INSTRUCTION
MANUAL
Eat well, drink well and live well with Omega
OFS20 & OFS30
GRANITA MACHINE
English
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
OMGMAN 082009 RevA
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Specifications
3
Instructions for Machine Transport
Installation
4
4
Operating & Cleaning Procedures
Exploded View
5
8
Parts List
9-10
11
12
Electrical Diagram
Warranty
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
OFS30
OFS20
OFS20
OFS20 Power Requirements:
Volts: 120/240VAC
Amps: 6 A/3 A
Dimensions: H 23in x W 17in x D 16in
H 59cm x W 41cm x D 43cm
Watts: 710
Hz: 50/60
OFS30
OFS30 Power Requirements:
Volts: 120/240VAC
Amps: 8 A/4 A
Dimensions H 23in x W 17in x D 24in
H 59cm x W 41cm x D 61cm
Watts: 980
Hz: 50/60
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Instructions for Machine Transport
NOTE: Refrigeration equipment must remain upright to avoid damage to
the compressor In order to prevent the oil contained in the compressor
from flowing into the cooling circuit, it is necessary to always ship, carry,
store and handle this Granita machine in an upright position, following
the instructions located on the packaging. Never ship, carry, store or
handle unit on its side.
Installation
1.) Cut banding straps from box and lift the box off the machine (see fig. 1).
2.) Positioning the machine
The machine must be well ventilated. Leave an 8” (20 cm) clearance on the sides
and back of the machine to allow proper ventilation. Installation of the machine
near a heat source should be avoided. Some heat sources you should avoid locating
this unit too close to are ovens, coffee machines, cold or frozen beverage dispensers
or ice machines (equipment with compressors that expel hot air through its vents. An
ambient temperature between 59°F (15°C) and 77°F (25°C) is recommended.
Connection to Main Power Supply
• The electrical safety of this Granita machine can only be achieved if the ma-
chine is properly connected to an appropriate grounded receptacle that is in com-
pliance with current national safety standards. Therefore, the manufacturer cannot
be held responsible for damage and/or injury caused by failure to connect the unit
to an appropriate power source.
• For a safe and correct installation, connect the unit to a dedicated outlet.
• Do not alter the cord or plug in any way.
• The entire length of the power supply cord must not, in any way, be com
pressed (bent or bunched together) nor may extension cords be used.
• Do not obstruct the ventilation and heat dispersion grill vents on the side and
rear panels of the unit. An insufficient ventilation process may reduce the efficiency
of the machine, causing it to function inadequately, and cause serious damage to
the machine. A minimum of eight inches (20cm) clearance is necessary on each side
and behind the unit.
WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED TO AVOID POSSIBLE
FATAL ELECTRICAL SHOCK OR SERIOUS INJURY TO THE OPERATOR. THE POWER CORD IS
PROVIDED WITH A THREE PRONG GROUNDED PLUG. IF A THREE-HOLE GROUNDED
ELECTRICAL OUTLET IS NOT AVAILABLE, USE AN APPROVED METHOD TO GROUND THE
UNIT. DO NOT USE EXTENSION CORDS WITH THIS UNIT. DO NOT “GANG” TOGETHER
WITH OTHER ELECTRICAL DEVICES ON THE SAME OUTLET.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Procedure
Left - Right Middle Bowl Switches:
Each switch corresponds to the number and location of the bowls config-
uration to the dispenser. When the switch is in the up/on position the motor
and cooling will be turned on.
Care and Cleaning
Preparing Product
Attention: Make sure that the mixture has a 13% - 15% minimum Brix (sugar
content). A lower concentrate could seriously damage the mixing parts,
as well as the gear motors. NEVER USE ONLY WATER.
1. If using product concentrate (instead of ready-to-use product), dilute
and mix the product with water, according to the directions given by the
manufacturer, in a separate container. Never pour dry powder, crystals, or
concentrate into a dry bowl.
2. Remove the merchandising lid. Pour the prepared product into the
bowl. Do not spill any material on lid or on bowl. There is a minimum and
maximum fill line on the bowl. Do not overfill or run the unit without
enough product. Running unit with product below the minimum full line
may cause damage to the unit. Insert the plug into a dedicated electrical
outlet.
Dispensing
Product
To dispense the product, position the cup
under the dispensing valve and lower the
dispensing lever.
NOTE: If the machine is turned off at night, with the bowls filled, or just partially filled, a layer of
solid ice may form on the surface due to the natural separation of the unmixed (non-moving)
product. In this case, before turning the machine back on, remove the layer of superficial ice
to prevent damage to the spiral agitator.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjustments
Consistency Adjustment:
1. Unplug the machine.
2. Be sure that product in the bowl is within proper fill range.
(Above the minimum fill line) Remove merchandiser.
3. Change the thickness of the product by turning the screw on the
back of the bowl, as shown on fig. Turn the screw clockwise for thinner
product or counterclockwise for thicker product, (+) thicker, (-) thinner.
Each bowl has its own adjusting screw.
Cleaning Procedures
Disconnect the unit from the power supply before sanitizing and cleaning.
Failure to do so may result in electric shock.
Daily Cleaning: For the machine to function properly, it is important that
the cleaning procedures be carried out daily, according to the following
instructions:
Turn off the equipment and empty the bowl of its remaining product. After
draining the product from the unit, you can fill the bowl with hot water
(not boiling) to help melt off any sugar deposits. Drain the water prior to
proceeding to the next step. To disassemble the draw valve, extract the
pin from its seat and the rest of the parts will come out. Wash them with
care in warm water.
Remove the bowl by lifting the front part until released, then gently hit on
the rear side to completely remove it. Take off the bowl, the spiral agitator
and the rear gasket.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before replacing the spiral agitator put gaskets in their seats and lubricate
them with the supplied food grade lubricant. Insert the spiral agitator and
place back the bowl in its seat. Lightly lift the front part of the spiral agita-
tor until it corresponds to point D. The bowl and the spiral will join. Push the
bowl down until you hear a click and replace the tap.
Do not put in dishwasher. Dishwasher may damage some parts such as
the clear plastic auger gears and top mixing bar. Reassemble with clean
hands.
Maintenance
Warning: Disconnect the unit from its power supply prior to performing any
maintenance procedures. Failure to do so could result in electric shock,
injury from hazardous moving parts or serious burns from hot surfaces.
Removing and cleaning
the filter (Weekly)
Cleaning the
Condenser (Monthly)
Failure to maintain a clean filter and condenser will cause damage to the
unit not covered by warranty.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED VIEW & PARTS LIST
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Serial No.
Part No.
Description
1
2
PSH-GL1000-4
PSH-GL1002-5
PSH-GL1002-4
PSH-GL1005
Condenser
Compressor-OFS20
Compressor-OFS30
Evaporator
3
4
PSH-GL1006
Filter Dryer
5
PSH-GL1007
Gas Valve
6
PSH-GL1009-UL
PSH-GL1009
Coil for Gas Valve 110V (UL)
Coil for Gas Valve 220V
High Air Pressure Valve
Low Air Pressure Valve
Fitting-OFS20
7
8
PSH-GL1012
9
PSH-GL1013
10
PSH-GL1015-1
PSH-GL1015-2
PSH-GL1015-3
PSH-GL1515-4
PSH-GL1016-1-UL
PSH-GL1017
Fitting-OFS20
Fitting-OFS30
Fitting-OFS30
11
12
13
14
15
16
17
18
19
20
21
22
23
24
31
32
33
34
35
39
40
Fan Motor 110V (UL)
Fan Blades
PSH-GL2000
Drive Spindle for Spiral
C Ferrule
PSH-GL2001
PSH-GL2002
Bushing
PSH-GL2003
Drive Spindle for Spiral
Scraper for Spiral
Spiral Section
PSH-GL2004
PSH-GL2005
PSH-GL2006
Clip for Attaching Scraper
Gear Box
PSH-GL2007
PSH-GL2008
Box Cap
PSH-GL2009
Seal
PSH-GL2010-1
PSH-GL2011-1
PSH-GL2028
Stirring Motor + Coil
Coil
Bushing for Hardness Control Pin
Hardness Control Catch
Hardness Control Screw
Twisted Spring
PSH-GL2029
PSH-GL2030
PSH-GL3000
PSH-GL3001
Light Bulb Assembly
PC-Board
PSH-GL3005
PSH-GL4000-2-UL
PSH-GL4000-3-UL
PSH-GL4001-1-BLK
PSH-GL4003-BLK
PSH-GL4004-2-UL
PSH-GL4004-3-UL
PSH-GL4005-2
Front Metal Panel OFS20
Front Metal Panel OFS30
Side Panel-Left (Black)
Side Panel-Right (Black)
Back Metal Panel OFS20
Back Metal Panel OFS30
Frame OFS20
41
42
43
44
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Serial No.
Part No.
Description
PSH-GL4005-3
PSH-GL4006-BLK
PSH-GL4007
PSH-GL4008
PSH-GL4009
PSH-GL4010
PSH-GL4011
PSH-GL4012
PSH-GL4013
PSH-GL4014
PSH-GL4015
PSH-GL4016
PSH-GL4017
PSH-GL4018
PSH-GL4019
PSH-GL5036
PSH-GL4021-2-UL
PSH-GL4022
PSH-GL4023-BLK
PSH-GL4028-UL
PSH-GL1018-1
PSH-GL3006-1-UL
PSH-GL3007
PSH-GL3008
PSH-GL3009-3
PSH-GL3009-4
PSH-GL3010
PSH-GL4029
PSH-GL5006
PSH-GL5007
PSH-GL5034-UL
Frame OFS30
45
46
47
48
49
50
51
52
53
54
55
56
57
58
Plastic Holder (Black)
Pin
Power Switch
Motor Select Switch
PC Bowl
PC Bowl Cap
Artwork Plate
Handle (Tap)
Pin (Tap)
Piston
O-Ring
Spring
Seal (Bowl)
Fixed Evaporator Set & Cap
Fixed Evaporator Cover
Support Feet UL
Cover for PC Board
Drip Tray (Black)
Power Cord UL
Subsidiary Fan Motor UL
Transformer UL
Gasket
59
60
61
62
63
64
65
66
67
Bushing
Protective Switch 20A OFS20
Protective Switch 30A OFS30
Terminals Connectors Set
Positioning Ring
Power Box
68
69
70
71
72
Bracket
Power Cord UL
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electric Circuit Diagram OFS30
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty:
One (1) Year Parts and Labor
OMEGA and Asbury Service Warranty & Parts (ASW&P) warrants to the
original purchaser of the OMEGA Granita Dispenser and all parts thereof
to be free from defects in material and workmanship while under normal
use and service as indicated by the OMEGA installation and operating
instructions for a period of one (1) year from the date of installation (war-
ranty registration must be filed within 10 days of installation for warranty
to be activated). OMEGA’s obligation under this warranty shall be lim-
ited to repairing or replacing, including parts and labor, Monday thru Fri-
day from 8:00a.m. to 5:00p.m. excluding holidays and weekends and
reasonable travel not to exceed two (2) hours or one hundred (100)
miles round trip, any part or assembly of such product which proves to
be defective and which upon examination by an ASW&P authorized
service technician shall disclose to our satisfaction to be defective. Nei-
ther Omega nor Asbury Service Warranty & Parts shall be held responsi-
ble for spoilage of products, loss of sales or consequential damages.
Any after hours, premium or emergency service must have ASW&P’s
authorization prior to having service dispatched or a claim filed for
warranty consideration. Other conditions and limitations may apply and
can be found on the back of the warranty registration card (supplied
separately).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Omega Products, Inc · Harrisburg, PA 17111-4523, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Phone:(717) 561-1105 · Fax:(717) 561-1298
|