Bottom Freezer
Use & Care Guide
Guía de uso y cuidado en español . . . . . . . . . . . . . . . . . 22-43
Guide d’utilisation et d’entretien français . . . . . . . . . . . 44-65
Benutzungs- und Pflegeanleitungen – Deutsch . . . . . . 66-87
Italiano – Guida all’uso e alla manutenzione . . . . . . . . 88-109
∂ÏÏËÓÈΤ˜ Ô‰ËÁ›Â˜ ¯Ú‹Û˘ Î·È ÊÚÔÓÙ›‰·˜ . . . . . . . . . 110-131
Guia de Uso e Cuidado em Português . . . . . . . . . . . . .132-153
Nederlandse gebruiks- en onderhoudshandleiding . .154-175
Dansk betjeningsvejledning . . . . . . . . . . . . . . . . . . . . . 176-197
Svensk manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .198-219
Suomenkielinen käyttö- ja huolto-ohje . . . . . . . . . . . 220-241
Norsk bruks- og vedlikeholdsanvisning . . . . . . . . . . 242-263
Türkçe Kullanım ve Bakım Kılavuzu . . . . . . . . . . . . . . .264-287
Important Safety Instructions . . . . . . . . 1-2
Installation . . . . . . . . . . . . . . . . . . . . . . . 3-7
Temperature Controls . . . . . . . . . . . . . . . . 8
Fresh Food Features . . . . . . . . . . . . . . . 9-11
Freezer Features . . . . . . . . . . . . . . . . . . . . 12
Food Storage Tips . . . . . . . . . . . . . . . . . . 13
Care and Cleaning . . . . . . . . . . . . . . . 14-17
Operating Sounds . . . . . . . . . . . . . . . . . . 18
Troubleshooting . . . . . . . . . . . . . . . . . 19-21
Part No. 12828113
Litho U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING
To reduce risk of fire, electric shock, serious injury or
death when using your refrigerator, follow these basic
precautions, including the following:
13. Install refrigerator according to Installation
Instructions. All connections for water, electrical
power and earthing must comply with local codes
and be made by licensed personnel when required.
1. Read all instructions before using the refrigerator.
2. Observe all local codes and ordinances.
3. Be sure to follow earthing instructions.
14. Keep your refrigerator in good condition. Bumping
or dropping refrigerator can damage refrigerator or
cause refrigerator to malfunction or leak. If damage
occurs, have refrigerator checked by qualified
service technician.
4. Check with a qualified electrician if you are not sure
this appliance is properly earthed.
15. Replace worn power cords and/or loose plugs.
5. Do not earth to a gas line.
16. Always read and follow manufacturer’s storage and
ideal environment instructions for items being stored
in refrigerator.
6. Do not earth to a cold-water pipe.
7. Refrigerator is designed to operate on a separate
220-240 volt, 10 amp., 50 HZ cycle line.
17. Your refrigerator should not be operated in the
presence of explosive fumes.
8. Do not modify plug on power cord. If plug does not
fit electrical outlet, have proper outlet installed by a
qualified electrician.
18. Children should not climb, hang or stand on any
part of the refrigerator.
9. Do not use a two-prong adapter, extension cord or
power strip.
19. Clean up spills or water leakage associated with
water installation.
10. Do not tamper with refrigerator controls.
20. The appliance is not intended for use by young
children or infirm persons without supervision.
11. Do not service or replace any part of refrigerator
unless specifically recommended in Use & Care
Guide or published user-repair instructions. Do not
attempt service if instructions are not understood or
if they are beyond personal skill level.
21. Young children should be supervised to ensure that
they do not play with the appliance.
12. Always disconnect refrigerator from electrical supply
before attempting any service. Disconnect power
cord by grasping the plug, not the cord.
Installing Your Refrigerator
These instructions were provided to aid you in the installation of your unit. The manufacturer cannot be responsible
for improper installation.
Steps to Follow...
A qualified engineer must connect refrigerator in accordance with these installation instructions.
Measure door opening and depth and width of refrigerator. Remove handles or doors if required. Engineer must
also do the following:
1. Follow local water and electrical company connection regulations.
2. Complete water supply connection before electrical supply connections.
Service to or replacement of power cord must be performed by a qualified engineer.
Note
When writing or calling about a service problem, please include the following information:
a. Your name, address and telephone number;
b. Model number and serial number;
d. A clear description of the problem you are having;
e. Proof of purchase (sales receipt)
c. Name and address of your dealer or engineer;
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Location
• Do not install refrigerator near oven, radiator or other
heat source. If not possible, shield refrigerator with
cabinet material.
WARNING
To be done by a qualified engineer only.
Your refrigerator was packed carefully for shipment.
Remove and discard shelf packaging and tape. Do not
remove the serial plate.
• Do not install where temperature falls below 13° C or
rises above 95° C. Malfunction may occur at this
temperature.
Measuring the Opening
When installing your refrigerator, measure carefully.
One-half inch (1.3 cm) of air space should be provided
for the top and back of the refrigerator.
• Refrigerator is designed for indoor household
application only.
How to Remove and Replace
Door and Hinges
Note: 60 cm deep models
Trim corners of countertop to a 45° angle if
countertop has 25 mm overhang. Provide 5 mm
clearance on both sides of refrigerator, and allow
7 mm on top for ease of installation and leveling.
No minimum clearance is required at the rear of the
cabinet.
WARNING
Contact a qualified engineer to perform this task.
How to Connect the Water
Supply (select models)
WARNING
Contact a qualified engineer to perform this task.
Subflooring or floor coverings (i.e. carpet, tile, wood
floors, rugs) may make your opening smaller than
anticipated.
Some clearance may be gained by using the leveling
procedure under Leveling.
Leveling
CAUTION
To protect property and refrigerator from damage,
observe the following:
IMPORTANT: If refrigerator is to be installed into a
recess where the top of the refrigerator is completely
covered, use dimensions from floor to top of hinge cap
to verify proper clearance.
• Protect vinyl or other flooring with cardboard, rugs,
or other protective material.
Transporting Your Refrigerator
• Do not use power tools when performing leveling
procedure.
• NEVER transport refrigerator on its side. If an
upright position is not possible, lay refrigerator on its
back. Allow refrigerator to sit upright for
approximately 30 minutes before plugging it in to
assure oil returns to the compressor. Plugging the
refrigerator in immediately may cause damage to
internal parts.
To enhance the appearance and maintain performance,
the refrigerator should be level. (side to side)
Note
• Complete any required door reversal, panel
installation and/or a water supply connection,
before leveling.
• Use an appliance dolly when moving refrigerator.
ALWAYS truck refrigerator from its side or
back–NEVER from its front.
• Protect outside finish of refrigerator during transport
by wrapping cabinet in blankets or inserting padding
between the refrigerator and dolly.
Materials Needed
3
• ⁄8" hex head driver
• Carpenter’s level
• Secure refrigerator to dolly firmly with straps or
bungee cords. Thread straps through handles when
possible. Do not overtighten. Overtightening
restraints may dent or damage outside finish.
1. Remove toe grille.
• Grasp firmly and pull outward
to unclip.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
2. Remove bottom bracket cover(s).
Note
• Place the eraser end of a pencil or similar blunt
tool in the cover notch.
• For proper reinstallation, ensure the “top” marking
on the interior of the toe grille is oriented correctly.
• Align the toe grille mounting clips with the lower
cabinet slots.
Notch
Location
• Snap bottom portion into place first. Press
down on top of grille until top portion snaps into
place.
• Use slight pressure to pry the
cover loose.
For pullout drawer only:
Roller Adjustment Screw
• Continue to maintain
downward pressure to the
notched side of the cover while
swinging it off.
1. Turn both stabilizing
legs clockwise until
firmly against floor.
Turn roller adjustment
Stabilizing
Leg
screws 2 to 3 times
counterclockwise so that the full weight of
refrigerator rests on stabilizing legs.
3. Using hex head driver, turn the front adjustment
screws (A) on each side to raise or lower the front
of the refrigerator.
2. Replace toe grille and bracket cover(s). See
A B
B A
markings on inside of toe grille to insure proper
placement.
Handles
C
C
If not installed, the handle is located in the interior of
the fresh food section or attached to the back of your
refrigerator.
Note
• Some models only have adjustment screws “A.”
Remove and discard handle packaging and tape.
4. Select models also have rear adjustment screws
(B). Using the hex head driver, turn each of these
adjustment screws (B) to raise or lower the rear of
the refrigerator.
Handle design varies from refrigerator to refrigerator.
Please reference the appropriate instructions for your
model below.
Fresh Food Handles
Front Mount Handle - Style 1
Materials Needed
5. Using the carpenter’s level, make sure front of
refrigerator is 6 mm or half bubble higher than
back of refrigerator and that the refrigerator is level
from side to side.
• Phillips screwdriver
• ⁄16" hex head driver
6. Turn stabilizing legs (C) clockwise until firmly
against floor.
5
To Install:
7. Freezer drawer models only: Turn adjustment
screws (A) counterclockwise to allow the full
weight of the refrigerator to rest on the stabilizing
legs.
1. Remove 0.6 cm hex head screws
from door face with hex head driver,
and Phillips screw from top of door.
8. Replace bracket cover(s).
• If reversing door, remove door
plugs from opposite side of door
and insert in screw holes.
• Position cover into the outer edge of the hinge.
• Swing the cover toward the cabinet and snap it
into place.
2. Align handle holes with screw holes on
door face and secure with two door face
screws from step 1.
9. Replace the toe grille.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3. Locate handle trim in literature pack and
install over top and bottom of handle, as
illustrated.
Freezer Handles
Partial-Width Handle
Materials Needed
• Secure top handle trim with remaining
screw removed in step 1.
• Phillips screwdriver
To Install:
• Snap bottom trim over bottom portion
of handle.
1. Install handle by fastening with
screws removed from edge of door.
To Remove:
• If reversing freezer door, remove
door plugs from top edge of door
and insert into screw holes.
1. Remove top handle trim by removing top
handle screw.
• Retain trim and screw for later
replacement.
To Remove:
1. Remove handle screws with Phillips
screwdriver and retain screws for
later use.
2. Pry bottom handle trim from handle with
screwdriver flat blade wrapped in
masking tape.
• Retain trim for later replacement.
3. Remove two hex head screws.
Front Mount Handle - style 2
Materials Needed
• Retain screws for later replacement.
• Gloves to protect hands
• Phillips screwdriver
• Plastic door removal card (or 0.1 cm thick plastic
card), retain the card
Side Mount Handle
Materials Needed
Attach Extensions to
Handle: (select models)
• Phillips screwdriver
To Install:
1. Align handle and
extension as shown.
1. Remove screws from the side of the door.
2. Place extension in handle opening.
2. Align the side mount handle with the predrilled
holes in the door panel.
3. Apply slight pressure to both sides of the
extension piece.
3. Insert the screws in the sequence as
shown.
4. Slide extension until it stops on
inside edge of handle.
Upper
Handle
To Install:
2
1. The handles are to be oriented
as shown.
4
1
Lower
3
2. Align front mount door handle
clip with the door tabs.
Handle
4. Ensure the door handle is snug to the
door panel.
3. Ensure the handle clips are
Handle
Clip
To Remove:
positioned slightly above the
door tabs.
Reverse installation procedure.
Door
Tab
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Front Mount Freezer Handle
Materials Needed
4. Rotate the handle so that the
handle is flat against the door.
• Gloves to protect hands.
• Phillips screwdriver.
• Plastic handle removal card (or 0.1 cm thick plastic
card). Retain the card.
5. Push the handle down against the
upper door tab just enough to
allow it to hang unsupported.
Notes
• There is a slight curve to
this style of freezer
handle.
• For proper installation, be
sure handle is oriented as shown.
6. Align bottom of handle with lower
door tab. Press upper handle end to
door surface and firmly grasp lower
end of handle. Gently slide handle
upward until bottom of handle
To Install:
1. Align door handle clips slightly to the left of the
tabs attached to the freezer door.
2. Rotate the handle so the left base is flat against
the door.
settles on door surface, then
reverse direction, sliding downward
to almost engaging tab with clip.
Door
Tab
Handle
Clip
7. Grasp the handle firmly and slide
down until it clicks. The audible
click indicates fastening clips are
securely interlocked.
Handle
Base
To Remove:
1. Flex the handle away from the door
panel. Simultaneously place door
handle removal card underneath
the base of the lower handle. Insert
the card to the line or until it stops.
3. Push the left handle
base against the left
door tab and slightly
to the right, just
enough to allow it to
hang unsupported.
4. While firmly supporting the left handle base against
the door, align the right base of the handle with the
right tabs that are attached to the door.
2. Grasp the lower part of the handle
firmly and lift to remove.
5. Now, while firmly holding the handle at the left and
right bases, gently slide the handle towards the
right until the right base settles in. The handle
should now be flat against the face of the freezer
door at both the left and right bases.
6. With hands still firmly keeping the handle flat
against the freezer door, you may have to reverse
directions momentarily to assure clip/tab
engagement. Then firmly slide the handle to the
right until it clicks. The audible "click" indicates
that the fastening clips are securely interlocked.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
When the left door is opened, the hinged seal
automatically folds inward so that it is out of the way.
To Remove:
1. At the right end, flex the handle base away from
the surface of the freezer drawer. Simultaneously
slide the door handle removal card that came with
your refrigerator under the right side base of the
handle. Slide the card to the line indication or until
it stops.
WARNING
To avoid electrical shock which can cause severe
personal injury or death, DO NOT attempt to
remove the hinged seal from the fresh food
section.
2. With both hands, firmly grasp the handle towards
the right base.
CAUTION
To avoid possible product damage, ALWAYS verify
that the hinged seal is folded against the edge of
the door prior to closing.
3. Slide towards the left, lift and remove from the
surface.
Hinged
Seal
Handle Removal
Euro Handles
This handle style is installed at the factory
Materials Needed:
3
• ⁄32” allen wrench
To Remove:
• Remove set screw from
handle mounting post using
3
⁄
32” allen wrench.
• Repeat the procedure on all
posts to remove the handle.
How to Connect the Water
To Replace:
Supply (select models)
• Align handle with the
mounting posts.
WARNING
Contact a qualified engineer to perform this task.
• Fully tighten all set screws to secure handle
in place.
Ice Maker Operation
• To turn ice maker On push arm down from locked
position.
Opening and Closing Your
Fresh Food Doors (select models)
Your new refrigerator is uniquely designed with two
fresh food doors. Either door can be opened or closed
independently of one another.
There is a vertically-hinged section on the left fresh
food door. When the left door is closed, the hinged
section automatically forms a seal between the two
doors when both doors are closed.
• Lift arm up and lock into position to turn ice maker
Download from Www.Somanuals.com. All MOanfuf.als Search And Download.
7
Temperature Controls
Adjusting the Controls
Touch Temperature Controls
(select models, style varies by model)
• 24 hours after adding food, you may decide that one
or both compartments should be colder or warmer. If
so, adjust the control(s) as indicated in the
Temperature Control Guide table below. See page 13
for instructions on checking compartment
temperature.
The controls are located at the top front of the
refrigerator compartment.
Control
• Except when starting the refrigerator, do not change
either control more than one number at a time.
Initial Control Settings
• Allow 24 hours for temperatures to stabilize.
After plugging the refrigerator in, set the controls.
Temperature Control Guide
• Pressing the
or
pads adjusts the controls
Refrigerator too warm Set the refrigerator control
to the desired setting.
to next higher number by
pressing the
• The temperature control range for both
compartments is 1 through 7 (coldest).
pad.
Refrigerator too cold Set the refrigerator control
• Set the freezer control on 4.
to next lower number by
pressing the
pad.
• Set the refrigerator control on 4.
Freezer too warm
Freezer too cold
Turn control OFF
Set the freezer control to
next higher number by
• Let the refrigerator run at least 8 to 12 hours before
adding food.
pressing the
pad.
Warm Cabinet Surfaces
Set the freezer control to
next lower number by
At times, the front of the refrigerator cabinet may be
warm to the touch. This is a normal occurrence that
helps prevent moisture from condensing on the
cabinet. This condition will be more noticeable when
you first start the refrigerator, during hot weather and
after excessive or lengthy door openings.
pressing the
Press the refrigerator or
freezer pad until a dash
(—) appears in the display.
pad.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Fresh Food Features
To Remove:
Shelves
Completely unload the shelf and pull the shelf forward.
When the shelf stops, press up on the tabs located
underneath its outside edges, then continue pulling
forward, clear of the frame.
CAUTION
To avoid personal injury or property damage,
observe the following:
• Never attempt to adjust a shelf that is loaded with
food (except in the case of the Elevator™ shelf).
To Install:
Align the shelf to the frame and push it all the way
back. (There is no need to depress the tabs for
reinstallation).
• Confirm shelf is secure before placing items on
shelf.
• Handle tempered glass shelves carefully. Shelves
may break suddenly if nicked, scratched, or
exposed to sudden temperature change.
In ordinary use, the Elevator™ shelf frame assembly
does not require removal. Though unlikely, and not
recommended, the correct removal procedure is as
follows:
Your refrigerator has either Spill-Catcher™ or non-
sealed Shelves. The Spill-Catcher™ shelves have a
spill retainer edge which allows for easier clean up and
some are equipped with the Easy Glide slide out
feature. To slide out (select models), grasp the front of
the shelf and pull forward. Push in the shelf to return
to the original position.
To Remove:
• Unload the shelf completely.
• Remove glass shelf by pulling forward. When shelf
stops lift up and continue pulling forward.
• Manually move the two rear latches toward the shelf
center.
To Remove a Shelf:
• While supporting the entire shelf and frame from
underneath, lift slightly and rotate the assembly
approximately 30° to allow the rear mechanism to
clear the vertical rear side rails.
• Slightly tilt up the
front and lift up the
rear of the shelf, then
pull the shelf straight
out.
• The entire assembly can then be moved forward and
clear of the refrigerator compartment.
To Lock the Shelf Into Another Position:
To Install:
• Tilt up the front edge of the shelf.
• Reverse the removal procedure. Be sure the shelf is
in a level position.
• Insert the hooks into the desired frame openings and
let the shelf settle into place.
• When the sliding shelf is pushed to the rear, it will
reposition the rear latches to their correct operating
position.
• Be sure the shelf is securely locked at the rear.
Elevator™ Shelf (select models)
The fresh food compartment is equipped with an
Elevator™ shelf.
This shelf can be adjusted up or down without having
to be unloaded of its contents. To adjust an Elevator™
shelf, pull out the knob on the crank handle. Rotate the
crank clockwise to raise the height of the shelf, and
counterclockwise to lower the height of the shelf.
Note
• Do not raise the shelf to the very top of the
vertical rails, as the shelf may become jammed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Fresh Food Features
The Crisper Top serves as the lower fresh food shelf.
To Remove the Crisper Top:
Storage Drawers
Snack Drawer (select models)
• Remove crisper drawers as indicated on page 11.
The Snack Drawer can be used for
storage of miscellaneous items or
extra produce.
• Place hand under the frame to push up the glass. Lift
glass out.
• Lift frame from refrigerator liner rails.
To Install:
To Remove:
• Pull drawer out to full extension. Tilt up front
of drawer and pull straight out.
• Repeat above instructions in reverse order.
To Install:
Door Storage
• Insert drawer into frame rails and push back into
place.
Dairy Compartment
The Dairy Compartment provides
convenient door storage for
Beverage Chiller™
(select models)
spreadable items such as butter
and margarine. This compartment can be moved to
different locations to accommodate storage needs. To
use the dairy compartment, raise the cover.
The Beverage Chiller™ keeps
beverages and other items cooler
than the rest of the fresh food
To Remove:
section. A cold air inlet allows air from the freezer
section to pass into the beverage chiller.
The Beverage Chiller™ control is located
on the left wall of the fresh food
compartment. The control adjusts the
amount of cold air allowed in to the
beverage chiller. For a cooler temperature
in the Beverage Chiller™ slide the control
down.
• Raise the cover, pull upward and tilt out.
To Install:
• Reverse above procedure.
Door Buckets
Door Buckets can be moved to meet
storage needs.
To Remove:
To Remove:
• First remove the pick off
shelf to the left of the
Beverage Chiller™.
• Slide bucket up and pull straight
out.
To Install:
• Firmly hold each side of
beverage chiller, lift up
and away from door liner.
• Slide bucket in and down until firmly seated in the
door liner.
To Install:
• Reverse above procedure.
Full-width Door Shelf
Full-width Door Shelf removes for easy cleaning.
To Remove:
• Slide shelf up and pull
straight out.
To Install:
• Reverse above procedure.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Fresh Food Features
Humidity-Controlled Crisper Drawers
Notes
The Crisper Drawers provide a higher humidity
environment for fresh fruit and vegetable storage.
• Cold air directed to the drawer can decrease
refrigerator temperature. Refrigerator control may
need to be adjusted.
Controls
The Crisper Controls regulate the amount of humidity
in the crisper drawer. Slide the control towards the
fruit setting when storing produce with outer skins.
Slide the control towards the vegetable setting when
storing leafy produce.
• Do not place leafy vegetables in the drawer.
Colder temperatures could damage leafy produce.
To Remove:
• Lift lid (select models). Pull drawer out to full
extension. Tilt up front of drawer and pull straight
out.
To Install:
• Push metal glide rails to the back of the refrigerator
(select models). Place drawer onto rails and slide
drawer back until it falls into place.
To Remove:
• Pull drawer out to full extension. Tilt up front of
drawer and pull straight out.
Some models feature a divider to organize the drawer
into sections.
To Install:
• Insert drawer into frame rails and push back into
place.
To Remove:
• Pull drawer completely out and raise the front of the
divider to unhook it from the rear wall of the drawer
and lift it out.
Note
• For best results, keep the crisper drawers tightly
closed.
To Install:
• Hook back of divider over rear wall of the drawer and
lower into place.
Temperature-Controlled Drawer
(select models)
Accessories (select models)
Wine Trivet/ Can Rack
The deli drawer is a full-width drawer with adjustable
temperature control. This drawer can be used for large
party trays, deli items, beverages or miscellaneous
items.
The Wine Trivet/ Can Rack
accessory fits in the deli drawer or
on a shelf.
There is a temperature control which adjusts the
amount of cold air allowed into the drawer. The
control is located on the right side of the drawer.
Depending on your model, it is either on the front of
the drawer or under the lid.
Bottles or cans can be laid
crosswise, or a single bottle may be
laid in the center depression.
Egg Cradle
Set the control to cheese or to provide a normal
The Egg Cradle (style may vary/select models) holds a
“dozen-plus” eggs. It can be removed to carry to work
area or to be washed.
refrigerator temperature. Set the drawer on the
meats or setting when a temperature colder than
the main refrigerator compartment is desired. Use the
coldest setting when storing meats.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Freezer Features
Models with pullout freezer drawer:
Shelves and Baskets
Models with swing freezer door:
DANGER
To prevent accidental child entrapment or
suffocation risk, do not remove the divider in the top
freezer basket.
Freezer Shelf (select models)
Select models have a shelf divider.
To Remove:
Upper Wire Basket
• Pull shelf out to full
extension. Tilt up front of
shelf and pull straight out.
To Remove:
• Pull upper basket out to full extension and lift out to
remove.
To Install:
To Install:
• Insert shelf into freezer liner rails and push to back
of compartment.
• Slide upper basket into freezer. Make sure that rear
of basket hooks behind rail catch.
Wire Basket (select models)
To Remove:
• Pull basket out to full
extension. Tilt up front of
basket and pull straight out.
Accessories (select models)
Ice Cube Tray
To Install:
• Insert basket into freezer liner rails and push back
into place.
The Ice Cube Tray provides an area
to freeze cubes for manual
dispensing of ice.
Freezer Door Shelf (select models)
The Freezer Door Shelf provides
convenient storage for frozen food
items in freezer door.
To release ice cubes from tray, hold tray upside down
over a storage container and twist both ends of tray
until cubes release.
To Remove:
The Ice Service Rack (select models) holds the ice
cube tray.
• Lift shelf from side liner tabs and pull
out.
To Install:
To Install:
• Slide L-shaped groove of shelf
down over back wall screw.
• Fit ends of shelf on liner tabs and slide down.
1
Push rack back until screw is
2
stopped in L-shaped groove
(1). Slide front portion of shelf
over front wall screw (2).
To Remove:
• Perform above steps in reverse order.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Food Storage Tips
Fresh Food Storage
Frozen Food Storage
• The fresh food compartment of a refrigerator should
be kept between 1°- 4° C with an optimum
• The freezer compartment of a refrigerator should be
kept at approximately -18° C. To check the
temperature, place an appliance thermometer
between the frozen packages and check after 24
hours. If the temperature is above -18° C, adjust the
control as described on page 8.
temperature of 3° C. To check the temperature, place
an appliance thermometer in a glass of water and
place in the center of the refrigerator. Check after 24
hours. If the temperature is above 4° C adjust the
controls as explained on page 8.
• A freezer operates more efficiently when it is at least
two-thirds full.
• Avoid overcrowding the refrigerator shelves. This
reduces the circulation of air around the food and
results in uneven cooling.
Packaging Foods for Freezing
• To minimize dehydration and quality deterioration use
aluminum foil, freezer wrap, freezer bags or airtight
containers. Force as much air out of the packages as
possible and be sure they are tightly sealed. Trapped
air can cause the food to dry out, change color and
develop an off-flavor (freezer burn).
Fruits and Vegetables
• Storage in the crisper drawers traps humidity to help
preserve the fruit and vegetable quality for longer
time periods (see page 11).
• Sort fruits and vegetables before storage and use
bruised or soft items first. Discard those showing
signs of decay.
• Overwrap fresh meats and poultry with suitable
freezer wrap prior to freezing.
• Always wrap odorous foods such as onions and
cabbage so the odor does not transfer to other foods.
• Do not refreeze meat that has completely thawed.
Loading the Freezer
• While vegetables need a certain amount of humidity
to remain fresh, too much humidity can shorten
storage times (especially leafy vegetables). Drain
vegetables well before storing.
• Avoid adding too much warm food to the freezer at
one time. This overloads the freezer, slows the rate of
freezing and can raise the temperature of frozen
foods.
• Wait to wash fresh produce until right before use.
• Leave space between the packages so cold air can
circulate freely, allowing food to freeze as quickly as
possible.
Meat and Cheese
• Raw meat and poultry should be wrapped securely
so leakage and contamination of other foods or
surfaces does not occur.
• Avoid storing hard-to-freeze foods such as ice cream
and orange juice on the freezer door shelves. These
foods are best stored in the freezer interior where the
temperature varies less with door openings.
• Occasionally mold will develop on the surface of
hard cheeses (Swiss, Cheddar, Parmesan). Cut off at
least an inch around and below the moldy area. Keep
your knife or instrument out of the mold itself. Do not
try to save individual cheese slices, soft cheese,
cottage cheese, cream, sour cream or yogurt when
mold appears.
Dairy Food
• Most dairy foods such as milk, yogurt, sour cream
and cottage cheese have freshness dates on their
cartons for appropriate length of storage. Store these
foods in the original carton and refrigerate
immediately after purchasing and after each use.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
WARNING
CAUTION
To avoid personal injury or property damage,
observe the following:
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before cleaning. After cleaning, connect
power.
• Read and follow manufacturer’s directions for all
cleaning products.
• Do not place buckets, shelves or accessories in
dishwasher. Cracking or warping of accessories
may result.
Refrigerator Cleaning Chart
PART
DO NOT USE
DO
Textured Doors
and Exterior
Abrasive or harsh cleaners
Ammonia
Use 4 tablespoons of baking soda dissolved in
1 liter warm soapy water.
Chlorine bleach
Concentrated detergents
or solvents
Rinse surfaces with clean warm water and dry
immediately to avoid water spots.
Cabinet Interior
Metal or plastic-textured
scouring pads
Stainless Steel Doors and
Exterior (select models)
IMPORTANT:
Damage to stainless steel
finish due to improper use
of cleaning products or
non-recommended products
is not covered under this
product’s warranty.
Abrasive or harsh cleaners
Ammonia
Chlorine bleach
Concentrated detergents
or solvents
Metal or plastic-textured
scouring pads
Use warm, soapy water and a soft, clean cloth
or sponge.
Rinse surfaces with clean warm water and dry
immediately to avoid water spots.
To polish and help prevent finger prints, follow
with Stainless Steel Magic Spray (part no.
20000008*).
Vinegar-based products
Citrus-based cleaners
Door Gaskets
Abrasive or harsh cleaners
Metal or plastic-textured
scouring pads
Use warm, soapy water and a soft, clean cloth
or sponge.
Condenser Coil
Use a vacuum cleaner hose nozzle.
Remove base grille to access.
Condenser Fan Outlet Grille
See back of refrigerator.
Use a vacuum cleaner hose nozzle with brush
attachment.
Accessories
Shelves, buckets,
drawers, etc.
A dishwasher
Follow removal and installation instructions
from appropriate feature section.
Allow accessories to adjust to room
temperature.
Dilute mild detergent and use a soft clean cloth
or sponge for cleaning.
Use a plastic bristle brush to get into crevices.
Rinse surfaces with clean warm water.
Dry glass and clear items immediately to avoid
spots.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Removing Odors From
Energy Saving Tips
• Avoid overcrowding refrigerator shelves. This reduces
air circulation around food and causes refrigerator to
run longer.
Refrigerator
WARNING
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before cleaning. After cleaning,
reconnect power.
• Avoid adding too much warm food to refrigerator at
one time. This overloads compartments and slows
rate of cooling.
• Do not use aluminum foil, wax paper, or paper
toweling as shelf liners. This decreases air flow and
causes refrigerator to run less efficiently.
1. Remove all food and turn the refrigerator OFF.
2. Disconnect power to the refrigerator.
• A freezer that is two-thirds full runs most efficiently.
3. Clean the walls, floor, ceiling of cabinet interior,
drawers, shelves and gaskets according to the
instructions on page 14.
• Locate refrigerator in coolest part of room. Avoid
areas of direct sunlight, or near heating ducts,
registers or other heat producing appliances. If this is
not possible, isolate exterior by using a section of
cabinet.
4. Dilute mild detergent and brush solution into
crevices using a plastic bristle brush. Let stand for
five minutes. Rinse surfaces with warm water. Dry
surfaces with a soft, clean cloth.
• Clean door gaskets every three months according to
cleaning instructions. This will assure that door seals
properly and refrigerator runs efficiently.
5. Wash and dry all bottles, containers and jars.
Discard spoiled or expired items.
• Take time to organize items in refrigerator to reduce
time that door is open.
6. Wrap or store odor-causing foods in tightly sealed
containers to prevent recurring odors.
• Be sure your doors are closing securely by leveling
refrigerator as instructed in your installation
instructions.
7. Reconnect power to refrigerator and return food to
refrigerator.
• Clean condenser coils as indicated in the cleaning
instructions every three months. This will increase
energy efficiency and cooling performance.
8. Allow the refrigerator to cool.
9. After 24 hours, check if odor has been eliminated.
If odor is still present:
1. Remove drawers and place on top shelf of
refrigerator.
2. Pack refrigerator and freezer sections – including
doors – with crumpled sheets of black and white
newspaper.
3. Place charcoal briquettes randomly on crumpled
newspaper in both freezer and refrigerator
compartments.
4. Close doors and let stand 24 to 48 hours.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Freezer (style of light shield varies)
Replacing Light Bulbs
1. Reach behind the light
cover.
WARNING
To avoid electrical shock which can cause severe
personal injury or death, disconnect power to
refrigerator before replacing light bulb. After
replacing light bulb, reconnect power.
2. With firm pressure, press
forward on the notches at
the back of the cover and
pull down. The cover will
open from the back.
CAUTION
3. Remove the cover.
4. Remove light bulb.
To avoid personal injury or property damage,
observe the following:
5. Replace bulb with
appliance bulb no
• Allow light bulb to cool.
• Wear gloves when replacing light bulb.
greater than 40 watts.
6. Insert front tabs of light
cover into slots in freezer
liner and snap rear
portion over light
Fresh Food Section
(style of light shield varies)
1. Slide clear light shield
toward back of
assembly until rear tab
engages.
compartment to release
from light assembly.
2. Remove light bulbs.
3. Replace with appliance
bulbs no greater than 40 watts.
4. Replace light shield by aligning edge of shield with
control housing. Slide shield toward front of
refrigerator until it locks into place on ‘T’ shape
locking tab. Do not force shield beyond locking
point. Doing so may damage light shield.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Upon your return:
Preparing for Vacation
After a short vacation or absence:
For models with automatic ice makers:
• Reconnect the water supply and turn on supply valve.
CAUTION
If your refrigerator has a dispenser and there is any
possibility that the temperature can drop below
freezing where the refrigerator is located, the water
supply system (including the water tank and the
water valve) must be drained by a qualified servicer.
• Monitor water connection for 24 hours and correct
leaks if necessary.
• Restart the ice maker.
For short vacations or absences (three months or
less):
• Discard at least the first three ice harvests.
After a long vacation or absence:
1. Remove all perishables.
• If your refrigerator has an automatic ice maker,
reconnect the water supply and turn on supply valve.
2. If no one will be checking in on the refrigerator
during your absence, remove all frozen items also.
• Plug the refrigerator back in and reset controls (see
page 8).
3. If your refrigerator has an automatic ice maker:
• Shut off the water supply to the ice maker at
least one day ahead of time.
• Monitor water connection for 24 hours and correct
leaks, if necessary.
• After the last load of ice drops, raise the wire
shut off arm to the OFF position.
• Restart the ice maker.
• Discard ice produced within the first 12 hours (at
least the first three harvests).
• Empty the ice bin.
4. If the room temperature will drop below 13° C,
follow the instructions for longer absences.
Preparing to move:
• Follow the above instructions for long
vacations/absences, through step 6.
For long vacations, absences (more than three
months) OR if the room temperature will drop
below 13° C:
• Secure all loose items such as shelves and drawers
by taping them securely in place to prevent damage.
1. Remove food.
2. If your refrigerator has an automatic ice maker:
• Tape the doors shut.
• Shut off the water supply to the ice maker at
least one day ahead of time.
• Use an appliance dolly when moving the refrigerator.
Always truck the refrigerator from its side or back-
never from its front.
• After the last load of ice drops, raise the wire
shut off arm to the OFF position.
• Be sure the refrigerator stays in an upright position
during moving.
• Empty the ice bin.
3. Turn the freezer control to (OFF) with dial controls
or (—) with touch controls (see page 8).
4. Unplug the refrigerator.
5. Thoroughly clean the interior of both compartments
with a baking soda solution and a clean soft cloth
(four tablespoons of baking soda in one quart of
warm water).
6. Dry thoroughly.
7. Leave the doors open to prevent the formation of
mold and mildew.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Sounds
Improvements in refrigeration design may produce sounds in your new refrigerator that are different or were not
present in an older model. These improvements were made to create a refrigerator that is better at preserving food,
is more energy efficient, and is quieter overall. Because new refrigerators run quieter, sounds may be detected that
were present in older refrigerators, but were masked by higher sound levels. Many of these sounds are normal.
Please note that the surfaces adjacent to a refrigerator, such as hard walls, floors and cabinetry may make these
sounds seem even louder. The following are some of the normal sounds that may be noticed in a new refrigerator.
SOUND
Clicking
POSSIBLE CAUSE
SOLUTION
• Normal operation
• Freezer control (A) clicks when starting or
stopping compressor.
• Motorized device (B) sounds like an electric
clock and snaps in and out.
• Normal operation
• Normal operation
• Normal operation
• Normal operation
• Normal operation
Air rushing or
whirring
• Freezer fan (C) and condenser fan (D) make
this noise while operating.
Gurgling or
boiling sound
• Evaporator (E) and heat exchanger (F)
refrigerant makes this noise when flowing.
Thumping
• Ice cubes from ice maker (select models) drop
into ice bucket (G).
Vibrating noise
• Compressor (H) makes a pulsating sound
while running.
• Refrigerator is not level.
• See page 3 for details on how to level
your refrigerator.
Buzzing
• Ice maker water valve (I) hookup (select
models) buzzes when ice maker fills with
water.
• Normal operation
Humming
• Ice maker (J) is in the ‘on’ position without
water connection.
• Stop sound by raising ice maker arm
to OFF position.
• Compressor (H) can make a high-pitched hum • Normal operation
while operating.
Hissing or
popping
• Defrost heater (K) hisses, sizzles or pops when • Normal operation
operational.
B
B
A
C
E
I
J
G
H
K
D
F
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
Freezer control and
lights are on, but
compressor is not
operating
Refrigerator is in defrost mode.
Normal operation.
Wait 40 minutes to see if refrigerator restarts.
Crisper drawer
temperature is too
warm
Control settings are too low.
See page 8 to adjust controls.
Refrigerator does
not operate
Refrigerator is not plugged in.
Control is not on.
Plug in refrigerator.
See page 8 to adjust your controls.
Fuse is blown, or circuit breaker needs
to be reset.
Replace any blown fuses.
Check circuit breaker and reset, if necessary.
Power outage has occurred.
Refrigerator is malfunctioning.
Call local power company listing to report outage.
Refrigerator still
won’t operate
Unplug refrigerator and transfer food to another
refrigerator. If another refrigerator is not available,
place dry ice in freezer section to preserve food.
Warranty does not cover food loss.
Contact service for assistance.
Food temperature
is too cold
Condenser coils are dirty.
Clean according to the chart on page 14.
See page 8 to adjust your controls.
Refrigerator or freezer controls are set
too high.
Food temperature
is too warm
Door is not closing properly.
Refrigerator is not level. See page 3 for details on how
to level your refrigerator.
Check gaskets for proper seal. Clean, if necessary,
according to the chart on page 14.
Check for internal obstructions that are keeping door
from closing properly (i.e. improperly closed drawers,
ice buckets, oversized or improperly stored
containers, etc.)
Controls need to be adjusted.
Condenser coils are dirty.
Rear air grille is blocked.
See page 8 to adjust your controls.
Clean according to the chart on page 14.
Check the positioning of food items in refrigerator to
make sure grille is not blocked. Rear air grilles are
located under crisper drawers.
Door has been opened frequently, or has
been opened for long periods of time.
Reduce time door is open.
Organize food items efficiently to assure door is open
for as short a time as possible.
Food has recently been added.
Allow time for recently added food to reach
refrigerator or freezer temperature.
Refrigerator has
an odor
Compartment is dirty or has odor-
causing food.
Clean according to instructions on page 14.
Water droplets
form on outside
Check gaskets for proper seal.
Humidity levels are high.
Clean according to the chart on page 14.
Normal during times of high humidity.
See page 8 to adjust your controls.
of refrigerator
Controls require adjustment.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
Water droplets form Humidity levels are high or door has
on inside of
refrigerator
See page 8 to adjust your controls.
Reduce time door is open.
Organize food items efficiently to assure door is open
for as short a time as possible.
been been opened frequently.
Check gaskets for proper seal.
Normal operation.
Clean, if necessary, according to the chart on page 14.
Refrigerator or ice
maker makes
unfamiliar sounds
or seems too loud
See page 18.
Crisper drawers
do not close freely
Contents of drawer, or positioning of
items in the surrounding compartment
could be obstructing drawer.
Reposition food items and containers to avoid
interference with the drawers.
Drawer is not in proper position.
Refrigerator is not level.
See page 11 for proper drawer placement.
See page 3 for details on how to level your
refrigerator.
Drawer channels are dirty or need
treatment.
Clean drawer channels with warm, soapy water.
Rinse and dry thoroughly.
Apply a thin layer of petroleum jelly to drawer
channels.
Refrigerator runs
too frequently
Doors have been opened frequently or
for long periods of time.
Reduce time door is open.
Organize food items efficiently to assure door is open
for as short a time as possible.
Allow interior environment to adjust for period the
door has been opened.
Humidity or heat in surrounding area is
high.
Normal operation.
Food has recently been added.
Allow time for recently added food to reach
refrigerator or freezer temperature.
Refrigerator is exposed to heat by
environment or by appliances nearby.
Evaluate your refrigerator’s environment. Refrigerator
may need to be moved to run more efficiently.
Condenser coils are dirty.
Controls need to be adjusted.
Door is not closing properly.
Clean, if necessary, according to the chart on page 14.
See page 8 to adjust your controls.
Refrigerator is not level. See page 3 for details on how
to level your refrigerator.
Check gaskets for proper seal.
Clean, if necessary, according to the chart on page 14.
Check for internal obstructions that are keeping door
from closing properly (i.e. improperly closed drawers,
ice buckets, oversized or improperly stored
containers, etc.)
Normal Operation
See Operating Sounds on page 18.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Ice
PROBLEM
POSSIBLE CAUSES
WHAT TO DO
Refrigerator is
leaking water
Supply tubing was used to complete
water connection.
The manufacturer recommends using copper tubing
for installation. Plastic is less durable and can cause
leakage. The manufacturer is not responsible for
property damage due to improper installation or
water connection.
Improper water valve was installed.
Check water connection procedure. Self-piercing and
0.5 cm saddle valves cause low water pressure and
may clog the line over time. The manufacturer is not
responsible for property damage due to improper
installation or water connection.
Water pressure is low.
Water pressure must be between 137 to 689 kpa to
function properly.
Ice forms in inlet
tube to ice maker
Adjust freezer control (see page 8). Freezer is
recommended to be approximately -18° C.
Freezer temperature is too high.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
|