MADE IN
User’s Guide
Shop online at
www.omega.com
e-mail: [email protected]
Forlatestproductmanuals:
omegamanual.info
RD8300
Recorder
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 TABLE OF CONTENTS:
General Description............................................................................................... 1
2.3.1 Display Area .....................................................................................................................................4
2.3.2 Media Door .......................................................................................................................................5
2.3.3 Status Indicator.................................................................................................................................5
2.3.4 IR COMM Port ..................................................................................................................................5
2.3.5 Stylus................................................................................................................................................5
Recorder Rear Panel.............................................................................................. 6
2.4.1 Power Supply....................................................................................................................................6
2.4.2 Analog Inputs....................................................................................................................................6
2.4.3 Input/Output Module.........................................................................................................................7
2.4.4 Computer Interface...........................................................................................................................7
Files......................................................................................................................... 8
2.5.1 Configuration Files............................................................................................................................8
2.5.2 Data Files..........................................................................................................................................9
2.5.3 Activity Files......................................................................................................................................9
2.5.4 Miscellaneous Files ..........................................................................................................................9
2.10 Activity Lights ...................................................................................................... 11
2.11 Security................................................................................................................. 11
2.11.1 User Levels.....................................................................................................................................12
2.11.2 Remote Access Passwords............................................................................................................12
3.1.1 Initial Inspection..............................................................................................................................13
3.1.2 Unpacking Procedure.....................................................................................................................13
3.1.3 Detected Damage...........................................................................................................................13
Page i
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1.0 Table of Contents
3.1.4 Equipment Return...........................................................................................................................13
3.1.5 Storage ...........................................................................................................................................13
Environment and Location.................................................................................. 13
3.3.1 Panel Mounting...............................................................................................................................15
3.4.1 Power Requirements......................................................................................................................17
3.4.2 Power Connections ........................................................................................................................17
3.4.3 Signal Input Wiring .........................................................................................................................18
Analog Inputs....................................................................................................................................................... 19
3.4.4 Relay Output, Contact Input ...........................................................................................................21
USB Connection................................................................................................... 22
3.10 Isolated Serial Interface (Option)........................................................................ 23
4.1.1 Live Display Area............................................................................................................................24
4.1.2 Task Bar .........................................................................................................................................24
Utility Setup Menu................................................................................................ 25
Record Session.................................................................................................... 27
Configuration Manager........................................................................................ 28
4.8.1 Display Brightness..........................................................................................................................30
4.8.2 Background Color...........................................................................................................................31
Page ii
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1.0 Table of Contents
Timer/Totalizer Reset........................................................................................... 31
4.10 Special Events...................................................................................................... 31
4.10.1 Record on Alarm.............................................................................................................................31
4.10.2 Record on External Event...............................................................................................................31
4.10.3 Email on Alarm Event.....................................................................................................................32
4.11 Turning the unit off .............................................................................................. 32
4.12 Annotating Trends ............................................................................................... 33
4.12.1 Drawing on the Screen...................................................................................................................33
4.12.2 Adding a Text Message..................................................................................................................34
4.13 Browsing Historic Data........................................................................................ 34
4.13.1 Zoom and Compress Data .............................................................................................................35
4.13.2 View Memos and Bitmaps..............................................................................................................36
4.13.3 Using the Cursor.............................................................................................................................36
4.13.4 Using Browser Jump To .................................................................................................................37
4.14 Browsing Annotations......................................................................................... 37
5.1.1 Master Channel Setup....................................................................................................................38
5.1.2 Channel Setup................................................................................................................................39
5.1.3 Channel Type Setup.......................................................................................................................40
Linear Input.......................................................................................................................................................... 40
Industrial Square Root Extraction......................................................................................................................... 41
Calculated Input................................................................................................................................................... 42
Conditional Input.................................................................................................................................................. 44
Gated Timer......................................................................................................................................................... 44
Totalizer............................................................................................................................................................... 45
Display Builder..................................................................................................... 49
5.2.1 Building the Display........................................................................................................................49
5.2.3 Rotate List.......................................................................................................................................51
Widgets................................................................................................................. 52
5.3.1 Digital Displays ...............................................................................................................................52
Digital Display Setup............................................................................................................................................ 52
Page iii
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1.0 Table of Contents
5.3.2 Bar Graphs .....................................................................................................................................54
Bar Graph Setup.................................................................................................................................................. 54
Trend Setup......................................................................................................................................................... 57
Alarms................................................................................................................... 59
5.4.1 Alarm Master Setup........................................................................................................................60
Alarm Setup......................................................................................................................................................... 61
5.5.1 Digital Output Setup .......................................................................................................................63
5.5.2 Digital Input Setup ..........................................................................................................................64
5.6.1 Select Channels .............................................................................................................................66
5.6.2 Media and Filename.......................................................................................................................67
5.6.3 Record Rate....................................................................................................................................67
5.6.4 What to Record...............................................................................................................................67
Point type – Max Min Average.............................................................................................................................. 67
5.6.5 Timed Record .................................................................................................................................68
5.6.6 Split Files ........................................................................................................................................68
5.6.7 Triggered Record............................................................................................................................68
5.6.8 Media Alarm....................................................................................................................................69
5.7.1 Temperature Compensation...........................................................................................................72
5.7.2 System Setup .................................................................................................................................72
Mouse Pointer Enable.......................................................................................................................................... 73
Menu Timeout...................................................................................................................................................... 73
Unit Tag............................................................................................................................................................... 73
5.7.3 Date/Time Setting...........................................................................................................................73
5.7.4 User Setup (Password Management) ............................................................................................74
5.7.5 File Explorer....................................................................................................................................75
5.7.6 Network Settings ............................................................................................................................76
5.7.7 Web User Manager ........................................................................................................................76
5.7.8 SMTP Email Settings......................................................................................................................77
5.7.9 Set ActiveSync Password...............................................................................................................77
Page iv
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1.0 Table of Contents
5.7.11 Languages......................................................................................................................................79
5.7.12 System ReFlash .............................................................................................................................79
Ethernet Protocols............................................................................................... 86
6.3.1 OPC Server ....................................................................................................................................86
6.3.2 Modbus Server ...............................................................................................................................87
USB Connections................................................................................................. 89
6.5.1 FTP Manager..................................................................................................................................90
6.5.2 Remote Control ..............................................................................................................................93
7.3.1 Calibrating Linear Voltage Inputs: ..................................................................................................96
Set Channel ........................................................................................................................................................ 96
Zero Cal .............................................................................................................................................................. 96
Full Cal................................................................................................................................................................ 96
Store Cal............................................................................................................................................................. 97
7.3.2 Calibrating the RTD Current Source ..............................................................................................97
7.3.3 Calibrating Frequency: ...................................................................................................................97
ANALOG MODULE:............................................................................................ 102
Page v
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Safety Precautions
NOTE
The contents of this manual are correct at the time of issue. The contents may change at any time without prior
notification. This is due to continuous developments to the recorder and its functionality.
Trademarks
Microsoft, MS-DOS, Windows, Windows 2000, Windows XP and Windows CE are all registered trademarks
of Microsoft Corporation.
CompactFlash™ and CF (logo) are trademarks of the Compact Flash Association (CFA).
For the purpose of the manual the ™ and ® symbols will not follow their own trademark names or registered
trademark names.
Company names and Product names mentioned in this manual are trademarks or registered trademarks of
their individual owners.
Symbols
One or more of the following symbols may appear on the recorder labeling.
Refer to manual for instructions
Caution - Risk of electric shock
Earth (ground) terminal
Directive 2002/96/EC WEEE: Waste Electrical and Electronic Equipment
Page iv
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Safety Precautions
WARNING AND SAFETY NOTICE
This Safety Notice has been included to emphasize the DANGER OF HAZARDOUS VOLTAGES on
the REAR TERMINAL PANEL of your instrument. USE EXTREME CAUTION WHEN INSTALLING
OR SERVICING your instrument. Please read the entire contents of Section 2 - Installation and
Wiring within this manual before attempting to install or service your instrument.
1. Before any connections are made to the recorder, ensure the protective earth terminal is connected to a
protective conductor.
WARNING
Any interruption of the protective conductor inside or outside the recorder, or disconnection of the
protective earth terminal is likely to make the recorder dangerous under some fault conditions.
Intentional interruption is prohibited.
NOTE: In order to comply with the requirements of safety standard EN61010, the recorder must have one of the
following as a disconnecting device, located within easy reach of the operator, and be labeled as the
disconnecting safety device:
A switch or circuit breaker which complies with the requirements of IEC 60947-1 and IEC 60947-3
A separable coupler which can be disconnected without the use of a tool
A separable plug, without a locking device, to mate with a socket outlet in the building
2. The protective earth terminal must remain connected (even if the recorder is isolated from the mains supply) if
any of the measuring, communications, or relay terminals are connected to hazardous voltages.
3. Whenever it is likely that protection has been impaired, the recorder should be made inoperative and secured
against operation. Contact the factory for assistance.
4. Any adjustment, maintenance and repair of the opened recorder under voltage should be avoided as far as
possible and, if inevitable, should be carried out only by a skilled person who is aware of the hazard involved.
All repairs should be carried out only by authorized service personnel or returned to an authorized repair
center.
5. Where conductive pollution such as condensation or conductive dust is present, adequate air conditioning,
filtering and/or sealing must be installed.
6. Signal and supply voltage wiring should be kept separate from one another. Where this is impractical,
shielded cables should be used for the signal wiring.
7. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the
equipment might be impaired or inadequate.
Page v
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.0 OVERVIEW
This manual applies to Firmware version 1.0 and above. This section gives a system overview of the recorder and
the basic elements involved.
2.1 General Description
The recorder is an 18 channel unit capable of measuring 6 or 12 live inputs which can be a combination of linear
inputs – voltage or current, thermocouples, RTDs, or Frequency. Those channels not associated with live inputs can
be assigned as gated timers, totalizers, calculated or conditional inputs which are referred to as virtual channels. The
recorder is extremely versatile and can be configured in many different ways to suit the user‟s environment. The
user can also install an optional digital input/output module providing up to 12 potential free contact closures and up
to 6 opto-isolated digital inputs that can be set to silence alarms, reset contacts and start recordings.
The recorder‟s firmware is based on the Windows CE embedded operating system providing advanced
connectivity and features. The system is Ethernet aware and runs as a secure web server providing browser
accessibility via web pages and as an ftp server. It also runs an OPC (Open Connectivity) server allowing
connectivity to a large selection of third party Data Access Specification compliant software and the companion
Exhibitor Software, providing real time data update over Ethernet and off line data analysis. The recorder can be
set up to send emails in the event of an alarm. See Section 4.10.3 Email on Alarm Event for more details.
The recorder can save data, alarms and events to a number of sources. The primary storage medium is to
compact flash card that can be locked in the unit. Alternatively the unit can record to internal memory. Data is
saved in an ADO (ActiveX Data Objects) database and is encrypted for security purposes. Internal memory can
be expanded using a Secure Digital (SD) Card that plugs into the rear of the device.
The recorder is security enabled. If password protection is turned on, the unit requires the user to log in to
operate. There are three classes of operators with different access rights – administrator, manager and user. All
operations are logged to the alarm and event log and user privileges can be set to expire by date. The unit can be
set to automatically log users out after a preset time.
In order to use the recorder the user has to set up various parameters to customize the unit to the environment.
This set up is referred to as the configuration. Once configured, the settings can be saved to a configuration file. A
number of default configurations are provided and any of these can be loaded as a default.
2.2
Page 1
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
System Overview
Refer to the figure below:
ALARM
EVENT
MANAGER
DISPLAY &
KEYBOARD
MANAGER
RELAY
OUTPUTS
MASTER
ENABLE
SYSTEM
MANAGER
DIGITAL
INPUT
MANAGER
USB A/B
DIGITAL
INPUTS
RS232/485
MASTER
ENABLE
DATA
STORAGE
MANAGER
AUDIO IO
DATA
MANAGER
ANALOG
INPUTS
Figure 2-1 System Overview
The recorder block diagram shows the major elements of the unit.
The Analog Inputs module scans the live inputs (6 or 12 channel) at a rate of 10 times per second per channel,
converting the analog inputs to digital values and applying a time stamp to the digitized data. The Data Manager
collects this data at a rate of 120 samples per second from the Analog Inputs module and processes it in real
time applying any scaling or linearization as required by user programming, and holds it in a buffer for use by the
rest of the system. This process has the highest priority and runs irrespective of whatever other activity is going
on in the recorder. Data is fed on demand to the following:
Data Storage Manager receives data at a rate set by the user for recording to the media. The media is selected
by the user – compact flash, USB device or internal memory (SD card). The data is buffered till there is a suitable
amount and is then flushed to the selected media.
Display & Keyboard Manager receives data at a rate to satisfy the displays setup by the user, trends, digital or
bar graphs.
Alarm Event Manager receives all data required to do comparison to any user set up alarm. If any alarm is
exceeded the Alarm Event Manager will perform the required user set action, including sounding the alarm,
closing any contacts, updating the display, initiating an email and making an entry in the log.
System Manager receives all data required to keep the various communications servers up to date. This includes
the web, Modbus and OPC servers, and ftp data files.
Page 2
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
The Data Manager is also controls the Analog Inputs calibration process. This is a privileged operation and
allows an administrator to recalibrate the conversion factors and offsets on the various inputs and their associated
ranges. All units are shipped fully calibrated with a default set of calibration parameters stored in non-volatile
memory which may be recalled at any time.
The Data Storage Manager is used to set up the recording parameters required by the user. Recordings can be
started by the user or can be triggered to start as a result of an external event, an alarm condition or at a preset
time, once or on a daily basis. There is also a File Explorer. This is a privileged operation which enables an
administrator to rename, copy or delete files and move files between the various media.
The Alarm Event Manager is used to set up the various alarms on the channels and route events to the
(optional) relay outputs. Various alarm types can be set. The operation of the (optional) relay contacts are also
defined here. This module processes data in real time checking it against the preset alarm conditions and reacting
accordingly as described above. There is a (soft) master enable switch which allows the user to configure alarms
without affecting the actual (optional) relay contacts.
The Digital Input Manager is used to define the operation of the (optional) isolated digital inputs and process
these inputs according to the user set conditions when they occur. Digital inputs can be used to reset timers or
totalizers, acknowledge and reset alarms, force events or start recording. There is a (soft) Master enable switch
which allows the user to configure the (optional) digital inputs without affecting the actual operation of the
recorder.
The Display & Keyboard Manager controls the content of the graphic display and interprets the input on the
display touch screen and passes this information to where it is required. The user can create an infinite number of
visual screens using a combination of widgets – bar graphs, trends or digital displays. All the other modules
communicate with the Display Manager to provide status information to the user.
The System Manager controls the overall operation of the recorder and prioritizes events as required. It also
manages system security and handles the administrative tasks such as importing or exporting configurations. It
services external requests (via the communication ports), controls the email and configures the unit at startup. It
also deals with any peripherals and routes the information accordingly.
Page 3
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.3 Recorder Front
Figure 2-2 shows the front view of the recorder. The recorder has a ¼ VGA color display with touch screen.
Below the display are a lockable media door, status indicator, IR COMM port and stylus used for data entry on the
display.
The recorder is intended to be panel mounted and if mounted correctly using the supplied gasket, the unit is
waterproof to IP65 when the media door is closed and the waterproof lock cover is in place.
DISPLAY AREA
TASK BAR
STATUS
INDICATOR
IR COMM PORT
MEDIA DOOR
LOCK
WATERPROOF
STYLUS
LOCK COVER
Figure 2-2 Recorder Front View
2.3.1 Display Area
The recorder has a ¼ VGA color display (320 x 240 pixels) and can display 24 million colors. The display has
a touch screen over it and is fully interactive. The screen consists of two distinct areas – the task bar with
icons along the bottom of the screen and the live display which is that area above the task bar showing the
live data in either trend, bar graph or digital display widgets. A full description of this is given in Section 3.0.
Page 4
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.3.2 Media Door
The media door is opened by turning the key in the lock ¼ turn clockwise and pulling the door out and down.
Note that in order to meet the water resistance specification (IP65) the door must be closed and locked and
the waterproof lock cover must be snapped over the lock.
Opening the media door exposes the
compact flash card socket and the USB
port. The compact flash card is intended
as the principal recording media,
however the unit will record to a USB
device or to internal memory.
COMPACT
FLASH CARD
SOCKET
USB A
SOCKET
RESET
BUTTON
CARD EJECT
BUTTON
The compact flash card fits into the
socket as shown right. The card eject
button must fold over to the right once
the card is in place. To eject the card, lift
the eject button, press it to pop the card
out then fold it back over. Grab the card
along the left and right edges between
the thumb and forefinger and remove.
Figure 2-3 Media Door Contents
To the left of the card slot is a small
opening. Set back behind this opening is the system reset button. Under normal operation there should be no
need to use this. Using this button may cause loss of data.
2.3.3 Status Indicator
The status indicator is lit when the unit is powered on and blinks during shut down or when the unit is running
off the internal batteries. The internal batteries allow the unit to survive short power interruptions (< 15
seconds) or brown outs, during which time the display blanks and the status indicator blinks.
2.3.4 IR COMM Port
The IR COMM port is an Infrared send/receive port which allows connection to compatible Infrared devices.
Future Option.
2.3.5 Stylus
The stylus is used to do data entry on the touch screen. It is stored in the bottom right of the recorder front
panel. To remove it, depress the exposed top and turn ¼ turn counter clockwise. The stylus is sprung loaded
and will pop out of its docking location. CAUTION: Control removal of the stylus as it is spring loaded.
To return it to its docking location, insert the pointer end into the hole, fully depress it and give it a ¼ turn
clockwise.
Page 5
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.4 Recorder Rear Panel
The rear panel of the recorder is shown below:
BATTERY DISCONNECT
SYSTEM GROUND LUG
24 VDC OUTPUT OPTION
POWER SUPPLY
MODULE
AC POWER
INPUT
OFF
ON
BATTERY BACKUP
ANALOG INPUTS
CHANNELS 7 – 12
(OPTIONAL)
AMBIENT
TEMPERATURE
SENSOR
ANALOG INPUT
MODULE
ANALOG INPUTS
CHANNELS 1 – 6
INPUT/OUTPUT
MODULE
(OPTIONAL)
USB TYPE A
(MASTER)
USB TYPE B
(SLAVE)
RS-232/RS-485
DB9 CONNECTOR
(OPTIONAL)
MEMORY
EXPANSION SLOT
SPEED LED
MOUSE/KEYBOARD
CONNECTOR
ACTIVITY LED
ETHERNET RJ-45
CONNECTOR
USB SELECT SWITCH (UNDER)
AUDIO CONNECTOR
Figure 2-4 Recorder Rear Panel
USB SWITCH
2.4.1 Power Supply
The power supply module is at the top of the recorder rear panel. The rear panel of the universal AC version
is shown in above. On the right is the AC power input socket that takes a standard IEC connector. Screw
terminals are available as an option, as is a DC power supply module. To the left is the optional 24 Volt dc
output option which provides isolated voltage to power external sensors (100mA). Below this is the battery
disconnect switch. The battery is used to enable the system to shut down correctly and survive short power
outages or brown outs. It should be disconnected for storage or shipping purposes. The system-grounding
lug is used to properly ground the recorder on installation. NOTE: See Section 3 for installation and
connection details.
2.4.2 Analog Inputs
The analog input module is available with either 6 or 12 inputs and accepts dc inputs up to +25 volts. These
inputs are isolated from each other and ground and are truly differential. In addition channels 1, 6, 7 and 12
Page 6
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
have an isolated frequency inputs which allows the unit to measure frequency to 10,000 Hz. Between the
terminal blocks is the ambient temperature sensor for thermocouple compensation.
2.4.3 Input/Output Module
The input/output module is optional and provides potential free relay contacts and isolated digital inputs.
2.4.4 Computer Interface
The bottom of the rear panel is the computer interface. At the bottom right hand corner is a small cover
secured by a screw. This is the internal memory expansion slot – it takes standard secure digital memory
cards.
Above this are the two USB ports – the type A port (to the left) is a master port and the type B port is a slave
port. These are mutually exclusive ports and the user needs to select which port will be active. This is done by
using the small slide switch on the underside of the unit – indicated but not shown in Figure 2-4 above. Slide
the switch toward whichever connector is being used. The Type of port selected, A or B depends on what is to
be connected to it.
To the left of these connectors are two mini-din style connectors. The mouse / keyboard connector allows the
use of an external PS2 PC style mouse directly or a PS2 PC style keyboard using an available adapter board
which will accommodate both mouse and keyboard together. The audio connector is to the left and allows the
audio output from the unit to be fed to an external amplifier.
The Ethernet connector is the standard RJ45 type and allows a 100 Mbps (megabits per second) connection
to be made to the network. There are two indicator LEDs, the one on the right shows connection speed either
10 Mbps unlit or 100 Mbps when lit. The led on the left is the activity led and it blinks when the link is active
and data is being transmitted.
On the left is the optional RS232/RS485 legacy connector. This is a factory installed option. Normally there is
a blanking panel over the opening.
Page 7
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.5 Files
2.5.1 Configuration Files
The recorder has hundreds of options and settings that need to be set up by the user. Things like input types,
point tags, displays, record information and so-on. Once set up, this information is saved in the internal
memory (SD Card) as a user named configuration file in a special directory called ConfigFiles. Each unique
configuration is stored in a sub-folder within the ConfigFiles directory. The system appends “_cfg” to each
folder name created which in turn contains the actual configuration files. The files are in an xml format and
bear the extension “.xml”. Currently there are two independent but related files – one for the physical settings
of the recorder – input types, record setup, alarms and so on and has the filename given by the user with the
file type “.xml” and one for the displays as set up by the user which has the filename given by the user but has
When a user saves or loads a configuration using the Configuration Manager the system takes care of the
details and defaults to the ConfigFiles directory.
When saving the configuration, the user enters a filename and accepts the entry – for example the filename
could be “pumphouse”. The Recorder will then create a folder in the ConfigFiles directory called
“pumphouse_cfg” and in this folder it will create the two configuration files, “pumphouse.xml” for the physical
settings and “pumphouse_displays.xml” for the display information.
When loading a configuration, the Configuration Manager will show a list of all the subfolders (Configurations)
in the ConfigFiles directory (without the “_cfg” adder) so the user can recognize the configuration files. When
a configuration is selected, the system loads the two files from this subfolder.
At the recorder, this folder and split file structure is totally transparent and configurations can be loaded using
names assigned by the user. When using the file explorer to move configuration files it is important to note
that you need to move, save or copy the subfolder in the ConfigFiles directory. This will keep all associated
file with that configuration together.
The structure is as follows:
.
Page 8
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
Eg: To copy the “pumphouse” configuration to a different media you need to go to the ConfigFiles directory
and copy the FOLDER “pumphouse_cfg”.
In the root of the internal memory (SD card) are two files – config.xml and displays.xml. These are the default
configuration files used by the system. When you quick-save a configuration, this is where it saves to. You
should not transport these files but rather save the configuration as mentioned above.
2.5.2 Data Files
When data is recorded, the unit creates a folder in the root directory of the selected media with the name
given in the Record Setup menu. This folder contains all files generated during the record session. The
primary data file is in this folder and has the extension “.dat”. So if you set up to record to the compact flash
card and name the file “session1” the recorder will create a folder on the compact flash card (CF CARD)
named “session1”. In this folder will be a file “session1.dat” which is an ActiveX Data Object File (ADO) and is
the primary database containing all the recorded channel data as well as alarm and event data for the record
session if this has been enabled. The file size is dynamic and depends on how many channels are being
recorded, the record rate (samples/second) and how active the data is (static data results in reduced file size.
It is not unusual for active data recorded at high speeds to result in large files. Any annotations should be
saved in this folder (they save as “.bmp” files) to keep all record session information together. The “.dat” files
can be transported or moved using the FTP manager, and can be analyzed on the PC using the Exhibitor
software.
2.5.3 Activity Files
The activity files are saved when the Activity Log check box is checked in the User Setup Menu. The Activity
Logs are stored in the Activity Folder in internal memory (SD Card). These files are used for FDA 21 CFR
Part 11 compliance. The files are created whenever a user logs on or logs off. Using the Exhibitor software an
administrator can print out a report of all changes made by that user during the time they were logged into the
recorder. The files created are in the form: user-date-sequence-“start config” and user-date-sequence-“end
config” and are xml types.
The Administrator should purge these files periodically to free up space.
2.5.4 Miscellaneous Files
The recorder saves alarm and event information in the root of the internal memory (SD Card) in log files
AlarmFile.Log and EventFile.log. These files are encrypted and can be decrypted and printed using the
Exhibitor program running on the PC.
2.6 Exhibitor Software
The Exhibitor software is a program that runs on the PC that allows a user to plot and print data recorded on
the recorder. This data may be retrieved remotely, displayed in graphic or tabular format or be exported in
various formats including ExcelTM format. Additionally it allows a user to view Event and Alarm Logs and
analyse data, search for highlights and parse data for minimums or maximums. It can also be used to gather
data in real time from remote recorders, create real time widget displays, print reports and configure remote
recorders. A lite version of the software is provided with each recorder and can be upgraded to various
capabilities.
Page 9
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.7 QUICK START GUIDE
The recorder ships in a fully functional mode, but may not be set up the way you would want to use it and needs
to be configured before it is used.
There are several areas that need to be configured to customize the unit to the user‟s needs. This unique
combination of settings is referred to as the system configuration and is saved in a file called the configuration
file which is physically named config.xml. This file is reasonably human readable and is in XML (Extensible
Markup Language) format. This file resides in the recorder‟s internal memory and is portable. On start-up the
recorder loads this file and configures itself accordingly. There can be numerous configuration files in the
recorder, however only one can be called config.xml. See the Configuration Manager on page 28. If no
configuration file is present at startup, the unit will create one which will have minimal functionality.
The most basic setup needs to define the inputs, create a display and set up a recording. You may need to set
the time and calibrate the touch screen. The setup can then be extended to include alarms, contact outputs
(requires an optional digital I/O module), digital inputs, various display options, and conditional events (like
recording on alarm or sending emails).
The first thing to do is to browse this manual to get some idea of the features of the unit. The following will steer
you to various sections based on a quick set up. Help is available at each screen and you should see the section
on keyboarding before you start anything.
Naming the Recorder: You should give the recorder a unique name to identify it such as “Soap Plant Boiler”.
Analog Setup: You will then need to set up the analog inputs to meet the requirements of the signals you will be
measuring. The recorder has universal inputs capable of measuring a variety of signals from millivolts to Volts,
Current, Resistance, Thermocouples, RTDs and on some channels, Frequency. All channels can also be
assigned as virtual channels, that is they do not have a direct live inputs, but can be Calculated channels, Timers,
Totalizers or Conditional. The analog inputs are set up in the Master Channel Setup menu. Each channel can be
uniquely programmed and has a Channel Tag to identify the channel, eg. “Pump 6”. These settings will apply to
Display Creation: Once the inputs are set up you need some way of displaying the data. This is done on the live
display. To appreciate what this entails check out the section on Display Elements and Widgets. Then use the
Display Builder to create the actual display. This builder allows you to place the widgets on the screen and
customize each and give the display a name. In order to have the display come up on the screen you need to
Recording Data: To record data you need to use the Record Setup dialog to select which channels to record,
what to record, at what rate and where to save it. Data can be saved to internal memory, compact flash card or
USB flash drive.
To record the data you must have set up the recorder as mentioned above.
Icon Buttons: There are several buttons with icons used on the recorder. Specific ones are described in the
respective sections. Generic ones are shown below.
Okay or
Accept
Cancel
Exit
Reset or
Refresh
Setup
Edit
Color
(Foreground)
Background
Color
Page 10
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.8 Keyboarding
While it is possible to connect a standard keyboard and
mouse to the recorder, one may not be readily available
in which case data is entered using the pop-up keyboard
as shown right.
When you enter a recorder setup screen where it is
necessary to type in data, the instant you tap the input
field box the keyboard pops up. Entry is made by tapping
the keys firmly with the stylus. As each key is pressed it
inverts its color. The Shift key allows a one time
uppercase letter to be entered and pressing the CAP key
will lock the keyboard in uppercase. The keyboard can be
moved by pressing in the gray area where it says Input
Panel and dragging it out the way in the event you need
to access an entry point behind the current location.
Figure 2-5 On-screen Keyboard
2.9 Help
Help is available on most set up screens by
tapping the help icon (shown left) on the right of
the blue name bar near the bottom of the screen – see
Figure 2-5 above. This will bring up a help text file which
deals specifically with the subject at hand.
The scroll bar at the right of the screen can be used
to browse through the file.
Tap the DONE button to exit.
Figure 2-6 On-screen Help
2.10 Activity Lights
At the bottom right of the display are three small square activity „lights‟, the top one being white, the middle green
and the bottom black.
These have no purpose for the user other than “feel good” indicators to
indicate everything is working internally. The white block is the analog
subsystem activity and blinks at around 3 Hz. The green block indicates
internal data execution and the black block is the internal watchdog and
blinks at a rate around once every 3 seconds.
Figure 2-7 Activity Lights
2.11 Security
The recorder has several levels of password to protect the various functions and prevent unauthorized access to
the unit. Access can also to limited access and control who can make changes, who can access and who can
administer the unit.
Page 11
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2 - Overview
2.11.1 User Levels
There are three user levels for gaining direct access to the recorder. User levels are only active if security is
enabled. The three levels are
Administrator:
Manager:
Has access to all levels of the recorder menus and systems.
Has restricted access. A Manager cannot set up any base level parameters, but can use
existing setups to create alarms, displays and the like.
User:
Can use the recorder only as set up by the Administrator or Manager. A User cannot
change any parameters. A User needs to log in to accept alarms.
User management is an Administrative only function and is controlled in the System Administrative Menu.
Here the Administrator can set usernames and passwords, disable users, set user expiry times and force a
user to be logged out after a specific time. The number of log in attempts can also be set before the current
user is disabled.
All users need to log in to the unit to perform any functions. At each log in the recorder makes a note of the
time and user name and will also log any failed attempts at login. Each user has a unique username and
password. Users may change their passwords at any time at the log in screen.
The unit also saves a copy of the configuration file when the user logs in and when the user logs out. This
way a complete activity log can be generated (by the accompanying Exhibitor software comparing the two
configuration files) and all parameters changed can be reported.
2.11.2 Remote Access Passwords
The user can access the recorder remotely using various methods. Each method is protected by a unique
follows:
USB Access: Password optional. When accessing the unit via the USB Connection using ActiveSyncTM or
VistaTM Mobile Manager the Administrator can set an optional password which needs to be entered from the
HTTP Access: Password required. When accessing the web server using the Ethernet and a browser the
user has to provide a password. There are two levels of password Admin and User. Users can view the web
pages but only Admin can perform remote functions. These passwords are set in the Web User Manager and
the Administrator user name HAS to be Admin.
FTP Access: Password Required. This is the same Admin password used for HTTP Access. No User access
is permitted.
Remote Control over Ethernet: Password Required. These are the same user names and passwords set for
recorder front panel access through the User management option described above.
All access user names and passwords can be set to be the same provided the administrator user name is
Admin. However you do have to set these up at the various locations referred to above.
Page 12
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.0 INSTALLATION
This section provides information and procedures on installing and wiring the recorder. Included are handling
procedures, installation and wiring specifications, and instructions for both standard and optional equipment.
3.1 Equipment Handling
3.1.1 Initial Inspection
Exercise care when unpacking the instrument from the shipping carton. The instrument is packed in a
shockproof foam retainer to prevent damage during normal transit. If damage to the shipping carton is
evident, ask the carrier‟s representative to be present when the instrument is unpacked.
3.1.2 Unpacking Procedure
To unpack your recorder, first remove the foam retainer and instrument from the shipping carton. Then,
carefully remove the instrument from the foam retainer.
3.1.3 Detected Damage
If damage is detected after unpacking the instrument, re-pack the instrument and return it to the factory as
described in the following section.
3.1.4 Equipment Return
Before returning a damaged or malfunctioning instrument to the factory for repairs, contact the sales
organization from which you purchased the instrument. A Return Merchandise Authorization number must be
obtained from the factory before returning an instrument for any reason.
3.1.5 Storage
For prolonged storage before installation, re-pack the recorder in the shipping container. Cushion the
recorder with foam molding or an equivalent and store in a cool, dry area. It is not recommended to store the
recorder for more than one year. If longer storage time is required, contact the factory for additional storage
information.
3.2 Environment and Location
The instrument is intended to operate in the following environment:
Indoor Use Only
Installation Category II
Pollution Degree Level II
Altitude
per IEC 664
per UL3111-1 / IEC61010-1
up to 2,000 m
Temperature
-10 °C to +50 °C operating per UL3111-1 / IEC61010-1
Humidity
Maximum relative humidity 80% for temperatures up to
31°C decreasing linearly to 50% relative humidity at 40°C
AC Mains Supply
100 - 240 Vac ~ 50/60 Hz 35 Vac ±10%
Page 13
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
NOTE: The recorder is designed to be panel mounted and as such should be considered as
permanently connected. Disconnection from the supply must be possible via a customer
supplied switch or circuit breaker. This disconnection device must be included in the panel
installation and should be clearly marked, in close proximity to the Recorder and easily
accessible to the operator.
3.3 Installation
The recorder is sized to fit in a standard DIN panel cutout of 5.43” x 5.43” [138 mm x 138 mm] and requires a
minimum of 6.5” [188.2 mm] behind panel depth not including power and input source cable space needed.
Actual dimensions are shown below.
Figure 3-1 Recorder Dimensions in Inches [mm]
WARNING:
Do not use this instrument in any manner inconsistent with these operating instructions or
under any conditions that exceed the environmental specifications stated.
Page 14
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.3.1 Panel Mounting
The recorder should be mounted in a vertical panel to ensure proper operation. Note that the locking bars can
be used on the sides or top and bottom of the unit depending on available space. Ensure you have the proper
clearances and proceed as follows:
3.3.1.1 Cut a panel opening 5.43” x 5.43” [138 mm x 138 mm]. Units can be mounted as close as 0.6”
[15.2mm] between opening cutouts
Figure 3-2 Front Panel Cut Out
3.3.1.2 Remove any packaging material from the recorder. Always handle the unit carefully to avoid
damaging the LCD display or scratching the display surface.
3.3.1.3 Remove the locking bars from the recorder enclosure and ensure the gasket is not twisted on the
enclosure.
3.3.1.4 Insert the recorder rear end first, into the panel opening from the front of the panel as shown in
3.3.1.5 With the recorder held firmly in place against the panel, install one of the locking bar assemblies
by sliding the locking bar notch into the slot on the side (or top) of the recorder enclosure as
3.3.1.6 Using a slotted screwdriver, tighten the screw until the locking bar is just pressing against the
panel.
3.3.1.7 Install the other locking bar assembly into the slot on the opposite side (or bottom) of the recorder
enclosure and tighten as before.
3.3.1.8 Using the screwdriver, tighten both screws so that the recorder is held firmly in place. Do not over
tighten.
3.3.1.9 Use the supplied silver “stickers” to seal the unused locking bar slots on the top and bottom or
sides of the unit
Page 15
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.4 Wiring Specifications and Procedures
3.4.1 Power Requirements
The recorder operates on any voltage from 100 to 240 Vac +10%, 50/60 Hz enabling it to be used in most
countries. The maximum apparent power required by the unit is 35 VA.
3.4.2 Power Connections
NOTE: The recorder is designed to be panel mounted and as such should be considered as permanently
connected. Disconnection from the supply must be possible via a customer supplied switch or
circuit breaker. This disconnection device must be included in the panel installation and should be
clearly marked, in close proximity to the recorder and easily accessible to the operator.
All connections to the recorder are made to the Rear Terminal Panel. Any wiring carrying hazardous voltages
must conform to all applicable local and national safety codes. AC Mains connection is via an internationally
accepted IEC 320 AC mains connector or screw terminal (Figure 3-5 and Figure 3-6).
WARNING Ensure all mains power is turned off before proceeding with
installation. This unit is provided with a mating connector for the ac power socket or
with a compatible three wire grounded cable which may be terminated with a plug.
Always ensure the ground wire (green or green and yellow) or ground pin of the plug,
is connected to a low impedance safety ground (earth) within the ac power distribution
system you are using. Always use the recommended mating connector and an
approved three wire cable to connect this unit to the ac mains. Always provide a low
impedance safety ground wire to the ground lug on the rear panel marked.
Figure 3-5 shows the IEC 320 AC mains connector on the rear of the recorder. The center
pin is the ground termination. If a mating plug is provided, it will be marked with the Ground,
LINE (L) or hot, and NEUTRAL (N) or return. In the United States, an approved cable with
integral plug (NEMA 5-15 P) is provided. In some instances, a cable with no plug may be
provided. In this instance, the user must connect an approved plug to the cable prior to
connecting to the AC source.
Figure 3-5
Figure 3-6 shows the screw terminal power connections on the rear of the recorder. The right
terminal is ground, the center terminal is LINE (L) or hot and the left terminal is NEUTRAL (N)
or return. The wire color codes are as follows:
Figure 3-6
Figure 3-7 shows the ground lug on the rear panel. This screw terminal must be connected to
an earth wire which in turn is connected to the ground or earth of the AC power distribution
system.
This unit is equipped with an AC mains fuse internally. If this fuse should blow, it generally
indicates a serious problem with the recorder. THE FUSE SHOULD NOT BE REPLACED
BY AN OPERATOR. The fuse is a quick acting 5 x 20mm type - 2.0 Amps 250 VAC (~).
Figure 3-7
Page 17
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.4.3 Signal Input Wiring
Signal input connections. Hazardous potentials may exist on signal input terminals
which are floating with respect to case ground. These hazardous potentials may be
on the rear terminal panel of your instrument. Any voltage potential at the signal
source will exist on the instrument’s respective signal input terminal (i.e. power
generator stator winding). The analog inputs can sustain up to 2000 Volts with
respect to the chassis ground.
The recorder accepts up to twelve direct inputs. Input connection is via plug in screw terminal connectors on
the rear panel. Inputs can be mixed in any combination of thermocouple, RTD, milliamps, millivolts, volts or
contact inputs. In addition, channels 1 and 6 (and optionally 7 and 12) can accept frequency inputs via an
additional terminal. There is a common ground lug marked with a
or screens.
for connection of signal cable shields
-
+
24VDC OUT
ON
OFF
90 - 240 VAC 35 VA
BATTERY BACKUP
FIN IN+ IN- COM
CHAN 7
IN+ IN- COM
CHAN 8
IN+ IN- COM
CHAN 9
IN+ IN- COM
CHAN 10
IN+ IN- COM
CHAN 11
IN+ IN- COM FIN
CHAN 12
FIN IN+ IN- COM
CHAN 1
IN+ IN- COM
CHAN 2
IN+ IN- COM
CHAN 3
IN+ IN- COM
CHAN 4
IN+ IN- COM
CHAN 5
IN+ IN- COM FIN
CHAN 6
RELAY
1
RELAY
2
RELAY
3
RELAY RELAY
RELAY
6
RELAY
7
RELAY
8
RELAY
9
RELAY
10
RELAY
11
RELAY
12
-
-
+
+
4
5
DIGITAL 1 DIGITAL 2
USB
SLAVE B
AUDIO KEYBOARD /
OUT MOUSE
USB
MASTER A
RS232/485
ETHERNET
Figure 3.8 – Rear Panel
Page 18
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
Read the following procedures prior to connecting inputs to the terminals.
WARNING: Ensure the power is off before connecting signal inputs to the unit.
The plug in screw terminal connectors are of the clamping screw variety, putting even pressure on the signal
wire. It is therefore not necessary to terminate the wires with lugs, however you may do so if you wish. The
maximum gauge wire that can be accommodated is 14 AWG or 2.5 mm². You will need a small screwdriver
and a pair of wire cutters and strippers. The use of shielded twisted lead wire is recommended to minimize
electromagnetically induced noise.
WARNING: All unused inputs must have + and - contacts commoned together.
CAUTION: Never run signal and power or control wiring together in the same conduit. This is to
prevent possible recording error due to induced signals between lines. If running cables
is inevitable, use shielded cable where possible and properly ground the shield. Route
signal wires away from power wires at the rear panel.
NOTE:
Ground cable shields at one end only to eliminate the possibility of interference due to
ground loop currents. When grounded transducers are used, the shield should be
grounded at the sensor end only.
3.4.3.1 Analog Inputs
The Analog Input board can have 6 or 12 channels (12 shown below). Each Input is truly differential and
has a positive (IN+) and negative (IN-) input and an RTD Common (COM) for RTD current return and
Frequency input Common ONLY. Channels 1 and 6 (and optionally 7 and 12) have a Frequency Input
(FIN) which is common with the COMmon input. All inputs are isolated to 350 Vac from each other and
2,000 Vac from the chassis ground.
Figure 3-9 Analog Input Module (12 Channels shown)
3.4.3.2 Thermocouple Inputs
Thermocouple Input connections are made as shown in Figure 3-10 T/Cs. The ambient temperature
compensator is between inputs 3 and 4.
3.4.3.3 Resistance Temperature Detector (RTD) Inputs
Two or three wire RTDs may be used for connection with cable compensation of up to ±50 ohms. The
“COM” Terminal is the common current return (Wire 3). Four wire RTDs can be used – simply do not
connect the second + wire. Two wire RTDs require a jumper between (IN-) and (COM). Refer to Figure
3-10
3.4.3.4 Linear Inputs
Linear Inputs are divided into two types:
Current inputs:
Voltage inputs:
4-20 milliamps, 0-20 milliamps and 10-50 milliamps, using an external 50 ohm
shunt (0.1% 0.5W).
+125mV, +250mV, +500mV +1.00V, +3.0V, +6.0V, +12.0V, +24.0V DC.
Page 19
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.4.3.5 Potential Free Contacts
Normally open/closed contact inputs.
3.4.3.6 Frequency
Available on channels 1, 6, 7 and 12 only. Default input is for 12 to 24V DC @ 20mA max. The inputs can
50 Ω 0.1%
0.5W
THERMOCOUPLE
VOLTAGE AND CURRENT
RTDs
CONTACTS
NOTE: RESISTOR FOR CURRENT ONLY
CHAN 1, 7 FREQUENCY/PULSE INPUT
CHAN 6, 12 FREQUENCY/PULSE INPUT
Figure 3-10 Analog Inputs - Wiring Detail
Page 20
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.4.4 Relay Output, Contact Input
WARNING
To prevent the possibility of electrical shock, use extreme caution when wiring
contact output connections. Hazardous potentials may exist on contact output
terminals which are floating with respect to instrument ground. These hazardous
potentials may be exposed on the rear terminal panel of your instrument. Any
voltage potentials at the contact circuit will exist on the instrument’s respective
contact output terminals (i.e. line-powered circuits).
The Recorder may be equipped with an optional Digital Input Output Board which has A combination of up to
12 potential free Form A (Single Pole Normally Open) or Form C (Single Pole Double Throw) relay contacts
and up to 6 opto-isolated digital inputs. The combination depends on the option chosen. An example is shown
below.
Figure 3-11 Digital I/O Module 12 Contacts Out, 2 In
This module has 12 Potential Free Form A Normally Open (NO) connections. Connection is two wire and
there is no polarity. Maximum switching voltage is 200 Vdc and 0.5 Amp at a Maximum of 10 Watts (Voltage
x Current <10W) per contact. The potential free relay contacts are protected internally with 270 volt Metal
Oxide Varistors (MOVs) to prevent contact arcing.
There are two optically isolated digital inputs which accept 12 to 24 volt DC inputs (These can be jumpered
internally on the circuit board for 5 to 12 volt DC operation – see Appendix B). The inputs are polarity aware
and are marked plus (+) and minus (-) accordingly. Check the specification of the specific module in your unit
for full specifications.
3.5 Ethernet
The 10BaseT Ethernet option allows direct connection to the LAN or WAN and the
standard TCP/IP protocol enables the transfer of data over the Internet. The RJ45
Connection for the Ethernet is as follows:
Receive Differential Pair
Transmit Differential Pair
3 RX-
6 RX+
7 TX-
8 TX+
Two LEDs on the rear panel show Ethernet activity. The Amber Link Speed LED indicates
address needs to be set before this port will function
Figure 3-12
Page 21
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.6 USB Connection
There are two USB (Universal Serial Bus) Connectors on the rear panel.
One is a Type A Master connector; the other is a Type B Slave
connector. Only one can be active at any time – the active connector is
back panel. The switch is set below the surface. Slide the switch toward
the connector you want active – A or B BEFORE powering up the unit.
Use standard shielded USB connector cables to connect to your USB
device (Host PC to USB B – Slave Device to USB A Host port).
Note: Maximum cable length should not exceed 5m (15 feet).
Figure 3-13
3.7 Audio Connection
The audio output connector is a 6 pin mini din socket that permits connection to the
recorders audio lines. Connections are as follows:
Pin
1
2
3
5
Direction
Out
In
Out
Out
In
Description
Audio Common
Microphone Input
Line Output – Left
Line Output – Right
Line Input - Left
Line Input - Right
4
6
In
Figure 3-14
An adapter is available that converts the Mini Din to 3 Standard Phone Jacks for
Microphone In, Line In and Line Out.
3.8 Mouse and Keyboard Connection
The keyboard / mouse connector is a 6 pin mini din socket that permits connection to an
external mouse and/or keypad. A standard PS2 mouse will plug directly into this socket, a
PS2 keyboard needs an adapter. Connections are as follows:
Pin
4
3
1
5
Direction
Out
Out
In/Out
In
Description
+V for Keyboard/Mouse
Supply Common for Keyboard/Mouse
Mouse Data Line
Mouse Clock Line
2
6
In/Out
In
Keyboard Data Line
Keyboard Clock Line
Figure 3-15
An adapter is available that converts the single Mini Din Socket to two separate sockets, one for the mouse and
one for the keyboard.
Page 22
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3 – Installation
3.9 24Vdc Isolated Output (Option)
The Isolated 24Vdc Output is an option that provides 24 Volts DC @ 100 milliamps to
power external (current loop) sensors. The output is isolated to 1000 volts from all internal
voltages and ground. The output is also protected against short circuit.
The output is polarized and is marked for positive (+) and negative (-). This option is field
installable.
Figure 3-16
3.10 Isolated Serial Interface (Option)
A standard DB9 Female connector is required for the RS232 to connect
to an IBM PC compatible computer using a null modem cable. The
RS232 interface can support cable runs up to 50 feet [16 m]. The RS485
connection is via two wire (twisted pair) cable (a DB9 Female adapter
connector is required) and can support cable runs up to 4000 feet [1300
m].
The RS232 and RS485 connections are mutually exclusive and are
selected using pin 1 of the DB9 connector – see right.
The interface is isolated from internal circuitry to 500 volts. The RS485
Figure 3-17 Serial I/O
requires a 120 ohm terminating resistor if it is the last unit on the drop. All
Serial Interface connections are made through the DB9 female
connector. An adapter connector is included that brings out the RS485
connections to a set of screw terminals and has the terminating resistor on
the board. The RS485 connection is marked A and B for duplex 2 wire
connection. A is + and B is -.
If the terminating resistor is required it is necessary to open the adapter
shell and insert the jumper to enable the termination.
Fig 3-18 RS485 Adapter
The connections to the DB9 female connector are as follows:
DB9 PIN
CONNECTION
DIRECTION
1
2
3
4
5
7
8
6
9
Mode Select (see below)
RxD Receive Data
TxD Transmit Data
DTR Data Terminal Ready
Common
RTS Request To Send
CTS Clear to Send
RS485 A+
In
In
Out
Out
Out
Out
In
Bidirectional
Bidirectional
RS485 B-
The mode select pin (pin 1) must be left unconnected for RS232 operation
or must be grounded (to pin 5) for RS485 communication. Use the provided
adapter for RS485 communication
Fig 3-19 RS485 120 Ohm Jumper
Page 23
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.0 FUNCTIONAL DESCRIPTION
4.1 Display Elements
Digital
Display
Live Display
Area
Trend
Bar Graph
Task Bar
Figure 4-1 Typical Display
A Typical display on the recorder is shown above. The actual content of the window will vary according to what
has been set up by the user. The display has two parts to it - the Task Bar along the bottom of the screen and the
Live Display Area which is the rest of the screen. On power up the Live Display Area will show the default screen
4.1.1 Live Display Area
The Live Display Area shows combinations of trends and widgets as set up by the user in the Display Builder
and enabled in the Rotate List Setup. Tapping the Task Bar along the bottom of the screen will bring up the
next Display View as defined in the Rotate List.
There are three basic styles of widgets viewable in the display –bar graphs, digital displays and trends. For
additional information on creating Live Displays see Display Builder and Rotate List in Section 4.
The display is “active” and much of the display area will react to taps on the screen. Tapping the Task Bar will
cause the live display to move to the next display, assuming you have set up more than one in the Rotate
List. Double tapping the Digital Display or the scale on the Bar Chart and Trends will take you to the widget
setup for that particular widget. Tapping the bar below the Trend will advance the scale to the next channel.
Double-tapping the actual Trend area will take you to the screen annotate function. Double Tapping the lower
area of the Digital Display will allow display of max, min or average values
4.1.2 Task Bar
The Task Bar is the reddish colored bar at the bottom of the screen. It contains a number of button icons and
two lines of information. The label “Recorder Demo” is the Unit Tag and can contain up to 24 characters to
uniquely identify the recorder. It is set in the System Setup Menu. Below the Unit Tag is the Date and Time
Display, which shows the current date and time the recorder is using. Tapping any part of the Task Bar that is
NOT a button will cause the Live Display to rotate through the various views as created by the user and
enabled in the Rotate List.
Page 24
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
There are 5 button icons in the Task Bar. They vary according to the status of the recorder. They are from left
to right:
can configure and control the recorder.
Alarm Contacts Reset Button – This icon shows the status of the optional output contacts. If any
contact is active, this icon will be red and show the contact closed. Pressing this icon will reset any
latched output contact that is reset enabled. User must be logged in to use.
display. When logged in as administrator there is an extra display – the Activity Log.
Alarm Accept Button – This icon indicates the status of the recorder alarms and acts as the Alarm
Accept button. Pressing this button silences the audible alarm tone. User must be logged in to use.
When GREEN it indicates that there are no alarms present.
When AMBER it indicates there are no alarms but the audible Alarm Tone has been muted.
When RED it indicates there are alarms present OR the alarms have been disabled.
Record Icon – This icon indicates the recorder record mode. It changes according to what the
The GREEN background indicates that the recorder is currently NOT recording.
The AMBER background indicates that the recorder is currently ARMED but is NOT recording.
The RED background indicates that the recorder is currently RECORDING. It will blink slowly.
4.2 Utility Setup Menu
Tapping the Utility Setup Menu Icon on the left of the Task Bar brings up the Utility Setup Menu as
shown below. Tapping the icon a second time returns to the original display.
Figure 4-2 Utility Setup Menu
The Utility Setup Menu provides the user with several options. The number in the right hand corner of the blue bar
at the top of the menu is the system memory resource usage as a percentage of available. It does not include
added memory. It should be less than 80% for proper operation. Menu choices are as follows:
Page 25
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
System Admin Menu– Allows the administrator (if security is enabled) to enter the system
administration menu. This allows the recorder to be configured at the base level (passwords,
security etc.) Details Here
Sound Level Adjust – Allows the user to adjust the sound level of alarms and prompts. This brings
up a slider bar. Use this to adjust the volume – audible feedback is provided.
Configuration Manager – Allows the permitted user to import (load), export (save) or clear the
Quick Save Configuration – Press this button to do a quick save of the configuration.
Master Channel (Input) Setup – Allows the administrator to set up and define the input channels.
Master Alarm Setup – Allows the administrator or manager to set up and define the alarms
Digital I/O Setup – Allows the administrator to set up the digital outputs (relay contacts) and the
Send Email – Allows the user to send an email provided the unit has been configured to do so. Log
System Information – Allows the user to see the status of the recorder – firmware versions, user
logged in, unit tag and IP Address.
Display Builder – Allows the user to create live displays using widgets. Log in required
Rotate List – Allows the user to decide which displays appear on the live display when the task bar
Display Utilities – Allows the administrator to adjust the display back light and background color.
Record Setup – Allows the user to start and stop recording and set up recording parameters -
media type, channels, file name, record rate and what to record. Log in required.
If the unit is currently recording the menu icon will have the red dot – pressing the button will allow
the user to stop recording. If the unit is not recording the menu icon will have the green dot –
pressing the button will allow the user to start recording, arm recording or if privileges allow, to set up
Timer/Totalizer Reset – Allows the user to reset any timer or totalizer channel back to zero. Details
Calculator – Allows the user to pop up and use a simple calculator.
User Login – Allows users to log in to the system. Asks for a user name and password. If a user is
already logged in it will ask if the user wishes to log out. Once logged in a user can operate without
Page 26
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.3 Alarm, Event and Activity Logs
While viewing a live display, pressing the Events
button (left) on the task bar brings up the Event
and Alarm logs as shown right.
Each time this button is pressed it will move through a
series of logs – Event -> Alarm -> Activity. Note that the
Activity Log can only be viewed if the user has
administrative privileges.
When in the Event log (Activity Log for
Administrators) the icon changes to that on the
left. Press this button to return to the live display.
The Logs are a record of all alarms, events and activities
that occur in the recorder. The Activity Log is a record of
all operator entries. Each entry is annotated with the
date and time the event occurred together with a
Figure 4-3 Alarm Event Log
description of the alarm, event or activity. If security is enabled the user‟s name will be logged along with the
event. The alarms and events are listed in chronological order with the latest entry at the top of the list. As each
new entry appears at the top of the list, the rest scroll down. Use the scroll bar to view past events. The Logs
display the latest 512 entries of the unlimited entries that are located on the internal memory card as AlarmFile.txt
EventFile.txt and LogFile.txt. The files are encrypted but can be read by the accompanying software.
The files may also be saved to a specific location using the Save As button
The files can be cleared using the Clear button (Admin only).
(Admin only)
The files should be cleared periodically for the sake of efficiency and space.
4.4 Record Session
A record session commences once a file name has been defined in the Record Setup menu and remains open
until a new name is assigned. This file name is the name of the data file that will be recorded to the media and
will contain all the data, alarm and event information as programmed. The recorder will create a folder on the
designated media with the same name as the file name. This folder will contain the data file as well as all ancillary
files associated with this recording – for example annotation bit map dumps. These files may be referenced by the
data file during playback on the PC and should not be separated. When copying or moving use the entire folder
not the files.
Folder: Mydata
Data File: Mydata.dat
Bitmap Files
Text Files
Related Files
Other files that may be associated with the session are the configuration file „config.xml‟ and the Event log
„LogFile.txt‟ and „LogFileHist.txt‟. These files reside on the root directory of the internal memory (SD Card) and
Page 27
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.5 Configuration Manager
The Configuration Manager is entered from the System Admin Menu by pressing the icon shown at
the right. This is a privileged option and allows the administrator to load, save or clear the
configuration file. The configuration files are in a folder of the same name in the ConfigFiles directory
and contain all the set up elements of the recorder and is transportable. See Configuration Files for detail.
Configuration files are in xml format and are human readable and can be edited by any xml editor. There must
always be a config.xml/displays.xml file in the internal memory to ensure proper operation of the unit. This is the
file loaded at start up. If a config.xml file is not found, the unit will start up but will not be fully configured.
Pressing the icon shown will pop up the Config.File window as shown on the right. Select the
operation you require:
Load: This enables the user to load a new configuration. A file browse window
will pop up showing the configuration files available Select the configuration
you want by tapping on it and press okay. Note: This will load the new config file and the
recorder will restart. The old configuration settings will be overwritten.
Save: This enables the current settings
to be written out to the existing
config.xml (the file will be overwritten) or you can
assign a new name and location for it. Note: This new
configuration will not load on startup unless it is called
config.xml and resides in internal memory.
Clear: This will clear the configuration
file and set it to a minimally functional
set of parameters. Use this option if you want to start
over configuring the unit.
Cancel: This allows you to exit without
doing anything.
Figure 4-4 Load Configuration
NOTE: There is an option to save the CONFIG file automatically any time a change is made to the file by the
User. This can be set in the System Setup menu. If the user finds this too time consuming, this option may be
disabled. The responsibility is then on the user to SAVE THE CONFIG FILE.
The User can perform a QUICK SAVE CONFIG at any time by pressing the Save Config Button on
the Utility Setup Menu shown left.
Page 28
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.6 Sending Email
Sending email can be done in two ways – initiated by the user or initiated by an alarm condition. The email
settings have to first be set up in the System Setup menu. This is where the default recipient and routing
information is entered. To send an email on an alarm condition it is necessary to set up the alarms accordingly
shown on the left. This will bring up the email window shown below.
The data in this window has to be filled in as follows:
To: This is the recipient‟s email address.
From: This is where you enter your name or anything
you want to appear in the email “From” field.
Note: The To and From entered here override the
settings in the System Setup.
Subject: Enter text to appear in the email Subject field.
Attachment: You can attach a file to be sent along
with the email. Tap the browse icon and a file browse
window will pop up. Browse to the file you wish to
attach to the email and tap it; then tap OK. Note: More
than one file can be sent.
Tap in the text box and type any message you want.
Figure 4-6 E-mail Window
Once you have all the data entered, tap the Send button (shown left). If for some reason the email
cannot be sent, an error message will be displayed. To exit without sending the email, tap the cancel
icon [X] in the top right corner.
This space intentionally left blank.
Page 29
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.7 User Login
If password protection is enabled, the user will have to log in to be able to use many of the functions of the recorder.
There are various levels of protection and access to functions is based on user privileges. These levels are:
User: Can operate the recorder but cannot change any settings or configuration.
Manager: Can operate and configure the unit, but cannot change basic settings.
Administrator: Can operate the unit, and change all configurations and settings.
If password protection is NOT enabled then all users have administrative privileges. Log in is done
via the System Utility Menu using the log in icon shown right. This will bring up the login dialog box
shown below right.
Note: If a user is not logged in and attempts to access a
protected function, this log in dialog box will pop up at each
instance. Logging in allows a user to navigate the unit
without having to deal with this at each attempt to do
anything. Once logged in a user remains logged in until they
required to enter their password.
Enter the User ID and Password using the keyboard and
tap OK (Check mark). Check the “Change Password” box if
you wish to change your password.
To Log Out tap the Log In icon and you will be asked if you
want to log out. Tap the Yes button.
Figure 4-7 Log In
4.8 Display Utilities
The Display Utility menu allows the user to control the display brightness and background color. Enter
4.8.1 Display Brightness
The display brightness can be set at varying levels, either
continuously or can be set to dim after a preset time. Refer
to 3-11. There are two sliders – Dim Level and Normal
Level.
The Dim Level is the level the display will dim to after the
Time Out, which is selected in the dropdown box to the left
of the Dim Level slider bar. It is shown as 2 minutes in
Figure 4-8. In order for the Dim Level Time Out to be active
you need to check the Enable box. To set the Dim Level
place the stylus on the slider bar and drag the pointer or
tap the slider bar. The display brightness will alter in real
time. Select the required level.
The Normal Level setting will be the default brightness of
the display. To change the brightness, place the stylus on
the slider bar and drag the pointer or tap the slider bar. The
Figure 4-8 Display Setup
display brightness will alter in real time. Select the required level.
After the preset period of inactivity, the display will dim to the Dim Level setting. Any screen touch activity will
restore the normal level of brightness.
Page 30
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.8.2 Background Color
The background color is the default color for all screen inactive areas, (between widgets and
around the edge of the screen). It can be set by pressing the “BackGround” button shown right
and in Figure 4-8 above.
This will pop up the color selection dialog. Choose the background color required.
Tap Okay to save the settings or Cancel X to quit without saving the changes. If saved, the display will now
be at the brightness level set in the Normal Level.
4.9 Timer/Totalizer Reset
From time to time it may be necessary to reset totalizers
or timers. This is done from the System Utility menu by
pressing the Timer Reset button shown left.
This brings up the reset dialog box (shown right) which shows
all channels that are associated with timers or totalizers.
(Ineligible channels are grayed out). Check the
channels you wish to reset and press the
Reset button - The checked channels will be cleared and set
back to zero and the dialog will close. Exit the dialog at
anytime without resetting channels by pressing the Cancel
button X.
Figure 4-9 Display Setup
4.10 Special Events
There are several “Special Events” that can be programmed into the unit. These are dealt with here:
4.10.1 Record on Alarm
The recorder can be set up to record on an alarm condition. This requires setting the alarm and enabling the
record option. The Channel and Master enable boxes must be checked. The record menu must be set up to
record on alarm and the unit must be set into Record Arm mode.
The following conditions for record on alarm must be met for a recording to start.
Record Setup
Alarm Setup
Record Mode
Alarm
checkbox is checked
is checked
button has been
pressed
must be in an
alarm condition
Master and
Channel enable
must be checked
When the alarm is active the unit will start recording. It will continue to record for a minimum of 30 seconds or
until the alarm condition is removed.
4.10.2 Record on External Event
The recorder can be set up to record on an external event condition. This requires the optional Digital I/O
option and the Digital Input to be used must be set to the record option and must be enabled. The record
menu must be set up to record on external trigger and that trigger must be specified. The unit must then be
set into Record Arm mode.
Page 31
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
The following conditions for record on alarm must be met for a recording to start.
Record Setup
Digital Input Setup
Record Mode
Digital Input
External Trigger
Digital Input set to
The Record
The specified
digital input must
be activated
been pressed
The trigger source is
selected
(Must be same input
as selected in
Record Setup)
When the external event is active the unit will start recording. It will continue to record for a minimum of 30
seconds or until the external event is removed.
4.10.3 Email on Alarm Event
The recorder can be set up to send an email on an alarm event. Any alarm can be programmed to Notify a
recipient of the event. The email will be sent to the default address entered into the System Setup Menu. It is
also necessary to set up the smtp information in the System Menu. Finally, in the Alarm Setup menu the
channel must be enabled along with the Notify Enable and the Master enable.
Always make sure the email is functional by manually sending an email otherwise if the alarm triggers an
email which cannot be sent, the recorder will try then simply discard it.
The following conditions for email on Alarm event must be met for an email to be sent.
System Setup
Alarm Setup
Alarm Master Setup
Channel Enable checked
Master Enable checked
Notify Enable checked
Alarm
SMTP email
information has been
setup
Notify is checked
The specified
alarm must be in
an alarm condition
Alarm Enable is
checked
There must be a
functional Ethernet
connection
4.11 Turning the unit off
When power is removed from the unit it does not turn off immediately. There is a battery backup in the power
supply that runs the unit for a couple of minutes to ensure that all systems shut down properly and all data files
are closed and secured. Once the recorder senses the power has been removed it shuts off the display and blinks
the LED status indicator on the lower right of the front panel, to show that it is in the battery backup mode. It waits
approximately 30 seconds to ensure that the power failure is not intermittent or simply a brown out, then
commences the shut down procedure. If power should return during this period then the recorder resumes
operation normally. When the recorder completes the shutdown process, it turns the battery off and the unit is
OFF.
There are a few cautionary measures that need to be taken:
1. Ensure that the backup battery switch on the rear panel is in the ON position when using the unit and
DO NOT USE THIS SWITCH TO TURN OFF THE UNIT.
2. If the unit has been off for a lengthy period, the battery may require up to 72 hours to fully charge.
3. If you RESET the unit using the button recessed behind the media door, you may lose data if you do not
STOP RECORDING and SAVE THE CONFIGURATION FILE.
Page 32
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.12 Annotating Trends
At any time while a live trend is visible, the user may
annotate the chart by double tapping the point on the trend
at which an annotation is to be added. This will pop up a
small window as shown right which gives the option of
Browsing existing annotations
Annotating a new message
Exit and do nothing
Tap the Annotation button to get to the annotation
screen
There are two methods of annotation.
Figure 4-12.1 Live Trend
Drawing or writing on the screen and saving a
data file.
4.12.1 Drawing on the Screen
Once you tap the Annotation button the Annotate Dialog
shown right, appears.
There are several icons on the screen which function as
follows:
Tap this icon to append a text message to the
trend. This brings up the Text Memo Editor - see
Tap this icon to select the color of the pen to be
used to write on the screen. The block below the
icon shows the current pen color. (black)
Tap this Place Text icon to place the text in the
text dialog box. It is necessary to first enter text in
the box (which contains the words “JACK HIT RESET”
in Figure 4-12.2.) After tapping the icon, tap the position
on the screen where you want the text to be place. The
text is placed to the right of your tap position.
Figure 4-12.2 Annotation Screen
Save – Brings up the a dialog box which
allows the user to name the bitmap file and
save it in the record session folder (default) as a .bmp
added to the live trend.
Cancel – Quits the annotate session and
returns to the live display.
Print – Allows the user to print to the system
printer, if installed.
Clear – Removes all annotation from the
Figure 4-12.3 Place Text
Page 33
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
screen
To draw on the screen, select the pen color as detailed above then, using the stylus, draw on the screen. Add
any text in the text box and place it on the screen using the place text icon as detailed above. This allows the
user to annotate clearly and precisely on the screen (see Figure 4-12.3 above) and save the picture
accordingly. An indication on the live trend
indicates that a bitmap has been saved.
4.12.2 Adding a Text Message
Enter the Text Message Editor by tapping the icon
Text Message Editor is shown in Figure 4-12.4. Any
message can be entered in the text box as shown.
Once the message has been entered it can be placed
using the Attach button.
Attach button - embed text in the file.
Cancel button - abort the operation.
Clear button – clear current text.
Figure 4-12.4 Text Message Editor
An indication on the live trend
message has been saved.
indicates that a text
4.13 Browsing Historic Data
It is possible to browse through historic data that
may no longer be visible on the live trend. To do
this you need to tap the browse button (left) on the bottom
right of the live trend display as shown on the right.
This will bring up the Browse Display window (See Figure 4-
13.2), which essentially freezes the current display (live data
is still updating in the background) and retrieves data from a
buffer holding the historic data through the time the browse
button was tapped. Note the “envelope” icon on the trend
indicating an embedded memo or bitmap file.
Tap this
Figure 4-13.1 Live Trend
On the Browse Display it is possible to limit the number of
traces on the display or add markers to easily identify points
on the traces. The Browse Display will open and show the last
current data. Use the slider bar to navigate back through
historic data. Data can be expanded or contracted using the
Zoom % drop down menu and the user can jump to memos,
specific times and max or min values.
The controls available are as follows:
Markers On – The trace is actually made up of
distinct points with an interpolated line between them.
Tapping this icon will place markers on the actual points on the
trace. This helps identify the actual data points on the trend.
Figure 4-13.2 Browse Display
Page 34
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
Markers Off – Tapping this icon will remove the
markers from the traces. This icon will only be visible
if the markers are currently on.
Cursor – Tapping this icon turns on the cursor which
allows unique identification of the points.
Go – Proceed to the (next) instance of the „jump to”
drop down dialog (memo in Figure 4-13.3). Jump
options are memo, time, Ymax and Y min. See
Go from Start – Start at the beginning of data (most
recent) and proceed to the next instance of the „jump
to” drop down dialog (memo in Figure 4-13.3)
Trace Setup – Tapping this icon will bring up the
Trace Setup screen (see Figure 4-13.3), which
Figure 4-13.3 Trace Setup
enables the user to shut off traces on the display. Those
traces not on the original trend will be grayed out. Check the box next to the trace you want displayed, uncheck it
to remove the trace from the browse trend. Traces can be turned on or off at any time.
Slider Bar – The Slider Bar is used to scroll back and forth through the data buffer. Sliding to the left brings up
older data, sliding to the right brings up newer data. To move, press the slider with the
stylus (or finger) and drag, or tap the bar to the left or right of the slider.
Exit - Returns to live data.
Note: The browser will always be in the form of a horizontal trend even if the live trend is vertical.
When in the browser, double-tapping the trend display area will take you to the Annotate Dialog window. Here the
user can markup the current view and save it or print it. This permits annotating historic data which may have
been missed on the live trend.
4.13.1 Zoom and Compress Data
Using the Zoom % drop down menu the user can select to zoom (numbers > 100) or compress
(numbers <100) the time axis of data on the screen. Simply select the zoom value and the trend
display will recalculate and display the compressed or zoomed data. 100% Zoom is the normal
representation on the trend. It may take some time to recalculate the view depending on the zoom level.
Figure 4-13.4 below, shows data zoomed 5 times with the point markers turned on. Figure 4-13.5 shows data
compressed 5 times without point markers. The slider bar will navigate through the data at the zoom level
selected.
Figure 4-13.5 Compress no point markers.
Figure 4-13.4 Zoom with point markers
Page 35
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.13.2 View Memos and Bitmaps
At any time in the browse window, when an embedded memo or bitmap flag
is visible, the respective
memo or bitmap can be viewed by tapping the envelope icon ONCE. Note that double tapping the screen will
The text memos will show in a pop up window on the trend browse screen as shown in Figure 4-13.6 below.
The bitmaps will show in a new window, provided the bitmap is available – see Figure 4-13.7. If you removed,
renamed or deleted the .bmp file, you will get an error message. When you are done viewing the memo, tap
the “OK” button. On the bitmap tap the check mark (Done) button. If the memo or bitmap was attached while
recording a file, these items will be available for review on the PC software.
Fig 4-13.7 Bitmap View
Fig 4-13.6 Memo View
4.13.3 Using the Cursor
the cursor button will bring up a cursor on the
browse screen. A window will pop up on the right
hand side of the screen showing the time and active
channel values directly under the cursor.
The upper slider bar scrolls through the data buffer.
The lower slider bar moves the cursor.
Fig 4-13.8 Cursor Mode
Page 36
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4 – Functional Description
4.13.4 Using Browser Jump To
Future feature.
4.14 Browsing Annotations
It is possible to view attached messages and bitmaps
directly from the live trend window by double tapping
anywhere on the trend.
This
will
bring
up
the
Browse/Annotate selection box
(shown left). The drop down
menu shows the times of all
attached memos or bitmaps in
the buffer with the latest one first. Select the time of the
attachment you wish to view then press the attachment
(envelope) button..
The memo or bitmap will be displayed as shown in View
Memos above
Figure 3-14.1 Live Trend
Page 37
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.0 RECORDER SETUP
The recorder can be fully customized and needs to be set up by the user. The setup is saved in configuration
files, which can be saved and loaded by the user. Several configurations are shipped with the unit and can be
used as a starting point or the user can start with a clean slate and create a unique configuration.
5.1 Input Channels
The recorder has 18 channels that need to be configured and set up. The setup for the channels requires defining
the inputs. Channels 1 to 12 (channels 7 to 12 are optional) can be live inputs – analog or digital. Channels 13 to
18 or any other channel not assigned to a live input can be a virtual channel. Unused channels should be set as
unassigned. The channels can be:
Analog:
Digital:
Linear – Voltage or Currents, Resistance, Thermocouples, RTD‟s
Square Root Extraction - Voltage or Currents
Logic input (Dry Contacts).
Frequency Input. Channels 1,6,( optionally 7,12) can accept frequency inputs (Frequency,
Period, Count, Pulse Width, Duty Cycle)
Virtual:
All channels not assigned above can be Computational, Conditional, Gated Timers or
Totalizer channels. Although not directly linked to live inputs, these channels can be indirectly
associated with live inputs through the computational and conditional options.
5.1.1 Master Channel Setup
The Master Channel Setup window is a one stop
shop to quickly set up all the channels or get a
general overview of channel setup. If passwords
are enabled the user has to log in as Administrator
in order to access. NOTE: You cannot use this
option if the unit is in the record mode – you need to
stop the recording first (See Section Record Setup).
To access the Master Channel Setup window:
Press the Utility Setup Menu icon on the
bottom left of the Task Bar.
Then press the Master Channel Setup
icon.
Figure 5-1 Master Channel Setup
NOTE: It takes the recorder a while to build the
setup display as shown right.
The Master Channel Setup dialog window shows the current setup of all the channels and allows the user to
edit each of them individually. The checkboxes show whether the channel and its alarms are enabled.
You can see the current settings for Input Type, Range and Engineering Units. For example in Figure 5-1,
Channel 2 is set up as a Gated Timer with engineering units of Seconds. The channel is enabled and the
alarms are disabled.
Tap the double arrow button to view the other 12 channels. In order to change the setups it is
setup menu. When you have completed the channel setups press the done button to return.
Page 38
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.1.2 Channel Setup
Pressing the edit button from the Master Channel Setup window takes you to the Channel Setup dialog
window as shown in Figure 5-2. The user can copy an existing channel to this one or set up a new channel
including the channel type and range, the point tag, engineering units and assign colors. Values set here will
be the default for any widget attached to this channel.
Channel: Use this pull down item to select the
channel to be edited.
Enable Checkbox: Use this to enable or disable
the selected channel.
Alarms Enable Checkbox: Use this to enable or
disable alarms for this channel.
(Alarms) Setup: Used to set up the
alarms for the selected channel. See
Alarm Setup for detail
Copy From: Choose a channel from the pull down
item list to copy all its setup parameters to the
current channel set up.
Channel Type: Choose the channel type from the
pull down item list. Further setup is required. See
Figure 5-2 Channel Setup
Point Tag: Enter up to nine alphanumeric characters to uniquely identify the channel. Up to 8 characters can
be entered.
Eng units: Enter up to eight alphanumeric characters to indicate the engineering units for the channel. Up to
7 characters can be entered. Note: Setting up the channel will default to engineering units for the type
selected.
Dec Pt.: Decimal Points – Select number of places after the decimal point to display.
Scale: This is used to customize the scale on trends and bar charts to something other than the default. For
example in Figure 5-2 above, the Linear 12 volt range has been selected. The scales will default to 0, 6, 12 as
shown. If the input range of interest were 5 to 10 volts you could set the low, mid and high scales to 5, 7.5 and
10 respectively.
Colors: Use this to set up the channel colors for the digits, bar and trend in the widgets. See
Widgets for more detail
BackGround: Use this button to set up the channel background colors for the bar and digit
widgets.
Apply: Save these changes and exit.
Cancel: Exit without saving the changes.
Page 39
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.1.3 Channel Type Setup
The Channel Type Setup dialog window is dependent upon the type of input selected in the Channel Setup
window above.
5.1.3.1 Linear Input
For Linear Voltage and Current the dialog box is
shown in right. For other input types it will differ.
Select the Type from the pull down item list. The
following ranges are available.
Voltage: + 125mV, 250mV, 500mV, 1V, 3V, 6V, 12V
and 24V full scale.
Current: 4-20mA, 0-20mA and 10-50mA. NOTE :
When selecting currents it is necessary to provide a
terminating resistor of 50 ohms at 0.1% across the
terminal inputs.
Figure 5-3 Linear Input Setup
Dry Contacts: This option is for use with potential
free contacts - used for logic inputs. Display will show OPEN or CLOSED accordingly.
Input/Output Ranges: Figure 5-3 shows the +1.0 Volt input range for the analog input. The Input and
Output ranges LOW and HIGH values set the scaling for the channel. They default to the zero and high
values for the range so that the channel reads the full scale range. As shown when the input is zero the
output will read zero, and when the input is 1 volt the output will read 1. If the Output - HIGH was set to
100 then the output would be 0 to 100 for an input of 0 to 1V. The input is effectively multiplied by the
(Output High)/(Input High).
Span: The span is a correction value that is multiplied by the full scale input and applied linearly across
the range. The default is 1.
Offset: The offset is an adder (subtractor) that is added or subtracted to the output. Thus in the equation
y = ax + b, y is the final output, x is the input value, a is the span multiplier and b is the offset. The default
is 0.
Filter: The filter is applied to the inputs when the Enable check box is checked. The filter performs a
running average of n samples, where n is the numeric value set in the AVG box from 1 to 100.
Calculator: This will bring up a simple calculator that allows the user to do computations to
calculate the scaling factors if needed.
Apply: Save the values and exit
Cancel: Exit without making any changes.
5.1.3.2 Resistance Input
The Resistance setup dialog window is similar to that in Figure 5-3 above. Resistance measurement uses
a constant current source through the load, measures the voltage and computes:
Resistance = Current x Voltage.
There are three resistance ranges which are selected via the pull down menu.
Resistance Ranges: 100 ohm, 500 ohm and 5000 ohm
Page 40
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
The resistor (or load) is connected like a 3 wire RTD – See Section 3.0 Installation. Use the Output Low
and High to scale the resistance to the engineering unit of choice.
5.1.3.3 Industrial Square Root Extraction
The recorder accepts the same input types for Industrial Square Root as it does for Linear with the
exception of Dry Contacts. This function is used for inputs which require the Square Root of the input
signal (i.e. flow measurement). The system calculates the square root of the percentage of input scale
and multiplies this value by the high-end scale to produce the value of the point displayed.
In the following example, the input is 4 to 20mA and the scaling is such that 0 = Low End of Scale and
1000 = High End of Scale which represents 1000 gallons per minute.
Let the input Signal = 12mA or 50% of scale which is equal to 0.5
Square Root of 0.5 = 0.707
Actual value displayed is 0.707 x 1000 = 707 GPM (with Decimal fix of 0)
The setup is the same as it is for the Linear input in Section 5.1.3.1.
5.1.3.4 Thermocouples and RTDs
Thermocouple and RTD setup is similar to the
Linear setup except that the Input and Output
scaling cannot be altered. Note that the displayed
scales can be set independently for each widget
– See Widgets for more detail.
Select the Thermocouple (RTD) type from the
drop down menu. The default Engineering Units
is Degrees F. To select Degrees C check the
degC check box.
Thermocouple inputs reference the ambient
temperature compensator on the rear of the unit.
To disable this, uncheck the Use Tcomp
checkbox. The unit will display uncompensated
Thermocouple values.
Figure 5-4 Thermocouple Setup
Apply Span and Offset as needed and select Filter type as detailed in Section 5.1.3.1. above.
Note: For thermocouples, the ambient temperature compensation can be adjusted in 0.5° increments in
the Temperature Compensation menu of the Admin Setup Menu.
Page 41
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.1.3.5 Calculated Input
Any of the eighteen channels can be a calculated channel. A calculated channel gets its value from a
series of calculations, which may be based on one or more live channels. Setting a live input channel to
be a calculated channel will disable the live input. It is recommended that the virtual channels (Channel 7
to 18 in a 6 input unit or Channels 13 to 18 in a 12 channel unit) be assigned as calculated channels.
The Calculated Channel Setup dialog window has some powerful options. The user can set up 6
constants (X,Y,Z,I,J,K) to be used in the calculation and can define up to 6 functions (F1 to F6). The
calculation can contain live inputs (C01 to C06 – Channels 1 to 6 for a 6 channel unit, or C01 to C12 –
Channels 1 to 12 for a 12 channel unit), or other defined channels C01 to C18. The icons are defined as
Delete Button
Test Button
Clear Button
Exit Button
Constants: This allows the user to set a
constant value, eg 3.41592 to a variable, say X,
then use this in an equation by simply selecting
the X. This is useful for coefficients and the like.
To set the constant, check the Set Const. box,
then touch any of the entry boxes to the right of
the constant buttons. Use the numeric keys to
enter the value. The ◄ and ► buttons will move
the cursor, the Del button will delete the
character to the left of the cursor and Clear
button will erase all digits. When complete
UNCHECK the Set Const. box. You can now use
the constants by simply selecting the button. In
the example shown right, pressing the X button
will insert X into the equation, which is equivalent
to 3.41592.
Figure 5-5 Calculated Channel Setup
Functions: This allows the user to define up to six functions for use in the calculations. To set up a
function, check the Define box, then press the Function button, say F1. The input line will show F1=,
continue to enter your formula using the available buttons. The ◄ and ► buttons will move the cursor, the
Delete button will delete the character to the left of the cursor and Clear button will erase all digits. Once
you have entered the function press the Enter button. (The Test button will change to Enter when you
first select a Function key.) When you are done UNCHECK the Define box. You can now test your
function or use it in the calculated channel.
Calculations: The calculations entered here will be assigned to the channel being set up. The
calculations can use any of the 18 channels (C01 to C18), any of the six functions, any of the six
constants, and the math functions. Make use of the parenthesis buttons to ensure your formula is
interpreted correctly. The ◄ and ► buttons will move the cursor, the Del button will delete the character
to the left of the cursor and Clear button will erase all digits. Once complete, it is necessary to test the
function for accuracy by pushing the Test button. This will bring up the Test dialog as shown below. Once
the calculation has been fully tested, press the Done button to return to the Calculated Channel Setup
window and then press the Exit button.
Min, Max, Avg: The functions Min, Max and Avg use the MINimum, MAXimum or AVeraGe of a channel
input in the calculation. The Average is a weighted average = (last value + current value)/2. The format is
MAX(C02)+MIN(C03) for the maximum value of channel 2 plus the minimum value of channel 3. If Min,
Max or Avg is used in an equation a reset dialog will appear upon exit. See below.
Page 42
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Test Dialog: This window enables you to test your
calculation after the recorder has compiled it. The
original calculation is shown in the top line. There
are entry boxes to enable you to set actual values for
the channel variables. Once you have entered data,
pressing the Calculate
button will display the
answer in the line above it. This test dialog
can also be used to evaluate functions or
any other expression entered.
If the answer is as expected or you need to go back
and alter the formula press the Exit button.
Figure 5-6 Test Dialog Window
MIN MAX AVG RESET: If the Min, Max or Avg
function is used in an equation, upon exit you will
get the Min, Max, Avg Reset Dialog window shown
right. This enables the Min, Max or Avg values to
be reset periodically, upon an external event or
upon an alarm event.
Auto Reset Enable: If this box is unchecked the
Min, Max, Avg will calculate continuously unless
External Reset Enable is checked. If the Auto
Reset Enable box is checked then the values will
reset at the Reset Interval.
Ext. Reset Enable: This is the External Reset
enable. If this box is checked the max, min, avg
values will be reset by an external event via the
digital inputs Note: an optional digital I/O card must
be present in the system AND the designated input
Figure 5-7 Min Max Avg Reset Setup
must be input is enabled. The digital input needs to be programmed as a MinMaxAvg type.
Reset Intrvl: This is the Reset Interval. This is the time in days, hours, minutes and seconds between
timer resets when Auto Reset is checked. In the example th min, max oravg will be reset every 5 minutes.
Reset Sync: If the Sync Enabled checkbox the max, min or avg will reset the first time it reaches the
set time. This allows the user to synchronize the reset to a known time. This also allows several channels
to be synchronized together if the Reset Sync time is set to the same for all. This time is ignored if the
enable box is not checked.
Reset Print: When this box is checked the max, min avg reset information will be appended to the
alarm/event log each time the values reset.
Power Up Reset: When this box is checked the value (max, min or avg) will be reset on power up,
otherwise it will continue from the last value saved before power down.
Reset on Alarm – If Alm Reset Enable is checked the Min, Max,
Avg values will be reset by the Alarm condition selected. In this
case when Channel 1 Alarm 1 is active.
Page 43
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.1.3.6 Conditional Input
Any of the eighteen channels can be a
conditional channel. A conditional channel gets
its value from a true or false test of conditions
which may be based on a live channel. Setting
a live input channel to be a conditional channel
will disable the live input. It is recommended
that the virtual channels (Channel 7 to 18 in a 6
input unit or Channels 13 to 18 in a 12 channel
unit) be assigned as conditional channels.
Basically the user sets up a condition which
can have two possible outcomes, one if the
condition is true and another if the condition is
false.
The Conditional Channel Setup dialog window
requires three inputs: the condition to be
tested, the result if true, and the result if false.
See Figure 5-8.
Figure 5-8 Conditional Channel Setup
C01 through C18 represent channels 1 to 18, some of which may be live channels. The Conditional
Channel Setup window also allows up to six constants to be set and used. See constants above.
pressing the Exit button. In the example of Figure 5-8, Channel 13 is being programmed to indicate zero
to 100 for a 4 – 20 milliamp input on Channel 1 with any input less than 4 milliamps showing zero.
5.1.3.7 Gated Timer
The Gated timer Calculated point type allows a
timer (measuring in seconds) to be controlled by a
„gate‟ from a logic point. For example, if a point is
measuring temperature and you wanted to know
the total amount of time the temperature measured
by this point is above or below a certain level, a
Conditional point can be programmed to be TRUE
only when the temperature is above or below a set
level. A Gated timer point can then be programmed
to be turned ON only when the Conditional point is
in the TRUE state. The Gated timer point will then
only be timing when the temperature is above or
below a set level. The timer will continue to
accumulate time (in seconds) each time it is turned
on. The Gated timer point can be reset at
programmable time intervals and alarms can be
Figure 5-9 Gated Timer Setup
set to alarm if the timer total goes above a
programmed time interval in seconds.
The Gated Timer Setup dialog window is shown in above right. There are several options:
Auto Reset: If this box is unchecked the Timer will run continuously unless External Reset is enabled. If
the Auto Reset box is checked then the timer will reset at the reset interval.
Page 44
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Ext. Reset Enable: This is the External Reset. If this box is checked the timer will be reset by an external
event via the digital inputs Note: an optional digital I/O card must be present in the system AND the
designated input must be programmed as a timer reset for this to work.
Ext Reset Point: This indicates which external digital input will reset the Timer when Ext. Reset Enable
above is checked and the digital input is enabled. The digital input needs to be programmed as a Timer
Reset type.
Reset Intrvl: This is the Reset Interval. This is the time in days, hours, minutes and seconds between
timer resets when Auto Reset is checked.
Reset Sync: If the Sync Enabled checkbox the Timer will reset the first time it reaches the set time.
This allows the user to synchronize the reset to a known time. This also allows several channels to be
synchronized together if the Reset Sync time is set to the same for all. This time is ignored if the enable
box is not checked.
Base Point: This is the actual source for the timer control. The channel selected from the drop down
menu should be set up for the correct input and in the correct units. If the timer is to free run DO NOT
select any Base Point
Reset Print: When this box is checked the timer reset information will be appended to the alarm/event
log each time the timer resets.
Power Up Reset: When this box is checked the Totalizer will start from zero each time the unit powers
up, otherwise it will carry on where it left of before.
5.1.3.8 Totalizer
The Totalize calculation keeps a running total of the value of a (base) point sampled at a programmed
rate. This will continue until the programmed reset interval time is reached at which time the value is
logged on the Alarm/Event log window (if Reset Print is enabled), is reset to zero, and the totalization
calculation begins again. However, a Low flow cutoff provision prevents totalization on flow rates that
meet or fall below the cutoff point. The data will also be recorded to disk if Alarm/Event logging is
enabled. The Totals are non-volatile unless the Auto reset option is active.
The Totalize Setup dialog window is shown
right. There are several options:
Auto Reset: If this box is unchecked the
Totalizer will run continuously unless External
Reset is enabled. If the Auto Reset box is
checked then the totals will reset at the reset
interval once the start time has been met.
Ext. Reset Enable: This is the External Reset.
If this box is checked the total will be reset by an
external event via the digital inputs Note: an
optional digital I/O card must be present in the
system AND the designated input must be
programmed as a totalizer reset for this to work.
Reset Point: This indicates which external
Figure 5-10 Totalizer Setup
digital input will reset the Totalizer when Ext.
programmed as a Totalizer Reset type.
Page 45
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Reset Intrvl: This is the Reset Interval. This is the time in days, hours, minutes and seconds between
total resets when Auto Reset is checked. The example above will reset the Total every 5 minutes.
Reset Sync: If the Sync Enabled checkbox is checked the
Total will reset the first time it reaches the set time. This
allows the user to synchronize the reset to a known time. This also allows several channels to be
synchronized together if the Reset Sync time is set to the same for all. This time is ignored if the enable
box is not checked.
Reset Print: When this box is checked each time the total is reset, the information will be
appended to the alarm/event log (time and total).
Flow Rate /: The Flow Rate will be displayed per second, minute, hour or day
depending what is selected in this drop down menu.
Cut Off Level: This is the low flow cut off. If the input value of the base point is
less than or equal to this value, it will not be totaled. Thus here if the input falls
below 15 liters/minute the flow total will not update.
Base Point: This is the actual source for the totalization. The channel selected
from the drop down menu should be set up for the correct input and in the correct
units.
Total Reset on Alarm – If checked the Total will be reset by the Alarm
condition selected. In this case when Channel 1 Alarm 1 is active, the
Total will be reset.
5.1.3.9 Frequency/Pulse Count
Channels 1, 6, 7 and 12 can be used to measure
frequency. Frequency is applied to a separate
isolated input. Inputs are TTL compatible and can
take signals up to 12 volts. There are two options for
frequency that can be selected: Frequency – which
measure actual frequency in Hz and may be scaled
accordingly. Pulse Count – which counts pulse
transitions on the inputs and may be scaled
accordingly. In addition alarm and reset features can
be applied.
5.1.3.9.1 Frequency
Figure 5-11 Frequency Select
Select Frequency from the setup menu. The Input
High and Low and Output High and Low can be
used to scale the frequency. For example: to have
the readings be in revolutions per minute (RPM) set
the input to 0 and 1000 for low and high respectively
and the output to 0 and 60000.
Neg. Edge Trigger: Checking this box will cause
frequency to be measured on the Negative Edge of
the input waveform as opposed to the default
positive edge.
Filter: The filter is applied to the inputs when the
Enable check box is checked. The filter performs a
running average of n samples, where n is the
numeric value set in the AVG box from 1 to 100.
Figure 5-12 Frequency Setup
Page 46
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Calculator: This will bring up a calculator that allows computations to calculate the scaling
factors.
Apply: Save the values and exit
Cancel: Exit without making any changes
5.1.3.9.2 Pulse Count
Select Pulse Count from the setup menu. The
options for Input and Output scaling and Negative
Edge Triggering are as above. There is an
additional setup setting indicated by the setup
icon.
the
Pressing this button will bring up
Reset Options for the Pulse
Count.
The Pulse Count keeps a running total until a
reset event occurs. This can be a programmed
reset interval time, external reset or alarm reset.
At this point the count total is logged in the
Alarm/Event log window (if Reset Print is
enabled) and the count is reset to zero, begins
again. The data will also be recorded to disk if
Alarm/Event logging is enabled. The count total is
non-volatile unless the Auto reset option is active.
The Pulse Count Reset dialog window is shown
in Figure 5-14. There are several options:
Figure 5-13 Pulse Count Setup
Auto Reset: If this box is unchecked the Count
will run continuously unless External Reset is
enabled. If the Auto Reset box is checked then
the totals will reset at the reset interval once the
start time (Reset Sync) has been met.
Ext. Reset Enable: This is the External Reset. If
this box is checked the count will be reset by an
external event via the digital inputs Note: an
optional digital I/O card must be present in the
system AND the designated input must be
programmed as a count reset for this to work.
Reset Point: This indicates which external digital
input will reset the Totalizer when Ext. Reset
Figure 5-14 Pulse Count Reset Setup
Enable above is checked and the digital input is enabled. The digital input needs to be programmed as
a Count Reset type.
Reset Intrvl: This is the Reset Interval. This is the time in days, hours, minutes and seconds between
total resets when Auto Reset is checked. The example above will reset the Total every 5 minutes.
Reset Sync: If the Sync Enabled checkbox is checked the
Count will reset the first time it reaches the set time. This
allows the user to synchronize the reset to a known time. This also allows several channels to be
synchronized together if the Reset Sync time is set to the same for all. This time is ignored if the enable
box is not checked.
Page 47
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Reset Print: When this box is checked each time the total is reset, the information will be
appended to the alarm/event log (time and total).
Total Reset on Alarm: – If checked the Total will be reset by the
Alarm condition selected. In this case when Channel 1 Alarm 1 is
active, the Total will be reset.
Apply: Save the values and exit
Cancel: Exit without making any changes
Page 48
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.2 Display Builder
The Display Builder allows the user to customize the
Graphical User Interface (GUI) or display screen using
widgets to display data in various ways. The standard
display on the recorder is shown on the right and
consists of the Task Bar at the bottom of the screen and
a display showing live or calculated data from various
sources. In this case the display is a combination of
vertical bar graphs, digital displays and a trend. These
are the widgets and each can be customized as
required either during setup or by double-tapping the
widget.
The user can create numerous displays with any
combination of widgets that will fit the screen. Each
display can be named and saved, and the user can
List for viewing purposes. The displays are created in
Figure 5-2-1 Standard Display
5.2.1 Building the Display
To build a display:
Press the Utility Setup Menu icon on the bottom left of the Task Bar (shown left). Then
press the Display Builder icon to launch the Display Builder dialog window. (shown right).
The Display Builder consists of a palette on which the user can place widgets to create a display. The palette
is a grid of blocks 6 across by 8 down. Each widget is a finite size consisting of 2 or more blocks – see below
for details. The buttons to the right allow the user to select the widget types while the drop down selection box
below defines the size and style of the widget type selected. Button functions are as follows:
The user can load an existing display to modify or
start with a clean palette. To do this press the Load
button and a window will pop up as shown in Figure
5-2-2. Browse for a display name or enter it in the
space provided and press Apply. See below for
Editing options.
Starting with a clean page, widgets (bars, Digital
windows, Trends) need to be placed.
To place a widget, select one of the buttons to the
right. Once a button is selected it is necessary to
select the widget size and style from the drop down
selector. Once selected, the user can continue to
place this style of widget by tapping a block in the
grid until there is no space left or an alternate widget
style is selected. Widget sizes relate to grid blocks.
Figure 5-2-2 Display Builder, Load Display
Page 49
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Widgets are selected as follows:
Place Digital display either full size (2x2) or half size (2x1).
Place Bar Graphs - horizontal full (6x1) or half (3x1) or vertical full (1x8) or half (1x4).
Place Trends - horizontal full (6x8), two-thirds (4x8) or half (3x8) and vertical full (6x8) or half
(6x4).
Place graphics or set background colors
When placing a widget the system will attempt to put it at the block you tap if space is available. It will move it
to fit, otherwise you will get an error tone and nothing will be placed.
As widgets are placed on the palette they need to be defined. They have to be associated with a channel,
have colors defined, and have scales set where necessary. This can be done as the widget is placed or can
be edited using the Edit buttons. For details on configuring the widgets see the setup information for Digital
Display, Bar Charts or Trends below.
Widgets already placed can be moved or deleted. The display can be named or renamed and saved and the
whole process can be aborted by pressing the Cancel button.
5.2.2 Editing
Once widgets are placed the following buttons can be used to edit the display:
Delete: Will delete a widget. Press the
Delete button then tap the widget you want
to delete.
Edit: Allows a widget to be edited. Press the
Edit button then tap the widget you want to
Move: Allows a widget to be moved. Press
the Move button then tap the widget. It will
be “lifted” off the palette. Tap the new location you want
to move the widget to.
Clear All: Will completely clear the palette
of all widgets.
Save: Saves the display with the name
entered into the save dialog box.
Alternatively, select an existing display name and
overwrite it.
Figure 5-2-3 Display Builder
Load: Loads an existing display which can be modified. Use the dialog box to select existing
displays.
Cancel: Discard all settings and exit.
Exit: Exit with settings intact.
Page 50
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.2.3 Rotate List
The Rotate List allows the user to decide which
display views will be active. Under normal viewing
conditions, the user can rotate through the displays
by pressing anywhere on the Task Bar where there is
no button. Each time the Task Bar is pressed the
next display will be loaded.
The Rotate List Setup dialog window as shown right
allows the user to select which displays will be active
and set the order in which they display.
To access the Rotate List Setup dialog window:
Press the Utility Setup Menu icon on the
bottom left of the Task Bar.
Then press the Rotate List icon to launch
the Rotate List dialog window as shown
in Figure 5-2-4.
Figure 5-2-4 Rotate List Setup
The Rotate List Setup dialog window has two columns: the Rotate List column contains the active displays
that will be viewed; the Displays column contains all the current displays in the system.
The display view at the top of the Rotate List (Test in the example) is the default display that will show when
the unit is powered up. Subsequent displays in the list will show each time the Task Bar is pressed, in the
order listed.
To remove all displays from the Rotate List press the Double Right arrow button.
To remove a display from the Rotate List, highlight it then press the Right arrow button.
To add a display to the Rotate List, highlight it in the Displays column and press the Left arrow
button.
To change the order in the Rotate List, highlight a display name by tapping it then use the up arrow
button to move that display upwards.
To DELETE a display in the Displays column, highlight it by tapping the display name; then press
the Delete button. Note: Once a display is deleted there is no way to recover it.
Auto Rotate: If this box is checked then the displays will automatically rotate in the order listed in the Rotate
List from top to bottom. Each display will remain for 30 seconds before the next one shows.
To exit without changing anything, press the Cancel button (X). To exit and keep any changes, press the
Accept button (). Upon exit the unit has to rebuild the display list. The status of the rebuild is indicated
below the Delete button.
Page 51
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.3 Widgets
A widget is a graphic element that a user interacts with or is used to build graphical user interfaces or GUIs. In the
case of the recorder, the user constructs a GUI using the Display Builder using widgets. There are two basic
types of widgets – Bars and Digital Displays. Trends, while treated as a widget in the Display Builder, are an
5.3.1 Digital Displays
There are two types of digital displays: full size and half size. Up to 12 full size and 24 half size digital displays
can be placed on the GUI.
The half size digital display widget is 2 blocks across by 1 block tall. It shows the Point
Tag – up to 8 characters and the Engineering Units up to 7 characters. It can display up
to 10 digits of data.
The full size digital display widget is 2 blocks across by 2 blocks tall. It shows the
Channel Tag – up to 8 characters and the Engineering Units up to 7 characters. It can
display up to six large digits or eight smaller digits of data.
5.3.1.1 Digital Display Setup
The Digital Display Edit dialog window will pop up when setting up a display using the Display Builder or
can be invoked at any time by double-tapping
the Digital Display widget on the screen.
The dialog box shows the Channel Number (2)
and the Channel Type (Digital Readout). The
user can use this dialog to change appearance
parameters of the Digital Display Widget or
can proceed beyond to fully set up or edit the
channel information.
Channel: Shows the current Channel assigned
to the widget. The user can change the
assignment by selecting a different channel from
the drop down list.
Channel type: Shows the current widget style
for the channel. For information only.
Enable: When checked the Digital Display is
active, when unchecked it is off and the Display
will show OFF.
Figure 5-3-1 Digital Display Edit
Point Tag: This is a description for the channel point and defaults to the Channel Setup value. It can be
changed for this Digital Display. User can enter up to 8 characters
Eng Units: This is the Engineering Units for the channel and defaults to the Channel Setup value. It can
be changed for this Digital Display. User can enter up to 8 characters
Color: Used to set the color of the DIGITS in the Digital Display Widget and defaults to the
Channel Setup value. It can be changed for this Digital Display.
BackGround Color: Used to set the Background color for the Digital Display Widget and
defaults to the Channel Setup value. It can be changed for this Digital Display.
Dec Pt.: Decimal Points – Select number of places after the decimal point to display on the Digital
Display Widget.
Page 52
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Alarms: When the Active box is checked the alarms are active for this channel (2) provided the Master
Enable is set. When not checked the alarms are deactivated for this channel. Pressing the Alarms button
which will affect ALL widgets using this channel. This is a protected option.
Apply: Pressing this button will exit and save any changes made.
Exit: Pressing this button will exit without saving any changes made in THIS dialog box ONLY. If you
used the Setup or Alarms buttons to make changes to the channel information, these are Global and
WILL be saved.
made to the channel settings which will affect ALL widgets using this channel. This is a
protected option.
Delete: Pressing this button will DELETE the Digital Display Widget. This will remove it from
the display.
5.3.1.2 Displaying Min, Max or Average Values
The Digital Display widgets show the instantaneous channel value but can be
changed at any time to display minimum, maximum or average values. To
change the reading double tap in the lower line of the digital display widget
indicated right.
This will pop up a drop down menu that allows the user to select the display
mode as follows.
INST. =
Instantaneous – display the data as it is read – default (real time
display)
MIN.
Minimum - will display the minimum (lowest) value ever measured.
MAX. Maximum – will display the maximum (highest) value ever measured
AVG. Average – will perform a weighted average on all input samples at 10
samples/sec and average them as (last value + current value)/2 and display this.
The display indicated the current display mode in the lower left of the display
widget using the characters above -
with the exception that NO indicator
is shown for real time (instantaneous) value. Maximum value is shown displayed
right.
Page 53
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.3.2 Bar Graphs
There are four types of bar graph widgets, two horizontal and two vertical with full size and half size versions
of each. Up to 8 full size horizontal and 16 half size horizontal bar graphs can be placed on the GUI. Up to 6
full size vertical and 12 half size vertical bar graphs can be placed on the GUI.
The full size
vertical bar
The half size
vertical bar
widget is 1 block
across by 8
widget is 1 block
across by 4
The full size horizontal bar widget is 6 blocks
across by 1 block tall. It shows up to 8 characters
of Channel Tag and Engineering units. It has a 5
character Digital readout
blocks tall. It
shows up to 8
characters of
Channel Tag
and Engineering
units. It has a 5
character Digital
readout
blocks tall. It
shows up to 8
characters of
Channel Tag and
Engineering
units. It has a 5
character Digital
readout
The full size horizontal bar widget is 3 blocks
across by 1 block tall. It shows up to 8 characters
of Channel Tag and Engineering units. It has no
Digital readout
5.3.2.1 Bar Graph Setup
The Bar Graph Display Edit dialog window will pop up
be invoked at any time by double-tapping the scale on the
bar graph widget on the screen.
The dialog box shows the Channel Number (2) and the
Channel Type (Horizontal BAR Full). The user can use
this window to change appearance parameters of the Bar
Graph widget or can proceed beyond to fully set up or edit
the channel information.
Channel: Shows the current Channel assigned to the
widget. The user can change the assignment by selecting
a different channel from the drop down list.
Figure 5-3-2 Bar Graph Display Edit
Channel Type: Shows the current widget style for the
channel. For information only.
Enable: When checked the Bar Graph is active, when unchecked it is off and the Display will show OFF.
Point Tag: This is a description for the channel point and defaults to the Channel Setup value. It can be
changed for this Bar Graph. User can enter up to 8 characters
Eng Units: This is the Engineering Units for the channel and defaults to the Channel Setup value. It can
be changed for this Bar Graph. User can enter up to 7 characters
Color: Used to set the color of the BAR in the Bar Graph widget and defaults to the Channel
Setup value. It can be changed for this Bar Graph.
BackGround Color: Used to set the Background color for the Bar Chart and defaults to the
Channel Setup value. It can be changed for this Bar Graph.
Dec Pt.: Decimal Points – Select number of places after the decimal point to display on the Bar Graph
widget.
Page 54
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Scale: This is used to customize the local scale on the Bar Chart widget. In the above example, the input
is a J Type Thermocouple which has an actual scale of -346 to 2192 °F. For this bar chart it has been set
to 0 to 150 to show more detail at the points of interest. It can be changed at any time and only affects
this widget.
Use Chan: This button will fetch the original scale values from the Channel Setup information and insert it
in the scale information. In the above example it will populate the scale with original thermocouple values.
Once scales are set they remain constants with the widget. Any change to the channel will not update the
scales (It will update everything else). The user can update the scales on this widget with this Use
Chan(nel) button.
Alarms: When the Active box is checked the alarms are active for this Channel (2) provided the Master
Enable is set, when not checked the alarms are deactivated for this channel. Pressing the Alarms button
which will affect ALL widgets using this channel. This is a protected option.
Apply: Pressing this button will exit and save any changes made.
Exit: Pressing this button will exit without saving any changes made in THIS dialog box ONLY. If you
used the Setup or Alarms buttons to make changes to the channel information, these are Global and
WILL be saved.
to the channel settings which will affect ALL widgets using this channel. This is a protected
option.
Delete: Pressing this button will DELETE the Bar Chart widget. This will remove it from the
display.
Cancel: Discard all settings and exit.
Accept: Exit with settings intact.
Page 55
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Trends
Trends are the most informative and complex of all the widgets. Trends show multiple channels of data with
respect to time. The user can have multiple trend displays with different combinations of channels. Each
channel can have its own scale or all channels can share the same scale.
Trends are available in vertical or horizontal format. Vertical trend lines move from top to bottom while
horizontal trend lines move from right to left. Vertical trends are available as full size (6 across x 8 down) or
half size (6 across x 4down). Horizontal trends are available as full size (6 across x 8 down), 2/3 size (4 cross
x 8 down) or half size (3across x 8 down). Trends can be used in conjunction with any other widgets on the
display as set up in the Display Builder.
The Trend View has a number of active elements.
The Trend Setup active area is the scale as shown
right. Double tapping this area will pop-up the
Trend Scale Setup – see below.
TREND SETUP
ACTIVE AREA
The name bar below the trend is the Scale Rotate
active area. Tapping this bar will force the scale to
move to that of the next channel. The channel
identifiers show which channel scale is currently
visible and what the engineering units are.
CHANNEL
IDENTIFIERS
The Browse button on the right of the name bar
below the trend allows the user to go to the trend
historic data, zoom, measure, annotate and save
or print images of the trend.
BROWSE
BUTTON
Trends can have up to 18 channels on a display
SCALE ROTATE
although this could be extremely cluttered. Since it
is possible to create multiple trend displays, or
even displays with two (half) trends it would be
ACTIVE AREA
Figure 5-3-3 Trend View
better to group smaller numbers of channels together on their own display and cycle between them.
Channels on a single trend display can all share the same scale or can each have a separate scale. When
channels have individual scales, the scale on the trend itself will change at a predetermined interval, allowing
each channel scale to “have a turn” for a period of time known as the dwell time. Thus if the dwell time were
10 seconds, every 10 seconds the next scale would appear and the scales would cycle around. As each scale
appears, those trend lines associated with that scale will have pointers to the immediate left of the scale in
horizontal trends or below in vertical trends. This associates the trend line with the scale. The scale rotation
can be stopped and a single scale can be set continuously – see Trend Setup below.
Page 56
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.3.2.2 Trend Setup
Trend setup can be done from the Display
Builder or can be edited at any time by double-
tapping the scale of the Trend display. Double-
tapping the Trend display scale will pop up the
Trend Scale Setup window as shown right.
There are a couple of options at this point.
Scale: This is the Channel Scale rotate select.
When set to AUTO the scales will rotate
sequentially through all scales of channels on
display. As each channel is active the channel
pointer will appear on the column immediately
left of the scales and the Channel number and
engineering units will display on the bar below
MANual the first channel will have its scale
displayed and will not rotate. Scales can be
rotated by pressing the bar below the trend.
Figure 5-3-4 Trend Scale Setup
Setting Scale to ALL puts up all channel indicators and the scale is permanently set at 0 to 100 %. No
Channel number is displayed on the bar.
Dwell: This is the time period in seconds that a displayed scale will remain in view before switching to the
next. Only applies if AUTO is selected for Scale above.
Setup: Opens Trend Setup window - see below.
Exit: Returns to Trend display.
5.3.2.3 Trend Setup Window
The Trend Setup dialog window is shown in at right.
Multiple channel information as well as general Trend
display information is set up on this screen.
Enable: If this box is checked the Trend is enabled, if
this box is unchecked the Trend is disabled and will
indicate OFF in the Trend Name area.
Update: This is the screen update rate in seconds and
determines the “speed” of the Trends. A new point is
added (and the trend advances by 1 pixel) each
Update Rate which can be 0.10 seconds to 9999
seconds (10 times a second to once every 2.7 hours)
Background Color: This is the background
color of the chart. Set it so that it contrasts
with the colors set for the Trends. Black Trends on a
black background will not be visible.
Figure 5-3-5 Trend Setup
Style: This is an indication of the Trend style and is for information only. It cannot be altered here. If you
Use default Scale: This takes the user defined Default Scale (see below) and applies it to the currently
selected channel (Channel 4 in above example). This will populate the Channel Scale with the default
values. Note: Setting the channel to the Default Scale does not normalize the Trend for that scale, but
rather shows only that part of the trend that falls within the default scale. For example, if a channel had an
input scale of 0 to 200 and it was forced to use the default scale of 0 to 100, as long as the input was
between 1 and 100 the trend would be on the display, the moment the input went above 100 it would
essentially flat line against the top of the display.
Page 57
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Default Scale: The user can enter the Low Scale and High Scale values to use as the default scale.
Delete: Delete this trend. Caution – this will remove the trend from the unit.
Use Channel Scale: This loads the preset channel scale from the channel setup configuration and
makes it the current setting for the Channel Scale.
Channel: Select the channel number to customize. The channel will only appear on the Trend if it is
checked in the list at the bottom of the screen.
Channel Scale: This is the Low Scale (to the left) and High Scale (to the right) that will be used for this
channel on the Trend display. These can be preset by selecting “Use Channel Scale” or “Use default
Scale” as defined above, or they can be totally customized by tapping in the respective box and entering
the value required.
Active: If this box is checked the channel will appear on the Trend, if this box is unchecked the channel
will not be displayed on the Trend.
to the channel settings which will affect ALL trends and widgets using this channel.
Channel enable must be active in order for alarms to work.
Color: Set the color for this channel on this Trend only.
Trend Name: Enter up to 20 characters to uniquely identify the Trend display. This appears on the
Channel List: Use these checkboxes to add or remove channels from the Trend. Channels are enabled
described above.
Cancel: Discard all settings and exit.
Accept: Exit with settings intact.
Page 58
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.4 Alarms
A total of five Alarms can be set for each channel programmed. These five Alarms can be any combination of
numerous Alarm types (limits). The Alarm dead band (also known as hysteresis) and Alarm delay can also be
programmed for each Alarm type. In addition a custom event message can be created for entry into the alarm
event log and can be set up to be emailed to the user.
For all inputs other than Linear Dry Contact or Conditional, the Alarm types are: None, High, Low, Rate, or
Abnormal.
For Linear Dry Contacts and Conditional Inputs the Alarm types are: None, True (or Open), False (or Close) or
Abnormal.
The Alarm types are described below:
None
High
Low
No alarm set
Set High alarms (up to five). Alarm will occur if input is greater than the Alarm set point.
Set Low alarms (up to five). Alarm will occurs if input is less than the Alarm set point.
Rate
Set Rate alarms (up to five). Alarm will occur if the input changes by more than the set
point value in the specified time.
Abnormal
Set alarms for Abnormal conditions (TCBO, Overflow, invalid etc.)
True (Open)
Set alarm if condition is True or Open as defined (Conditional inputs and Dry Contacts
ONLY)
False (Close) Set alarm if condition is False or Closed as defined (Conditional inputs and Dry Contacts
ONLY)
If you try to program an alarm with an illegal condition, for example, setting a Linear Voltage input alarm to
“Type=False”, you will get an error.
The Alarm status is shown in the Task Bar at the bottom of the screen. This icon also doubles as the Alarm
Acknowledge button. This icon changes color as shown below:
- No alarms. Indicator is Green
- No Alarms – Alarm Muted. Indicator is Amber
- Alarm condition or Alarms disabled. Indicator is Red.
Any channel that has an alarm condition and is displayed as a digital display or bar chart, will blink its
displayed value or indicate „alarm” as long the alarm condition exists. Bar charts will also indicate
alarm set points where possible using small arrow icons - ▲ for high alarm and ▼ for low alarm as
shown on the right.
alarm and the event message if any.
Alarms are acknowledged by pressing the Alarm Acknowledge button (Alarm Status Indicator icon) in
the Task Bar. This will silence the alarm – the status indicator will continue to show status as indicated
above. The acknowledge event will be logged into the alarm/event log. If security is enabled (see
added to the alarm/event log acknowledge event.
Page 59
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Alarms will also activate relay outputs if this option is installed and set up. See Section 5.5 Digital Input/Output for
details.
5.4.1 Alarm Master Setup
Alarm setup can be done through the Alarm Master Setup or can be done on an “as you go” basis through the
Channel Setup menu when defining or editing widgets.
To access the Alarm Master Setup dialog window:
Press the Utility Setup Menu icon on the
bottom left of the Task Bar.
Then press the Alarm Master Setup
icon to launch the Alarm Master Setup
dialog window as shown right.
This is the primary Alarm Setup dialog window. It
gives an overview of the 5 alarms for the selected
channel, showing the Type, SetPoint and whether
the alarm is enabled. The edit button allows each
alarm to be modified. Note that the enable checkbox
for each alarm channel is the status only, if you
need to change this you have to press the edit
button.
Figure 5-4-1 Alarm Master Setup
Setup: Proceed to set up the individual
alarms – see below.
Channel: Below the overview is the Channel selection drop down box. This shows the current alarm setup
and allows the user to select any of the 18 channels. If you enter the setup from a specific channel, you
cannot change the channel.
Channel Enable: When checked, the alarms that are enabled for the channel will be active. When
unchecked, alarms for this channel are disabled. For an alarm to be active, the individual alarm must be
enabled AND the Channel Enable must be checked. (also see next)
Alarm Mute: When unchecked the alarms will function normally but the alarm will not sound – it will be
muted. The alarm status indicator will be amber.
Notify Enable: This enables or disables any email activity initiated by the Notify option in the Alarm Setup.
When unchecked no emails will be sent.
Master Enable: This enables or disables ALL ACTIVE alarms on ALL Channels. When unchecked, no alarms
will work and the alarm status indicator will be red continuously.
Exit: Pressing this button will exit the window, applying whatever changes have been made.
Page 60
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.4.1.1 Alarm Setup
Pressing the edit button above takes you to the individual Alarm Setup dialog window shown
below right.
The window will show the default Channel and
Alarm setup based upon entry conditions – eg
Channel 2 Alarm 1. The user can change the
Alarm Number and the window will refresh and
show the setup for that alarm.
Channel: The current channel that the alarm
setup refers to. (1 to 18). Defaults to source.
Alm No: The current alarm for the current
channel. (1 to 5)
Alarm Type: This drop down selection box
allows the user to select one of the available
alarm types. The Alarm types are: For Linear,
Square Root, Frequency and Calculated inputs -
None, High, Low, Rate, or Abnormal. For Dry
Contacts and Conditional Inputs the alarm types
Figure 5-4-2 Alarm Setup
are - None, True (or Open), False (or Close) or Abnormal. Any unused alarm must be set to None.
Enable Checkbox: If checked this alarm is enabled, if unchecked this alarm is disabled. Note: to ensure
that any alarms on this channel are active it is necessary to check the Channel Enable AND Master
Enable in the Alarm Master Setup.
Notify Checkbox: If checked the system will attempt to send an email about this alarm condition
provided the email smtp information is correctly setup.
Record Checkbox: If checked this alarm will trigger a recording to start if the record setup has been
configured this way. See Section 5.6 Record Setup.
Setpoint: This is the value in the same engineering units as the channel that the alarm condition is tested
against – also known as the threshold. In the above example, when the input is greater than (high alarm)
350, the alarm will be true. See the definition of other alarm conditions above.
Dead band: This value is the hysteresis for the alarm. Once the alarm is true (active) this value is
subtracted from the setpoint and becomes the new setpoint for the alarm reset. In the above example the
dead band is 10 so once an alarm is active, the input needs to drop below 340 (new threshold) to no
longer be true or active. This prevents chatter about the alarm setpoint. Once the alarm is reset, no longer
true, the setpoint is restored to the original value so the next alarm has to exceed 350 to once again be
active. Note: The dead band cannot exceed the setpoint.
Delay: Enter the time in seconds from the point that the alarm condition becomes true (input exceeds
setpoint) till it is actually reported as an alarm. If the alarm condition is reset (drops below the threshold)
during this delay period, the alarm will not be reported. This feature prevents an alarm condition if the
process is stable apart from a quick aberration that is recoverable.
Rate of Change: Enter the time in seconds (up to a maximum of 600) over which the input cannot
change by more than the setpoint. For example, if the setpoint was 10 and the rate of change is 5
seconds, if the input changes by more than 10 in 5 seconds an alarm will occur. If the setpoint is positive
the rate of change is measured on increasing changes, if the setpoint is negative, the rate of change is
measure on decreasing changes.
Page 61
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Event Message: Enter a message in the entry box (up to a maximum of 20 characters) that will be
appended to the alarm/event log message if the check box to the left is checked. This message will also
be appended to the email if the notify box is checked (see above).
Audio File: The recorder can play a .wav file (PCM type only) instead of the standard alarm sound.
These audio files must be saved in the system internal memory (SD Card). The drop down box shows
available files. Select the file to be played or none to use the default sound.
Contact: This is the relay output contact that will be activated when the alarm is true. You need to have
an optional digital I/O board in the system which needs to be set up correctly. The contact has to be
enabled. If no contact output is required, set this to None. If you need to set up the contact, press the
Setup button alongside the contact number to get to the Digital Output Setup window.
5.5 Digital Input/Output
The Digital Input/Output features require an optional card which is plugged into the rear of the recorder. This card
will have some combination of up to 12 relays (outputs) and 6 opto-isolated inputs, depending on model number.
Check the specifications of the card you have for the output ratings and type of the relays and the input voltage of
the opto-isolated inputs.
In order to make use of the Digital Input/Output capabilities of the recorder, these need to be setup and initialized
before use. Setup can be done through the Utility Setup Menu when defining or editing widgets.
The status of the digital outputs is indicated by the icon on the Task Bar which also doubles as the Alarm Reset
button. The Alarm Reset button will drop out any contacts that are latched and no longer in alarm, or any alarm
that is set to drop out on reset. The status is indicated as follows:
- Relay outputs all reset – safe condition
- One or more relay outputs active – alarm condition
The relay outputs can be configured in a number of ways. It is up to the user to ensure that connection and
external circuitry agree with what is set up in the relay configuration menus. The output types are as follows:
Normal: The relays are normally not energized but will energize in an alarm condition and return to normal
when the alarm clears, or will clear when the Acknowledge button is pressed if this option is set.
Latching: The relays are normally not energized but will energize in an alarm condition and will NOT return to
normal when the alarm clears, until the Acknowledge button is pressed or unless the Acknowledge button is
pressed if this option is set.
Reflash: The Reflash option programs the relays to momentarily open and reclose each time an additional
alarm that is programmed to close the contacts is acquired.
Failsafe: This is an option that can be applied to each relay output. The Failsafe option allows the relay
outputs to function as Failsafe Contacts. This reverses the logic so a contact which is normally OPEN will be
energized normally CLOSED. The Failsafe contact will drop out in the event of a power failure and indicate an
alarm.
The digital inputs are opto-coupled led types. They typically operate from 3 to 12 volts DC but can be wired for
higher input voltages. Each input has an isolated positive (+) and negative (-) connection. Check the information
that came with the card for further details.
Page 62
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.5.1 Digital Output Setup
To access the Digital Output Setup dialog window:
Press the Utility Setup Menu icon on the bottom left of the Task Bar. Then Press the
Digital I/O Setup icon which will bring up the digital IO selection dialog shown left.
Digital Output setup.
Select the Digital Output setup button to launch the Digital Output Setup dialog window as
shown in Figure 5-5-1. This dialog window provides complete control over the setup of the
digital relay outputs. No assumption is made about the type of relay output or its
capabilities; these must be checked by the user from the hardware specifications of the card
installed in the recorder.
There can be a maximum of 12 output relays. The scroll bar can be used to view contacts 7 to 12.
Enable:
This checkbox is used to enable
individual output relays. If it is checked, the output
is active, if it is not, the output is disabled. Note
that the Master Enable checkbox MUST be
checked to allow any output to function. If a Digital
IO card is not present in the recorder or there are
less than 12 relays on it, you will not be able to
check the enable box of relays not present in the
system.
Manual: These buttons enable the user to override
the current status of the relay outputs in real time.
Set – activates the relay
Reset - deactivates the relay.
Figure 5-5-1 Digital Output Setup
The icon on the button changes to indicate the current status of the output relay. The Master Enable must be
checked in order for this to operate on the outputs.
Relay Type: This drop down selection box allows the user to define the relay type as Normal, Latching or
Reflash. The descriptions are detailed above.
Fail Safe: Check this box if you want this output relay to be fail safe. This reverses the logic so a contact
which is normally OPEN will be energized normally CLOSED. Full details are shown above.
Open on Reset: Check this option if you want the Alarm Reset button to reset the contacts irrespective.
Under normal circumstances a contact will not drop out until the alarm condition clears. If the Open on Reset
box is checked, the contact will drop out when the Alarm Reset button is pressed irrespective of the alarm
condition. This may be useful if the contact is used as an alarm klaxon.
Master Enable: This checkbox must be checked for the output relays to function. If it is not checked, none of
the relays will operate.
Page 63
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.5.2 Digital Input Setup
To access the Digital Input Setup dialog window:
Press the Utility Setup Menu icon on the bottom left
of the Task Bar.
Press the Digital I/O Setup icon (left) and then
select Digital Input button (below left) to launch the
Digital Input Setup dialog window.
The Digital Input Setup window dialog box is shown
to the right. It provides complete control over the
setup of the digital inputs. There can be a maximum
of 6 inputs depending on which digital io card is installed in
the recorder. Note – If there is no Digital IO board in the unit
the enable functions will be grayed out.
Enable: This checkbox is used to enable individual inputs. If
it is checked, the input is active, if it is not, the input is
disabled and acts as though there were no stimulus on the
Figure 5-5-2 Digital Input Setup
inputs – it appears as off (false) to the system. Note that the Master Enable checkbox MUST be checked to
allow any input to function. If a Digital IO card is not present in the recorder or there are less than 6 inputs on
it, you will not be able to check the enable box of inputs not present in the system. (see status below)
Input Function: This drop down selection box allows the user to define the input type and its use. The
options are:
None: No function selected
screen icon. This will silence the local recorder alarm tone
drop out any eligible relay outputs.
Alm Both: Functions as both the Alarm Acknowledge and Alarm Reset button, equivalent to pushing one
then the other.
Event: Forces an event in the alarm/event log and prints the message in the Event Message box.
Timer Rst: Timer Reset – acts as the External Timer Reset for any timer channel that has been
programmed to be reset externally.
Total Rst: Totalizer Reset - acts as the External Totalizer Reset for any totalizer channel that has been
programmed to be reset externally.
that has been programmed to be reset externally
Record: Record enable – will cause the recorder to start recording as long as the external input is active
provided the record setup has been programmed to enable this function.
Report: Print Report – will cause a status report
calculated channel that has been programmed to be reset externally.
Status: Shows the current real time status of the digital inputs. If the status box is green, that input is not
active. If the status box is red, that input is currently active. If the status box is amber, that input is not
available.
Page 64
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Event Message: Enter the event message that will be printed in the alarm event log (and the recorded file if
enabled) in this Box. The message may be up to 20 characters in length.
Master Enable: When checked this allows external events to be recognized by the system. When unchecked
ALL external events are ignored. This allows setup without the possibility of an external event triggering the
system unexpectedly. It can also disable external events temporarily without having to reprogram inputs.
Print on Demand: This button brings up the channel selector which allows selection of which
channels will have a status printout when the input is active. The printout is serial ASCII and
outputs through the (optional) serial port only. It can be used to communicated with a remote controller or
print to a serial printer.
Page 65
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.6 Record Setup
There are several ways to start a recording. The recording can be started manually by the user, by an external
event, by an alarm event or on a time schedule. Each of these methods has to be enabled in the record setup as
well as at the source (Digital Input Setup or Alarm Setup).
The record status is indicated by an icon on the extreme right of the Task Bar as shown below:
The recorder is currently not recording and is not set to trigger.
The recorder is currently recording. This icon will blink slowly.
The recorder is armed but is not actually recording. It will start recording when an event takes place.
To access the Record Setup dialog window press the Utility Setup Menu icon on the bottom left of the
Task Bar.
If the Record Setup icon has a red circle in the bottom left hand corner (as
shown left), the recorder is currently in record mode and the Record Setup
window is not available. Instead if this button is pressed the recorder will pop up
a dialog box asking if you want to stop recording.
If the recorder is not currently recording, the Record Setup icon will have a green
circle in the bottom left hand corner (as shown left). When this icon is pressed a
Record dialog box will pop-up (shown right). The options are:
Record Now - Start Recording immediately
Record Setup – Setup record parameters as shown below.
Cancel – Exits back to the Utility Setup Menu
Note: If recording has not been set up you cannot start to
record. If the unit is recording, the dialog box will require that
you stop recording. Access to the Record Setup menu
requires log in if access protection is enabled.
The Record Setup dialog window (as shown right) contains a
lot of options that need to be set. This includes which
channels to record, what to record, the record sample rate,
the file name and location, and what events will start
recording.
There are two pages of record setup parameters. The
second page is accessed by clicking the setup button above
the accept button
Figure 5.6.1 Record Setup
5.6.1 Select Channels
To select which channels to record simply check them at the top of the window. The channels are numbered
1 through 18. In the screen shown Channels 1 through 8 will be recorded.
Page 66
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.6.2 Media and Filename
Media: Select the media and file name to record to. Choices are:
CF Card which is the Compact Flash card and is the recommended removable
media.
Internal Memory is the optional internal Secure Digital Card. It is effectively non
removable.
USB HD and USB HD2 are the USB Hard Drives (Thumb Drives or USB Flash Drives) either in the front
selection. If the media chosen is not available an error message will pop-up indicating “Media not
Present”. Once available media has been selected the amount of available free space will be indicated
below the Media selection drop down box as Space: NNN Mb where NNN is the actual amount of free
space on the selected storage media.
FileName: Enter a file name or select an existing file to append to. Files have the file type of .dat which will be
automatically appended if not entered. Clicking the FileName window will bring up the File Dialog for the
media chosen. Note that the filename entered will actually create a session folder and all related files will be
stored in this folder (sub files created by file break up, captured screens).
5.6.3 Record Rate
Select the sample rate using the Hours, Minutes and Seconds drop
down lists. The fastest sample rate is 10 times a second (0,1 seconds),
the slowest rate is once a day. The example here shows a sample
interval of once per minute. Note: file size is proportional to sample rate – the faster the sample rate the
bigger the file.
5.6.4 What to Record
Select what to record and how – Points is the actual data, check the box to record
the actual point data. Alarms will record all alarm conditions and Events are non-
alarm activities such as Record Start time. Check the box alongside each item you
want recorded onto the media.
5.6.4.1 Point type – Max Min Average.
The point type allows the user to set up how each point is recorded – maximum, minimum,
average or instantaneous (default). Click the min/max button to go to the next page.
Each point enabled to record will be shown with a drop down menu alongside. To record
anything other than the instantaneous value choose the following from the drop down list.
INST. = Instantaneous – save the data as it is read at
the record interval
MIN. Minimum - will monitor the minimum (lowest)
of all samples at 10/samples/sec and record the
minimum value over the record rate interval.
MAX.
Maximum – will monitor the maximum
(highest) of all samples at 10/samples/sec and record
the maximum value over the record rate interval.
AVG.
Average – will perform a weighted average on
all samples at 10 samples/sec and average them as
(last value + current value)/2. Note – you can use the
Filter on each channel to provide additional averaging.
Figure 5.6.2 Record Setup - Max Min Avg
Page 67
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.6.5 Timed Record
The unit can be set to start recording at a specific time and
date and stop recording at a specific time and date. To do this
check the Start Time checkbox and set the Date and Time
below it. If only the Start Time is checked this will act like a
delayed record start. If you want the recording to stop at a
specific time and date check the Stop Time check box and set the Date and Time below it. Note that the stop
time needs to be greater than the start time and the start time needs to be greater than the current time. If
you want the recording to start and stop on a daily basis check the Daily checkbox and the stop and start
time dates will be ignored and the unit will start and stop recording every day at the specified times .
There are more setup options on the second setup page accessed via the setup button.
5.6.6 Split Files
This option allows the user to split recorded data files
automatically into a sequence of smaller files. Files can be
split into 1 to 24 hour segments. At
each time point the current data file
is closed and a new file is opened. A
date time stamp is appended to the file name. This way
smaller files can be quickly downloaded (over the Ethernet)
if required. Select the split files time from the drop down
menu from 1 to 24 hours.
To disable Split Files – select NEVER.
Figure 5.6.2 - Record Setup Page 2
5.6.7 Triggered Record
There are various options that will start a recording, other than manually by the operator. The alarm triggered
events are listed below. In order to enable these events three steps are required.
Enable the event in this Record Setup dialog.
1. Set up the record trigger sources – alarms or digital inputs (External Trigger), in their respective setup
dialogs, or time in this dialog.
2. Arm the record mode by pressing the Record Setup icon (shown right) from the Utility Setup
Menu.
3. Then press Record Arm on the
pop-up window.
Alm Trig: This is the Alarm Trigger Record enable. If this box is checked, any
record checkbox checked) will activate recording when the recording is armed
and the alarm record checkbox is check and the alarm is active. Once recording starts the minimum record
time will be the duration of the alarm condition plus thirty seconds. The Alarm must be set up appropriately.
Ext Trig: This is the External Trigger Record enable. If this box is checked, any external input that has been
set up to start recording (input defined as record) will activate recording when the recording is armed and the
input has been defined as record and the digital input is active. Once recording starts the minimum record
time will be thirty seconds or the duration of the alarm condition whichever is greater.
Once set up do not forget to Arm the recorder. Do not simply start recording as this will override any triggered
settings.
Page 68
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.6.8 Media Alarm
The media alarm can be used to alert the user that the
media is nearing capacity and needs to be exchanged.
The alarm needs to be setup before the enable
checkbox is checked. The setup of the media alarms is
similar to the setup for any alarm.
Enable Checkbox: If checked the media alarm is
enabled; if unchecked the alarm is disabled. Note: to ensure that the media alarm will activate it is necessary
Notify Checkbox: If checked the system will attempt to send an email about this alarm condition provided the
email is correctly setup.
Setpoint: Alarm when Media is XX % full. This is the value in percent full at which the alarm will activate.
Select a value from the pull down menu from 60 to 100%.
Event Message: Enter a message in the entry box (up to a maximum of 20 characters) which will be
appended to the alarm/event log message if the Print check box is checked. This message will also be
appended to the email if the notify box is checked (see above).
Audio File: The recorder can play a .wav file (PCM type only) instead of the standard alarm sound. These
audio files must be saved in the system internal memory (SD Card). The drop down box shows available files.
Select the file to be played or leave blank to use the default sound.
Contact: This is the relay output contact that will be activated when the alarm is true. You need to have an
contact has to be enabled. If no contact output is required, set this to None. If you
need to set up the contact, press the Setup button alongside the contact
Use the Accept
or
Cancel
button to Return as required.
Page 69
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7 System Administrative Menu
The Administrative Menu is entered from the Utility Setup Menu by pressing the icon shown at the
right. This is a privileged option and will pop-up a new set of icons as shown below:
Fig 5.7 – System Admin Menu
The icons have the following functions:
Exit – Return to Utility Setup Menu
Analog Calibration – Allows the administrator to perform calibration on the analog inputs.
details
Temperature Compensation – Allows the Administrator to adjust thermocouple ambient
temperature compensation. Details Here
Touch Screen Calibration – Allows the administrator to calibrate the touch screen. Tap the “X” until
it disappears then tap anywhere on the screen to exit.
System Setup – Allows the administrator to set up system parameters such as device name and
Date / Time Setup – Allows the administrator to set the unit‟s date and time parameters. Details Here
User Administration – Allows the administrator to add or remove users, assign passwords, set
File Explorer – Allows the administrator to move, copy, or rename files. User can move files from
compact flash to USB drive for example. Manager/Admin only. Details Here
Page 70
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Set ActiveSync Password – Allows the administrator to set the password for USB connection via
ActiveSync. Detail Here
Save or Clear Registry – Allows the administrator to save or clear the system registry. Details Here
Load Language - Allows the administrator to load alternate languages provided the language files
Reflash Firmware – Allows the system firmware to be updated. This is potentially destructive
Page 71
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.1 Temperature Compensation
This is the Ambient Temperature Compensation adjust and is used to compensate for
adverse environments when using thermocouples. This feature is entered from the system
admin menu by pressing the icon shown right.
At the terminal blocks where the thermocouples connect to the recorder there is a new thermocouple junction
introduced which can affect the reading. There is a sensor there measuring the ambient temperature at the
terminals and is used to compensate for any offset that may result. In certain circumstances the ambient
temperature may not be able to adequately compensate for external temperatures resulting in an error in the
readings.
Selecting this option from the menu will pop up the Ambient Temp
Compensation box shown right. This box can be moved by tapping and
holding the blue bar while dragging the window. The user can view the
live thermocouple data while adjusting the compensation and can see
the actual compensation value in the box below the Deg-F checkbox.
Use the Offset dropdown box to adjust the reading by up to +3 degrees
in 0.5° increments in either Centigrade if the Deg. F checkbox is unchecked or Fahrenheit if the Deg. F
checkbox is checked.
Update button - make the adjustment.
Done button - exits the window.
5.7.2 System Setup
The System Setup allows the administrator to adjust some basic settings of the unit like Unit Tag.
bring up the System Setup dialog box.
The options are as follows:
5.7.2.1 NTP Time Server
NTP is Network Time Protocol. The Recorder has
the ability to go out over the internet and get a
time update from one of several NTP time servers
if the Time Server Checkbox is checked.
Note that you DO NOT NEED to use this unless
you want to synchronize a number of units spread
about on different networks. The unit will connect
and synchronize to any network server it finds on
the Ethernet at startup time.
There needs to be a valid IP address for NTP to
work in the IP entry box. A list of NIST Internet
Time Servers can be found at (among others)
Fig 5.7.2 – System Setup
Time Server Enable box is checked the unit will synchronize its time at startup and every 12 hours
thereafter. Note: The NTP setting is only recognized at start up. It is necessary to Save the
Page 72
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.2.2 Modbus Settings
This is only applicable if the serial port option is installed in the unit. Modbus is a communication protocol
which runs over RS232 (single unit) or RS485 (multiple units). The ID uniquely identifies the device in a
multidrop environment and can be set from 1 to 255. Note that this does not imply that 255 units can be
on line at a time. The limit is usually 32 to 64. The Baud Rate is the serial communication speed which
must match that of the host controller. This can be set from 9600 to 115200 baud.
5.7.2.3 Mouse Pointer Enable
Check this Enable checkbox if you plan on using an external mouse or other pointing device. This will
keep the mouse pointer or cursor visible at all times. Note: This setting only takes effect AFTER you
power down the unit and restart it.
5.7.2.4 Config Auto Save
Check this Enable checkbox to have the Configuration file saved automatically each time a change is
made to the unit configuration. If you are setting the system up for the first time you can disable this
feature by unchecking this box so the process is a little quicker, however DO NOT FORGET TO SAVE
5.7.2.5 Menu Timeout
The Menu Timeout sets the time in seconds after which any menu visible on the screen will collapse and
the display will revert back to the live display. Select 60 to 300 seconds from the dropdown box.
5.7.2.6 50/60 Hz Filter
In noisy environments the AC mains frequency interference can affect the readings on the most sensitive
(millivolt) ranges when running at sample rates asynchronous to the AC mains frequency. If the sample
rate can be made to run synchronously with the AC mains frequency, the noise effect of that frequency is
minimized because the recorder has differential inputs and samples at the same place on AC wave for
every sample. This does however place a limit on what the sample rates can be. The common
denominator for 50 and 60 Hz is a sample rate of 16.66 samples per second to eliminate the AC hum.
This means that the fastest sample rate to meet this requirement is around 1.5 to 2.2 samples per second
depending on the number of analog input channels in the recorder. Checking the box will activate the filter
but will limit the maximum sample rate irrespective of what is selected elsewhere. This is usually not an
issue for thermocouples and RTDs which are typically the most affected by AC noise.
5.7.2.7 Unit Tag
The Unit Tag identifies the recorder. It appears in the task bar and all data files. Enter up to 22
Once the changes have been made press the accept button
to quit without saving the changes.
to exit or the cancel button
5.7.3 Date/Time Setting
Tapping the Date/Time icon shown left will bring
up the Date/Time dialog. Here the user can set
the current Date, Time and Time Zone as well as
the date format
To change the time – tap on the hour, min, secs accordingly
then adjust using the up and down arrow keys. Select the
current time zone from the pull down menu
Fig 5.7.3 – Date – Time Setup
Page 73
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
To change the year – tap on it pull down iconwhich will pop up a calendar. Scroll through and select the
current date.
Select the required date format from the pull down menu – mm/dd/yyyy or dd/mm/yyyy.
The time can be shown in 12 or 24 hour (military) formats. Check the 24 Hour Format check box for 24 hour
format, uncheck it for 12 hour format.
Once the changes have been made press the accept button
quit without saving the changes.
to exit or the cancel button
to
5.7.4 User Setup (Password Management)
The recorder can be protected by various levels of passwords. If password protection is not enabled, the user
can move about freely without having to enter user names or passwords. If passwords are enabled the
recorder has three levels of protection:
Administrator:
Manager:
Has access to all levels of the recorder menus and systems.
Has restricted access. A Manager cannot set up any base level parameters, but can use
existing setups to create alarms, displays and the like.
User:
Can use the recorder only as set up by the Administrator or Manager. Cannot change
any parameters. Needs to log in to accept alarms.
The administrator can create or remove users and assign privileges, access restrictions and passwords as
needed.
The recorder user manager / password protection is managed in the User Management dialog
only the Administrator can access this function.
The Password Management dialog window can be used to
edit existing users or create new users. Existing users are
shown in the user list.
Security Enable: If this box is checked security is enabled
and active. If unchecked, security is disabled and passwords
are not required.
User:
Enter the name of a new user here. If a user is
selected from the list it will automatically populate this window.
Active: This checkbox will enable the specified user if checked
or disable the user if unchecked.
Fig 5.7.4 - USER SETUP
Level: This drop down box sets the user access level to User,
Manager or Administrator. See descriptions of user level above.
Auto Logout: This drop down box enables an auto logout time to be set from 0 (never) to 30 minutes. If a
time is selected, this user will be automatically logged out of the system after the specified time of inactivity.
This is a security measure to prevent leaving the recorder open if a user forgets to log out.
Expires: Set a date on which this user‟s privileges expire. After this date the administrator will have to renew
the expiry date.
Old Password: In order to change a password the original (or old) password must be entered here.
Password: Enter the user‟s password here. It can be any combination of characters and is case sensitive. If
a user is selected from the user list this box will be automatically populated.
Page 74
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Activity Log: Check this box to enable the Activity Log – this option tracks all changes made by a user and is
useful for FDA compliance. Use the Exhibitor Software to print Activity Log reports.
Add: Once user, password, and other parameters are entered this button will ADD the user to the
list. The user will be prompted to re-enter the password to accept the entry.
Update: Select a user from the list, make any changes required and press UPDATE to
modify the user. The user will be prompted to re-enter the password to accept the entry if the
password was changed
Delete: Select a user from the list and press DELETE to remove the user permanently.
OK: Accepts the changes and exits.
Cancel: Exits the dialog without making changes.
5.7.5 File Explorer
The File Explorer is similar to the Windows explorer and is used for browsing the files on the
shown right. Tap the icon to bring up the browser screen shown below. Note the screen you see
may differ depending on how you have selected the View.
The window shows all folders and media devices in the
recorder. The internal memory is the SD Card. There may
also be icons for the USB HD (Hard Drive) or the CF Card.
Note: Do not move or delete any system files or
folders as this will affect the recorder operation.
System files will be restored on system reset. To navigate
to the next level double tap the icon to access that folder
or device.
Use the View menu to select how the folders are
presented. You can choose large or small icons or a file
list with details. (Large icon view shown)
Use the scroll bars to move about the list if it should
exceed the size of the window.
Figure 5.7.5 - File Explorer
Files can be copied (from Compact Flash to USB for
example) by selecting (tapping) the file and using the Edit
menu to Copy it then navigate to the destination and use the Edit menu to Paste it. Always select (tap) the
file before using the menus to perform a function.
When the operations are complete, tap the cancel icon [X] in the top right corner to exit.
Page 75
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.6 Network Settings
Tapping the Ethernet IP Address Setting icon in
Network IP Address dialog window.
If you wish to specify an IP address, enter the information in
the IP, Subnet and Gateway text boxes. Check with your IT
person if you are unsure what to enter here.
Alternatively you can select the “Use DHCP” check box. This
allows the network server to automatically assign a free IP
address to the recorder.
The units actual IP address, whether user specified or server
Fig 5.7.6 – Network IP Address
5.7.7 Web User Manager
This allows the administrator to add users for web access (via a browser). This feature is entered
The User Manager pop up dialog appears as shown left. As a minimum there
needs to be a user named Admin for remote administration. Add remote
users as needed by selecting “Authenticate users locally” and tapping the
Add button. This will pop up a Dialog box shown below where you can enter
Username and Passwords.
Fig 5.7.7 – Web User Admin
If there is no keypad it needs to be launched manually. Do this by tapping the very bottom of the screen which
will bring up the Task Bar. Tap the keypad icon
above.
and then tap the Keyboard menu item as shown
You will have to drag the keypad around (By dragging the Input Panel header area. Enter the user name and
password (repeat in Verify password) as requested and tap the OK button.
It is necessary to remove the keypad before exiting. Tap the bottom of the screen once more to bring up the
task bar. Tap the keypad icon then “Hide Input Panel”.
Due to the small screen size you will need to drag the keypad around to enable you to enter all the data
needed.
Once completed, exit the User Manager by tapping the [X] in the top right corner.
Page 76
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.8 SMTP Email Settings
This allows the administrator to set up the email.
This feature is entered from the system admin
menu by pressing the icon shown right
SMTP is Simple Mail Transfer Protocol and is the standard
for email transmission across the Internet. The defaults for
emails are set here as follows:
From: The default name that will appear in the “From” field of
the email that is sent. It needs to be a real email address.
To: The default address of the recipient that the email will be
sent to.
SMTP IP address: This is the address of the SMTP mail
server that the email will be sent to so that it can be rerouted
to the recipient. It can be an address like 192.168.0.104 or it
Figure 5-26 System Setup
can be the name of the server. A working example of this is smtp.unlimitedmail.org. This is an email
forwarder and you can use this if you do not have anything else to use or have problems with your internal
servers.
SMTP user id: This is the user id needed to authenticate to the mail server. If you are going to use the smtp
address smtp.unlimitedmail.org, you will need to setup an account at www.unlimitedmail.org.
SMTP password: This is the user password needed to authenticate to the mail server.
Once the changes have been made press the accept button
quit without saving the changes.
to exit or the cancel button
to
5.7.9 Set ActiveSync Password
This allows the administrator to set up the password for allowing PC to USB on the recorder,
shown right
The unit can be synched to a PC via the USB B Slave port
username, but a password needs to be entered in order to
make the connection. Enter the password as shown here
and check the enable checkbox.
Once the changes have been made press the accept
button
to exit or the cancel button
to quit
without saving the changes.
Note: These changes will be in effect the next time you
restart the unit. It is necessary to Save the Configuration
and restart the unit (you can, with caution use the reset
Fig 5.7.9 – USB ActiveSync Password
Page 77
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.10 Registry
The Registry option allows the user to clear or save the registry. The
Registry holds system base setup values not in the configuration file and
needs to be saved if system setup changes have been made – for example
recalibrating the stylus, or may need to be cleared if upgrading the firmware. This feature is
entered from the system admin menu by pressing the icon shown right.
This will bring up the dialog box shown on the left. The user has three choices. The top
button will save the registry settings to system nonvolatile memory. The middle button will
clear the registry and set it to factory default values – Note: Do not clear the registry unless required to do
so by a system firmware upgrade. The lower button allows the user to exit without affecting the Registry.
Page 78
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
5.7.11 Languages
The languages option allows the users to
customize the unit language for the local country
by loading preconfigured language files. This
the icon shown right.
This will bring up the language dialog screen. NOTE:
Loading a new language will unload the existing
configuration file.
Select the pull down menu to display a list of available
languages. The recorder will check the internal memory for
the language file. The user needs to load the language file
“MultiLanguage.CSV” onto the root of the internal memory
card. This is a spreadsheet style file with English in the first
Figure 5.7.11 – Language Screen
column and alternative languages in subsequent columns. It is (and needs to be) in Comma Separated
Variable format.
This language file can be edited using a standard spreadsheet editor such as ExcelTM and any language can
be added following a simple set of rules – See Appendix C
Note: Save the file as .CSV and NOT .XLS format.
Select the language of choice and press the okay button.
language on the fly. The default language is English.
The recorder will change to the new
5.7.12 System ReFlash
This option allows the administrator to upgrade the system firmware. Once started this operation cannot be
reversed. Choosing to proceed will require a system reset even if you cancel the operation.
DO NOT RESET the unit, DO NOT REMOVE POWER and DO NOT PRESS THE ABORT BUTTON while
this operation is in process as it WILL MAKE THE UNIT INOPERABLE.
Before proceeding you need the image file that will be loaded. This file is called NK.bin and is
available from your service center or can be downloaded from the web. Ensure that you need to
(NK.bin) onto removable media – compact flash drive or USB thumb drive, and insert this into the
recorder before starting this procedure.
and accept the warning notice shown right and proceed with caution.
You then need to accept or skip erasing the registry – this information will be in
the release notes with the firmware. In some instances, failure to erase the
registry will cause the unit to malfunction after reflash.
Page 79
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5 – Recorder Setup
Once beyond this step The file dialog box shown below right will appear.
Select the media from the Media dropdown box.
Note that CF Card is the compact flash card - USB
HD is the front USB port - USB HD2 is the rear USB
port and Internal is the system memory AND
SHOULD NOT BE USED TO REFLASH the unit.
Browse to the file NK.BIN that you previously loaded
onto a USB Drive or Compact Flash card and select
it or enter the name into the FileName space.
Press the Accept Button This will replace the
entire contents of non-volatile memory with a new
image. This is equivalent to formatting the hard drive
on your PC and reinstalling everything. DO NOT
RESET and DO NOT REMOVE POWER while this
operation is in process. Once you select this
option a file browse window will pop up. Navigate to
Figure 5.7.12 – Reflash File Dialog
the file NK.BIN and press okay. A window will pop
up showing the progress of a series of operations. When completed you will be required to Reset or Power
Cycle the recorder to restart the system. Remove the AC mains cable and reinsert it or push the reset button
to restart. The unit will have to then be set up from new. See Section 2.7 QUICK START GUIDE.
Page 80
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.0 COMMUNICATION
There are various ways to communicate remotely with the recorder. The Ethernet port can be used to
communicate on a network or via the World Wide Web (Both HTTP and FTP protocols). There are various means
of doing this as simply as using a web browser, or using third party software using either the OPC (Open
Connectivity) protocol or Modbus™ both of which are supported by the recorder. The slave USB port on the rear
of the unit can be used to communicate with a local PC using Microsoft‟s ActiveSync™. An optional isolated serial
port is available which supports the RS232 and RS485 standards.
In order to run the web services you need to know the IP Address of the recorder. This will have been set in the
Network Settings and may be user assigned or assigned by the network using DHCP. To see the local IP Address
use the System Information button in the Setup menu. If the recorder is on a wide area network you will have to
use this Internet Address to access the unit.
The recorder reserves “ports” or sub-addresses which it uses for various services. Some of these are global
standards others are specifically reserved. This is important if you are going to make the unit accessible globally
and have a firewall or other router between the recorder and the outside world. Typically one would use a feature
of the router known as port forwarding, the exact method is router specific and if this is what you want to do,
contact your IT department or consult the router manual. The ports used by the recorder are as follows:
Port 21
Port 80
Port 135
FTP server
HTTP Server
DCOM TCP
Port 500-510 Various Server Functions
Each application that accesses the recorder has its own unique settings so as to not run afoul of Windows
Security settings, firewalls etc. These are dealt with below.
The available Exhibitor software is an extremely versatile program that supports the recorder and can replay
recorded data files in various formats, export to Excel™, view and save real time data, upload and download files,
configure recorders and allow the user to control all aspects of the recorder remotely.
6.1 World Wide Web
The recorder has a web server that supports both http and ftp requests. This enables a user to view the current
status of a remote recorder in real time and upload or download files using the World Wide Web and your browser
(The software is optimized for Internet ExplorerTM Version 6 or higher). In order to use this service it is necessary
to enable ActiveX on the browser and download Sun‟s JavaTM Engine – the program will prompt for this.
The user needs to set up users and passwords locally at the recorder. To access the web server, any user name
and password set up in the web user manager dialog will work. To access the ftp area the user name has to be
Admin and the corresponding password as set up must be entered.
The minimum system requirements for using Browser ftp are as follows:
Operating Systems: Windows 98/2000/XP/ME, Mac OS 8.x, 9.x, 10.x,
Linux, Unix
Browser: Internet Explorer, Netscape Navigator, Opera. Mozilla, Safari,
Firefox
Browser Java VM: Java 1.1 or above
To start, open your browser and type the IP address into the address bar. If you
are asked about running active content – check the “allow blocked content” option
– this site uses ActiveX. This will bring up the permission box shown right. Enter a
valid user name and password and press OK.
Fig 6.1.1 – Permission Box
If the password is correct this will bring up the live data page as shown below:
Page 81
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
Figure 6.1.2 – Index Page
The recorder name is shown in bold at the top of the page – “Process Recorder”. If any channel is in alarm this
name will be in red as shown, otherwise it will be in blue. Each channel data is shown as a digital panel indicator.
The actual value is shown in the center in large digits. Below this are the unit tags (in blue) and the engineering
units. Above to the right of each panel display is the physical channel number. In the event that a channel is in
Alarm, this will be shown in the upper left in large red letters as in the case of Channel 2. The live data updates
every 3 to 5 seconds.
There are a number of buttons below the live data display. “Chan 7-12” and “Chan 1-12” show those channels – 7
to 12 or all channels 1 to 12. “View Recorder” shows the actual recorder display as seen at the recorder itself as
shown below. This updates every 5 seconds.
Figure 6.1.3 – View Recorder Page
Page 82
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.2 Web Based FTP Manager
The “File Manager” Button brings up the FTP
launch window. Note that you need internet access
to run the FTP File Manager and the Java Engine
must be present. Click the big button to proceed. If
internet access is not available you can run the
“here” link. This is a standalone Windows only
program on the installation disk. It needs to be
installed in accordance with the instructions.
The FTP Manager is used to transfer files between
your local PC and a remote recorder. FTP is short
for File Transfer Protocol a standard for file transfer
over the internet.
Figure 6.2.1 – FTP Launch Page
If you proceed to the browser based FTP File Manager you will need to have or get the JavaTM file in order for
the program to work.
If you do not have the JavaTM program you will not see the FTP Manager but will see the
Java button. Click this to go the Java.com site and click the free download button. This
may take some time depending on your connection speed.
Once downloaded, you may get several warning notices or
security warnings. You need to accept or run the programs
in order for the site to operate properly.
Once the program has been downloaded and
installed you should not see these messages the
next time you run the web browser.
If installed correctly or if it already exists you will
see a popup box asking for a password. Note that
you need to enter the Admin password to access
the FTP File Manager as shown below.
You will always see the Java download engine loading the application before you
are asked for the password to access the recorder FTP server. Remember this is
the Admin password which may be different to the User password.
You may also need to adjust your security settings – In internet Explorer this is
done under Tools – Internet Options – Security. The setting should be “Medium”.
If you are not comfortable with this you need to use custom settings.
You may be prompted each time you access the web server to allow the content to run. Accept this and
continue.
If everything is installed correctly and you enter the correct password you should see the FTP File Manager
shown below.
Page 83
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
Figure 6.2.2 – FTP File Manager Page
The red numbers are used for reference purposes only and do not appear in the actual browser window. The parts of the
screen are as follows:
1. Current local directory - Displays the full path of your current local directory on your computer. It has the heading
“Local File System” . To the left is a drop down box allowing selection of local drives.
To the right is the
current path – c:\my_work_files.
The icon to the right of the path is to go up in the directory tree. A single left mouse click
activates.
2. Local file listing - Displays files and child folders in your current local directory. The current active file or folder is
highlighted in blue.
3. Local toolbar - Buttons for performing actions on your local directory. Simply left click to perform the function (on the
highlighted file or folder if applicable). Functions are as shown on the buttons.
4. Current remote recorder directory - Displays the path of the current remote recorder directory. It has the IP address of
the connected recorder as heading – 192.168.1.193 in this example. The current path points to the folder /1-7-2008 on
the Compact Flash Card (CF Card). Note that the recorder has a device structure rather than drives – i.e CF Card and
USB HD rather than D: and E: . The file icon to the right of the path is to go up in the directory tree.
5. Remote file listing - Displays files and child folders on the current remote recorder directory.
6. Remote toolbar - Buttons for performing actions on your remote recorder directory. Always proceed WITH CAUTION
when making changes to the remote recorder
7. This is the pop-up windows that is activated when you right click the mouse over a file or folder item. It works on the
remote as well as the local file listings. Always proceed WITH CAUTION when making changes to the remote recorder
8. Upload / Download/Help - These buttons allow you to upload and download files or sees this help information.
9. Back – takes you back to the browser functions for live data – note the browser back button may not do this if you have
been active in the file manager. If you have a popup blocker hold the CTRL key before clicking the help button.
Page 84
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
10. This is the connection to the Java web site to allow download of the Java Engine that runs this program. It may be the
only thing you see if Java is not installed.
The FTP Manager allows for file manipulation between the local PC (computer) and the remote recorder. It
functions much like Windows ExplorerTM and allows files to be uploaded or downloaded between devices,
allows files to be renamed, moved, copied and deleted. This program limits access to the certain folders
and all media in the recorder to prevent accidental deletion of system files that could stop the recorder from
operating. Proceed with CAUTION.
Page 85
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.3 Ethernet Protocols
6.3.1 OPC Server
The Recorder supports The OPC Standard (Open Connectivity over Open Standards). It is a standard used
to move real-time data from PLCs, DCSs, and other control devices to HMIs and other display
clients. The recorder is compliant with OPC Data Access 3.0, 2.0, and 1.0a standards and also
supports OPC Security 1.0.
The OPC standard is supported by the associated software suite available for PC which
interfaces to the recorder to provide remote real time data access as well as other third party
OPC software clients. Refer to the Exhibitor manual for details
Page 86
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.3.2 Modbus Server
The recorder supports ModbusTM RTU (Remote Terminal Unit) over Ethernet and optional RS485 interfaces.
An RS485 interface will support up to 64 Data Recorders linked to a single computer. Each of the Recorders
will be identified by a unique unit address (programmed under System Settings - Modbus). This address is set
at 1 to 256 and must be different from any other recorder on the loop. Similarly if using the RS485 serial port
the baud rate must be set to match the system – 9600 to 115,200 baud.
Modbus over Ethernet is supported through Port 502.
Note that Modbus ASCII is not supported and this recorder supports a minimal subset of registers and is read
only. The functions included in the subset are
Function 3 - Read Holding Registers
Function 4 - Read Input Registers
All Modbus registers are 2 bytes = 1 word.
6.3.2.1 Modbus Status Registers
The Status Registers Are 16 bit Integers in the form of two bytes as follows (Low Byte = Bits 0 through 7).
Bit 15 - 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Not
Used
Not
Used
Not
Used
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
Any
Alarm
Alarm 5
Alarm 4
Alarm 3
Alarm 2
Alarm 1
When the bit is a “1” the condition is true. There is one register for each point or channel and the registers
start at number 3056. So Register no. 3056 is Channel 1 status, Register 3057 is Channel 2 status through
Register 3071 which is Channel 18 status. These Registers are read only and are accessed using
Function 4.
6.3.2.2 Modbus Data Registers
The Data Registers hold the current floating point value for each of the 18 data points (Channels) as IEEE
floating point numbers which require 4 bytes (2 words) as shown below. They are in the format
Sign Bit Exponent (+127 biased)
Mantissa (Extra implied 1 bit)
1 bit
8 bits
23 bits
Byte 0
Byte 1
Byte 2
Byte 3
SEEEEEEE EMMMMMMM MMMMMMMM MMMMMMMM
High Word Low Word
The following tables show the mapping of the recorder parameters into Modbus registers. Knowledge of
these Modbus register assignments is only needed to make use of third party communications software.
Both registers – high and low, must be accessed together to ensure valid data.
Page 87
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
Table 6.3.2.2 Holding Registers 4xxx (Use Function 3 to Access)
32 Bits ModiconTM Format Floating Point
Writing to these registers has no effect
Register #
4361
4362
4363
4364
4365
4366
4367
4368
4369
4370
4371
4372
4373
4374
4375
4376
4377
4378
FUNCTION AND STATE
Register #
4379
4380
4381
4382
4383
4384
4385
4386
4387
4388
4389
4390
4391
4392
4393
4394
4395
4396
FUNCTION AND STATE
Point 1 Data Low Word
Point 1 Data High Word
Point 2 Data Low Word
Point 2 Data High Word
Point 3 Data Low Word
Point 3 Data High Word
Point 4 Data Low Word
Point 4 Data High Word
Point 5 Data Low Word
Point 5 Data High Word
Point 6 Data Low Word
Point 6 Data High Word
Point 7 Data Low Word
Point 7 Data High Word
Point 8 Data Low Word
Point 8 Data High Word
Point 9 Data Low Word
Point 9 Data High Word
Point 10 Data Low Word
Point 10 Data High Word
Point 11 Data Low Word
Point 11 Data High Word
Point 12 Data Low Word
Point 12 Data High Word
Point 13 Data Low Word
Point 13 Data High Word
Point 14 Data Low Word
Point 14 Data High Word
Point 15 Data Low Word
Point 15 Data High Word
Point 16 Data Low Word
Point 16 Data High Word
Point 17 Data Low Word
Point 17 Data High Word
Point 18 Data Low Word
Point 18 Data High Word
Page 88
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.4 USB Connections
The recorder can communicate via the rear USB Type B Slave port to a PC running Windows XP and Microsoft‟s
ActiveSync™ which can be downloaded from the Microsoft Website at
Note that users with Microsoft Vista do not need ActiveSync – synchronization settings will be managed
through the Windows Mobile Device Center.
Ensure that the USB Port on the recorder is properly configured using the switch at the bottom rear of the
recorder to select the Slave port. Additionally the user can set a password to protect USB access to the recorder.
Connect the recorder USB B port to the PC. If Vista or Windows XP with ActiveSync is running, the recorder will
be identified as a Microsoft Mobile Device and the ActiveSync connection dialog will pop up.
The following description is for Windows XP and assumes
Microsoft‟s ActiveSync™ is installed and running. If it is
installed the icon will be visible on the bottom right of the screen
as shown left.
Once the recorder is plugged into the USB port it should be
recognized as a Microsoft USB Sync Device and ActiveSync
be asked for this
password. Enter the
required
password
and ActiveSync will
show the window
shown right. Select
No to the “Set Up a
Partnership” request. Note the recorder does not have the ability to
synchronize.
Click the Next > button and a connection should be made – screen left.
You can use the “Explore” option to browse files on the recorder. Do
NOT delete system files on the recorder.
The following description is for Windows Vista. The first time the recorder is
plugged into the Vista machine it will be recognized and the driver will be
loaded. The recorder is identified as a Microsoft USB Sync device - right.
asked for this password. Finally the
Windows Vista Mobile Device Manager
should auto launch – shown right.
Select the “Open device to view files”
option to explore the files on the recorder.
Do NOT delete system files on the
recorder.
Page 89
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.5 Utility Programs
The utility programs provide a method of communicating with the recorder to move data or control operation
remotely. The programs are on the CD that came with the unit. To install the programs, insert the CD in the Drive
(Windows based PCs) and it should auto launch. If it does not, run the program CD_Start.exe on the CD. The
setup program has various options as shown below:
Fig 6.5 – Recorder Setup Program
6.5.1 FTP Manager
FTP is short for File Transfer Protocol a standard for file transfer over the internet.
The FTP manager is a standalone file manager for
uploading and downloading files from remote
recorders. It is installed from the installation disk that
came with the recorder. Refer to Fig 6.5 above. Click
the “FTP Manager Setup” button – This will launch
the installer. Follow the instructions and use the
default file location as shown left.
Click “Next” and the installation will proceed. Once
installation is complete, click “Close” to finish.
If you selected the add icon option during installation
it will appear on your desktop
Page 90
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
The program is launched from the desktop icon shown right or from the programs menu. The
program launches the window below:
Figure 6.5.2 – FTP Manager
The red numbers are for reference only. The software is intended for use with the recorders only – it is
specific to this task. This FTP client is specifically for intranet use but will work over a wide area network
The functions of the program are as follows:
1
Connection information. The Server IP is the address of the recorder. You can get this from the system
information button on the setup menu. Note: If you are using the world wide web you will need to know
the real address of your firewall/router which needs to be set up for port forwarding to the recorder IP
address. You also need the User Name and Password. The program remembers User Names and IP
addresses and you can use the drop down menu to select previous entries. Once set up you need to
connect to establish a link to the recorder. See 5 below
2
3
4
Local file listing - Displays files and child folders in your current local directory. The current active file or
folder is highlighted in blue.
Remote file listing - Displays files and child folders in your current remote (recorder) directory. The current
active file or folder is highlighted in blue.
Upload and Download buttons to initiate transfer of highlighted files from source to destination. Be careful
about loading files to the recorder.
Page 91
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
5
Connect and Disconnect buttons – will initiate the actual connection to the recorder. The button with the
green dot is connect, the one with the red dot is disconnect.
Refresh button – this will update the directory listings on the local and remote windows.
Help button – provides this information.
6
7
8
Right click mouse button option to delete a file or folder.
Note that when you mouse over any file or folder, a pop up bar will show the details of the item – file size and last
modified date and time.
The FTP Manager allows for file manipulation between the local PC (computer) and the remote recorder. It
functions much like Windows ExplorerTM and allows files to be uploaded or downloaded between devices,
allows files to be renamed, moved, copied and deleted. Proceed with CAUTION to prevent accidental
deletion of system files that could stop the recorder from operating.
Once the program is launched enter the IP Address of the recorder (or select it if it has already been
entered before) and enter the user name and password. Click the Connect Icon and if
the recorder is active on the network connection will be made and the file directory will
be displayed. Files may be moved between the recorder and the local PC and may be
deleted on the recorder. Be careful when uploading files to the recorder or deleting files. It is recommended
you work with data and configuration files only.
Page 92
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.5.2 Remote Control
There are two remote control programs available for controlling the recorder over the Ethernet. Remote
Display is recommended if you are on the same network as the recorder. Remote Manager allows control of
the recorder over a wide area network (WAN) when the recorder is on the other side of a firewall. The Remote
Manager funnels all communication through a single port and is consequently slower than the Remote
Display. Both programs allow a user to sit at a PC and operate the recorder as though they were right at the
unit.
6.5.2.1 Remote Display
The Remote Display program is installed from the software installation disk that came with
the recorder. This program requires support programs that need to be in the correct folder
which is managed by the installation. If these files do not exist you will get an error
message. This program will only work on a local area network. Once installed it is
launched by double clicking the Remote Display Icon shown right. This launches the
program window as shown below.
Select an IP Address from the pull down menu or
add a new one by clicking the ADD Recorder
Icon – shown right. This will pop up a form to
enter IP Address, Description and User name.
Once this is added click the ADD button to close.
Enter the password (which is never stored) and
then press the Connect Icon –
This will launch a separate window and make
connection with the recorder. It will display a real time image of the
recorder screen which updates every second and is interactive. Use
Fig 6.5.2 - Remote Display
the mouse cursor to tap on the “screen” as though you were touching
the actual recorder screen. You can now do everything you could if you were physically in front of the actual
recorder.
The window menu functions are
File: Connect or Exit. These should not be used but
rather use the control window above.
Zoom: This enables x1, x2 or x3 zoom of the recorder
screen in the window.
Tools: Send all mouse moves – this is active irrespective
of the setting.
Help: About shows the copyright and version number
You may control the recorder any way you wish. To
terminate the connection hit the “X” in the upper right
corner or preferably the disconnect button in the control
window
Fig 6.5.3 - Remote Recorder
Page 93
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 6 - Communication
6.5.2.2 Remote Manager
The Remote Manager program is installed from the software installation disk that came with
the recorder. This program will run on a WAN (Wide Area Network) – over the Ethernet and
will work through a Firewall if the firewall is set up correctly. It will work over a LAN (Local
installed The Remote Manager is launched by double clicking the Remote Manager Icon
shown right. This launches the program window as shown below.
Fig 6.5.4 - Remote Manager
Select an IP Address from the pull down menu or add a new one by
clicking the ADD Recorder Icon – shown right. This will pop up a form
shown left to enter IP Address, Description and User name. Once this is
added click the ADD button to close.
Enter the password (which is never stored) and then press the
Connect Icon (right). If the user name and password is correct and the
recorder is accessible an image of the recorder screen will appear in
the window as shown below. If the program has to navigate the WAN it make take several
seconds to connect.
Fig 6.5.5 - Remote Manager Connected
You may control the recorder any way you wish. To terminate the connection hit the “X” in
the upper right corner or preferably the disconnect button in the control window(right).
You can zoom the display by pressing the Zoom Icon.
Page 94
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7 - Instrument Care and Maintenance
7.0 INSTRUMENT CARE AND MAINTENANCE
7.1 Touch Screen
Care should be taken with the touch screen when handling the unit. Sharp and hard objects may pierce the touch
screen and damage the display. Only use the stylus provided for screen selection.
Clean the screen according to the instructions below. Abrasive materials will damage the touch screen.
7.2 Cleaning Instructions
The unit may be cleaned by wiping with a soft cloth. The front panel and display / keypad may be wiped with a
slightly damp soft cloth containing soapy solution or a mild detergent. Do not use any lemon based (citric acid)
product to clean the display / keypad. If the unit has been properly installed in a panel using the gasket and the
door is locked, the unit can withstand a low pressure hose down in accordance with IP65.
7.3 Calibration
It is recommended that recorder calibration is checked at least every year, or in accordance with your industry
regulations, to ensure maximum accuracy. It should be performed by a certified Calibration Laboratory using
National Institute of Standards and Technology - NIST (or equivalent) traceable calibration references with an
Note: Altering the calibration will affect the operation of the unit. These functions should only be
performed by qualified personnel. If security is enabled access is restricted to Administrators only.
You will need a voltage calibrator capable of generating the voltages indicated below, a 250 ohm 0.05% resistor
and a couple of shorting blocks.
It is suggested you read this entire chapter before attempting to calibrate a unit.
The calibration function is access through the Administrative Menu by pressing the icon button in the
System Utilities menu and selecting the “Analog Calibration” option.
The options in the dialog window are as follows:
Channel: Select the channel to which the signal is attached
Range: Select the Range to be calibrated (See table below)
Calibration Function: Select what is to be done from the
drop down menu as follows:
Zero Cal – Calibrate the offsets on the Analog converter.
Apply 0 Volts to the selected channel. Doing this on one
channel calibrates all channels.
Full Cal – Calibrate the full scale ranges – needs to be
done for each input range. Apply the voltage in
parentheses for each range. Doing this on one channel
calibrates all channels.
Zero Cal RTD – Calibrate the offsets for the RTD ranges.
Figure 7.1 – Calibration Window
Apply a jumper across + - COM. This needs to be done
Page 95
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7 - Instrument Care and Maintenance
for each channel.
Current Cal RTD – Calibrate the unit‟s current excitation source. Apply a 250 Ohm precision resistor. Doing
this on one channel calibrates all channels.
1 Hz Cal – Calibrate the units frequency reference. Apply a 1 Hz signal to channel 1, 6, 7 or 12. Doing this
on one channel calibrates all four channels.
Store Cal – This saves the new calibration settings into non-volatile memory.
Set Channel:
Activate the Channel to be calibrated. This will enable the Live Data.
Calibrate: Perform the calibration – This is non-reversible.
Live Data: Shows the actual live input on the selected Channel.
Restore Factory Calibration:
Will restore the calibration data that was in effect when the unit shipped
from the factory by pressing the “Restore” button
Note: Restoring the factory calibration values may negate the current calibration of your unit unless the
factory calibrates the unit on a regular basis.
7.3.1 Calibrating Linear Voltage Inputs:
You will need a shorting jumper (no connection to COM) and the voltage calibrator.
7.3.1.1 Set Channel
Select the Channel the calibrator is connected to and
select the Voltage Range to be calibrated from the
drop down menus and press the “Set Chan” button.
The “Live Data” window will show the
current value from the connected
source and a “Channel has been set
successfully” popup will appear.
Press “OK” in the top right corner
7.3.1.2 Zero Cal
Select the Zero Cal function from the Calibration
Function drop down menu.
Apply 0 Volts (Shorting jumper or
set Calibrator to 0V) to the channel
selected in step one and press the
Figure 7.2 – Calibration Window
“Calibrate” button. Doing this on
one channel calibrates all channels. On completion of the step you will get a
“Calibration Function OK" popup dialog. Press “OK” in the top right corner.
7.3.1.3 Full Cal
Select the Full Cal function from the Calibration Function drop down
Voltage Range Full Scale Input
±125mV
±250mV
±500mV
±1.00V
146mV
292.5mV
585mV
1.170V
3.125V
6.250V
12.50V
25.00V
menu.
Select the Range to be calibrated from the Range drop down menu.
Apply the Full Scale Input voltage for the selected range from the table
to the right. The output of the calibrator is connected to the IN+ and
IN- inputs on the selected channel. There is NO CONNECTION to
scale calibration value is greater than the voltage range. The “Live
Data” window will show the current value from the connected source.
Press the “Calibrate” button to complete the calibration. Doing this on
±3.00V
±6.00V
±12.00V
±24.00V
Page 96
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7 - Instrument Care and Maintenance
one channel calibrates all channels. Accept the “Calibration Function OK” popup dialog.
To calibrate another range repeat from step 6.3.1.3. Calibrate all or as many ranges as you need.
7.3.1.4 Store Cal
Once all the required ranges are calibrated, select “Store Cal” function and press the “Calibrate” button.
Accept the “Calibration Function OK” popup dialog.
7.3.2 Calibrating the RTD Current Source
This step requires a shorting jumper (one or more with COM connection) and a
precision resistor.
There are two steps – zero offset which needs to be done on EVERY RTD
channel and calibrating the current source which can be done on ANY channel.
Note the link on the resistor connector IN- to COM. Keep resistor lead length to a
minimum. Note: The “Live Data” window only shows voltage inputs during this
process.
7.3.2.1 Zero Cal RTD
This needs to be done on each channel intended for use as an RTD input.
Select the first channel to be zeroed in the Channel drop down menu box and
select “Zero Cal RTD” in the Calibration Function drop down menu box. The
Range does not matter. Press the “Set Chan” button. A “Channel has been set successfully” popup will
appear. Press “OK” in the top right corner.
Plug a shorting jumper into the selected channel and press the “Calibrate” button. On completion of the
step you will get a “Calibration Function OK" popup dialog. Press “OK” in the top right corner.
Repeat 6.3.2.2 and 6.3.2.3 above for each RTD channel – remember to move the shorting block to the
respective channel.
Once all the required ranges are zeroed, select “Store Cal” from the “Calibration Function” drop down
menu and press the “Calibrate” button. When the “Calibration Function OK" popup dialog appears press
“OK” in the top right corner.
7.3.2.2 Current Cal RTD
This only needs to be done on one channel to calibrate all. Note that the Live Data should be ignored.
Select the channel to use in the Channel drop down menu box and select “Current Cal RTD” in the
Calibration Function drop down menu box. The Range does not matter. Press the “Set Chan” button. A
“Channel has been set successfully” popup will appear. Press “OK” in the top right corner
Plug a 250Ω resistor into the channel selected above and press the “Calibrate” button. On completion of
the step you will get a “Calibration Function OK" popup dialog. Press “OK” in the top right corner.
Select “Store Cal” from the “Calibration Function” drop down menu and press the “Calibrate” button.
Accept the “Calibration Function OK” popup dialog.
7.3.3 Calibrating Frequency:
This only needs to be done on one channel to calibrate all, however it has to be done on a frequency input
channel – 1, 6, 7 or 12. You will also need a calibrated 1 Hz signal.
Page 97
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 7 - Instrument Care and Maintenance
Select the channel to use in the Channel drop down menu box (1, 6, 7 or 12) and select “1 Hz Cal” in the
Calibration Function drop down menu box. The Range does not matter. Press the “Set Chan” button. A
“Channel has been set successfully” popup will appear. Press “OK” in the top right corner
Apply a calibrated 1 Hz signal (0 to 5V signal typical) into the channel selected above with the positive signal
going to Fin and the ground to COM (See Section 2.4.3.6 for connection detail). Press the “Calibrate” button. On
completion of the step you will get a “Calibration Function OK" popup dialog. Press “OK” in the top right corner.
Select “Store Cal” from the “Calibration Function” drop down menu and press the “Calibrate” button. Accept the
“Calibration Function OK” popup dialog.
In the event that you corrupt or adversely affect the calibration, you can repeat it checking your input sources or
as a last resort restore the known good factory calibration by pressing the “Restore” button.
Page 98
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Technical Specifications
APPENDIX A – TECHNICAL SPECIFICATIONS
DISPLAY
Display Type Color
CCFL backlit Active Matrix TFT Liquid Crystal Display (5.6 inch) QVGA with resistive
analog touch screen control.
Resolution Color
Display Modes
320 (H) X 234 (V) pixels.
Graphics (Trending vertical or horizontal), Bar Graphs (vertical or horizontal, large or
small), Digital Meter (large or small), Alphanumeric Alarm and Event Log. Display builder
allows user to create custom displays
Virtual Chart Speed
Display Windows
Programmable: 0.5 in/hr to 600 in/hr (10 mm/hr to 15,000 mm/hr) ??
Time/Date, Graphics (Bars, Large Digital, Trends), Disk Status, System Status, Menu
Button Bar, Unit Identification, Alarms/Events
POWER
Power Requirements 100 to 240 Vac, 50/60 Hz. 35 VA max. Optional 24 Vdc + 15%
Power Fail Protection Programmed parameters stored in non-volatile memory. Clock battery backed. Internal
battery backup provides orderly shutdown and the ability to survive brownouts and short
blackouts (<20 seconds). Data retention time without power 3 months
Power Output
Optional isolated 24Vdc @100mA output
ANALOG INPUTS
Number of Inputs
Input Resolution
Input Impedance
Maximum Input
Isolation
6 or 12 direct inputs plus 6 additional calculated channels
0.0015% of full scale, 16 bit unless otherwise stated
>1megohm
50 Vdc
Installation category II: Pollution Degree 2
350 Vdc or RMS AC channel to channel, 2000 Vdc or peak AC Channel to Chassis
Measurement Rate
10 times per second on all direct input channels
Common Mode Noise Rejection
Normal Mode Noise Rejection
>100 dB, 50/60 Hz filter enabled
>50 dB at 50/60 Hz, filter enabled
Math Functions
fully programmable +, -, x, /, square root, sine, cosine, tangent, log, totalization, powers,
averages, conditional logic – AND, NOT, OR, +, >, <, gated timers. Can use live channels
in calculation. Can define 6 constants and 6 functions per channel.
Analog Input Signals: DC Voltage:
Bipolar Input
Full scale ranges: +125mV, +250mV, +500mV +1.00V, +3.0V, +6.0V, +12.0V, +24.0V
Accuracy:
Ranges to 1V ±0.06%:
Ranges > 1V ±0.1%
DC Current:
(with external shunt) 4 to 20 mA, 0 to 20 mA and 10 to 50 mA
Accuracy ±0.15% using external 50 ohm 0.1% shunt
Page 99
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Technical Specifications
Thermocouple: Per ITS90 Resolution 0.1°C
Thermocouple burnout detection - automatic
Type Range (°C) Accuracy (°C)
Range (°F) Accuracy (°F)
J
-210 to -100 °C ±2.5 °C
-100 to 1200 °C ±1.5 °C
-340 to -150 °F ±5 °F
-150 to 2190 °F ±3 °F
K
T
E
N
-270 to -100 °C ±2.5 °C
-100 to 1372 °C ±1.5 °C
-450 to -150 °F ±5 °F
-150 to 250 °F ±3 °F
-270 to -100 °C ±2.5 °C
-100 to 400 °C ±1.5 °C
-450 to -150 °F ±5 °F
-150 to 750 °F ±3 °F
-270 to -100 °C ±2.5 °C
-100 to 1000 °C ±1.5 °C
-450 to -150 °F ±5 °F
-150 to 1832 °F ±3 °F
-270 to -100 °C ±2.5 °C
-100 to 1300 °C ±1.5 °C
-450 to -150 °F ±5 °F
-150 to 2372 °F ±3 °F
S
B
-50 to 1768 °C ±3 °C
0 to 1820 °C ±4 °C
-58 to 3200 °F ±6 °F
32 to 3300 °F ±7 °F
Reference junction compensation accuracy ±0.5 °C (0 °C to 50 °C)
RTD: Base accuracy 0.2% or 0.5 °C (1 °F). Resolution 0.1 °C.
2, or 3 wire connection. Cable compensation to +50 Ohm. Open and short-circuit detection.
10 ohm Cu.
100 ohm Pt.
100 ohm Pt.
200 ohm Pt.
200 ohm Pt.
100 ohm Ni.
120 ohm Ni.
-70 to 170 °C
-94 to 338 °F
-364 to 1560 °F
-292 to 1500 °F
-364 to 750 °F
-292 to 750 °F
-94 to 570 °F
-94 to 570 °F
-76 to 408 °F
385 -220 to 850 °C
392 -180 to 820 °C
385 -220 to 400 °C
392 -180 to 400 °C
-70 to 300 °C
-70 to 300 °C
1000 ohm Ni. -60 to 209 °C
FREQUENCY:
2 or 4 channels 0 to 5000Hz all channels (0 to 10,000Hz 1 channel alone). Input on
channels 1, 6, 7 and 12 only.
Accuracy: +1Hz
Page 100
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A - Technical Specifications
RECORDING
Recording Rates
Data Format
User programmable from 10 samples per second to 1 sample every 99 hours.
Proprietary encrypted format. User File naming.
Data Storage Capacity
Data stored in non-volatile RAM and recorded automatically to
Removable Media Types Industry Standard removable Compact Flash to 2GB
Industry Standard USB Flash Drives to 2 GB
Internal Media
File types
Industry Standard SD card (internal memory) to 1GB
Data files, Alarm and Event files, Configuration files, Language Files, Multiple files of
different names on a single disk.
COMMUNICATIONS
Network
10/100 Base T Ethernet per 802.3. RJ45 Connection standard
Webserver supports http and ftp protocols
OPC server
Servers
Modbus Over Ethernet Server
Serial (Option)
Isolated RS485/RS232 Modbus Interface
INPUT / OUTPUT OPTION
Outputs
Optional: Up to 12 x Relay out Form A (normally open SPST contacts) rated at 200Vdc
Current :0.5A Max Power: 10 watt MAX
Inputs
Up to 6 optically isolated inputs
DESIGN ATTRIBUTES
Operating Range
Protection
Safety
0°C to 50°C, 10% to 80% RH
IP65 when mounted in panel
Meets the requirements of UL-3111-1 and EN61010- 1 when installed in accordance with
the instruction in the manual.
UL and cUL approved – Pending
Other
21CFR11 compliant
EMC
Meets the requirements of EN61326:1998 and CE directive 89/336/EEC
100 to 240 Vac, 50/60 Hz or 125 Vdc @ 35VA max.
Input Voltage
PHYSICAL PARAMETERS
Dimensions
174mm D x 144mm H x 144mm W (excluding rear connections)
Weight
Approx. 2.5kg (5.6lbs) - weight will vary depending on options installed
Page 101
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B – Digital Input Voltage Adjustment
APPENDIX B – DIGITAL INPUT VOLTAGE ADJUSTMENT
WARNING
TO ELIMINATE THE RISK OF SHOCK ENSURE THAT THE MAINS CABLE AND ALL
CONNECTORS ARE REMOVED FROM THE RECORDER BEFORE PROCEEDING.
B.1 ANALOG MODULE:
The analog input module accepts frequency inputs
on Channels 1, 6, 7 and 12. By default these inputs
are set up to accept input voltages from 12 to 24
volts dc. The user can change the input voltage
range to 5 to 12 volts dc by moving jumpers
internally on the module. This involves removing the
ANALOG MODULE
analog module from the recorder.
A
B
A
To do this, remove the screws marked A in Figure
B-1 and gently pull the module from the enclosure.
Once the module is removed, identify the jumpers
as shown in Fig B-2. Note that 6 channel units will
not have the daughter board sitting on top of the
main board. The jumper locations are as follows:
DIGITAL IO MODULE
B
Bottom Board: P4 – Channel 6; P5 – Channel 1
Top Board (if present): P4 – Channel 12; P5 –
Channel 7
Fig B-3 shows the jumper detail. Jumpers are
shown in position 2-3. The links are as follow:
Fig B-1 Recorder Rear Panel
Position 2 - 3
12 to 24Vdc Input (default)
5 to 12Vdc Input
Position 1 – 2
Set the jumpers as required and reinstall the module
into the recorder chassis. Take care to align the
connector with the socket before applying pressure
to the module. Replace the screws.
Fig B-2 Analog Module
Fig B-3 Analog Module Jumpers
Page 102
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B – Digital Input Voltage Adjustment
B.2 DIGITAL IO MODULE:
The digital IO module accepts 2 to 6 digital inputs depending on options. By default these inputs are set up to
accept input voltages from 12 to 24 volts dc. The user can change the input voltage range to 5 to 12 volts dc
by moving jumpers internally on the module. This involves removing the digital IO module from the recorder.
To do this, remove the screws marked B in Figure B-1 and gently pull the module from the enclosure. Note
that the rear panel is loose and not connected to the circuit board.
Once the module is removed, identify the jumpers as shown in Fig B-4. Note that there could be up to 6
jumpers present. The jumper locations are as follows:
2 Input Board:
P2 – Input 1; P3 – Input 2
Jumpers correspond to inputs from
right to left when looking at the
terminal block side of the board.
Jumpers are shown in position 1-2.
The links are as follow:
Position 2–3 12 to 24Vdc Input
Position 1–2
5 to 12Vdc Input
Set the jumpers as required and
reinstall the board into the recorder
chassis. Take care to align the
connector with the socket before
applying pressure to the board.
Replace the panel and the screws.
Fig B-4 Digital IO Module Jumpers (2 Channel shown)
Page 103
09/11/2008 REV 0.99
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in m aterials and workm anship for a
period of 25 m onths from date of purchase. OMEGA Warranty adds an additional one (1) m onth grace
period to the norm al tw o (2) years product w arranty to cover handling and shipping tim e. This
ensures that OMEGA’s custom ers receive m axim um coverage on each product.
If the unit m alfunctions, it m ust be returned to the factory for evaluation. OMEGA’s Custom er Service
Departm ent will issue an Authorized Return (AR) num ber im m ediately upon phone or written request.
Upon exam ination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not lim ited to m ishandling, im proper interfacing, operation outside of design lim its,
im proper repair, or unauthorized m odification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corro-
sion; or current, heat, m oisture or vibration; im proper specification; m isapplication; m isuse or other op-
erating conditions outside of OMEGA’s control. Com ponents which wear are not warranted, including
but not lim ited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. How ever,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages
that result from the use of its products in accordance with information provided by OMEGA, either verbal or
written. OMEGA warrants only that the parts manufactured by it will be as specified and free of defects.
OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EX-
PRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WAR-
RANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict
liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In
no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipm ent sold by OMEGA is not intended to be used, nor shall it be used: (1) as a
“Basic Com ponent” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in
m edical applications or used on hum ans. Should any Product(s) be used in or with any nuclear
installation or activity, m edical application, used on hum ans, or m isused in any way, OMEGA assum es
no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally,
purchaser will indem nify OMEGA and hold OMEGA harm less from any liability or dam age whatsoever
arising out of the use of the Product(s) in such a m anner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Custom er Service Departm ent.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED
RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR num ber should then be m arked on the outside of the return
package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to
FOR WARRANTY RETURNS, please have the
following inform ation available BEFORE
contacting OMEGA:
FOR NON-WARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following infor-
m ation available BEFORE contacting OMEGA:
1. Purchase Order number under which the prod
uct was PURCHASED,
1. Purchase Order num ber to cover the COST
of the repair,
2. Model and serial num ber of the product under
warranty, and
3. Repair instructions and/or specific problem s
relative to the product.
2. Model and serial num ber of the product, and
3. Repair instructions and/or specific problem s
relative to the product.
OMEGA’s policy is to m ake running changes, not m odel changes, whenever an im provem ent is possible. This affords our
custom ers the latest in technology and engineering.
OMEGA is a registered tradem ark of OMEGA ENGINEERING, INC.
© Copyright 1998 OMEGA ENGINEERING, INC. All rights reserved. This docum ent m ay not be copied, photocopied, repro-
duced, translated, or reduced to any electronic m edium or m achine-readable form , in whole or in part, without the prior
written consent of OMEGA ENGINEERING, INC.
Download from Www.Somanuals.com. All Manuals Search And Download.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at www.omega.com
TEMPERATURE
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
pH/CONDUCTIVITY
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters
HEATERS
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Ⅺ
ߜ Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
M-4698/0908
Download from Www.Somanuals.com. All Manuals Search And Download.
|