Omron GPS Receiver NS10 V2 User Manual

Read and Understand this Catalog

Please read and understand this catalog before purchasing the product. Please consult your OMRON representative if you have any

questions or comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or

other period if specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,

MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT

THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR

INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED.

NS12-V2 NS10-V2 NS8-V2

12-inch Model

10-inch Model

8-inch Model

NS5-V2 NSH5

5-inch Model

5-inch Hand-held Model

Programmable Terminals

NS-CXDC1-V1

LIMITATIONS OF LIABILITY

Ver. 1

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR

COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT,

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

NS-series Screen Creation Software

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

Installing a Navigator: A Totally New Concept in

Programmable Terminals

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS

UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND

MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of the

product in the customer's application or use of the product.

Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will be

used.

Know and observe all prohibitions of use applicable to this product.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT

THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT IS PROPERLY

RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with your

OMRON representative at any time to confirm actual specifications of purchased product.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a

warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application requirements.

Actual performance is subject to the OMRON Warranty and Limitations of Liability.

Printed on 100%

Recycled Paper

Note: Do not use this document to operate the Unit.

OMRON ELECTRONICS LLC

OMRON Corporation

Authorized Distributor:

1 East Commerce Drive, Schaumburg,

IL 60173 U.S.A.

Control Devices Division H.Q.

Shiokoji Horikawa, Shimogyo-ku,

Tel:(1)847-843-7900/Fax:(1)847-843-8568

Kyoto, 600-8530

Japan

OMRON ASIA PACIFIC PTE. LTD.

83 Clemenceau Avenue,

#11-01, UE Square,

Tel:(81)75-344-7109

Fax:(81)75-344-7149

Singapore 239920

Tel:(65)6835-3011/Fax:(65)6835-2711

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69, NL-2132 JD Hoofddorp

The Netherlands

Tel:(31)2356-81-300/

Fax:(31)2356-81-388

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120 China

Tel:(86)21-5037-2222/Fax:(86)21-5037-2200

NSH5

NS5-V2

5-inch Model

NS8-V2

NS10-V2

10-inch Model

NS12-V2

12-inch Model

5-inch

8-inch Model

Hand-held

Model

Cat. No. V078-E1-09

Printed in Japan

0206-1M

Note: Specifications subject to change without notice.

NS Series

Download from Www.Somanuals.com. All Manuals Search And Download.

We are always trying to

provide solutions that will

give the highest added

value to your system.

We strive to solve on-site

problems with our

Make it More Simple

Seamless

The NS is moving to the next stage, from a touch screen

to an advanced machine management tool.

solutions instead of just

providing touch screen

functions. That is what

OMRON is focused on.

It's convenient

but…

Machine Management

Touch Screen Operation

Switch Operation

Smart

Turning switches into Touch Screens brings

enhancements, such as minimum wiring,

space savings, and improved local operation

efficiency. Moreover, OMRON works to

minimize the customer's energy expenditure

from machine design to troubleshooting.

OK!

It's convenient

but…

Previous PT

Previous zone

New zone

NS Enters a New Zone

From PLC Memory Allocation

to Device Access

NS Series

The NS Series achieves

flexible data access to a

variety of devices. It

enables operators to reach

the devices on the network

including Special I/O Units,

intelligent devices, and

PLCs.

Previous PTs shared data that was

allocated in advance to specific words in

the CPU Unit, and they were used to

assist with device operations, and to

display error locations, and

countermeasures.

Special I/O Units

PLC

CPU Unit

PLC

Network

Example: DeviceNet

It's time for

switch inspection.

Allocated data

Sharing allocated

data with CPU Unit

Intelligent devices

Example: DRT2-series Smart Slave

The cylinder

speed is strange.

Smart Active Parts

(Functional software parts)

Example: Monitoring maintenance information

for various DeviceNet Smart Slave models

Download from Www.Somanuals.com. All Manuals Search And Download.

Don't you have these problems?

PTs as a Machine Navigator

NS-series PTs navigate all areas of machine operation,

from daily operation to error recovery.

The Smart Active Parts are the solution.

Using all of the device-specific

personal computer tools at startup is

Various device-specific tools

okay, but using the personal

computer tools for error recovery

during operation is overly difficult.

Peripheral Devices for PLC

Network control

Temperature settings and

monitoring tools

Personal computer tools

Setting tool for position control

Wouldn't it be simpler to use the PT instead?

With an NS-series PT, just drag and drop Smart Active Parts to customize the interface

for your machine.

NS-series PTs provide Smart Active Parts that allow direct data access

to a variety of devices.

Only with NS!

PLC System Objects

The PT is traditionally a

terminal that exchanges data in

Previously

a CX-Programmer

was required.

Just

attach to

a screen.

allocated areas with the PLC's CPU

Unit. The internal and external control

of a PLC with only this type of data

exchange is, however, difficult.

A NS-series PT, however, uses

communications functions and Smart

Active Parts to incorporate

software computer functions to

operate as a Device Navigator.

Position Control Objects

Ensures easy

screen settings

in the NCF.

NS Series

Example: RS-232C

Colors and

sizes can be

changed.

NS Series

Device operations

Example: Ethernet

NS: Device Navigator

Displaying device error locations

DeviceNet Objects

Devices accessed without a program.

Previously

Example: DeviceNet

a DeviceNet

Personal computer tool

Configurator was

required.

Displaying countermeasures

Internal device monitoring

and resetting

(Supporting recovery methods)

Temperature Controller Parts

ThermoTool was

required in the

With version 2 PTs (V2 suffix in model number), hardware functions are upgraded.

past.

Large Capacity

NS8-V2/NS10-V2/NS12-V2: 60 MB

(-V1: 20 MB, same as before)

NS5-V2: 20 MB

Increased Visibility

NS8-V2: Increased from 8.0 to 8.4 inches

NS5-V2(STN)/NS12: Wider field of vision

Refer to page 15 of this catalog to see the wide variety of Smart

Active Parts.

The Smart Active Parts are accessed by selecting Tools

Use Library from the menu bar of the CX-Designer.

Note: The NS5-V1 has a capacity of 6 MB.

Download from Www.Somanuals.com. All Manuals Search And Download.

Multi-language Terminal

Do you have the following problems when starting

Machine Localization with PTs

the system or when errors occur?

A Multi-language Input Environment

Using Excel

No special PT tools are required for translation

operations.

Translations can be requested using e-mail

attachments.

Label Switching Function for Up to

16 Languages

Devices can be started with Japanese-language

screens, and then operated with screens in other

languages.

When an Error Occurs during Operation

When the System is Started

PT used for operation

after startup.

There is no way for

the PT to recover

following an error.

(Creating a screen

is quite

An error occurs,

and…

The languages can be switch to the one preferred by

the device operators.

troublesome.)

Data exchange is the main function.

English and Japanese

screen data

Japanese-language

screen

English-language

screen

Dual-language

screen data

Either a single screen

Error

data file was divided

between Japanese

and English screens,

or else multiple

screen data files

had to be created.

NS project

Because multiple labels can be

set, screen data needs to be set

only once. Multi-language

capability is simply a matter of

switching labels.

Chinese screen data

Special personal

computer tool

Chinese-language

screen

Use a dedicated computer, and you

have to wade through functionality

that is not being used or that does

not need to be reset.

Recovery can only be performed by a

specialist (i.e., an engineer).

A PT mainly exchanges data with a PLC.

Dedicated PC software is required to

gain access to other devices.

You can get multi-language support in Excel. Switching to as many as 16 languages is as

easy as switching labels.

Dual-language input in Excel by translation

companies and local

companies

Language A screen

data

Language A

Excel data

With the Smart Active Parts

NS project

CSV

Attachment

CSV

The PT can be customized according to the specifications of the device manufacturer to optimize

operation as a tool. This enables equipment maintenance by personnel other than engineers.

Language A and B

Excel data

Dual-language

screen data

Minor maintenance

Customizing and optimizing PT

can be performed on

the PT during operation.

Simply paste one of

the Smart Active

Parts! Then make only

a few device node

settings.

CSV or

Unicode

text

Attachment

CSV

NS project

Smart Active Parts

Note: Windows 2000 or XP is required

for multi-language support.

NS Series

16 languages max.

Label 15

Improved efficiency in creating maintenance screen

Setting specified

Multi-Language PT

Asian Languages

Japanese, Simplified Chinese (see note

1), Korean, and Traditional Chinese

(see note 2)

Label 0

Label 1

parameters and checking status

Only with NS!

European Languages

English, French, German, Italian,

Portuguese, Spanish, Swedish, Dutch,

Finnish, Norwegian,

Smart Active Parts

access data without

any special

Support for 17 languages

Switching to as many as

16 languages by simply

switching the labels

Basque, Catalan, and Danish

programming.

No ladder program

Multi-language conversion has become much easier!

Error Recovery Screen Example

Text and BMP files can be directly specified, so

operations such as correcting contents for recovery and

replacing diagrams and photographs can be executed

without requiring any special tools. For example, if the

recovery operation procedure is changed by system

improvements, screens can be changed by simply

replacing text and BMP files, allowing for rapid

implementation of improvements and countermeasures.

Note: Transfer tools must be used for transfers.

Create a screen like this as

a device troubleshooter.

Creating Chinese, Korean, or Other Language

Screens in Any Language Version of Windows

Multi-language CSV data

When an error occurs, rapid recovery

is critical. With the NS Series, the

following type of screen can be easily

prepared to guide on-site workers to

carry out the operations required for

recovery.

Multi-language Input (When Windows 2000 or XP is Used)

When Windows 2000 or XP is being used, Simplified

Chinese (see note),

Notification that an error

has occurred

Import

Traditional Chinese (see

note), Korean, and other

Display explanations of error

contents and methods for recovery.

(Text file direct specification)

Use diagrams to show error

locations and methods for recovery.

(Bit map file direct specification)

Display only the buttons required for

recovery operations.

language text can be input in

CX-Designer. Select the

Convenient!

desired language with Global

IME to input a different

language.

When importing screen data, the text

attributes of user-specified labels can be

applied to all other imported text. With this

function, entire Japanese text attributes

(e.g., MS Gothic in blue or other colors) can

be used in Chinese labels. Furthermore, by

using the just-fit function, long labels in

English will fit within the frame limits after

automatic font adjustment.

Error contents and

recovery methods are

displayed.

Error location and

Recovery operation screen

is displayed. (Only the

buttons required for

explanations of recovery

methods can be further

displayed by bit maps.

operations are shown.)

Note: Simplified Chinese: Chinese with partially simplified characters, mostly used in

Mainland China.

Note: In addition to the Troubleshooter for the machine above, there is a PLC troubleshooter for CS/CJ-series PLCs. Contact your OMRON representative for information on Troubleshooters.

Traditional Chinese: Chinese with traditional characters, mostly used in Hong

Kong and Taiwan.

Download from Www.Somanuals.com. All Manuals Search And Download.

New functionality added in Ver. 6 extends

the ease of use of the NS-series PTs.

PT System

Ver. 6 or Higher

PT System

Ver. 6 or Higher

Improved Data Logging

Smart Active Parts greatly reduce the number of drawing and programming steps.

Number of logging points greatly increased.

Past logs can be seen.

Tool Functions Provided with Smart Active Parts

For example, the PT can log data at 2-second

intervals 24 hours a day (for a 43,200-point log).

You may want to see logs saved in the past in a

Memory Card on the screen. This is possible with

the NS Series.

Log data in a Memory Card can be read on the screen with the read

file button. A list of files with time stamps will appear on the screen.

By selecting the desired file, the past log in the Memory Card can be

read.

All you need to do is select the required Smart Active

Part in the CX-Designer and drag & drop it on the

screen see page 5).

Smart Active Parts not only reduce the number of

screen drawing and ladder programming steps, but

they also eliminate the need to debug.

Software functions are achieved on the screen

without software such as the CX- Programmer,

CX-Position, and DeviceNet Configurator.

Want to check an error or adjust

settings without any software

tools. But realization of Touch

screen and PLC program are

really time consuming.

Also, it is dangerous to use

software tools since they can do

anything. Isn't it possible to

show or set one only part of the

information?

The number of Always Log points has increased from 1,000 to 50,000

max. per line.

Drastically reduce

your programming

and development

time.

The total number of Always Log points increased from 5,000 to 50,000.

Example:

Logging 1 word and 1 address at 1-second intervals:

50,000 points, with 50,000 logging points per line.

Logging 1 word and 3 addresses at 1-second intervals:

50,000 points, with 16,666 logging points per line.

The log data files in the Memory Card

appear as shown below when the read file

button is pressed.

Make PID settings for temperature

control without connecting software.

As a setting

device for

temperature

control

The number of logging points for one line depends on the number of

logging words and the number of logging addresses. For details, refer to

the manual.

See the error log of the PLC without

connecting software.

Logging continues.

Read file button

As an error

monitor

For example, you may want to log data at

2-second intervals 24 hours a day (a 302,400-point

log). This is possible with the NS Series.

When the logging data reaches the number of preset logging points,

the logging data can be automatically saved in a Memory Card in CSV

format. After automatic saving, the logging data will be cleared.

Therefore, it will be possible to continue logging. (The Memory Card

can hold a maximum of 1,000 files.)

Standard data can be displayed in the data log.

You may want to save the present log data as

standard data in the Memory Card. This is

possible with the NS Series.

By pressing the save to file button, the displayed log data can be

saved in the Memory Card in CSV format. The saved log data can be

overlapped as standard data on the screen by pressing the read file

button. By turning the log start address ON and OFF, logged data can

be controlled to enable/disable logging.

OMRON's

Temperature

Controller

Only three parts are on the screen!

Only one single part is on the screen!

(Direct Connection)

Refer to page 15 of this catalog to see the wide variety of Smart Active Parts.

PT System

Ver. 6 or Higher

Example:

Easy screen transfer from anywhere at higher speed.

Example: Logging 1 word and 1 address at 2-second intervals with

the number of logging points set to

43,200 (i.e., at 2-second intervals for 24 hours a day).

Log start address

Standard data

Data can be transferred over USB through a single

LOG001.CSV 04/06/04 10:00

LOG002.CSV 04/06/05 10:00

LOG003.CSV 04/06/06 10:00

LOG004.CSV 04/06/07 10:00

LOG005.CSV 04/06/08 10:00

LOG006.CSV 04/06/09 10:00

LOG007.CSV 04/06/10 10:00

Memory

Card

It is possible to

make a one-week

log by

automatically

saving the data

seven times.

cable between the computer and PT. No devices for

serial RS-232C and USB conversion are required.

Moreover, USB allows high-speed screen transfer by

just connecting the cable.

Auto-

High-speed screen

transfer through

matically

saved

Most computers now have an

USB port, and no serial

RS-232C ports are provided.

USB.

You may want to transfer

screens more easily at higher

speeds.

Logging data for each

day (43,200 points) is

saved in the Memory

Card in CSV format.

Suffixes are automatically

added to file names set in

the CX-Designer.

Save to file button

Read file button

Note: Lot number 0325 or later is required

for USB screen transfer with NS-V1

models.

Screen transfers

equivalent to

Ethernet.

NS-V2 Hardware Means High Quality, High Performance, and High Capacity

Screen transfers using Memory Cards are possible

from the maintenance menu. No physical switch

operations are required on the rear panel.

Furthermore, easy operation is ensured with no wear

and tear of hardware, including the switch.

Screen transfers

using Memory

Cards are possible

High definition

USB port compatibility with commercially available printers

It is very convenient to make

backups without using a

Displays image data (BMP and JPG) beautifully.

Hard copies of screens can be printed out in color by USB-

computer. It is, however,

NS-V2: 32,000 colors

compatible printers.

USB port included as

standard equipment

troublesome to operate a DIP

switch on the back of the PT

from the

maintenance

NS5

NS8

4,096 colors

32,768 colors

General printer compatible

with USB port

Not

Supported

each time backups are required.

NS5

You may want to make backups

USB cable

Supported

NS8

periodically, but worry because

menu.

Memory

Card

NS10 32,768 colors

NS12 32,768 colors

Supported

the DIP switch pins may break.

NS10

NS12

Manufacturer: EPSON or Canon

Recommended models

Select from

the system menu.

Start downloading/

uploading.

EPSON: PM-2200C, PM-930C, PM-870C,

PM-740C, PM-900C, PM-D600,

EPSON and Canon

printers supported.

Note: NS5-SQ0 (B)-V2: STN models have 4,096 colors.

NS5-TQ0 (B)-V2: TFT models have 32,768 colors.

PM-G720, PM-G730, PX-A650,

PM-G730, PM-D600, PX-A650

Canon: BJ-M70, BJ-M40, PIXUS550i, 50i, 80i,

IP2000, IP3100, IP4100, IP4100R, IP90

The screens can be transferred from a computer in an

office through modems. The maintenance of

the screens is possible without touching the device.

Therefore, no training or engineer visits are required.

Faster drawing speed

Large-capacity image data

Even a single screen change in

a shipped machine involves a

risk, because a screen sent by

High-speed screen switching

Three times the image data capacity for standard models

See note.

Yes

NS5

V 1

V 2

e-mail needs to be transferred

Screen transfer

through modems is

RS-232C

Modem

to a person familiar with

NS8

NS5

NS8

6 MB 20 MB

20 MB 60 MB

operation. Training workers to

Yes

NS8/10/12-V1

20 MB

NS10

NS12

NS8/10/12-V2

60 MB

understand operation is a hard

now possible.

job. Or service personnel need

Yes

200-MHz RISC CPU

High-speed graphics controller

NS10 20 MB 60 MB

NS12 20 MB 60 MB

to visit the site to change

screens.

Note: The NS5

Modem

uses a different

graphic controller

from other models.

Download from Www.Somanuals.com. All Manuals Search And Download.

Powerful Networking

The NS Series is more beautiful and user-friendly.

More beautiful

More user-friendly

Exchanging Data with a PLC over a Network (Multihost)

You can partially replace text and pictures from

your computer.

You can make beautiful screens with simple operations.

Communicating with a PLC via NT Link,

using Ethernet without Special PLC Programming

FTP (File Transfer Protocol) has been

added! Texts, lists, and recipes can be

replaced with the put/get command from

your computer! You can even replace

BMP files from your computer easily.

Using Data Links between the PT and the PLC

Beautiful BMP Parts Collection has

been newly added. Simply select

the desired part, paste it on your

Ethernet Communications without

Programming

Controller Link Interface Unit

The Controller Link is an FA network that can send and

receive large data packets flexibly and easily among

OMRON PLCs and IBM PC/AT or compatible computers. The

NS12 and NS10 PTs can be connected to the Controller Link

network easily via a Controller Link Interface Unit. When a

Controller Link network is used, data can be transferred

between multiple PLCs and NS12/NS10 PTs without writing

ladder programming to manage the communications.

Windows fonts can be used for

NS-series PTs can communicate with a CS/CJ-

series PLC (equipped with an Ethernet Unit)

through “program-free” communications just

like NT Link communications. Data is transferred

through Ethernet through a simple PLC address

and initial communications setup.

screen, and make your screens

switches and lamps Ver.5

Screens, bitmaps, text, recipe data

neat!

Auto font resizing function Ver.5

Automatically resizes fonts to the

object size.No need to adjust font

sizes manually anymore!

Furthermore, just-fit font size

adjustments have been possible

since version 6.

Personal

computer

32,768-color display

The color variation displays

pictures brilliantly!

Ethernet

Direct access

NS-series

More strength in applications

CS/CJ-series

PLC

The following models, which have an RS-485 communications port and

support CompoWay/F communications, can be connected to the NS.

The NS can be connected to a Board PC. The NS can also be directly

Unit

Series and Models

Unit

Series and Models

connected to an OMRON Temperature Controller.

Modular Temperature Controllers

Temperature Controllers

E5AN/EN

Series

E5ZN

E5ZN-SCT24S

(Terminal Unit)

E5AN-

E5EN-

E5AN-

E5EN-

E5CN-

E5GN-

TC Thermocouple input

Temperature-resistance input

TC Thermocouple input

A Memory Link has been added

to the communications method.

It allows the NS to communicate

ControllerLink

Digital Controllers

E5AR

E5ER

E5AR- 03 -FLK

E5ER- 03 -FLK

Temperature-resistance input

Temperature input

Analog input

with a Board PC.

Memory link

CompoWay/F

Temperature input

Analog input

Direct access

TC Thermocouple input

E5CN

Host Link CS/CJ-series,

CVM1/CV-series,

or C-series PLC

Series

Temperature-resistance input

Temperature input

Analog input

The NS can be directly

connected to the OMRON

CS/CJ-series PLC

NS-series PT

NS-series

Temperature Controllers listed

on the right.

TC Thermocouple input

Temperature-resistance input

E5GN

Series

OMRON Temperature

Control Unit

PLC

NS-series

System Configurations

CS/CJ-series

PLC

CS/CJ-series

PLC

Direct access

Various connections, such as 1:1, 1:2, 1:N, and M:N, are supported with Ethernet or serial connections.

PT:PLC = 1:2

PT:PLC = 1:1

SPMA (Single Port Multi Access) Function

Screen data can be transferred through the PLC from the CX-Designer to the PT connected to the PLC in series or via a network.

NS-series PT

You may want to transfer screens to a PT through the PLC without changing

computer connections or to transfer a ladder program to the PLC through the PT

by using the Ethernet or Controller Link.

RS-232C

Communications without

programming

Communications without

programming

Communications without

programming

RS-232C

Ladder programs can be monitored or transferred from the CX-Programmer through the NS-series PT to PLCs connected to the PT

in series or via a network.

(1:1 NT Link, 1:N NT Link,

or Host Link)

To use the SPMA function through the PLC, the following

software and hardware versions are required.

NS-series PT: System version 3.0 or higher

NS Designer: Version 3.0 or higher or

CX-Designer: Version 1.0 or higher

CX-Programmer: Version 3.1 or higher

Screen data or Data in Memory Card

(From CX-Designer through PLC to NS-series PT)

CS/CJ-series PLC

C200HX/HG/HE PLC

SPMA

PT:PLC = M:N

PLC: Lot No. 030201 and later (Refer to the following table.)

PLC

Ladder program

(From CX-Programmer through NS-series PT to PLC)

PLC series

CPU model

CJ1H-CPU65H

CJ1H-CPU66H

CJ1G-CPU42H

CJ1G-CPU43H

CJ1G-CPU44H

CJ1G-CPU45H

CJ1M-CPU11

CJ1M-CPU12

CJ1M-CPU13

CJ1M-CPU21

CJ1M-CPU22

CJ1M-CPU23

CS1H-CPU63H

CS1H-CPU64H

CS1H-CPU65H

CS1H-CPU66H

CS1H-CPU67H

CS1G-CPU42H

CS1G-CPU43H

CS1G-CPU44H

CS1G-CPU45H

CS1D-CPU42S

CS1D-CPU44S

CS1D-CPU65S

CS1D-CPU67S

Lot number

NS-series PT

PT:PLC = 1:N

Computer

RS-232C

PLC

NS-series PT

Ethernet

CJ Series

CS/CJ-

series

PLC

Peripheral

(or RS-232C)

030201

NS-series PT

CS/CJ-series PLC

NS-series PT

Serial

Communications without

programming

Peripheral

bus

(Tool bus)

Ethernet

Computer

(1:N NT Link)

Serial

RS-232C

NT Link

NS-AL002 Converter

(Converts between

RS-232C and RS-422A.)

CS/CJ-series

PLC

CS Series

030201

Controller Link

PLC

CS/CJ-series PLC

Ethernet Unit

Screen transfer

from the

Controller Link

is supported

from version 6.

Host Registration Function

It is possible to register two or more PLCs as hosts and communicate with the PLCs by specifying the host ID and address when connected via Ethernet or

Controller Link.

Serial

NT Link

CS/CJ-series PLC

NS-series PT

Download from Www.Somanuals.com. All Manuals Search And Download.

The NS monitors machine status for who and how machines

are managed to help speed recover from problems.

Monitoring and Setting PLC Data

Using Video Inputs

Easily Displaying the Status of

Particular Bits in Ladder Programs

when Errors Occur

Solve with the Switch Box

function

For Operators

The NS-CA002 has joined the NS-CA001 Video Input Unit.

You may want to input moving images

from a video camera or the image

output from a Vision Sensor, arrange

them on the PT screen, and capture

(save) the images or display the capture

data on the PT.

Saving Displayed Video Images to a Memory

Card in BMP Format

Display machine

status simply.

Switch Box Function

The Switch Box Function has been added to the

NS-series Programmable Terminals. The Switch

Box Function can be used to monitor the status

of each bit in a word or a combination of user-

selected bits organized like a ladder program

section. The Switch Box Function makes it

possible to perform basic troubleshooting on

the factory floor even without a computer.

Image Capture Function

Do not want to be aware of

ladder programs and PLC

memory areas.

Only want to display I/O

comments and I/O status.

When necessary, the displayed image can be captured and

saved in a Memory Card in BMP format. The saved image

can then be uploaded from remote personal computer via

Ethernet or Serial connection.

The number of images that can be saved depends on the

capacity of Memory Card. As an example, about 50 images

from a 640x480 display (about 600 Kbytes each) can be

saved in a 30-Mbyte Memory Card.

Solve with the Device Monitor

function

Monitoring PLC I/O Data for

the Purpose of Device Debugging

and Maintenance

Display PC Screens with the NS-CA002

NS-CA002 RGB/Video Input Unit

(Supported by the NS12-V /NS10-V /NS8-V .)

PT System

Image capture data read function

Ver. 6 or Higher

Display PLC memory

areas without using tools.

An analog RGB input terminal is provided in addition to two

video input interface terminals. A single video or analog

RGB display is possible on the NS-series PT. In that case,

video display is possible in user-defined positions and sizes.

Touch switches and parts, such as lamps, can be

overlapped on the video display. The display of parts will

not disappear.

Device Monitor Function

BMP data captured and saved in a Memory Card can be

read on the PT. BMP data displayed in thumbnails

can be selected and displayed on the captured data display

screen that will appear for the command button.

The Device Monitor Function is a standard feature

in the NS-series Programmable Terminals. Data in

the PLC’s I/O memory can be accessed directly

(read and written.) The Device Monitor provides

functions that can significantly reduce the time

needed to set up the system, such as displaying a

block of consecutive PLC data area addresses and

inputting/verifying parameters in CPU Bus Units

and Special I/O Units.

Want to display and change the

PLC memory areas without

showing the PLC program.

If an error occurs, the image when the error occurred can be displayed

on the NS screen. This is useful for on-site error analysis.

Solve with the Ladder Monitor

function

Monitoring Execution of

the PLC's Ladder Program

Ladder Monitor Function

(NS12-V /NS10-V /NS8-V

)

Display program

The Ladder Monitor Software provided with the

CX-Designer can be used to monitor states,

search for addresses and instructions, and

monitor multiple I/O points at the same time in

CS/CJ-series PLCs ladder programs via a serial,

Controller Link, or Ethernet connection. Copy

the Ladder Monitor software to a Memory Card

and install the Memory Card in the NS-series PT

to enable these monitoring and searching

operations. It is also possible to display I/O

comments created with the CX-Programmer

using an I/O Comment Extract Tool.

without using tools

Want to identify the fault location

by checking the actual PLC

program.

Want to change part of the

program, a timer/counter, without

connecting tools.

RGB

Console

Camera

From CX-Designer version 1.0, the Ladder Monitor software is

stored in the following folder on the CD-ROM. Copy it to a Memory

Card (sold separately) to use it.

Note: Two video signals cannot be simultaneously input to a

For Experts

single screen.

CX-One Disk 3: \Utility\CX-Designer\English\

LadderMonitorFunc.

CX-Designer CD-ROM: \Utility\English\LadderMonitorFunc.

NS-CA001 Video Input Unit

(Supported by the NS12-V /NS10-V /NS8-V .)

Four video input interfaces are provided, so four video or

CCD cameras can be connected. Up to four images can be

displayed simultaneously if the image size is 320x240

pixels.

Facilitate Equipment Maintenance

Integrating Special Unit Functions or Component Peripheral Tool Functions into PTs

Smart Active Parts

The following Smart Active Parts are provided and can be installed on the NS-Designer (version 6 or higher).

For CS/CJ AND CS1D CPU Unit

For Inverters (See note.)

Error Log Monitor, Online Battery Change Button, etc.

For Serial Communications Boards/Units

Communications Status Displays (Error Monitor), Ports Settings, etc.

For Ethernet Units/CLK Units

Rotation Speed/Monitoring Output Frequency, Other Parameter

Settings, etc.

For DeviceNet

DRT2 Maintenance/Status Information, IN/OUT Information, etc.

For Temperature Controllers (E5 R, E5ZN, E5 N and

Network Status Displays (Error Monitor and Network Node Status), etc.

For MC/MCH Unit

JOG Running, Search Zero Position, Program Running, Error Displays,

I/O Status Monitor, PV Monitor, etc.

CJ1W-TC)

Run Monitor, PID Settings SP Settings, Alarm Settings, Input

Correction Settings, etc.

Console

For NC/NCF Unit

For Sensors (E3X-DRT)

JOG Running, Direct Running, Memory Running (NC Only), Error

Displays I/O Status Monitor, PV Monitor, etc.

Threshold Settings, Monitoring Light Reception Levels, Etc.

For the SmartSlice GRT1 Series

Communications Unit Status, Warning/Alarm Flags, Network

Joining/Leaving Status

Wireless Terminals for WT30

Monitoring Slave Operating Status in a Wireless Environment

Camera

For Servo (R88D-WT, R7D-AP) (See note.)

PV Monitor, Parameter Settings, Error Displays, Driver Information

Displays, I/O Status Monitor, etc.

Note: Smart Active Parts require a Serial Communications Units/Boards

(version 1.2 or later).

Download from Www.Somanuals.com. All Manuals Search And Download.

High-reliability and Advanced Functions in

the Industry’s Slimmest PT

Super-thin 48.5-mm Body for a Slimmer Control Panel

Using a Personal Computer to Check PT Operation

This thin-profile model has few protrusions so it can be incorporated easily into a panel or machine.

The PT can help save space when space is at a premium.

Using a Personal Computer to Check the

Test Mode Window

Virtual PLC address

Operation of Created Functional Objects

NS12, NS10

Simulation via the “Test Function”

When a test is started, a test screen and virtual PLC will be

Memory Card interface

displayed on the computer.

Virtual

Test mode

PLC address

CX-Designer

Set values:

300

Present values: 500

500

Operating (clicking with the mouse) the functional objects

on the test screen will change the corresponding address in

the virtual PLC. Conversely, changing the content of a

virtual PLC address will change the corresponding

functional objects. It is also possible to confirm pop-up

screens. This function can be used to confirm the actual

operation of a screen during the editing.

Start of Test

Memory Card

Note: Colors shown in photographs and product

names may differ from actual colors and

names.

9999

Set value:

Created screen

Present values:

Expansion interface

Battery

The test function enables debugging screens without NS

and PLC Hardware.

Transferring Screen Data to the PT On-site from a Memory Card

RS-232C serial port A

RS-232C serial port B

Memory Card: Upload/Download Function

It is possible to download the screen data and system

program to Memory Card and upload the same data from

the Memory Card. It is also possible to automatically

upload the data from the Memory Card to CX-Designer or

automatically download the data from Memory Card to PT

when the power of PT is turned ON.

CX-Designer

Screen data

Automatic transfer

NS-series PT

Screen data

when power of PT

is turned ON.

A bar code reader can be connected

Memory

Card

Power Supply (24 VDC)

USB HOST (for printer)

Ethernet (10Base-T or 100Base-TX)

USB SLAVE (For screen data transfer)

to the serial port.

Recommended bar code reader: V520-RH21-6

Memory Card

NS8

Memory Card interface

NS-series PT

Using General Software

Setting Functional Object Properties in Excel

Using Excel to Analyze Data, Such as the Alarm/Event

History, Operation Log, and Error Log, and to Create

Daily Reports

CSV File Input/Output

Expansion interface

The property settings for each functional object can be

exported in CSV format. The settings data can be imported

again after it has been edited with a program such as Excel.

Memory Card

Note: Colors shown in photographs and product

names may differ from actual colors and

names.

Memory Card: Data Logging Function

Logging data (trend data, up to 50,000 points with a

sampling cycle of 0.5 or 1 to 86,400 s/group) can be stored

in the Memory Card in CSV format.

Editing Text and Bitmap File with Your

Favorite Text Editor

Battery

Logging of

trend data

Editor Specifying Function

The user can select the editor when editing text or bitmap

files.

RS-232C serial port A

RS-232C serial port B

Creating System-related Documents

A bar code reader can be connected

to the serial port.

Power

Supply

(24 VDC)

Memory Card

Recommended bar code reader: V520-RH21-6

Outputting Project Information in RTF

Ethernet

(10Base-T or 100Base-TX)

Data such as screen information and object information can

be output in an RTF file. The RTF file can be read into Word

Processor to produce a system manual.

USB SLAVE (For screen data transfer)

Using Excel to Analyze Time-series Data and

to Create Daily Reports

Example of an RTF File Read into Word Processor

USB HOST (for printer)

Pasted Screen Data as

RTF Data

Object Properties as

RTF Data

Memory Card: History Storage Function

The following data can be saved to the Memory Card in

CSV format.

Alarm/Event History (Alarm/ Event history data)

Operation Log (Screen operation history data)

Error Log (Error log data recorded during macro program

execution)

Built-in Expansion Interface

The NS-series PTs have a built-in Expansion Interface for

future expandability.

USB Ports

A printer can be connected to the USB HOST port.

Refer to Printer Support on page 10 for recommended

printers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Dimensions

NS5

Memory Card interface

NS12/10 PT Units: mm

NS8 PT ^{Units: mm}

177

165 188

140 241

227 249

15.5

180

232

39 (min.)

42 (max.)

48.5

Memory Card

Note: Colors shown in photographs and product names

may differ from actual colors and names.

15.5

264

315

323

7.5

39 (min.)

42 (max.)

48.5

Expansion interface

220

301

Ethernet (10Base-T or 100Base-TX)

USB SLAVE (For screen data transfer)

RS-232C serial port A

Recommended

Panel Cutout Dimensions

Battery

RESET

Recommended

Panel Cutout Dimensions

Power Supply

(24 VDC)

+0.5

165.5

24V

–0

PORT

120.5

107.6

HOST

SLAVE

ETHERNET

RS-232C serial port B

19.1

+0.5

–0

RESET

220.5

A bar code reader can be connected

to the serial port.

Recommended bar code reader: V520-RH21-6

–0

228

121

134

24V

PORT

26.6 9.6

HOST

SLAVE

ETHERNET

44.1 50.1

63.4

–0

302

13.7

49.9

90.4

Optional Products

3.8

RS-422A Adapter

CJ1W-CIF11

Video Input Unit

RGB/Video Input Unit

Controller Link Interface Unit

NS-CLK21 (with Cover)

NS-CA001(with Cover)

NS-CA002 (with cover)

NS5 PT Units: mm

NS5 Hand-held PT Units: mm

39.83

16.5

195

223

70.5

ÇqÇtÇm

153.3

27.3

44.55

142

130.5

176

15.5

145

206.3

34 (min.)

38 (max.)

53.8

54.8

Protective Cover/Anti-reflection

Sheet for NS-series PT

NS -KBA0(N)

RS-232/RS-422A Conversion

Communications Cable

XW2Z-S002

USB Serial Conversion Cable

CS1W-CIF31

Unit

NT30/NT31C-KBA05(N)

NS-AL002

183.5

Recommended

Panel Cutout Dimensions

ÇrÇv

OFF

PORT

+0.5

–0

131

68.48

RESET

ETHERNET

51.7

+0.5

–0

184

19.5

Note: Colors shown in photographs and product names may differ from actual colors and names.

NS-CA001 Video Input Unit

NS-CA002 Video Input Unit

NS-CLK21

Units: mm

Controller Link Interface Unit

Units: mm

81.3

(102.7)

151.5

(183)

9.6

21.4

9.6

21.4

164

(169)

164

(169)

(1.9)

127.3

(22.3)

20.4

9.7

31.5

(22.3)

20.4

9.7

11.1

39.3

57.3

82.8

118.3

164

10.6

(169)

50.3

68.3

86.3

104.3

(1.9)

10.8

(33.9)

95.6

Download from Www.Somanuals.com. All Manuals Search And Download.

Performance/Specifications

General Specifications

NS12/NS10/NS8/NS5-V2

Display Element Specifications

Characteristics

Display Specifications

Communications Specifications

Serial Communications

Item

Specification

Item

NS12-V2

NS10-V2

NS8-V2

NS5-V2/NSH5-V2

Item

Specifications

Item

Specification

Raster font

Displayable characters

Base size

TFT color LCD

STN color LCD

Monochrome LCD

Rated power supply voltage 24 VDC

Alphanumeric characters

or Japanese katakana

1 x 1, 1 x 2, 2 x 1,

2 x 2, 3 x 3, 4 x 4, 8 x 8

Conforms to EIA RS-232C.

D-Sub female 9-pin connector

5-V output (250 mA max.) through pin 6 (See note.)

Display device

High-definition TFT color LCD

Rough

8 x 8

Port A

Allowable voltage range

Power consumption

20.4 to 27.6 VDC (24 VDC ±15%)

Alphanumeric characters

or Japanese, Chinese

(Simplified, Traditional)

or Korean

800 dot horizontal x

600 dot vertical

320 dot horizontal x

240 dot vertical

25 W max. (15 W max. for the NS5)

Number of dots

Display color

640 dot horizontal x 480 dot vertical

256 colors

Font

name

Standard

8 x 16 1 x 1, 1 x 2, 2 x 1,

16 x 16 2 x 2, 3 x 3, 4 x 4, 8 x 8

Conforms to EIA RS-232C.

D-Sub female 9-pin connector

5-V output (250 mA max.) through pin 6 (See note.)

Ambient operating temperature 0 to 50°C (See notes 1 and 4.)

Display

text

Port B

Storage temperature

–20 to 60°C (See note 2.)

Width 246.0 mm x Width 215.2 mm x Width 170.9 mm x

Width 117.2 mm x

height 88.4 mm

(5.7 inches)

TFT: Left/right 70°,

Top 70°, bottom 50°

STN: Left/right 50°,

Top 45°, bottom 50°

Monochrome:

Display

panel

Effective

display area

Alphanumeric characters

or Japanese katakana

Japanese kanji

height 184.5 mm

(12.1 inches)

height 162.4 mm

(10.4 inches)

height 128.2 mm

(8.4 inches)

16 x 32 1 x 1, 1 x 2, 2 x 1,

32 x 32 2 x 2, 3 x 3, 4 x 4, 8 x 8

Fine

35% to 85% (0 to 40°C) with no condensation

35% to 60% (40 to 50°C) with no condensation

Note: The 5-V outputs of serial ports A and B cannot be used at the same time.

Ambient operating humidity

Operating environment

Noise immunity

No corrosive gases.

Vector font

(text objects only)

Can be specified in CX-Designer.

Font, style, and size can be specified.

Controller Link (Wired-type) Specifications

Left/right ±60°,

Left/right ±65°,

Conforms to IEC61000-4-4, 2 kV (power lines)

Field of vision

Service life

Top 45°, bottom 75° Top 35°, bottom 65° Top 50°, bottom 60°

Item

Specification

(See note 1.)

Color

256 colors

Conforms to JIS C0040.

Baud rate

2M/1M/500K

Shielded twisted-pair cable (special cable)

Left/right 45°,

Top 20°, bottom 40°

Vibration resistance

(during operation)

10 to 57 Hz, 0.075 mm amplitude, 57 to 150 Hz,

Font style (only when

vector font is specified)

Transmission path

Bold or italic

9.8 m/s 30 min each in X, Y, and Z directions

Text

attributes

TFT, STN: 75,000

hours min. (See

note 2.)

Monochrome:

50,000 hours min.

(See note 2.)

Shock resistance

(during operation)

Conforms to JIS C0041.

147 m/s 3 times each in direction of X, Y, and Z.

Vertical alignment

Horizontal alignment

Functional

Top, center, or bottom

Ethernet Specifications

50,000 hours min. (See note 2.)

Left-justified, centered, or right-justified

NS12: 2.5 kg max.; NS10: 2.3 kg max.;

NS8: 2.0 kg max.; NS5: 1.0 kg max.

Weight

Item

Specification

Conforms to IEEE 802.3/Ethernet (10Base-T/100Base-T).

Backlight

(See note

5.)

Up to 10 types can be registered.

The flicker speed and flicker range can be set.

Objects

objects

Front operating panel: IP65F and NEMA4 compliant

(See note 3.)

Conformance standards

Enclosure rating

Brightness

adjustment

Backlight error

detection

that can

Flicker

There are 3 levels that can be set with the touch panel. (See note 3.)

Fixed

flicker

Select from 3 types.

objects

The flicker speed and flicker range are fixed.

5 years (at 25°C) Replace battery within 5 days

after the battery runs low (indicator lights orange).

Error is detected automatically, and the RUN

indicator flashes green as notification. (See note 4.)

Battery life

Video Input Specifications

Numeral units and scale settings 1,000 max.

Item

NS-CA001

NS-CA002

Applicable standards

cULus and EC directives

Note 1: The bottom angle is 55° for V1 models.

Alarm/event settings

Display colors

5,000 max.

2: This is the estimated time before brightness is reduced by half at room temperature

and humidity. It is not a guaranteed value. The service life will be drastically shortened

if PT is used at low temperatures. For example, using the PT at temperatures of 0°C

will reduce the service life to approximately 10,000 hours (reference value).

3: The brightness cannot be adjusted much.

4: This function does not indicate that the service life has been reached. It detects when

the backlight is not lit due to a disconnection or other errors. Backlight error detection

indicates that all backlights (2) are OFF.

Resolution

Input signal

320 x 240, 640 x 480, or 800 x 600 dots

NTSC composite video or PAL

User-defined size

Note 1: The operating temperature is subject to the following restrictions according to the mounting

angle.

256 colors max. (32,768 colors for BMP)

NTSC composite

video or PAL

Mounting angle of 0 to 30° to the horizontal: Operating temperature range of 0 to 45°C

When a Video Input Unit or a Controller Link Interface Unit is mounted, the ambient operating

temperature is 0 to 35°C.

CX-One Operating Environment

2 cameras + RGB

Cameras

Number of cameras: 4 max.

Mounting angle of 30 to 90° to the horizontal: See note 4.

Windows 98 SE, Me, NT 4.0 (Service Pack 6a), 2000 (Service

Compatible OS

Note 2: Operate the PT within the temperature and humidity ranges shown in the following diagram.

Pack 3 or higher), or XP (See note 1.)

5: Contact your nearest OMRON representative to replace the backlight.

Humidity (%)

95% 80%

USB Specifications

Pentium II 333 MHz or faster processor (Pentium III 1 GHz or

faster recommended.)

Recommended CPU

Storage

Operating Specifications

Item

Specifications

60%

Operation

Recommended memory 256 Mbytes min. (See note 2.)

90°

Item

Specification

Resistive membrane

USB rating

Connector

USB1.1

Type A (Host), Type B (Slave)

Approx. 1.8 GB or more available space is required to install

Hard disk free space

40%

Method

the complete CX-One package.

Temperature (°C)

35%

20%

NS12-V2

1,900 (50 horizontal x 38 vertical) 16 x 16 dots for each switch.

1,200 (40 horizontal x 30 vertical) 16 x 16 dots for each switch.

768 (32 horizontal x 24 vertical) 20 x 20 dots for each switch.

300 (20 horizontal x 15 vertical) 16 x 16 dots for each switch.

CD-ROM drive

Display

Required for installation

30°

Number

switches

Touch

panel

(Matrix

type)

NS10-V2

SVGA (800 x 600) or better high-resolution display with 256 colors min.

10%

Horizontal

(0°)

NS8-V2

Note 1: CX-One OS precaution

—20

10 20 30 40 50 60 70 80

Temperature (°C)

The CX-One will not run on Microsoft Windows 95 or any other OS not listed above.

If such an OS is being used on the client computer, the OS must be upgraded before installing the

CX-One. System requirements and hard disk space may vary with the system environment.

2: The amount of memory required varies the Support Software applications used in CX-One.

Refer to use documentation for Individual Support Software for details.

NS5-V2/NSH5

Note 3: May not be applicable in locations with long-term exposure to oil.

Note 4: •NS12/NS10/NS5

Compatible OMRON PLCs

Input

Pressure-sensitive

Mounting angle of 30° to 90° or less to the horizontal: Operating temperature range of 0 to 50°C

•NS8

Mounting angle of 30° to less than 90° to the horizontal: Operating temperature range of 0 to 45°C

Mounting angle of 90° to the horizontal: Operating temperature range of 0 to 50°C

Service life

1,000,000 touch operations.

CPU Units (1:1 NT Link Connection)

Model number

CQM1-CPU41-V1/CPU42-V1/CPU43-V1/CPU44-V1

CQM1H-CPU21/CPU51/CPU61

Specifications

PLC model name

C-series CQM1

Data Capacity Specification

Series Display device model

NSH5-SQROOB-V2

With RS-232C connector (9-pin type)

V 1

V 2

C-series CQM1H

C-series CPM1

Item

Specification

MQ (monochrome)

TQ (TFT)

20 MB

60 MB

CPM1-10/20CDR- + CPM1-CIF01

Rated power supply voltage

Allowable voltage range

24 VDC

NS5

Connect to peripheral port.

CPM1A-10/20/30/40CD

CPM2A-30/40/60CD

CPM2C-10/20

+ CPM1-CIF01

C-series CPM1A

C-series CPM2A

C-series CPM2C

C-series C200HS

C-series C200HE (-Z)

C-series C200HG (-Z)

C-series C200HX (-Z)

20.4 to 26.4 VDC (24 VDC –15%/+10%)

10 W max.

SQ (STN)

TV (TFT)

6 MB

Connect to RS-232C or peripheral port.

Power consumption

NSH5

NS8

(See note 1.)

Ambient operating temperature

Storage temperature

0 to 40°C

20 MB

C200HS-CPU21/CPU23/CPU31/CPU33

–20 to 60°C

NS10

NS12

TV (TFT)

C200HE-CPU32(-Z) (See note 2.) /CPU42(-Z)

With RS-232C connector (9-pin type)

Ambient operating humidity

Operating environment

35% to 85% with no condensation

No corrosive gases.

TS (TFT)

C200HG-CPU33(-Z) (See note 2.) /CPU43(-Z) /CPU53(-Z) (See note 2.) /CPU63(-Z)

C200HX-CPU34(-Z) (See note 2.) /CPU44(-Z) /CPU54(-Z) (See note 2.) /CPU64(-Z) /CPU65-Z/CPU85-Z

External Interface Specifications

Common mode: 1,000 Vp-p (between power

supply terminals and panel)

Normal mode: 300 Vp-p

CVM1/CV-series

CVM1 or CV500/

CV1000/CV2000

Item

Specifications

CV500/1000/2000-CPU01-V1

CVM1-CPU01-V2/CPU11-V2/CPU21-V2

Noise immunity

With RS-232C connector (switching/9-pin type)

Memory card

interface

One ATA-Compact Flash interface slot.

Used to transfer and store screen data and to store history data.

Pulse width: 100 ns to 1 µs, Rise time: 1-ns pulse

Note 1: Use an Adapter Cable (CPM2C-CN111 or CS1W-CN114/118), CPM1-CIF01 RS-232C Adapter, or CPM1-CIF11 RS-422A Adapter to connect.

Vibration resistance

(during operation)

Conforms to JIS C0911.

2: A C200HW-COM02(-V1), C200HW-COM04(-V1), C200HW-COM05(-V1), or C200HW-COM06(-V1) Communications Board is required.

Expansion

interface

For Expansion Interface Units

CPU Units (1:N NT Link Connection)

Shock resistance

(during operation)

Conforms to JIS C0912.

Model number

CS1G-CPU42H/CPU43H/CPU44H/CPU45H

CS1H-CPU63H/CPU64H/CPU65H/CPU66H/CPU67H

CS1D-CPU65H/CPU67H

Specifications

PLC model name

CS-series CS1G

CS-series CS1H

CS-series CS1D

CJ-series CJ1G

Weight

1 kg max.

Enclosure rating

Ground

IP65 compliant

Ground to 100 Ω or less.

UL508 and EC directives

Applicable standards

CJ1G-CPU42H/CPU43H/CPU44H/CPU45H (See note 1.)

CJ1G-CPU42P/CPU43P/CPU44P/CPU45P

CJ1H-CPU65H/CPU66H/CPU67H (See note 1.)

CJ-series CJ1H

With RS-232C connector (9-pin type)

CJ1M-CPU11/CPU12/CPU13/CPU21/CPU22/CPU23 (See note 1.)

CJ-series CJ1M

C-series CQM1H

C-series C200HE(-Z)

C-series C200HG(-Z)

C-series C200HX(-Z)

CQM1H-CPU61/51 with a CQM1H-SCB41 Serial Communications Board

C200HE-CPU32(-Z) (See note 2.) /CPU42(-Z)

C200HG-CPU33(-Z) (See note 2.) /CPU43(-Z) /CPU53(-Z) (See note 2.) /CPU63(-Z)

C200HX-CPU34(-Z) (See note 2.) /CPU44(-Z) /CPU54(-Z) (See note 2.) /CPU64(-Z) /CPU65-Z/CPU85-Z

Note 1: The CJ1W-SCU21/SCU41 Serial Communications Unit can also be connected.

2: A C200HW-COM02/COM04/COM05/COM06(-V1) Communications Board is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections through CPU Unit/Host Link

Options

Superior environmental resistance

meets IP65F standards.

Flush surface construction is used for superior

environmental resistance and the enclosure rating for

the front of the PT is IP65F compliant.

IP International Protection

Model number

Specifications

RS-232C or RS-422A adapter connected to peripheral port

RS-232C connector (9-pin)

PLC model name

C Series: CPM1

Model name

Specifications

Model number

NS-CA001

CPM1-10CDR/20CDR- /CPM1A-10CD/20CD/30CD/40CD

CPM2A-30CD/40CD/60CD

Inputs: 4 channels

Signal type: NTSC/PAL

C Series: CPM2A

C Series: CPM2C

Video Input

Unit

Input channels: 2 video

channels and 1 RGB

channel (See note.)

Communications connectors include both a peripheral port and

RS-232C port (branching possible through CPM2C-CN111

Conversion Cable).

Used as separate peripheral and RS-232C ports through CS1W-

CN114/118 Conversion Cable.

NS-CA002

CPM2C-10/20

Signal mode: NTSC/PAL

Dust and dirt will not enter interior.

(Enclosure protects against foreign objects.)

There are no adverse effects from a water stream

from any direction.

(Enclosure protects against water intrusion.)

There are no harmful effects from oil droplets or

spray from any direction. (Enclosure protects

against oil intrusion.)

F150-VKP (2m)

F150-VKP (5m)

Special Cable for the Console

RS-232C connector (9-pin)

CQM1-CPU21/CPU41-V1/CPU42-V1/CPU43-V1/CPU44-V1

CQM1H-CPU11/CPU21/CPU51/CPU61

C Series: CQM1

RS-232C connector (9-pin) (Only peripheral port for CQM1H-CPU11)

C Series: CQM1H

C Series: C200HS

C Series: C200HE (-Z)

C Series: C200HG (-Z)

C Series: C200HX (-Z)

CS Series: CS1G

Controller Link

Interface Unit

For Controller Link

Communications

NS-CLK21

C200HS-CPU21/CPU23/CPU31/CPU33

C200HE-CPU32(-Z)(See note.)/CPU42(-Z)

Transmission distance:

500 m total length

Note: Use this model when

connecting PT models without a V

suffix.

Note: PT models with a suffix of V

can also be connected.

RS-232C connector (9-pin, selectable)

C200HG-CPU33(-Z)(See note.)/CPU43(-Z)/CPU53(-Z)(See note.)/CPU63(-Z)

C200HX-CPU34(-Z)(See note.)/CPU44(-Z)/CPU54(-Z)(See note.)/CPU64(-Z)/CPU65-Z/CPU85-Z

CS1G-CPU42(-V1)/CPU43(-V1)/CPU44(-V1)/CPU45(-V1)

NS-AL002

RS-232C connector (9-pin)

RS-422A

Adapter

Note: May not be applicable in environments with long-term exposure to water or oil.

CS Series: CS1H

CS1H-CPU63(-V1)/CPU64(-V1)/CPU65(-V1)/CPU66(-V1)/CPU67(-V1)

Transmission distance:

50 m total length

Note: Only PT models with a suffix

of V are connectable. Use the

NS-002 to connect models without

a V suffix.

CVM1/CV Series:

CV500/1000/2000 or

CVM1

CV500-CPU01-V1/CV1000-CPU01-V1/CV2000-CPU01-V1/

CVM1-CPU01-V2/CPU11-V2/CPU21-V2

RS-232C connector (9-pin, selectable)

Meets International Standards and

Exports are Not Restricted

The PTs conform to UL standards (cULus) and EC

Directives.

In addition, there are no export restrictions on the PTs.

cULus certification is scheduled for the near future for

the NSH5 5-inch Hand-held PT.

CJ1W-CIF11

Note: The C200HW-COM02, C200HW-COM04, C200HW-COM05, or C200HW-COM06(-V1) Communications Board is required.

NS12/10

NS12-KBA04

NS7-KBA04

Anti-reflection Sheets

(5 surface sheets)

NS8

NS5

NT30-KBA04

NS12-KBA05

NS7-KBA05

Standard Models

NS12/10

NS8

Protective Covers

(5 pack)

(anti-reflection coating)

Sheet/Cover

Model

Specifications

Model number Standards

Model name

Specifications

Model number

CXONE-AL01C-E

Ethernet Case color

name

NS5

NT31C-KBA05

NS12-KBA05N

NS7-KBA05N

NT31C-KBA05N

CU, CE

CE,

The CX-One is an integrated

tool package that provides

programming and monitoring

software for OMRON PLCs and

components. The CX-One runs

on any of the following

operating systems:

Windows 98 SE, Me, NT 4.0

(Service Pack 6a), 2000 (Service

Pack 3 or higher), or XP.

CX-Designer version 1. is

included in the CX-One.

Refer to the CX-One catalog

(R134) for details.

Ivory

NS12-TS00-V2

NS12-TS00B-V2

NS12-TS01-V2

NS12-TS01B-V2

NS10-TV00-V2

NS10-TV00B-V2

NS10-TV01-V2

NS10-TV01B-V2

NS8-TV00-V2

1 license

NS12/10

NS8

Protective Covers

(5 covers included)

(Transparent)

Black

12-inch TFT

800 x 600 dots

NS12

Ivory

Yes

3 licenses

CXONE-AL03C-E

NS5

Black

(NT625C/631/631C Series to NS12/10 Series)

(NT625C/631/631C Series to NS12/NS10 Series) (Black)

(NT610C Series to NS12/10 Series)

(NT620S/620C/600S Series to NS8 Series)

(NT600M/600G/610G/612G Series to NS8 Series)

30 MB

CX-One

NS12-ATT01

Ivory

FA Integrated

Tool Package

Ver. 1.1

10 licenses CXONE-AL10C-E

NS12-ATT01B

NS12-ATT02

Black

10-inch TFT

640 x 480 dots

NS10

NS8

Ivory

Yes

NS8-ATT01

NS8-ATT02

HMC-EF372

HMC-EF672

30 licenses CXONE-AL30C-E

50 licenses CXONE-AL50C-E

Black

Ivory

(See note 2.)

Black

NS8-TV00B-V2

NS8-TV01-V2

Memory Card

8-inch TFT

640 x 480 dots

64 MB

Ivory

The CX-Designer can also be ordered individually using the following model number.

Yes

Memory Card Adapter

Battery

HMC-AP001

CJ1W-BAT01

Black

NS8-TV01B-V2

NS5-SQ00-V2

NS5-SQ00B-V2

NS5-SQ01-V2

NS5-SQ01B-V2

NS5-TQ00-V2

NS5-TQ00B-V2

NS5-TQ01-V2

NS5-TQ01B-V2

NS5-MQ00-V2

NS5-MQ00B-V2

NS5-MQ01-V2

NS5-MQ01B-V2

OS: Window 98 SE, Me, NT 4.0

(Service Pack 6a),

2000 (Service Pack 3 or

higher), or XP.

Ivory

CX-Designer

Ver. 1.

Bar Code Reader

(Refer to the Catalog for details.)

1 license

NS-CXDC1-V1

XW2Z-S002

V520-RH21-6

Black

5-inch STN

320 x 240 dots

The Ladder Monitor Software

is included.

Ivory

Note: One screen cannot display two video inputs simultaneously.

Yes

Black

Screen transfer cable for DOS/V

Ivory

USB Host Cable, cable length: 5 m

USB Host Cable, cable length: 2 m

NS-US52 (5 m)

NS-US22 (2 m)