IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain these
instructions for the life of the equipment:
Model #: __________________________
Serial #: __________________________
Date Upgraded: ____________________
Technician: ________________________
Installation Instructions for the
PE14D/PG14D
Manual Fill Option
L80-045 Rev 0 (11/07)
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
8
7
9
10
11
12
14
13
Ensure kit is complete. Part number B8702901-CL.
1. Qty.1 B3615401-C
Bezel
2. Qty.3 PP10911
3. Qty.1 A8017902-C
4. Qty.1 PP10830
5. Qty.1 A1826101-C
6. Qty.1 PP10944
7. Qty.1 PP10726
8. Qty.2 PP10270
9. Qty.2 PP10694
9. Qty.4 P0092300
10. Qty.1 A8017501
11. Qty.1 B8029301
12. Qty.1 PP10945
13. Qty.1 A8017401
14. Qty.1 A6066901
Fitting
Bracket
Fitting
Bracket
Knob
Check Valve
U-Bolt
Screw
Nut
Piping
Handle Extension
Valve
Piping
Overlay
L80-045 Rev0 (11/07)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Qty.1 L80045
Instruction Manual
Exploded Part view
L80-045 Rev0 (11/07)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. From the back, remove the eight 5/16” screws that hold the rear cover on.
2. With the rear of the tank exposed, remove the fill port plug with a 1/2” in
wrench. Then remove the reducer with a 7/8” wrench. Save the reducer,
as it will be reused.
3. With the nylon plug exposed it can now be removed. The hole in the tank
is smaller than the coupling. The nylon plug needs to be removed out the
rear. It can be punched out from the front inside of the tank, or pulled
from the rear. The plug will not be reused. Be sure not to damage the
threads of the coupling. Clean any debris from the reducer and the
coupling. Apply Teflon tape to the reducer and reinstall.
L80-045 Rev0 (11/07)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Apply Teflon tape to the 90° compression fitting (PP10911) and install.
Make sure the fitting is at the 3 o’clock position when fully tightened.
5. Apply the compression fitting (PP10830) to the front end of the fill
piping (A8017501) before install. Apply the remaining two 90°
compression fitting (PP10911) to each end of the supply piping
(A8017401). After each end is compressed remove the body of the fitting
6. Install the fill piping from the rear of the unit. The piping should sit on
top of the left tank support. Insert the rear end of the piping in to the rear
compression fitting and tighten the fitting.
L80-045 Rev0 (11/07)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Apply Teflon tape to the rear fitting of the supply piping. Install the
check valve (PP10726) onto the rear fitting of the supply piping with the
support bracket (A1826101-C) between the valve and fitting.
8. Install the supply piping assembly from the front. The assembly should
contain the piping, two fittings, check valve, and mounting bracket.
Mount the bracket to the bottom rear cabinet brace using the two Phillips
head screws (PP10694) and two of the six kep nuts (P0092300). When
mounted, reinstall the rear cabinet cover using the original screws.
L80-045 Rev0 (11/07)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. From the front of the unit, remove the four Allen head screws with a
5/32” Allen Key. Unplug the computer and set front panel assembly
aside. Remove the heat shield via three 5/16” screws.
10.With the heat shield removed remove the no fill option cover plate. The
plate is held in place with three 5/16” screws with 3/8” kep nuts.
11. With the cover removed you should see your supply and fill piping.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Apply Teflon tape the NPT ends of the fitting bodies removed earlier.
Assemble the fittings with fill valve (PP10945). Add the knob extension
to the assembly and install. Make sure the flat side of the “D” shaft faces
the 90° fitting.
12.Install the manual fill option cover plate (A1826101-C) using the original
hardware. Install two the u-bolts (PP10270) and four kep nuts
(P0092300) and tighten.
13.Using a pair of channel locks brake off the extra studs of the U-bolts.
Reinstall the heat shield using the original hardware.
L80-045 Rev0 (11/07)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14.Apply the new manual fill option overlay (A6066901) to the new manual
fill option bezel (B3615401-C). With a 3/8” wrench, remove the four kep
nuts that hold the controller to the original bezel and install it onto the
new bezel using the original hardware.
15.Reconnect the controller plug and mount the bezel using the original
hardware. Install the fill knob and tighten the set screw. Make sure the
knob only travels within the markings of the overlay.
16.If a water source is available, hook it up and inspect all connection points
for leaks. If a water source is not available fill the tank with water and
inspect all connection points below the water line.
L80-045 Rev0 (11/07)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE LEFT INTENTIONALLY BLANK
L80-045 Rev0 (11/07)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
In the event of problems with or questions
about your order, please contact the Pitco
Frialator factory at (800)258-3708 US and
Canada only
In the event of problems with or questions
about your equipment, please contact the
Pitco Frialator Authorized Service and
Parts representative (ASAP) covering your
area, or contact Pitco at the numbers listed
to the left.
(603)225-6684 World Wide
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501
SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301
L80-045 Rev0 (11/07)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|