INSTALLATION INSTRUCTIONS FOR PART 95-7427
APPLICATIONS
Nissan Maxima 2009-11
w/o Navigation or Technology Package
95-7427B/
95-7427G
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• PAINTED TO MATCH FACTORY DASH:
95-7427B=BLACK, 95-7427G=GRAY
• Textured To Match Factory Dash
KIT COMPONENTS
• A) Double DIN Radio Housing
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
1-800-221-0932
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427 DASH DISASSEMBLY
NISSAN MAXIMA 2009-11
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
2
Unclip and remove the panel above
the radio including the a/c vents and
the climate controls. Unplug and
remove the panel. (Figure A)
X
3
4
Unclip and remove the panel below
the radio. (Figure B)
Remove (6) Phillips screws securing
the radio. Unplug and remove the
radio. (Figure C)
5
Remove (5) Torx head screws secur-
ing each side bracket to factory radio
and remove brackets and module.
(Retain brackets, module and (2)
screws from module for re-use during
kit assembly.) (Figure D)
Continued on page 2.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION OR
STACKED ISO MOUNT UNIT(S) PROVISION
*Note: Refer also to the instructions included with the aftermarket radio.
1
Attach the factory brackets and mod-
ule to the Double DIN or stacked ISO
mount unit(s) with the screws supplied
with the unit(s) and (2) screws from
Continue to final assembly.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427 FINAL ASSEMBLY
FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
C
D
D) Tape
Locate the factory wiring harness in the dash. Metra recommends using the proper mating
adapter and making the connections as shown. (Isolate and individually tape off the ends of
any unused wires to prevent electrical short circuit).
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.
Position the factory bracket/aftermarket radio assembly into the dash and secure using
the factory hardware.
Secure the Double DIN radio housing to the sub dash using the factory hardware.
Reassemble the rest of the dash in reverse order of disassembly.
4
5
Make wiring connections using the EIA color code chart shown below and the instructions
included with the head unit. Metra recommends making connections shown below; Strip, Splice,
Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
Right Front (+) . . . . . . . . . . . . Gray
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be
present on all leads due to manufacturer’s specifications.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427
NOTES
4
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427
NOTES
5
Download from Www.Somanuals.com. All Manuals Search And Download.
95-7427 INSTRUCTIONS
1-800-221-0932
REV. 10-06-10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-7427
Download from Www.Somanuals.com. All Manuals Search And Download.
|