RangeMax Wireless-N
150 Router Setup Manual
NETGEAR, Inc.
350 E. Plumeria Drive
San Jose, CA 95134 USA
November 2009
208-10541-01
v1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Getting to Know Your Wireless Router................................................................................1
Unpacking Your New Router .............................................................................................1
What You Need Before You Begin ....................................................................................6
Updating Your Router Firmware ........................................................................................6
Two Setup Methods: Smart Wizard Setup or Manual Setup .............................................7
Smart Wizard Setup ..........................................................................................................7
Manual Setup ....................................................................................................................8
Product Registration, Support, and Documentation ........................................................13
Setting Up and Testing Basic Wireless Connectivity .......................................................16
Implementing Appropriate Wireless Security ...................................................................17
Help with Troubleshooting..................................................................................................18
Basic Troubleshooting .....................................................................................................18
Troubleshooting Connectivity Using the Ping Utility ........................................................24
Technical Specifications.....................................................................................................27
Factory Default Settings ..................................................................................................27
Related Documents .............................................................................................................30
Contents
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting to Know Your Wireless Router
Congratulations on your purchase of a NETGEAR® high-speed wireless router, the RangeMax
Wireless-N 150 Router Model WPN824N.
Before you begin installing your router, check the package contents (see Unpacking Your New
Router). Become familiar with the front and back panels of your router—especially the status
Unpacking Your New Router
The product package should contain the following items:
•
•
•
•
•
•
The wireless router
A snap-on stand for your wireless router
An AC power adapter (varies by region)
A yellow Ethernet cable
NETGEAR Installation Guide
The Resource CD, which includes:
–
–
–
The Smart Wizard Installation Assistant (Autorun.exe)
A PDF version of this manual
A link to the online User Manual
•
Warranty and Support Information cards
If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the
carton, including the original packing materials, in case you need to return the product for repair.
To prepare your router for installation:
1. Carefully peel off the protective film covering the sides of your router.
Getting to Know Your Wireless Router
1
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
2. Set up your wireless router by inserting the router into the stand supplied with your router.
Figure 1
3. Place your router in an area suitable for installation (near an AC power outlet and accessible to
the Ethernet cables for your wired computers).
Getting to Know Your Wireless Router
v1.0, November 2009
2
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Router Front Panel
Figure 2
You can use the status lights on the front of the wireless router to verify various conditions.
Table 1-1. Status Light Descriptions
Item Function Activity
Description
Power
On green solid
Power is supplied to the router.
1
Off
Power is not supplied to the router.
Test
On
The unit is performing the power-on self-test diagnostic.
Off
The unit successfully completed the power-on self-test diagnostic.
2
Slow blinking
The reset button is being pushed, restoring the factory default
settings.
Wireless On
Off
The wireless interface is enabled.
The wireless interface is turned off.
3
Blinking
Data is being communicated over the wireless network.
Internet
Amber off
No Ethernet cable is connected to the modem.
Amber on
The Ethernet cable connection to the modem is good.
Amber blinking
Packets are being transmitted and received from a modem or other
network device, but no IP address has been received.
4
5
No IP address has been received.
Green off
On
IP address has been received.
IP address received and data is being transmitted and received.
Blinking
LAN
Green
Amber
The LAN port has detected a 100 Mbps link with an attached device.
The LAN port has detected a 10 Mbps link with an attached device.
Getting to Know Your Wireless Router
v1.0, November 2009
3
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Router Back Panel
The rear panel of the WPN824N router contains the items in the list that follows the figure.
5
6
4
1
2
3
Figure 3
The back of the wireless router includes:
1. AC power adapter outlet
2. Power On/Off switch
3. Four local (LAN) 10/100 Mbps Ethernet ports for connecting the router to the local computers
4. Internet (WAN) Ethernet port for connecting the router to a cable or DSL modem
5. Wireless On/Off button
6. Factory default reset button
Getting to Know Your Wireless Router
v1.0, November 2009
4
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Top Panel
Figure 4
The top of the wireless router includes a dome with status lights that identify the status of the
selected option you chose for either Wireless data status (default), Guest Network status, Live
Parental Controls status, or Broadband Usage Meter status. These status lights are on by default,
but can be turned off by clicking the Dome, or by going to the Network Monitor Display Settings
Bottom Label
View the label on the bottom of the wireless router to identify the serial number, port connectors,
status lights, and default login information.
Figure 5
Getting to Know Your Wireless Router
v1.0, November 2009
5
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
What You Need Before You Begin
Prepare the following before you set up your Product Family:
•
•
Internet service.
The configuration information your Internet Service Provider (ISP) gave you. Depending on
how your Internet account was set up, you might need one or more of these settings for the
wireless router to access the Internet:
— Host and domain names
— Internet login name and password (frequently an e-mail address and password)
— Domain Name Server (DNS) addresses
— Fixed or static IP address
Your ISP should have provided you with all the information needed to connect to the Internet.
If you cannot locate this information, you can ask your ISP to provide it.
•
For cable modem service, use the computer you first used to set up your Internet service.
Updating Your Router Firmware
NETGEAR is always improving the operability and features included with your router. To make it
easy for you to receive the best, most up-to-date features of your router, NETGEAR provides a
variety of methods for updating your product.
•
The Smart Wizard installation assistant lets you check for and install updates as part of the
setup activity.
•
The router includes an update feature that lets you check for and install updates. You must be
logged in to the router to use this feature.
These options are discussed in “Accessing the Wireless Router after Installation and Checking for
Getting to Know Your Wireless Router
v1.0, November 2009
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Two Setup Methods: Smart Wizard Setup or Manual
Setup
You have two methods available for setting up your wireless router:
•
Smart Wizard Setup.This option is the easiest. The wizard guides you through the setup
process, automates many of the steps, and verifies that necessary conditions exist and that
steps you perform have been successfully completed. This option requires a PC running
Microsoft Windows.
•
Manual Setup. This option is best if you cannot use the wizard on the CD, are replacing an
existing wireless router, or are technically knowledgeable. Follow the instructions in this
manual to set up your wireless router.
Use the setup option that best suites you.
Smart Wizard Setup
The wizard setup process takes about 20 minutes to complete.
1. Insert the NETGEAR CD into a Windows PC. The CD automatically starts and detects the
language you are using on your PC. Accept the language option, or change to a different
language.
If the CD does not automatically start, browse the CD and double-click Autorun. Be
sure to double-click the Autorun file that begins with an upper-case A.
2. When the Welcome screen displays, click Setup to start the Smart Wizard. Follow the wizard
instructions.
Getting to Know Your Wireless Router
v1.0, November 2009
7
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Manual Setup
There are two steps to setting up your wireless router:
1. Connect the Product Family to the ADSL or cable modem, and connect a computer to the
Product Family.
Your computer has to be set to automatically get its TCP/IP network settings from
the Product Family through DHCP. This is usually the case. If your are unsure about
this, use the wizard on the CD, which automatically takes care of this for you, or
refer to the documentation for your computer.
2. Configure the Product Family to use your Internet service.
Connecting Your Wireless Router
To connect your wireless router:
1. Connect the wireless router, the computer, and the modem.
a. Turn off your computer.
b. Turn off and unplug the cable or ADSL broadband modem.
c. Locate the Ethernet cable (1) that connects your computer to the modem.
1
2
Figure 6
d. Disconnect the cable at the modem (2). You will connect it to the router later.
Getting to Know Your Wireless Router
v1.0, November 2009
8
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
e. Use the label on the bottom of the wireless router to locate the Internet port, which is to the
left of the Wireless On/Off button on your router.
f. Locate the Ethernet cable that came with the NETGEAR product. Securely insert that
Ethernet cable into your modem and into the Internet port of the wireless router (3).
3
Figure 7
into a LAN port on the router such as LAN port 1.
4
Figure 8
Your network cables are connected, and you are ready to start your network.
2. Start your network in the correct sequence.
Failure to start or restart your network in the correct sequence could prevent you
from accessing the Internet.
a. First, plug in and turn on the cable or DSL modem. Wait 2 minutes.
b. Now, plug the power cord into your wireless router and into a power outlet. Wait 1 minute.
Getting to Know Your Wireless Router
v1.0, November 2009
9
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
c. Last, turn on your computer.
For DSL customers, if software logs you in to the Internet, do not run that
software. You might need to go to the Internet Explorer Tools menu, Internet
Options, then click the Connections tab where you can select Never dial a
connection.
d.
Figure 9
e. Check the wireless router status lights to verify the following:
•
•
Test: The test light (2) blinks when the router is first turned on, then goes off. If after 2
•
•
Wireless. The wireless light (3) should be on.
Internet: The Internet port light (4) should be lit. If it is not, make sure that the
Ethernet cable is securely attached to the wireless router Internet port and that the
modem, and the modem is powered on.
•
LAN. A LAN light (5) should be lit. Green indicates that your computer is
communicating at 100 Mbps; amber indicates 10 Mbps. If a LAN light is not lit, check
that the Ethernet cable from the computer to the router is securely attached at both
ends, and that the computer is turned on.
Getting to Know Your Wireless Router
v1.0, November 2009
10
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
your browser, and then click Enter.
Figure 10
Connect to the wireless router by typing any one of these three URLs in the address
field of your browser, then clicking Enter:
A login window like the one in the following figure opens:
Figure 11
4. For security reasons, the router has its own user name and password. When prompted, enter
admin for the router user name and password for the router password, both in lower case
letters.
The router user name and password should not be confused with any user name or
password you may use to log in to your Internet connection.
Getting to Know Your Wireless Router
v1.0, November 2009
11
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
After logging in, if you see a window with a message about firmware upgrades, click Close
Window.
On the left, click Setup Wizard to view the following screen.
Figure 12
If you cannot connect to the wireless router, verify your computer networking setup. It should
be set to obtain both IP and DNS server addresses automatically, which is usually the case. For
help with this, consult the documentation that came with your computer, or see the links
5. Click Next. The wizard assists you with configuring your wireless router to access the
Internet.
Advanced users who want to manually configure the router can select the No radio button,
enter admin and password as the user name and password when prompted, and fill in the
required information on the Basic Settings page (for more information about basic settings,
6. Click Done to finish.
You are now connected to the Internet! The wireless router displays its home page.
If you do not click Logout, the wireless router waits 5 minutes after there is no activity before it
automatically logs you out.
Getting to Know Your Wireless Router
v1.0, November 2009
12
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Product Registration, Support, and Documentation
can use NETGEAR’s telephone support service. Product updates and Web support are always
Documentation is available on the CD, on the support website, and on the documentation website.
When the wireless router is connected to the Internet, click the Knowledge Base or the
Documentation link under Web Support to view support information or the documentation for the
wireless router.
Accessing the Wireless Router after Installation and
Checking for New Firmware
The Smart Wizard appears only when you first install the router or when the router is in its factory
default state (for example, if you have reset the router to its factory default settings). If you want to
change the settings after installing and configuring your router using the Smart Wizard, you must
open a browser window and log in to the router.
The factory default state is restored when you use the factory reset button. See “How
information about this feature.
To access the router using its login name and password:
your browser, and then click Enter.
Figure 13
You can connect to the wireless router by typing any one of these three URLs in
the address field of your browser, then clicking Enter:
Getting to Know Your Wireless Router
v1.0, November 2009
13
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
2. For security reasons, the router has its own user name and password. When prompted, enter
admin for the router user name and password for the router password, both in lower case
letters.
The router user name and password should not be confused with any user name or
password you may use to log in to your Internet connection.
A login window like the one in the following figure opens:
Figure 14
Enter the user name and password.
To update your router firmware:
1. If the Router Upgrade screen does not display automatically, select Router Upgrade under
Maintenance on the main menu. The Router Upgrade screen displays.
2. Click Browse, and locate the unzipped firmware image that you downloaded to your PC (the
file ends in .img).
Getting to Know Your Wireless Router
v1.0, November 2009
14
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
3. Once you have selected the file, click Upload to send the software to the router. The upload
process takes several minutes. When the software upload process is complete, the router
restarts.
Do not try to go online, turn off the router, shut down the computer, or do
anything else to the router until the router finishes restarting! When the Test
light stops blinking, wait a few seconds more before using the router.
4. After the router has restarted, select Router Status under the Maintenance heading. Check the
firmware version to verify that your router now has the new software installed.
If you are unable to successfully upgrade using this method, refer to the online Reference
Manual available through the Documentation link on the router main menu (or through a link
on the Resource CD) for other ways to upgrade the router.
If you selected the No radio button during installation, and want to check for new firmware later,
use the following procedure. Determine the firmware version currently running on your router
before you check for updates on the NETGEAR website. Then go to the NETGEAR website and
select the model number for this router. If a later version of the firmware is available, upload the
firmware to your computer, and upgrade your router.
To manually check for new router firmware:
browser. Press Enter.
2. When prompted, enter the default user name and password (admin for the router user name
and password for the router password), both in lowercase letters. If you changed the user
name and password from the defaults, then enter your new user name and password.
3. Select Router Status under Maintenance on the router menu. When the Router Status screen
displays, note the version number of your router firmware.
5. From the Product Selection drop-down list, select your router model number. The Product
Support page for your router displays.
6. Under Downloads, check the most recent firmware version offered against the firmware
version shown on the Router Status screen.
7. If the version on the NETGEAR website is more recent, click on its version number, then click
Right-click and Save to Download and save the file to a location on your hard disk.
Getting to Know Your Wireless Router
v1.0, November 2009
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
8. Follow the procedure in “To update your router firmware:” on page 14 to complete the
upgrade process.
Setting Up and Testing Basic Wireless Connectivity
Follow these instructions to set up and test basic wireless connectivity. Once you have established
basic wireless connectivity, you can enable security settings appropriate to your needs.
To set up and test basic wireless connectivity:
Variable with the default user name of admin and default password of password, or using
whatever LAN address and password you have set up.
2. Click Wireless Settings in the main menu bar of the wireless router.
3. Note that the default SSID is NETGEAR.
The SSID of any wireless adapters must match the SSID you configure in the
wireless router. If they do not match, you will not get a wireless connection.
4. Set the region, selecting the region in which the wireless interface will operate.
5. To save your changes, click Apply.
If you are configuring the Product Family from a wireless computer and you change
the Product Family’s SSID, channel, or security settings, you will lose your
wireless connection when you click Apply. You must then change the wireless
settings of your computer to match the Product Family’s new settings.
6. Configure and test your computers for wireless connectivity.
Program the wireless adapter of your computers to have the same wireless network name
(SSID) as the wireless router. Check that they have a wireless link and are able to obtain an IP
address by DHCP from the Product Family.
Getting to Know Your Wireless Router
v1.0, November 2009
16
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router WPN824N Setup Manual
Implementing Appropriate Wireless Security
Indoors, computers can connect over 802.11g or 802.11n wireless networks at a range
of over 300 feet. Such distances can allow for others outside of your immediate area to
access your network.
Unlike wired network data, your wireless data transmissions can extend beyond your walls and
can be received by anyone with a compatible adapter. For this reason, use the security features of
your wireless equipment. The wireless router provides highly effective security features, which are
covered in detail in the full reference manual that is available from a link on the CD as well as a
link in the main menu of your Product Family. Follow the instructions in the full manual and in the
Product Family help screens to implement the security features appropriate to your needs.
Getting to Know Your Wireless Router
v1.0, November 2009
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Help with Troubleshooting
This chapter gives information about troubleshooting your wireless router. You will find help with
the following problems:
•
Basic troubleshooting
•
Advanced connectivity troubleshooting using the PING utility
Basic Troubleshooting
Here are some tips for correcting simple problems you might have.
Common Things That Can Go Wrong
Verify that you do not have these common problems.
Be sure to always start your network in this sequence:
1. Turn off and unplug the modem from it’s power outlet, and turn off the wireless router and
computer.
2. Turn on the modem, and wait 2 minutes.
3. Turn on the wireless router, and wait 1 minute.
4. Turn on the computer.
Help with Troubleshooting
18
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Make sure that the Ethernet cables are securely plugged in:
1. Verify that the Internet status light on the wireless router will be lit if the Ethernet cable to the
wireless router from the modem is plugged in securely and the modem and wireless router are
2. Verify that for each powered-on computer connected to the wireless router with a securely
plugged in Ethernet cable, the corresponding wireless router LAN port status light is lit (see
“Router Front Panel” on page 3). The label on the bottom of the wireless router identifies the
Make sure that the network settings of the computer are correct:
1. Verify that your LAN connected computers are configured to obtain an IP address
automatically through DHCP. For help with this, see the documentation for your computer or
2. Verify whether the MAC address is needed. Some cable modem services require you to use
the MAC address of the computer registered on the account. If so, in the Router MAC Address
section of the Basic Settings menu, select Use this Computer’s MAC Address. To save your
settings, click Apply. Restart the network in the correct sequence.
Check the router status lights to verify correct router operation:
If the Power light does not turn solid green within 2 minutes after you turn the router on, reset the
Basic Functions Are Not Working
After you turn on power to the router, check these status lights:
1. When power is first applied, verify that the Power light is on.
a. Make sure that the power cord is properly connected to your router and that the power
supply adapter is properly connected to a functioning power outlet.
b. Check that you are using the power adapter supplied by NETGEAR for this product.
If the error persists, you have a hardware problem and should contact technical support.
2. Verify that the Test light lights within a few seconds, indicating that the self-test procedure is
running.
Help with Troubleshooting
19
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
3. After approximately 20 seconds, verify that:
a. The Test light turned off.
b. The LAN port lights are lit for any local ports that are connected.
c. The Internet port is connected and its light is lit.
If a port’s light is lit, a link has been established to the connected device. If a LAN port is
connected to a 100 Mbps device, verify that the port’s light is green. If the port is 10 Mbps, the
light is amber.
Verify whether the Test light never turns on or stays on:
1. Verify that when the router is turned on, the Test light turns on for about 20 seconds and then
turns off. If the Test light does not turn on or stays on, the router has a problem.
2. Turn the power off and then on to see if the router recovers. If all lights including the Test light
are still on one minute after powering up:
a. Turn the power off and back on to see if the router recovers.
b. Clear the router’s configuration to factory defaults. This sets the router’s IP address to
192.168.1.1. This procedure is explained in “How Do I Restore the Default Password and
If the error persists, you might have a hardware problem and should contact technical support.
Verify if the LAN or Internet port lights are not on when the Ethernet connection is made:
1. Make sure that the Ethernet cable connections are secure at the router and at the computer.
2. Make sure that power is turned on to the connected computer.
3. Make sure that you are using Ethernet cables like the cable that was supplied with the wireless
router.
I Am Unable to Log In to the Wireless Router
If you are unable to log in to the wireless router, check the following:
•
If you are using an Ethernet-connected computer, check the Ethernet connection between the
computer and the router as described in the previous section.
Help with Troubleshooting
20
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
•
•
Make sure that you are using the correct login information. The factory default login name is
admin, and the password is password. Make sure that Caps Lock is off when you enter this
information.
Typically, your computer’s address should be in the range of 192.168.1.2 to 192.168.1.254.
Refer to your computer’s documentation for help with finding your computer’s IP address.
If your computer’s IP address is 169.254.x.x, verify that you have a good
connection from the computer to the router, and then restart your computer.
•
Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using
Internet Explorer, click Refresh to be sure that the Java applet is loaded. Try closing the
browser and starting it again.
The Internet Service Connection Is Not Working
If your router is unable to access the Internet, check that the Internet connection is working, and
then check that the wireless router can get an Internet address.
Check that the Internet connection is working:
1. Internet connection. First verify that your cable or ADSL modem has a successful
connection. The cable or ADSL modem status lights indicate if the modem connection is
successful or not. Check your modem documentation, or call your Internet service provider for
help with verifying that the modem has a successful connection.
2. Wireless router Internet light is green or blinking green. If your Internet light is green or
blinking green, then you have a good Internet connection, and your wiring is correct.
3. Wireless router Internet light blinking amber. If your Internet light is blinking amber, then
your wireless router is attempting to make an Internet connection with the service provider.
The LED should turn green within several minutes. If it does not, check the Internet
connection on the modem as described above.
4. Wireless router Internet light off. If the Internet light is off, verify that the Ethernet cable is
securely connected between the cable or ADSL modem, and that both the modem and wireless
router are turned on.
Help with Troubleshooting
21
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Obtaining an Internet IP Address
If your wireless router is unable to access the Internet, and your Internet light is amber or blinking
amber, check the wireless router to see if it is able to get an Internet IP address from your service
provider. Unless you have a static IP address, your wireless router automatically requests an IP
address from your service provider.
To check the Internet IP address from the browser interface:
1. Log in to the wireless router.
2. Use the Router Status link under the Maintenance heading to check that an IP address is shown
for the Internet port. If 0.0.0.0 is shown, your wireless router has not obtained an IP address
from your service provider.
If your router is unable to obtain an IP address from the your service provider, the problem might
be one of the following:
•
•
•
Your service provider might require a login. Ask your service provider whether they require
PPP over Ethernet (PPPoE) login.
The service name, user name, and password might be set incorrectly. See “Troubleshooting
Your service provider might check for your computer’s host name.
Assign the computer host name of your ISP account to the wireless router in the Basic Settings
screen.
•
Your service provider allows only one Ethernet MAC address to connect to Internet, and
might check for your computer’s MAC address, in this case, do one of the following:
•
Inform your service provider that you have bought a new network device, and ask them to
use the wireless router’s MAC address.
•
Configure your router to spoof your computer’s MAC address. This can be done in the
Basic Settings screen. Refer to the online help in the wireless router main menu.
Troubleshooting PPPoE
To troubleshoot a PPPoE connection:
1. Log in to the wireless router.
2. Under the Maintenance heading, select the Router Status link.
3. Click the Connection Status button.
4. If all of the steps indicate OK then your PPPoE connection is up and working.
Help with Troubleshooting
22
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
5. If any of the steps indicates Failed, you can attempt to reconnect by clicking Connect. The
wireless router will continue to attempt to connect indefinitely.
If you cannot connect after several minutes, you might be using an incorrect service name,
user name, or password. There also might be a provisioning problem with your ISP.
Unless you connect manually, the wireless router will not authenticate using PPPoE
until data is transmitted to the network.
Troubleshooting Internet Browsing
If your wireless router can obtain an IP address but your computer is unable to load any Web pages
from the Internet, check the following.
•
Your computer might not recognize any DNS server addresses.
A DNS server is a host on the Internet that translates Internet names (such as www addresses)
to numeric IP addresses. Typically your ISP provides the addresses of one or two DNS servers
for your use. If you entered a DNS address when you configured the wireless router, restart
your computer. Alternatively, you can configure your computer manually with DNS addresses,
as explained in the documentation for your computer.
•
Your computer might not have the wireless router configured as its default gateway.
Restart the computer, and verify that the wireless router address (192.168.1.1) is listed by your
computer as the default gateway address.
The factory default wireless router address is 192.168.1.1. However, if the router
detects a conflict with the address it gets from your modem, it automatically picks a
different address for itself. In this case, you can log in to the router using
www.routerlogin.net to verify its LAN IP address. Click the LAN IP Setup link in
the Advanced menu. Take note of the LAN TCP/IP setup IP address, which should
match the default gateway IP address on your computer.
Help with Troubleshooting
23
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
How Do I Restore the Default Password and Configuration
Settings?
This section explains how to restore the factory default configuration settings, changing the
router’s administration password to password and the IP address to 192.168.1.1.
This procedure will erase all the current configuration settings and restore the factory
defaults.
To restore the factory default configuration settings, use the reset button on the rear panel
of the router:
1. Use a sharp object like a pen or a paper clip to press and hold the default reset button for about
2. Release the reset button, and wait for the router to restart.
Troubleshooting Connectivity Using the Ping Utility
Most computers and routers have a diagnostic utility called ping that sends an request to a target
device. The device then replies. The ping utility makes it easy to troubleshoot a network..
This section includes advanced troubleshooting techniques.
Testing the Path from a PC to Your Router
You can ping the wireless router to verify that the LAN path from your computer to your router is
set up correctly.
1. From the Windows toolbar, click Start and select Run.
2. In the field provided, type Ping followed by the address of the router, as in this example:
or
ping 192.168.1.1
Help with Troubleshooting
24
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
3. Click OK.
You should see a message like this one:
Pinging 192.168.1.1 with 32 bytes of data
If the path is working, you see this message:
Reply from 192.168.1.1: bytes=32 time=NN ms TTL=xxx
If the path is not working, you see this message:
Request timed out
If the path is not functioning correctly, you could have one of the following problems:
•
•
Wrong physical connections
— Make sure that the LAN port light is on. If the light is off, follow the instructions in
— Check that the corresponding lights are on for your computer’s network interface
card.
Wrong network configuration
— Verify that the Ethernet card driver software and TCP/IP software are both installed
and configured on your computer.
— Verify that the IP address for your router and your computer are correct and that the
addresses on both begin with 192.168.1.0.
Help with Troubleshooting
25
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Testing the Path from a PC to the Internet
After verifying that the path between your computer and the wireless router works correctly, test
the path from your PC to the Internet. From the Windows Start > Run... menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISP’s DNS server.
If the path is functioning correctly, replies as in the previous section are displayed. If you do not
receive replies:
•
Check that your PC has the IP address of your router listed as the default gateway. If the IP
configuration of your PC is assigned by DHCP, this information is not visible in your PC’s
Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP default
gateway.
•
•
Check to see that the network address of your PC (the portion of the IP address specified by
the netmask) is different from the network address of the remote device.
If your ISP assigned a host name to your PC, enter that host name as the account name in the
Basic Settings screen.
Help with Troubleshooting
26
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
This section provides factory default settings and technical specifications for the Wireless Router
Model WPN824N.
Factory Default Settings
Smart Wizard
Enabled
Router Login Default Access
Router Login URL
Login Name (case-sensitive) printed on product label
admin
Login Password (case-sensitive) printed on product
label
password
Internet Connection
WAN MAC Address
MTU Size
Use default hardware address
1500
Local Network
Router Lan IP address printed on product label (also
known as Gateway IP address)
192.168.1.1
Router Subnet
255.255.255.0
Enabled
DHCP Server
Time Zone
Pacific Time
Disabled
Time Zone Adjusted for Daylight Saving Time
Firewall
Inbound (communications coming in from the Internet) Disabled (bars all unsolicited requests)
Outbound (communications going out to the Internet) Enabled (all)
Technical Specifications
27
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Wireless
Wireless Communication
Enabled
SSID Name
NETGEAR
Security
Disabled
Broadcast SSID
Transmission Speed
Country/Region
Operating Mode
Data Rate
Enabled
Autoa
United States in the US, otherwise varies by region
802.11 b/g and 802.11n
Best
Full
Output Power
a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary.
Network conditions and environmental factors, including volume of network traffic, building materials and
construction, and network overhead, lower actual data throughput rate.
Network Protocol and Standards Compatibility
Data and Routing Protocols:
TCP/IP, RIP-1, RIP-2, DHCP
PPP over Ethernet (PPPoE)
Power Adapter
North America:
United Kingdom, Australia:
Europe:
120V, 60 Hz, input
240V, 50 Hz, input
230V, 50 Hz, input
Japan:
100V, 50/60 Hz, input
12 V DC @ 1A output, 12W maximum
All regions (output):
Physical Specifications
Dimensions:
Weight:
223 x 153 x 31 mm (8.8 x 6 x 1.2 in.)
0.5 kg (1.2 lb)
Technical Specifications
28
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Environmental Specifications
Operating temperature:
Operating humidity:
0 to 40 C (32º to 104º F)
90% maximum relative humidity, noncondensing
Electromagnetic Emissions
Meets requirements of:
FCC Part 15 Class B
VCCI Class B
EN 55 022 (CISPR 22), Class B
C-Tick N10947
Interface Specifications
LAN:
10BASE-T or 100BASE-Tx, RJ-45
10BASE-T or 100BASE-Tx, RJ-45
WAN:
Wireless:
Maximum wireless signal rate complies with the IEEE 802.11
standard. Actual throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building
materials and construction, and network overhead, lower actual
data throughput rate.
Radio Data Rates:
1, 2, 5.5, 6, 9, 12, 18, 24, 36, 48, 54, MCS0, MCS1, MCS2, MCS3,
MCS4, MCS5, MCS6, and MCS7 Mbps
Auto Rate Sensing
2.4-2.5Ghz
Frequency
Data Encoding:
802.11b: Direct Sequence Spread Spectrum (DSSS)
802.11g: Orthogonal Frequency Division Multiplexing (OFDM)
Maximum Computers Per Wireless
Network:
Limited by the amount of wireless network traffic generated by each
node. Typically 30-70 nodes.
Operating Frequency Ranges:
2.412~2.462 GHz (US) 2.457~2.462 GHz (Spain)
2.412~2.484 GHz (Japan)2.457~2.472 GHz (France)
2.412~2.472 GHz (Europe ETSI)
802.11 Security:
40-bit (also called 64-bit) and 128-bit WEP, WPA-PSK and
WPA2-PSK.
Technical Specifications
29
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Documents
This appendix provides links to reference documents you can use to gain a more complete
understanding of the technologies used in your NETGEAR product.
Document
Link
TCP/IP Networking
Basics
Preparing Your Network
Glossary
Related Documents
30
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
RangeMax Wireless-N 150 Router Setup Manual
Related Documents
31
v1.0, November 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Registration and Certifications
Product Registration, Support, and Documentation
Register your product at http://www.NETGEAR.com/register. You must register before you can use our telephone
support service. Product updates and Web support are always available by going to: http://www.netgear.com/support.
Setup documentation is available on the CD, on the support website, and on the documentation website. When the
wireless router is connected to the Internet, click the KnowledgeBase link to view support information or click the
Documentation link to view the online User Manual for this wireless router.
Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic,
building materials and construction, and network overhead, lower actual data throughput rate.
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not
possible.
FCC Radiation Exposure Statement: This equipment complies with FCC/IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance or
20cm between the radiator and your body.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
|