Pelco Home Security System C3422M B User Manual

I N S T A L L A T I O N

Pressurized

Spectra^®IV Series

Pendant Back Box

with Fiber Optic Option

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Loosen the V-band attached to the back box and let it hang to the side.

Figure 3. Loosening the V-band

4. Prepare the lower dome for installation:

a. Remove the O-ring from the lower dome.

b. Lightly apply O-ring lubricant (supplied) to the O-ring.

c. Reinstall the O-ring in the groove on the trim ring.

NOTES:

•

Repeated assembly of the unit, without exercising extreme caution to protect the integrity of the O-ring and sealing

surfaces, will result in increased refilling cycles. Plan carefully to minimize service accesses.

•

Use the supplied O-ring lubricant to ensure an airtight seal when installing the lower dome.

Figure 4. Applying O-Ring Lubricant

5. Attach the back box leash to the lower dome, and let the lower dome hang to the other side of the back box.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 5. Attaching the Back Box Leash

6. Install the dome drive. Refer to Table A for a list of compatible dome drives and back boxes.

a. Set the DIP switches located on the base of the dome drive. Refer to the labels located on the base of the dome

drive or to Switch Settings on page 12.

b. Line up the blue and red tabs with the blue and red arrows on the hinged door inside the backbox.

c. Push in the tabs. Insert one side and then the other side. Continue pushing until both sides of the dome drive

click into place.

Figure 6. Installing the Dome Drive

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Spectra Dome Drive and Back Box Compatibility

Back Box

Dome Drive

Spectra II Spectra III Spectra IV

Spectra II^®

•

™

Spectra III

•

Spectra IV

7. Install the lower dome:

a. Position the lower dome so that the blower duct inside the back box is between the studs attached to the inside

of the lower dome.

b. Install the V-band around the lower dome and then tighten the fastener of the V-band.

c. Test the operation of the unit before pressurizing the dome.

Figure 7. Installing the Lower Dome

8. Pressurize the inside of the dome with nitrogen:

a. Remove the cap from the Schrader valve of the dome. Place the air chuck from the charging kit over the

Schrader valve.

NOTE: You may use your own charging equipment or Pelco’s EH8000RKIT recharge kit. If you are using your own

equipment, adjust the regulator for an output pressure of 12 psi (83 kPa).

b. Open the tank valve of the charging kit. Fill the dome with nitrogen for a minimum of five minutes to replace the

oxygen inside the dome with nitrogen.

c. Remove the air chuck and then replace the Schrader valve cap.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

d. Refer to the Operation/Programming manual (C3412M) for instructions on how to view the current readings for

temperature and pressure. Record the initial temperature and pressure readings of the dome in the space

provided below:

Initial Temperature _______________

Initial Pressure _________________

NOTES:

•

Record the initial temperature and pressure readings for future reference. It is normal for changes in temperature to

cause dome pressure to rise and fall.

•

You must perform an annual refill to be consistent with the intent of the application.

Figure 8. Pressurizing the Dome

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Site Installation

1. Feed a fiber optic cable (not supplied) and the supplied wiring harness into the front of the mount and out the back of

the mount. Connect the wires as required. Refer to Table B, Table C, and Table D on page 10, and Table E on page 11

for cable and wiring information. Fasten the mount to the mounting surface (refer to the instructions supplied with

the mount).

Figure 9. Wiring the Mount

2. Remove the back box mounting plate: Loosen the nuts on top of the back box until they reach the locking material at

the end of the studs, and then turn the mounting plate clockwise and lift.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 10. Removing the Back Box Mounting Plate

3. Thread the wiring from the mount through the mounting plate, and then attach the mounting plate to the mount.

If outdoors, apply thread compound (supplied) to the threads on the mounting plate.

Figure 11. Attaching the Mounting Plate

4. Attach the wire harness connector to the mating connector located on the top of the back box. Connect the fiber optic

cable. Insert the studs and nuts on top of the back box into the mounting plate, turn the back box counterclockwise,

and then tighten the three nuts.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 12. Attaching the Wire Harness Connector

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. Fiber Optic Cable Types

Spectra Model

Cable Type

9/125 μm cable

62.5/125 μm cable

Connector

ST type

Single mode (PRS models)

Multimode (PRM models)

ST type

Table C. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC applications and are calculated with a 10-percent

voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered devices.)

Wire Gauge

Total VA

20 AWG

18 AWG

16 AWG

1.5 mm²)

14 AWG

(0.5 mm²)

(1.0 mm²)

(2.5 mm²)

39 ft

(12 m)

62 ft

(19 m)

98 ft

(30 m)

156 ft

(48 m)

NOTES:

•

Input power for the dome is 24 VAC only. Power consumption is 73 VA per dome.

Use a 24 VAC transformer with a minimum of 100 VA.

Table D. UTP Wiring Distances

Receiver

Maximum Distance

Active

(video only)

0 to 3,000 ft

(0 to 914.4 m)

Passive

0 to 750 ft

(0 to 228.6 m)

(video, Coaxitron^®, and

Pelco V-Sync)

NOTE: As a minimum, UTP requires Cat5, 100-ohm twisted pair cable.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Configuration of Wire Harness

Wire Color Function

9-Conductor Cable

Black

Red

Alarm 1

Alarm 2

Alarm 3

Alarm 4

Alarm 5

Alarm 6

Alarm 7

Ground

White

Green

Brown

Orange

Yellow

Violet

Blue

–

Not Used

5-Conductor Cable

Black

Red

Relay N.O. (Aux. 1)

Relay N.C. (Aux. 1)

Relay Common (Aux. 1)

Ground

Green

Brown

White

Auxilary 2

Cat5 Cable

Green

White/Green

Blue

TX+

TX-

RX+

White/Blue

Orange

RX-

UTP Video (+)

UTP Video (-)

Spare

White/Orange

Brown

White/Brown

Spare

Coaxial Cable

Coaxial Core

Video Out

Coaxial Shield

Video Shield

Individual Wires

White

Black

24 VAC (AC HI)

24 VAC (AC LO)

Earth Ground

Green/Yellow

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Switch Settings

WARNING: If you are using Pelco D or Pelco P protocol control, your system may not operate if the baud rate and

address switches are not set correctly. The switches are set at the factory at the defaults for Pelco D protocol

control (2400 baud and address 1).

Table F. Switch Settings for SW2

Special Systems

Switch Number

AD-32 Preset System

CM9502 Setting

Vicon

Not currently available; SW2-3 is reserved for future use.

Serial Port Settings

Switch Number

RS422

OFF OFF

OFF ON

ON ON

RS485, 4-Wire

RS485, 2-Wire

Pelco D and Pelco P Protocol Baud Rate

Switch Number

2400 Baud (Default for Pelco D Protocol Control)

4800 Baud (Default for Pelco P Protocol Control)

9600 Baud

OFF OFF OFF

ON OFF OFF

OFF ON OFF

Video Cable Type

Switch Number

Coax Cable

OFF

UTP Cable

Dome Termination

Switch Number

OFF

Terminated

Not Terminated

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table G. Switch Settings for SW1, Pelco P Protocol Control

NOTE: For Coaxitron controls, SW1 is not used; set all switches to the OFF position. For Pelco D protocol control systems, refer to

Table H on page 13.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1

SW1-2

SW1-3

SW1-4

SW1-5

SW1-1

SW1-2

SW1-3

SW1-4

SW1-5

OFF

Table H. Switch Settings for SW1, Pelco D Protocol Control

NOTE: For Coaxitron controls, SW1 is not used; set all switches to the OFFposition. For Pelco P protocol control systems, refer to

Table G on page 13.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

100

101

102

103

104

105

106

107

108

109

110

OFF

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

OFF

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

OFF

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

OFF

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

GENERAL

Construction

Back Box

Dome Drive

Lower Dome Trim Ring

Bubble

316L stainless steel

Aluminum, thermoplastic

316L stainless steel

Polycarbonate, 0.09-inch thick

316L stainless steel

Brass

V-Band

Pressure Relief

Schrader Valve

Connector

Brass

Nickel-plated steel

Light Attenuation

Smoked

Clear

f/1.0 light loss

Zero light loss

Pressurization

Valve

Pressure

Schrader

8 psig (not factory pressurized)

10 psig

Pressure Relief

Pan Movement

Vertical Tilt

360° continuous pan rotation

+2° to -92°

Manual Pan/Tilt Speeds*

Pan

Tilt

0.1° to 80°/sec manual operation, 150°/sec turbo

0.1° to 40°/sec manual operation

Preset Speeds

Pan

Tilt

400°/sec

200°/sec

Operating Temperature

Maximum

Minimum

(Assumes no wind chill factor)

140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum

-60°F (-51.1°C) absolute minimum; minimal icing at sustained minimum of -50°F

(-45°C); prevents icing at sustained minimum of -40°F (-40°C); de-ices 0.1 inch

(2.5 mm) within 3 hours after power-up

Weight (approximate)

Back Box

Dome Drive

10.2 lb (4.60 kg)

3.3 lb (1.48 kg)

Lower Dome

ELECTRICAL (Dome Drive Only)

Input Voltage

18-32 VAC; 24 VAC nominal

22-27 VDC; 24 VDC nominal

*For variable-speed operation, an appropriate controller is required. With fixed-speed controllers, pan/tilt speed is

20°/sec. The CM6700/CM6800 controller with the KBD200A keyboard has programmable fixed speeds.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

Input Power

24 VAC

73 VA nominal (with heater)

24 VDC

3 A nominal (with heater)

Fuse

1.25 A

Auxiliary Outputs

Alarm Inputs

10.6 (26.7)

11.6

(29.5)

5.9 (15.1)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

C3422M-B (3/08)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective

in material or workmanship for a period of one year after the date of

shipment.

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence,

infringement of any rights of any party or product liability, relating to the

Products shall not exceed the price paid by the Dealer to Pelco for such

Products. In no event will Pelco be liable for any special, incidental, or

consequential damages (including loss of use, loss of profit, and claims of third

parties) however caused, whether by the negligence of Pelco or otherwise.

Exceptions to this warranty are as noted below:

•

Five years on fiber optic products and TW3000 Series unshielded twisted

pair (UTP) transmission products.

•

Three years on Spectra^®IV products.

Three years on Genex^®Series products (multiplexers, server, and

keyboard).

The above warranty provides the Dealer with specific legal rights. The Dealer

may also have additional rights, which are subject to variation from state to

state.

•

Three years on DX Series digital video recorders, DVR5100 Series digital

video recorders, DigitalSENTRY^®Series hardware products, DVX Series

digital video recorders, NVR300 Series network video recorders, and

Endura^®Series distributed network-based video products.

warranty repair is required, the Dealer must contact Pelco at

(800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number

(RA), and provide the following information:

•

Three years on Camclosure^®and Pelco-branded fixed camera models,

except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X,

MC3651H-2, and MC3651H-2X camera models, which have a five-year

warranty.

1. Model and serial number

2. Date of shipment, P.O. number, sales order number, or Pelco invoice number

3. Details of the defect or problem

•

Three years on PMCL200/300/400 Series LCD monitors.

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and

DF5/DF8 Series fixed dome products.

Two years on Spectra III^™, Spectra Mini, Esprit^®, ExSite^®, and PS20

scanners, including when used in continuous motion applications.

Two years on Esprit and WW5700 Series window wiper (excluding wiper

blades).

Two years (except lamp and color wheel) on Digital Light Processing (DLP^®)

displays. The lamp and color wheel will be covered for a period of 90 days.

The air filter is not covered under warranty.

Two years on Intelli-M^®eIDC controllers.

If there is a dispute regarding the warranty of a product that does not fall

under the warranty conditions stated above, please include

explanation with the product when returned.

written

Method of return shipment shall be the same or equal to the method by which

the item was received by Pelco.

•

RETURNS

To expedite parts returned for repair or credit, please call Pelco at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA

number if returned for credit, and RA number if returned for repair) and

designated return location.

•

All merchandise returned for credit may be subject to a 20 percent restocking

and refurbishing charge.

One year (except video heads) on video cassette recorders (VCRs). Video

heads will be covered for a period of six months.

•

Six months on all pan and tilts, scanners, or preset lenses used in

continuous motion applications (preset scan, tour, and auto scan modes).

Goods returned for repair or credit should be clearly identified with the

assigned CA or RA number and freight should be prepaid.

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to a Pelco designated location. Repairs made necessary by reason of misuse,

alteration, normal wear, or accident are not covered under this warranty.

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union

regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.

REVISION HISTORY

Manual #

C3422M

Date

9/06

Comments

Original version.

C3422M-A

C3422M-B

11/06

3/08

Inserted Spectra III compatibility note. Added serial port settings to Table F.

Added information to Preinstallation section regarding the use of O-ring lubricant to create an airtight seal.

Pelco, the Pelco logo, Camclosure, DigitalSENTRY, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.

Spectra III is a trademark of Pelco, Inc.

DLP is a registered trademark of Texas Instruments Incorporated.

Vicon is a trademark of Vicon Industries, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

Australia Finland France Germany Italy Macau The Netherlands Russia Singapore

South Africa Spain Sweden United Arab Emirates United Kingdom United States

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Stereo Amplifier ICS 4200 User Manual
Pentax Digital Camera ZX M User Manual
Philips Cassette Player D 8184 User Manual
Philips Digital Photo Frame 9FF2CME 37 User Manual
Philips MP3 Docking Station 26PFL3321S User Manual
Philips Stereo System FW V330 User Manual
Pioneer Stereo Receiver 516 S K User Manual
Polk Audio DVD Player DR 3 User Manual
Polk Audio Home Theater System ES2 Series User Manual
Precor Treadmill M94 User Manual