2006 LCD Models – North America
FLM-2632, FLM-2632M, FLM-2634B, FLM-3232, FLM-3232M, FLM-323B,
FLM-3234B, FLM-3732, FLM-3732M, FLM-373B, FLM-3734B, FLX-374
SERVICE MANUAL
Bezel covers vary by model
20070411
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Service and Safety Information
Service work should be performed only by qualified service technicians familiar with all safety
checks and these service guidelines:
ELECTRIC SHOCK HAZARD
Always disconnect AC power before servicing!
Never modify any circuit!
Never insert any objects into the holes in the TV case!
ELECTROSTATIC DISCHARGE (ESD)
Components inside an LCD or plasma TV are sensitive to static electricity. Before servicing the TV, follow these
guidelines:
• Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.
• Remove replacement components from their antistatic bags only when you are ready to use them. Do
not lay components on the outside of antistatic bags because only the inside of the bags provide
electrostatic protection.
• Always hold components by their edges. Avoid touching the edge connectors. Never slide components
over any surface.
• Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of
your workbench or other grounded connection.
• Touch a bare metal surface on your workbench or other grounded object before touching any
components.
PRECAUTIONS FOR USING LEAD-FREE SOLDER
Components within this television use lead-free solder (Sn-Ag-Cu). Look at the markings on board and
components within the television to determine the correct solder type and match to the table below:
5 LEAD-FREE (Pb-Free) CATEGORIES
The following categories are meant to describe the Pb-free 2nd level interconnect terminal
finish, component material, and/or the solder paste/solder used in board assembly:
e1 - SnAgCu (shall not be included in category e2)
e2 - Sn alloys with no Bi or Zn excluding SnAgCu
e3 - Sn
e4 - Precious metal (e.g., Ag, Au, NiPd, NiPdAu) (no Sn)
e5 - SnZn, SnZnx (no Bi)
e6 - contains Bi
e7 - low temperature solder (≤ 150 °C) containing Indium (no Bi)
e0, e8, e9 symbols are unassigned at this time.
When repairing components soldered with lead-free solder, ONLY use lead-free solder that matches the
symbol on the component. Using conventional lead solder may lead to damage or a short, which could result
in fire, electric shock, or other hazards.
Because the melting point of lead-free solder is higher than conventional lead solder, observe the following
guidelines when soldering with lead-free solder:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Always use a dedicated soldering bit for different types of solder. If a different type of solder comes in contact with
a lead-free solder bit, subsequent solder joints will no longer be lead free. Always clean the soldering bit after
every use.
(2) Keep the soldering bit in contact with the just long enough to confirm a good solder joint. Leaving the bit in contact
with parts for an extended period may damage the components.
(3) Because lead-free solder contains a higher concentration of tin, the tip of the soldering bit may be easily corroded
or damaged. Do not leave the bit powered on for extended periods. When the tip of the soldering bit is blackened
during use, clean the bit with steel wool or fine sandpaper. (0)
NOTICE ABOUT REPLACEMENT PARTS
Many electrical and mechanical parts within LCD or plasma televisions are chosen for their
specific safety characteristics within the overall system. Replacing individual parts with
components rated for higher voltage or wattage can be dangerous!
Replacement parts must always be identical to those originally used in the television. Unauthorized substitute
parts may result in fire, electric shock, or other hazards.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Polaroid Display Cell Defect Specification........................................................................................ 18
Before Returning This Product to the User...................................................................................... 19
Disassembly Procedure.................................................................................................................. 20
Rear Cabinet Cover LCD Panel and Front Bezel.......................................................................... 23
Front/Side Control Buttons Removal and Replacement............................................................... 31
Exploded View Diagram................................................................................................................. 39
PCB Layout Diagrams.................................................................................................................... 51
Model Specifications are located in User Manual. Go to polaroid.com to obtain User Manual.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Original Remote Control
8
Download from Www.Somanuals.com. All Manuals Search And Download.
New Remote Control
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory Mode Procedure
1. Power on TV.
2. Press volume up and channel up buttons on the TV simultaneously and release.
3. Power off TV with remote or power button to exit.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
The operation of each OSD control is described in the following table:
Menu
VIDEO
Options
Picture Mode
Sub-Options
Vivid →Hi-Bright
→Cinema
Function and Description
Press repeatedly for different picture
modes: Vivid →Hi-Bright →Cinema→Sport
→User.
→Sport→User.
Contrast
Brightness
Saturation
Hue
Sharpness
Color Temperature Cool
Nature
0…100 (75)
0…100 (50)
0…100 (50)
-30…+30 (0)
0…7 (4)
Fine tune the contrast.
Fine tune the brightness.
Fine tune the contrast.
Fine tune the contrast.
Fine tune the contrast.
Set the color temperature type.
Warm
User
Red/Green/Blue: -19…+19
Fine tune the bass value.
Fine tune the treble value.
Fine tune the balance value.
Select the preset effect mode to match
your music type and achieve stunning
effects.
AUDIO
Bass
0…100 (50)
0…100 (50)
-20…+20 (0)
Live
Treble
Balance
Effect
Dance
Techno
Classic
Soft
Rock
POP
Off
Close this function.
MTS
Mono
Stereo
Sap
Set the sound type, which is only
available when input source is TV.
Auto Search
Tuner Mode
Auto search
channels.
Cable-STD / Cable-
HRC / Cable-IRC
Air
Auto-search channels and put the
programs into memory.
Select the tuner mode.
TV
Channel Skip
Set the channel that
you want to skip.
If a channel is set to SKIP, when
scanning up/down channels the
selected channel will be skipped.
It will be invalid if the current input
source is not TV.
Channel Name
Language
Timer
Edit the channel
name.
English/
Spanish/French
Time
SETUP
Set language.
Input current time
Start Time
Stop Time
Channel
Input the TV start playing time.
Input the TV stop playing time.
Input the channel No. for desired TV
program.
Activate
Display
On/Off/Once
On/Off
Set the timer alarm on/off.
Preset the auto sleep time. The TV will
automatically go into standby state
when the preset time is up.
Set auto sleep function off.
Auto Sleep
30,60,90,120 Min
Off
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Caption
V-chip
C1,C2,C3,C4,T1,T2,
TT4,and Off
Set the closed caption mode.
Input Password
Block MPAA Rating
Input the 4-digit password. “0000”
Set the input source that you want to
lock.
Block TV Rating
Input the old password first, and then
input the new password.
Block MPAA Unrated
Block all unrated movies.
Block TV None Rating Block all unrated TV programs.
Reset
Reset to default
value.
Reset the items in the setup menu
except the protected items.
Audio Language
Time Zone
To set the audio language to English,
French, or Spanish.
Set the Time Zone value to Eastern
Time, Indiana, Central Time, Mountain
Time, Arizona, Pacific Time, Alaska
and Hawaii.
HDTV
Auto Scan
Auto-search channels and put the
programs into memory.
Manual Scan
Add-on mode: To search channels that
had not searched last time.
Range mode: To search receivable
channels in the setting range.
If a channel is set to SKIP, when
scanning up/down channels the
selected channel will be skipped.
Channel Skip
Analog Closed
Caption
Set the analog closed caption value to
OFF,CC1,CC2,CC3,CC4,TEXT1,TEXT2,
TEXT3 and TEXT4.
Digital Closed
Caption
Set the digital closed caption value to
OFF, Service1, Service2, Service3,
Service4, Service5 and Service6.
To set the values of caption style.
Digital Caption
Style
Block Channel
To setup the block channel.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Troubleshooting / Flow Charts
Note: Reseat all cables, check fuse by AC plug, perform a clear or reset in factory mode and
retest before ordering parts.
Can’t power on your TV?
This TV is equipped with a safety fuse. In the event of an electrical storm or power outage the safety fuse is
designed to protect your TV. If your TV has no power, check the fuse by prying the cover off, following the
illustration below. If the fuse is blown, visit your local hardware store and ask for a 4A 250V - 5x20mm Time
Lag Fuse (Slow Blow) to replace the fuse.
Having trouble with setting your Parental Controls (V-Chip)?
The factory preset password is 0000. This password must be used first before setting your own personal
password. It is recommended that you keep your personal password in a safe place and away from children.
In the event you loose your personal password the master password is 8202. The master password overrides
all passwords. The master password can’t be changed and should be kept in a safe place away from children.
Having trouble with setting Picture-in-Picture settings?
The Picture-in-Picture will not work using Component 1 and Component 2 as the input sources.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Polaroid Display Cell Defect Specification
In some cases, a panel may have defective cells that cannot be controlled.
These defective cells can be categorized into two types;
(1) Non-lighting or dark cell defect: defect in which the cell is always off
(2) Non-extinguishing or bright cell defect: defect in which the cell is always on
The Polaroid Display Cell Defect Specifications below define the allowed limits for display cell defects and are
used as the criteria in determining whether an LCD panel is replaced.
7 or more defective pixels across the entire LCD screen Polaroid will repair (replace LCD panel) or replace the
TV.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Before Returning This Product to the User
Before returning this product to the user, always perform the following safety checks:
(1) Inspect all wiring to be sure no wires are pinched between the chassis or any metal parts.
(2) Inspect all protective devices for proper installation, including non-metallic controls, insulation materials, cabinet
backs, compartment covers, and shields.
(3) Verify that no shock hazard exists on any part of the chassis, especially any metal components including cable
connection points, chassis hardware, or antennas (if equipped). Use the following procedure:
a. Plug the AC cord directly into a 120 V AC outlet.
b. Create a test circuit consisting of a 1.5k ohm, 10
watt resistor paralleled by a 0.15 µF capacitor.
c. Using an AC voltmeter (sensitivity of 5000 ohm per
volt or higher), measure the voltage drop across
the test circuit between all exposed metallic parts
and a known earth ground. Measurement points
include antenna, metal cabinet parts, screw heads,
and metal knobs or controls. Measurement points
can vary slightly even between revisions of the
same model, so always conduct a thorough review
of the chassis to locate metal points that a user
may touch.
d. Any voltage reading of 0.375 Vrms AC (0.25
mArms) or higher indicates a potential shock
hazard. THIS CONDITION MUST BE
CORRECTED BEFORE RETURNING THE
PRODUCT TO THE USER!
e. Repeat the above checks with the AC polarity
reversed. A non-polarized adapter is required to
reverse the polarity; DO NOT LEAVE THIS
ADAPTER WITH THE USER! Under normal
operation the product must use the proper polarity.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Disassembly Procedure
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
When servicing an LCD or plasma TV, always observe the following safety guidelines:
• Wear a grounding (ESD) wrist strap, and use a grounded or dissipative work mat.
• Use a stable and strong work surface that is large enough to hold components you might remove.
• When removing components that are attached with a cable, unplug the cable before removing the
screws to avoid damaging the cable.
• Use a magnetized screwdriver for removing screws.
• To help keep track of screws, place each component’s screws next to the component on your work
surface.
ELECTROSTATIC DISCHARGE (ESD)
Components inside an LCD or plasma TV are sensitive to static electricity. Before servicing the TV, follow these
guidelines:
• Avoid static-causing surfaces such as carpeted floors, plastic, and packing foam.
• Remove replacement components from their antistatic bags only when you are ready to use them. Do
not lay components on the outside of antistatic bags because only the inside of the bags provide
electrostatic protection.
• Always hold components by their edges. Avoid touching the edge connectors. Never slide components
over any surface.
• Wear a grounding wrist strap (available at most electronics stores) and attach it to a bare metal part of
your workbench or other grounded connection.
• Touch a bare metal surface on your workbench or other grounded object before touching any
components.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Cover Removal
Lay TV flat on workbench. Be careful to protect the front bezel and LCD screen from being scratched. Use
protective cloth between work bench and TV front.
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
Stand Removal
(1) Lay TV flat on workbench. Be careful to protect the front bezel and LCD screen from being scratched. Use
protective cloth between work bench and TV front.
(2) Remove screws in the sequence indicated below (1 thru 6).
(3) Remove stand.
*NOTE: Pictured is a 26” model. 32” and 37” models will have different stand screw
quantities and locations.
Rear Cover Removal
(4) Remove control box cover screws (PIC1 item 1, 2)
(5) Remove control box cover screws (PIC1 item 3)
(6) Remove control box cover- slide toward bottom of TV and lift off.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
(7) Lift up the control box from the A/V connector side (PIC1). There are cables underneath that are connected so be
careful. Release control box from back hinges and tilt to the left (PIC3).
(8) Tear off the Aluminum foil covering the LVDS connector. Disconnect LVDS cable connector from LCD panel (PIC2).
(9) Disconnect the LCD Panel power cord from bottom side of control box
(PIC3).
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Cabinet Cover LCD Panel and Front Bezel
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
Note: OEM LCD panels were used in production. The following LCD panel
disassembly/removal instructions may not apply to all models. Ensure LCD panel is
completely detached from the bezel before removing so the bezel is not damaged.
(1) Remove screws (PIC1) in the sequence of 1, A.
(2) Remove screws (PIC1) in sequence of 2, 3, 4, B, C, D
(3) Remove screws which fasten rear cabinet to front frame (PIC1) in the following sequence: AÆBÆCÆDÆEÆF
then 1Æ2Æ3Æ4Æ5
(4) Remove rear cabinet cover. Only the rear cabinet cover will come off.
*NOTE: Pictured is a 26” model. 32” and 37” models will have some different rear cabinet
cover screw quantities and locations.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Remove screws from TV stand support frame (PIC1)
(6) Remove screws from TV stand support frame (PIC1).
(7) Remove TV stand support frame.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
(8) Remove the EMI Aluminum Foil Sheilding Tape from the LCD Panel (PIC1, 2)
(9) EMI Aluminum Foil Sheilding Tape must be replaced during assembly.
Remove the EMI Aluminum
Foil Shielding Tape which
secures the Keyboard wiring
to the panel.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
(10) Remove from the D-sub board Speaker wire, Front/Side Control Button wire, and A/V wire connectors (PIC1)
(11) Remove the black tape from the Speaker wire and Ceramic ring (PIC2)
(12) Replace black tape during assembly.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
(13) Remove the foam spacer from LCD Panel and remove the A/V wire under the frame (PIC1).
(14) Save foam spacer and place in position during assembly.
(15) Remove the A/V subassembly from the bezel (PIC2).
(16) Remove screws (PIC1) in the sequence: 1-2
(17) Disconnect the LCD Panel cable from the D-SUB board (PIC1)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
(18) Remove screws that secure the LCD panel to the bezel (PIC1, PIC2)
(19) TWO MEN REQUIRED!! Lift LCD Panel from the bezel
(20) Replace LCD panel.
(21) The front bezel can now be replaced if needed.
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
A/V Board Removal and Replacement
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
(1) Disassemble control box cover and rear cabinet cover and remove A/V assembly.
(2) Using a small pair of wire cutters grip the side-locking tab and pivot back towards the A/V cable connector (PIC1).
Locking tabl should only pivot about 45 degrees. Do the same for the opposite side of the A/V assembly.
(3) Slide out A/V board and replace (PIC2).
(4) Push locking tabs in to secure replaced A/V board.
PIC1
PIC2
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
IR Board Removal and Replacement
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
(1) Disassemble rear control box cover and rear cabinet cover.
(2) 2. Remove screws 1 and 2 and replace IR board (PIC1).
PIC1
PIC1
2
1
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Front/Side Control Buttons Removal and Replacement
Note: Before disassembly of any part the TV, make sure the power is OFF, and the
power cord is removed from the wall outlet. Allow time for power within all system
boards to discharge before you begin disassembly. Never insert any objects into the
vent holes in the TV case.
(1) Disassemble control box cover and rear cabinet cover.
(2) The control button board is attached with glue. Use alcohol to soften the glue and remove the control button
board (PIC1).
(3) Replace control button board and use glue to fasten to front bezel.
PIC1
Note: Before returning this product to the end user, you must follow the steps
procedure ensures that the chassis will not cause electric shock.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Spare Parts Lists – FLM-Series 26, 32, 37
Attention Service Centers
Some models consist of parts with multiple versions. Replacement parts in the spare part lists with an asterisk
(*) are multiple version parts. The TV serial number Model Version is used to identify the replacement part(s)
needed for repair. Below is the Polaroid serial number format breakdown with a sample serial number.
Reference the serial number format details below to identify the correct replacement part(s) before placing
replacement part orders.
In the event the TV Model Version is not present in the part lists please review service bulletins for this model.
Service bulletins can be obtained through your Polaroid service contact.
SAMPLE SERIAL NUMBER FORMAT - DETAILS
C
0
6
0
0
0
1
2
7
2
0
0
0
0
0
0
1
Month of Production
Year of Production
Model Version
Unique 7 digit Serial Number
Non RoHS Serial Number Example - C0600012720000001
RoHS Compliant Serial Number Example - CR600012720000001 - the 0 in Year of Production is replaced with R.
Production Month Designators:
A = January
B = February
C = March
D = April
E = May
F = June
G = July
H = August
J = September
K = October
M = November
P = December
Note: Reseat all cables, check fuse by AC plug, perform a clear or reset in factory mode and
retest before ordering parts.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-323B Part List
Model Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
621-181-2000H
621-181-3020P-1H
845-C45-GF1XA-PH
AC Power Cord
Audio Cable
Composite Video Cable
Component Cable
Remote Control
00, 01, 02, 03, 04,
06
A6
*909-KS0-GF321XA
*909-KE0-GF321XAH
*909-KQ0-
Control Box Assembly (CMO L01)
Control Box Assembly (AUO V0)
C1, C2, C3, C6
GF321XA3H
Control Box Assembly (QDI)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
Front/Side A/V Input Bd.
00, 01, 02, 03, 04,
06
A6
*705-532-050C-4AH
*705-532-050A-V5H
*705-532-001QTH
*705-132-HA32H
32" LCD Panel (CMO L01)
32" LCD Panel (AUO V0)
32" LCD Panel (QDI) (F1)
32" LCD Panel (QDI) (F2)
C1, C2, C3, C6
C1, C2, C3, C6
00, 01, 02, 03, 04,
06
A6, C1, C2, C3, C6 *151-113-FPH8BEH
151-002-FPH7GH
*151-103-FPH8BH
Front Bezel Black/Silver (CMO L01)
Front Bezel Black/Silver (QDI) (AUO)
Rear Cabinet Black
154-004-GF32WH
151-700-GF321XAH
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
824-015-GF321L-KH
Speaker (right or Left)
00, 01, 02, 03, 04,
06
*631-030-GF321XAH
LVDS Cable (CMO )
A6, C1, C2, C3, C6 *631-030-GF321-A5H
631-012-GF321H
LVDS Cable (AUO QDI)
Power Inverter Cable (AUO CMO QDI)
*Note - Model Version column - see “Attention Service Centers” info before ordering part.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-373B Part List
Model Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
*909-KS0-GF371XAH
*909-TE1-GF378XCH
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
*705-137-G01AH
*705-537-401AX1H
*705-537-401A0H
*151-113-FC58BH
*151-103-FC58BH
151-002-FC57GH
154-004-GF32WH
151-700-GF371XAH
824-015-GF321L-KH
*631-030-JK378H
*631-030-GF371XAH
00, 01, 02, 03, A1, 23
12, 13, A2
Control Box Assembly (AUO V1 V2)
Control Box Assembly (AUO V0)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
37" LCD Panel (AUO V2)
37" LCD Panel (AUO V1)
37" LCD Panel (AUO V0)
Front Bezel Black/Silver (AUO V2)
Front Bezel Black/Silver (AUO V0 V1)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
LVDS Cable (AUO V0)
LVDS Cable (AUO V1 V2)
23
A1
12, 13, A2
23
12, 13, A1, A2
12, 13, A2
00, 01, 02, 03, A1, 23
*Note - Model Version column - see “Attention Service Centers” info before ordering part.
Polaroid FLM-2632 Part List
Model
Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-B45-GF1XA-PH
*909-KC0-GF271XA-3H
*909-KS0-GF271XAH
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
*705-526-002CH
*705-526-051C-1H
*151-113-FL98BH
*151-103-FL98BH
151-002-FL97GH
03
00, 01, 04
Control Box Assembly (CMO L03)
Control Box Assembly (CMO L01)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
26" LCD Panel (CMO L03)
26" LCD Panel (CMO L01)
Front Bezel Black/Silver (CMO L03)
Front Bezel Black/Silver (CMO L01/L03)
Rear Cabinet Black
03
00, 01, 04
03
00, 01, 04
154-004-GF32WH
151-700-GF271XAH
824-015-GF271H
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
03
00, 01, 04
*631-030-GF321XA-04H
*631-030-GF321XAH
631-N28-GF321XAH
LVDS cable (CMO L03)
LVDS Cable (CMO L01 , L03)
Power Inverter Cable (CMO L01, L03)
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-2632M Part List
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-B45-GF1XA-PH
909-KS0-GF271XAH
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
705-526-051C-1H
151-103-FL98BH
151-002-FL97GH
154-004-GF32WH
151-700-GF271XAH
824-015-GF271H
631-030-GF321XA-04H
631-030-GF321XAH
631-N28-GF321XAH
Control Box Assembly (CMO L01)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
26" LCD Panel (CMO L01)
Front Bezel Black/Silver (CMO L01/L03)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
LVDS cable (CMO L03)
LVDS Cable (CMO L01 , L03)
Power Inverter Cable (CMO L01, L03)
*Note - Model Version column - see “Attention Service Centers” info before ordering part.
Polaroid FLM-2634B Part List
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-B45-GF1XA-PH
909-KS0-GF271XAH
899-K00-GF271XAH
154-500-GF321H
899-E00-GF271XAH
899-A00-GF271XAH
705-526-051C-1H
151-103-FL97WH
151-002-FL97GH
154-004-GF32WH
151-701-GF271XAH
824-015-GF271H
631-030-GF321XAH
631-N28-GF321XAH
Control Box Assembly (CMO L01)
Front/Side Control Button Bd.
Front/Side Control Button Cover Black
IR Board
Front/Side A/V Input Bd.
26" LCD Panel (CMO L01)
Front Bezel Black/Black (CMO L01)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Black
Speaker (right or Left)
LVDS Cable (CMO L01 , L03)
Power Inverter Cable (CMO L01, L03)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-3232 Part List
Model
Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
*909-KS0-GF321XA
*909-KE0-GF321XAH
*909-KQ0-GF321XA3H
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
*705-532-050A-V5H
*705-532-050C-4AH
*705-532-001QTH
*705-132-HA32H
*151-103-FPH8BH
*151-000-FPH8BEH
*151-110-FPH8BEH
151-002-FPH7GH
154-004-GF32WH
151-700-GF321XAH
824-015-GF321L-KH
*631-030-GF321XAH
*631-030-GF321-A5H
631-012-GF321H
00, 01, 02, 06
A3
C3
Control Box Assembly (CMO L01)
Control Box Assembly (AUO V5)
Control Box Assembly (QDI)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
32" LCD Panel (AUO V5)
32" LCD Panel (CMO L01)
32" LCD Panel (QDI) (F1)
32" LCD Panel (QDI) (F2)
Front Bezel Black/Silver (CMO L01)
Front Bezel Black/Silver (AUO V5)
Front Bezel Black/Silver (QDI)
Rear Cabinet Black
A3
00, 01, 02, 06
C3
C3
00, 01, 02, 06
A3
C3
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
LVDS Cable (CMO L01 )
LVDS Cable (AUO QDI)
Power Inverter Cable (AUO CMO QDI)
00, 01, 02, 06
A3, C3
*Note - Model Version column - see “Attention Service Centers” info before ordering part.
Polaroid FLM-3232M Part List
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
909-KS0-GF321XA
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
705-532-050C-4AH
151-103-FPH8BH
151-002-FPH7GH
154-004-GF32WH
151-700-GF321XAH
824-015-GF321L-KH
631-030-GF321XAH
631-012-GF321H
Control Box Assembly (CMO L01)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
32" LCD Panel (CMO L01)
Front Bezel Black/Silver (CMO L01)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
LVDS Cable (CMO L01 )
Power Inverter Cable (AUO CMO QDI)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-3234B Part List
Model
Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
*909-KS0-GF321XA
*909-KQ0-GF321XA3H
899-K00-GF271XAH
154-500-GF321H
899-E00-GF271XAH
899-A00-GF271XAH
*705-532-050C-4AH
*705-532-001QTH
*705-132-HA32H
*151-114-FPH7WJH
*151-113-FPH7WEH
151-002-FPH7GH
154-004-GF32WH
151-701-GF321-XAH
824-015-GF321L-KH
*631-030-GF321XAH
*631-030-GF321-A5H
631-012-GF321H
00, 01, 03
C3
Control Box Assembly (CMO L01/L04)
Control Box Assembly (QDI)
Front/Side Control Button Bd.
Front/Side Control Button Cover Black
IR Board
Front/Side A/V Input Bd.
32" LCD Panel (CMO L01/L04)
32" LCD Panel (QDI) (F1)
32" LCD Panel (QDI) (F2)
Front Bezel Black/Black (CMO L01/L04)
Front Bezel Black/Black (QDI)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Black
Speaker (right or Left)
LVDS Cable (CMO L01)
LVDS Cable (AUO QDI)
Power Inverter Cable (AUO CMO QDI)
LVDS CBL (CMO-L04)
00, 01, 03
C3
C3
00, 01, 03
C3
00, 01
C3
03
*631-030-GF321XA-04A
*Note - Model Version column - see “Attention Service Centers” info before ordering part.
Polaroid FLM-3732/3732M Part List
Model
Version
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
*909-KS0-GF371XA
*909-TE1-GF378XCH
899-K00-GF271XAH
154-501-GF370-AH
899-E00-GF271XAH
899-A00-GF271XAH
*705-537-401A0H
*705-537-401AX1H
151-103-FC58BH
151-002-FC57GH
154-004-GF32WH
151-700-GF371XAH
824-015-GF321L-KH
*631-030-GF371XAH
*631-030-JK378H
00, 01, 02, 03
12
Control Box Assembly (AUO V1)
Control Box Assembly (AUO V0)
Front/Side Control Button Bd.
Front/Side Control Button Cover Silver
IR Board
Front/Side A/V Input Bd.
37" LCD Panel (AUO V0)
37" LCD Panel (AUO V1)
Front Bezel Black/Silver (AUO V0, V1)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Silver
Speaker (right or Left)
LVDS Cable (AUO V1, V2)
LVDS Cable (AUO V0)
12
00, 01, 02, 03
00, 01, 02, 03
12
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Polaroid FLM-3734B, FLX-374 Part List
Part Number
Description
600-181-3200-LIH
621-181-60002H
AC Power Cord
Audio Cable
621-181-2000H
Composite Video Cable
Component Cable
Remote Control
621-181-3020P-1H
845-C45-GF1XA-PH
909-KS0-GF371XA
899-K00-GF271XAH
154-500-GF321H
899-E00-GF271XAH
899-A00-GF271XAH
705-537-401AX1H
151-103-FC57WH
151-113-FC57WH
151-002-FC57GH
154-004-GF32WH
151-701-GF371XAH
824-015-GF321L-KH
631-030-GF371XAH
Control Box Assembly (AUO V1)
Front/Side Control Button Bd.
Front/Side Control Button Cover Black
IR Board
Front/Side A/V Input Bd.
37" LCD Panel (AUO V1)
Front Bezel Black/Black (AUO V1)(F1)
Front Bezel Black/Black (AUO V1)(F2)
Rear Cabinet Black
Rear Cabinet Control Box Cover Black
Stand Assembly Black
Speaker (right or Left)
LVDS Cable (AUO V1 V2)
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Number: FLM-3232, FLM-323B, FLM-3232M, FLM-3234B
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Number: FLM-3732, FLM-373B, FLM-3732M, FLM-3734B, FLX-374
41
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Schematics
HMDI connector is a type A receptacle for video/audio mode.
1. TMDS Data 2+
2. TMDS Data 2 shield
3. TMDS Data 2-
4. TMDS Data 1+
5. TMDS Data 1 shield
6. TMDS Data 1-
9. TMDS Data 0-
10. Clock +
11. Clock shield
12. Clock -
13. CEC
14. NC
17. CEC/GND
18. +5V Power
19. Hot Plug Detect
7. TMDS Data 0+
8. TMDS Data 0 shield
15. DDC CLK
16. DDC DATA
D-Sub Connector IN. (This function also can provides to HDTV.)
D-Sub type Connector pin assignment
1. Red Video
6. Red Ground
7. Green Ground
8. Blue Ground
9. +5V from PC
10. Sync. GND
11. GND
2. Green Video
3. Blue Video
4. GND
12. SDA For DDC1/2B
13. H-sync.
14. V-sync.
5. Vdd from PC for DDC
15. SCL For DDC1/2B
RCA jacks are all female type.
Mini DIN CNC 4 Pins (SCN570S3NS00000) for S-video, the pin assignment is described as below:
1: Ground
2: Ground
3: Y
4: C
43
Download from Www.Somanuals.com. All Manuals Search And Download.
HDMI
Format
DVI 1.0
Level/Impedance
TMDS Mode
Frequency
0.5~3.0Vp-p/100 Ohm (Differential),50 Ohm (Single ending)
Single Link
Fh = 31~80 kHz
Fv = 56~76 Hz
Maximum Pixel Clock
DDC 1/2B
135 MHz
Compliant with Revision 1.0
HDMI x 1
Connector
Analog HD15 PC Signal (RGB)
R, G, B Analog
Format
Level/Impedance
DDC 1/2B
0.7Vp-p / 75Ω
Compliant with Revision 1.0
H/V separate
Sync
3V TTL level / 1kΩ
Fh = 31~80 kHz
Fv = 56~76 Hz
Frequency
Maximum Pixel Clock
Connector
135 Mhz
Mini D-Sub 15 pin (female) x 1
Video (Composite) CVBS Signal
NTSC, 4.43NTSC, PAL_M, PAL(B,G,H,D,N), SECAM
1.0Vp-p / 75Ω
Format
Level / Impedance
S-Video (Y/C) Signal
Y, C
Format
Level / Impedance
Y: 1.0Vp-p / 75Ω
C: ± 286 mV/ 75Ω
Analog HD15 Video Signal (YPbPr/YCbCr)
Format
Y, Pb, Pr or Y, Cb, Cr
Level / Impedance
Y: 1.0Vp-p / 75Ω
Pb/Cb, Pr/Cr: 0.7 ± 0.035Vp-p / 75Ω
HDMI Timing
V FREQ
Hz
H FREQ
kHz
CLK
MHz
STANDARD
RESOLUTION
ATSC, 480i
ATSC, 480p
ATSC, 1080i
ATSC, 720p
ATSC, 576i
720x480
720x480
1920x1080
1280x720
720x576
60
60
60
60
50
15.7
31.5
33.7
45.0
15.6
27
27
74.2
74.2
27
44
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB PC Timing
V FREQ
H FREQ
kHz
CLK
MHz
STANDARD
RESOLUTION
Hz
VGA
640x480
640x480
800x600
800x600
1024x768
1024x768
1280x1024
1280x1024
640x480
720x400
60
31.47
37.5
37.88
46.9
48.36
60.02
64
25.16
31.5
40
VGA
75
60
75
60
75
60
75
67
SVGA
SVGA
XGA
49.5
65.0
78.75
108
XGA
SXGA
SXGA
MAC
80
135
35
30.24
28
Non-VESA
70
31.5
Video & S-Video AV Timing
V FREQ
H FREQ
kHz
CLK
MHz
STANDARD
RESOLUTION
525
Hz
NTSC
60
50
50
60
60
50
15.734
12.65
14.50
14.50
12.65
12.65
14.50
PAL(B,G,H,D,I)
SECAM
625
625
525
525
625
15.625
15.625
15.734
15.734
15.625
4.43NTSC
PAL-M
PAL-N
HDTV/Component AV Timing
SDTV 525i
SDTV 625i
SDTV 480p
HDTV 720p
HDTV 1080i
720x525
720x625
720x480
1280x720
1920x1080
60
50
60
60
60
15.735
27
27
15.625
31.5
27
50.0
74.2
74.2
33.7
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Source
Sound Output
AC100 – 240 V, 60/50 Hz
10W X2, 8 Ohm.
Signal Connector Pin Assignment
Pin
1.
Assignment
Red
Pin
6.
Assignment
Pin
Assignment
Ground
SDA
Red Ground
11.
2.
Green
7.
Green Gro und 12.
Horizontal
Sync.
3.
Blue
8.
Blue Ground
13.
15.
Vertical
Sync.
14.
4.
5.
Ground
9.
Not Connected
Sync. Ground
Self Test
10.
SCL
46
Download from Www.Somanuals.com. All Manuals Search And Download.
IR Board
VCC
VCC
VCC
C1
R1
100
R2
10K
0.1uF
U1
3
2
1
J1
V
G
O
VCC
1
2
3
4
5
IR-OUT
LED_O
LED_G
GND
C2
IR-SENSOR
10uF-0805
CON5
Hous5P-1.0h
VCC
R3
560
LED_O
Q1
B
R4
47
MMBT3904
C
D1
VCC
MMBT3904
DIP LED-D3
B
E
R5
P
560
6F
Ta
LED_G
Te
Q2
B
R6
47
MMBT3904
Titl
Siz
A
Da
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Front/Side Control Buttons
VCC
C1
R1
R2
R3
R4
R5
R6
R7
0.1uF
4.7K
4.7K
4.7K
4.7K
4.7K
4.7K
4.7K
J1
1
VCC
POWER-ON
SOERCE
MENU
SW1
2
3
4
5
6
7
8
9
POWER-ON
SW2
CH-UP
CH-DOWN
VOL-UP
VOL-DOWN
GND
SOURCE
SW3
MENU
CON9
SW4
Hous 9P-1.0
CH-UP
SW5
CH-DOWN
SW6
VOL-UP
SW7
VOL-DOWN
ZD1
5.6V
ZD2
5.6V
ZD3
5.6V
ZD4
5.6V
ZD5
5.6V
ZD6
5.6V
ZD7
5.6V
48
Download from Www.Somanuals.com. All Manuals Search And Download.
D-SUB 37 Pin Board (Component Side Top)
D-SUB 37 Pin Board (Component Side Bottom)
52
Download from Www.Somanuals.com. All Manuals Search And Download.
|