ASSEMBLY, CARE & USE MANUAL
WARNING & SAFETY INFORMATION
ELECTRIC PATIO GRILL
MODELS 20150112, 20150213, 20150513, 20150613, 20150713
THIS PRODUCT IS FOR OUTDOOR USE ONLY
Approximate assembly time : 60 minutes
Tool needed for assembly: Phillips Head Screwdriver
WARNING
WARNING
This manual contains important
information necessary for the proper
and safe use of this unit.
Use only outdoors where it is
well ventilated.
Read and follow all warnings
and instructions before using
grill and during use.
Fuel, such as charcoal briquettes, wood or heat
pellets, are not to be used in the unit.
Keep this manual for future reference.
Failure to follow these warnings and instructions properly could result in personal injury or death.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL WARNINGS AND SAFETY INFORMATION
• Be careful when removing food from electric grill. All surfaces are HOT and may cause burns.
Use protective gloves or long, sturdy cooking tools.
• Drip tray is only for the bottom of electric grill. Do not put drip tray on cooking grate this may
damage electric grill.
• To disconnect, turn control panel “OFF” then remove plug from outlet.
• Unplug from outlet when not in use and before cleaning. Allow unit to cool completely before
adding/removing grate, or drip tray.
• Dispose of cold ashes by placing them in aluminum foil, soaking with water and discarding in a
non-combustible container.
• Do not store electric grill with HOT ashes inside unit. Store only when all surfaces are cold.
• Accessory attachments not supplied by Masterbuilt Manufacturing, Inc. are not recommended
and may cause injury.
• The use of accessory attachments not recommended by the appliance manufacturer may cause
injuries.
• Never use electric grill for anything other than its intended purpose. This unit is not for
commercial use.
• Always use electric grill in accordance with all applicable local, state and federal fire codes.
• Longer detachable power-supply cords or extension cords are available and may be used if care
is exercised in their use.
• If a longer detachable power-supply cord or extension cord is used: 1. The marked electrical
rating of the cord set or extension cord should be at least as great as the electrical rating of the
appliance; and 2. The cord should be arranged so that it will not drape over the counter top or
tabletop where it can be pulled by children or tripped over intentionally.
• The extension cord must be a grounding -type 3-wire cord.
• Outdoor extension cords must be used with outdoor use products and are marked with suffix
“W” and with the statement “Suitable for Use with Outdoor Appliances.
• CAUTION - To reduce the risk of electric shock, keep extension cord connection dry and off the
ground.
• Do not clean this product with a water sprayer or the like.
• Keep hands, hair and face away from the element. Be careful of loose hair and clothing
during operation, they could catch fire.
• Never use glassware, plastic or ceramic cookware on this grill.
• Preheating grill is not necessary. If preheating is desired, open lid with caution.
• Minimum distance from side and back of appliance to walls or railing is 24 inches.
• Do not use unit near heat sensitive or combustible structures such as vinyl or wood siding.
WARNINGS & IMPORTANT SAFEGUARDS CONTINUED ON PAGE 3
2
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL WARNINGS AND SAFETY INFORMATION
• Fatty foods (hamburgers,etc.) can have excess grease and cause flare ups. When cooking fatty
foods use a low setting with lid open.
• Clean internal base pan before each use. This will cut down on build-up and flare-ups.
• Do not expose electric grill to rain. Do not use around water or operate on wet surfaces. This
could cause an electric shock leading to injury and death.
• Be sure drip tray is clean before each use.
SAVE THESE INSTRUCTIONS
WARNING
COMBUSTION BY-PRODUCT PRODUCED WHEN USING THIS PRODUCT CONTAINS CHEMICALS
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS,
OTHER REPRODUCTIVE HARM, OR CANCER.
THE MATERIALS USED IN THIS PRODUCT MAY CONTAIN LEAD A CHEMICAL KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS AND OTHER REPRODUCTIVE HARM.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts
Call: MASTERBUILT Customer Service at 1-800-489-1581.
STOP!
Please have Model Number and Serial Number available when calling.
These numbers are located on silver label on back of unit.
PARTS LIST
25
26
27
23
2g
3
6
4
1
28
2b
7
5
24
21
22
8
10
9
18
20
19
11
a
11
b
12
16
17
13
14f
15
14b
PART NO
QTY DESCRIPTION
PART NO
QTY DESCRIPTION
1
2g
2b
3
1
1
1
1
1
Grill Lid
14b
1
2
2
2
2
Back Panel
Hub Cap
Wheel
Foot
Temperature Gauge
15
Temperature Gauge Base
Right Side Shelf
16
17
4
Heating Element
18*
Leg
5
1
Grill Base
19*
2
Wheel Leg
6
7
1
1
1
1
1
2
2
Left Side Shelf
20
21
22
23
24
25
26
1
1
2
1
1
1
1
Cooking Grate
Warming Rack
Seat
Drip Tray
8
Drip Tray Bracket
Reflector Plate
9
Right Bottom Hinge
Left Bottom Hinge
Left Lid Hinge
Right Lid Hinge
10
11a
11b
Controller
Front right/Back left Support
Front left/Back right Support
12
13
1
2
1
Bottom Shelf
Side Panel
Front Panel
27
28
1
1
Handle
Logo Base
14f
*Legs are marked with stickers (FR-Front Right, FL-Front Left, BR-Back Right, BL-Back Left) to correspond easily with parts 11a and
4
11b during assembly Steps 3-5.
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE LIST
(B)
M6x35
(C)
34x25
(A)
M5
(D)
M4x40
Phillips Head Screw
Qty: 2
Flat Washer
Qty: 4
Thumb Screw
Qty: 2
Phillips Head Screw
Qty: 2
(G)
M6x13
Phillips Head Screw
Qty: 40
(E)
M8x55
Phillips Head Screw
Qty:2
(F)
Bakelite Spacer
Qty: 2
(H)
M4x12
Phillips Head Screw
Qty: 3
(I)
M6
(L)
M6x8
(J)
M4
(K)
M8
Flat Washer
Qty: 8
Phillips Head Screw
Qty: 4
Flat Washer
Qty: 5
Flat Washer
Qty: 2
PARTS LIST
PART NO
REPLACEMENT PART
PART NO
REPLACEMENT PART
9915110002 Lid Kit - Blue
9915110016 Rear Left Leg Kit
9915110017 Rear Right Leg Kit
9915110018 Front Panel Kit
9915110019 Back Panel Kit
9915110020 Side Panel Kit
9915110021 Bottom Shelf Kit
9915110022 Wheel Kit
9915110003 Base Kit - Blue
9915110004 Lid Handle Kit
9915110005 Hinge Kit
9915110006 Right Side Shelf Kit
9915110007 Left Side Shelf Kit
9915110008 Logo Plate Kit
9915110009 Temperature Gauge Kit
9915110010 Drip Tray Kit
9910090010 Element Kit
9015110002 Foot
9915110011 Grill Seat Kit
9015110003 Warming Rack
9015110004 Cooking Grate
9015110005 Reflector Plate
9015110001 Grill Cover
9915110012 Front Left/Back Right Leg Kit
9915110013 Front Right/Back Left Leg Kit
9915110014 Front Left Leg Kit
9915110015 Front Right Leg Kit
9015110006 Hub Cap
9007090063 Analog Control w/ Power Cord
9915110023 Lid Kit - Red
9915110024 Lid Kit - Black
9915110026 Base Kit - Black
9915110025 Base Kit - Red
9915110001 Hardware Kit
9815110001 Instruction Manual
DO NOT RETURN TO RETAILER For Assembly Assistance, Missing or Damaged Parts
Call: MASTERBUILT Customer Service at 1-800-489-1581.
STOP!
Please have Model Number and Serial Number available when calling.
These numbers are located on silver label on back of unit.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• BEFORE ASSEMBLY READ ALL INSTRUCTIONS CAREFULLY.
• ASSEMBLE UNIT ON A CLEAN, FLAT SURFACE.
• TOOL NEEDED: PHILLIPS HEAD SCREWDRIVER
• UNPACK ALL PARTS AND LAY OUT IN FRONT OF YOU. CHECK TO MAKE SURE ALL PARTS
ARE IDENTIFIED AND ACCOUNTED FOR.
*Note that the front of the grill is actually the shortest width of the bottom storage shelf (12).
LABELS
FR – Front Right,
FL – Front Left,
BL
19
BR – Back Right,
BL – Back Left
FL
19
BR
18
16
12
15
18
FR
K
17
E
18
FR
17
ALIGN
NOTCH
STEP 1
Begin assembly by positioning
bottom shelf (12) with the short
side of shelf facing you.
STEP 2
STEP 3
This will actually be the front of
the grill, making the long sides of
shelf the left and right sides.
Attach wheel (16) to leg (19, “FL”) Align notch on back of foot (17)
using washer (K) and screw (E)
as shown.
with the slot in leg (18,”FR”) and
insert into leg.
NOTE: DO NOT FULLY
TIGHTEN ANY SCREWS
UNTIL ALL SCREWS ARE IN
PLACE AND THE GRILL IS
FULLY ASSEMBLED.
Snap hubcap (15) onto wheel.
Repeat step for remaining wheel
and wheel leg (19 “BL”).
Repeat for remaining leg (18,
“BR”) and foot (17).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 4
Attach bottom shelf (12) to legs
(18) using screws (G) with the feet
facing away from right side of the
shelf as shown.
19
12
Repeat for wheel legs (19) on left
side using screws (G).
G
18
REMEMBER!
The short side of bottom
shelf (12) is the front of grill.
14f
13
STEP 5a
Locate front panel (14f) [This is the
short panel without the serial plate]
and one side panel (13) [This is
one of the longer panels].
Place panel (14f) over (13) while
aligning screw holes. Insert screw
(G) through both panels, securing
panels to front right leg (18, “FR”).
G
18
FR
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 5b
Repeat step 4a for leg (19, “FL”).
13
14f
G
FL
19
13
STEP 5c
Place panel (14b) [the panel with
the serial plate] over panels (13)
and insert screw (G); into bottom
holes.
18
BL
BR
19
14b
G
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 6
11
a
Insert support (11b) into front leg
(18, “FR”) with holes facing in-
ward. Insert other (11a) into back
leg (18, “BR”) with holes facing
inward.
13
G
11
b
Repeat steps for left side.
G
When all supports are in place
screw holes should be facing each
other as shown in image.
19
BL
18
18
BR
FR
19 FL
STEP 7
Attach seat (22) to supports using
screws (G)
.
22
Repeat step for remaining seat on
opposite side.
G
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 8
Attach drip tray bracket (8) to grill
base (5) using washers (I) and
screws (L).
5
Note: Make sure to use screw
(L) from the blister pack, and
not screw (G) as screw (L) is
shorter than (G).
L
I
L
I
(G)
M6x13
(L)
M6x8
Phillips Head
Screw
Phillips Head
Screw
8
5
STEP 9
G
Position grill base (5) onto seat
(22) as shown. Secure using
washers (I) and screws (G).
I
G
I
5
22
View of grill base (5)
positioned on seats
(22) from below.
22
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 10
Place logo base (28) onto grill
base (5). Secure using washers
(J) and screws (H).
5
J
28
H
23
STEP 11
Note: Hinge for grill base is
larger than hinge for grill lid.
5
24
Attach left bottom hinge (24) to
grill base (5) using washers (C)
and screws (G). [Welded nut on
left bottom hinge (24) should be
facing right when secured.]
C
Repeat step on other side with
right bottom hinge (23), washers
(C) and screws (G). [Welded nut
on right bottom hinge (23) should
be facing left when secured.]
G
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
25
STEP 12
26
Note: Hinge for grill lid is smaller
than hinge for grill base.
1
From inside grill lid, align holes
of left lid hinge (25) to grill lid (1)
holes. Secure with screws (G) and
flat washer (C).
C
Repeat step on other side with
right lid hinge (26), washer (C)
and screw (G).
G
1
STEP 13
Position grill lid (1) on top of grill
base (5), inserting lid hinges (26)
(25) inside bottom hinges (23)
(24).
B
26
23
Align holes and secure hinges us-
ing screw (B).
5
25
24
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 14
*Note: Wing nut is packaged
with temperature gauge.
1
2b
2g
Attach temperature gauge (2g)
and temperature gauge base (2b)
to grill lid (1) using wing nut.
WING NUT
Tip:
Make sure the temperature
readings and Masterbuilt logo
in the gauge are aligned cor-
rectly before tightening down
the wing nut.
FIGURE 2
STEP 15
Place bakelite spacer (F) on grill
lid (1). Attach handle (27)
using washers (J) and screws (D)
as shown.
27
F
J
Make sure lid handle (27) is slop-
ing downward as shown in
FIGURE 2.
27
1
The bakelite spacers (F) should
be angled down and slightly
outward with the larger side of
the spacers going to grill lid and
the smaller side attached to the
handle.
D
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 16
Attach left side shelf (6) to both
supports (11) using screws (G).
11
6
Repeat step on opposite side with
right side shelf (3).
GO BACK AND TIGHTEN ALL
SCREWS AT THIS TIME.
G
Note: The left side shelf is
the shelf with a square notch
in it as seen in FIGURE 1.
NOTCH
6
FIGURE 1
STEP 17
Place reflector plate (9) into
bottom of grill base (5).
9
5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 18
Attach heating element (4) to
grill base (5) using screws (A) as
shown.
5
A
(A)
M5
Thumb Screw
4
STEP 19
Position cooking grate (20) on top
of grill base (5).
Note: The 2 support bars on
cooking grate (20) should
span left to right, with the
grates going front to back.
This alignment is essential
for the next step.
20
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 20
Insert warming rack (21) onto
cooking grate (20), with forks of
warming rack straddling grate as
shown in FIGURE 3.
21
20
5
FIGURE 3
6
10
STEP 21
Plug controller (10) into side of
grill base (5) from below side shelf
(6), coming in at a slight angle,
carefully inserting plug while lifting
so that top of controller slips into
notch in shelf (6).
5
10
5
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
STEP 21
Slide drip tray (7) into drip tray
bracket (8) from the right side.
8
ASSEMBLY IS COMPLETE
7
SAFE STORAGE AND MAINTENANCE
•
•
•
•
Inspect hardware and assembled parts on a regular basis to insure grill is in safe working condition.
ALWAYS allow grill to cool completely before handling.
ALWAYS empty drip tray after use only when ashes have completely cooled.
Clean grill, including special surfaces such as cooking grates with mild cleaning agents. Wipe outside of grill with
damp rag. DO NOT use oven cleaner.
•
•
•
ALWAYS cover and store cold grill in a protected area.
Indoor storage of grill is permissible only if the grill is completely cold. Remember to clean drip tray before storing.
Grill is made of steel and may rust over time. If rusting occurs on outside surfaces, clean area with sand paper or steel
wool, then cover with heat resistant paint, except for stainless steel parts.
•
•
If rusting occurs on the inside surface of grill, clean area with sandpaper or steel wool, then coat with cooking oil,
except for stainless steel parts.
NEVER USE PAINT ON INSIDE SURFACES OF GRILL.
ALWAYS MAKE SURE UNIT IS UNPLUGGED AND COOL
TO THE TOUCH BEFORE CLEANING AND STORING.
REMINDER: NEVER OPERATE THIS GRILL UNDER ANY OVERHEAD CONSTRUCTION. MAINTAIN A
MINIMUM DISTANCE OF 10 FT (3M) FROM OVERHEAD CONSTRUCTION, WALLS OR RAILS.
SEE DIAGRAM BELOW.
Overhead
10 ft (3m)
Construction
Rails
10 ft (3m)
Wall
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Masterbuilt warrants its products to be free from defects in material and workmanship under proper
assembly, normal use and recommended care for 90 days from the date of original retail purchase.
Masterbuilt warranty does not cover paint finish as it may burn off during normal use.
Masterbuilt warranty does not cover rust of the unit.
Masterbuilt requires reasonable proof of purchase for warranty claims and suggests that you keep your
receipt. Upon the expiration of such warranty, all such liability shall terminate.
Within the stated warranty period, Masterbuilt, at its discretion, shall repair or replace defective components
free of charge with owner being responsible for shipping. Should Masterbuilt require return of component(s)
in question for inspection Masterbuilt will be responsible for shipping charges to return requested item.
This warranty excludes property damage sustained due to misuse, abuse, accident, damage arising out of
transportation, or damage incurred by commercial use of this product.
This expressed warranty is the sole warranty given by Masterbuilt and is in lieu of all other warranties,
expressed or implied including implied warranty, merchantability, or fitness for a particular purpose.
Neither Masterbuilt nor the retail establishment selling this product, has authority to make any warranties or
to promise remedies in addition to or inconsistent with those stated above.
Masterbuilt’s maximum liability, in any event, shall not exceed the purchase price of the product paid by
the original consumer/ purchaser. Some states do not allow the exclusion or limitation of incidental or
consequential damages. In such a case, the above limitations or exclusions may not be applicable.
California residents only: Not withstanding this limitation of warranty, the following specific restrictions
apply; if service, repair, or replacement of the product is not commercially practical, the retailer selling the
product or Masterbuilt will refund the purchase price paid for the product, less the amount directly
attributable to use by the original buyer prior to the discovery of the nonconformity. Owner may take the
product to the retail establishment selling this product in order to obtain performance under warranty.
This expressed warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
or complete and return to
Attn: Warranty Registration
Masterbuilt Mfg. Inc.
1 Masterbuilt Court - Columbus, GA 31907
Name: __________________________________ Address :___________________________ City:________________
State/Province: ________ Postal Code: ________________Phone Number: (_____) - ____________
E-mail Address:_______________________________________
*Model Number: ____________________
*Serial Number: ____________________
Purchase Date: _____- ______-_______ Place of Purchase: ____________________________________
*Model Number and Serial Number are located on silver label on back of unit.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Masterbuilt Manufacturing, Inc.
1 Masterbuilt Ct.
Columbus, GA 31907
Customer Service 1-800-489-1581
Download from Www.Somanuals.com. All Manuals Search And Download.
|