| 
		 Metra Electronics Musical Instrument Amplifier 99 7319 User Manual  | 
	
| 	
		 INSTALLATION INSTRUCTIONS FOR PART 99-7319   
					APPLICATIONS   
					2004-2006 Kia Amanti   
					99-7319   
					KIT FEATURES   
					• DIN Head Unit Provision   
					• ISO DIN Head Unit Provision   
					KIT COMPONENTS   
					A) Radio Housing B) A/C Control Brackets C) ISO Brackets D) Trim plate   
					A 
					B 
					D 
					C 
					TOOLS REQUIRED:   
					Phillips Screwdriver I Small Flat Blade Screwdriver   
					1-800-221-0932   
					
					© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				DASH DISASSEMBLY   
					99-7319   
					2004-2006 KIA AMANTI   
					A 
					Disconnect the negative battery   
					terminal to prevent an accidental   
					short circuit.   
					1 
					2 
					Unclip and remove panel surround-   
					ing shifter including cup holders.   
					(Figure A)   
					Remove (2) Phillips screws at base   
					of panel surrounding radio and a/c   
					controls. (Figure B)   
					3 
					4 
					Unclip and remove panel surround-   
					B 
					ing radio and a/c control. (Figure C)   
					C 
					1 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				DASH DISASSEMBLY   
					99-7319   
					2004-2006 KIA AMANTI   
					D 
					5 
					6 
					Remove (6) Phillips screws securing   
					radio and a/c control. (Figure D)   
					Remove (4) Phillips screws securing   
					factory a/c control to bracket assem-   
					bly. (Figure E)   
					VOL   
					LOAD   
					E 
					2 Phillips screws on each side   
					2 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				KIT ASSEMBLY   
					99-7319   
					2004-2006 KIA AMANTI   
					DIN HEAD UNIT PROVISION   
					A 
					Attach the corresponding a/c control   
					1 
					bracket to the factory a/c control   
					using the factory hardware. (Figure A)   
					Note: The radio housing must be   
					installed first before the a/c control.   
					Slide the DIN cage into the radio   
					housing and secure by bending the   
					metal locking tabs down. (Figure B)   
					1 
					2 
					B 
					Slide the aftermarket head unit into   
					the cage and secure. (Figure C)   
					C 
					3 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				KIT ASSEMBLY   
					99-7319   
					2004-2006 KIA AMANTI   
					ISO DIN HEAD UNIT PROVISION   
					A 
					Attach the corresponding a/c control   
					bracket to the factory a/c control   
					1 
					using the factory hardware. (Figure A)   
					Note: The radio housing must be   
					installed first before the a/c control.   
					Mount the ISO bracket to the head   
					1 
					unit with screws supplied with the   
					unit. (Figure B)   
					B 
					Slide the head unit into the radio   
					opening until the side clips engage.   
					(Figure C)   
					2 
					Snap the trim plate into the radio   
					3 
					housing. (Figure C)   
					C 
					4 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				FINAL ASSEMBLY   
					99-7319   
					FINAL ASSEMBLY   
					A 
					B 
					A)   
					B)   
					C)   
					D)   
					Strip wire ends back 1/2"   
					Twist ends together   
					Solder   
					Tape   
					C 
					D 
					Locate the factory wiring harness in the dash. Metra recommends using the   
					proper mating adapter and making connections as shown.   
					(Isolate and individually tape off the ends of any unused wires to prevent   
					electrical short circuit.)   
					1 
					Re-connect the negative battery terminal and test the unit for proper operation.   
					2 
					3 
					Reassemble radio and dash assemblies in reverse order of disassembly   
					installing the radio housing first and then the a/c control.   
					FINAL WIRING CONNECTIONS   
					Make wiring connections using the EIA color code chart shown below and the instructions included with the head   
					unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually   
					tape off ends of any unused wires to prevent electrical short circuit.   
					METRA / EIA WIRING CODE   
					12V Ignition / Acc . . . Red   
					Right Front (+) . . . . . Gray   
					12V Batt / Memory . . Yellow   
					Ground . . . . . . . . . . . Black*   
					Power Antenna . . . . . Blue   
					Right Front (-). . . . . . Gray / Black   
					Left Front (+) . . . . . . White   
					Left Front (-). . . . . . . White / Black   
					Right Rear (+). . . . . . Violet   
					Amp Turn-On . . . . . . Blue / White   
					Amp Ground . . . . . . . Black / White   
					Illumination. . . . . . . . Orange   
					Dimmer . . . . . . . . . . Orange / White   
					Right Rear (-) . . . . . . Violet / Black   
					Left Rear (+). . . . . . . Green   
					Left Rear (-) . . . . . . . Green / Black   
					*NOTE: When Black a wire is not present, ground radio to vehicle chassis.   
					All colors may not be present on all leads due to manufacturer’s specifications.   
					5 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				99-7319 INSTRUCTIONS   
					1-800-221-0932   
					
					REV. 06/19/2007   
					© COPYRIGHT 2004-07 METRA ELECTRONICS CORPORATION   
					INST99-7319   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				 |