AKB-1 Battery Pack
Operational manual for use with Photogenic AC/DC
StudioMax II & III & PerforMax monolights.
This DC power supply is primarily designed for use with
AC/DC monolights from Photogenic Professional Lighting.
AKC320B & AK320B
320 watt second model.
AKC160B & AK160B
160 watt second model.
AK4001MLB
150 watt second model.
Photogenic Professional Lighting
1268 Humbracht Circle
Bartlett, Illinois 60103-1631
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of the battery.
The battery may not be installed in the unit when it arrives. To install
the battery, remove the protective padded case around the unit. There
is a Velcro strip between the padded case and the unit housing.
Separate the Velcro strips and the housing can be removed. At the
opposite end from the display panel, there is a sliding door that must be
opened exposing a channel compartment for the battery. The battery
must be placed into the channel with the silver contacts toward the
opened door. Push the battery into the channel until you feel resistance
and the door can be closed. Place the housing back into the soft case
for protection.
Download from Www.Somanuals.com. All Manuals Search And Download.
Control Panel Layout.
Charging the battery.
The battery pack becomes the charger when you connect the AC/DC wall
adapter included in the package.
Before using the battery for the first time, it must be charged
for a minimum of three hours.
Charging Procedures.
1. Turn the main On/Off switch to the ON position.
2. Plug the adapter into the battery and then into the wall.
3. Turn the Flash/Charge switch to CHARGE.
a. The red charge indicator light will turn on indicating the
charging circuit is working.
b. The green charging light will turn on indicating energy is
being replaced in the battery cells. You may notice the pack
becomes warm during this process, this is normal.
4. When the pack is fully charged, the green charging light will begin to
blink (instead of remaining constant) which indicates the charging
cycle is complete.
5. Disconnect the charging adapter and move the flash/charge switch
to FLASH.
There are three green and one red battery power indication lamps on
the control panel. When you turn the battery switch on after a full
charge, all three green LED lamps should be illuminated. As you use the
stored battery power fewer green lights will be lit until you have drained
the battery at which time the red indicator lamp will come on and the
battery should then be recharged.
Download from Www.Somanuals.com. All Manuals Search And Download.
Your new fully charged power pack will provide between 100 to 200 full
charge flashes depending on the model you have. This is an
approximation for full power flashes and dialing down power can
increase the number of charges you will have for your light. Carry a
backup battery when you are in the field for extended periods of time, or
do not have access to power.
Note: When you are using the light in battery mode, the
modeling circuit is disabled to prevent incidental draining of
battery power. Using the lights in AC mode, the modeling circuits are
fully functional.
Connecting to your Light.
1. Make sure both the battery and the light are switched to the
OFF position.
2. Connect the battery-to-light cable to the light and then to
the battery.
3. Move the flash/charge switch on the battery to FLASH.
4. Move the power switch on the light from OFF to Flash. (If
your flash unit has a modeling light, be sure it is off, or the
battery will not charge the flash.)
5. After the light switch is moved to flash, turn the battery
power switch to ON. Your battery is now charging the light
unit. The ready light on the back of the light will indicate
when it has been charged to the selected power level. The
ready light on the battery will begin to blink as an indication
that the light has been charged. This LED will continue to
blink until the light is discharged. It is recommended that
you turn the battery to off to conserve energy if the light is
not in use.
Maintaining your battery.
It is a good practice to periodically recharge your battery to
maintain the pack in the best condition. We recommend every
two weeks even if you do not plan to use the pack within this
interval.
Give your battery pack a rest after 15 to 30 minutes of use. The
pack will generate heat during the recharge cycles and this rest
will allow the pack to cool and lengthen its useful life.
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not leave the unit in a hot humid environment or in direct
sunlight for extended periods.
Use only charger/adapters with the specified limits.
Do not drop the unit.
Do not use in the water, submerged, mist or rain water.
Do not attempt to disassemble or repair the unit.
Do not touch the flash socket or the end of the cable of the
monolight. Always plug the cable into the light first and then
plug the cable into the battery pack.
Specifications.
Charge Input
Requirement
Charger Input
Socket
DC18V, 600mA
Round Coaxial type with center –ve and perimeter +ve
Output
Voltage/Current
Approx. DC305V/500mA when a battery as specified is
used
DC12V, 2.3Ah (at room temperature) lead-acid type
dimensions and designs as indicated at Basic features.
Battery to be Used
Accompanying
Accessory
Cord for connection to studio flash
8.8 in./220 mm (L) x 4.4 in./110mm (W) x 1.88 in./47mm
(H)
Approx. 3 pounds Net
Physical Dimensions
Weight
Download from Www.Somanuals.com. All Manuals Search And Download.
|