829 LEG CURL/EXTENSION
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
USER’S GUIDE
CLASS H
PART # 7078201
REV. B
1
Version: 829107
Revision: 06/26/01
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
Tools Required forAssembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* Tape measure
Bolt Length Ruler
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.
BOLT LENGTH
BOLT LENGTH RULER:
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
3
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1’
2’
3’
4’
5’
1’
2’
3’
4’
5’
6’
1 Square = 1’ X 1’
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
KEY PART #
DESCRIPTION
FRONT SUPPORTTUBE
BACK PADADJUST TUBE
BACK PAD SUPPORTTUBE
1-3/4 SQ X 5" TUBE
1-3/4 SQ X 13-1/2" TUBE
LEG CURL/EXTENSION
BACK PADASSY
QTY
1
KEY PART #
DESCRIPTION
3/8 X 3" BOLT
QTY
8
1
2
3
4
5
6
7
8
9
6259108
6625402
6625502
6216702
6668202
6662002
6661221
6661621
6662208
20 3102904
21 3102906
22 3102917
23 3202102
24 3102501
25 3102802
26 3102804
27 3102807
28 6405201
29 6692601
30 3102416
31 6406401
32 3104301
33 6416601
34 6020601
35 3105401
36 3103101
37 6467001
1
3/8 X 4" BOLT
2
1
1/2 X 4" BOLT
1
1
1/2 X 7" BOLT
1
1
3/8" FLAT WASHER
3/8" NYLOCK NUT
1/2" LOW HT. NYLOCK NUT
3/8" LOW HT. NYLOCK NUT
2" SQ END CAP
20
4
1
1
2
SEATPADASSY
1
2
LEG EXT HANDLE RHT
LEG EXT HANDLE LFT
LEG FRAME
1
3
10 6662308
11 6668508
12 6668808
13 6125101
14 6549301
15 6194601
16 6628302
17 6412001
18 6466901
19 3102909
1
3 X 2" END CAP
2
1
2 X 1" END CAP
4
REAR BASE LEG
1
HINGE TAB
2
3/4 X 16" TUBE
2
3/4" SQ RUBBER BUMPER
1-1/2 X 3/4" GLIDE (QTY 8)
1/2" FLANGE BEARING
STARLOCK COLLAR
1-1/4 X 5" GRIP
1
3/4 X 17" TUBE
1
2
4 X 7" ROLLER PAD
1/8 X 2 X 8" PLATE
3/8” DIA SPRING PIN
1/2" DIA SPRING PIN
3/8 X 1" BOLT
6
2
1
6
2
4
1
PARABODY LOGO END CAP
4
4
LEG EXTENSION
LEG CURL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
36
12
37
STEP 1: Insert four PARABODY LOGO END
CAPS(37) into the ends of REAR BASE
LEG (12) and FRONT BASE SUPPORT
(1). See FIGURE 1.
1
37
STEP 2: Slide two 1-1/4 x 5” GRIPS (36) over tubes
on REAR BASE LEG (12). See FIGURE
1.
FIGURE 1
12
11
25
STEP 3: Securely assemble REAR BASE LEG (12)
to LEG FRAME (11) using two 3/8 X 3”
BOLTS (20), four 3/8” FLAT WASHERS
(24), and two 3/8” NYLOCK NUTS (25).
See FIGURE 2.
24
24
20 3/8 X 3”
FIGURE 2
11
STEP 4: Securely assemble FRONT BASE SUP-
PORT (1) to LEG FRAME (11) using two
3/8 X 3” BOLTS (20), four 3/8” FLAT
WASHERS (24), and two 3/8” NYLOCK
NUTS (25). See FIGURE 3.
1
25
24
24
3/8 X 3” 20
FIGURE 3
9
10
&
STEP 5: Slide two 1-1/4 X 5" GRIPS (36) over
RIGHT LEG EXT HANDLE (9) & LEFT
LEG EXT HANDLE (10). See FIGURE 4.
36
FIGURE 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 5
27 LOW HEIGHT
24
29
STEP 6:Securely assemble RIGHT (9) & LEFT (10)
LEG EXTHANDLES to LEG FRAME (11)
using two 3/8 X 4” BOLTS (21), four 3/8”
FLATWASHERS (24) , and two 3/8” LOW
HEIGHT NYLOCK NUTS (27). See FIG-
URE 5.
10
29
11
STEP 7:Insert two 3 X 2” END CAPS (29) into
9
the leg frame as shown in FIGURE 5.
24
18
21 3/8 X 4”
FIGURE 6
STEP 8:Securely assemble one 1/2” SPRING PIN AS-
SEMBLY (18) into the spring pin barrel on the
LEG FRAME (11) as shown in FIGURE 6.
11
FIGURE 7
2
STEP 9:Insert four 2 X 1” END CAPS (30) into the ends
of the BACK PAD ADJUST TUBE (2) & BACK
PAD SUPPORT TUBE (3). See FIGURE 7.
3
30
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 8
STEP 10: Securely assemble BACK PAD ADJUST
TUBE (2) & BACK PAD SUPPORT TUBE
(3) to LEG FRAME (11) using one 1/2 X 7”
BOLT (23) and one 1/2” LOW HEIGHT
NYLOCK NUT (26). (NOTE: SECURELY
TIGHTEN BOLT THEN BACK NUT OFF
1/4 TURN TO ALLOW THE TWO PARTS
TO ROTATE FREELY.) See FIGURE 8.
3
26
2
11
23 1/2 X 7”
FIGURE 9
STEP 11: Securely attach the BACK PAD (7)
to the BACK PAD TUBES (2 & 3)
using four 3/8 X 3” BOLTS (20)
and four 3/8” FLAT WASHERS
(24). See FIGURE 9.
20 3/8 X 3”
3
24
7
2
FIGURE 10
19 3/8 X 1”
24
16
STEP 12: Securely fasten 2 X 8” PLATE (16) to bottom of SEAT
PAD (8) using two 3/8 X 1” BOLTS (19) and two 3/8”
FLAT WASHERS (24). See FIGURE 10.
8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
31
FIGURE 11
STEP 13: Slide two HINGE TABS (31) over posts on
LEG FRAME (11). See FIGURE 11.
11
31
FIGURE 12
8
STEP 14: Securely attach the SEAT PAD (8) to the
HINGE TABS (31) using two 3/8 X 1”
BOLTS (19) and two 3/8” FLAT WASH-
ERS (24). See FIGURE 12.
31
24
19 3/8 X 1”
STEP 15: Attach two ROLLER PADS (15) to the
LEG FRAME (11) using one 17” ROLLER
PAD SHAFT (14) and two STARLOCK
COLLARS (35). See FIGURE 13.
35
15
11
14
15
35
FIGURE 13
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
9
4
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
5
33
STEP 16: Attach eight 1-1/2” X 3/4” GLIDES (33) to 5”
ROLLER PAD ADJUSTER (4) and attach eight
1-1/2” X 3/4” GLIDES (33) to 13-1/2” ROLLER
PAD ADJUSTER (5) as shown in FIGURE 14.
FIGURE 14
6
STEP 17: Securely assemble two 3/8” SPRING PIN AS-
SEMBLIES (17) into the spring pin barrels on
the LEG CURL/EXTENSION (6) as shown in
FIGURE 15.
17
17
FIGURE 15
28
6
4
STEP 18: Insert 5” & 13-1/2” ROLLER PAD
ADJUSTERS (4 & 5) in the ends of the
LEG CURL/EXTENSION (6). Pull back
on SPRING PINS until ROLLER PAD
ADJUSTERS (4 & 5) lock in place. See
FIGURE 16.
28
STEP 19: Insert three 2” SQUARE END CAPS (28)
into the ends of the LEG CURL/EXTEN-
SION (6). See FIGURE 16.
5
28
FIGURE 16
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 20:Insert two 1/2” FLANGE BEARINGS
(34) into the LEG CURL/EXTENSION
(6). See FIGURE 17.
26 LOW HEIGHT
STEP 21:Securely assemble LEG CURL/EX-
TENSION (6) to LEG FRAME (11)
using one 1/2 X 4” BOLT (22) and one
1/2” LOW HEIGHT NYLOCK NUT
(26). (NOTE: SECURELY TIGHT-
EN BOLT THEN BACK NUT OFF
1/4 TURN TO ALLOW THE PART
TO ROTATE FREELY.) See FIG-
URE 17
6
34
11
32
22 1/2 X 4”
STEP 22:Attach one 3/4” SQUARE RUBBER
BUMPER (32) between the contact point
of the LEG CURL/EXTENSION (6) and
the LEG FRAME (11).See FIGURE 17.
FIGURE 17
STEP 23:Attach four ROLLER PADS (15) to the LEG CURL/EXTENSION (6) using two 16”
ROLLER PAD SHAFTS (13) and four STARLOCK COLLARS (35). See FIGURE 18.
35
15
THIS CONCLUDES THEASSEMBLY
13
OF THE PARABODY 829
LEG CURL/EXTENSION
6
FIGURE 18
1/2
1/2
1/2
1/2
1/2
1/2
0
1
2
3
4
5
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Please note:
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy
water. Touch-up paint can be purchased from your ParaBody customer service representative
at (800) 328-9714.
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.
Failure to do so may result in serious injury
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND
MAIL BACK.
MODEL #________________________
SERIAL #_________________________
DATE OF PURCHASE: _____________
DEALERS NAME: _________________
DEALERS PHONE #_______________
Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,
ParaBody will repair or replace them, at its option. Terms: Three (3) years.
4. CONDITIONSAND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of
ParaBody will void this Limited Warranty.
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;
and c. all necessary or incidental costs related to installation of the replacement parts.
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage
incurred in shipping.
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly
drawing included with your assembly instruction); (iv) a description of the nature of the problem.
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the
above limitation or exclusion may not apply to you.
NOTES:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
LIFE FITNESS
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.
Tel: 763.323.4500 Fax: 763.323.4797
800.328.9714 (Toll-free within the U.S. and Canada)
INTERNATIONALOFFICES
Life FitnessAtlantic BV
Life Fitness (UK) Ltd.
QueenAdelaide
Ely, Cambs CB7 4UB
United Kingdom
Phone CSS: (01353) 665507
Fax CSS: (01353) 666719
Atlantic Headquarters
Bijdorpplein 25-31
2992 LB Barendrecht
The Netherlands
Phone: (180) 646 666
Fax: (180) 646 703
Life Fitness EUROPE GmbH
Siemensstrasse 3
Life Fitness Benelux N.V.
Bijdorpplein 25-31
85716 Unterschleissheim
Germany
2992 LB Barendrecht
The Netherlands
Phone: (089) 31 77 51-0
Fax: (089) 31 77 51 99
Phone: 31 (180) 64 66 69
Fax: 31 (180) 64 66 99
Life Fitness Japan
8/F, Nippon Brunswick Building
5-27-7 Sendagaya
Shibuya-Ku, Tokyo 151-0051
Japan
Phone: 81 (3) 3359-4309
Fax: 81 (3) 3359-4307
Life Fitness Italia S.R.L.
Via Elvas 92
39042 Bressanone
Italy
Phone: 39 (472) 835-470
Fax: 39 (472) 833-150
Life Fitness Do Brazil
Al. Rio Negro, 433-Predio 2-Sala 2
3º andar (Confab)
Aplhaville-Barueri-Sao Paulo
CEP: 06454-904
Life FitnessAsia Pacific Limited
Room 2610, Miramar Tower
132 Nathan Road, Tsimshatsui
Kowloon, Hong Kong
Phone: (852) 2891-6677
Fax: (852) 2575-6001
Brazil
Phone: 55 (11)7295-2217
Fax: 55 (11) 7295-2218
Download from Www.Somanuals.com.1A4ll Manuals Search And Download.
|