V o y a g e r
T r a v e l
I r o n
Model:
2 3 1 0 1
1000W
PLEASE READ ALL INSTRUCTIONS BEFORE USE
2 y e a r g u a r a n t e e
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 1
3/6/2009 9:30:18 AM
KEY and CHARACTERISTICS
3
2
5
6
4
8
7
1
Description
1
2
3
4
5
6
7
8
Filling apeture for water tank
Revolving handle
Spray / Vapour jet knob
Revolving handle lock
Temperature regulator
Control lamp
Voltage changeover switch
Spray nozzle
Dry/Steam selector knob
Voltage changeover switch
CHARACTERISTIC
Temperature Dial Knob
Power Indicator Light
FUNCTION
Adjust temperature according to fabric to be ironed.(see table below)
Indicator light will go off when desired temperature is reached. The light will go on
and off as the temperature is regulated by the adjustable thermostat.
Super smooth non stick ironing surface. If ironing surface is sticky ensure
temperature setting is correct as per table below and item being ironed is clean.
Using the measuring cup only, fill the tank with clean water here. Use demineralized
water in hard water areas or water with lime scale.
Soleplate
Water Filling Aperture
Transparent Water Tank
Dry/Steam Iron Selector
Spray Button
Do not overfill. Water level in tank is easily visible during ironing.
Choose desired level of steam or dry ironing by sliding the knob
Depress for spraying water onto fabric for dry ironing or when required.
Use this switch to change between 115V or 230V
Voltage changeover
switch
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 3
3/6/2009 9:30:19 AM
Note* Do not fill higher than indication “MAX”
of the water tank, In order to avoid spilling out
of water.
IRONING INSTRUCTIONS
Note: The iron may smoke slightly when
switched on for the first time. This is normal
and will soon cease.
-
Do not fill with any thing but clean water. If you
have to refill while ironing, remove the mains
plug from the wall socket before filling.
Pour out any remaining water after use.
Please read these instructions carefully before
use.
-
Important!: have you read the section “Impor
tant Safeguards”?
SETTING THE TEMPERATURE
-
Insert the plug in the wall socket and stand the
iron upright.
CHOICE OF WATER
-
Set the temperature control dial to the correct
temperature as indicated in the ironing
instructions on the label or as per table above.
The correct temperature will be reached when
the indication light has gone. The indication
light will be on and off from time to time
indicating that the selected temperature is being
maintained.
-
-
This iron can be used with normal tap water.
If the water in your area is particularly hard. It
is advisable to use distilled or demineralized
water to prevent the scale forming on the
critical point of the iron.
-
-
Do not use chemically de-scaled water.
FILLING WITH WATER
-
-
-
Ensure that the iron is disconnected from the
power supply before filling.
Note: Water may leak from the soleplate if the
temperature selected is too low.
Turn the dry/steam selector dial to “0” or dry
position.
This will then cause stains. If it happens, Set the
temperature control to the advised position for
steam ironing. Steaming will re-commence as
soon as the appropriate temperature has been
reached.
Fill water through the aperture using the
measuring cup only. (If you fill the iron at the
tap water can spill into the electrics and trip
your earth leakage or blow the iron.)
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 4
3/6/2009 9:30:19 AM
SPRAYING
CARE AND CLEANING
-
At any temperature by pressing on the spray
•
•
•
Before cleaning the iron, ensure it is
disconnected from the power supply and has
completely cooled down.
button a couple of times, the laundry can be
damped down.
-
Ensure that there is enough water in the water
tank.
Deposits and other residues on the soleplate
can be removed with a rough cloth soaked in a
vinegar/water solution.
The housing/body may be wiped with a damp
cloth and then polished with a dry one.
Dot not use abrasives on the soleplate.
Keep the soleplate smooth: avoid hard contact
with metal objects.
•
•
•
NOTE: Ironing dirty fabric or fabric not rinsed
fully will result in the iron sticking and dirt
accumulating on the bottom of the soleplate, as
will a iron set at too high a temperature for the
relevant fabric.
PACKING THE IRON BEFORE TRAVELING
•
•
•
Let the iron cool down completely.
DRY IRONING
Empty the water tank.
•
•
Insert the main plug into the wall socket.
Ensure that the dry/steam selector button (C) is
in position“0”.
Press the unlock button and fold handle to the
side.
•
•
Select the setting on the temperature control
dial best suited for the fabric to be ironed.
When the indication light has gone out, ironing
may commence.
STORAGE
•
Turn the temperature control dial to “MIN” and
set the steam selector dial to position “0”. (“0”
=No Steam).
•
•
Disconnect the plug from the wall socket.
Pour any remaining water out of the water tank.
Then cover the filler cap.
STEAM-IRONING
•
As indicated on the temperature control dial
and the temperature table, steam ironing is only
possible at higher ironing temperature:
Ensure that there is enough water in the water
tank.
•
Stand the iron upright and let it cool down
sufficiency.
•
•
•
The power cord can be wound around the iron.
Press the unlock button and fold the handle to
the side.
•
•
•
Stand the iron on its rear side.
Insert the plug into the wall socket.
Set the temperature control dial to the steam
position.
•
•
Wait a little while for the power indication light to
go out and to come on again.
Set the dry/steam selector knob to the steam
position. The steam will emerge from the vents
in the soleplate when the iron is held in the
horizontal position.
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 5
3/6/2009 9:30:19 AM
6. If you leaving the appliance momentarily always
switch it off, remove the plug from the wall
socket and stand the iron on its base.
7. Take care that children cannot touch the iron
when the iron is hot and make sure they cannot
pull the mains cord.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Note: When using the iron for the first time,
testing on an old piece of fabric to ensure that
the soleplate and water tank is completely
clean.
8. To protect against the risk of electric shock, do
not immerse the iron, cord or plug in water or
other liquids.
SAFETY PROTECTIVE CUT – OUT
In the unlikely event of the thermostat failing, the
protection cut – out will operate to prevent the iron
overheating. The iron should then be taken to an
authorized dealer/service agent for repair.
9. Burns can occur from touching hot metal parts,
hot water or steam, Be caution when you turn
a steam iron upside down: there may be hot
water in the tank.
10.Do not allow the mains cord to touch hot
surface. Let the iron cool down completely
before taking it away. Wind the main cord
around the iron when storing.
IMPORTANT SAFEGUARDS
1. Please read all instructions before use.
2. Ensure the voltage rating on the type plate
corresponds to the main voltage in your home.
3. Use the iron only for its intended use.
4. The iron should always be switched off before
connecting or disconnecting from the power
supply. Never yank/pull the cord to disconnect
the plug from the wall socket.
11.Always disconnect the main plug from wall
socket before filing the iron with water or
pouring the remaining water out.
12.To avoid an overloaded circuit, do not operate
another high voltage appliance in the same
electric circuit.
13.If an extension cord is absolutely necessary, a
10-ampere (Europe) or 15 ampere (America)
cord should be used. Cords rated for less
amperage may overheat. Care should be taken
to arrange the cord so that it cannot be pulled or
tripped over.
5. Do not operate the iron with a damaged cord
or plug. Never use the iron if it is damaged in
any way. To avoid the risk of electric shock, do
not re-assemble the iron. Take it to a qualified
serviceman for examination and repair. Incorrect
re-assembling can cause electric shock when
the iron is used.
14.This iron is for household use only.
15. Traveling irons are not intended for normal use.
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 6
3/6/2009 9:30:19 AM
TROUBLE SHOOTING
Problem
Reason
Action
Pre-caution
Iron is leaking water.
Temperature is too low
Set the temperature to steam setting (cotton)
Check fabric type is suitable for high steam
temperature
Steam switch is on self clean
function
Turn steam switch setting to steam or 0
position
Switch steam setting to 0 (off) after use or
when filling tank.
Tank is overfilled
Empty water tank
Fill to MAX mark only.
Iron is in the horizontal position
too long.
When adjusting item place iron down in the
vertical position
If iron is left on the item in the horizontal
position for too long it may burn the fabric.
Check temperature setting is suitable for
fabric type.
Iron is not heating up
Temperature control dial is in
the off position
Turn the temperature control dial to the
desired temperature setting.
Switch on household socket
Check the socket with another appliance
Household socket is off.
Household socket is not
working
Ensure iron is in the upright position.
Appliance must be of similar wattage to
prevent overloading.
Iron is tripping mains
Overloaded circuit.
Unplug all appliances attached to the same
circuit and check iron.
Note that there can be up to 5 household
plug sockets on 1 circuit.
Iron sticking to clothing
Temperature is too hot
Turn down temparature on control dial.
Clean and rinse item.
Check temperature setting is suitable for
fabric type.
Clothing is dirty or not rinsed
thoroughly.
Use spray function to dampen item and
check temperture is correct.
Use a old linen cloth to remove any trace
of dirt on the soleplate. Use iron soleplate
cleaner for bad marks.
Creases not coming out
Not Enough Steam
Item is too dry or temperature
too low.
Use steam function.
Check temperature setting is suitable for
fabric type.
The steam control is off or set
too low.
Set the steam button/switch to on or full.
Ensure temperature control dial is set to the
3 dot position for steaming.
Check temperature setting is suitable for
fabric type.
The iron temperature is
too low.
Set temperature control dial to MAX or 3 dot
position for steaming.
The steam valve is blocked
due to water scale.
If your iron is fitted with a self clean function
carry out cleaning as per instructions.
Use distilled or demineralised water in your
iron to prevent blocking.
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 7
3/6/2009 9:30:19 AM
27 Nourse
Avenue Epping
2
Cape Town
P.O. Box 975 Eppindust 7475 South Africa
Tel: +27 21 534 8114 Fax: +27 21 534 8086
Service Centre Share Call: 086 111 5006
w e b : w w w. c r e a t i v e h o u s e w a r e s . c o . z a
Download from Www.Somanuals.com. All Manuals Search And Download.
MW_CO23101 Voyager_IM.indd 8
3/6/2009 9:30:19 AM
|