: Recording - 6.3 Recording Time on Hard Drive
Estimated record time based on a 120GB Hard Drive (Quad Mode) Unit: Hour
System
PAL
Quality
HIGH
Frame Rate
25
70
12
6
1
20
15
12
146
194
243
291
388
485
1748
2330
2913
NORMAL
LOW
93
117
30
15
7
1
System
NTSC
Quality
HIGH
Frame Rate
20
15
12
58
78
97
117
155
194
251
1748
2330
2913
NORMAL
LOW
332
416
Estimated record time based on a 120GB Hard Drive (Quad Mode) in hours:
120 (G Byte) x 1024 (M Byte) x 1024 (K Byte)
Divided by:
15 (K Byte/frame) x 7 (frame/sec.) x 60 (sec.) x 60 (min.)
Estimated time would be 332 Hours
Chapter 7: Playback
Press [
Play] to play the last recording.
Note: The DVR will play the last recording which has not been previously
played until all recordings have been played.
“*” Marks un-played video recording.
During playback, press the [Menu] button to initiate the Time Search feature
then the system will list all recorded video clips from the hard drive.
Newest video will at the top of the list, press [FF] to change the select mode
and then press [ Up] and [ Down] to select start time or date to change.
Press [ Select] to edit time value.
Press [
Play] again to continue playing the video.
* 2008 /0 1 / 0 8 08 : 30 : 3 2 --- 2008/0 1 / 0 8 16 : 00 : 05
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
SEARCH TIME
1
2
2008/01/08 08:30:56
┅
2008/01/08 16:00:35
2008/01/08 15:50:20
2008/01/08 14:30:56
2008/01/08 14:15:30
2008/01/08 14:00:15
2008/01/08 13:55:37
2008/01/08 11:30:12
2008/01/08 10:15:30
2008/01/08 08:30:55
01 TIME
02 TIME
03 TIME
04 TIME
05 MOTION
06 MOTION
07 MOTION
08 MOTION
3
*
*
*
5
4
(UP,DOWN) MOVE
(PLAY) PLAY
(MENU) EXIT
(FF) SELECT MODE (SELECT) CHANGE
1. Start Time.
2. End Time.
3. TIME: Continuous record.
5. Un-played video recording.
4. MOTION: Motion Triggered event.
Chapter 8: USB DVR Access - 8.1 Program Installation
1. Put the USB Driver Program CD in your CD-ROM Drive.
2. Open CD directory.
3. Double click on “Set up”.
4. Run the install DVR Viewer program.
To Run the program Double click the program icon [
] on the desktop.
DVR Viewer will detect the hard drive automatically when user connects the USB
cable to PC.
NOTICE: If the hard drive isn’t detected, please restart and try the following:
1-Close the USB program window and remove the USB cable
2-Press [
] then reconnect the USB cable to the PC and try again.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 8: USB DVR Access - 8.2 Program buttons
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
1. DVR Event List
2. Capture one frame picture
3. Save DVR’s Recorded Video to PC
5. Load Video File Saved in PC
7. Play PC Video File
4. Configuration
6. Play DVR Video File
8. Channel Selection Keys
10. Fast backward
12. Play Backward
14. Play
9. Playing Scroll Bar
11. Previous Frame
13. Pause
15. Next Frame
16. Fast Forward
18. Exit
17. Volume Scroll Bar (not used by this unit)
Press
to open the event video list.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Press
to configure the DVR play/record system.
Press
Press
to print the picture of DVR’s playback
to play the video .
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 9: Specifications
DVR Specifications
ITEM
DESCRIPTION
NOTE
Video Format
NTSC / PAL
Operation System
None
STAND-ALONE
Camera Input Channel
4 channel Composite BNC
Video Output Channel
Display Frame Rate
1 channel Composite BNC
NTSC
PAL
120 frames/second
4 x 30 frames/second
4 x 25 frames/second
Quad Mode
100 frames /second
Max.30 fps (Quad)
Max.25 fps (Quad)
Each Channel =
Recording Frame Rate
(Quad)
NTSC
PAL
Quad Mode
Max. 30 frames/s
(Total)
NTSC
PAL
Recording Frame Rate
(Each Mode)
30 fps ÷ Number of Cameras
Each Channel =
Max. 25 frames/s
(Total)
25 fps ÷ Number of Cameras
Continuous, Time Schedule, Motion Triggered.
Record Mode
Resolution
NTSC 720 x 480
Display
PAL
NTSC 320 x 112, 640 x 224
PAL 320 x 136, 640 x 272
720 x 576
Quad 640 x 224 (total)
Each 640 x 224
Low : 12K Byte
Normal : 15K Byte
High : 20K Byte
ATA -100 Interface
Record
Video Compression Format
(Each Channel)
Modified Motion-JPEG
(12-20K bytes/frame)
HDD Support
Up to 500GB
120GB Hard drive @ 7 frames per second @ Normal Quality
(120*1024*1024 K byte) ÷ ( 7*15*60*60 ) = 332 Hours
Estimated Record Length
USB
For PC playback & backup
Included
USB 2.0
Remote Control
Method
Full Screen
Dimension ( L x W x H )
Time Date Event
YES
Search
12.25in * 5.25in * 3.25in
Camera Specifications
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 10: Appendix - 10.1 System Connection Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Chapter 10: Appendix - 10.2 DVR Accessories (included)
Q-SEE Product Warranty
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Q-See Q25DVR4ES User’s Manual
Thank you for choosing our products.
All of our products users have a conditional free warranty repair service for hardware within
12 months starting from purchase date, and a free exchange service within one month (valid for
manufacturing defects). Permanent upgrading service is provided for the software.
Liability Exclusions:
Any product malfunction, abnormalities in operation or damage caused by following reasons
are not within the free service scope of our company. Please select payable service.
(1) Equipment damage caused by improper operation
(2) Improper environment and conditions in/on which the equipment operates, e.g., improper
power, environment temperature, humidity and lightening strike etc. that cause equipment damage.
(3) Damage caused by acts of nature: earthquake and fire etc.
(4) Equipment damage caused by the maintenance of personnel not authorized by our company.
(5) Product sold over 12 months ago.
In order to provide various services to you, please complete registration procedure after you
purchase the product. Cut off or copy User’s Information Card and fax or mail it to us after the
clicking on the Register link.
Customer Information Card
User’s Name
Company Name
Postal Address
Postal code
Mr./Mrs.
Phone Number
E-mail
Model Number
of Product
Serial Number
of Product
Purchase Date
Distributor
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
|