Model No. 831.28544.2
Serial No.
ELLIPTICAL EXERCISER
Serial
Number
Decal
User’s Manual
• Assembly
• Operation
• Maintenance
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manu-
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser. Use the ellipti-
cal exercise only as described in this
manual.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
11. Keep your back straight when using the ellip-
tical exerciser; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
14. The decal shown below has been placed on
the elliptical exerciser. If the decal is miss-
ing, or if it is not legible, please call toll-free
1-888-533-1333 and order a free replacement
decal. Apply the decal in the location shown.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothes when
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. Hold the handgrip pulse sensor or the han-
dlebars when mounting, dismounting, or
using the elliptical exerciser.
WARNING:
Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. Sears assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
®
Thank you for selecting the revolutionary PROFORM
HOME (1-800-469-4663). To help us assist you,
XP 130 elliptical exerciser. The XP 130 elliptical exer-
ciser provides a wide array of features designed to
make your workouts at home more effective and
enjoyable—and when you’re not exercising, the
unique XP 130 can be folded out of the away.
please note the product model number and serial
number before calling. The model number is
831.28544.2. The serial number can be found on a
decal attached to the elliptical exerciser (see the front
cover of this manual for the location of the decal).
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, call 1-800-4-MY-
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Handgrip Pulse Sensor
Console
Handlebar
Storage Magnet
Water Bottle Holder*
Wheel
Pedal
Pedal Arm Latch
Pedal Disk
Handle
Storage Latch
Leveling Foot
*No water bottle is included
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included allen wrenches, assembly requires a phillips screwdriver
, an adjustable
wrench
, and a rubber mallet
.
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST on page 25. The second number is the
quantity needed for assembly. Note: Some small parts may have been pre-assembled. If a part is not in the
parts bag, check to see if it has been pre-assembled. If a part is missing, call toll-free 1-888-533-1333.
M8 Split
M8 Washer
(88)–6
M8 Jamnut
(79)–5
M10 Nylon
Star Washer
(112)–8
Wave Washer
(111)–2
Locknut (81)–2
Washer (90)–3
M4 x 32mm
M4 x 16mm
Round Head
M4 x 45mm
Screw (108)–2
M4 x 14mm
Round Head
Screw (105)–6
Screw (104)–8
Screw (101)–8
M8 x 43mm Button
Bolt (78)–4
M8 x 23mm Shoulder
Screw (115)–4
M8 x 23mm Button
Hub Screw (87)–8
Screw (84)–4
M8 x 69mm Button
Bolt (80)–1
M10 x 80mm Carriage
Bolt (82)–2
M10 x 127mm Button Screw (83)–2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1. While another person lifts the Base (1), attach the
Front Stabilizer (6) to the Base with two M10 x 80mm
Carriage Bolts (82) and two M10 Nylon Locknuts (81).
1
82
81
6
81
1
2. Remove the indicated screw and bracket from the
Base (1). Discard the screw and the bracket.
2
Next, turn the Base Foot (26) into the Base (1) as far
as possible.
1
Bracket
26
Screw
7
3. Attach the Rear Stabilizer (7) to the Frame (2) with two
M10 x 127mm Button Screws (83).
3
83
Next, hold the handle on the Frame (2), press the
Latch Button (68), and lower the Frame until the Rear
Stabilizer (7) is resting on the floor.
Handle
2
68
4. Hold a Hub Cover (75) and a Crank Arm (36) against
the left Crank Hub (38). Align the holes in the Hub
Cover and the Crank Arm with the unused holes in the
left Crank Hub. Next, insert four Hub Screws (87) into
the Hub Cover and the Crank Arm, and finger tighten
the Hub Screws into the left Crank Hub. Tighten one of
the Hub Screws, and then tighten the Hub Screw
across from the first Hub Screw. Then, tighten the
remaining two Hub Screws.
4
43
36
98
38
36
75
Repeat this step on the right side of the elliptical exer-
ciser; make sure that the Crank Arms (36) are ori-
ented so the Crank Bushing Sleeves (43) are in the
positions shown. Note: there are no Pulley Screws
(98) on the right side.
87
87
43
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. While another person holds the Upright (3), connect
the Upper Wire Harness (48) to the Lower Wire
Harness (49). Gently pull the upper end of the
Upper Wire Harness to remove any slack, and
insert the Upright into the Base (1). Attach the Upright
with an M8 x 69mm Button Bolt (80), an M8 Split
Washer (90), and an M8 Jamnut (79). Do not tighten
the Button Bolt yet; make sure that the Jamnut is
in the hexagonal hole in the Base.
5
3
48
49
79
80
90
84
90
Next, finger tighten two M8 x 23mm Button Screws
(84) with M8 Split Washers (90) into the Base (1). Do
not tighten the Button Screws yet.
84
90
104
Attach the Water Bottle Holder (22) to the Base (1)
with two M4 x 14mm Screws (104).
22
1
6. Orient one of the Upright Covers (17) as shown, and hold
it against the Upright (3). Attach the Upright Cover with
two M4 x 16mm Round Head Screws (101). Attach the
other Upright Cover in the same way.
6
3
101
17
17
101
7. The Console (5) requires four 1.5V “D” batteries (not
included); alkaline batteries are recommended. Press
the two tabs on the battery cover, and remove the bat-
tery cover. Next, insert four batteries into the Console.
Make sure that the batteries are oriented as shown
by the diagrams inside of the battery compart-
ments. Then, reattach the battery cover to the Console.
7
Tabs
5
Battery
Cover
Batteries
8. While another person holds the Console (5) near the
Upright (3), connect the wire harness on the Console to
the Upper Wire Harness (48). Insert the excess wire
harness into the Upright. Next, attach the Console to
the Upright with four M4 x 16mm Round Head Screws
(101). Be careful to avoid pinching the wire har-
ness.
8
48
101
5
Wire
Harness
3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Identify the Left Handlebar (8) and the Left Upper Body
Arm (11), which are marked with stickers.
9
Orient the Left Handlebar (8) and the Left Upper Body
Arm (11) as shown, and insert the Left Handlebar into the
Left Upper Body Arm. Attach the Left Handlebar with two
M8 x 43mm Button Bolts (78) and two M8 Jamnuts (79).
Make sure that the Jamnuts are in the hexagonal
holes in the Left Upper Body Arm.
9
8
Attach the Right Handlebar (9) to the Right Upper Body
Arm (12) in the same way.
79
78
79
78
12
11
10. Insert the Pivot Axle (74) into the Upright (3) and center
it. Apply a generous amount of the included grease to
the Pivot Axle.
10
88
3
84
111
Orient the Left Upper Body Arm (11) as shown, and
slide it onto the left end of the Pivot Axle (74). Slide the
Right Upper Body Arm (12) onto the right end of the
Pivot Axle.
Grease
11
74
12
88
Tighten an M8 x 23mm Button Screw (84) with an M8
Washer (88) and a Wave Washer (111) into each end of
the Pivot Axle (74). Make sure that the Wave Washers
are on the ends of the Pivot Axle.
111
105
84
11
11. Hold the Left Front Handlebar Cover (18) and the Left
Rear Handlebar Cover (19) around the Left Upper Body
Arm (11). Attach the Handlebar Covers with three M4 x
32mm Round Head Screws (105).
20
21
Attach the Right Front Handlebar Cover (20) and the
Right Rear Handlebar Cover (21) around the Right
Upper Body Arm (12) in the same way.
12
18
11
19
8
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Identify the Left Pedal (13) and the Left Pedal Leg
(14), which are marked with stickers.
12
13
Attach the Left Pedal (13) to the Left Pedal Leg (14)
with an M4 x 45mm Screw (108), three M4 x 14mm
Screws (104), and four Star Washers (112).
Attach the Right Pedal (not shown) to the Right Pedal
Leg (not shown) in the same way.
112
108
112
112
104
14
112
104
13. Apply a thin film of grease to one of the Pedal Leg Axles
(32) and to the faces of the two Pedal Leg Bushings
(33) in the Left Pedal Leg (14).
13
Next, slide an M8 Washer (88) and a Pedal Leg Cover
(31) onto an M8 x 23mm Shoulder Screw (115), and
turn the Shoulder Screw a few turns into the Pedal Leg
Axle (32).
12
115
11
88
31
31
While another person holds the front end of the Left
Pedal Leg (14) inside of the bracket on the Left Upper
Body Arm (11), insert the Pedal Leg Axle (32) into both
parts. Next, slide an M8 Washer (88) and a Pedal Leg
Cover (31) onto another M8 x 23mm Shoulder Screw
(115), and turn the Shoulder Screw a few turns into the
Pedal Leg Axle. Tighten both Shoulder Screws.
33
Grease
88
115
Grease
32
Repeat this step to attach the Right Pedal Leg (not
shown) to the Right Upper Body Arm (12).
14
14. Lift the latch on the underside of the Left Pedal Leg
(14), and set the Left Pedal Leg on the left Crank
Bushing Sleeve (43). Release the lever, and make sure
that the Left Pedal Leg is securely connected to the
Crank Bushing Sleeve.
14
14
Connect the Right Pedal Leg (not shown) in the same
way.
Latch
See step 5. Tighten the M8 x 69mm Button Bolt (80)
and the two M8 x 23mm Button Screws (84).
43
15. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO FOLD AND UNFOLD THE ELLIPTICAL
EXERCISER
HOW TO MOVE THE ELLIPTICAL EXERCISER
To move the elliptical exerciser, first fold it as
When the elliptical exerciser is not in use, the frame
can be folded out of the way. First, lift the latch under
each pedal leg, and lift the pedal legs off the sleeves
on the crank arms.
described at the left. Next, stand in front of the ellipti-
cal exerciser, hold the handle on the upright, and place
one foot against the center of the front stabilizer. Pull
the handle until the elliptical exerciser will roll on the
front wheels. Carefully move the elliptical exerciser to
the desired position, and then lower it.
Handle
Crank
Arm
Pedal Leg
Latch
Sleeve
Next, raise the pedal legs until they touch the magnets
on the upper body arms; the magnets will hold the
pedal legs in place. Then, hold the handle and lift the
frame until it locks in a vertical position.
Place
your foot
here
Pedal Leg
Magnet
Handle
HOW TO LEVEL THE ELLIPTICAL EXERCISER
If the elliptical exerciser rocks slightly on your floor
during use, turn one or both of the leveling feet
beneath the rear stabilizer until the rocking motion is
eliminated.
Frame
Latch
Button
To use the elliptical exerciser, first hold the handle,
press the latch button, and lower the frame.
Next, pull the pedal legs off the magnets on the upper
body arms. Then, lift the latches under the pedal
legs, and set the pedal legs on the sleeves on the
crank arms. Release the latches, and make sure that
the pedal legs are securely connected to the crank
arms.
Leveling
Feet
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lowest position.
Next, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion.
Handlebars
Note: The crank arms can turn in either direction.
It is recommended that you turn the crank arms in
the direction shown by the arrow at the right; how-
ever, for variety, you can turn the crank arms in the
opposite direction.
Pedals
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the highest
pedal first. Then, step off the lowest pedal.
Crank Arm
11
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES OF THE CONSOLE
The three resistance & rpm programs automatically
change the resistance of the pedals and prompt you to
vary your pedaling pace as they guide you through an
effective workout.
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable. When the manual mode of the console is
selected, you can change the resistance of the pedals
with the touch of a button. As you exercise, the con-
sole will provide continuous exercise feedback. You
can even monitor your heart rate using the handgrip
pulse sensor.
The console also features iFIT.com interactive technol-
ogy. Having iFIT.com technology is like having a per-
sonal trainer in your home. Using a stereo audio cable
(available at electronics stores), you can connect the
elliptical exerciser to your portable stereo, home stereo,
computer, or VCR and play special iFIT.com CD and
The console also offers a selection of preset programs. video programs (iFIT.com CDs and videocassettes are
The two calorie goal programs allow you to choose a
calorie-burning goal for your workout. As you exercise,
the console will count the calories that you burn until
the goal is reached.
available separately). iFIT.com programs automatically
control the resistance of the pedals and prompt you to
vary your pace as a personal trainer coaches you
through every step of your workout. High-energy music
provides added motivation. To purchase iFIT.com
CDs and videocassettes, call the toll-free tele-
phone number on the front cover of this manual.
The two pulse control programs automatically control
the resistance of the pedals and prompt you to
increase or decrease your pedaling pace to keep your
heart rate near a target heart rate setting during your
workout.
With the elliptical exerciser connected to your comput-
er, you can also go to our Web site at www.iFIT.com
and access programs directly from the internet.
Explore www.iFIT.com for more information.
The distance program counts the number of revolu-
tions that you pedal during your workout, until you
have completed 5,000 revolutions.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
To use the manual mode of the console, follow the
steps beginning on page 13. To use a calorie goal
program, see page 15. To use a pulse control pro-
gram, see page 15. To use the distance program,
see page 17. To use a resistance & rpm program,
see page 17. To use an iFIT.com CD or video pro-
gram, see page 21. To use an iFIT.com program
directly from our Web site, see page 22.
conserve the batteries. Press the Display Color
button repeatedly to select a color or to turn off
the backlighting.
The left side of the
display—The left side
of the display will
show the elapsed
time, the approximate
Note: If there is a sheet of clear plastic on the face of
the console, remove the plastic.
number of calories
you have burned, and
the approximate number of grams of carbs you
have burned. Note: When some preset programs
are selected, the display will show the time
remaining in the program instead of the elapsed
time. When a calorie goal program is selected,
the display will show the number of calories still to
be burned instead of the number of calories you
have burned.
HOW TO USE THE MANUAL MODE
Press the Resistance decrease button or
1
begin pedaling to turn on the console.
A moment after the console is turned on, the dis-
play will light.
The left side of the display will also show your
heart rate when you use the handgrip pulse sen-
sor (see step 5 on page 14).
Select the manual mode.
2
The center of the
Each time the console is turned on, the manual
mode will be selected automatically. If you have
selected a program or the iFIT.com mode, select
the manual mode by pressing the Programs but-
ton repeatedly until the display appears as shown
below.
display—When the
manual mode, a calo-
rie goal program, the
distance program, or
the iFIT.com mode is
selected, the center of
the display will show a track that represents 640
revolutions. As you exercise, the indicators around
the track will appear in succession until the entire
track appears. The track will then disappear and
the indicators will again begin to appear in suc-
cession.
The center of the display will also show the resis-
tance setting of the pedals for a few seconds each
time the resistance setting changes.
Begin pedaling and change the resistance of
3
the pedals as desired.
As you pedal, change
The right side of the
the resistance of the
display—The right
pedals by pressing
side of the display will
the Resistance
show the distance
increase and
(total revolutions) you
decrease buttons
have pedaled and
repeatedly. There are
your pedaling pace
ten resistance levels. Note: After the buttons are
pressed, it will take a moment for the pedals to
reach the selected resistance level.
(revolutions per minute [rpm]). Note: When the
distance program is selected, the display will
show the number of revolutions still to be pedaled
instead of the number of revolutions you have
pedaled.
Monitor your progress with the display.
4
Note: The display can be backlit with any of three
colors, or the backlighting can be turned off to
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Measure your heart rate if desired.
If there are thin
ful not to move your hands excessively or to
squeeze the metal contacts too tightly. For opti-
mal performance, clean the metal contacts using
a soft cloth; never use alcohol, abrasives, or
chemicals.
5
sheets of plastic on
the metal contacts
on the handgrip
Metal Contacts
Turn on the fan if desired.
pulse sensor, peel
off the plastic. To
measure your heart
rate, hold the hand-
grip pulse sensor,
with your palms rest-
6
7
To turn on the fan at low speed, press the Fan
button. To turn on the fan at high speed, press
the button a second time. To turn off the fan,
press the button a third time. Note: If the pedals
are not moved for a few minutes, the fan will
automatically turn off to conserve the batteries.
ing against the metal contacts. Avoid moving
your hands or gripping the contacts too
tightly.
Pivot the thumb tab
Thumb
Tab
on the right side of
the fan to adjust the
angle of the fan.
When your pulse is
detected, a heart-
shaped symbol will
flash in the left side
of the display each
time your heart
beats, one or two
When you are finished exercising, the console
will automatically turn off.
dashes will appear, and then your heart rate will
be shown. For the most accurate heart rate read-
ing, hold the contacts for at least 15 seconds.
Note: If you continue to hold the handgrip pulse
sensor, the display will show your heart rate for
up to 30 seconds. The display will then show your
heart rate along with the other modes.
If the pedals are not moved for several seconds, a
tone will sound and the console will pause.
If the pedals are not moved for about five min-
utes, the console will turn off and the display will
be reset.
If your heart rate is not shown, make sure that
your hands are positioned as described. Be care-
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A CALORIE GOAL PROGRAM
Press the Resistance decrease button or
HOW TO USE A PULSE CONTROL PROGRAM
Press the Resistance decrease button or
1
1
begin pedaling to turn on the console.
begin pedaling to turn on the console.
A moment after the console is turned on, the dis-
play will light.
A moment after the console is turned on, the dis-
play will light.
Select one of the calorie goal programs.
Select one of the pulse control programs.
2
3
2
Press the Programs
button repeatedly
until “P 1” or “P 2”
and a goal of 300
calories or 500 calo-
ries appear in the dis-
play.
Press the Programs
button repeatedly until
“P 3” or “P 4” appears
in the right side of the
display.
If pulse control pro-
gram 3 is selected, a
profile of the target
heart rate settings of
the program will scroll
across the center of
the display.
Begin pedaling to start the program.
When a calorie goal program is used, the console
will function in the same way as when the manual
mode is selected, except the left side of the dis-
play will show the number of calories still to be
burned instead of the number of calories you
have burned. When the calorie goal is reached, a
tone will sound and the time will stop incrementing
in the display.
If pulse control pro-
gram 4 is selected, a
pulse symbol will
appear in the center
of the display. Each
When you are finished exercising, the console
will automatically turn off.
4
time a heartbeat is
detected while you
are using the handgrip pulse sensor, the pulse
symbol will reappear.
See step 7 on page 14.
Enter a target heart rate setting.
3
If pulse control pro-
gram 3 is selected,
the maximum target
heart rate setting of
the program will flash
in the display. If
desired, press the
Resistance increase and decrease buttons to
change the maximum target heart rate setting
(see EXERCISE INTENSITY on page 24). If you
change the maximum target heart rate setting,
the intensity level of the entire program will
change.
If pulse control program 4 is selected, the tar-
get heart rate setting for the program will flash in
the display. If desired, press the Resistance
increase and decrease buttons to change the tar-
get heart rate setting (see EXERCISE INTENSI-
TY on page 24).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Hold the handgrip pulse sensor.
After the first minute of the program, the Pace
Coach will prompt you to maintain a consistent
pedaling pace. When one of the “Too Slow”
arrows lights, increase your pace. When the one
of the “Too Fast” arrows lights, decrease your
pace. When the center indicator lights, maintain
your current pace.
4
5
It is not necessary to hold the handgrip pulse
sensor continuously during a pulse control pro-
gram; however, you should hold the handgrip
pulse sensor frequently for the program to oper-
ate properly. Each time you hold the handgrip
pulse sensor, keep your hands on the metal
contacts for at least 30 seconds.
Begin pedaling to start the program.
Pulse control program 3 is divided into 30 one-
minute segments. One target heart rate setting is
programmed for each segment. Note: The same
target heart rate setting may be programmed for
two or more consecutive segments.
Important: The target heart rate settings are
intended only to provide motivation. Your
actual heart rate may be slower than the tar-
get heart rate settings. Make sure to exercise
at a pace that is comfortable for you.
The target heart rate
Current Segment
setting for the first
segment will be
shown in the flashing
Current Segment col-
umn in the center of
the display. The tar-
Note: During the program, you can manually over-
ride the resistance setting for the current seg-
ment, if desired, by pressing the increase and
decrease buttons. However, when the console
compares your heart rate to the target heart rate
setting, the resistance of the pedals may auto-
matically increase or decrease to bring your heart
rate closer to the target heart rate setting.
get heart rate settings for the next four segments
will be shown in the columns to the right.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a
series of tones will sound, and all target heart
rate settings will move one column to the left.
The target heart rate setting for the second seg-
ment will then be shown in the flashing Current
Segment column.
If you stop pedaling for several seconds, a tone
will sound and the program will pause. To restart
the program, simply resume pedaling.
Monitor your progress with the display.
See step 4 on page 13.
6
7
8
Pulse control program 4 is divided into 40 one-
minute segments. The same target heart rate set-
ting is programmed for all segments. Note: For a
shorter workout, stop exercising or select a differ-
ent program before the program ends.
Turn on the fan if desired.
See step 6 on page 14.
When you are finished exercising, the console
will automatically turn off.
During both pulse control programs, the con-
sole will regularly compare your heart rate to the
target heart rate setting. If your heart rate is too
far below or above the target heart rate setting,
the resistance of the pedals will automatically
increase or decrease to bring your heart rate
closer to the target heart rate setting.
See step 7 on page 14.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE DISTANCE PROGRAM
Press the Resistance decrease button or
HOW TO USE A RESISTANCE & RPM PROGRAM
Press the Resistance decrease button or
1
1
begin pedaling to turn on the console.
begin pedaling to turn on the console.
A moment after the console is turned on, the dis-
play will light.
A moment after the console is turned on, the dis-
play will light.
Select the distance program.
Select one of the resistance & rpm programs.
2
3
2
Press the Programs
button repeatedly until
“P 5” and a goal of
5,000 revolutions
Press the Programs
button repeatedly until
“P 6,” “P 7,” or “P 8”
appears in the right
appear in the display.
side of the display.
When a resistance &
rpm program is select-
ed, a profile of the resistance settings of the pro-
gram will scroll across the center of the display.
The left side of the display will show how long the
program will last.
Begin pedaling to start the program.
When the distance program is used, the console
will function in the same way as when the manual
mode is selected, except the right side of the dis-
play will show the number of revolutions still to be
pedaled instead of the number of revolutions you
have pedaled. When the calorie goal is reached, a
tone will sound and the time will stop incrementing
in the display.
Begin pedaling to start the program.
3
Each program is divided into several one-minute
segments. One resistance setting and one pace
setting are programmed for each segment. Note:
The same resistance setting and/or pace setting
may be programmed for two or more consecutive
segments.
When you are finished exercising, the console
will automatically turn off.
4
The resistance setting
See step 7 on page 14.
Current Segment
for the first segment
will be shown in the
flashing Current
Segment column in
the center of the dis-
play. (Note: The pace
settings are not shown in the display.) The resis-
tance settings for the next four segments will be
shown in the columns to the right.
As you exercise, the Pace Coach will help you to
keep your pedaling pace near the pace setting for
the current segment. When one of the “Too Slow”
arrows lights, increase your pace. When the one
of the “Too Fast” arrows lights, decrease your
pace. When the center indicator lights, maintain
your current pace.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: The pace settings are intended
only to provide motivation. Your actual pace
may be slower than the pace settings. Make
sure to exercise at a pace that is comfortable
for you.
desired, by pressing the increase or decrease but-
ton. However, when the next segment begins, the
resistance will change if a different resistance set-
ting is programmed for the next segment.
If you stop pedaling for several seconds, a tone
will sound and the program will pause. To restart
the program, simply resume pedaling.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash, a
series of tones will sound, and all resistance set-
tings will move one column to the left. The resis-
tance setting for the second segment will then be
shown in the flashing Current Segment column,
and the resistance of the pedals will change to the
resistance setting for the second segment. Note: If
all of the indicators in the Current Segment col-
umn are lit after the resistance settings have
moved to the left, the resistance settings may
move downward so only the highest indicators
appear in the matrix.
Monitor your progress with the display.
See step 4 on page 13.
4
5
6
7
Measure your heart rate if desired.
See step 5 on page 14.
Turn on the fan if desired.
See step 6 on page 14.
The program will continue until the resistance
setting for the last segment is shown in the
Current Segment column and the last segment
ends.
When you are finished exercising, the console
will automatically turn off.
See step 7 on page 14.
Note: During the program, you can override the
resistance setting for the current segment, if
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT YOUR CD PLAYER, VCR,
OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
1/8” LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the elliptical exerciser must be
connected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages 19
and 20 for connecting instructions. To use iFIT.com
videocassettes, the elliptical exerciser must be connect-
ed to your VCR. See page 21 for connecting instruc-
tions. To use iFIT.com programs directly from our
Web site, the elliptical exerciser must be connected to
your computer. See page 20.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the cable
into the AUDIO OUT jack on your stereo.
A/B
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
LINE OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
A. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your CD player.
Plug your headphones into the PHONES jack.
B. See the drawing above. Plug one end of a 1/8” to
1/8” stereo audio cable (available at electronics
stores) into the jack beneath the console. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
C. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your stereo. Plug your headphones into the
other side of the Y-adapter.
Head-
phones
Audio
Cable
B. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your CD player. Plug your headphones into the
other side of the Y-adapter.
C
PHONES
1/8”
Audio
Cable
Y-adapter
B
PHONES
PHONES
Headphones
1/8”
Audio
Y-adapter
Cable
Headphones
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 1/8” LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your stereo.
A. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the LINE OUT jack on your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
LINE OUT
Audio
Cable
Audio
Cable
B. Plug one end of a 1/8” to 1/8” stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into a 1/8” Y-adapter (available at electronics
stores). Plug the Y-adapter into the PHONES jack
on your computer. Plug your headphones or speak-
ers into the other side of the Y-adapter.
B. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack beneath
the console. Plug the other end of the cable into an
RCA Y-adapter (available at electronics stores).
Next, remove the wire that is currently plugged into
the LINE OUT jack on your stereo and plug the wire
into the unused side of the Y-adapter. Plug the Y-
adapter into the LINE OUT jack on your stereo.
B
B
PHONES
CD
VCR
Audio
1/8”
Amp
LINE OUT
Cable
Y-adapter
RCA
Headphones/Speakers
Audio
Y-adapter
Cable
Wire removed from
LINE OUT jack
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE AN IFIT.COM CD OR VIDEO
PROGRAM
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 20.
To use an iFIT.com CD or video program, the elliptical
exerciser must be connected to your CD player or
VCR. See HOW TO CONNECT YOUR CD PLAYER,
VCR, OR COMPUTER on pages 19 to 21. To pur-
chase iFIT.com CDs or videocassettes, call the toll-
free telephone number on the front cover of this
manual.
A. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into the AUDIO OUT jack on your VCR.
Follow the steps below to use an iFIT.com CD or
video program.
A
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
Press the Resistance decrease button or
1
AUDIO OUT
begin pedaling to turn on the console.
RIGHT
LEFT
A moment after the console is turned on, the dis-
play will light.
Audio
Cable
Select the iFIT.com mode.
2
To select the iFIT.com
mode, press the
Programs button
repeatedly until the
track and the letters
“iFIT” appear in the
display.
B. Plug one end of a 1/8” to RCA stereo audio cable
(available at electronics stores) into the jack
beneath the console. Plug the other end of the
cable into an RCA Y-adapter (available at electron-
ics stores). Next, remove the wire that is currently
plugged into the AUDIO OUT jack on your VCR
and plug the wire into the unused side of the Y-
adapter. Plug the Y-adapter into the AUDIO OUT
jack on your VCR.
Press the Play button on your CD player or
3
VCR.
Note: If you are using an iFIT.com CD, insert the
CD into your CD player; if you are using an
iFIT.com videocassette, insert the videocassette
into your VCR.
B
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
OUT
A moment after the play button is pressed, your
personal trainer will begin guiding you through
your workout. Simply follow your personal trainer’s
instructions.
RCA
Y-adapter
Audio Cable
The program will function in almost the same way
as a resistance & rpm program (see step 3 on
page 17). However, an electronic “chirping” sound
will alert you when the resistance setting and/or
pace setting is about to change.
Wire removed from
AUDIO OUT jack
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If the resistance of the pedals and/or the
pace setting does not change when a “chirp”
is heard:
Select the iFIT.com mode.
2
See step 2 on page 21.
• Make sure that the letters “iFIT” appear in
the display.
Go to your computer and start an internet
connection.
3
4
5
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
Start your Web browser, if necessary, and go
to our Web site at www.iFIT.com.
Follow the desired links on our Web site to
select a program.
• Make sure that the audio cable is properly
connected and that it is fully plugged in.
Read and follow the on-line instructions for using
a program.
Monitor your progress with the display.
See step 4 on page 13.
4
5
6
7
Follow the on-line instructions to start the
program.
6
7
Measure your heart rate as desired.
See step 5 on page 14.
When you start the program, an on-screen count-
down will begin.
Turn on the fan if desired.
See step 6 on page 14.
Return to the elliptical exerciser and begin
pedaling.
When the on-screen countdown ends, the pro-
gram will begin. The program will function in
almost the same way as a resistance & rpm pro-
gram (see step 3 on page 17). However, an elec-
tronic “chirping” sound will alert you when the resis-
tance setting and/or pace setting is about to
change.
When you are finished exercising, the console
will automatically turn off.
See step 7 on page 14.
Monitor your progress with the display.
See step 4 on page 13.
8
HOW TO USE AN IFIT.COM PROGRAM
DIRECTLY FROM OUR WEB SITE
Measure your heart rate if desired.
See step 5 on page 14.
9
Our Web site at www.iFIT.com allows you to play
iFIT.com programs directly from the internet. To use
programs from our Web site, the elliptical exerciser
must be connected to your home computer. See HOW
TO CONNECT YOUR COMPUTER on page 20. In
addition, you must have an internet connection and an
internet service provider. A list of specific system
requirements is found on our Web site.
Turn on the fan if desired.
10
11
See step 6 on page 14.
When you are finished exercising, the con-
sole will automatically turn off.
Follow the steps below to use a program from our
Web site.
See step 7 on page 14.
Press the Resistance decrease button or
1
begin pedaling to turn on the console.
A moment after the console is turned on, the dis-
play will light.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands while using the handgrip
pulse sensor. Excessive movement may interfere
with heart rate readings.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. Important: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
• Do not hold the metal contacts too tightly; doing so
may interfere with heart rate readings.
BATTERY REPLACEMENT
• For the most accurate heart rate reading, hold the
metal contacts for about 30 seconds.
If the console displays become dim, the batteries
should be replaced; most console problems are the
result of low batteries. See assembly step 7 on page
7 for replacement instructions.
• For optimal performance of the handgrip pulse sen-
sor, keep the metal contacts clean. The contacts
can be cleaned with a soft cloth—never use alco-
hol, abrasives, or chemicals.
HOW TO LEVEL THE ELLIPTICAL EXERCISER
HOW TO ELIMINATE FLEXING IN THE CENTER OF
THE ELLIPTICAL EXERCISER
If the elliptical exerciser rocks slightly on your floor
during use, turn one or both of the leveling feet
beneath the rear stabilizer until the rocking motion is
eliminated.
If the elliptical exerciser flexes in the center during
use, turn the base foot (see the drawing at the left)
until the flexing is eliminated.
Base
Foot
Leveling
Feet
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
WARNING:
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for ener-
gy. Only after the first few minutes of exercise does
your body begin to use stored fat calories for energy.
If your goal is to burn fat, adjust the intensity of your
exercise until your heart rate is near the lowest num-
ber in your training zone as you exercise.
Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over the age of 35
or persons with pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
For maximum fat burning, adjust the intensity of your
exercise until your heart rate is near the middle num-
ber in your training zone as you exercise.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exer-
cise is activity that requires large amounts of oxygen
for prolonged periods of time. This increases the
demand on the heart to pump blood to the muscles,
and on the lungs to oxygenate the blood. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone as you exercise.
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition
and adequate rest are essential for successful results.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning, maximum fat
burning, and cardiovascular (aerobic) exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training zone exercise, consisting of 20 to 30 min-
utes of exercising with your heart rate in your training
zone. Note: During the first few weeks of your exer-
cise program, do not keep your heart rate in your
training zone for longer than 20 minutes.
To find the proper heart rate for you, first find your age
at the bottom of the chart (ages are rounded off to the
nearest ten years). Next, find the three numbers above
your age. The three numbers are your “training zone.”
The lower two numbers are recommended heart rates
for fat burning; the highest number is the recommend-
ed heart rate for aerobic exercise.
A cool-down, with 5 to 10 minutes of stretching. This
will increase the flexibility of your muscles and will
help to prevent post-exercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relative-
ly low intensity level for a sustained period of time.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.28544.2
R0606A
Key
Key
Key
No. Qty. Description
No. Qty. Description
No. Qty. Description
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
2
1
Base
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
2
4
2
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
1
1
1
1
1
1
2
1
2
2
2
4
7
1
4
2
Crank Bushing Cover
Crank Bushing
Crank Bushing Sleeve
Crank Bearing Set
Crank
84
85
4
1
M8 x 23mm Button
Frame
Screw
3
Upright
M6 x 10mm Button
Screw
4
Upright Endcap
Console
5
86
87
2
8
Crank Screw
6
Front Stabilizer
Rear Stabilizer
Left Handlebar
Right Handlebar
Handlebar Endcap
Left Upper Body Arm
Right Upper Body Arm
Left Pedal
Crank Spacer
Crank Snap Ring
Upper Wire Harness
Lower Wire Harness
Reed Switch/Wire
Belt
Hub Screw
7
88 10
M8 Washer
8
89
2
M10 x 60mm Button
Screw
9
10
11
12
13
14
15
16
17
18
90
91
3
1
1
1
4
1
1
1
4
2
2
8
M8 Split Washer
Flywheel Spacer
Flywheel Washer
Flywheel Snap Ring
Pillow Block Screw
Stop Screw
Flywheel
92
“C” Magnet
93
Left Pedal Leg
Right Pedal
Pillow Block
94
Magnet
95
Right Pedal Leg
Upright Cover
Left Front Handlebar
Cover
Spring
96
M8 x 35mm Screw
“E” Clip
Idler
97
Idler Bracket
Clamp
98
Pulley Screw
99
Crank Washer
M4 x 25mm Screw
M4 x 16mm Round
Head Screw
19
20
21
1
1
1
Left Rear Handlebar
Cover
Reed Switch Bracket
Base Pin
100
101
Right Front Handlebar
Cover
Latch Bracket Spacer
Hairpin Cotter Pin
Latch Bracket
Pivot Bracket
Pivot Bracket Spacer
Frame Pin
102
4
Motor Washer
M4 x 16mm Screw
M4 x 14mm Screw
M4 x 32mm Round
Head Screw
Right Rear Handlebar
Cover
103 23
104
105
8
6
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
2
2
1
2
1
1
6
4
2
4
1
2
2
2
2
1
1
Water Bottle Holder
Front Stabilizer Endcap 67
Rear Stabilizer Endcap
Wheel
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
Latch Button
Roll Pin
106
107
2
M8 x 31mm Shoulder
Screw
Base Foot
Motor
4
2
2
2
2
8
1
1
4
M4 x 12mm Screw
M4 x 45mm Screw
Large Wave Washer
M8 Small Washer
Wave Washer
Star Washer
Leveling Foot
Left Side Shield
Right Side Shield
Upper Body Bushing
Pedal Leg Cover
Pedal Leg Axle
Pedal Leg Bushing
Base Axle
Resistance Cable Pulley 108
Resistance Cable Set
Foam Grip
109
110
111
112
113
114
Pivot Axle
Hub Cover
Outer Crank Cover
Flywheel Bracket
M10 Washer
M6 Nut
M8 x 41mm Button Bolt 115
M8 Jamnut
M8 x 23mm Shoulder
Screw
Base Bushing
Crank Arm
M8 x 69mm Button Bolt
M10 Nylon Locknut
M10 x 80mm Carriage
Bolt
#
#
#
3
1
1
Allen Wrench
Grease
Inner Crank Cover
Crank Hub
User’s Manual
Pulley Spacer
Pulley
83
2
M10 x 127mm Button
Screw
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. If a part is miss-
ing, call toll-free 1-888-533-1333. See the back cover of this manual for information about ordering replace-
ment parts.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. 831.28544.2
R0606A
5
10
84
105
88
4
30
10
111
78
79
30
20
74
101
101
17
8
21
101
3
12
18
9
30
17
101
30
30
105
48
79
105
80
90
101
111
78
88
84
79
49
90
73
30
11
15
84
90
84
104
19
22
88
31
115
32
33
73
16
88
115
33
31
115
112
88
112
104
104
1
108
31
33
33
32
35
84
31
34
88
88
115
23
25
81
89
88
84
14
112
108
104
112
82
81
35
26
81
25
89
112
104
13
6
23
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. 831.28544.2
R0606A
103
94
29
52
93
79
54
91
92
94
103
100
107
77
110
94
57
77
53
56
55
72
79
70
110
71
102
103
59
103
60
51
103
102
58
96
50
103
2
85
63
61
95
114
62
103
38
64
97
66
47
44
113
63
100
67
68
66
65
69
62
45
44
47
98
46
106
41
98
40
39
88
107
103
28
109
99
42
38
43
103
76
103
42
87
103
107
103
87
36
86
103
24
75
76
103
86
36
75
103
103
37
87
37
103
27
103
42
99
42
41
7
24
88
43
83
109
27
106
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
®
1-800-4-MY-HOME (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222 Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
1-888-SU-HOGAR® (1-888-784-6427)
TM
SM
® Registered Trademark / Trademark / Service Mark of Sears Brands, LLC
TM
SM
® Marca Registrada / Marca de Fábrica / Marca de Servicio de Sears Brands, LLC
90 DAY FULL WARRANTY
If this Sears Elliptical Exerciser fails due to a defect in material or workmanship within 90 days of the
®
date of purchase, call 1-800-4-MY-HOME (1-800-469-4663) to arrange for free repair (or replacement
if repair proves impossible
This warranty does not apply when the Elliptical Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Part No. 241454 R0606A
Printed in China © 2006 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|