ESPAÑOL: PÁGINA 15
FRANÇAISE : PAGE 29
Instruction
manual
Power Tool-Triggered
Wet/Dry Vac
MODEL 7812/7814
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2004 Porter-Cable Corporation
Part No. 904362 - 10-12-04
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The
information it contains relates to protecting YOUR SAFETY and
PREVENTING PROBLEMS. The symbols below are used to help
you recognize this information.
indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,could result in death or serious injury.
indicates a potentially hazardous situation which, if not
avoided,may result in minor or moderate injury.
used without the safety alert symbol indicates potentially
hazardous situation which, if not avoided, may result in
property damage.
● Wear eye and hearing protection. Always use safety glasses. Everyday
eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY EQUIPMENT.
Eye protection equipment should comply with ANSI Z87.1 standards.
Hearing equipment should comply with ANSI S3.19 standards.
● Take precautions against dust inhalation. The dust generated by certain
woods and wood products can be injurious to your health. Always operate
machinery in well-ventilated areas, and provide for proper dust removal.
Use wood dust collection systems whenever possible. Also, use face or
dust mask if cutting operation is dusty. Dust mask protection should comply
with MSHA/NIOSH certified respirator standards. Splinters, air-borne debris,
and dust can cause irritation, injury, and/or illness.
● Do not pick up anything that is burning, smoldering, or smoking such as
matches, cigarettes, or hot ashes.
● Do not use to vacuum combustible explosive materials, such as coal,
grain, or other finely divided combustible material.
● Do not use to vacuum hazardous, toxic, or carcinogenic materials, such
as asbestos, pesticide or lead-based paint debris.
● Never pick-up explosive liquids (e.g. gasoline, diesel fuel, heating oil, paint
thinner, etc.), acids or solvents.
SAVE THESE INSTRUCTIONS!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
Read all instructions Failure to follow all
instructions listed below may result in electric shock, fire and/or
serious injury.
NOTE: This vacuum is intended for commercial use.
SAFETY INSTRUCTIONS
GROUNDING INSTRUCTIONS
This Appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to reduce the
risk of electric shock. This appliance is equipped with a cord having an
equipment-grounding conductor and grounding plug. The plug must be inserted
into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check with a qualified electrician
or service person if you are in doubt as to whether the outlet is properly
grounded. Do not modify the plug provided with the appliance - if it will not fit
the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a nominal
GROUNDED OUTLET BOX
120-volt circuit, and has a grounded
CURRENT
plug that looks like the plug illustrated in
CARRYING
Figure A. A temporary adapter that looks
like the adapter illustrated in Fig. B may
be used to connect this plug to a 1-pole
receptacle as shown in Fig. B if a
properly grounded outlet is not available.
The temporary adapter should be used
only until a properly grounded outlet
(Fig. A) can be installed by a qualified
electrician. The green colored rigid ear,
lug, or the like extending from the
adapter must be connected to a
permanent ground such as a properly
grounded outlet box cover. Whenever
the adapter is used, it must be held in
place by a metal screw.
PRONGS
GROUNDING PRONG
IS LONGEST OF THE 3 PRONGS
Fig. A
GROUNDED OUTLET BOX
GROUNDING MEANS
ADAPTER
Note: In Canada, the use of a
temporary adapter is not permitted
by the Canadian Electrical Code.
Fig. B
SAVE THESE INSTRUCTIONS!
4
Download from Www.Somanuals.com. All Manuals Search And Download.
continued
GENERAL SAFETY RULES
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
When using electric appliances, always follow basic
safety precautions to reduce the risk of fire, electric shock and personal injury,
including the following:
BEFORE USING THIS APPLIANCE,
READ AND FOLLOW ALL INSTRUCTIONS.
1. Connect to a properly grounded outlet only (See Grounding
Instructions).
2. Do not leave the appliance when it is connected to a power source.
Unplug it from outlet when not in use and before servicing.
3. Do not expose the appliance to rain. Store it indoors. This action will
reduce the risk of electric shock.
4. Do not allow the appliance to be used as a toy. Pay close attention
when the appliance is used by children, or when children are nearby.
5. Use this appliance ONLY as described in the manual. Use only
recommended attachments from Porter-Cable.
6. Do not use this appliance with a damaged cord or plug. If the appliance
is not working correctly, or if it has been dropped, damaged, left
outdoors, or dropped in water, return it to a service center.
7. Do not pull or carry this appliance by the cord. Do not use the cord as a
handle, close a door on the cord, or pull the cord around sharp edges or
corners. Do not run the appliance over the cord. Keep the cord away
from heated surfaces.
8. Do not unplug this appliance by pulling on the cord. To unplug, grasp
the plug, not the cord.
9. Do not handle the plug or appliance with wet hands.
10. Do not put any objects into the openings of the appliance. Do not use
the appliance with any opening blocked. Keep all openings free of dust,
lint, hair, or anything else that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all body parts away from the
openings and moving parts.
12. Turn off all controls before unplugging appliance.
13. Use extra care when using the appliance on stairs.
14. Do not use the appliance to pick up flammable or combustible liquids,
such as gasoline, or use the appliance in areas where flammable or
combustible liquids are present.
15. Do not pick up anything that is burning or smoking (cigarettes, matches,
or hot ashes).
16. Do not pick up anything that contains lead-based paint debris.
17. Do not use this appliance without a dust bag and/or filters in place.
18. Some wood contains preservatives which can be toxic. Take extra care to
prevent inhalation and skin contact when working with these materials.
Request and follow any safety information available from your material
supplier.
SAVE THESE INSTRUCTIONS!
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown on
the specification plate on the tool. Several models, however, are designed for
A.C. current only. Refer to the specification plate on your tool for proper voltage
and current rating.
Do not operate your tool on a current on which the voltage is not
within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found in
this section. This table is based on limiting line voltage drop to 5 volts (10 volts
for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix W-A
or W following the cord type designation. For example – SJTW-A to indicate it is
acceptable for outdoor use.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft.
250 Ft. 300 Ft.
500 Ft. 600 Ft.
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
CARTON CONTENTS
1) Vacuum
2) Hose & Connectors
3) Wheels & Wheel Parts
4) Bag Filter
5) Instruction Manual
6) Replacement Parts List
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL DESCRIPTION
FOREWORD
Porter-Cable Model 7812/7814 Wet/Dry Vacuum delivers 99.85% filtration
efficiency which is great for fine particulate pick-up, like drywall or surface
dust. These units come equipped with a powerful 9 amp motor, built in
outlet for use with power tools providing automatic vacuum start-up when
tool is turned on and a 6 - 10 second vacuum overrun to clear hose when
tool is turned off, dual filtration system, corrosion resistant tank, large wheels
for easy maneuvering and a convenient flat top surface tray for holding tools
while working.
UNPACKING
Carefully remove the Vacuum Cleaner from the carton. Retain all packing
materials until you have inspected and satisfactorily operated the Vacuum
Cleaner.
Do not connect the appliance to the power source until
you read and understand this entire instruction manual.
Release the two container locks (A) Fig. 1, (one on each side of Vacuum
Cleaner), by pulling outward on the bottom of each lock.
Lift the Motor Unit from the container and carefully set aside.
Remove the wheels and accessories from the container.
A
B
A
Fig. 1
Fig. 2
ASSEMBLY
ASSEMBLY TOOLS REQUIRED - Adjustable Wrench, Rubber Mallet.
ASSEMBLY TIME ESTIMATE - 30 minutes or less.
DISCONNECT APPLIANCE FROM POWER SOURCE.
NOTE: For Model 7814, begin with instruction #5.
1. Invert the container on a solid, flat surface (like a workbench or floor).
2. Install the two Steering Rollers (A) Fig. 2 into the holes provided in the
bottom of the container. Seat firmly.
3. Insert the wand rest, (B) Fig. 2 into its position and seat firmly.
4. The wheel and axle assembly consists of two wheels on an axle. Place
this assembly in the slot provided in the bottom of the container, and
press into place. Seat firmly. (See Figure 2)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Set container upright, on its wheels.
NOTE: If the Vacuum Cleaner is to be used to pick-up liquid or wet
material, skip step 6.
6. Install the paper filter bag. Please note that the mounting hole is offset in
the bag. The hole is closest to the top side of the bag. Position the bag
(into the container), with its top side up, and seat mounting hole onto
the container’s intake port. NOTE: Press only on the bag’s protective
card. Be careful to not tear the bag.
7. Place the motor unit onto the container and secure it by closing the two
container Locks.
8. Attach the vacuum hose to the
machine (Fig. 3). The Hose is
equipped with a bayonet style
connector. Align the projection
on the side of the Hose
connector with the slot in the
Container intake port. Slide
connector into intake port and
rotate one-quarter turn
clockwise to lock.
Fig. 3
NOTE: Models 7812 and 7814 Vacuum Cleaners are equipped with
a Static Dissipating System that can help dissipate static electrical
charges (sometimes experienced when recovering very dry,
powdered materials), when used with a Static Dissipating type
vacuum hose. The hose that comes with your unit is NOT a
static dissipating hose. To install a Static Dissipating type hose
will require removal of the bayonet connector from the standard
hose, and installation (of the bayonet connector), onto the Static
Dissipating hose, as follows:
A. Depress locking tab (A) Fig. 4A and pull collar (B) out of the
bayonet connector slightly.
B. Rotate the assembly 180° and depress the second locking tab,
allowing the bayonet connector to be separated from the hose
assembly.
C. Grasp hose in one hand and mounting hub (C) Fig. 4B in the
other. Rotate the mounting hub clockwise (left-hand thread) to
remove it from the hose.
D. Slide the collar (B) off the standard hose and position it onto the
Static Dissipating hose.
E. Thread the mounting hub (C) onto the Static Dissipating hose
(by turning it counterclockwise).
F. Place the bayonet connector onto the mounting hub and
position the collar (B), so that its locking tabs align with the
holes in the bayonet connector.
G. Press the collar into the bayonet connector until the two locking
tabs engage the holes in the bayonet connector.
9. Attach the Vacuum Hose to the appropriate accessory nozzle, or to the
dust port of a power tool.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
Fig. 4A
C
B
Fig. 4B
OPERATION
The Porter-Cable Power Tool-Triggered Wet/Dry Vac is designed for use as
a general purpose shop vacuum, or for use connected to various power
tools. With the dust bag removed, it can be used to pick up water and other
wet materials.
A power outlet is provided that allows a power tool to be connected to the
Vacuum Cleaner. The Vacuum Cleaner will automatically switch “ON” when
the power tool is started, and it will automatically switch “OFF”
approximately 6 to 10 seconds after the power tool is turned “OFF”.
POWER SWITCH
The power switch (A) Fig. 5 on both the 7812 and 7814 models is used for
the Vacuum Cleaner as a stand alone unit. When not using a power tool,
depress power switch (A) Fig. 5 to begin vacuuming.
These vacuums can be used to provide a dust-free environment when
attached to a power tool. An accessory outlet is located under a hinged
cover (B) Fig. 5 on the front of the vacuum cleaner. Lift this cover to expose
the outlet.
Connect the power cord of the
power tool to outlet (B) Fig. 5, then
A
depress power switch (A) Fig. 5 on
the vacuum cleaner. A green light,
located next to the outlet, will glow.
This light indicates that the vacuum
B
will start automatically when the
power tool is activated.
When the power tool is turned off,
the vacuum motor will continue to
run for 6 to 10 seconds to finish
collecting the dust, and then it will
stop.
Fig. 5
9
Download from Www.Somanuals.com. All Manuals Search And Download.
PARKING BRAKE
Both models are equipped with a Parking Brake. The parking brake will lock
one wheel to prevent the vacuum from rolling.
To engage parking brake, use your toe to depress the brake button. The
brake will snap into the locked position.
To disengage parking brake, use your toe to pull up on the brake button until
it snaps into the unlocked position.
TOP FILTER
Both models are equipped with a top filter. If vacuum efficiency is reduced
(indicating a clogged filter), proceed as follows:
1. Turn the Vacuum Cleaner “OFF.” Grasp handle (C) Fig. 6 and pull out
(approximately one and one-half inches), then release. Repeat several
times. This action “shakes” the filter to remove loose dirt.
2. Turn the Vacuum Cleaner “ON” and check performance. If still unsatis-
factory, turn the Vacuum Cleaner “OFF” and continue to step 3.
C
Fig. 6
Fig. 7
3.
DISCONNECT APPLIANCE FROM POWER
CIRCUIT.
4. Pull upward on the filter cover lock, located on rear of the motor unit
(see Fig. 7) to expose the filter.
5. Remove the filter (see Fig. 8) and tap it to remove any loose dirt.
6. If the filter is still dirty, clean it under running water (see Fig. 9). If this
does not adequately clean the filter, replace it.
NOTE: Allow wet filter to dry before re-installing it in the appliance.
Fig. 9
Fig. 8
10
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: A small sponge filter is located next to the top filter. This
filter helps to cool the motor. Check the filter on a regular basis. If it
is dirty, clean it by blowing dry compressed air through it.
DRY PICK-UP
Do not pick up anything that is burning,
smoldering, or smoking such as matches, cigarettes, or hot ashes.
Do not use to vacuum combustible explosive materials, such as
coal, grain, or other finely divided combustible material.
Do not use to vacuum hazardous, toxic, or carcinogenic materials,
such as asbestos, pesticide or lead-based paint debris.
The vacuum cleaner may be used to pick up dry material with or without a
dust bag installed. The dust bag provides a convenient method for disposing
of the material that is collected.
Always use a dust bag when collecting fine dust. The bag will reduce
clogging of the flat filter, and increase dust holding capacity.
WET PICK-UP
Never pick-up explosive liquids (e.g. gasoline,
diesel fuel, heating oil, paint thinner, etc.), acids or solvents.
Always remove paper bag before picking up liquids or wet material. The
vacuum motor will shut off automatically when the container is full. Turn the
Vacuum Cleaner “OFF” before emptying container.
DISCONNECT APPLIANCE FROM POWER
CIRCUIT BEFORE REMOVING POWER UNIT FROM CONTAINER.
A
Fig. 10
Fig. 11
The Model 7814 has a drain hose located at the rear of the container.
Remove the hose from its holder and point it downward to drain the
container (see Fig. 10).
Always clean and dry the interior of the container after using the machine for
wet pick-up. Also clean the two brass colored electrodes (see Fig. 11), on
the bottom of the motor unit. These electrodes are part of the low-voltage
system that stops the vacuum motor when the container is full of liquid or
wet material.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
list of service centers or call the Porter-Cable help line at 1-800-487-8665.
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts
should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic
parts. They could possibly dissolve or otherwise damage the material.
Wear ANSI Z87.1 safety glasses while using
compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord plug are
making good contact in the outlet. Also, check for blown fuses or open circuit
breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant for
the life of the unit under normal operating conditions. No further lubrication is
necessary.
BRUSH INSPECTION (If applicable)
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA FACTORY
SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and inspected.
Have worn parts replaced and lubricated with fresh lubricant. Have new brushes
installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the need
for immediate servicing of your tool. DO NOT CONTINUE TO OPERATE TOOL
UNDER THIS CONDITION. If proper operating voltage is present, return your tool
to the service station for immediate service.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
REPLACEMENT PARTS
When servicing use only identical replacement parts. For a service parts list or to
learn more about Porter-Cable visit our website at www.porter-cable.com
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to
wear from normal use. For assistance with your tool, visit our website at
www.porter-cable.com for a list of service centers or call the Customer Care
Department at 1-800-487-8665. All repairs made by our service centers are fully
guaranteed against defective material and workmanship. We cannot guarantee
repairs made or attempted by others.
Should you have any questions about your tool, feel free to write us at any time.
In any communications, please give all information shown on the nameplate of
your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•Delta
Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-Cable
Authorized Service Stations. Please visit our Web Site www.porter-cable.com
for a catalog or for the name of your nearest supplier.
Since accessories other than those offered by Porter-
Cable•Delta have not been tested with this product, use of such accessories
could be hazardous. For safest operation, only Porter-Cable•Delta
recommended accessories should be used with this product.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
GEORGIA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
OREGON
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
ILLINOIS
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
PENNSYLVANIA
St. Louis 63119
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Diego 92111
7638 Clairemont Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
NEW YORK
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MARYLAND
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
COLORADO
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
FLORIDA
WASHINGTON
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
•
•
•
•
•
•
•
•
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
7.2-PTG-F-1
Download from Www.Somanuals.com. All Manuals Search And Download.
|