Operating instructions
for vented tumble dryer
T 4123
To avoid the risk of accidents
or damage to the machine
it is essential to read these
Operating instructions before
it is installed or used for the first time.
G
M.-Nr. 06 067 720
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 25
Building under a continous worktop / in a kitchen run . . . . . . . . . . . . . . . . . . . 25
Aligning the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation - venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Calculating the effective duct length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Installation to the left or right side of the machine. . . . . . . . . . . . . . . . . . . . . . . . . 31
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
aVenting system with flexible ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
bVenting system with plastic piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
cConnecting directly to a wall vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Washer dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Increased drying level in the COTTONS programmes . . . . . . . . . . . . . . . . . . . . . 40
Increased drying level in the MINIMUM IRON programmes. . . . . . . . . . . . . . . . . 41
Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Before connecting the machine,
ensure that the connection data on
the data plate (fusing, voltage and
frequency) matches the mains
electricity supply. If in any doubt,
consult a qualified electrician.
To avoid the risk of accidents and
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, use and maintenance.
Keep these operating instructions in
a safe place and ensure that new
users are familiar with the content.
Pass them on to any future owner of
the machine.
The electrical safety of this
machine can only be guaranteed
when continuity is complete between
the machine and an effective earthing
system which complies with local and
national regulations. It is most important
that this basic safety requirement is
regularly tested, and where there is any
doubt the household wiring system
should be inspected by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
Correct use
The tumble dryer is only intended
for drying fabrics which have been
washed in a water solution, marked on
the manufacturer's wash care label as
being suitable for tumble drying.
"Dry Cleaning Kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk and follow
the instructions provided on the
packaging.
Do not connect the machine to the
mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
machine (e.g. danger or overheating).
Any other applications may be
dangerous. The manufacturer is not
liable for damage resulting from
improper use or operation.
The machine is built in accordance
with current safety requirements.
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
This machine is not a toy! To avoid
the risk of injury, do not allow
children to play on or near it, or to
play with the controls. Supervise its
use by the elderly or infirm.
Ensure current is not supplied to the
machine while maintenance or repair
work is being carried out.
Technical safety
Faulty components must only be
exchanged for Miele original spare
parts. Only when these parts are fitted
can the safety standards of the
machine be guaranteed.
Before setting up the machine
check it for any externally visible
damage. Do not install or use a
damaged machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
If the connection cable is faulty it
Adequate ventilation is essential,
especially where another
appliance which also uses the room air
(e.g. gas, oil or coal fired heater,
continuous flow or other water heater) is
installed in the same or an adjacent
room.
To ensure safe operation, and to
prevent gases given off by these
appliances being drawn back into the
room, an underpressure of 0.04 mbar is
the maximum permissible. Ventilation
can be maintained by air inlets which
cannot be blocked, in windows, doors
and outside wall vents, or by an auto-
matic window opening arrangement
when the tumble dryer is switched on. If
in doubt, the advice of a competent
builder, or for gas, a "Corgi" installer (in
UK) must be sought.
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In the event of a fault or for
cleaning purposes, the machine is
only completely isolated from the
electricity supply when:
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn.
Operation
This equipment is not designed for
maritime use or for use in mobile
installations such as caravans, aircraft
etc. However, it may be suitable for
such usage subject to a risk
assessment of the installation being
carried out by a suitably qualified
engineer.
The exhaust air must not be vented
into a chimney or vent flue which is
in use, nor should it be connnected to
ducting which ventilates rooms with
fireplaces. It would be dangerous if
smoke or exhaust fumes were drawn
back into the room.
This dryer must not be:
– connected to a chimney or vent flue
which is in use.
Do not install the machine in a
room where the temperature may
drop down to or below freezing. At very
cold temperatures the machine may be
difficult to start.
– used without exhaust ducting.
– used without the fluff filter in place or
if the fluff filter is damaged in any
way.
Always keep the area around the
machine free of dust and fluff.
Check all parts of the extraction
system on a regular basis (e.g. wall
vent, external grille, bends in the
ducting etc.) and make sure they are all
free of any hindrance. A build-up of fluff
will prevent a free-flow of air through the
system. If the dryer is to be connected
to an existing ducting system this must
be checked for suitability beforehand.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Always close the door after use.
This way you will avoid the danger
Using accessories
Accessory parts may only be fitted
when expressly approved by Miele.
If other parts are used, guarantee,
performance and product liability
claims may be invalidated.
of:
– children climbing onto or into the
dryer or hiding things in it.
– pets or other small animals climbing
into it.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Do not let anyone sit or lean on the
door, as this can cause the
machine to tip up.
There is danger of fire with fabrics
which:
– contain a large proportion of rubber,
foam rubber or rubber like materials.
– have been treated with inflammable
cleaning agents.
– have been splashed with hair
lacquer, hair spray, nail varnish
remover or similar substances.
– contain padding or fillings (e.g.
pillows, jackets). If these were
damaged the filling could leak out
with the risk of igniting in the dryer.
– are soiled with oil or grease.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not
be covered by the machine
guarantee.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Energy saving tips
^ Make sure that your laundry is
thoroughly spun before drying.
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled.
The higher the spin, the greater the
savings that can be made in energy
and time during drying.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
^ Load according to the optimum
amount of laundry recommended for
the programme being used (see
"Programme chart").
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Underloading is uneconomical.
Overloading gives a poorer quality of
drying and may cause unnecessary
creasing.
Disposal of your old machine
^ To avoid unecessarily long drying
times and high consumption of
energy:
Old machines contain materials which
can be reclaimed or recycled. Please
contact your dealer, your local waste
collection centre or scrap merchant
about potential recycling schemes.
– Make sure the room in which the
dryer is located is well ventilated.
– Make sure the fluff filter is clean
before using the dryer.
Ensure that the machine presents no
danger to children while being stored
for disposal.
– Check all parts of the ventilation
system on a regular basis and
remove any build up of fluff etc.
Before throwing an old machine away
unplug it and render the plug useless.
Cut off the cable directly behind the
machine to prevent misuse. This should
be done by a competent person.
^ The vent ducting should be as short,
straight and smooth as possible to
minimise any resistance to the air
throughflow.
This helps to reduce running times
and energy consumption levels.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
aProgramme selector
dI-On/0-Off button
The programme selector can be
turned clockwise or anti-clockwise.
To switch the machine on or off / to
interrupt a programme.
bProgramme sequence and check
eDoor Button
lamps
To open the door / to cancel a
programme.
cStart button
Pressing this button will open the
door even when the machine is
switched off at the mains.
Press the Start button to start a
programme.
The Start indicator lamp will flash as
soon as a programme can be
started. It lights up constantly once
the programme has started.
If the machine is switched on at the
mains and the door is opened the
drum lighting will come on. It will go
out a few minutes later to save
energy.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on laundry care
Wash care labels
Items filled with down.
The fabric lining on these garments
may shrink depending on the quality.
They can be partially dried using the
Smoothing programme.
Before drying check the drying
symbol on the wash care label.
Significance of symbols:
Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the wash care label,
as the surface of the fabric may
otherwise "roughen". These items can
be partially dried using the Smoothing
programme.
q Dry at normal temperature
r Dry at low temperature
sDo not tumble dry
If no symbol is featured, dry at your
own risk applying the following
principles:
Woven and loopknit materials (e.g.
T-shirts, knitted garments) have a
tendency to shrink, depending on their
quality and this is made worse by
over-drying. When purchasing these
garments it is advisable to take their
shrinkage properties into account.
Cotton and minimum iron items should
be dried using the appropriate
programme for the degree of drying
required. See programme chart.
For delicates and fabrics with the
following wash care label r dry using
the Low temperature option.
Minimum iron fabrics and 100% cotton
shirts or blouses tend to crease more,
the larger the load being dried,
particulary when the weave of the
fabric is very fine. Reduce the load or
use the MINIMUM IRON - Hand iron
programme with a max. load of 1 kg. If
this is unsatisfactory use the Special
care "Smoothing" setting, then hang the
garments on a hanger to dry.
Never overload the drum. Do not
exceed the maximum recommended
loads given in the "Programme
chart". Overloading can cause
unnecessary wear and tear to the
laundry, give a disappointing drying
result and cause more creasing.
Do not put soaking wet items into
the tumble dryer. Spin them
thoroughly after washing using the
appropriate spin speed.
Starched laundry can be dried in the
tumble dryer. In order to achieve the
usual finish, double the amount of
starch should be used.
New dark coloured garments should be
dried separately from light coloured
garments to avoid the danger of col-
ours running.
Tips on drying
Woollens and wool blends tend to
become matted and shrink if dried in a
tumble dryer. They can, however, be
partially dried using the Woollens hand
care programme.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programmes
COTTONS
Drying levels
Normal+
Fabric type
Special notes
maximum load:
5 kg (1)
Single and multi-layered
-
fabrics, e.g. mixed load of
cotton fabrics (e.g.
towelling, jerseywear).
Normal (2)
Load of similar cotton
fabrics (jersey wear,
flannelette sheets,
towelling).
If laundry is still too damp,
then:
- finish drying using Timed
drying Warm air.
- use the Normal+
programme next time.
Low temperature
Hand iron (2)
For drying delicate fabrics
with the symbol r (e.g.
acrylic garments).
Laundry is dried using the
Normal programme, but at a
lower temperature.
Cotton or linen fabrics (e.g.
table linen, bed linen,
-
starched laundry etc.).
Machine iron
Cotton or linen fabrics,
The laundry should be rolled
including starched laundry up to prevent it from drying
for machine ironing. out before it can be ironed.
(1) Weight of dry laundry
(2) Note for test institutes: Programme setting for testing according to EN 61121
standard
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programmes
MINIMUM IRON
Drying levels
Normal+
Fabric type
Special notes
maximum load:
2.5 kg (1)
Minimum iron items which
are made of synthetic or
blended fabrics (e.g.
pullovers, dresses, trousers)
which are not dried
Spin minimum iron fabrics
for at least 30 seconds in the
washing machine before
drying them.
adequately in the Normal
programme.
Normal (2)
Minimum iron shirts, table
Spin minimum iron fabrics
cloths etc. made of mixed for at least 30 seconds in the
fibres, e.g. cottons /
synthetics.
washing machine before
drying them.
Low temperature
For drying delicate fabrics
with the symbol r (e.g.
acrylic garments).
Laundry is dried using the
Normal programme, but at a
lower temperature.
Spin minimum iron fabrics
for at least 30 seconds in the
washing machine before
drying them.
Hand iron
Minimum iron shirts, table
Spin minimum iron fabrics
cloths etc. made of mixed for at least 30 seconds in the
fibres, e.g. cottons /
synthetics, which are still to
be hand ironed.
washing machine before
drying them.
For extra special care of
delicate fabrics and to
reduce creasing even more,
reduce the load to 1 kg. See
also "Special care
programmes".
(1) Weight of dry laundry
(2) Note for test institutes: Programme setting for testing according to EN 61121
standard
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Programme
Fabric type
Special notes
Special care programmes
Woollens
hand care
maximum load: 2 kg (1)
Woollen fabrics
To refresh and fluff up woollen
garments quickly. Remove garments
immediately at the end of the
programme. Do not repeat.
Woollen fabrics are not dried
completely by this programme.
Smoothing
maximum load: 2.5 kg (1)
Cottons and linen fabrics. Smooths out creasing caused during
Minimum iron items made
of cotton, blended fabrics
or synthetics, e.g. cotton
trousers, shirts.
the spin cycle in the washing
machine.
Fabrics are not completely dried in
this programme.
Remove garments immediately at
the end of the programme and place
on a line or hangers to dry.
TIMED DRYING
Warm air
maximum load: 5 kg (1)
Individual items
-
(e.g. bathing costumes,
bath towels, tea-towels).
Multi-layered fabric whose
layers have different drying
characteristics.
Cool air
Items which are to be aired
only.
-
(1)
Weight of dry laundry
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
A Prepare the laundry
Do not overload the drum.
^ As far as possible, sort laundry for:
- the type of fibre or weave,
- the degree of dryness required,
- similar size of items,
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
- the moisture content after
spinning.
This will help towards achieving an
even drying result.
See the "Programme chart" for
maximum recommended loads.
^ Before closing the door check that
the fluff filter is correctly positioned in
the door.
Fasten duvet covers etc. to prevent
small items from being rolled up inside
them.
Do up zips, hooks and eyes etc.
Tie fabric belts, apron strings.
Sew in or remove underwiring from
bras.
Make sure there is no detergent
dispenser ball etc. in with the
laundry, as this could melt and
damage the machine and the
laundry.
B Load the drum and switch
on the dryer
When closing the door make sure
items of laundry cannot be trapped
by the door, as this will cause
damage to the laundry.
^ Press the door button and open the
door.
^ Shut the door either with a gentle
swing or lean against it and push it
shut.
^ Load the laundry loosely into the
drum.
^ Switch the dryer on by pressing the
"l-On/0-Off" button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
C Select a programme
D Start the programme
^ Press the Start button.
The drying cycle begins.
The drying stage reached is shown by
the sequence indicator lamps on the
right hand side of the control panel.
At the end of the drying phase a
cooling down phase commences to
cool the laundry down. The Cool air
indicator lights up.
The required degree of dryness has
now been reached.
^ Turn the programme selector to the
required programme.
See "Consumption data" chart for
programme durations.
Low temperature
^ For drying particularly delicate
fabrics (care symbol r) e.g. acrylics
turn the programme selector to the
Low temperature position.
Because the temperature is reduced for
the Low temperature settings,
programme durations will be increased
and laundry will take longer to dry.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
Selecting a different programme
The programme has been successfully
cancelled when only the
Anti-crease/Finish indicator lamp is on.
As long as the cooling down phase or
the anti-crease phase has not been
reached it is possible to change a
programme after it has started by
turning the programme selector to a
different programme position.
E At the end of a programme
At the end of a programme the
Anti-crease/Finish lamp will come on in
the sequence display and the buzzer
will sound.
Interrupting a programme
^ Switch the machine off with the
I-On / 0-Off button.
The drum will continue to rotate at
intervals to prevent laundry creasing, if
you do not wish to remove it immediate-
ly. This anti-crease phase lasts for a
maximum of 60 minutes, except with
the Woollens hand care programme.
To continue drying:
^ Switch the dryer on with the
I-On / 0-Off button.
With COTTONS and MINIMUM IRON
programmes the programme will
continue unless the cooling down or
anti-crease phase has been reached.
^ Press the Door button and open the
door.
^ Remove the laundry.
With other programmes:
Make sure that the drum is empty. If
items are left in the dryer, they could
be damaged by overdrying when
the dryer is next used.
^ Press the Start button.
Adding or removing items
^ Clean the filter.
,Do not touch the back of the
drum when adding or removing
items. The drum could be very hot -
danger of burning.
^ Close the door.
^ Switch the dryer on by pressing the
l-On/0-Off.
^ Open the door. Take out or add items
as required.
^ To continue drying close the door
and press Start.
To cancel a programme
^ Turn the programme selector to
Finish or open the door .
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the fluff filter
A cleaning brush is available as an
optional extra from your Miele dealer
or the Miele Spare Parts Department.
The fluff which is created by the
drying process is collected in the fluff
filter in the door. Clean the filter after
every drying cycle.
You can also use a vacuum cleaner.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way. Close the door.
If there is a great deal of compacted
fluff on the filter, it can be cleaned
under hot running water.
^ After cleaning shake thoroughly until
no more water droplets are visible.
^ Dry the filter carefully.
^ Push the filter back into the door
holder until it clicks into position.
Make sure it is the right way round.
^ Open the door and pull the fluff filter
out of the door as illustrated.
^ Use your fingers to remove the fluff
from the surface of the filter.
^ Remove any fluff from the hollow part
of the door holder.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Tumble dryer
Disconnect the machine from the
power supply.
^ Clean the housing and control panel
with a mild cleaning agent or soapy
water.
Clean the drum and other stainless
steel parts with a suitable proprietary
stainless steel cleaner following the
manufacturer’s instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic surfaces and other
parts. The machine must never be
hosed down.
^ Dry all parts with a soft cloth.
E-Cloth
A microfibre "E-Cloth" is available from
the Miele UK Spare Parts Department,
which is suitable for cleaning surfaces
such as stainless steel, glass, plastic
and chrome without the use of
chemicals. It can be washed 300 times.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical equipment should only be carried out by a suitably
qualified person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
General problems
Problem
Possible cause
Remedy
The tumble dryer fails to No obvious cause.
start when switched on.
– Have you followed the
switch-on procedure
correctly (see “How to
dry correctly”)?
– Is the plug correctly
inserted in the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
machine or a fabric
drying.
conditioner sheet to the
load in the dryer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
There is a build up of
fluff.
Fluff is principally the
result of friction when
Fluff is collected by the
fluff filters and can be
garments are being worn easily removed (see
and washed. Machine
drying hardly causes any
fluff to form and, has
been established by
research institutes, to
have no effect on the
lifetime of fabric.
"Cleaning and Care").
The laundry is not
sufficiently dry.
The load consisted of
different fabrics.
– Finish drying using
"Timed drying - Warm
air".
– Select a more suitable
drying programme next
time (see "Programme
chart").
The interior drum
The lighting switches off Switch the dryer off and
lighting does not come automatically (to save
then on again.
on.
energy).
The lamp needs
changing.
Change the lamp as
described at the end of
this section.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The drying
Important: Before attempting to remedy one of the following
process goes on causes, switch the dryer off and switch on again to start the
too long or even
switches off.
programme again.
Ventilation to the dryer is
Open a door or window while
insufficient (e.g because it is the machine is in operation
installed in a room which is
too small).
for increased air flow.
The fluff filter may be
blocked.
Remove any fluff.
The laundry has not been
spun sufficiently.
Make sure that your laundry
is thoroughly spun at highest
spin speed for the type of
fabric.
The tumble dryer has been
overloaded.
Do not exceed the maximum
load for the programme
selected.
Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.
– Close zips and fasten any
hooks next time.
If the problem occurs again,
dry garments with long zips
using "Timed drying - Warm
air".
The vent ducting or the
ventilation outlet is blocked;
– Check all parts of the
extraction system on a
regular basis (e.g. wall
vent, external grille, bends
in the ducting etc.) and
make sure they are all free
of any hindrance.
– Remove any fluff.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The programme has
stopped. The
This is not a fault.
Use the "Timed drying -
Warm air" programme to
dry individual items.
The electronic unit has
recognised that there is no
laundry in the drum and
Anti-crease/Finish
lamp has come on in
the sequence display
and the buzzer is
sounding.
Before changing a
cancelled the programme. programme: Open and
close the drum door.
Drying individual garments
or items which are already
dry can also cause the
programme to be stopped.
The programme has
been interrupted. The
indicator lamp for
Hand iron or Machine
iron is flashing, and
the buzzer sounds.
No obvious cause.
– Switch the dryer off and
then on again.
– Then start the
programme again.
If the programme stops
again and the fault
message reappears there
is a fault. Contact the
Miele Service
Department.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
To change the interior drum
lamp
^ To close the flap push it upwards and
press it on the left and right until you
hear it click into position.
^ Open the door.
The cover must be fixed securely, as
otherwise moisture may seep in and
cause a short circuit.
Before changing the lamp,
disconnect the machine from the
mains power supply.
You will find the interior lamp cover at
the top of the drum aperture.
^ Insert the opener under the side
edge of the cover as illustrated.
^ Turn your wrist to make the cover
open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
The lamp must not exceed the
maximum wattage quoted on the
data plate and on the lamp cover.
^ Replace the lamp.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
After sales service
Repairs
PC indicator lamp (interface for
service technicians)
In the event of any faults which you
cannot remedy yourself, please contact The indicator lamp marked PC on the
fascia panel is the interface used by
the Miele service technicians during
– your Miele Dealer or
– The Miele Service Department (see
back cover for address).
service work for testing purposes.
Optional accessories
When contacting the Service
Department, please quote the model
and serial number of your machine,
both of which are shown on the data
plate situated on the right hand side
below the drum aperture.
Optional accessories for these dryers
are available from your Miele Dealer or
from the Miele Spare Parts Department.
Please note that telephone calls may
be monitored and recorded to
improve our service.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Front view
aVenting connection: rear, right or left
(supplied with the rear socket open)
bSupply cable for electrical
connection
cControl panel
dDoor
eFour height-adjustable screw feet
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
,Make sure the dryer door can be
opened without hindrance after
installation.
The building under kit is supplied with
its own installation instructions.
Transporting the machine to its
installation site
N.B. When built under drying times may
be longer.
When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer. To manoeuvre the
dryer out of its packing case to its
installation site you will also need to
hold it by the front feet.
Replacing the lid
If the lid has been removed in order to
fit a cover plate, ensure that, if the lid is
replaced, it fits securely into the rear
holders. Otherwise, it is not properly
secure for transport.
Building under a continous worktop /
in a kitchen run
The space required by the vent duct
must be taken into consideration when
calculating the distance between the
machine and a wall or other machines
or furniture on either side.
,A building under kit* is required
which must be fitted by a suitably
qualified person.
The machine lid is replaced by a
coverplate. It is essential that the
coverplate is fitted to ensure
electrical safety.
– When installing under a 900/910 mm
high worktop a spacer kit* is
required.
– Flat ducting* is required if there is not
enough space for a ventilation
ducting hoses or pipes.
– The electrical socket must be
located in an accessible position
near the machine.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Aligning the machine
,A ventilation gap of 10 mm must
be maintained between the base of
the machine and the floor. It must
not be blocked by deep pile
carpets, plinths, etc as this would
prevent a sufficient intake of air.
Washer-dryer stack
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.
The machine must be perfectly level to
ensure safe and proper operation.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
,Stacking kits must only be
installed by suitably qualified fitters.
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Electrical connection U.K.
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out
only by a suitably qualified and
If this machine is fitted with a
competent person, in strict accordance non-rewireable plug and the socket
with national and local safety
regulations.
outlets are not suitable for the plug
supplied or if the existing plug needs to
be replaced by a new one, the old plug
will need to be cut off and an
appropriate plug fitted. The fuse carrier
and the fuse should be removed from
the old plug and disposed of.
Ensure power is not supplied to the
machine while installation work is being
carried out.
The machine is supplied with a mains
cable with moulded plug for connection
to a 230-240V mains supply. The
voltage, rated load and fuse rating
are given on the data plate. Please
ensure these match the household
mains supply.
The plug cut from the cable should then
be disposed of and on no account be
inserted into any socket elsewhere in
the house (electric shock hazard).
The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Connection should be made via a fused
plug and suitable switched socket
which is easily accessible after
installation.
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100, section
739).
Do not connect via an extension lead.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Important
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
= live
Brown
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
If the colours of the wires in the mains
lead of this machine do not correspond
with the coloured markings identifying
the terminals of your plug, proceed as
follows:
^ The wire which is coloured green and
yellow must be connected to the
terminal in the plug which is marked
with the letter E or by the earth
symbol z or coloured green, or
green and yellow.
^ The wire which is coloured blue must
be connected to the terminal in the
plug which is marked with the letter N
or coloured black.
^ The wire which is coloured brown
must be connected to the terminal in
the plug which is marked with the
letter L or coloured red.
WARNING: THIS APPLIANCE
MUST BE EARTHED
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
General
Avoid:
– very long ducting systems
Important
– too many bends or corners; tight
corners;
Before operating the tumble dryer, a
suitable ducting system must be
installed to carry the moist air from
the dryer to the outside.
Otherwise the drying result will be less
effective and it will take longer and use
more energy.
This can be: . . .
. . . flexible ducting hose, or plastic
piping connected to the dryer, or
. . . or the dryer may be connected
directly to the wall vent.
Suitable materials
– for the ventilation ducting:
flexible ducting* or plastic piping
with a diameter of at least 100 mm.
– Before installing the ducting system,
ensure that the machine is not
– for venting to the outside:
a wall pipe kit* or a window vent kit*.
connected to the power supply.
* Available from your Miele dealer or the
Miele Spare Parts Department.
– The ducting outlet (e.g. wall pipe)
should be installed in such a way
that the moist expelled air . . .
. . . cannot be drawn back into
the room in which the dryer is
installed;
Procedure
^ First measure the duct length
required. Calculate the effective duct
length and establish the internal duct
diameter required (use the tables on
the next page).
. . . cannot cause any damage to
the building or other
nuisance.
– Adequate ventilation is essential as
the dryer uses the room air.
Ventilation can be maintained by:
- an open window;
^ Then decide which type of ducting
you want to use (see "Venting
systems" in this section).
- an air inlet which cannot be
blocked in windows, doors
and outside wall vents;
- a window switch which prevents
the dryer being used when the
window is closed.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Calculating the effective duct
length:
2. Internal duct diameter
^ Refer to Table II for the appropriate
duct diameter required.
Friction against the inner walls of the
ducting will slow down the expelled air
as it passes through. An elbow, bend,
non-return flap or wall vent creates
more friction than a straight duct. The
friction created by each of these is
expressed as an additional duct
length factor. The additional length
factors are calculated by comparing
the friction created by, for example, an
elbow to that created by 1 metre of
straight plastic piping (Table I).
Table I
Additional
duct length
factor
Flexible ducting*
– 1 m laid straight
– 45° angle
(Bend radius = 0.25 m)
– 90° angle
(Bend radius = 0.25 m)
1.8 m
1.5 m
2.5 m
Flexible aluminium ducting* / plastic
piping
– 1 m laid straight / or 1 m straight
1.0 m
0.6 m
0.8 m
The additional duct length factor for
each item needs to be added together
to ascertain the effective duct length
required.
pipe
– 45° angle / elbow
(Bend radius = 0.25 m)
– 90° angle / elbow
(Bend radius = 0.25 m)
A larger internal duct diameter also
helps reduce friction. If the effective
duct length is more than 20 m the
duct diameter should be increased
(Table II).
Wall vent kit* or window vent kit*
– with louvred grille
– with non-return flap (hinged flap)
Non-return flap* to be integrated into 14.3 m
the vent ducting
3.8 m
1.5 m
Flat ducting (for washer dryer
stack)*
11.0 m
1.0 m
1. To calculate the effective duct
length required:
Venting connection to the left/right
* optional accessory from Miele
^ First measure the distance which will
require straight ducting. Multiply this
amount by the corresponding
Table II
Maximum effective
Internal duct
additional duct length factor in Table I.
duct length allowable
diameter
required
^ Establish the number of angles,
bends etc. necessary and add their
additional duct length factors
10 m with Ring adapter
100 mm
20 m without Ring adapter 100 mm
40 m without Ring adapter 125 mm
100 m without Ring adapter 150 mm
together with the help of Table I.
^ Add all the additional duct length
factors together to get the effective
duct length.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
3. Example
Installation to the left or right
side of the machine
At the rear
The connection is opened at the
factory.
^ Fit one of the venting systems
described on the following pages.
Left or right side of the machine
A
Wall pipe, with louvred vent
= 1 x 3.8 m Additional duct
length
= 3.8 m
= 1.6 m
= 0.5 m
B/D 2 Elbows, 90°
= 2 x 0.8 m Additional duct
length
C
E
0.5 m plastic piping
= 0.5 x 1 m Additional duct
length
^ Remove the left or right hand side
cover cap. Do not remove the frame.
Refit it in the rear outlet.
Side connection, left
= 1 m Additional duct length
Effective duct length
= 1.0 m
= 6.9 m
Result: A duct diameter of 100 mm is
adequate as the effective duct length is
less than the 20 m specified in Table II.
^ Ensure it is securely in position so
that it cannot fall out when the dryer
is in operation.
^ Fit one of the venting systems
described on the following pages.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Venting systems overview
aVenting system with flexible
ducting
The various venting systems which are
possible (a b c) are described on
the following pages.
This is a simple, cost effective
method of directing the moist air
outside. The adapter is fitted into the
vent opening on the dryer and the
ducting hose is then connected to
the adapter.
Adapter
^ The following items are required:
... flexible ducting hose
... a wall vent kit* or window vent kit*.
* (Miele optional accessory).
A ring adapter** (1) is installed in
adapter (2) for the installation of a
flexible vent duct. It reduces time and
energy requirements during drying
when used in combination with a short
vent duct (maximum 10 m total
length). The ring adapter is removable
and designed for use with all venting
systems.
^ Ring adapter (1) must be taken out of
adapter (2), if the total duct length is
longer than 10 m.
If the total duct length is less than 10
m the ring adapter should be left in
the adapter.
** Note for test institutes: EN 61121 Standard
testing is carried out with the ring adapter.
^ Fit adapter (2) into the vent opening
on the dryer, and connect vent hose
(3).
^ See next page for examples.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Installation examples - venting
system with flexible ducting
Connection to an exhaust flue
Window vent
1. Pipe with connection piece
(= supplied with the Miele wall vent
kit)
1. Window vent kit (fitted in a
"plexiglass" pane)
2. Adapter for flexible hose
(separate fitting instructions are
supplied with the Miele window vent
kit)
3. Exhaust flue insulated against damp
,The ducting must not be vented
into a chimney or vent flue which is
in use, nor should it be connected to
ducting which ventilates rooms with
fireplaces.
2. Adapter for flexible hose
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
bVenting system with
If the total duct length is greater than
10 m the ring adapter is not required.
plastic piping
BFit Miele adapter (2) into the vent
Plastic piping is a good option where
the vented air has to ducted for some
distance. The smooth walls of the
pipe are less resistant to the vented
air than the walls of a flexible vent
hose, for example. Time and energy
consumption are better with plastic
piping.
opening on the dryer.
CAttach the pipe (3).
Example
^ The following items are required: . .
. . . an adapter* (dia. 100 mm)* with
rib on the inside.
. . . a wall vent kit* or window vent
kit*.
* (Miele optional accessory)
. . . Suitable plastic piping is
available from your dealer or
builder’s merchant. If a pipe diameter
greater than 100 mm is required,
additional adapters are necessary
(e.g. to increase from C 100 to 125
mm) to connect the pipe to the dryer.
1. Wall vent kit
(Separate fitting instructions are
supplied with the Miele wall vent kit).
2. Adapter
3. Plastic piping, diameter DN 100
AThe ring adapter (1) only needs to be
fitted into the Miele adapter (2), if the
total duct length is less than 10 m.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
cConnecting directly to a wall Side view:
vent
The best method of venting the dryer
is to connect it directly to the outside
wall of a room. However, it is
necessary to insert the wall vent right
through the wall.
Because the vented air is blown
directly outside, and has only a short
distance to go, this system is very
efficient in terms of time and energy
consumption.
^ A wall pipe and a flexible foam
gasket must be used (both Miele
optional accessories).
1. Wall pipe
2. Flexible foam gasket
ABefore drilling into the wall . . .
. . . please read the installation
instructions supplied with the Miele
wall pipe.
. . . and study the following
diagrams.
View from above:
BInsert the ring adapter (1) into the
wall pipe.
CFit the foam gasket (3) on to the
connecting piece (2) on the wall pipe
and push the dryer up against the
wall.
1. Wall pipe
2. Flexible foam gasket
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Washer dryer stack
Miele washing machine with Comfort
line angled fascia
Height of venting outlet for washer
dryer stack
Miele washing machine with straight or
sloping fascia
Stacking kit* without worktop:
C = 94.2 cm
D = 170.0 cm
Stacking kit* without worktop:
A = 94.2 cm
Stacking kit* with worktop:
C = 96.0 cm
B = 170.0 cm
D = 171.8 cm
Stacking kit* with worktop:
A = 92.8 cm
* Miele optional accessories
B = 168.6 cm
* Miele optional accessories
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption data
Programmes
Capacity
Final spin speed
(in a domestic
Electricity
consumption
Drying time
(incl.
washing machine)
cooling down
time)
kg
rpm
kWh
Minutes
COTTONS
Normal+
5.0
1200
1400
1600
1800
2.70
2.60
2.30
2.25
3.30
2.60
2.45
2.20
2.15
2.60
1.90
1.80
1.50
1.45
1.50
1.40
1.15
1.10
70
67
60
59
84
67
64
57
56
69
52
49
42
41
42
39
33
31
Normal (1)
Normal
5.0
5.0
800 (70 % residual moisture)
1200
1400
1600
1800
Hand iron (1)
Hand iron
5.0
5.0
800 (70 % residual moisture)
1200
1400
1600
1800
1200
1400
1600
1800
Machine iron
5.0
MINIMUM IRON
Normal (1)
2.5
2.5
1000 (50 % residual moisture)
1000
1.15
1.00
33
30
Hand iron
Special programmes
Woollens hand
care
2.0
2.5
-
-
0.20
0.30
3
8
Smoothing
(1) EN 61121 test programme
EN 61121 Standard testing is carried out with the ring adapter.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry
with 70% residual moisture as per the above standard using the Normal Cottons
programme without selecting any additional functions.
Consumption data can vary from the nominal values given above depending
on the size of the load, types of textiles, residual moisture levels after spinning,
fluctuations in the electricity supply and any additional options selected.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
85 cm (adjustable +0.7/-0.7 cm)
82 cm
Height without lid
Depth with door open
Width
106 cm
59.5 cm
Depth
58 cm
Weight
48 kg
Drum volume
Maximum capacity
Length of connection cable
Voltage
100 litres
5 kg dry weight
1.60 m
see data plate
see data plate
see data plate
see data plate
see "Consumption data"
Radio/TV suppressed, VDE
Rated load
Fuse rating
Lamp wattage
Energy consumption
Test certificates awarded
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
for changing
standard settings
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Increased drying level in the
COTTONS programmes
ETurn the programme selector to the
COTTONS Normal position.
– If the Drying indicator lamp is not on,
the increased drying level is
deactivated.
The machine is designed to dry
using as little energy as possible.
However, if you require the laundry to
be drier, it is possible to reduce the
final moisture level in the COTTONS
programmes. Note that programme
durations will be longer if this option
is activated.
– If the Drying indicator lamp is
flashing, the increased drying level is
activated.
FPressing the Start button switches
between activating and deactivating
increased drying.
The machine is supplied ex-works with
this option switched off. It can be
activated is wished.
GSwitch the machine off with the
I-On / 0-Off button.
Follow steps A to G to programme and The setting you have selected is now
store in memory.
stored in memory. You can change it
again at any time.
The programmable functions are
activated with the help of the Start
button and the programme selector.
To check:
^ Carry out steps A to E.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
If the indicator lamp for Drying
flashes = Increased drying level
is switched on
is not on = Increased drying level
– The programme selector is at Finish.
is switched off
APress the Start button and keep it
pressed in whilst carrying out steps
B to C.
^ Switch off the dryer.
The check is complete.
BSwitch the dryer on with the
I-On / 0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Increased drying level in the
MINIMUM IRON programmes
ETurn the programme selector to the
COTTONS Low Temperature
position.
The machine is designed to dry
using as little energy as possible.
However, if you require the laundry to
be drier, it is possible to reduce the
final moisture level in the MINIMUM
IRON programmes. Note that
– If the Drying indicator lamp is not on,
the increased drying level is
deactivated.
– If the Drying indicator lamp is
flashing, the increased drying level is
activated.
programme durations will be longer if
this option is activated.
FPressing the Start button switches
between activating and deactivating
increased drying.
The machine is supplied ex-works with
this option switched off. It can be
activated if wished.
GSwitch the machine off with the
I-On / 0-Off button.
Follow steps A to G to programme and
store in memory.
The setting you have selected is now
stored in memory. You can change it
again at any time.
The programmable functions are
activated with the help of the Start
button and the programme selector.
To check:
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
^ Carry out steps A to E.
If the indicator lamp for Drying
flashes = Increased drying level
is switched on
– The programme selector is at Finish.
is not on = Increased drying level
APress the Start button and keep it
pressed in whilst carrying out steps
B to C.
is switched off
^ Switch off the dryer.
The check is complete.
BSwitch the dryer on with the
I-On / 0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Buzzer
ETurn the programme selector to the
COTTONS Hand iron position.
An audible tone sounds repeatedly at
the end of a programme.
– If the Drying lamp is flashing, the
buzzer is activated.
The buzzer is activated as standard
ex-works. It can be deactivated if
wished.
– If the Drying lamp is not on, the
buzzer is deactivated.
FPressing the Start button switches
between activating and deactivating
the buzzer.
The buzzer will sound if there is a fault,
even if it has been deactivated.
Follow steps A to G to programme and
store in memory.
GSwitch the machine off with the
I-On / 0-Off button.
The programmable functions are
activated with the help of the Start
button and the programme selector.
The setting you have selected is now
stored in memory. You can change it
again at any time.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
To check:
^ Carry out steps A to E.
If the indicator lamp for Drying
flashes = The Buzzer
is activated
– The programme selector is at Finish.
APress the Start button and keep it
pressed in whilst carrying out steps
B to C.
is not on = The Buzzer
is deactivated
^ Switch off the dryer.
BSwitch the dryer on with the
I-On / 0-Off button.
The check is complete.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved/0504
M.-Nr. 06 067 720 / 00
This paper consists of cellulose which has been bleached without the use of chlorine.
Download from Www.Somanuals.com. All Manuals Search And Download.
|