Remote Operation Panel
AK-HRP931P
Before attempting to connect, operate or adjust this product, please read these
instructions completely.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Overview ......................................................................................................................................................................... 3
Accessories ..................................................................................................................................................................... 3
Operating precautions ..................................................................................................................................................... 4
Parts and their functions ................................................................................................................................................. 5
ROP operation panel ....................................................................................................................................................................... 5
ROP connector panel .................................................................................................................................................................... 16
Connections .................................................................................................................................................................. 16
System component connections .................................................................................................................................................... 16
Reference files .............................................................................................................................................................. 16
Calling reference files .................................................................................................................................................................... 16
Storing reference files .................................................................................................................................................................... 16
External dimension drawings ........................................................................................................................................ 17
Specifications ................................................................................................................................................................ 17
Overview
≥ This remote operation panel (ROP) is used to control a multi-format camera (AK-HC931P) and a camera control unit (CCU). An
optical fiber cable is used to connect the multi-format camera and CCU, and a dedicated multi-cable (optional accessory) is used
to connect the ROP and CCU.
≥ When the designated multi-cable is used to connect the ROP and CCU, the distance between these two components can be
extended to a maximum of 50 meters.
Accessories
Mounting screws (M4, 8 mm) .......................................... a2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating precautions
≥ The panel’s power is supplied from the camera control unit (AK-HCU931P).
≥ Handle the panel carefully.
Dropping the panel or subjecting it to strong impact may cause malfunctioning and failures.
≥ Operate the panel within a temperature range of 32 °F to 104 °F (0 °C to 40 °C).
Operation in locations below 32 °F or above 104 °F may adversely affect the internal parts.
≥ Turn off the power before connecting or disconnecting the cables.
≥ Do not use the ROP outdoors.
≥ Maintenance
Disconnect the multi-cable, and wipe the panels with a dry cloth. To remove stubborn dirt, soak a cloth in some diluted kitchen
detergent and wring it out well, and then wipe the panels gently.
<Caution>
≥ Avoid using benzine, paint thinners and other volatile substances.
≥ If a chemically treated cleaning cloth is to be used, read the precautions for its use carefully.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
3
Camera power switch indicator
This indicates whether the camera power is ON or OFF.
Lights up green:The panel is communicating with the
camera.
Lights up red: The panel is not communicating with the
camera.
ROP operation panel
When any of the panel switches is pressed, the buzzer sounds.
However, the buzzer does not sound when the panel's ON
switch lamp is off or when BUZZ OFF has been selected on the
FUNC menu.
Flashes red:
POWER OFF status established by
software.
:
2
1
3
4
8 5 9
6
4
5
VF power OFF switch [VF OFF]
This is the camera VF power switch for exercising remote
control from the panel. It lights when the switch is in the ON
position. Each time the switch is pressed, the status
alternates between ON (power ON) and OFF (power OFF).
CAMERA NO.
ALARM
ROP ON HEAD ON VFPW
SD CARD
AUTOSET UP
WHITE BLACK
SD card slot
CLOSE
5600K
BAR
TEST
BLK
CHARACTER
OPT
FAN
;
<
RST
7
CABLE
60Hz
This is where the SD cards are inserted. The data of the
camera and CCU can be saved on these cards and then
called.
MODE
FLARE
OFF GAMMA ON OFF
GAMMA
KNEE
OFF
WHITE MATRIX HD. DTL SD. DTL
CLIP OFF ON OFF OFF
6
7
Camera number indicator [CAMERA NO.]
This indicates the camera number information. If the camera
number is not indicated, “–” appears instead.
=
1
ROP ON switch
This switch enables the controls on the ROP’s operation
panel to be operated. Its lamp lights as soon as the CCU
power is turned on.
Camera video output selector switch
[CLOSE/BAR/ TEST]
This is used to select the camera video signals which are to
be output from the CCU’s rear panel. The camera video
signal, color bar display signal or test display signal is
selected by pressing the BAR switch and/or TEST switch.
Both BAR and TEST switch lamps off:
Lighted: The lamp of the switch lights when the CCU power
is turned on. When communication with the
camera is enabled, the settings at which the
panel's switches are selected are established. The
panel is set on the basis of the camera setting
information also immediately after the ROP ON
switch is pressed and its lamp is lighted. However,
if it is judged that communication with the camera
has been cut off, the setting at which the panel’s
switches are selected will not be established, and
the ROP ON switch lamp will remain lighted.
Camera video output
BAR switch lamp lighted: Color bar signal output
TEST switch lamp lighted: Test signal output
CLOSE switch lamp lighted: Lens closed status with
camera video output
8
AUTOSET UP
Off:
The lamp turns off and the panel’s operations are
cancelled (protected status) when this switch is
pressed (while its lamp is lighted) while the CCU’s
power and the camera’s power is ON.
WHITE BLACK
However, even when the ROP ON switch lamp is
off, the panel’s GAIN, FLARE and DTL controls
can be operated provided that the active indicator
is lighted. It is also possible to operate the iris
close switch irrespective of the ROP ON switch
setting provided that communication with the
camera is enabled.
1
2
3
1Auto white balance switch [AUTO WHITE]
This is used to automatically adjust the white balance.
Lighted: This indicates that the automatic white balance
adjustment has started.
Flashing:This indicates that the automatic white balance
adjustment ended without being completed.
Off:
This indicates that the automatic white balance
adjustment was completed correctly.
2
Camera power switch [HEAD ON]
This switch enables the panel to be used to operate the
camera’s power by remote control. However, this function
will not work unless both the CCU’s camera power switch
and the power switch on the camera itself are at the ON
position.
Each time the switch is pressed, the status alternates
between ON (power ON: LED lighted) and OFF (power OFF:
LED off).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
2Auto black balance switch [AUTO BLACK]
This is used to automatically adjust the black balance.
Lighted: This indicates that the automatic black balance
adjustment has started.
Flashing: This indicates that the automatic black balance
adjustment ended without being completed.
1Optical transmission alarm indicator [OPT ALARM]
This is the optical transmission warning indicator.
Lighted: The indicator lights when the optical signals
received in the transmission between the camera
and CCU are too weak or when a CCU optical
transmission receiver unit data error has
occurred.
Off:
This indicates that the automatic black balance
adjustment was completed correctly.
If the optical signals received in the transmission
between the camera and CCU are too weak, an
alarm display appears in character form. Check
the optical connector connections and mating.
If the problem persists, turn off the CCU power,
disconnect the cable between the camera and
CCU, and clean the optical contact area. Use
cotton swabs moistened with alcohol to wipe the
optical fiber part gently.
3Auto setup switch [AUTO SET UP]
This is used to perform auto setup. The setup status is
output to PM each time.
The mode settings are performed using AUTO SETUP
MODE on the FUNC menu.
OUTSIDE FULL: Standard setup based on the external
shooting chart is performed.
OUTSIDE EASY: Simplified setup based on the external
shooting chart is performed.
In either OUTSIDE mode, align the position of the 4:3 gray
scale (GS-3) wedge with the position of the 4:3 marker.
Depending on the chart setting conditions, auto setup may
not go smoothly. For this reason, attention must be paid
to how the chart is set.
Off:
This indicates that the signals received in the
optical transmission are strong enough.
2Cable alarm indicator [CABLE ALARM]
This is the camera cable warning indicator.
Lighted: This indicates that the camera and CCU are not
connected.
Auto setup methods
Lighted: This indicates that the auto setup has started.
Flashing at 1 sec intervals:
If the indicator is lighted all the time, turn off the
CCU power, inspect and check the cables and
connectors. If it still fails to light, consult your
dealer.
This indicates that the auto setup ended without
being completed.
Flashing at 2 sec intervals:
Off:
This indicates that the camera cable has been
connected correctly.
When the AUTO SET UP switch is pressed
while the indicator is off, the auto setup start
preparation mode is established, and a square
marker appears in the center of the camera's
viewfinder. Roughly align this square with the
white at the gray scale center. Auto setup now
starts when the side switch is pressed. If the
switch is pressed for 1 or more seconds, auto
setup is canceled.
3Fan alarm indicator [FAN ALARM]
This indicates that the CCU’s fan has stopped or that the
camera’s fan is OFF.
Lighted: The CCU’s fan has stopped or the camera’s fan
is OFF.
Off:
Both the CCU’s fan and the camera’s fan are
operating normally.
Off:
This indicates that the auto setup was
completed correctly.
<
Vertical frequency status indicator [60Hz]
This indicates the vertical frequency status of the camera
system. It remains off when the system’s operating
frequency is 59.94 Hz, but it lights when it is set to 60 Hz.
<Note>
During the auto setup operation, the operation status is
displayed using characters on the PM.
<Note>
60Hz operation is not supported at the present time.
9
:
PM character display switch [CHARACTER]
This is used to set the characters to be displayed on the PM
to ON or OFF.
=
MODE ON/OFF switches
These are used to set the camera operation modes. The
switches with the lighted lamps are the ones which have
been set.
CPU reset switch [RST]
This is used to reset the panel’s CPU. Normally, refrain from
touching it.
MODE
FLARE
BLK
GAMMA
KNEE
OFF
WHITE MATRIX HD. DTL SD. DTL
5600K
OFF GAMMA ON OFF
CLIP OFF
ON
OFF
OFF
;
3
1
1
2
3
4
5
6
7
8
9
:
ALARM
OPT
FAN
CABLE
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
CONTROL
15600K switch [5600K MODE]
SHADING
R
WHITE
CLIP
BLK
GAMMA
BLACK WHITE
G
B
KNEE
UNDO
FUNC
This is used to change the amplification rate of the GBR
signals by an electrical circuit to achieve a white balance
that corresponds to the color temperature of 5600K.
When it is pressed, the B video signal is attenuated by
approximately -6 dB, the R video signal is boosted by
approximately 3 dB, and the G video signal is not
attenuated. Select this switch setting for shooting under a
5600K light source or shooting outdoors.
?
@
>
PED
FLAME GAMMA
GAIN
HD. DTL SD. DTL MATRIX SYSTEM
When the lamp of the switch is off, the white balance is
made to correspond to a color temperature of 3200K.
A
2Flare OFF switch [FLARE OFF MODE]
This is used to cancel the flare correction function (which
suppresses the rise of the pedestal in proportion to the
light quantity). Its lamp lights when the function is
canceled.
>
?
Adjustment item up and down shift switches [3, 4]
These are used to scroll the control item display indicated by
one of the control item selector switches ? up or down.
Control item selector switches
3Black gamma ON switch [BL-K GAMMA ON MODE]
This is used to enable the black gamma function (which
changes the video signal amplification rate in parts where
the light quantity is low). Its lamp lights when the function
is enabled.
When these switches are selected (when their lamps are
lighted), the corresponding adjustment items and adjustment
values appear on the LCD display. The adjustment values
can be changed by one of the 16 adjustment rotary
encoders.
4Gamma OFF switch [GAMMA OFF MODE]
1
2
3
4
5
6
7
This is used to cancel the gamma correction function
(which provides the signal level of the video signals with
the reverse characteristics matching the TV video signal
input and light-emitting level characteristics). Its lamp
lights when the function is canceled.
SHADING
R
WHITE
CLIP
BLK
BLACK WHITE
G
B
KNEE
GAMMA
UNDO
PED
FLAME GAMMA
GAIN
HD. DTL SD. DTL MATRIX SYSTEM
FUNC
5This switch is not supported at the present time.
8
9
;
<
=
>
?
@
:
6Knee OFF switch [KNEE OFF MODE]
1Black shading control switch
This is used to cancel the knee function that attenuates
those parts of the video signals where a particular level
(knee point) has been exceeded so that they will not
become saturated as easily. Its lamp lights when the
function is canceled.
[BLACK SHADING CONTROL]
This is used to correct the black shading (the coloring of
black images.) When it is pressed and its lamp is lighted
and when one of the SHADING R, B or B switches is then
pressed and selected, the adjustment items for the black
shading appear on the LCD display. The black shading
correction can be adjusted using four of the 16 adjustment
rotary encoders.
7White clip OFF switch [WHITE CLIP OFF MODE]
This is used to cancel the white clip function by which the
video signal output is clipped (saturated). Its lamp lights
when the function is canceled.
HSAW HPAR VSAW VPAR
–100 –49 0
+7
8Matrix ON switch [MATRIX ON MODE]
This is used to enable the matrix function by which the
chroma saturation is compensated for the G (green), B
(blue), R (red), Ye (yellow), Cy (cyan) and Mg (magenta)
signals and by which the chroma saturation and hue are
compensated for the I (skin tone) signals. Its lamp lights
when the function is enabled.
HSAW: Horizontal sawtooth wave correction
This is used to correct the coloring of black screen images
in the horizontal direction in the range of -100 to 100.
When the numerical setting is incremented, the video level
at the left of the screen is increased.
HPAR: Horizontal parabola correction
9HDTV detail OFF switch [HD.DTL OFF MODE]
This is used to cancel the detail enhancer function that
enhances (adjusts the relative hardness/softness) of the
picture quality in the detailed parts of the HDTV video
output. Its lamp lights when the function is canceled.
This is used to correct the coloring of black screen images
in the horizontal direction in the range of -100 to 100.
When the numerical setting is incremented, the video level
at the left and right of the screen is increased.
VSAW: Vertical sawtooth wave correction
:SDTV detail OFF switch [SD.DTL OFF MODE]
This is used to correct the coloring of black screen images
in the vertical direction in the range of -100 to 100. When
the numerical setting is incremented, the video level at the
This is used to cancel the detail enhancer function that
enhances (adjusts the relative hardness/softness) of the
picture quality in the detailed parts of the SDTV video
output. Its lamp lights when the function is canceled.
top of the screen is increased.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
VPAR: Vertical parabola correction
MPNT
This adjusts the master knee point in the range of 110% to
80%.
This is used to correct the coloring of black screen images
in the vertical direction in the range of –100 to 100. When
the numerical setting is incremented, the video level at the
top and bottom of the screen is increased.
RPNT, BPNT
These adjust the R and B knee points in the range of
+20% to –20%.
2White shading control switch
[WHITE SHADING CONTROL]
MSLP
This is used to correct the white shading. When it is
pressed and its lamp is lighted and when one of the
SHADING R, B or B switches is pressed and selected, the
adjustment items for the white shading appear on the LCD
display. The white shading correction can be adjusted
using four of the 16 adjustment rotary encoders.
This adjusts the master knee slope in the range of 0 to
199.
RSLP, BSLP
These adjust the R and B knee slopes in the range of +31
to –31.
HSAW HPAR VSAW VPAR
5White clip control switch [WHITE CLIP CONTROL]
This is selected to change the white clip level. When it is
selected, its lamp lights.
–100 –49 0
+7
HSAW: Horizontal sawtooth wave correction
This is used to correct the coloring of white screen images
in the horizontal direction in the range of –100 to 100.
When the numerical setting is incremented, the video level
at the left of the screen is increased.
CLIP
108%
CLIP: This adjusts the white clip in the range of 80% to
109%.
HPAR: Horizontal parabola correction
This is used to correct the coloring of white screen images
in the horizontal direction in the range of -100 to 100.
When the numerical setting is incremented, the video level
at the left and right of the screen is increased.
6Black gamma control switch [BKL GAMMA CONTROL]
This is selected to adjust the black gamma curve. When it
is selected, its lamp lights.
VSAW: Vertical sawtooth wave correction
BLKR BLKM BLKB
This is used to correct the coloring of white screen images
in the vertical direction in the range of -100 to 100. When
the numerical setting is incremented, the video level at the
top of the screen is increased.
–32 0
+7
BLKR, BLKM, BLKB GAM
These adjust the black gamma curve (R, MASTER or B) in
the range of –32 (black compression) to +32 (black
expansion.
VPAR: Vertical parabola correction
This is used to correct the coloring of white screen images
in the vertical direction in the range of –100 to 100. When
the numerical setting is incremented, the video level at the
top and bottom of the screen is increased.
7Undo switch [UNDO]
When the control data displayed using the control item
selector switches has been changed, this switch is used to
cancel changed data and return to the data first shown on
the screen.
3R, G, B shading switches [R, G, B]
These are used to select the video signals targeted for
black and white shading correction from among the R, G
and B signals. The lamp of the selected switch lights.
8Pedestal control switch [PED CONTROL]
This is selected to adjust the R,G and B pedestal levels.
When it is selected, its lamp lights.
4Knee control switch [KNEE CONTROL]
This is selected to adjust the knee slope and knee point.
When it is selected, its lamp lights.
RPED GPED BPED
The menu is two-tiered: the adjustment items for the knee
point are displayed on the first tier, and the adjustment
items for the knee slope appear on the second tier. With
auto knee, only the knee point can be adjusted.
–100 0
0
GPED, RPED, BPED: G, R, B pedestal level
These indicate the increases or decreases in the pedestal
levels in the range of –800 to +800 as referenced to the
pedestal position where the black balance was attained.
After the black balance is adjusted, 0 is set as the
adjustment value.
RPNT MPNT BPNT
–1% 95% +1%
RSLP MSLP BSLP
–32 31 +1
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
9Flare control switch [FLARE CONTROL]
This is selected to change the amount of flare correction.
When it is selected, its lamp lights.
<HDTV detail control switch [HD.DTL]
This switch is selected to change the amount by which the
picture quality in the detailed parts of the HDTV video
output has been enhanced (by which the relative
hardness/softness has been adjusted). When it is
selected, its lamp lights.
RFLR GFLR BFLR
10 49
0
VDTL HDTL CRSP PEAK
RFLR, GFLR, BFLR
These adjust the R, G or B flare in the range of –100 to
0
0
0
4
LDP DARK
10% 2
+100, and at 0 the flare correction operation is turned off.
:Gamma curve control switch [GAMMA CONTROL]
This is selected to adjust the gamma correction. When it
is selected, its lamp lights.
Since the M GAM adjustment value is independent of the
R and B GAM adjustment values, the R and B GAM
values remain unchanged even when M GAM is changed.
CORNER SRC +CLP –CLP
20
+KNE –KNE
G
0
0
0
0
KDTL CRSP FREQ
0
0
3
RGAM GGAM BGAM
–50 0.450 +7
+CLP –CLP +KNE –KNE
0
0
3
M GAM: Master gamma
Adjustment range: 0.600 to 0.300
SKIN_DTL SKIN_LVL
ON LOW
RGAM, BGAM: R, B gamma
Adjustment range: –75 to +75
ZEB PHAS WIDTH CRSP
ON 123 15
2
RGAM and BGAM adjust the gamma correction as
referenced to the M GAM setting. The control range
extends from GAMMA 0.600 to 0.300 and this value is
displayed as the adjustment value –75 to +75. When
turned clockwise, GAMMA 0.300 (adjustment value +75) is
approached.
VDTL: Vertical detail level
This is used to adjust the amount of vertical detail.
HDTL: Horizontal detail level
This is used to adjust the amount of horizontal detail.
;Gain control switch [GAIN CONTROL]
This is selected to adjust the white balance. When it is
selected, its lamp lights.
CRSP: Crisp
This is used to set the maximum amplitude of the very
faint noise components which are removed from the detail
components.
RGAN GGAN BGAN
–100 +49 0
PEAK: Peak frequency
This is used to select the contour correction frequency
band (boost frequency or peak frequency).
G GAIN
This sets the amount by which the G gain setting is to be
increased or decreased from its reference in the range of
–800 to +800.
LDP: Level depend
This function removes the detail in the dark parts by
means of a coefficient dependent upon the video signal
level so that the dark parts will not appear unnatural.
R GAIN, B GAIN
These set the amount by which the R or B gain is to be
increased or decreased as referenced to their amounts at
the pedestal position where the white balance was
attained in the range of –800 to +800. After the white
balance is adjusted, 0 is set as the adjustment value.
DARK: Dark detail
This function boosts the detail in the dark parts.
CORNER: Corner detail
This function boosts the detail around the edges of the
screen.
SRC: Detail source
This is used to select the source signals for creating the
detail components.
+CLP: Detail edge overshoot clip
This is used to limit the length of the overshoot parts of the
detail edge components.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
–CLP: Detail edge undershoot clip
CRSP: Skin tone detail crisp
This is used to limit the length of the undershoot parts of
This is used to remove the very faint noise components
the detail edge components.
below the level set from the skin tone detail components.
+KNE: Detail edge overshoot knee
This function applies the knee to the detail edge overshoot
parts.
=SDTV detail control switches [SD.DTL CONTROL]
This switch is selected to change the amount by which the
picture quality in the detailed parts of the SDTV video
output has been enhanced (by which the relative
hardness/softness has been adjusted). When it is
selected, its lamp lights.
–KNE: Detail edge undershoot knee
This function applies the knee to the detail edge
undershoot parts.
VDTL HDTL CRSP
KDTL: Knee detail
This is used to boost detail components of the parts where
0
0
0
PEAK1 PEAK2
the knee has been applied.
1
2
CRSP: Knee detail crisp
This is used to remove the very faint noise components
below the level set from the knee detail components.
LDP DARK
10% 2
CORNER SRC +CLP –CLP
FREQ: Knee detail boost frequency
This is used to select the knee detail boost frequency.
3
G
0
0
KNEE CRM CRSP CRED
+CLP: Knee detail edge overshoot clip
This is used to limit the length of the overshoot parts of the
knee detail edge components.
0
0
0
0
SKINDTL SKIN_LVL
ON LOW
–CLP: Knee detail edge undershoot clip
This is used to limit the length of the undershoot parts of
the knee detail edge components.
ZEB PHAS WIDTH CRSP
ON 123 15
2
VDTL: Vertical detail level
This is used to adjust the amount of vertical detail.
+KNE: Knee detail edge overshoot knee
This function applies the knee to the knee detail edge
overshoot parts.
HDTL: Horizontal detail level
This is used to adjust the amount of horizontal detail.
–KNE: Knee detail edge undershoot knee
This function applies the knee to the knee detail edge
undershoot parts.
CRSP: Crisp
This is used to set the maximum amplitude of the very
faint noise components which are to be removed from the
detail components.
SKIN_DTL: Skin tone detail
This is used to set the skin tone detail function to ON or
OFF.
PEAK1: Peak frequency
This is used to select one of the two contour correction
frequency bands.
SKIN_LVL: skin tone detail level
This is used to set the chroma saturation of the parts
where the skin tone detail is applied.
PEAK2: Peak frequency
This is used to select one of the two contour correction
frequency bands.
FZEB: Skin tone area zebra
This is used to set whether or not to apply zebra to the
areas where coring is applied as the skin tones to the Y
signals in the PM output.
LDP: Level depend
This function removes the detail in the dark parts by
means of a coefficient dependent upon the video signal
level so that the dark parts will not appear unnatural.
PHAS: Skin tone area phase
This is used to move the areas recognized as the skin
tones in the range of 153 to 93 along the Q axis on the
color vector display.
DARK: Dark detail
This function boosts the detail in the dark parts.
WIDTH: Skin tone area width
CORNER: Corner detail
This function boosts the detail around the edges of the
screen.
This is used to widen the areas recognized as the skin
tones in the range of 1 to 20 along the I axis on the color
vector display.
SRC: Detail source
This is used to select the source signals for creating the
detail components.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
+CLP: Detail edge overshoot clip
MTX 12, GAIN, PHASE
This is used to limit the length of the overshoot parts of the
detail edge components.
These are used to select the following 12-axis matrix
adjustment items: G, G_Cy, Cy, Cy_B, B, B_Mg, Mg, Mg_R,
R, R_Ye, Ye and Ye_G.
–CLP: Detail edge undershoot clip
This is used to limit the length of the undershoot parts of
GAIN
the detail edge components.
This is used to adjust the chroma saturation (gain) of the
items set using MTX 12 in the range of –127 to +127.
KNEE: Detail edge knee
This function applies the knee to the detail edge parts.
PHASE
This is used to adjust the phase of the items set using
MTX 12 in the range of –127 to +127.
CRM: Chroma detail
This function boosts the detail in the high chroma
saturation.
?SYSTEM
HEADOPTLEVEL
CCU OPTLEVEL
πππππ
πππππ
CRSP: Chroma detail crisp
This is used to remove the very faint noise components
below the level set from the chroma detail components.
RET1 RET2 RET3 RET4
HDSDI1 HDSDI2 HDSDI3 HDSDI4
DCMD UCMD DCLK UCLK
SP SP ON ON
HBAR SBAR PATHO SET
ARIB SMPT OFF 7.5%
CRED: Chroma detail reduce
This is used to suppress the chroma detail edge.
SKIN_DTL: Skin tone detail
This is used to set the skin tone detail function to ON or
OFF.
SDI4
PM
MSEL MLINK
MIX ON
SKIN_LVL: Skin tone detail level
This is used to set the chroma saturation of the parts
where the skin tone detail is applied.
ANLG O_SEL SYNC TYPE
SD RGB ON TRI
H_CO HFIN (HDTV)
99 123
ZEB: Skin tone area zebra
This is used to set whether or not to apply zebra to the
areas where coring is applied as the skin tones to the Y
signals in the PM output.
H_CO HFIN (SDTV)
99 123
PHAS: Skin tone area phase
This is used to move the areas recognized as the skin
tones in the range of 153 to 93 along the Q axis on the
color vector display.
SCCO SCFIN (SDTV)
7
30
SH_H SH_V
0 90H
VER
WIDTH: Skin tone area width
This is used to widen the areas recognized as the skin
tones in the range of 1 to 20 along the I axis on the color
vector display.
CRSP: Skin tone detail crisp
This is used to remove the very faint noise components
below the level set from the skin tone detail components.
HEAD, CCU OPT LEVEL:Camera, CCU light reception
strength level
These indicate the light reception strength margins of the
camera head and CCU.
>Matrix control switch [MATRIX CONTROL]
This is pressed to change the correction amounts for the
R-G, R-B, G-R, G-B, B-R and B-G chroma saturation.
RET1, RET2, RET3, RET4: Return video settings
These are used to set the input allocations of the return
signals.
R-G R-B G-R G-B
DCMD: Down-conversion system selection
This is used to select the down-conversion system.
–10 0
+1 +10
B-R B-G
0
0
UCMD: Up-conversion system selection
This is used to select the up-conversion system.
MTX12
Cy_B
GAIN PHASE
0
0
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
DCLK: Down-conversion link
SCCO (SDTV): Subcarrier phase coarse adjustment
This is used to coarsely adjust the phase of the subcarrier
signal in relation to the SDTV genlock sync signal.
This is used to decide whether to go with the down-
conversion system control based on the AUX external
input or set the down-conversion independently.
SCFIN (SDTV): Subcarrier phase fine adjustment
This is used to finely adjust the phase of the subcarrier
signal in relation to the SDTV genlock sync signal.
UCLK: Up-conversion link
This is used to decide whether to go with the up-
conversion system control that is linked to the down-
conversion system or set the up-conversion
independently.
SH_H: SD/HD horizontal phase
This is used to adjust the horizontal phase of the SDTV
output and HDTV output.
PATHO: Pathological pattern output
This is used to forcibly output the pathological pattern.
SH_V: SD/HD vertical phase
This is used to set the vertical phase of the SDTV output
and HDTV output to line 0 and line 90 (advanced by 90H
for HDTV).
SET: Color bar setup setting
This is used to set the color bar setup.
SD14: HD SD14 output selection
VER: ROP software version
This is used to set the HD SD14 output of the CCU as the
This indicates the software version of this unit.
PM or normal output.
@FUNC control switch
MSEL: Monitor switch selection setting
This is used to set the monitor switch selection to PM,
WFM or the PM-WFM link mode.
ALC SPED WNDW PEAK
0
0
1
4
MLINK: Shading link setting
This is used to set whether to link the monitor when the R,
B or G shading switch has been selected.
POWER SPEED (FAN)
ON LOW
2D-M 2D-E COMB
OFF OFF LOW
AUTOSETUPMODE
OUTSIDEFULL
ANLG: CCU analog output setting
This is used to set the analog output of the CCU to the HD
or SD component.
O_SEL: Output select
This is used to set the analog output of the CCU to RGB
MPED FSEL
or YPbPr.
3% FCTRY
BRIGHT CONT
SYNC: Sync waveform addition setting
This is used to select whether to add the sync waveform to
the analog output.
2
30
DTL CAMNO
ON
BUZZ
SD
1
TYPE: Analog sync phase coarse adjustment
This is used to set the sync waveform to be added to the
HD analog output to binary or tri-level.
BLACK (PAINT)
FLR
EXE
<CARD> MODE
H_CO (HDTV): Horizontal sync signal phase coarse
adjustment
This is used to coarsely adjust the phase in relation to the
HDTV genlock sync signal.
ALC: Auto iris level
This is used to adjust the auto iris level of the lens.
H_FIN (HDTV): Horizontal sync signal phase fine
adjustment
This is used to finely adjust the phase in relation to the
SPED: Auto iris speed
This is used to set the feedback speed of the auto iris.
HDTV genlock sync signal.
WNDW: Auto iris window
This is used to set the image detection area window of the
auto iris.
H_CO (SDTV): Horizontal sync signal phase coarse
adjustment
This is used to coarsely adjust the phase in relation to the
SDTV genlock sync signal.
PEAK: Peak/average setting
This is used to set the ratio between the average and peak
values of the auto iris image detection.
H_FIN (SDTV): Horizontal sync signal phase fine
adjustment
This is used to finely adjust the phase in relation to the
SDTV genlock sync signal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
POWER (FAN): Fan power switch
This is used to set the power of the camera head’s fan to
ON, OFF, or AUTO.
FILTER
HEAD
ND
25
CC
6.3
B
D
CAP
100
6.3
1.6
3.2
R
4.3
G
DFO
ENC
SCENE FILE
MONITOR
STORE
1
5
2
3
4
8
B
SEQ
C
G
6
7
SPEED (FAN): Fan speed
This is used to set the speed of the camera head’s fan.
GAIN
GAIN
G
-6 -3
0
3
6
9
12
R
R
B
E
F
SHUTTER
2D-M: Component 2-dimensional low-pass filter
This is used to set whether to apply the 2-dimensional low-
pass filter to the SDTV component output.
BLACK
G
H
B
ON
VAR
DTL
2D-E: Composite 2-dimensional low-pass filter
This is used to set whether to apply the 2-dimensional low-
pass filter to the SDTV composite output.
FULL AUTO
L
J K
COMB: Comb filter mode
This is used to set the comb filter mode.
B
FILTER
HEAD
ND
25
CC
CAP
100
6.3
1.6
3.2
4.3
6.3
DFO
AUTO SETUP MODE: Auto setup mode setting
This is used to select the auto setup mode setting.
1
2
3
1ND filter switches [ND FILTER 1, 2, 3, 4, 5]
These are the ND filter selector switches. The filter setting
MPED: Auto setup MPED convergence value
This is used to set the position where the master pedestal
can be changed when the HEAD switch lamp is off.
is to be converged when auto setup has been started.
ND1: Cap
ND2: Through (green light emitted)
FSEL: File select
ND3: 1/4
ND4: 1/16
ND5: 1/32
This is used to select the file attribute to be referenced
when auto setup has been started.
BRIGHT: Dot matrix display brightness setting
This is used to set the brightness of the dot matrix display.
2HEAD switch [HEAD FILTER]
This is used to switch the control over the filter to the
camera head. Its lamp lights when filter control by the
camera head is enabled, and it goes off when filter control
by this panel or MSU is enabled.
CONT: LCD display contrast setting
This is used to set the LCD display contrast.
BUZZ: ROP buzzer setting
This is used to set the panel’s buzzer to ON or OFF.
The lamps of the HEAD switches on this panel and MSU
will light also when the LOCAL switch on the operation
panel at the back of the studio camera has been pressed
and its lamp is lighted.
CAMNO: Camera number setting
This is used to set the number of the camera to which this
unit is connected.
3CC filter switches [CC FILTER A, B, C, D, E]
These are the CC filter selector switches. The filter setting
can be changed when the HEAD switch lamp is off.
CCA: 3200K (green light emitted)
CCB: 4300K
DTL (PAINT): DTL control mode
This is used to set the paint control DTL to SD or HD.
BLACK (PAINT): BLACK control mode
This is used to set the paint control BLACK to be used
with the flare, pedestal or gamma.
CCC: 6300K
CCD: Cross
CCE: DF0
<CARD>: SD card read/write setting
This is used to write the camera’s data on the SD card or
read it from the card.
C
SCENE FILE
STORE
1
5
2
3
4
6
7
8
@
LCD display
This shows the adjustment items and adjustment values
when the control item selector switches ? have been
selected.
3
1
2
1Scene file switches [SCENE FILE 1 to 8]
These enable the camera settings for each scene or the
data in the adjustment data that can be transferred to
another camera to be saved in or called from eight files
that serve as scene files.
A
Adjustment rotary encoders
These enable the data of the adjustment items shown on the
LCD display @ to be changed.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
Calling scene file data
E
1
1. From among the 1 to 8 scene file switches, press the
number of the switch that corresponds to the scene file
which is to be called and light its lamp.
GAIN
-6 -3
0
3
6
9
12
2. The scene file is now read. The data read from the scene
file is input into the current file and then output.
3. When the scene file is read, the data left in the current file
until that moment is temporarily saved. The lamp of the
scene file switch remains lighted even after the data has
been called.
2
1Gain selection status display [GAIN display]
This displays the video input sensitivity gain.
–6 dB: The input sensitivity is increased by –6 dB.
–3 dB: The input sensitivity is increased by –3 dB.
0 dB: The input sensitivity is increased by 0 dB (standard
setting).
3 dB: The input sensitivity is increased by 3 dB.
6 dB: The input sensitivity is increased by 6 dB.
9 dB: The input sensitivity is increased by 9 dB.
12 dB: The input sensitivity is increased by 12 dB.
To stop calling the scene file, press the scene file switch
with the lighted lamp and turn its lamp off. The data that
was temporarily saved before the scene file was called is
now returned to the current file as the setting information,
and the setting statuses established prior to the scene file
call are also restored.
If a scene file switch other than the one with the lighted
lamp is pressed and its lamp is lighted, the scene file
corresponding to the number of the scene file switch with
the now lighted lamp is called.
2Gain setting increment, decrement switches (2
These are used to set the gain selection.
,
1
)
2Scene file storage switch [SCENE FILE STORE]
This is pressed to store setting or adjustment data as
scene files.
F
1
2
SHUTTER
Saving the current file as a scene file
1. When the scene file storage switch is pressed, its lamp
lights up.
ON
VAR
4
2. When the switch with the number of the scene file in which
the data is to be saved is pressed and its lamp is lighted,
the saving of the current file starts and, upon completion,
the lamp of the scene file storage switch goes off.
3
1Shutter switch [SHTR ON]
3Scene file selector switch [SCENE 1-4/5-8 SELECT]
This is used to set the electronic shutter mode or V.RES
mode, which has already been set, to ON or OFF. When
it is selected, its lamp lights. The 4-digit LED display
shows the reciprocal of the shutter value (CCD charge
storage time) or the V.RES mode.
D
Monitor selector switches
[R, G, B, SEQ, ENC MONITOR]
These are used to select what is to be displayed on the
waveform monitor (WFM) and picture monitor.
The output mode can be changed by selecting the MSEL
and MLINK settings on the fourth tier of the SYSTEM screen.
If MLINK is set to ON when BLACK SHADING and WHITE
SHADING are to be adjusted, the monitor display is also
switched temporarily in linkage with the R, G and B shading
switches.
2Shutter mode selector switch [VAR]
This is used to select the step electronic shutter mode or
the continuously variable shutter mode. Its lamp lights up
when the continuously variable shutter mode has been
selected.
3Shutter/V.RES display
HDTV
Y/-G
SDTV
Y/-G
In the electronic shutter mode, this indicates the reciprocal
of the shutter value; in the vertical high resolution mode, it
indicates the resolution steps (11 to 19).
Monitor selector
switch
P-M
R
P-M
R
R
G
R
G
R
G
G
G
4Increment, decrement switches [3, 4]
These are used to change the 4-digit LED display data in
the electronic mode or V.RES mode.
If 4 is pressed in the V.RES mode, the data appears
when “100” is shown as the shutter value on the
shutter/V.RES display.
B
B
B
B
B
SEQ
ENC
RGB
RGB
Y
RGB
VBS
Y/-G
VBS
Y
The R, G and B switches can be selected simultaneously.
The RGB outputs on the WFM display are shown as a
parade display.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
G
M
R, G, B gain controls [R, G, B GAIN]
Iris/master pedestal control joystick [IRIS/PED]
The iris level of the lens is adjusted by moving the joystick up
and down, and the master pedestal is adjusted by turning it.
These are used for the red (R), green (G) and blue (B)
adjustments of the white balance. When the auto white
balance can be performed and the R, G or B gain control is
turned, the gain control value on the LCD display changes.
When in the auto iris mode:
The iris can be adjusted manually.
When not in the auto iris mode:
The auto iris level is adjusted.
H
R, G, B black controls [R, G, B FLARE]
Whether these controls are to be used to adjust the flare or
pedestal can be set on the menu. They are used for the red
(R), green (G) and blue (B) black adjustments. When the
auto black balance can be performed and the R, G or B
black control is turned, the flare or pedestal control value on
the LCD display changes.
Since the master pedestal adjustment is independent of the
R, G and B pedestal adjustments, the R, G and B pedestal
adjustment values remain unchanged even when the master
pedestal is changed.
N
Iris active switch [IRIS ACTIVE]
This makes it possible to adjust the iris. When its lamp is off,
the iris cannot be controlled from this panel. If the switch is
set to ON and the iris priority is returned to this panel, the
panel can then exercise iris control.
I
DTL control [DTL]
This is used to increment or decrement (paint) the detail
control settings (H-DTL and V-DTL adjustment values which
are set on this panel’s LCD display).
By setting this panel’s DTL HD and SD switches, the effect of
the DTL control can be applied to the HDTV video output or
SDTV video output.
O
P
Master pedestal active switch [M-PED ACTIVE]
This is used to activate the master pedestal control functions
of the joystick. Its lamp lights when the functions are
activated.
J
Iris joystick control range selector switch [FULL]
This is used to set the control range of the iris joystick to
FULL (when the switch lamp is lighted: from open to close).
When the switch lamp is off, the control range of the SENSE
control T is used for control.
Call switch [CALL]
This is pressed to call the camera. While it is held down, the
lamp of the camera’s call switch lights and the buzzer
sounds. After the switch is released, the buzzer stops.
If the call switch on the camera has been pressed, the lamp
of this switch remains lighted while that switch is held down.
K
Auto iris switch [AUTO]
This is used to activate the auto iris function. Its lamp lights
in the auto iris mode.
When the lamp is off, use the Iris/master pedestal control
joystick M to control the lens iris.
Q
R
Alarm display [ALARM]
This lights when optical transmission is not going
satisfactorily or when a problem has occurred in the camera,
CCU fan or power supply.
Q
P L
Lens extender display [LENS EXT]
This lights when the setting of the lens extender is other than
1a.
PED
IRIS
ACTIVE
ALARM
CALL
IRIS
N
LENS
EXT
M-PEDACTIVE
Lighted: The setting of the lens extender is other than 1a.
O
R
S
X0.8
Off:
This indicates that the lens extender is not being
used or that the extender function is not available.
PED
SENSE
RANGE
M
V
S
T
U
Lens ratio effect [a0.8]
This lights when the cross converter is inserted into the lens.
IRIS
W
Iris sensitivity control [SENSE]
This is used to adjust the iris control range of the joystick.
U T
Iris control range control [RANGE]
This is used to adjust the iris control position (shift the control
range) of the joystick.
L
Tally indicators
The red tally indicator is at the top and the green tally
indicator is at the bottom. They light when the respective
tally signals are input to the INCOM/tally connector on the
CCU.
V
W
Master pedestal level indicator
This indicates the master pedestal level in the range of -99 to
99.
Iris f-number indicator
This indicates the lens f-number.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts and their functions
ROP connector panel
X
Y
Z
CCU connector
The camera control unit (CCU) is connected here.
RCP connector
The remote control panel (RCP) is connected here.
PREVIEW
RCP
CCU
Preview control connector [PREVIEW]
This is the output connector which is used for previewing.
When the joystick is pushed in, the contact information is
output.
Y
X
Z
Connections
Connections of the system components
1. Connect this panel by connecting its CCU connector to the
ROP connector on the rear panel of the CCU using the
dedicated ROP cable (optional accessory).
2. After having connected all the components, set the CCU’s
main power switch to ON, and then set the camera power
switch to ON.
ROP
AK-HCU931P
<Notes>
ROP cable
≥ When the camera is not connected, the functions which can
be controlled using this panel are limited to the CCU control
items.
CCU
≥ Before disconnecting the ROP able, be certain to set CCU’s
camera power switch to OFF.
PREVIEW
RCP
CCU
AK-HRP931P
Reference files
This function stores data in the files containing the user’s basic settings (user files) and calls the data from them. It is also possible
to call data from the file in which the initial camera settings were stored at the factory (factory file).
Calling reference files
1Factory file
Press scene file switch 4 while holding down CALL. The file call is completed when the scene file switch 4 LED goes off.
2User files
Press scene file switch 1, 2 or 3 while holding down CALL. The file call is completed when the scene file switch LED goes off.
Storing reference files
User files
When the camera is adjusted and set to the statuses which are to be stored and the scene file storage switch is pressed, the
LED of the switch flashes red. When scene file switch 1, 2 or 3 is now pressed while holding down CALL, the lamp of the
scene file storage switch lights up. Storage is completed when the lamp goes off.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
External dimension drawings
C C U
R C P
P R E V I E W
CAMERA NO.
ALARM
ROP ON HEAD ON VFPW
SD CARD
AUTOSET
WHITE BLACK
UP
CLOSE
5600K
BAR
TEST
BLK
CHARACTER
OPT
FAN
RST
CABLE
60Hz
MODE
AUTO KNEE
KNEE ON OFF
FLARE
GAMMA
WHITE MATRIX HD. DTL SD. DTL
OFF GAMMA ON OFF
CLIP OFF
ON
OFF
OFF
CONTROL
SHADING
R
WHITE
CLIP
BLK
GAMMA
BLACK WHITE
G
B
KNEE
UNDO
FUNC
PED
FLAME GAMMA
GAIN
HD. DTL SD. DTL MATRIX SYSTEM
FILTER
HEAD
ND
25
CC
4.3
CAP
100
6.3
1.6
1.1
G
6.3
8.0
SCENE FILE
MONITOR
STORE
16-1/2 inch
(419 mm)
1
1
2
2
3
3
4
4
5
5
R
B
SEQ
ENC
GAIN
GAIN
G
-
6
-
3
0
3
6
9
12
R
R
B
SHUTTER
BLACK
G
B
ON
VAR
DTL
FULL AUTO
PED
IRIS
ACTIVE
ALARM
CALL
IRIS
LENS
EXT
M-PEDACTIVE
X0.8
PED
SENSE
IRIS
RANGE
Remote Operation Panel AK-HRP930P
5-3/8 inch
(136 mm)
2-3/16 inch
(55 mm)
Specifications
Power supply:
DC 12 V (DC 10 V to 17 V)
(Supplied from CCU)
Power consumption: 6 W
indicates safety information.
CCU control:
Control signals (camera, CCU control)
Power supply (DC 12 V)
Tally control signals
RCP control:
Control signals (fader control)
Power supply (DC 12 V)
Control signals
PREVIEW control:
Maximum cable extension distance:
Operating temperature range:
Storage temperature range:
Operating ambient humidity:
Dimensions (W k H k D):
50 meters
32 °F to 104 °F (0 °C to + 40 °C)
–4 °F to 140 °F (–20 °C to +60 °C)
Less than 80%
5-3/8 k 16-1/2 k 2-3/16 inch (136 k 419 k 55 mm)
(excluding protrusions)
Weight:
Approx. 5 lbs (2.3 kg)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
PANASONIC BROADCAST & TELEVISION SYSTEMS COMPANY
UNIT COMPANY OF MATSUSHITA ELECTRIC CORPORATION OF AMERICA
Executive Office:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7000
EASTERN ZONE:
One Panasonic Way 4E-7, Secaucus, NJ 07094 (201) 348-7621
Southeast Region:
1225 Northbrook Parkway, Ste 1-160, Suwanee, GA 30024 (770) 338-6835
Central Region:
1707 N Randall Road E1-C-1, Elgin, IL 60123 (847) 468-5200
WESTERN ZONE:
3330 Cahuenga Blvd W., Los Angeles, CA 90068 (323) 436-3500
Government Marketing Department:
52 West Gude Drive, Rockville, MD 20850 (301) 738-3840
Broadcast PARTS INFORMATION & ORDERING:
9:00 a.m. – 5:00 p.m. (EST) (800) 334-4881/24 Hr. Fax (800) 334-4880
Emergency after hour parts orders (800) 334-4881
TECHNICAL SUPPORT:
Emergency 24 Hour Service (800) 222-0741
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010
Panasonic de Mexico S.A. de C.V.
Av angel Urraza Num. 1209 Col. de Valle 03100 Mexico, D.F. (52) 1 951 2127
Panasonic Sales Company
Division of Matsushita Electric of Puerto Rico Inc.
San Gabriel Industrial Park, 65th Infantry Ave., Km. 9.5, Carolina, Puerto Rico 00630 (787) 750-4300
Printed in Japan
VQT0A41
F1002T @
P
Download from Www.Somanuals.com. All Manuals Search And Download.
|