Operator’s Manual
Two-Stage Snow Thrower
Styles C & D
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if
any). If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark
arrester for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131
Cleveland, Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
FORM NO. 769-01274B.
(7/27/2004)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer, birth defects or
other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
4. Use a grounded three-wire extension cord and
receptacle for all units with electric start engines.
5. Adjust collector housing height to clear gravel or
crushed rock surfaces.
Training
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe
place for future and regular reference and for
ordering replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 14 years old to operate
this machine. Children 14 years old and over
should read and understand the operation
instructions and safety rules in this manual and
should be trained and supervised by a parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Thrown objects can cause serious personal injury.
Plan your snow-throwing pattern to avoid discharge
of material toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at
least 75 feet from the machine while it is in
operation. Stop machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling,
especially when operating in reverse.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while
engine is running, except where specifically
recommended in the operator’s manual.
8. Let engine and machine adjust to outdoor
temperature before starting to clear snow.
9. To avoid personal injury or property damage use
extreme care in handling gasoline. Gasoline is
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes, which can ignite.
Wash your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes
before refueling.
f. Never over fill fuel tank. Fill tank to no more
than ½ inch below bottom of filler neck to
provide space for fuel expansion.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine
and equipment. Move machine to another
area. Wait 5 minutes before starting the
engine.
i. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light (e.g. furnace, water heater, space
heater, clothes dryer etc.).
Preparation
1. Thoroughly inspect the area where the equipment
is to be used. Remove all doormats, newspapers,
sleds, boards, wires and other foreign objects,
which could be tripped over or thrown by the auger/
impeller.
2. Always wear safety glasses or eye shields during
operation and while performing an adjustment or
repair to protect your eyes. Thrown objects which
ricochet can cause serious injury to the eyes.
3. Do not operate without wearing adequate winter
outer garments. Do not wear jewelry, long scarves
or other loose clothing, which could become
entangled in moving parts. Wear footwear which
will improve footing on slippery surfaces.
j. Allow machine to cool at least 5 minutes
before storing.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
18. Never put your hand in the discharge or collector
openings. Always use the clean-out tool provided to
unclog the discharge opening. Do not unclog chute
assembly while engine is running. Shut off engine
and remain behind handles until all moving parts
have stopped before unclogging.
19. Use only attachments and accessories approved
by the manufacturer (e.g. wheel weights, tire
chains, cabs etc.).
20. If situations occur which are not covered in this
manual, use care and good judgment. Contact your
dealer or call 1-800-800-7310 for assistance and
the name of your nearest servicing dealer.
Operation
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact
with the rotating parts can amputate hands and
feet.
2. The auger/impeller control lever is a safety device.
Never bypass its operation. Doing so makes the
machine unsafe and may cause personal injury.
3. The control levers must operate easily in both
directions and automatically return to the
disengaged position when released.
4. Never operate with a missing or damaged chute
assembly. Keep all safety devices in place and
working.
Maintenance & Storage
5. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
6. Do not operate machine while under the influence
of alcohol or drugs.
7. Muffler and engine become hot and can cause a
burn. Do not touch.
8. Exercise extreme caution when operating on or
crossing gravel surfaces. Stay alert for hidden
hazards or traffic.
9. Exercise caution when changing direction and
while operating on slopes.
10. Plan your snow-throwing pattern to avoid discharge
towards windows, walls, cars etc. Thus, avoiding
possible property damage or personal injury
caused by a ricochet.
11. Never direct discharge at children, bystanders and
pets or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to
clear snow at too fast of a rate.
13. Never operate this machine without good visibility
or light. Always be sure of your footing and keep a
firm hold on the handles. Walk, never run.
14. Disengage power to the auger/impeller when
transporting or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use
care when backing up.
16. If the machine should start to vibrate abnormally,
stop the engine, disconnect the spark plug wire and
ground it against the engine. Inspect thoroughly for
damage. Repair any damage before starting and
operating.
17. Disengage all control levers and stop engine before
you leave the operating position (behind the
handles). Wait until the auger/impeller comes to a
complete stop before unclogging the chute
assembly, making any adjustments, or inspections.
1. Never tamper with safety devices. Check their
proper operation regularly. Refer to the
maintenance and adjustment sections of this
manual.
2. Before cleaning, repairing, or inspecting machine
disengage all control levers and stop the engine.
Wait until the auger/impeller come to a complete
stop. Disconnect the spark plug wire and ground
against the engine to prevent unintended starting.
3. Check bolts and screws for proper tightness at
frequent intervals to keep the machine in safe
working condition. Also, visually inspect machine
for any damage.
4. Do not change the engine governor setting or over-
speed the engine. The governor controls the
maximum safe operating speed of the engine.
5. Snow thrower shave plates and skid shoes are
subject to wear and damage. For your safety
protection, frequently check all components and
replace with original equipment manufacturer’s
(OEM) parts only. “Use of parts which do not meet
the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage
and disengage properly and adjust, if necessary.
Refer to the adjustment section in this operator’s
manual for instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear
snow from machine and prevent freeze up of auger/
impeller.
10. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as a water heater, furnace, clothes dryer etc.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
YOUR RESPONSIBILITY
Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in
this manual and on the machine.
Do not modify engine
Notice regarding Emissions
To avoid serious injury or death, do not modify engine
in any way. Tampering with the governor setting can
lead to a runaway engine and cause it to operate at
unsafe speeds. Never tamper with factory setting of
engine governor.
Engines which are certified to comply with California
and federal EPA emission regulations for SORE (Small
Off Road Equipment) are certified to operate on regular
unleaded gasoline, and may include the following
emission control systems: Engine Modification (EM)
and Three Way Catalyst (TWC) if so equipped.
SAFETY LABELS FOUND ON YOUR SNOW THROWER
DANGER
DANGER
DANGER
1.KEEP AWAY FROM ROTATING IMPELLER
AND AUGER. CONTACT WITH IMPELLER OR
AUGER CAN AMPUTATE HANDS AND FEET
.
USE CLEAN-OUT TOOL TO UNCLOG
2.
3.
DISCHARGE CHUTE.
DISENGAGE CLUTCH LEVERS, STOP ENGINE,
AND REMAIN BEHIND HANDLES UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING OR SERVICING MACHINE.
TO AVOID THROWN OBJECTS INJURIES,
NEVER DIRECT DISCHARGE AT BYSTANDERS.
USE EXTRA CAUTION WHEN OPERATING ON
GRAVEL SURFACES.
4.
5.
NEVER PUT HAND IN CHUTE. CONTACT WITH
ROTATING PARTS CAN AMPUTATE FINGERS
AND HANDS.
SHUT OFF ENGINE AND WAIT UNTIL ALL
MOVING PARTS HAVE STOPPED BEFORE
UNCLOGGING.
AVOID INJURY FROM
ROTATING AUGER -
KEEP HANDS, FEET
AND CLOTHING AWAY.
READ OPERATOR'S MANUAL.
CLEAN-OUT TOOL
USE CLEAN-OUT TOOL OR WOODEN STICK TO
UNCLOG DISCHARGE CHUTE.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: ASSEMBLING YOUR SNOW THROWER
1
2
3
NOTE: References to right or left side of the snow
thrower are determined from behind the unit in the
operating position (standing directly behind the snow
thrower, facing the handle panel).
NOTE: This Operator’s Manual covers several
models. Snow thrower features vary by model. Not
all features referenced and pictured in this manual are
applicable to all snow thrower models.
IMPORTANT: Two replacement auger shear pins and
cotter pins are included with this manual. Refer to
pin replacement.
CAUTION: Prior to operating your snow
Read and follow all instructions carefully and
perform all adjustments to verify your snow
thrower is operating safely and properly.
Securing the Handle
1. Observe the lower rear area of the snow thrower to
be sure both cables are aligned with roller guides
before pivoting the handle upward until it clicks into
the place.
2. Secure the right side of the handle by tightening the
plastic wing knob.
3. Secure the left side of the handle by tightening the
plastic wing knob into the eyebolt.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
Attaching the Chute Assembly and Directional Control
1. Apply a light lubricant (i.e. 3-in-1 oil) to the rim of
the chute base and position the chute assembly
over the base.
2. Close the flange keepers to secure the chute
assembly to the chute base. The flange keepers
will click into place when properly secure.
3. Remove the flat washer and hairpin clip from the
end of the chute directional control. Insert the end
of the chute directional control into the lower
bracket and secure with the flat washer and hairpin
clip just removed.
NOTE: If necessary, the lower bracket can be
3
CAUTION: Prior to operating your snow
Read and follow all instructions carefully and
perform all adjustments to verify your snow
thrower is operating safely and properly.
Tire Pressure
•
Before operating, check tire pressure and reduce
pressure in both tires to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires,
the unit may not travel in a straight path and the shave
plate may wear unevenly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: KNOW YOUR SNOW THROWER
Drive Control
Auger Control
Electric Starter Button
Engine Controls
Gas Cap
Oil Fill
Recoil Starter
Handle
Electric Starter Outlet
Shift Lever
Chute Assembly
Primer
Clean-out
Tool
Ignition
Key
Chute Directional
Control
Choke
Control
Throttle
Control
Skid Shoe
Augers
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
Choke Control
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the
Tecumseh Engines manual packed separately and
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating
the choke control closes the choke plate on the
carburetor and aids in starting the engine.
Shift Lever
Throttle Control
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine
when pushed down completely.
The shift lever is located between the lower handle,
behind the engine. Place the shift lever into any of
seven positions to control the direction of travel and
ground speed.
Primer
Forward
Depressing the primer forces fuel
directly into the engine’s carburetor to
aid in cold-weather starting.
There are five forward (F) speeds. Position one (1) is
the slowest and position five (5) is the fastest.
Reverse
There are two reverse (R) speeds. One (1) is the slower
and two (2) is the faster.
Oil Fill
Engine oil level can be checked and
oil added through the oil fill.
Gas Cap
Unthread the gas cap to add gasoline to the fuel tank.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Control
Ignition Key
The ignition key is a safety devise. It must be fully
inserted in order for the engine will start. Remove the
ignition key when the snow thrower is not in use.
AUGER
CONTROL
IMPORTANT: Do not turn the ignition key in an attempt
to start the engine. Doing so may cause it to break.
Clean-Out Tool
WARNING: Never use your hands to clear
a clogged chute assembly. Shut off engine
and remain behind handles until all moving
parts have stopped before unclogging.
GO
The auger control is located on the left handle.
Squeeze the control grip against the handle to engage
the augers and start snow throwing action. Release to
stop.
The chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is
designed to clear a clogged chute assembly. Refer to
Operating Your Snow Thrower section for more detailed
information regarding the chute clean-out tool.
Drive Control
NOTE: This item is fastened with a cable tie to the
rear of the auger housing at the factory. Cut the cable
tie before operating the snow thrower.
DRIVE
CONTROL
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
GO
Recoil Starter Handle
The recoil starter handle is used to manually start the
engine.
The drive control is located on the right handle.
Squeeze the control grip against the handle to engage
the wheel drive. Release to stop.
Electric Starter Button (If so equipped)
Pressing the electric starter button engages the
engine’s electric starter when plugged into a 120V
power source.
Chute Directional Control
CHUTE DIRECTIONAL CONTROL
Electric Starter Outlet (If so equipped)
ADJUSTABLE
Requires use of a three-prong outdoor extension cord
(packed with the snow thrower) and a 120V power
source/wall outlet.
CHUTE TILT
DISCHARGE
RIGHT
DISCHARGE
LEFT
Augers
When engaged, the augers rotate and draw snow into
the housing.
Chute Assembly
The chute directional control is located on left side of
the snow thrower.
Snow drawn into the auger housing is discharged out
the chute assembly.
To change the direction in which snow is thrown, turn
chute directional control as follows:
•
•
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATING YOUR SNOW THROWER
WARNING: If your home electrical
system is grounded, but a three-hole
receptacle is not available, do not use your
snow thrower’s electric starter.
Before Starting
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
If you have a grounded three-prong receptacle,
proceed as follows:
Gas & Oil Fill-Up
•
Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of
extension cord into a three-prong 120-volt,
grounded, AC outlet in a well-ventilated area.
Rotate choke control to FULL choke position (cold
engine start).
Service the engine with gasoline and oil as instructed in
the Tecumseh Engines manual packed separately with
your snow thrower. Read instructions carefully.
•
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel the machine indoors or while the
engine is hot or running. Extinguish cigarettes,
cigars, pipes and other sources of ignition.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
•
Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
•
A small plastic cup may be located inside the fuel fill
opening beneath the gas cap. Remove and discard
this cup before filling up the tank.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
Starting The Engine
•
•
Push starter button to start engine.
Once the engine starts, immediately release starter
button.
•
Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the boot) is fastened securely over the metal
tip on the spark plug.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to FULL and
then slowly into the OFF position again.
When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
•
•
Make certain both the auger control and drive
control are in the disengaged (released) position.
Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
•
NOTE: The engine cannot start unless the key is
Recoil Starter
inserted into ignition switch.
•
Rotate choke control to FULL choke position (cold
engine start).
Electric Starter (on models so quipped)
•
Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
•
Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
CAUTION: If your home’s wiring system
is not a three-wire grounded system, do
not use this electric starter under any
conditions.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
WARNING: The optional electric starter is
equipped with a grounded three-wire power
cord and plug, and is designed to operate on
120 volt AC household current. It must be
used with a properly grounded three-prong
receptacle at all times to avoid the possibility
of electric shock. Follow all instructions
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
•
Grasp the recoil starter handle and slowly pull the
rope out. At the point where it becomes slightly
harder to pull the rope, slowly allow the rope to
recoil.
carefully prior to operating the electric starter.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Pull the starter handle with a firm, rapid stroke.
To Engage Drive
IMPORTANT: Do not release the handle and allow it to
snap back. Keep a firm hold on the starter handle and
allow it to slowly recoil.
•
Move shift lever into one of the six forward (F)
positions or two reverse (R) positions. Select a
speed appropriate for the snow conditions and a
pace you’re comfortable with.
•
As the engine warms, slowly rotate the choke
control to the OFF position. If the engine falters,
quickly rotate the choke control back to the FULL
position and then slowly into the OFF position
again.
IMPORTANT: Use the slower speeds until you are
comfortable and familiar with the operation of the snow
thrower.
•
Squeeze the drive control against the handle the
snow thrower will move. Release it and drive
motion will stop.
Stopping The Engine
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible starter freeze-up, proceed
as follows:
IMPORTANT: NEVER reposition the shift lever (change
speeds or direction of travel) without first releasing the
drive control and bringing the snow thrower to a
complete stop. Doing so will result in premature wear to
the snow thrower’s drive system.
•
Electric Starter (on models so equipped)
1. Connect extension cord to the electric starter outlet
on the engine, then to 120 volt AC outlet.
2. With the engine running, push the starter button
and allow the starter for spin for several seconds.
The noise made by the starter is normal. The
engine’s starter is not being harmed.
3. When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow
thrower.
To Engage Augers
•
To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
Auger Control Test
IMPORTANT: Perform the following test before
operating your snow thrower for the first time and at the
start of each winter season.
4. Move throttle control to STOP position.
5. Remove the ignition key.
Check the adjustment of the auger control as follows:
6. Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
•
When the auger control is released and in the
disengaged “up” position, the cable should have
very little slack. It should NOT be tight.
In a well-ventilated area, start the snow thrower
engine as instructed earlier in this section under the
heading Starting the Engine. Make sure the throttle is
set in the FAST position.
•
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
•
•
While standing in the operator’s position (behind
the snow thrower), engage the auger.
Allow the auger to remain engaged for
approximately ten (10) seconds before releasing
the auger control. Repeat this several times.
With the throttle control in the FAST (rabbit)
position and the auger control in the disengaged
“up” position, walk to the front of the machine.
Confirm that the auger has completely stopped
rotating and shows NO signs of motion.
Recoil Starter
1. With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud
clattering sound, which is not harmful to engine.
2. Move throttle control to STOP position.
3. Remove the ignition key.
•
•
NOTE: Keep the key in a safe place. The engine
cannot start without the ignition key.
IMPORTANT: If the auger shows ANY signs of rotating,
immediately return to the operator’s position and shut
off the engine. Wait for ALL moving parts to stop before
re-adjusting the auger control.
4. Wipe all snow and moisture from the carburetor
cover in the area of the drive control and auger
control. Also, engage and release the controls
several times.
•
•
•
To readjust the control cable, loosen the hex jam
nut on the auger control cable “Z” fitting.
Rotate the coupling end of the cable
counterclockwise to provide more slack.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Repeat Auger Control Test to verify proper
adjustment has been achieved.
Drift Cutters (on models so equipped)
Drift cutters should be used when operating the snow
thrower in heavy drift conditions.
On models so equipped, drift cutters are assembled to
the auger housing inverted. Remove the carriage bolts
by unthreading the hex nuts which secure them, and
reinstall the drift cutters in their proper position before
operating the snow thrower. See Figure 2.
Drift
Cutter
Figure 1
Carriage Screws /
Hex Nuts
Drive / Auger Lock (on models so equipped)
The drive/auger lock allows the user to operate the
snow thrower with one hand, leaving the left hand free
to operate the chute directional control.
Figure 2
If your unit is not equipped with drift cutters, contact
information regarding price and availability.
•
Engage both the Auger Control and the Drive
Control at the same time.
•
Release the Auger Control and it will remain
engaged until the Drive Control is also released.
Tire Chains (on models so equipped)
Tire chains should be used whenever extra traction is
needed. If your unit is not equipped with tire chains,
information regarding price and availability.
Chute Clean-Out Tool
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly
during operation, proceed as follows to safely clean the
chute assembly and chute opening:
Operating Tips
•
Release both the Auger Control and the Drive
Control
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power
until it reaches operating temperature.
.
•
•
Stop the engine by removing the ignition key.
Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
WARNING: The muffler, engine and
surrounding areas become hot and can
cause a burn. Do not touch.
•
•
Always operate the snow thrower with the throttle
control in the FAST (rabbit) position.
WARNING: Never use your hands to clean
snow and ice from the chute assembly or
auger housing
•
•
•
Discharge snow downwind whenever possible.
Slightly overlap each previous swath.
Set the skid shoes 1/4” below the scraper bar for
normal usage. The skid shoes may be adjusted
upward for hard-packed snow. Adjust downward
when using on gravel or crushed rock.
•
•
Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition
key and start the snow thrower’s engine.
While standing in the operator’s position (behind
the snow thrower), engage the auger control for a
few seconds to clear any remaining snow and ice
from the chute assembly.
•
Avoid possible starter freeze-up. Clean the snow
thrower thoroughly after each use.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: MAKING ADJUSTMENTS
Drive Control
When the drive control is released and in the
disengaged “up” position, the cable should have very
little slack. It should NOT be tight.
Check the adjustment of the drive control as follows:
1. With the drive control released, push the snow
thrower gently forward. The unit should roll freely.
2. Engage the drive control and gently attempt to push
the snow thrower forward. The wheels should not
turn. The unit should not roll freely.
3. With the drive control released, move the shift lever
back and forth between the R2 position and the F6
position several times. There should be no
resistance in the shift lever.
If any of the above tests failed, the drive cable is in need
of adjustment. refer to the figure at the right and
proceed as follows:
Figure 3
Figure 4
Figure 5
•
Loosen the hex jam nut on the auger control cable
“Z” fitting and rotate the coupling end of the cable
downward to provide more slack or upward to take
up slack. See Figure 3.
•
Retighten the hex jam nut and repeat all three tests
to verify proper adjustment has been achieved.
Skid Shoes
The space between the skid shoes and the ground can
be adjusted. See Figure 4.
•
For close snow removal on a smooth surface, raise
skid shoes higher on the auger housing.
•
Use a middle or lower position when the area to be
cleared is uneven, such as a gravel driveway.
CAUTION: Loose gravel can be picked up
and thrown by the auger, causing injury to the
operator and bystanders and/or damage to
the snow thrower and surrounding property.
•
•
Adjust skid shoes by loosening the four hex nuts
(two on each side) and carriage bolts. Move skid
shoes to desired position.
Make certain the entire bottom surface of skid shoe
is against the ground to avoid uneven wear on the
skid shoes. Retighten nuts and bolts securely.
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so, loosen the two nuts
which secure the chute bracket and reposition it slightly
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Tire Pressure
•
Before operating, check tire pressure and reduce
pressure to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other.
Auger Control
control.
Chute Assembly
The distance snow is thrown can be adjusted by
changing the angle of the chute assembly. To do so,
stop the engine by removing the ignition key and loosen
the plastic wing knob found on the left side of the chute
assembly. Pivot the chute upward or downward before
Figure 6
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTAINING AND SERVICING YOUR SNOW THROWER
Auger Shaft
WARNING: Before lubricating, repairing, or
inspecting, disengage all controls and stop
engine. Wait until all moving parts have come
to a complete stop.
•
At least once a season, remove the shear pins on
auger shaft. Spray lubricant inside shaft, around
the spacers. Also lubricate the flange bearings
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine maintenance.
Shear Pin
Spacers
Bearing
Lubrication
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine lubrication
instructions.
Gear Shaft
The gear (hex) shaft should be lubricated at least once
a season or after every 25 hours of operation.
•
Remove the lower frame cover by removing the two
screws which secure it.
•
Apply a light coating of an all-weather multi-
Figure 8
Gear Case
The auger gear case has been filled with grease at the
factory. If disassembled for any reason, lubricate with
two ounces of grease (Part Number 737-0168).
IMPORTANT: Do not overfill the gear case. Damage to
the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
WARNING: Before servicing, repairing, or
inspecting, disengage all controls and stop
engine. Wait until all moving parts have come
to a complete stop.
Shave Plate and Skid Shoes
•
The shave plate and skid shoes on the bottom of
the snow thrower are subject to wear. They should
be checked periodically and replaced when
necessary.
Figure 7
IMPORTANT: Keep lubricant off the friction wheel and
drive plate.
•
To remove skid shoes, remove the four carriage
bolts and hex flange nuts which secure them to the
snow thrower. Reassemble new skid shoes with the
four carriage bolts (two on each side) and hex
flange nuts. Refer to Figure 4.
To remove shave plate, remove the carriage bolts
and hex nuts which attach it to the snow thrower
housing. Reassemble new shave plate, making
sure heads of carriage bolts are to the inside of
housing. Tighten securely.
Wheels
•
At least once a season, remove both wheels. Clean
and coat the axles with a multipurpose automotive
grease before reinstalling wheels.
•
Chute Directional Control
•
Once a season, the spiral end on the chute
directional control should be greased with
multipurpose automotive grease.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Belt Replacement
1
WARNING: Before servicing, disconnect
spark plug wire and ground it against the
engine to prevent unintended starting.
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
3. Roll the auger belt off the engine pulley.
4. Unhook the support bracket spring from the frame.
•
Loosen and remove the shoulder screw which acts
as a belt keeper.
•
Remove the belt from around the auger pulley, and
slip the belt between the support bracket and the
auger pulley
2
•
Reassemble auger belt by following instructions in
reverse order.
IMPORTANT: Do NOT forget to reinstall the shoulder
screw and reconnect the spring to the frame after
installing a replacement auger belt.
4
3
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Drive Belt Replacement
1
WARNING: Before servicing, disconnect
spark plug wire and ground it against the
engine to prevent unintended starting.
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
3.
a. Grasp the idler pulley and pivot it toward the
right.
b. Insert a screw driver through aligning holes in
both the idler bracket and the engine.
c. Roll the auger belt off the engine pulley.
d. Lift the drive belt off engine pulley.
2
4. Slip the drive belt off the pulley and between friction
wheel and friction wheel disc.
•
Remove and replace belt in the reverse order.
3
4
c
d
b
a
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Friction Wheel Removal
If the snow thrower fails to drive with the drive control
engaged, and performing the drive control cable
friction wheel may need to be replaced. Follow the
instructions below. Examine the friction wheel for signs
of wear or cracking and replace if necessary
1
2
3
•
•
Place the shift lever in third Forward (F3) position.
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
•
1.
a. Remove the frame cover from the underside
of the snow thrower by removing four self-
tapping screws which secure it.
b. Remove the right-hand wheel by removing
the screw and bell washer which secure it to
the axle.
c. Locate the hex shaft and E-ring on the right
side of the snow thrower frame, about two
inches from the wheel axle.
c. Using a suitable tool, carefully remove the
outer E-ring which secures the hex shaft to
the snow thrower frame and lightly tap the
shaft’s end to dislodge the ball bearing from
the right side of the frame.
2.
a. Slide the hex shaft downward and to the left
while carefully un-meshing the lower gears
on the hex shaft from the upper gears on the
wheel axle.
b. Set the hex shaft’s gears aside.
c. Carefully remove the inner E-ring from the
hex shaft and slide the friction wheel
assembly off the hex shaft.
NOTE: If you’re replacing the friction wheel assembly
as a whole, discard the worn part and slide the new part
onto the hex shaft. Follow the steps above in reverse
order to reassemble components. If you’re
disassembling the friction wheel and replacing only the
rubber ring, proceed as follows:
3. Remove the four screws which secure the friction
wheel’s side plates together.
•
•
Remove the rubber ring from between the plates.
Reassemble the side plates with a replacement
rubber ring.
IMPORTANT: Tighten each screw only one rotation
before turning the wheel clockwise and proceeding with
the next screw. Repeat this process several times to
ensure the plates are secured with equal force.
•
Slide the friction wheel assembly back onto the hex
shaft and follow the steps above in reverse order to
reassemble components.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: NEVER replace the auger shear pins with
anything other than OEM Part No.738-04124
replacement shear pins. Any damage to the auger
gearbox or other components as a result of failing to do
so will NOT be covered by your snow thrower’s
warranty.
Augers
•
The augers are secured to the spiral shaft with two
shear pins and cotter pins. If the auger should strike
a foreign object or ice jam, the snow thrower is
designed so that the pins may shear.
•
If the augers will not turn, check to see if the pins
have sheared. One set of replacement shear pins
has been provided with the snow thrower. When
replacing pins, spray an oil lubricant into shaft
before inserting new pins.
SECTION 7: OFF-SEASON STORAGE
•
Drain carburetor by pressing upward on bowl drain,
located below the carburetor cover.
WARNING: Never store the machine or
fuel container indoors where there is an open
flame, spark or pilot light such as on a water
heater, furnace, clothes dryer or other gas
appliances.
NOTE: Fuel stabilizers, such as STA-BIL®, are an
acceptable alternative in minimizing the formation of
fuel gum deposits during storage. Do not drain
carburetor if using a fuel stabilizer.
WARNING: Drain fuel into an approved
container outdoors, away from open flame.
Allow engine to cool. Extinguish cigarettes,
cigars, pipes, and other sources of ignition
prior to draining fuel. Fuel left in engine for
extended period deteriorates and will cause
serious starting problems.
•
•
Wipe equipment with an oiled rag to prevent rust.
Remove spark plug and pour one ounce of engine
oil through spark plug hole into cylinder. Cover
spark plug hole with rag. Crank engine several
times to distribute oil. Replace spark plug.
Follow the lubrication recommendations found in
the Maintenance Section.
•
•
If unit is to be stored over 30 days, prepare for storage
as follows:
Always store the snow thrower in a clean, dry area.
When storing any type of power equipment in an
unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.
•
Remove gasoline from carburetor and fuel tank to
prevent gum deposits from forming on these parts
and causing possible malfunction of engine.
Run engine until fuel tank is empty and engine
stops due to lack of fuel.
•
19
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: TROUBLE SHOOTING GUIDE
Trouble
Possible Cause(s)
Corrective Action
Engine fails to start
Fuel tank empty, or stale fuel.
Fill tank with clean, fresh gasoline. Fuel will not last over thirty days
unless a fuel stabilizer is used.
Blocked fuel line.
Clean fuel line.
Choke control not in ON position Move choke control to ON position
Faulty spark plug.
Clean, adjust gap or replace.
Ignition key not present.
Spark plug wire disconnected.
Engine not primed.
Insert key into ignition switch.
Connect spark plug wire.
Refer to the Tecumseh engine manual or Starting the Engine on page
10 of this manual for instructions on the engine primer.
Move choke control to OFF position.
Engine runs erratic
Loss of power
Unit running on CHOKE.
Blocked fuel line or stale fuel.
Clean fuel line; fill tank with clean fresh gasoline. Fuel will not last
over thirty days unless a fuel stabilizer is used.
Drain fuel tank. Refill with fresh fuel.
Refer to the Tecumseh engine manual.
Connect and tighten spark plug wire.
Remove ice and snow from cap. Be certain vent hole is clear.
Clean following the engine manual.
Refer to the Tecumseh engine manual packed with your unit or
have carburetor adjusted by an authorized service dealer.
Water or dirt in fuel system.
Carburetor out of adjustment.
Spark plug wire loose.
Gas cap vent hole plugged.
Exhaust port plugged.
Carburetor not adjusted
properly.
Engine overheats
Excessive vibration
Loose parts or damaged auger. Stop engine immediately and disconnect spark plug wire. Tighten
all bolts and nuts. Make all necessary repairs. If vibration
continues, have unit serviced by an authorized service dealer.
Unit fails to propel itself Incorrect adjustment of drive
control cable.
Adjust drive control cable.
Drive belt loose or damaged.
Replace drive belt.
Unit fails to
discharge snow
Chute assembly clogged.
Stop engine immediately. Clean chute assembly and inside of
auger housing with chute clean-out tool
Foreign object lodged in auger. Stop engine immediately. Remove object from auger.
Incorrect adjustment of auger
control cable.
Adjust auger control cable.
Drive belt loose or damaged.
Replace drive belt.
NOTE: For repairs beyond the minor adjustments above, contact your local authorized service dealer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles C & D
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
Handle Ass’y, Engagement RH Black
Handle Ass’y, Engagement, LH Black
Screw, Self-tapping, 5/16-12, 0.750
Screw, Machine, #10-24, 1.375
Screw, #8-18 x .375
684-04106A
684-04105A
710-0726
710-1233
710-04164
712-0161
712-04063
712-04064
714-0104
Nut, Hex Lock, #10-24, Gr2, Nylon
Nut, Flange Lock, 5/16-18, Grf, Nylon
Nut, Flange Lock, 1/4-20, Grf, Nylon
Pin, Cotter, .072 x 1.13
Grip, 1.0 ID x 5.0
8
9
10 720-0274
11 710-04354
12 711-04287
13 631-04134
14 631-04133
15 732-04219
16 731-04896
17 735-0199A
18 731-04894
19 747-1136
20 738-04122
21 746-0778
22 725-1658
23 725-1672
24 725-04220
25 747-04263
26 790-00100
790-00101
27 684-04104
28 710-0449
29 712-04081A
30 720-0284
31 720-0201A
32 726-0100
33 735-0234
34 736-0185
35 736-0451
36 749-04138
37 749-04141
38 749-04142
39 710-0606
40 732-04238
41 710-0376
42 720-0223
43 747-04243
44 790-00099
45 732-04205
46 790-00156
Screw, 1/4-20, .375
Rod, Pivot
Handle, Clutch Lock, RH
Handle, Clutch Lock, LH
Spring, Control Lever Lock
Cam, Lock
Bumper, Rubber, .62 OD x .22
Plate, Lock
Retainer, Lens
Screw, Shoulder, .437 x 1.345, 1/4-20
Z Fitting, Cable
Lamp, Halogen, 12V, 27W
Lens Assembly, Lamp
Harness, Headlight
Eye Bolt, Chute Crank
Panel, Handle, C-Style
Panel, Handle (w/ Cutout), D-Style
Crank Assembly, Chute
Screw, Carriage, 5/16-18, 2.25, Gr5
Shoulder Nut, Hex, 1/4-20
Knob Assembly, Wing Nut, 5/16-18
Crank Knob, 1.0 Diameter x 3.2, Black
Cap, Push, 3/8 Rod
Grommet, .44 ID x .94 OD x .50
Washer, Flat, .375 x .738 x .063
Washer, Saddle, 320 x .93 x .060
Handle, Lower, Snow
Handle, Upper, RH
Handle, Upper, LH
Screw, Hex, 1/4-20 x 1.5
Spring, Torsion, .8156 x .3038
Screw, 5/16-18 x 1.0
Grip
Lever, Shift
Panel, Speed Selector (5 FW, 2 RV)
Spring, Shift Lever
Bracket, Shift Spacer
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles C & D
38
8
4
41
37
1
63
36
40
16
6
9
22
3
13
42
18
64
43
61
5
41
8
15
26
24
14
7
9
23
17
12
21
4
2
8
4
6
28
35
44
7
45
8
28
53
52
56
59
62
57
54
48
58
55
47
60
49
51
25
46
50
32
30*
27
33
31
34
27
29
33
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles C & D
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
33 741-0493A
34 790-00087
35 790-00117
790-00120
PART
NO.
DESCRIPTION
Clean Out Tool
DESCRIPTION
Bushing, Flange, .800 ID x .910 OD
Housing, Bearing, 1” Hex
Plate, Shave, 2.25 x 21.66
Plate, Shave, 2.25 x 23.66
Plate, Shave, 2.25 x 25.66
Plate, Shave, 2.25 x 27.66
Bolt, Carriage, 5/16-18, 1.0
Knob Assembly
731-2643
684-04057
710-0347
710-0451
710-0703
710-0726
712-04063
712-04064
712-04065
Impeller Assembly, 12” Diameter
Hex Screw, 3/8-16, 1.75, Gr5, Std
Bolt, Carriage, 5/16-18, .750 Gr1
Screw, Carriage, 1/4-20, .75, Gr5
Screw, Self-tapping, 5/16-12, 0.750
Nut, Flange Lock, 5/16-18, Grf, Nylon
Nut, Flange Lock, 1/4-20, Grf, Nylon
Nut, Flange Lock, 3/8-16, Grf, Nylon
Internal Cotter Pin
790-00121
790-00118
36 710-04071
37 720-04032
38 731-04426A Chute, Upper, w/ Domestic Label
8
9
10 714-0149B
11 725-0157
12 726-04012
13 731-04705
14 732-0611
15 736-0174
16 731-2635
17 738-0143
18 738-0281
19 738-04124
20 741-0245
21 741-0309
22 756-0981A
23 790-00075
24 790-00080
25 618-04170
618-04171
39 731-04869
40 731-04912
41 736-0159
42 741-0475
43 784-5647
44 784-5580
45 719-0319
46 719-0320
47 721-0179
48 741-0662
49 710-0642
50 711-04286
711-04285
Chute, Keeper Flange
Chute, Lower, 5.0 Diameter
Washer.349 ID x .879 OD x .063
Bushing, Plastic, .380
Bracket, Chute Crank
Shoe, Slide
Housing, Auger, RH Reduced
Housing, Auger, LH Reduced
Seal, Oil, .750 ID
Bearing, Flange, .75 ID x 1.00 OD x .59
Screw, Self-tapping, 1/4-20, 0.750
Axle, Auger, 22"
Axle, Auger, 24"
Axle, Auger, 26"
Axle, Auger, 28"
Key, Hi-pro 3/16 x 5/8
Pin, Dowel, .25 OD x 1.2
Shaft, Worm .75 OD
Gear, Worm 20T
Collar, Thrust
Plug, 1/4 x .437
Cable, Tie, 3/16 x .05 x 7.4
Nut, Push-on, .25 Diameter
Chute, Adapter 5” Diameter
Spring, Extension, .38 OD x 3.6
Washer, Wave, .625 x.885 x.015
Mount, Clean Out Tool
Screw, Shoulder, .498 x .340, 3/8-16
Screw, Shoulder, .625 x .170, 3/8-16
Pin, Shear, .25 x 1.50, Gr2
Bearing, Hex Flange x .75 ID
Bearing, Ball, .75 ID x 1.85 OD
Idler Pulley, Flat 2.75 OD
Housing, Bearing, 1.85 ID
711-04284
711-04283
Bracket, Auger Idler w/ Brake
Gearbox Assembly, Auger, 22”
Gearbox Assembly, Auger, 24”
Gearbox Assembly, Auger, 26”
Gearbox Assembly, Auger, 28”
Housing Assembly, Auger 22”
Housing Assembly, Auger 24”
Housing Assembly, Auger 26”
Housing Assembly, Auger 28”
Spiral Assembly, LH
Spiral Assembly, RH
Bow-Tie Cotter Pin
Spacer, 1.25 OD x .75 ID x 1.00
Washer, Flat, .76 x 1.49 x .06
Shear Pin, .25 x 1.50, Gr2
51 714-0161
52 715-04021
53 717-04126
54 717-0528A
55 718-04071
56 721-0325
57 721-0327
58 736-0351
59 736-3084
60 741-0663
61 746-0897
62 741-0661A
63 629-0071
64 710-0726
618-04172
618-04173
26 684-04067
684-04069
684-04071
684-04073
Seal, Oil, .75 x 1 x .131
Washer, Flat, .760 ID x 1.5 OD
Washer, Flat, .51 x 1.12
Bearing, Flange, .75 ID x 1.00 OD x .925
Auger Clutch Cable, 44.75”
Bearing, Flange, .75 ID x 1.00 OD x .975
Cord, Extension
27 684-04107
28 684-04108
29 714-04040
30 731-04870*
31 736-0188
32 738-04124
Bolt, Carriage, 5/16-18, 1.0 Gr1
* None found between spirals on models with 22-inch auger housing.
* One found between spirals on models with 24-inch auger housing.
* Two found between spirals on models with 26-inch auger housing.
* Three found between spirals on models with 28-inch auger housing.
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles C & D
58
55
41
46
17
50
7
9
58
53
7
57
47
52
49
40
59
54
56
44
45
51
43
48
9
39
21
7
20
24
30
6
24
13
29
16
18
36
27
12
1
14
15
34
2
28
35
26
24
14
9
4
3
10
22
33
32
19
23
11
5
42
8
20
7
31
9
9
37
28
25
38
4
9
63
62
61
65
64
60
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles C & D
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
PART
NO.
DESCRIPTION
Gear Assembly, 16/44T
Gear Assembly, 16/44T
Disc Assembly, Friction Wheel, .375
Wheel Assembly, Friction, 4.9 OD
Support Bracket Ass’y, Friction Wheel
Shift Assembly, Rod
Screw, 5/16-24 x .750, Gr5
Screw, 1/4-20 x 1.000
DESCRIPTION
Spacer, .508 ID x .75 OD x .68
Roller, Cable
Guide Bracket, Auger Cable
Frame
617-04026
617-04025
656-0012A
684-04066
684-04045
684-04139
710-0627
710-0788
710-1652
33 748-0190
34 756-0625
35 784-5687A
36 790-00072
37 790-00096
38 790-00054
39 790-00055
40 710-0191
41 710-0597
42 710-0654A
43 710-1245B
44 712-04064
45 731-04792
46 732-0710
47 736-0247
48 736-0505
49 741-0919
50 748-0234
51 748-04053
52 750-04230
53 750-04303
54 754-04050
55 754-0456
56 756-04109
57 756-04113
58 756-04114
59 790-00062
60 790-00010
61 790-00011
62 710-0896
63 618-04169
64 718-04070
65 735-0243B
Guide Bracket, Front, Auger Cable
Cover, Frame
Roller Bracket, Drive Cable
Screw, 3/8-24 x 1.25, Gr8
Screw, 1/4-20 x 1.00, Gr5
Screw, Sems, 3/8-16 x 1.00
Screw, 5/16-24 x .875, Gr8
Nut, Flange Lock, Nylon, 1/4-20, GrF
Cover, Belt
Spring, Extension, .38 OD x 2.68
Washer, Flat, .406 x 1.25 x.157
Washer, Flat, .34 x 1.50 x .150
Bearing, Ball, 20 x 47 x 14
Shoulder Spacer
Pulley, Adapter, .75 Dia.
Spacer, .777 OD x .260 ID x.550
Spacer, .875 ID x 1.185 OD
V-Belt, 1/2”
V-Belt, 3/8”
Pulley, Auger, 8.1 x .50
8
9
Screw, 1/4-20 x .625
10 711-04246A Hex Shaft, Drive, .75
11 712-0711
12 714-0161
13 716-0231
14 716-0136
15 717-04129A Pinion, 16T
16 717-04137A Gear, 44T
17 790-00082
18 726-0221
19 732-0264
20 736-0242
21 736-04161
22 736-0300
23 736-0105
24 736-0287
25 See Chart
26 731-04873
731-04877*
Nut, Jam, 3/8-24, Gr2
Key, Hi-pro 3/16 x 5/8
Ring, E Type, .750
Ring, E-Type, .875
Idler, Bracket, Drive
Nut, Speed, .500
Extension Spring
Washer, Bell, .340 x .872 x .060
Washer, Flat, .75 x 1.00 x .060
Washer, Flat, .406 x .875 x .059
Washer, Bell, .375 x .870 x .063
Washer, Flat, .793 x 1.24 x .060
Wheel Assembly, Complete
Spacer, 1.25 OD x .75 ID x 3.00
Spacer, 1.25 OD x .75 ID x 1.50
Pulley, Half, 2.600 OD
Pulley, Half, 2.2 OD
Washer, Bearing, 2.12 OD x .255 ID
Plate, Friction, 12 Pt 4.60 Dia
Plate, Friction, Extrs, 12 Pt 4.60 Dia
Screw, Self-tapping, 1/4-14 x 0.625
Bearing Assembly, Friction Wheel
Hub, Friction Wheel
27 738-04095A Axle, .75 x 22
28 738-0924
29 741-0563
30 741-0245
31 746-0897
32 746-04086
Screw, 1/4-28 x .375
Bearing, Ball, 17 x 40 x 12
Bearing, Hex Flange x .75 ID
Cable, Auger, 44.75
Cable, Drive, 41.75
Friction Wheel Rubber, 4.875 OD
* Found on models with a 22-inch auger housing only.
Wheel Assembly
Complete
Wheel Size
Rim Only
Tire Only
Air Valve
634-04144
634-04143
634-04142
634-04141
13 x 4
13 x 5
15 x 5
16 x 4.8
634-04151
634-04151
634-04151
634-04140
734-1732
734-1527
734-1859
734-1530
734-0255
734-0255
734-0255
734-0255
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured on the previous page
are standard equipment.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the
United States, its possessions and territories.
e.
MTD does not extend any warranty for products sold or
exported outside of the United States, its possessions
and territories, except those sold through MTD’s
authorized channels of export distribution.
Replacement parts that are not genuine MTD parts.
Transportation charges and service calls.
“MTD”warrants this product against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
materials or workmanship. This limited warranty shall only
apply if this product has been operated and maintained in
accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this
manual will void your warranty as to any resulting damage.
f.
g.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind MTD. During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. MTD
shall not be liable for incidental or consequential loss or
damage including, without limitation, expenses incurred
for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted
product.
Normal wear parts are warranted to be free from defects in
material and workmanship for a period of thirty (30) days from
the date of purchase. Normal wear parts include, but are not
limited to items such as: batteries, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow thrower
skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-
330-220-4683 or log on to our Web site at
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty does not provide coverage in the
following cases:
a.
The engine or component parts thereof. These items
may carry a separate manufacturer’s warranty. Refer
to applicable manufacturer’s warranty for terms and
conditions.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
b.
c.
Log splitter pumps, valves, and cylinders have a
separate one year warranty.
HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
deterioration of the exterior finish due to use or
exposure.
IMPORTANT: Owner must present Original Proof of
Purchase to obtain warranty coverage.
d.
Service completed by someone other than an
authorized service dealer.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683
Download from Www.Somanuals.com. All Manuals Search And Download.
|