Perle10/100/1000 Ethernet
Extended Temperature
Media Converters
Installation Guide
S-1110-XT
P/N 5500321-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The default DIP switch settings (all switches in the UP position)
will work for most installations.
These are the steps required to configure the Perle S-1110-XT
Ethernet media converter:
1. Insert SFP Module (SFP Model only).
2. Set the Auto-MDIX jumper setting (optional).
3. Set the DIP switch settings (if required).
4. Set the Powering Option Jumpers (if required).
5. Install and connect the fiber cable(s).
6. Install and connect the copper cable(s).
7. Power up the media converter.
Auto-MDIX Jumper Settings
Note: The factory settings for Auto-MDIX will work for most
installations, but in the rare case that you need to modify the
settings, the procedure is below.
To access the Auto-MDIX jumper settings, unscrew the six side
screws on the case and remove the cover plate. Locate the MDIX
AUTO jumper set as detailed below. By covering or strapping pins
1 and 2, the S-1110-XT will operate as an MDIX device. By
covering or strapping pins 2 and 3, the S-1110XT will
automatically detect the Ethernet cable’s polarity. Removing the
strapping is the same as AUTO.
Note: The default jumper setting is AUTO
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP Switches
The DIP switches are accessible through the opening in the side
of the enclosure.
Note: All switch changes take effect immediately.
DIP Switch Settings
Auto Negotiation copper (Switch 1)
Switch Position Copper
Up (default)
Down
Auto
Off
Note: Auto negotiation should only be turned off, if the copper link
partner does not support Auto Negotiation and fixed settings are
required by the copper link partner.
4
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Auto: When enabled, the media converter will negotiate with its
link partner to determine the most optimal parameters for this
connection. The S-1110-XT will advertise capabilities of 10,100
and 1000 Mbps, full and half duplex as well as pause, and remote
fault capabilities to the link partner.
If the copper link partner does not support Auto negotiation, the
S-1110-XT will parallel detect to 10 or 100 Mbps and force Half
Duplex mode as per IEEE specifications.
Off: When the Auto Negotiation switch is set to the OFF position,
the media converter will not negotiate the Ethernet parameters
with the copper link partner. The parameters used by the media
converter will be determined by the Duplex (switch 4) and Speed
(switch 5) DIP switch settings.
.
Link Mode (Switch 2)
Switch Position Mode
Up (default)
Down
Standard Mode
Smart Link Pass-Through
Standard Mode: In this mode, link on the fiber and copper sides
can be brought up and down independently of each other. A loss
of link on either the fiber or copper port can occur without affecting
the other connection.
Smart Link Pass-Through In this mode, the link state on one
connection is directly reflected through the media converter to the
other connection. If link is lost on one of the connections, then the
other link will be brought down by the media converter.
If the installation has a media converter on both ends of the fiber
link and both are set-up for Smart Link Pass-Through, then a loss
of copper link on the far end device will propagate through both
media converters and will result in a loss of link at the near end
device.
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Fiber Fault Alert (Switch 3)
Switch Position Fiber Port
Up (default)
Down
Enabled
Disabled
Enabled: If the media converter detects a loss of signal on the
fiber receiver, it will immediately disable its fiber transmitter signal
on the same port. This, in effect, notifies the fiber link partner that
an error condition exists on the fiber connection.
If the remote media converter is set up for Fiber Fault Alert (FFA)
and the local media converter is set up with Link Pass-Through, a
loss of fiber link will be passed through to the local copper
connection thus notifying the connected device.
If the media converter has been set to Smart Link Pass-Through
mode, the effect will be the same as FFA, since the link loss on
the fiber receiver will result in bringing down the copper link, which
will in turn cause the transmit fiber link to be brought down.
Note: This feature only takes effect if Fiber Negotiation has been
turned off.
Disabled: The media converter will not monitor for or generate
Fiber Fault Alert.
6
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustration of the FFA
The following diagram is an illustration of the operation of this
feature.
(A) – Remote Media Converter setup for Fiber Fault Alert Enabled,
Fiber Negotiation – OFF and Link Mode – Standard.
(B) – Local Media Converter setup for Fiber Fault Alert Enabled,
Smart Link Pass-Through On and Fiber Negotiation - OFF
1 – (A) Loses fiber connection on its receiver.
2 – (A) Sends FFA.
3 – (B) Detects FFA signal and shuts down the fiber link.
4 – (B) Drops link on copper connection because Smart Link
Pass-Through is configured.
5 – (A) Link on copper connection is not affected because Smart
Link Mode is set to Standard.
Duplex copper (Switch 4)
Switch Position Copper port
Up (default)
Down
Full Duplex
Half Duplex
Note: When Auto Negotiation (SW1) is set to Off, the media
converter will use this Duplex setting for the copper port.
Full Duplex: In the Up switch position; the media converter will be
set to Full Duplex mode.
Half Duplex: The media converter will be set to Half Duplex
mode.
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed copper (Switch 5)
Switch Position Copper port
Up (default)
Down
100
10
Note When Auto Negotiation (SW1) is set to Off, the media
converter will use this switch setting for the copper port speed.
100: When Switch 5 is in the Up position, the S-1110-XT will force
the speed to 100 Mbps.
10: When Switch 5 is in the Down position the media converter will
force the speed to 10 Mbps.
Auto Fiber Negotiation (Switch 6)
Switch
Fiber
Position
1000 Mbps
Up (default)
Down
Auto
Off
Auto: The Media Converter will negotiate Ethernet parameters on
the fiber connection. This will ensure that the most optimal
connection parameters will be in effect. If connecting to another
Perle Media Converter, this parameter should be set to Auto. The
Media Converter Module will advertise 1000Mbps, Full and Half
Duplex, no Pause.
Off: The Media Converter Module’s fiber will be fixed to
1000Mbps, Full Duplex.
When using a 100 Mbps SFP module
Full/Half Duplex on Fiber (Switch 6)
Switch
Fiber
Position
100 Mbps
Up (default)
Down
Full Duplex
Half Duplex
Full Duplex: The Media Converter Module will be set to Full
Duplex mode on its fiber link.
8
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Half Duplex: The Media Converter Module will be set to Half
Duplex mode on its fiber link.
Loopback Fiber-1 (Switch 7)
Switch Position Mode
Up (default)
Down
Disabled
Enabled
Disabled: The loopback feature is disabled. This is default
position for normal operation. The switch must be set to this
position in order for data to pass through the media converter.
Enabled: This is a test mode. All data received on the receive
(RX) fiber connection is looped back to the transmit (TX) fiber
connection. The data link will be disabled; however power to the
powered devices will be maintained. This mode will override all
other switch settings.
Installing the SFP Fiber Module
SFP models only.
1. Locate the appropriate fiber module and insert the SFP into
the opening on the front of the media converter.
2. Ensure the SFP module is properly seated. The release latch
of the SPF fiber transceiver must be in the closed (up) position
before insertion.
3. The SFP module may be inserted before or after applying
power to the media converter.
4. Proceed with cable connections.
Installing the Duplex Fiber Cable
1. Locate a 1000Base-X compliant duplex (2 strands) fiber cable
with appropriate connectors.
2. Connect the fiber cables from one media converter to the
other media converter/switch/fiber device ensuring that the RX
and TX are reversed (crossed) at the opposite end.
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Simplex Fiber Cable
1. Locate a 1000Base-X compliant simplex (1 strand) fiber cable
with appropriate connectors. Ensure that the TX wavelength
matches the RX wavelength at the other end and the RX
wavelength matches the TX wavelength at the other end.
2. Connect the fiber cable from one media converter to the other
media converter/switch/fiber device.
Installing the Copper Cable
1. Locate 10/100/1000Base-T compliant copper cables with the
appropriate connectors.
2. Connect the RJ-45 cable between the Perle media converter
and the device.
Note: The Perle media converter supports Auto-MDIX which
allows connection of a straight-through or cross-over Ethernet
cable. See Auto-MDIX Jumper Settings in this guide for jumper
positions.
Grounding the Media Converter
If your installation requires additional grounding this procedure can
be followed.
Grounding the chassis requires the following items:
•
•
•
One grounding lug (not provided).
Grounding wire 12 to 18 AWG (not provided).
Cross-head screwdriver (not provided).
Note: For your safety, when installing this equipment, always
ensure that the chassis ground connection is installed first and
disconnected last.
10
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Attach the grounding lug to the ground wire.
2. Attach the lug to the chassis with the grounding screw(s).
Powering up the Perle Media
Converter
Extended Temperature models are supplied with a
Pluggable Terminal Block
•
•
•
•
Unplug the terminal block from the Media Converter.
Ensure the Power Source is off.
Strip both wires 5mm (3/16th inch)
Loosen the terminal block screws and connect Positive (+)
wire to the left terminal. Connect the Negative (-) wire to
the right terminal. Tighten Terminal screws (0.22Nm-
0.25Nm torque).
•
•
•
•
Plug the terminal block into the Media Converter
Turn on power source.
Check that the PWR LED light is lit.
For extra power cable strain relief, attach the strain clip to
the case as shown below, and thread the power cable
through the clip in either one or two loops.
Perle 10/100/1000 Ethernet Extended Temperature Media Converter 11
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Status LED
The Perle 10/100/1000 Rate converting Extended Temperature
Media converters have status LEDs located on the front panel of
the unit.
PWR
On – Power is applied to the unit
Blinking (slow) – Loopback mode (one or both fiber interfaces are in
loopback mode)
Blinking (fast) Power On failure. See LED Pattern to determine pattern
combination and failure cause
LED Pattern
FDF LKF
FDC PSE
Off
Off
On
On
SFP incompatible
Internal hardware
failure
All other LED patterns
FDF- (Fiber Duplex)
On – Full Duplex
Off – Half Duplex
LKF- (Status on Fiber Link)
On – Fiber link is present
Off – No fiber link present
Blinking (slow) – Fiber link appears functional – Fiber link has been
brought down by Smart Link Pass-Through
Blinking (fast) – Fiber link up and receiving data
12
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
SPD- (Copper Port)
Green – 1000 Mbps
Orange – 100 Mbps
Off – 10 Mbps (if link is currently established)
FDC- (Duplex on Copper)
On – Full Duplex Mode
Off – Half Duplex Mode
LKC- (Link Status on Copper port)
On – Copper link is present
Off – No copper link present
Blinking (slow) – Copper link appears functional – Copper link has
been brought down by Smart Link Pass-Through.
Blinking (fast) – Copper link up and receiving data
Troubleshooting
General
1.
Ensure power source is connected.
2.
Ensure the remote device’s fiber connection type is
compatible with the media converter. If using a simplex
fiber connection, ensure that you have both an Upstream
(U) and Downstream (D) media converter.
3.
4.
Ensure all cabling is of the correct type and is in good
working order.
For duplex fiber connections, ensure the RX and TX has
been reversed between the two media converters.
No connectivity
If unable to get full connectivity with all DIP switches in the UP
position, this procedure is recommended for troubleshooting.
Perle 10/100/1000 Ethernet Extended Temperature Media Converter 13
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Method 1
1. Set the Link Mode to Standard on both media converters.
Leave all other switches in the Up position.
2. Connect the copper device to the copper port on the media
converter. The LKC LED light indicates good copper
connection. If the LKC LED is not lit, check the copper cable
and the attached device.
3. Repeat for the far end media converter.
4. Connect the fiber cable to both media converters. The LKF
LED indicates good fiber connection. If no LKF LED, check the
fiber cabling. Ensure the transmitter and receiver pairs are
crossed.
5. Return the units to the desired configuration. Connect the
power source to the Media converter.
Method 2:
The fiber connection can also be verified by configuring the remote
media converter for loopback mode. The LKF LEDs on both media
converters should be lit. Data should pass through the local
converter, over the fiber connection to the remote media
converter. At the remote media converter, the data will be looped
back and passed through the fiber, back to the local converter and
passed to the copper link.
Technical Specifications
Power Input / Consumption: 6-16V DC / 2.6 W at 12VDC
Operating Temperature:
Storage Temperature:
Operating Humidity:
Storage Humidity:
Operating Altitude:
Dimensions:
-40°C to 75°C (-40°F to 167°F)
-40°C to 85°C (-40°F to 185°F)
5% to 90% non-condensing
5% to 95% non-condensing
Up to 3,048 m (10,000 ft)
150 mm by 95 mm by 26 mm
489,616hours
MTBF SC/ST Models:
MTBF SFP Models:
584,216hours
14
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Fiber Optic Specifications:
Wavelength
(nm)
TX Power
(dB)
RX Power
(dB)
Model
Mode
MM
SM
Budget
7.5
S-1110-M2xx05-XT
TX: 850
RX: 850t.
Min: -9.5
Max: -4
Min: -17
Max: -3
S-1110-S2xx10-XT
S-1110-S1SC10U-XT
S-1110-S1SC10D-XT
S-1110-SFP-XT
TX: 1310
RX: 1310.
Min: -9.5
Max: -3
Min: -20
Max: -3
10.5
11
TX: 1310
RX: 1490
Min: -9
Max: -3
Min: -20
Max: -3
SM
TX: 1490
RX: 1310
Min: -9
Max: 3
Min: -20
Max: -3
SM
11
SFP
Note 1
Note 1: Fiber characteristics will depend on the SFP fiber module
selected.
It is recommended the SFP fiber modules used with this product
are rated for ambient temperature -40°C to 85°C (-4 0°F to 185°F)
Fiber Cabling Requirements:
MM:
50/125 microns or 62.5/125 microns
SM:
9/125 microns
Ethernet Copper Cabling Requirements:
•
•
•
Category 5 UTP or STP
24-22 AWG
Straight through or Ethernet crossover
Note: Please refer the product page on the Perle website for the
most up to date models and specifications:
Perle 10/100/1000 Ethernet Extended Temperature Media Converter 15
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Compliance Information
FCC
This product has been found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions in this Guide, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
his/her own expense.
EN 55022, Class A
WARNING This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take adequate
measures.
EN 55024, Class A
Laser Safety – IEC 60825-1:2007
This product meets Class I Laser safety requirements per IEC-60825-1:2007
standard and complies with FDA/CDRH 21 CFR1040.10 and 21CFR1040.11.
WARNING: Visible and invisible laser radiation may be present when cables are
not connected. Do not stare into the beam or view the beam directly with optical
instruments. Failure to observe this warning could result in an eye injury or
blindness.
WARNING: Use of controls, adjustments or the performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Warranty / Registration
Perle’s standard Lifetime Warranty provides customers with return
to factory repairs for Perle products that fail under the conditions of
the warranty coverage. Details can be found at:
Contacting Technical Support
Perle Technical Assistance Center (PTAC) at the link:
Copyright
© 2012 Perle Systems Limited
All rights reserved. No part of this document may be reproduced or used in any form
without written permission from Perle Systems.
16
Perle 10/100/1000 Ethernet Extended Temperature Media Converter
Installation Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|