Introduction
Thank you for purchasing the LINDY PCIe one Port parallel Card. This
card is equipped with one 1284 centronics parallel interface.
The parallel port include IEEE1284 with speeds up to 15MB/Sec on the
Parallel port.
Port Specification
PCIe 1P (IEEE 1284)
Parallel Port:
•
•
•
•
Chipset: Oxford 952
User Manual
English
IEEE standard: IEEE 1284 Interface
Max. Speed: Up to 15MB/Sec
DB 25 Female Connector
Package Contents
°
°
°
1 x LINDY PCI 1P Card
LINDY User manual
LINDY Driver CD
Installation
1. Turn off the power of your computer and remove the power
cable
2. Install the PCI card into an available PCI slot in your computer
3. Connect the peripheral ie Printer, Modem, etc. to the adapters
port
4. Re-connect the power cable & turn on the power of your
computer
PCI device listing display (for example…)
LINDY No. 51185
Bus Device Func
Vendor ID Device
ID
Device Class IRQ
IDE Controller 14
No
0
No
7
No
1
8086
7010
0
13
0
1409
7168
Simple COMM. 10
Controller
Certifications
FCC Certifications
If the Vendor ID, Device ID, Device Class or IRQ aren’t displayed or an
error occurs, please try another PCI slot.
Once the hardware has installed correctly you can start installing the
software from the driver CD.
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in
a
commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received;
including interference that may cause undesired operation.
Pin Assignments
Parallel 25 Pin female connector pin assignments:
Parallel 25 Pin female connector :
Pin
1
Signal
STROBE
DATA 0
DATA 1
DATA 2
DATA 3
DATA 4
DATA 5
DATA 6
DATA 7
Pin
10
11
12
13
14
15
16
17
18
Signal
ACKNOWLEDGE 19
BUSY
PAPER EMPTY
SELECT
AUTO FEED
ERROR
Pin
Signal
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
GROUND
2
20
21
22
23
24
25
26
3
4
5
CE Certification
6
This equipment complies with the requirements relating to
electromagnetic compatibility, EN 55024 and EN55022 class A for ITE,
EN61000-3-2/-3 the essential protection requirement of Council Directive
89/336/EEC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
7
INIT
8
SELECT INPUT
GROUND
9
Technical Specifications
Recycling Information
•
•
Support x17 x1,x2,x4,x8,x16ΰlaneαPCI-Express Bus
connector keys
Operating system: DOS, WIN 9.x, ME, NT, 2000, XP, 2003
Server, VISTA, LINUX,
WEEE (Waste of Electrical and Electronic Equipment),
Recycling of Electronic Products
•
•
•
•
•
•
Support ECP, EPP and SPP
Ready of the Intel and AMD 32/64-bit CPU System
Built-in 32 byte hardware FIFO
IRQ and IO address assigned by System
Certified by Microsoft WHQL, CE, FCC approval
PCB: 80 x 65 mm
United Kingdom
In 2006 the European Union introduced regulations (WEEE) for the
collection and recycling of all waste electrical and electronic equipment.
It is no longer allowable to simply throw away electrical and electronic
equipment. Instead, these products must enter the recycling process.
Each individual EU member state has implemented the WEEE
regulations into national law in slightly different ways. Please follow your
Download from Www.Somanuals.com. All Manuals Search And Download.
|