Model No. 831.23744.1
Serial No.
ELLIPTICAL EXERCISER
Write the serial number in the
space above for reference.
User’s Manual
Serial
Number
Decal
• Assembly
• Operation
• Maintenance
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Keep this manual
for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. Sears assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exer-
ciser. Always wear athletic shoes for foot
protection.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
9. Hold the handgrip pulse sensor or the upper
body arms when mounting, dismounting, or
using your elliptical exerciser.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional set-
ting.
10. Keep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
4. Keep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
6. Keep children under age 12 and pets away
from your elliptical exerciser at all times.
14. Use your elliptical exerciser only as
described in this manual.
7. Your elliptical exerciser should not be used
by persons weighing more than 275 lbs.
(124 kg).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for purchasing the revolutionary
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
®
PROFORM XP 520 RAZOR elliptical exerciser. The
XP 520 RAZOR elliptical exerciser provides a wide
array of features designed to make your workouts at
home more effective and enjoyable.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the back
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Fan
Upper Body Arm
Console
Pulse Sensor
Water Bottle Holder*
Ramp Handle
Wheel
Crank Arm
Pedal
Adjustment Knob
*No water bottle is included
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires the included hex keys and your own Phillips screwdriver
wrench , and rubber mallet
, adjustable
.
As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parentheses
below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number
following the parentheses is the quantity needed for assembly. Note: Some small parts may have been pre-
assembled. If a part is not in the parts bag, check to see if it has been preassembled. If a part is missing,
call 1-888-533-1333.
M6 Nylon
M6 Washer
(118)–4
Wave Washer
(88)–6
M10 Split
Locknut (77)–4
Washer (78)–10
M4 x 16mm
M4 x 16mm
Flat Head
M4 x 32mm Screw
M6 x 16mm Button
Screw (80)–6
M6 x 38mm Button
Bolt (76)–4
Screw (84)–14
(95)–2
Screw (94)–4
M10 x 20mm Button
Screw (79)–4
M10 x 35mm Shoulder
Screw (63)–2
M10 x 70mm Button Screw (75)–6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.
1
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical exerciser.
Ramp
Handle
104
Pull the ramp handle outward and lower the
Ramp (104) until it rests on the Frame (1).
Attach a Wheel (50) to the front of the Frame
(1) with an M10 x 35mm Shoulder Screw (63).
Attach the other Wheel (not shown) in the
same way.
1
50
63
2. Identify the Right Frame Cover (49), which is
marked with an “R” sticker. Then, orient the
Right Frame Cover with the rounded side in the
indicated location. While another person lifts the
rear of the Frame (1), attach the Right Frame
Cover with two M4 x 16mm Screws (84).
2
Rounded
Side
48
Repeat this step for the Left Frame
Cover (48).
Rounded
Side
1
49
84
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Tip: Be careful not to pinch the Wire Harness
(100) during this step. Start all screws before
tightening any of them.
3
Wire Tie
Have another person hold the Upright (2) near
the Frame (1). Locate the wire tie in the Upright.
Tie the lower end of the wire tie to the Wire
Harness (100). Next, pull the upper end of the
wire tie upward out of the top of the Upright.
Then, untie and discard the wire tie. Tip: To
prevent the Wire Harness from falling inside
the Upright, secure the Wire Harness with a
rubber band.
Avoid pinching the
Wire Harness (100)
during this step
2
Attach the Upright (2) to the Frame (1) with four
M10 x 20mm Button Screws (79), and four M10
Split Washers (78). Do not tighten the Button
Screws yet.
79
78
78
79
78
100
1
79
4. Tip: Be careful not to pinch the Wire Harness
4
(100) during this step.
3
Avoid pinching the
Wire Harness (100)
during this step
Orient the Bottle Holder (5) as shown and slide
it onto the Upright (2). Attach the Bottle Holder
with two M4 x 32mm Screws (95).
96
100
84
Slide the Console Cover (96) onto the Upright
(2) and move it downward to the Bottle Holder.
Then, insert the Console Bracket (3) into the top
of the Upright. Attach the Console Bracket with
four M4 x 16mm Screws (84).
84
95
2
5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The Console (4) can be operated with four 1.5V
“D” batteries (not included); alkaline batteries are
recommended. IMPORTANT: If the elliptical
exerciser has been exposed to cold tempera-
tures, allow it to warm to room temperature
before inserting batteries into the Console. If
you do not do this, the console displays or
other electronic components may become
damaged. Remove the two screws from the
back of the console, and remove the battery
cover. Insert four batteries into the Console.
Orient the batteries as shown by the markings
inside the battery compartment. Then, reattach
the battery cover.
5
Cover
Batteries
4
Batteries
The Console (4) can also be operated with a
regulated 6-volt DC 2-amp power supply (not
included). To purchase a power supply, call
your local Sears store. To avoid damaging
the console, use only a manufacturer-sup-
plied power supply. Plug one end of the power
supply into the jack on the Console; plug the
other end into an outlet installed in accordance
with all local codes and ordinances.
Screws
6. Tip: Be careful not to pinch the wires during
6
this step.
While a second person holds the Console (4)
near the Upright (2), connect the console wire to
the Wire Harness (100).
4
Attach the Console (4) with four M4 x 16mm
Flat Head Screws (94).
Console Wire
100
Avoid pinching
the wires during
this step
2
96
94
94
8
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Slide the Console Cover (96) (see the drawing
in step 6) upward to the Console (4). Attach the
Console Cover with four M4 x 16mm Screws
(84).
7
4
96
84
84
8. Apply a generous amount of the included
grease to the Pivot Axle (16). Then, apply a
small amount of grease to two Wave Washers
(88).
8
Insert the Pivot Axle (16) into the Upright (2).
Slide a Wave Washer (88) onto each end of the
Pivot Axle.
2
88
80
20
Identify the Left Upper Body Leg (6), which is
marked with an “L” sticker. Slide the Left Upper
Body Leg onto the Pivot Axle (16). Attach the
Left Upper Body Leg with an M6 x 16mm Button
Screw (80) and a Large Axle Cover (20). Attach
the Right Upper Body Leg (124) in the same
way.
16
6
20
80
88
Grease
124
9
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Attach the Left Pedal (12) to the left Pedal Arm
(14) with three M10 x 70mm Button Screws
(75), three M10 Split Washers (78), and an M4
x 16mm Screw (84).
9
14
Repeat this step for the other side of the
elliptical exerciser.
78
12
75
78
84
10. Apply a small amount of grease to two Wave
Washers (88) and to the axles on a Pedal Arm
Axle (21).
10
Curved Side
Identify an Upper Body Leg Spacer (113), which
has a curved side. Slide a Wave Washer (88)
and the Upper Body Leg Spacer onto the indi-
cated axle of the Pedal Arm Axle (21); make
sure that the curved side of the Upper Body
Leg Spacer is facing away from the Pedal
Arm Axle.
Grease
113
88
Flat Side
88
Identify a Pedal Leg Spacer (114), which has a
flat side. Slide a Wave Washer (88) and the
Pedal Leg Spacer onto the other axle of the
Pedal Arm Axle (21); make sure that the flat
side of the Pedal Leg Spacer is facing away
from the Pedal Arm Axle.
21
114
Grease
Repeat this step for the other Pedal Arm
Axle (not shown).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11. At the same time, insert a Pedal Arm Axle (21)
into the Right Upper Body Leg (124) and into
the right Pedal Arm (14); make sure that the
Upper Body Leg Spacer (113) and the Pedal
Leg Spacer (114) are in the indicated loca-
tions.
11
Attach the Right Upper Body Leg (124) with an
M6 x 16mm Button Screw (80) and an M6
Washer (118).
124
118
80
Then, attach the right Pedal Arm (14) with an
M6 x 16mm Button Screw (80) and an M6
Washer (118).
113
80
118
14
Repeat this step for the other side of the
elliptical exerciser.
See step 3. Tighten the four M10 x 20mm
Button Screws (79). Tip: Tighten the two
Button Screws on the front of the elliptical
exerciser before tightening the other two
Button Screws.
21
114
12. Identify the Right Upper Body Arm (9), which is
marked with an “R” sticker. Orient the Right
Upper Body Arm as shown; make sure that
the hexagonal holes in the Right Upper
Body Arm are in the indicated location.
12
Slide the Right Upper Body Arm (9) onto the
Right Upper Body Leg (124). Attach the Right
Upper Body Arm with two M6 x 38mm Button
Bolts (76) and two M6 Nylon Locknuts (77);
make sure that the Nylon Locknuts are
inside the hexagonal holes.
8
9
77
Repeat this step for the Left Upper Body
Arm (8) and the Left Upper Body Leg (6).
76
Hexagonal
Holes
6
124
13. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO MOVE THE ELLIPTICAL EXERCISER
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
Due to the size and weight of the elliptical exercis-
er, moving it requires two persons. Stand in front of
the elliptical exerciser, hold the upright, and place one
foot against one of the front wheels. IMPORTANT: Do
not place your foot on the ramp cover. Pull on the
upright and have a second person lift the base until
the elliptical exerciser will roll on the front wheels.
Carefully move the elliptical exerciser to the desired
location, and then lower it to the floor.
To mount the elliptical exerciser, hold the upper body
arms and step onto the pedal that is in the lowest
position. Next, step onto the other pedal. Push the
pedals until they begin to move with a continuous
motion. Note: The crank arms can turn in either
direction. It is recommended that you turn the
crank arms in the direction shown by the arrow
below; however, for variety you can turn the crank
arms in the opposite direction.
Upper Body Arms
Upright
Pedals
Crank Arm
Place
your foot
here
Wheel
Lift here
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. Note: The elliptical
exerciser does not have a free wheel; the pedals
will continue to move until the flywheel stops.
When the pedals are stationary, step off the higher
pedal first. Then, step off the lower pedal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE STRIDE OF THE
ELLIPTICAL EXERCISER
HOW TO CHANGE THE INCLINE OF THE RAMP
To vary the motion of the pedals, you can change the
incline of the ramp. To change the incline, pull the
ramp handle outward, raise or lower the ramp, and
engage the ramp pin into one of the adjustment holes
in the front of the frame.
To adjust the stride of the elliptical exerciser, first pull
one of the adjustment knobs until the adjustment
bracket pivots freely. Pivot the adjustment bracket until
the adjustment knob is aligned with one of the holes in
the crank arm, and gently release the knob. Then,
pivot the adjustment bracket back and forth slightly to
make sure that the adjustment pin is engaged in one
of the holes in the crank arm.
Ramp
Pin
Ramp
Handle
Adjustment
Pin
Adjustment
Bracket
Ramp
Adjustment
Knob
Holes
Crank
Arm
Adjust the other side of the elliptical exerciser in the
same way.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The console also offers two target toning workouts
designed to work specific areas of the body. The con-
sole guides you through each workout with a variety of
exercise instructions while automatically changing the
resistance of the pedals.
The advanced console offers an array of features
designed to make your workouts more effective and
enjoyable.
When you use the manual mode of the console, you
can change the resistance of the pedals with the touch
of a button. As you exercise, the console will display
continuous exercise feedback. You can even measure
your heart rate using the handgrip pulse sensor.
In addition, you can use three calorie goal workouts
designed to help you burn 300 or 400 calories in 30- or
45-minute workouts. The calorie goal workouts auto-
matically control the resistance of the pedals and
prompt you to vary your pace while counting the calo-
ries you burn.
The console offers three interactive cross training
workouts designed to help you to burn calories and
enhance your cardiovascular system while toning and
strengthening your muscles. The cross training work-
outs automatically control the resistance of the pedals
and prompt you to perform a variety of strength exer-
cises during your workout. Note: The strength exercis-
The console also has a high performance workout that
automatically changes the resistance of the pedals and
prompts you to vary your pace as it guides you through
an effective workout.
To use the manual mode of the console, follow the
es require the use of dumbbells and an inflatable exer- steps beginning on page 15. To use a cross training
cise ball (not included). To purchase dumbbells or
workout, see page 16. To use a target toning work-
out, see page 18. To use a calorie goal workout,
see page 19. To use the high performance workout,
see page 20.
an exercise ball, call 1-888-533-1333.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE MANUAL MODE
The left display will also show your heart rate when
you use the handgrip pulse sensor (see step 5 on
page 16).
Note: If there is a sheet of clear plastic on the face of
the console, remove the plastic.
When you select a workout, the left display will also
show the approximate number of calories you have
burned.
1. Press the Resistance decrease button or begin
pedaling to turn on the console.
A moment after you turn on the console, the dis-
plays will light.
The center display—
When you select the
manual mode, the cen-
2. Select the manual mode.
ter display will show a
track that represents
Each time you turn on the console, the manual
mode will be selected automatically. If you have
selected a workout, reselect the manual mode by
pressing the Workout button repeatedly until the
words MANUAL MODE appear in the upper
display.
640 revolutions. As you
exercise, indicators will appear in succession
around the track until the entire track appears. The
track will then disappear and the indicators will
again begin to appear in succession.
The center display will
also show the resis-
tance level of the ped-
als for a few seconds
each time the resis-
tance level changes.
The right display—
This display will show
the distance (total revo-
lutions) you have ped-
aled and your pedaling
pace, in revolutions per
minute (rpm).
3. Begin pedaling and change the resistance of
the pedals as desired.
As you pedal, change the resistance of the pedals
by pressing the Resistance increase and decrease
buttons repeatedly. There are ten resistance lev-
els. Note: After you press the buttons, it will take a
moment for the pedals to reach the selected resis-
tance level.
The upper display—When you select the manual
mode, the upper display will show the approximate
number of calories you have burned and the
approximate number of grams of carbs you have
burned.
4. Follow your progress with the displays.
The left display—This
display will show the
elapsed time. Note:
When you select a
workout, the display will
show the time remain-
ing in the workout instead of the elapsed time.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Measure your heart rate if desired.
If there are sheets of
HOW TO USE A CROSS TRAINING WORKOUT
1. Turn on the console.
clear plastic on the
metal contacts on the
handgrip pulse sen-
sor, remove the plas-
tic. To measure your
heart rate, hold the
Metal Contacts
See step 1 on page 15.
2. Select a cross training workout.
To select a cross training workout, press the
Workout button repeatedly until the words UPPER
BODY, LOWER BODY, or WHOLE BODY appear
in the upper display.
handgrip pulse sensor
with your palms resting
against the metal con-
tacts. Avoid moving your hands or gripping the
contacts tightly.
When your pulse is
detected, a heart-
shaped symbol will
Profile
flash in the left display.
Each time your heart
beats, one or two
When you select a cross training workout, the
name of the workout and the workout time will
appear in the displays and a profile of the resis-
tance levels of the workout will scroll across the
center display.
dashes will appear, and then your heart rate will
be shown. For the most accurate heart rate read-
ing, hold the contacts for at least 15 seconds. Note:
If you continue to hold the handgrip pulse sensor,
the display will show your heart rate for up to 30
seconds.
3. Begin pedaling to start the workout.
If your heart rate is not shown, make sure that your
hands are positioned as described. Be careful not
to move your hands excessively or to squeeze the
metal contacts tightly. For optimal performance,
clean the metal contacts using a soft cloth; never
use alcohol, abrasives, or chemicals to clean
the contacts.
Each workout is divided into 25 or 45 one-minute
segments. One resistance level and one target
rpm (revolutions per minute) setting are pro-
grammed for most segments. (Note: The same
resistance level and/or target rpm setting may be
programmed for consecutive segments.) During
other segments, the console will prompt you to per-
form strength exercises.
6. Turn on the fan if desired.
During the workout, the workout profile will show
your progress (see the drawing above). The flash-
ing segment of the profile represents the current
segment of the workout. The height of the flashing
segment indicates the resistance level for the cur-
rent segment. At the end of each segment of the
workout, a series of tones will sound and the next
segment of the profile will begin to flash. If a differ-
ent resistance level is programmed for the next
segment, the resistance level will appear in the
display for a few seconds to alert you. The resis-
tance of the pedals will then change.
The fan has high and low speed settings. Press
the Fan button repeatedly to select a fan speed or
to turn off the fan. Note: If the pedals do not move
for about thirty seconds, the fan will turn off auto-
matically.
7. When you are finished exercising, the console
will turn off automatically.
If the pedals do not move for several seconds, a
series of tones will sound, the console will pause,
and the time will flash in the display.
If the pedals do not move for about five minutes,
the console will turn off and the display will be
reset.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the upper display or the GO
FASTER indicator on the pace guide is lit,
Step off the elliptical exerciser and prepare to
begin the first strength exercise. Every few sec-
onds, the console will sound a tone; when a tone
sounds, perform one repetition of the exercise.
Exercise with a slow, steady motion; do not per-
form more than one repetition each time a tone
sounds. The display will count down the repetitions
as you perform them.
increase your pace. When the words PEDAL
SLOWER appear or the GO SLOWER indicator is
lit, decrease your pace. When the words PEDAL-
ING IN RANGE appear or when the center indica-
tor is lit, maintain your current pace.
Note: Refer to a weight training manual or exer-
cise guide if you are unfamiliar with the correct
form for each strength exercise. When performing
lunges, alternate legs with each repetition. When
performing dumbbell rows, perform half the repeti-
tions with your right arm and half the repetitions
with your left arm. The strength exercises require
the use of dumbbells and an inflatable exercise
ball (not included). To purchase dumbbells or an
exercise ball, call 1-888-533-1333.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actu-
al pace may be slower than the target rpm set-
tings. Make sure to pedal at a pace that is com-
fortable for you.
5. Continue the cross training workout.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance decrease and
increase buttons. However, when the current seg-
ment ends, the pedals will automatically adjust to
the resistance level for the next segment.
When you have performed the recommended
number of repetitions, the words START PEDAL-
ING will appear in the upper display. To continue
the cross training workout, step onto the elliptical
exerciser and start pedaling. The pedals will auto-
matically adjust to the resistance level for the next
segment.
If you stop pedaling for several seconds, a series
of tones will sound and the workout will pause. To
restart the workout, simply resume pedaling. The
workout will continue until the last segment of the
profile flashes and the last segment of the workout
ends.
The workout will continue in this way until the last
segment ends. Then, the words PROGRAM
DONE will appear in the upper display.
4. Perform the first strength exercise when
prompted.
When the first strength exercise segment begins,
the name of the first strength exercise will appear
in the upper display for a few seconds. The time
will pause and flash in the left display.
6. Follow your progress with the displays.
See step 4 on page 15.
7. Measure your heart rate if desired.
See step 5 on page 16.
8.
Turn on the fan if desired.
See step 6 on page 16.
9. When you are finished exercising, the console
will turn off automatically.
Next, the upper display will show the recommend-
ed number of repetitions for the first strength exer-
cise.
See step 7 on page 16.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A TARGET TONING WORKOUT
1. Turn on the console.
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the upper display or the GO
FASTER indicator on the pace guide is lit,
See step 1 on page 15.
increase your pace. When the words PEDAL
SLOWER appear or the GO SLOWER indicator is
lit, decrease your pace. When the words PEDAL-
ING IN RANGE appear or when the center indica-
tor is lit, maintain your current pace.
2. Select a target toning workout.
To select a target toning workout, press the
Workout button repeatedly until the words TAR-
GET TONING 1 or TARGET TONING 2 appear in
the upper display.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actu-
al pace may be slower than the target rpm set-
tings. Make sure to pedal at a pace that is com-
fortable for you.
Profile
When you select a target toning workout, the
name of the workout and the workout time will
appear in the displays and a profile of the resis-
tance levels of the workout will scroll across the
center display.
If the resistance level for the current segment is
too high or too low, you can manually override the
setting by pressing the Resistance decrease and
increase buttons. However, when the current seg-
ment ends, the pedals will automatically adjust to
the resistance level for the next segment.
3. Begin pedaling to start the workout.
Each workout is divided into 30 one-minute seg-
ments. One resistance level and one target rpm
(revolutions per minute) setting are programmed
for each segment. Note: The same resistance level
and/or target rpm setting may be programmed for
consecutive segments.
If you stop pedaling for several seconds, a series
of tones will sound and the workout will pause. To
restart the workout, simply resume pedaling. The
workout will continue until the last segment of the
profile flashes and the last segment of the workout
ends.
During the workout, the workout profile will show
your progress (see the drawing above). The flash-
ing segment of the profile represents the current
segment of the workout. The height of the flashing
segment indicates the resistance level for the cur-
rent segment. At the end of each segment of the
workout, a series of tones will sound and the next
segment of the profile will begin to flash. If a differ-
ent resistance level is programmed for the next
segment, the resistance level will appear in the
display for a few seconds to alert you. The resis-
tance of the pedals will then change.
When the last segment of the workout ends, the
words PROGRAM DONE will appear in the upper
display.
4. Follow your progress with the displays.
See step 4 on page 15.
5. Measure your heart rate if desired.
See step 5 on page 16.
6. Turn on the fan if desired.
See step 6 on page 16.
As you exercise, the console will display a variety
of exercise instructions that will help you get the
most benefit from your workout. For example, the
console may instruct you to PEDAL BACKWARD,
USE UPPER BODY, or FOCUS LOWER BODY
during certain segments of the workout.
7. When you are finished exercising, the console
will turn off automatically.
See step 7 on page 16.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A CALORIE GOAL WORKOUT
1. Turn on the console.
See step 1 on page 15.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actu-
al pace may be slower than the target rpm set-
tings. Make sure to pedal at a pace that is com-
fortable for you. Note: If you manually override
the resistance settings of a calorie goal workout,
you may not reach your calorie goal.
2. Select a calorie goal workout.
Press the Workout button repeatedly until the name
of the desired calorie goal workout appears in the
upper display. When you select a calorie goal
workout, the name of the workout and the workout
time will appear in the displays and a profile of the
resistance levels of the workout will scroll across
the center display.
If you stop pedaling for several seconds, a series
of tones will sound and the workout will pause. To
restart the workout, simply resume pedaling. The
workout will continue until the last segment of the
profile flashes and the last segment of the workout
ends.
When the last segment of the workout ends, the
words PROGRAM DONE will appear in the upper
display.
Profile
3. Begin pedaling to start the workout.
4. Follow your progress with the displays.
See step 4 on page 15.
Each workout is divided into 30 or 45 one-minute
segments. One resistance level and one target
rpm (revolutions per minute) setting are pro-
grammed for each segment. Note: The same resis-
tance level and/or target rpm setting may be pro-
grammed for consecutive segments. The displays
for a calorie goal workout will work in the same way
as the displays for a cross training workout (see
step 3 on page 16).
5. Measure your heart rate if desired.
See step 5 on page 16.
6. Turn on the fan if desired.
See step 6 on page 16.
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the upper display or the GO
FASTER indicator on the pace guide is lit,
7. When you are finished exercising, the console
will turn off automatically.
See step 7 on page 16.
increase your pace. When the words PEDAL
SLOWER appear or the GO SLOWER indicator is
lit, decrease your pace. When the words PEDAL-
ING IN RANGE appear or when the center indica-
tor is lit, maintain your current pace.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE HIGH PERFORMANCE WORKOUT
1. Turn on the console.
ING IN RANGE appear or when the center indica-
tor is lit, maintain your current pace.
See step 1 on page 15.
2. Select the high performance workout.
IMPORTANT: The target rpm settings are
intended only to provide motivation. Your actu-
al pace may be slower than the target rpm set-
tings. Make sure to pedal at a pace that is com-
fortable for you.
Press the Workout button repeatedly until the words
HIGH PERFORMANCE appear in the upper dis-
play. The workout time will appear in the left dis-
play and a profile of the resistance levels for the
workout will scroll across the center display.
If you stop pedaling for several seconds, a series
of tones will sound and the workout will pause. To
restart the workout, simply resume pedaling. The
workout will continue until the last segment of the
profile flashes and the last segment of the workout
ends.
Profile
When the last segment of the workout ends, the
words PROGRAM DONE will appear in the upper
display.
3. Begin pedaling to start the workout.
The workout is divided into 45 one-minute seg-
ments. One resistance level and one target rpm
setting are programmed for each segment. Note:
The same resistance level and/or target rpm (revo-
lutions per minute) setting may be programmed for
consecutive segments. The displays for the high
performance workout will work in the same way as
the displays for a cross training workout (see step 3
on page 16).
4. Follow your progress with the displays.
See step 4 on page 15.
5. Measure your heart rate if desired.
See step 5 on page 16.
6. Turn on the fan if desired.
See step 6 on page 16.
As you exercise, you will be prompted to keep
your pedaling pace near the target rpm setting for
the current segment. When the words PEDAL
FASTER appear in the upper display or the GO
FASTER indicator on the pace guide is lit,
7. When you are finished exercising, the console
will turn off automatically.
increase your pace. When the words PEDAL
SLOWER appear or the GO SLOWER indicator is
lit, decrease your pace. When the words PEDAL-
See step 7 on page 16.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLESHOOTING
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
until the console displays correct feedback. When the
Reed Switch is correctly adjusted, reattach the side
shields. Note: If you have questions as to which screw
should be in which hole, see EXPLODED DRAWING
B on page 27 and the PART LIST on page 24.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
HOW TO ADJUST THE BELT
If you can feel the pedals slip while you are pedaling,
even when the resistance of the pedals is at the high-
est setting, the Belt (46) may need to be adjusted.
First, remove all the screws from both side shields;
there are three sizes of screws in the side
shields—note which size of screw you remove
from each hole. Then, gently pry the side shields
away from the frame.
BATTERY REPLACEMENT
If the console displays become dim, the batteries
should be replaced; most console problems are the
result of low batteries. See assembly step 5 on page 8
for replacement instructions.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
Next, turn the
If the handgrip pulse sensor does not function proper-
ly, see step 5 on page 16.
Belt Adjustment
Screw (72) until
the Belt (46) is
tight. Then, reat-
tach the side
46
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
shields. Note: If
reed switch should be adjusted. First, remove all of the you have ques-
screws from both side shields; there are three sizes
of screws in the side shields—note which size of
screw you remove from each hole. Then, gently pry
the side shields away from the frame.
tions as to which
screw should be
in which hole,
72
see EXPLODED
DRAWING B on page 27 and the PART LIST on page
24.
Next, locate the
Reed Switch (58).
Turn the Left
41
58
26
Pedal Disc (26)
until the Magnet
(41) is aligned
with the Reed
Switch. Loosen,
but do not
84
remove, the indi-
cated M4 x
16mm Screw
(84). Slide the
Reed Switch slightly closer to or away from the
Magnet, and then retighten the Screw. Rock the Left
Pedal Disc forward and backward just enough that the
Magnet passes the Reed Switch repeatedly. Repeat
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for
persons over the age of 35 or persons with
pre-existing health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until
your heart rate is near the highest number in your
training zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of
stretching. Stretching increases the flexibility of your
muscles and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right.
Move slowly as you stretch—never bounce.
1
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts,
then relax. Repeat 3 times. Stretches: Hamstrings, back of
knees, and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back, and groin.
3. Calf/Achilles Stretch
3
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat
3 times for each leg. To cause further stretching of the achilles
tendons, bend your back leg as well. Stretches: Calves, achilles
tendons, and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your
buttocks as possible. Hold for 15 counts, then relax. Repeat 3
times for each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
5
Sit with the soles of your feet together and your knees outward.
Pull your feet toward your groin area as far as possible. Hold for
15 counts, then relax. Repeat 3 times. Stretches: Quadriceps and
hip muscles.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.23744.1
R1107A
Key No. Qty.
Description
Key No. Qty.
Description
1
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
1
2
2
10
2
2
4
2
1
1
1
1
2
2
2
1
4
2
4
2
2
2
2
1
1
2
1
1
1
1
Frame
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
4
4
4
1
2
2
6
4
4
10
4
6
4
3
7
35
2
2
2
6
6
4
Belt
2
Upright
Foot
3
Console Bracket
Console
Left Frame Cover
Right Frame Cover
Wheel
4
5
Bottle Holder
6
Left Upper Body Leg
Idler Wheel
Flywheel
7
Idler
8
Left Upper Body Arm
Right Upper Body Arm
Foam Grip
“C” Magnet
Resistance Motor
Motor Bracket
Resistance Arm
Clamp
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
Upper Endcap
Left Pedal
Right Pedal
Reed Switch/Wire
Magnet Spacer
Key
Pedal Arm
Pedal Bracket
Pivot Axle
Square Nut
Flange Screw
Inner Bushing Set
Outer Bushing Set
Upright Bushing
Large Axle Cover
Pedal Arm Axle
Axle Cover
M10 x 35mm Shoulder Screw
Flywheel Bolt
“C” Magnet Bolt
Idler Bolt
Key Screw
Wheel Cover
Crank Arm Screw
Crank Assembly
Crank Arm
Resistance Motor Bolt
Resistance Motor Nut
Motor Bracket Screw
Belt Adjustment Screw
M10 x 58mm Shoulder Bolt
M10 Nylon Locknut
M10 x 70mm Button Screw
M6 x 38mm Button Bolt
M6 Nylon Locknut
M10 Split Washer
Left Pedal Disc
Right Pedal Disc
Pedal Disc Cover
Adjustment Pin
Spring
Left Adjustment Bracket
Large Snap Ring
39mm x 31mm Wave Washer
Adjustment Bushing
Pedal Arm Bracket
Adjustment Knob
Fender Washer
Crank Bearing
Crank Spacer
M10 x 20mm Button Screw
M6 x 16mm Button Screw
M8 x 12mm Button Screw
M8 Nylon Locknut
M6 Star Washer
M4 x 16mm Screw
Flywheel Spacer
Crank Arm Spacer
Magnet
M8 Washer
Left Front Side Shield
Right Front Side Shield
Left Side Shield
Right Side Shield
31mm x 24mm Wave Washer
Wave Washer
M4 Washer
M6 Large Washer
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
91
92
3
10
2
4
2
1
2
7
1
1
1
1
1
1
1
1
1
1
1
M4 x 48mm Screw
M4 x 25mm Screw
M4 x 35mm Screw
M4 x 16mm Flat Head Screw
M4 x 32mm Screw
Console Cover
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
*
1
6
1
2
2
2
4
2
4
6
2
2
10
2
1
1
–
–
–
Ramp Lock Bushing
Ramp Bushing
93
Ramp Axle
94
Upper Body Leg Spacer
Pedal Leg Spacer
Wheel
95
96
97
M8 x 18mm Button Screw
M5 x 12mm Screw
M3 x 12mm Screw
Wire Harness
Wheel Bushing
98
M8 x 51mm Bolt Set
M6 Washer
99
100
101
102
103
104
105
106
107
108
109
M4 Large Washer
M5 x 30mm Screw
M10 x 16mm Button Screw
M4 x 16mm Round Head Screw
M10 Washer
Extended Reed Switch Wire
Right Adjustment Bracket
Ramp Cover
Ramp
Top Ramp Handle
Bottom Ramp Handle
Ramp Lock Shaft
Ramp Lock Spring
Ramp Lock Pin
Right Upper Body Leg
Tree Fastener
User’s Manual
*
Hex Key
*
Grease Packet
Note: Specifications are subject to change without notice. See the back cover of this manual for information
about ordering replacement parts. *These parts are not illustrated. If a part is missing, call 1-888-533-1333.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. 831.23744.1
R1107A
3
11
10
11
94
4
96
8
10
84
9
5
100
95
76
18
77
84
80
20
76
84
77
18
17
17
13
12
2
80
19
16
20
6
88
19
88
124
22
19
118
88
113
19
21
118
80
19
80
84
19
84
88
113
23
114
14
88
116
73
15
23
118
117
19
79
78
115
116
116
115
80
78
79
79
117
19
75
22
116
118
78
78
114 117
88
14
78
117
19
86
82
21
22
89
80
78
75
19
78
84
15
105
73
89
103
84
107
110
106
89
86
82
84
104
122
84
119
120
84
84
119
84
111
108
121
109
111
123
111
119
84
123
112
121
111
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. 831.23744.1
R1107A
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair—in your home—of all major brand appliances, lawn and garden equipment,
or heating and cooling systems, no matter who made it, no matter who sold it!
For the replacement parts, accessories, and user’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
®
1-800-4-MY-HOME (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222 Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación a domicilio, y para ordenar piezas:
®
1-888-SU-HOGAR (1-888-784-6427)
TM
SM
® Registered Trademark / Trademark / Service Mark of Sears Brands, LLC
TM
SM
® Marca Registrada / Marca de Fábrica / Marca de Servicio de Sears Brands, LLC
90 DAY FULL WARRANTY
If this Sears Elliptical Exerciser fails due to a defect in material or workmanship within 90 days of the
®
date of purchase, call 1-800-4-MY-HOME (1-800-469-4663) to arrange for free repair (or replacement
if repair proves impossible). There is a seven year warranty on the frame.
This warranty does not apply when the Elliptical Exerciser is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Part No. 261605 R1107A
Printed in China © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|