DVD Standard
THE LEADER IN AUDIO ENGINEERING
Instructions for Use
Owner’s Reference
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Page
1
INTRODUCTION
DEFINITION OF TERMS
UNPACKING
2
4
PLACEMENT
5
AC Power Guidelines
GETTING STARTED
5
6
FRONT PANEL DESCRIPTION
BACK PANEL DESCRIPTION
REMOTE CONTROL DESCRIPTION
11
15
20
Battery Installation and Removal
Remote Control Functions
20
20
CONNECTING THE DVD STANDARD TO YOUR SYSTEM
Connection Steps
25
25
26
OPERATING YOUR DVD STANDARD
On/Off/Stand-by
How to Play a Disc
How to Write a Program
How to Create an A-B Loop
26
26
27
29
SYSTEM SETUP OVERVIEW
SYSTEM SETUP
30
31
Configuration Menu
Faroudja Menu
Audio Menu
33
40
46
51
Parental Menu
WARRANTY
57
58
RETURN AUTHORIZATION PROCEDURE
Krell DVD Standard
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Illustrations
Page
10
FIGURE 1 The DVD Standard Front Panel
FIGURE 2 The DVD Standard Back Panel
FIGURE 3 The DVD Standard Remote Control
14
19
iv
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for your purchase of the Krell DVD Standard.
The DVD Standard is designed to provide the finest Digital Video
Disc image available, allowing you to seamlessly integrate the DVD
Standard with the highest quality video display devices. The DVD
Standard’s tremendous and carefully regulated power supply results
in picture stability even during line fluctuations. Advanced drive
mechanisms provide superior disc reading capabilities.
The DVD Standard, Krell’s first video source component, is engi-
neered with the latest technology from Faroudja Laboratories, widely
recognized as a video technology leader. The FLI 2200 line doubler
together with the FLI 2220 enhancer support progressive scan
(480p) video signals, producing a video image for standard and wide
screens that is bright, detailed, and free of any motion artifact. The
DVD Standard has progressive scan video connections as well as
standard component, S-video, and composite video connections. The
RGB/YPbPr switch provides maximum flexibility for progressive scan
connections.
The DVD Standard wireless infrared remote control and RS-232,
RC-5, and 12 VDC remote connection options on the back panel
allow you to integrate the DVD Standard into advanced control sys-
tems. The user-friendly setup menu provides a variety of audio,
video, and access control options for optimum configuration and
enjoyment of your DVD Standard and home theater system.
This owner’s reference manual contains important information on
placement, connection, and operation of your DVD Standard. Please
read this information carefully. A thorough understanding of these
details will help ensure satisfactory operation and long life for your
DVD Standard and related system components.
Krell DVD Standard
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Definition of Terms
Following are the definitions of key terms used in your owner’s refer-
ence manual.
INPUT AND OUTPUT
CONNECTIONS
Balanced
A symmetrical input or output circuit that has equal impedance from
both input terminals to a common ground reference point. The indus-
try standard for professional and sound recording installations, bal-
anced connections have 6 dB more gain than single-ended connec-
tions and allow the use of long interconnect cables. Balanced con-
nections are more immune to induced noise from the system or the
environment.
Single-ended
A two-wire input or output circuit. Use care when using single-ended
connections. Turn the system off prior to making or breaking single-
ended connections. Single-ended connections are not recommended
for connections requiring long cable runs.
Off
OPERATION
When the AC power cord is unplugged from the AC power source,
the component is off.
Stand-by Mode
When the DVD Standard is connected to AC power, the red stand-by
LED illuminates. This indicates that the component is in stand-by
mode, a low power consumption status that keeps the audio and reg-
ulator circuits at idle. Krell recommends leaving the component in the
stand-by mode when not playing a disc.
Operational Mode
When the power button on the front panel or power key on the
remote control is pressed and the blue power LED illuminates, the
component is in the operational mode and ready to play a disc.
2
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Definition of Terms
VIDEO TECHNOLOGY
Composite Video
An encoded video signal that includes horizontal and vertical syn-
chronizing information.
Component Video
A video signal that uses three wires to convey luminance (Y), red
minus luminance (R-Y), and blue minus luminance (B-Y) signals.
Progressive Scan Video
Video signals (noninterlaced) that build screen content in one pass
rather than the two passes required for standard (interlaced) video.
This technology eliminates motion artifact and screen line and pro-
duces film-quality pictures.
RGB
Red, green, and blue, the three primary colors used in video
processing.
S-Video
Video signal that separately transmits the color and luminance com-
ponents of the video signal but does not use three separate wires as
does component video.
YPbPr
One way of designating color difference signals. Y = the luminance
signal, Pb = the red minus luminance (R-Y) signal, and Pb = the blue
minus luminance (B-Y) signal.
Krell DVD Standard
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Follow these steps to safely unpack your DVD Standard:
1. Open the shipping box and remove the top layer of foam. You
see these items:
1
1
1
1
1
1
Krell DVD Standard
IEC connector (AC power) cord
12 VDC (12 V trigger) cable
DVD remote control
CR2025 lithium battery
packet containing the owner’s reference manual, the
RS-232 port developer’s reference, and the warranty
registration card.
2. Grasp the underside of the foam end-caps that encase the DVD
Standard and lift it straight out of the shipping box.
3. Place the DVD Standard in a safe location and remove the end-
caps and protective plastic wrapping.
Only one person needed.
Notes
If any of these items are not included in the shipping box, please contact
your authorized Krell dealer, distributor, or Krell for assistance.
Save all packing materials. If you ship your DVD Standard in the future,
repack the unit in its original packaging to prevent transit damage. See
Return Authorization Procedure, on page 58, for more information.
4
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
Before you install the DVD Standard into your system, review the
following guidelines to choose the location for the component. This
will facilitate a clean, trouble-free installation. The DVD Standard
does not require any type of special rack or cabinet for installation.
Place the DVD Standard on a firm, level surface, away from exces-
sive heat, humidity, or moisture. The DVD Standard requires at least
two inches (5 cm) of clearance on each side and at least two inches
(5 cm) of clearance above and below the component to provide ade-
quate ventilation. Installations inside cabinetry may need extra venti-
lation.
Note
The DVD Standard incorporates an advanced suspension system and does
not require additional mass coupling or isolation. You may experiment with
feet or cones as long as they are not permanently affixed to the unit. Any
unauthorized modifications to the unit or electronics will void the warranty.
IMPORTANT
Do not attach enhancement accessories such as rings, mats, or
dampers to individual discs. These accessories may interfere with the
disc transport, resulting in erratic playback and/or poor performance.
AC Power
Guidelines
The DVD Standard has superb regulation and does not require a
dedicated AC circuit. Operate the DVD Standard only with the power
cord supplied.
Avoid connections through extension cords or multiple AC adapters.
High quality 15 amp grounded AC strips are acceptable. High quality
AC line conditioners or filters may be used if they are grounded and
meet or exceed the unit’s power supply rating of 100 VA.
Please contact your Krell dealer, distributor, or Krell before using any
device designed to alter or stabilize the AC power for the DVD
Standard.
Krell DVD Standard
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
READ THIS FIRST
To connect the DVD Standard to your video monitor, you need to:
connect to AC power, choose your video format, choose and then
connect video outputs, and configure the DVD Standard to match
your television format. These steps are explained below.
Match the video format (NTSC/PAL) of the monitor and the video sig-
nal of the DVD Standard to avoid a distorted picture.
IMPORTANT
Connect to AC Power
Step 1
Plug the AC cord into the wall outlet. The red stand-by LED (3) illumi-
nates.
Choose the Video Format
Step 2
Set the NTSC/PAL switch (25) on the back panel to the format that
matches your video monitor. See your monitor’s owner’s manual for
information.
IMPORTANT
The NTSC/PAL switch is active only when the DVD Standard is in the
stand-by mode. Changing the switch position while the component is
in the operational mode will not change the video format.
Choose and Connect the Video Outputs
Step 3
Choose the output that matches your video monitor. The DVD
Standard supports both progressive scan video (noninterlaced) and
standard video (interlaced) outputs. Options for each are explained
on the following pages.
The component YPbPr outputs will provide the best quality picture
when connected to a television capable of accepting a 480p sig-
nal. This includes most plasma, D-ILA, DLP, and HDTV ready
televisions.
6
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started, continued
Progressive Scan
(Noninterlaced)
Video Outputs
The DVD Standard supports progressive scan (480p) video signals.
Progressive scan builds video screen content in one pass (as
opposed to two passes for nonprogressive or interlaced video), thus
providing better quality picture. Progressive video can also be con-
nected to a computer monitor.
The following table details the different progressive video signals,
connectors, labels, and formats supported by the DVD Standard.
Note
To use the progressive scan video outputs on the DVD Standard, the tele-
vision or video monitor must have a 31.5 kHz horizontal scan rate and a
progressive or 480p video input.
Video
Signal
Type of
Connector
Most Commonly
Labeled As
Format
Standard
RGB
BNC
BNC
RGB video,
sync on green
NTSC or PAL
NTSC or PAL
NTSC or PAL
RGB, HSYNC,
VSYNC
RGB video,
component sync
VGA
Computer-type
VGA connector
(DB-15)
VGA, computer,
PC, DB-15
Component
(YPbPr)
RCA
Component video,
YPbPr, YCbCr,
480p,
NTSC or PAL
progressive
All of the progressive video outputs should be of comparable quality.
Multiple formats are provided for compatibility with various televi-
sions, monitors, and projectors. The DVD Standard has maximum
progressive scan flexibility. You can send a progressive signal to any
of the three connectors. For example, if the RGB/YPbPr switch is set
to RGB, then the RGB, YPbPr, and DB-15 outputs will all output
RGB signals.
The RGB/YPbPr switch is active only when the DVD Standard is in the
stand-by mode. Changing the switch position while the component is
in the operational mode will not change the video output format.
IMPORTANT
See Back Panel Description, on page 15, for more information
about progressive scan video outputs.
Krell DVD Standard
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started, continued
Standard (Interlaced)
Video Outputs
The DVD Standard also features standard composite, S-video, and
component connections.
The following table details the different standard video signals, con-
nectors, labels, and formats supported by the DVD Standard.
Video
Signal
Type of
Connector
Most Commonly
Labeled As
Format
Standard
Standard
Composite
Single-ended
RCA
Video,
Composite
NTSC or PAL
NTSC or PAL
NTSC or PAL
Standard
S-Video
4 pin mini-DIN
S, SV, S-Video
Standard
Component
Single-ended
RCA
Component,
YPbPr, YCbCr
Choosing A Standard Video Signal
This section describes the three standard video options.
Component Video. Choose the component connection for video
monitors that have component (YPbPr or YCbCr) connections.
Component video is the most accurate standard video signal, using
three wires to convey luminance, red minus luminance, and blue
minus luminance signals. These signals bypass television circuitry
required to process S-video signals, eliminating cross-color contami-
nation and resulting in more reliable, correct color.
S-Video. Choose the S-video connection for video monitors that
have S-video connections but do not have component connections.
S-video separately transmits the color and luminance components of
the video signal but does not use three separate wires as does com-
ponent video. The S-video signals bypass television circuitry required
by composite video, reducing cross-contamination of color and black
and white signals, and reducing video noise.
Composite Video. Choose the composite connection for video mon-
itors that are not equipped with component video or S-video.
8
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started, continued
Configure TV Type
Step 4
Configure the DVD Standard to match your television aspect ratio
(4:3 standard or 16:9 wide-screen) through the setup menu. Follow
these steps:
a. Turn on your television or video monitor.
b. Press the power button (1) or key (38) on the DVD Standard.
The blue power LED (2) illuminates.
c. Press the setup button on the front panel (19) or the setup key on
the remote control (44). The setup menu appears on the video
display. The configuration option is highlighted.
d. Press the ᮣ button (16) or key (45) to reveal configuration
options.
e. Press the ᮡ button (16) or key (45) to select TV TYPE. Choose
standard screen size 4:3 LT (letterbox with black box at the top
and bottom margin of the screen), standard screen size 4:3 PS
(pan and scan picture extends to the screen margins) or 16:9
(wide-screen).
f. Press the setup button or key to exit the setup menu.
IMPORTANT
Stop disc playback before changing the aspect ratio. Changes will not
take effect while disc is being played.
After you have connected and configured your video monitor and the
DVD Standard, you’re ready to connect the rest of your system. See
Connecting the DVD Standard to Your System, on page 25.
Krell DVD Standard
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1 The DVD Standard Front Panel
10
9 7 12
11 8
13
15
16
17
16
DVD Standard
TRACK
SEARCH
OPEN/CLOSE
REPEAT
PAUSE
STOP
PLAY
STAND-BY
POWER
MENU
SETUP
DVD
5 3 21
6
4
14
18
19
Menu and Setup
Functions
16 Directional Buttons
17 Enter Button
18 Menu Button
19 Setup Button
Power
Disc Functions
1
Power Button
Power LED
5
6
7
8
9
Repeat Button
Pause Button
Stop Button
Play Button
Track Forward Button
2
3
4
Stand-by LED
Infrared Sensor
10 Track Back Button
11 Search Forward Button
12 Search Back Button
13 Open/Close Button
14 Disc Transport
15 Front Panel Display
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Description
See Figure 1 on page 10
POWER
1 Power Button
Use this button to switch the DVD Standard from the stand-by to the
operational mode.
2 Power LED
The blue power LED illuminates when the DVD Standard is in the
operational mode.
3 Stand-by LED
The red stand-by LED illuminates when the DVD Standard is
plugged into AC power and is in the stand-by mode.
4 Infrared Sensor
The infrared sensor receives commands from the DVD Standard
remote control. For proper remote control operation, make sure the
infrared sensor is not covered or obstructed.
5 Repeat Button
DISC FUNCTIONS
Use this button to activate the repeat options, which include:
ALL REPEAT
(repeats entire disc)
TITLE REPEAT
CHAPTER REPEAT
REPEAT OFF
(repeats all chapters in current title)
(repeats currently playing chapter)
(clears repeat function)
The repeat option appears briefly in the upper left corner of the video
display. The last item scrolled to is automatically selected. To clear
the repeat command:
— select REPEAT OFF from the repeat menu
— press the stop button or key twice
— press the clear button or key
— press the power button or key to place the component in the
stand-by mode.
6 Pause Button
Use this button to pause disc playback. The video display indicates
PAUSE in the top right corner. To resume playback, press the pause or
play button or key.
Krell DVD Standard
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Description, continued
DISC FUNCTIONS
7 Stop Button
Use this key to stop DVD playback. The video display shows the fol-
lowing message:
WHEN PLAY IS PUSHED, THE PLAYER WILL PLAY FROM WHERE YOU
STOPPED. TO START FROM THE BEGINNING, PRESS STOP AGAIN.
8 Play Button
Use this button to begin or resume DVD playback.
9 Track Forward Button
Use this button to move forward one chapter or track. The upper left
corner of the video display shows SEARCH and the currently playing
chapter or track number.
10 Track Back Button
Use this button to move back one chapter or track. The upper left
corner of the video display shows SEARCH and the currently playing
chapter or track number.
11 Search Forward Button
Use this button to access the two fast-forward playback modes when
in the play mode. Press once: the right corner of the video display
shows FF1. Press again: the screen shows FF2. Use the search for-
ward button to switch between the slower (FF1) and faster (FF2)
modes. Press the play button or key to resume normal playback.
Also use this button for single step forward when in the pause mode.
12 Search Back Button
Use this button to access the two fast-reverse playback modes when
in the play mode. Press once: the right corner of the video display
screen shows FR1. Press again: the screen shows FR2. Use the
search back button to switch between the slower (FR1) and faster
(FR2) modes. Press the play button or key to resume normal play-
back. Also use this button for single step forward when in the pause
mode.
13 Open/Close Button
Use this button to open and close the disc transport.
14 Disc Transport
The disc transport holds the DVD.
15 Front Panel Display
The front panel display shows currently playing title and chapter
numbers, elapsed time, repeat mode, and disc status.
12
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel Description, continued
MENU AND SETUP
FUNCTIONS
16 Directional Buttons
Use these buttons to navigate the disc and setup menus.
17 Enter Button
Use this button to set selected menu or program items.
18 Menu Button
Use this button to access the disc menu. Use the directional buttons
or keys to move through the menu. Press enter to select the desired
menu item. Disc playback pauses automatically when you enter the
menu.
19 Setup Button
Use this button to access the DVD Standard setup menu. The setup
menu allows you to customize your DVD Standard configuration, dis-
play, and audio, and to set parental controls. Press the setup button
again to exit the setup menu. See System Setup, on page 31, for
information on customizing the DVD Standard.
You can access the setup menu during disc playback. The material will play
in the background while you adjust settings.
Note
Krell DVD Standard
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2 The DVD Standard Back Panel
23 22
26
29
34
36
VIDEO OUT
COMPOSITE
PROGRESSIVE SCAN
VIDEO OUT
ANALOG OUTPUTS
LEFT
DVD Standard
R
S-VIDEO
G
RS-232
RC-5
IN
12VDC
OUT IN
COMPONENT
RIGHT
LEFT
B
Y
Y
Pb
Pr
Pb
Pr
HSYNC
50/60Hz
DIGITAL OUTPUTS
VSYNC
RGB
RIGHT
NTSC
PAL
YPbPr
OPTICS
COAX
NO USER SERVICEABLE PARTS INSIDE
MADE IN USA
20
21
24
25
27 28
31
30
33
32
35
37
Analog Audio Outputs
20 Left and Right Balanced
Audio Outputs
21 Left and Right Single-ended
Audio Outputs
Progressive Scan
Video Outputs
26 Progressive 480p Video
Outputs R, G, and B
27 HSYNC 480p Horizontal
Sync Output
Digital Audio Outputs
32 Coaxial Digital Output
33 Optics Digital Output
Remote Connections
34 RS-232 Communication Port
35 RC-5 In
Standard Video Outputs
22 Composite Standard
Video Output
23 S-Video Standard
Video Output
28 VSYNC 480p Vertical
Sync Output
36 12 VDC Out and In
29 DB-15 Progressive
RGB/YPbPr Output
30 Progressive Video
Outputs Y, Pb, and Pr
31 RGB/YPbPr Switch
Power
37 IEC Connector
24 Component Standard
Video Output
25 NTSC/PAL Switch
Download from Www.Somanuals.com. All Manuals Search And Download.
Back Panel Description
See Figure 2 on page 14
ANALOG AUDIO
OUTPUTS
20 Left and Right Balanced Audio Outputs
The DVD Standard is equipped with one pair of left and right bal-
anced analog audio outputs via XLR connectors.
21 Left and Right Single-ended Audio Outputs
The DVD Standard is equipped with one pair of left and right single-
ended analog audio outputs via RCA connectors.
STANDARD VIDEO
OUTPUTS
22 Composite Standard Video Output
The DVD Standard is equipped with a composite standard video out-
put via an RCA connector.
23 S-Video Standard Video Output
The DVD Standard is equipped with an S-video output via a 4 pin
mini-DIN connector.
24 Component Standard Video Output
The DVD Standard is equipped with a component standard video
output via RCA connectors. Component video uses three wires
(labeled Y, Pb, and Pr on the back panel) to convey the video signal.
25 NTSC/PAL Switch
The DVD Standard is equipped with a switch to set the video format
of the video signal to NTSC or PAL.
26 Progressive 480p Video Outputs R, G, and B
The DVD Standard is equipped with a progressive RGB video output
via BNC connectors.
PROGRESSIVE SCAN
VIDEO OUTPUTS
If you playback Macrovision-encoded DVDs using the RGB outputs, the
resulting picture will be tinged with green. Macrovision does not support the
RGB format.
Note
Krell DVD Standard
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Back Panel Description, continued
PROGRESSIVE SCAN
VIDEO OUTPUTS,
continued
27 HSYNC 480p Horizontal Sync Output
The DVD Standard is equipped with an HSYNC Horizontal Sync
Output that works with the Progressive 480p Video Output. HSYNC
and VSYNC are the component sync signals for the progressive
RGB outputs.
28 VSYNC 480p Vertical Sync Output
The DVD Standard is equipped with a VSYNC Vertical Sync Output
that works with the Progressive 480p Video Output. HSYNC and
VSYNC are the component sync signals for the progressive RGB
outputs.
29 DB-15 Progressive RGB/YPbPr Output
The DVD Standard is equipped with a DB-15 connector for connec-
tion to a computer monitor or video monitor.
30 Progressive Video Outputs Y, Pb, and Pr
The DVD Standard is equipped with progressive scan video outputs
Y, Pb, and Pr via RCA connectors.
31 RGB/YPbPr Switch
Use this switch to select RGB or YPbPr modes.
IMPORTANT
If the RGB/YPbPr switch is set for RGB, then all the progressive video
outputs will output RGB signals. If the switch is set for YPbPr, all the
progressive video outputs will output YPbPr signals.
16
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Back Panel Description, continued
Note
The RGB/YPbPr switch is active only when the DVD Standard is in the
stand-by mode. Changing the switch position while the component is in the
operational mode will not change the video format.
DIGITAL AUDIO
OUTPUTS
32 Coaxial Digital Output
The DVD Standard is equipped with one S/PDIF coaxial digital audio
output via an RCA connector.
33 Optics Digital Output
The DVD Standard is equipped with one EIAJ optics digital audio
output via a TosLink connector.
BACK PANEL
REMOTE
CONNECTIONS
34 RS-232 Communication Port
The DVD Standard is equipped with an RS-232 communication port,
which receives messages from a computer-based control system,
providing more intelligent control of the DVD Standard. For more
information, see RS-232 Port: Sending Commands and Interpret-
ing Data, the developer’s reference shipped with the DVD Standard.
35 RC-5 In
The RC-5 input makes custom installation easy and secure by accept-
ing baseband RC-5 commands from hardwired remote controllers.
Krell DVD Standard
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Back Panel Description, continued
BACK PANEL
REMOTE CONNECTIONS,
continued
36 12 VDC Out and In
The 12 VDC output sends a 12 Volt power on/off signal to other Krell
components via a 12 V cable, as well as to other devices that incor-
porate a 12 V power on/off trigger input. The 12 VDC input receives
12 Volt power on/off signals from other Krell components and devices
that incorporate a 12 V trigger. The 12 VDC out and in connections
let you control the operational and stand-by modes of components
with 12 V triggers allowing whole systems or parts of systems to be
easily coordinated.
Notes
When the DVD Standard is in the operational mode, 12 VDC output
provides 12 V of DC output. When the DVD Standard is in the stand-by
mode or off, DC output is 0 V.
12 VDC Out (12 V trigger) current is limited to 30 mA.
Consult the owner’s manual of each component used in a custom installa-
tion to take full advantage of the DVD Standard’s remote capability.
POWER
37 IEC Connector
The DVD Standard is equipped with a standard female IEC power
connector, for use with the AC power cord.
18
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3 The DVD Standard Remote Control
Power
38 Power Key
Power
Title
Audio
Subtitle
Menu
Angle
Setup
Repeat
A-B
38
41
40
Advanced Disc Functions
39
39 Audio Key
40 Subtitle Key
41 Angle Key
42 Title Key
44
43
42
48
45
Menu and Setup Functions
43 Menu Key
44 Setup Key
45 Directional Keys
46 Enter Key
Ret
Disp
46
47
59
49
47 Ret(urn) Key
55
54
51
50
53
52
Disc Functions
48 Repeat Key
57
56
49 Disp(lay) Key
50 Track Forward Key
51 Track Back Key
52 Search Forward Key
53 Search Back Key
54 Pause Key
55 Play Key
56 Open/Close Key
57 Stop Key
1
5
9
2
6
0
3
7
4
8
58
60
61
Prog
Clr
58 Numeric Keys
59 A-B Key
Programming Functions
60 Clr (Clear) Key
61 Prog(ram) Key
Krell DVD Standard
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Description
See Figure 3 on page 19
The DVD Standard remote control uses one CR2025 lithium battery,
which is included with the shipment.
Battery Installation
and Removal
To open the battery compartment on the back of the remote control:
1. Place the remote face down on the table.
2. Use your thumbnail or a small jeweler’s or eyeglass screwdriver
to move the small tab toward the center of the remote, while
using your index fingernail or screwdriver to pull down gently on
the slot to the right of the tab. The battery compartment will slide
out.
3. Place the battery, positive (+) side up, in the battery tray.
4. Slide battery compartment back into the remote until you hear a
click.
The remote control is ready for operation.
Do not use a knife or other sharp object to open the battery compartment;
they will scratch the remote control finish.
Notes
Replace batteries when remote control function becomes intermittent.
Remove batteries if the remote control is not used for a long time. Battery
leakage can damage the remote control.
The DVD Standard remote control provides power, standard and
advanced disc functions, and setup and programming functions. A
description of the remote control keys for the DVD Standard follows.
Remote Control
Functions
38 Power Key
POWER
Use this key to switch the DVD Standard from the stand-by to the
operational mode. The blue power LED on the front panel illuminates.
39 Audio Key
ADVANCED DISC
FUNCTIONS
Use this key to cycle between the languages available on the disc
soundtrack. Options appear in the upper left corner of the video dis-
play. The last item scrolled to is automatically selected.
20
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Functions, continued
ADVANCED DISC
40 Subtitle Key
FUNCTIONS, continued
Use this key to activate subtitles on the currently playing disc.
Options for turning subtitles off and on, and the subtitle languages
available are displayed on the screen. Use the directional buttons or
keys to navigate and press the enter button or key to set the selection.
Note
Using this key does not change the subtitle options selected in the setup
menu.
41 Angle Key
Use this key to select alternate camera angles, when they are avail-
able on the disc.
42 Title Key
Use this key to access the title menu.
Note
For most discs, when you press the title key, the title menu for the current
title will appear. Many video discs have only one title: when you press the
title key, the disc menu will appear. If the title key does not function with the
disc you are playing, use the menu button or key instead.
MENU AND SETUP
FUNCTIONS
43 Menu Key
Use this key to access the beginning disc menu. Use directional but-
tons or keys to move through the menu and press enter to select the
desired menu item. Playback will pause when you enter the menu.
44 Setup Key
Use this key to access the DVD Standard setup menu. The setup
menu allows you to customize your DVD Standard configuration, dis-
play, and audio, and to set parental controls. Press the setup button
again to exit the setup menu. See System Setup, on page 31, for
information on customizing the DVD Standard.
45 Directional Keys
Use these keys to navigate disc menus.
46 Enter Key
Use this key to accept selected menu or program items.
47 Ret(urn) Key
Use this key to navigate interactive menus.
Krell DVD Standard
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Functions, continued
DISC FUNCTIONS
48 Repeat Key
Use this key to activate the repeat options, which include:
ALL REPEAT
(repeats entire disc)
TITLE REPEAT
CHAPTER REPEAT
REPEAT OFF
(repeats chapters in current title)
(repeats currently playing chapter)
(clears repeat function)
The repeat option appears briefly in the upper left corner of the video
display. The last item scrolled to is automatically selected. To clear
the repeat command:
— select REPEAT OFF from the repeat menu
— press the stop button or key twice
— press the clear button or key
— press the power button or key to place the component in the
stand-by mode.
49 Disp(lay) Key
Use this key to display title and chapter numbers and to scroll
through time modes. The current title and chapter number will appear
on the top left corner of the video display. The display options, shown
in the right corner, are:
1. Press once: elapsed time of chapter.
2. Press again: remaining time of chapter.
3. Press again: elapsed time of title.
4. Press again: remaining time of title.
5. Press again: display feature turns off.
22
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Functions, continued
DISC FUNCTIONS, continued
50 Track Forward Key
Use this key to move forward one chapter or track. The upper left
corner of the video display shows SEARCH and the currently playing
chapter or track number.
51 Track Back Key
Use this key to move back one chapter or track. The upper left cor-
ner of the video display shows SEARCH and the currently playing
chapter or track number.
52 Search Forward Key
Use this key to access the two fast-forward playback modes when in
play mode. Press once: the right corner of the video display shows
FF1. Press again: the screen shows screen shows FF2. Use the
search forward button to switch between the slower (FF1) and faster
(FF2) modes. Press the play button or key to resume normal play-
back. Also use this key for single step forward when in the pause
mode.
53 Search Back Key
Use this key to access the two fast-reverse playback modes when in
play mode. Press once: the right corner of the video display shows
FR1. Press again: the screen shows FR2. Use the search back but-
ton to switch between the slower (FR1) and faster (FR2) modes.
Press the play button or key to resume normal playback. Also use
this key for single step forward when in the pause mode.
54 Pause Key
Use this key to pause disc playback. The video display indicates
PAUSE in top right corner. To resume playback, press the pause or
play button or key.
55 Play Key
Use this key to begin or resume disc playback.
56 Open/Close Key
Use this key to open and close the disc transport.
57 Stop Key
Use this key to stop disc playback. The video display shows the fol-
lowing message:
WHEN PLAY IS PUSHED, THE PLAYER WILL PLAY FROM WHERE YOU
STOPPED. TO START FROM THE BEGINNING, PRESS STOP AGAIN.
Krell DVD Standard
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Functions, continued
DISC FUNCTIONS, continued
58 Numeric Keys
Use the numeric keys to select a disc track. During playback, when
you press a numeric key, the screen displays TITLE/CHAPTER SEARCH.
Enter the number of the desired chapter or title. Use the clear key to
change an entry. When the desired chapter or title is displayed, press
enter. Playback resumes at the selected chapter or title.
Note
This feature will not let you enter any chapter or title not available on the
disc.
PROGRAMMING
FUNCTIONS
59 A-B Key
Use this key to create a playback loop between two predetermined
points within a single track or sequential tracks. See How to Create
an A-B Loop, on page 29.
60 Clr (Clear) Key
Use this key to clear the last numeric key entry, to clear an A-B loop
setting, or to clear an entry on the program grid.
61 Prog(ram) Key
Use this key to program a playback sequence. See How to Write a
Program, on page 27, for more information.
24
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the DVD Standard
to Your System
USING BALANCED
CONNECTIONS
Krell recommends using balanced interconnect cables. Balanced
interconnect cables not only can minimize sonic loss but are also
less sensitive to induced noise, especially with installations using
long cables. Balanced connections have 6 dB more gain than single-
ended connections. When level matching is critical, keep this gain
value in mind.
This section provides information about connecting your DVD
Standard to other components in your system. The DVD Standard is
equipped with a variety of connection options, for ease of integration
into your home theater system.
Connection
Steps
Follow these steps to connect the DVD Standard to your system.
1. Make sure all power sources and components are off before
connecting inputs and outputs.
2. Neatly organize the wiring between the DVD Standard and all
system components. Separate AC wires from audio cables to
prevent hum or other unwanted noises from being introduced into
the system.
3. Connect the input of your video components to the appropriate
output of the DVD Standard. See Getting Started, on page 6, for
information on ensuring that your video monitor and settings are
compatible with the DVD Standard.
4. Connect the balanced or single-ended analog outputs.
5. Plug the AC power cord into the IEC connector (37) on the back
panel, then plug the AC power cord into the wall socket. The red
stand-by LED (3) on the front panel illuminates.
Krell DVD Standard
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your DVD Standard
This section provides information about operating the DVD Standard.
After the DVD Standard is connected to the video monitor and other
system components, it is ready for operation.
1. Insert the AC power cord into the IEC power connector (37) on
the DVD Standard. Insert the other end into the AC wall recepta-
cle. The red stand-by LED (3) illuminates.
On/Off/Stand-by
2. Press the power button (1) or key (38) The blue power LED (2)
on the front panel illuminates. The DVD Standard is in the opera-
tional mode. The disc transport is active.
3. To return to the stand-by mode, press the power button or power
key again. The red stand-by LED illuminates.
Note
Krell recommends leaving the DVD Standard in the stand-by mode when
not playing a disc.
The DVD Standard can play the following discs:
COMPATIBLE DISCS
DVD 12CM single- or double-sided, 1 or 2 layer
DVD 8CM single- or double-sided, 1 or 2 layer
Video CD 12CM single-sided
Video CD 8CM single-sided
CD-DA 12CM single-sided
CD-DA 8CM single-sided
CD-R 12CM single-sided
1. Press the open/close button (13) or key (56) to open the disc
transport (14).
How to Play
a Disc
2. Place the disc on the transport.
3. Press the open/close button or key again to close the disc
transport.
4. Playback begins from the first track.
5. Press the stop button (7) or key (57) to end disc playback.
Adjust the volume level through your system volume control.
Notes
See Front Panel Description, on page 11, and How to Write a Program,
on page 27, for more information on disc playback options.
26
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your DVD Standard, continued
At the bottom of the program screen is a box with directions for navi-
gating the program box.
How to Write a
Program
1. Press the program key (61). The video display shows a program
box with spaces to enter the title and chapter numbers for each
program track. The first program track is highlighted (yellow).
ALL CLEAR
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
:
:
:
:
:
:
:
:
:
:
:
No.
1
T , C
TITLE
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
—, —
—, —
—, —
—, —
—, —
—, —
—, —
—, —
—, —
—,—
--
1
2
3
4
5
6
7
8
9
2
3
4
ᮣ
5
ᮣ
ᮣ
ᮣ
6
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
7
8
ᮣ
ᮣ
ᮣ
9
10
→
→
CLEAR
ENTER
ꢀ
ᮡ ꢁ
ᮣ
→
PLAY
QUIT : PROGRAM
2. Use the ᮣ directional button (16) or key (45) to select the title(s)
and chapter(s) for the first program track. Use the clear key (60)
to erase a selection, or press the ᮡ directional button (16) or key
(45) and scroll to the top of the program box, to select ALL CLEAR.
3. Press the enter button (17) or key (46) to set the selection.
4. Use the directional buttons or keys and the enter button or key to
select additional program tracks.
Krell DVD Standard
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your DVD Standard, continued
How to Write a Program,
continued
5. When you press the ᮣ directional button or key, the title sub-
menu appears. Scroll down to 9 and press ᮣ again. The chapter
submenu appears (entries vary according to what is available on
the current disc).
ALL CLEAR
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
:
:
:
:
:
:
:
:
:
:
:
No.
1
T , C
TITLE
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
CHAPTER
—, —
—, —
—, —
—, —
—, —
—, —
—, —
—, —
—,—
--
1
2
3
4
5
6
7
8
9
ALL
1
2
3
2
4
ᮣ
5
ᮣ
ᮣ
ᮣ
ᮣ
6
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
7
8
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
9
10
→
→
CLEAR
ENTER
ꢀ
ᮡ ꢁ
ᮣ
→
PLAY
QUIT : PROGRAM
6. When all program tracks are selected, press the play button (8)
or key (55) to begin playback of the program sequence.
28
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Your DVD Standard, continued
1. When you see or hear the selection that you want as the begin-
How to Create an
A-B Loop
ning of the loop, press the A-B key (59) to insert the start posi-
tion. REPEAT A appears on the video display.
2. When you see or hear the selection you want as the end of the
loop, press the A-B key again to insert the finish position.
REPEAT A-B appears on the video display.
3. Playback of the loop begins automatically and continues until you
press the clear key (60). REPEAT OFF appears on the video display.
You can pause and resume play within an A-B loop the same as during
normal playback.
Note
Krell DVD Standard
29
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup Overview
This page outlines the System Setup Menu and briefly describes its
features. This easy to follow menu lets you customize your DVD
Standard for optimum operation. You can select from the following
options:
— Config(uration)
— Faroudja
— Audio
— Parental (Control)
The configuration menu lets you match your video monitor to the
DVD Standard, select different brightness and contrast standards,
and select languages for audio track, subtitles, and DVD menu. This
menu also lets you prepare your DVD Standard for a software
upgrade.
Config
The Faroudja display menu options allow you to customize your DVD
Standard video performance.
Faroudja
Audio
The audio menu lets you match the DVD Standard to your system’s
digital output capabilities, select audio output, and select the data
rate that is compatible with your system.
The parental control menu lets you set and change an access pass-
word, as well as set allowable viewing levels and standards, for con-
trol of what is played on the DVD Standard even if you are not pre-
sent.
Parental
30
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup
Access to the setup menu is available through the front panel setup
button or through the remote control.
The only system setup you need to complete before playing your
DVD Standard is configuring television type. See Getting Started,
on pages 6-9 for instructions. The other items in the setup menu are
optional and may be set up at your convenience. Krell encourages
you to use the setup menu to optimize the performance of the DVD
Standard with your system.
This section explains menu navigation and guides you through each
section of the system setup menu.
ACCESSING THE
SETUP MENU
1. Connect the DVD Standard to your video monitor; see Getting
Started, on pages 6-9.
2. Connect the AC power cord to the IEC power connector (37) on
the DVD Standard back panel and to the AC wall receptacle. The
red stand-by LED (3) illuminates.
3. Press the power button (1) or key (38). The blue power LED (2)
illuminates, indicating that the DVD Standard is in the operational
mode.
4. Press the setup button (19) or key (44). The SETUP MENU screen
appears.
Krell DVD Standard
31
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
NAVIGATING THE MENU
To navigate the setup menu, use the directional buttons (16) or keys
(45) and the enter button (17) or key (46). The directional buttons
and keys ᮤ, ᮡ, ᮣ, and ᮢ let you move around the menu screen and
highlight the desired selection (indicated by yellow). Use the enter
key to select the highlighted item. If at any time you wish to exit the
setup menu, press the setup button or key.
The menu has four sections: configuration, Faroudja, audio, and
parental. Menu content is described on the following pages.
At the bottom of each setup screen is a box with directions for navi-
gating the menu.
ᮤ ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
32
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
The configuration menu lets you match your video monitor to the
DVD Standard, select different brightness and contrast standards,
and select languages for audio track, subtitles, and DVD menu. This
menu also lets you prepare your DVD Standard for a software
upgrade.
Configuration
Menu
When you press the setup button or key, you see the following
screen, which shows the four setup options, plus the configuration
menu selections:
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ᮣ
ᮣ
ᮣ
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
FAROUDJA
AUDIO
ᮣ
ᮣ
ᮣ
16:9
TV MODE:
STANDARD
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
The CONFIG box is highlighted yellow.
Krell DVD Standard
33
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
Audio
This option lets you select the language of the DVD Standard audio
track, if the language is available on the disc you are playing. Press
the ᮣ button or key to highlight AUDIO, then press the enter button or
key. The audio submenu appears.
Set Up Menu
AUDIO:
ENGLISH ᮣ
ENGLISH
ENGLISH
NO
ORIGINAL
ENGLISH
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
JAPANESE
CHINESE
GERMAN
FRENCH
ITALIAN
FAROUDJA
AUDIO
16:9
TV MODE:
STANDARD
SPANISH
DUTCH
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
The currently selected item is highlighted yellow. Press the ᮢ button
or key to choose the preferred language, then press the enter button
or key.
34
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
Subtitle
This option lets you choose the language for subtitles, if the language
is available on the disc you are playing. Press the ᮢ button or key to
highlight SUBTITLE, then press the enter button or key. The subtitle
submenu appears.
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ORIGINAL
ENGLISH
ᮣ
CONFIG
ᮣ
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
JAPANESE
CHINESE
GERMAN
FRENCH
ITALIAN
FAROUDJA
AUDIO
16:9
TV MODE:
STANDARD
SPANISH
DUTCH
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
The currently selected option is highlighted yellow. Press the ᮢ but-
ton or key to choose the preferred language, then press the enter
button or key.
Krell DVD Standard
35
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
DVD Menu
This option lets you select the language of the DVD menus, if the
language is available on the disc. Press the ᮢ button or key to high-
light DVD MENU, then press the enter button or key. The DVD sub-
menu appears.
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ORIGINAL
ENGLISH
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
ᮣ
JAPANESE
CHINESE
GERMAN
FRENCH
ITALIAN
FAROUDJA
AUDIO
16:9
TV MODE:
STANDARD
SPANISH
DUTCH
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
The currently selected option is highlighted yellow. Press the ᮢ but-
ton or key to choose the preferred language, then press the enter
button or key.
36
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
Software Upgrade
This option lets you prepare the DVD Standard for a software
upgrade. Press the ᮢ button or key to highlight SW UPGRADE, then
press the enter button or key. The SW upgrade submenu appears.
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
FAROUDJA
AUDIO
ᮣ
YES
NO
16:9
TV MODE:
STANDARD
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
If you need to install an upgrade disc, press the ᮣ button or key to
select YES and press the enter button or key.
Krell DVD Standard
37
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
TV Type
This menu selection must be used to select the DVD television
aspect ratio that matches your video monitor. If you have a standard
size television screen, choose 4:3 LT (letterbox with a black box at
the top and bottom of the screen) or 4:3 PS (pan and scan, with the
picture extending to the screen margins). Choose 16:9 if you have a
wide-screen television. See Getting Started, on page 9. Press the ᮢ
button or key to highlight TV TYPE, then press the enter button or key.
The TV type submenu appears.
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
FAROUDJA
AUDIO
ᮣ
16:9
4:3 LT
4:3 PS
16:9
TV MODE:
STANDARD
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the television type, then press
the enter button or key.
For proper viewing, you must select the correct television format
before you begin playing a disc.
IMPORTANT
38
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
CONFIGURATION MENU,
continued
TV Mode
This option lets you modify the standard video outputs for different
brightness, contrast, and sharpness settings. Press the ᮢ button or
key to highlight TV MODE, then press the enter button or key. The TV
mode submenu appears.
Set Up Menu
AUDIO:
ENGLISH
ENGLISH
ENGLISH
NO
ᮣ
CONFIG
SUBTITLE:
DVDMENU:
SW UPGRADE:
TV TYPE:
STANDARD
CINEMA
FAROUDJA
AUDIO
16:9
ANIMATION
SPORTS
TV MODE:
STANDARD ᮣ
B and W
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred mode, then press
the enter button or key.
Krell DVD Standard
39
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
The Faroudja display setup options allow you to customize your
video display.
Faroudja Menu
Press the ᮤ and ᮢ buttons or keys to highlight FAROUDJA. The
Faroudja menu appears.
Set Up Menu
CONFIG
ᮣ
ᮣ
ᮣ
ᮣ
ᮣ
MOTION:
ADP
ON
ᮣ
FAROUDJA
AUDIO
FILM:
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
40
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Faroudja Menu, continued
Motion
This option lets you choose the motion compensation mode.
Adaptive (ADP) selects a method of combining progressive fields,
depending on their motion content. For no motion compensation,
set to OFF. Press the ᮣ button or key to highlight MOTION, then press
the enter button or key. The motion submenu appears.
Set Up Menu
CONFIG
ᮣ
MOTION:
ADP
ON
NONE
FULL
ADP
FAROUDJA ᮣ
AUDIO
FILM:
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred motion compensa-
tion option, then press the enter button or key.
Krell DVD Standard
41
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Faroudja Menu, continued
Film
This option lets you select the 3:2 pulldown algorithm. Press the ᮢ
button or key to highlight FILM, then press the enter button or key. The
film submenu appears.
Set Up Menu
CONFIG
MOTION:
ADP
ON
FAROUDJA ᮣ
AUDIO
ᮣ
FILM:
OFF
ON
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred film option, then
press the enter button or key.
42
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Faroudja Menu, continued
Enhancer
This option lets you set the level of edge enhancement and gain,
to make the video image sharper with a more defined edge. Press
the ᮢ button or key to highlight ENHANCER, then press the enter button
or key. The enhancer submenu appears.
Set Up Menu
OFF
LOW
CONFIG
0
MOTION:
ADP
ON
ᮣ
1
FAROUDJA
AUDIO
FILM:
2
ᮣ
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
3
4
5
PARENTAL
6
HIGH
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred enhancer option,
then press the enter button or key.
Krell DVD Standard
43
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Faroudja Menu, continued
Animation
This option lets you enable or disable chroma correction when the
video is from a computer-generated source. For animated DVDs,
set animation to ON. For standard DVDs, select OFF. Press the ᮢ
button or key to highlight ANIMATION, then press the enter button or
key. The animation submenu appears.
Set Up Menu
CONFIG
MOTION:
ADP
ON
ᮣ
FAROUDJA
AUDIO
FILM:
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
ᮣ
OFF
ON
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred animation option,
then press the enter button or key.
44
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Faroudja Menu, continued
Sync on G
This option lets you put sync on the green signal, for compatibility
with various monitors. If the signals are not correctly set, you will
not get a picture. Press the ᮢ button or key to highlight SYNC ON G,
then press the enter button or key. The sync on G submenu appears.
Set Up Menu
CONFIG
MOTION:
ADP
ON
ᮣ
FAROUDJA
AUDIO
FILM:
ENHANCER:
ANIMATION:
SYNC ON G:
OFF
OFF
OFF
ᮣ
OFF
ON
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred sync option, then
press the enter button or key.
Krell DVD Standard
45
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
This menu option allows you to match the DVD Standard to your sys-
tem’s capabilities, select audio output, set dynamic range control,
and choose the sample rate compatible with your system. Press the
ᮤ and ᮢ buttons or keys to highlight AUDIO. The audio screen
appears.
Audio Menu
Set Up Menu
CONFIG
FAROUDJA
ᮣ
ᮣ
ᮣ
DOWNMIX:
DIG OUT:
DRC:
STEREO
Dolby D/DTS
MAX
ᮣ
AUDIO
PARENTAL
96K->48K:
ENABLE ᮣ
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
46
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Audio Menu, continued
Downmix
Use this option to select either 2 channel stereo or surround mode to
match the DVD Standard to your system’s surround decoding capa-
bilities. Select stereo mode if your system does not have a surround
decoder. Press the ᮣ button or key to highlight DOWNMIX, then press
the enter button or key. The downmix submenu appears.
Set Up Menu
CONFIG
FAROUDJA
ᮣ
DOWNMIX:
DIG OUT:
DRC:
STEREO
Dolby D/DTS
MAX
STEREO
ᮣ
AUDIO
SURROUND
PARENTAL
96K->48K:
ENABLE
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred downmix option,
then press the enter button or key.
The chart below shows how downmix and digital out settings affect
analog and digital outputs.
Digital Out
+
Downmix
=
Analog Output
Digital Output
Dolby D/DTS
Stereo
Stereo
Dolby D/DTS
Dolby D/DTS
Surround
Dolby Surround
compatible
Dolby D/DTS
PCM
PCM
Stereo
Stereo
Stereo
Surround
Dolby Surround
compatible
Dolby Surround
compatible
Krell DVD Standard
47
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Audio Menu, continued
Digital Out
This option allows you to select either PCM or Dolby Digital/DTS
encoded audio output. Select Dolby D/DTS if the digital output is con-
nected to a digital decoder that can decode Dolby Digital or DTS
material. Press the ᮢ button or key to highlight DIGITAL OUT, then
press the enter button or key. The digital out submenu appears.
Set Up Menu
CONFIG
FAROUDJA
DOWNMIX:
DIG OUT:
DRC:
STEREO
Dolby D/DTS
MAX
ᮣ
AUDIO
ᮣ
Dolby D/DTS
PCM
PARENTAL
96K->48K:
ENABLE
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred digital output
option, then press the enter button or key.
48
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Audio Menu, continued
DRC
This option lets you set the dynamic range control (compression
level) of audio output for Dolby Digital material only. Choose max-
imum (max) for full range. Choose standard (std) to keep the
range at the same setting as in the Dolby Digital disc. For a high
degree of compression at low listening levels, choose minimum
(min). Press the ᮢ button or key to highlight DRC, then press the
enter button or key. The DRC submenu appears.
Set Up Menu
CONFIG
FAROUDJA
DOWNMIX:
DIG OUT:
DRC:
STEREO
Dolby D/DTS
MAX
ᮣ
AUDIO
ᮣ
MAX
STD
MIN
PARENTAL
96K->48K:
ENABLE
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred DRC option, then
press the enter button or key.
Krell DVD Standard
49
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
Audio Menu, continued
96K-48K
This option allows the DVD Standard to convert 96K sample rate
data to 48K, the sample rate compatible for most systems. Select
disable if your system is capable of playing 96K input signals without
conversion (see the owner’s manual for other system components).
Press the ᮢ button or key to highlight 96K-48K, then press the enter
button or key. The 96K-48K submenu appears.
Set Up Menu
CONFIG
FAROUDJA
DOWNMIX:
DIGITAL OUT:
DRC:
STEREO
DD/DTS
MAX
ᮣ
AUDIO
PARENTAL
96K->48K:
ENABLE ᮣ
DISABLE
ENABLE
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred sample rate
option, then press the enter button or key.
50
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
The parental menu options allow you to set a parental security pass-
word, set allowable viewing levels, and change your password.
Parental Menu
Press the ᮤ and ᮢ buttons or keys to highlight the parental menu.
The password screen appears.
Set Up Menu
CONFIG
Enter password.
Enter a number in
4 digits, then
press ENTER.
FAROUDJA
AUDIO
ꢀ ꢀ ꢀ ꢀ
ᮣ
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press enter to highlight the screen.
Press the numeric keys to enter your four-digit password. A dash
appears in each box as you enter a number.
Press enter. The confirmation screen appears:
Set Up Menu
CONFIG
To confirm, enter
password again,
the press ENTER
FAROUDJA
AUDIO
ꢀ ꢀ ꢀ ꢀ
ᮣ
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Krell DVD Standard
51
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
PARENTAL MENU, continued
After you correctly re-enter your password, press the enter button or
key. The parental menu appears.
Set Up Menu
CONFIG
FAROUDJA
AUDIO
ᮣ
LEVEL:
OFF
ᮣ
PARENTAL
STANDARD:
USA ᮣ
ᮣ
CHANGE PASSWORD
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
To reset your password, from the stand-by mode, press and hold the
stop button, then press the power button.
IF YOU FORGET
YOUR PASSWORD
52
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
PARENTAL MENU, continued
Level
The viewing level menu allows you to set the allowable viewing level
of discs played. For example, level 1 allows viewing of the equivalent
of G rating without entering a password. Any video disc with a higher
rating (2-8) requires override. See the video disc package for viewing
level numbers and their rating equivalents.
Press the enter button or key. The level submenu appears.
Set Up Menu
CONFIG
8
7
FAROUDJA
AUDIO
6
5
4
3
2
ᮣ
LEVEL:
OFF
USA
ᮣ
PARENTAL
1
STANDARD:
OFF
CHANGE PASSWORD
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press the ᮢ button or key to choose the preferred access level, then
press the enter button or key.
Krell DVD Standard
53
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup, continued
PARENTAL MENU, continued
If anyone attemps to play a disc that exceeds the viewing level, the
following message appears:
USER PARENTAL LOCK IS SET. NOT ABLE TO PLAY.
If you wish to play the disc, you must reset the viewing level.
Press the setup button or key, enter your password, then select
viewing level. Set the viewing level to off or to a higher setting
such as 8.
54
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup and Configuration, continued
PARENTAL MENU, continued
Standard
The standard menu allows you to select the rating standard for
movies. Currently the DVD Standard has one setting, USA. Press
the ᮤ and ᮢ buttons or keys to highlight the standard menu.
Set Up Menu
CONFIG
FAROUDJA
AUDIO
LEVEL:
OFF
ᮣ
PARENTAL
USA
STANDARD:
USA ᮣ
CHANGE PASSWORD
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Krell DVD Standard
55
Download from Www.Somanuals.com. All Manuals Search And Download.
System Setup and Configuration, continued
Change Password
PARENTAL MENU, continued
The change password menu allows you to change your original
password. You may wish to change your password regularly.
Press the ᮤ and ᮢ buttons or keys to highlight the change password
menu.
Set Up Menu
CONFIG
CHANGE PASSWORD
FAROUDJA
AUDIO
ꢀ ꢀ ꢀ ꢀ
ᮣ
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Press enter to select this option. You return to the password screen.
Set Up Menu
CONFIG
Enter a number in
4 digits, then
press ENTER.
FAROUDJA
AUDIO
ꢀ ꢀ ꢀ ꢀ
ᮣ
PARENTAL
ᮤ
ᮡ ᮢ ᮣ → ENTER
QUIT : SET UP
Enter and confirm your new password.
Press the setup button or key to exit the setup menu.
56
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
To register your product
for warranty benefits, please
complete and return the
Warranty Registration Card
enclosed in the shipping box
within 15 days of
This Krell product has a limited warranty of five years for parts and labor on circuitry and three
years for parts and labor on all mechanical components. Should this product fail to perform at
any time during the warranty, Krell will repair it at no cost to the owner, except as set forth in
this warranty.
The warranty does not apply to damage caused by acts of God or nature.
The warranty on this page shall be in lieu of any other warranty, expressed or implied, includ-
ing, but not limited to, any implied warranty of merchantability or fitness for a particular purpose.
There are no warranties which exceed beyond those described in this document. If this product
does not perform as warranted herein, the owner’s sole remedy shall be repair. In no event will
Krell be liable for incidental or consequential damages arising from purchase, use, or inability to
use this product, even if Krell has been advised of the possibility of such damages.
purchase. Thank you.
Proof of purchase in the form of a bill of sale or receipted invoice substantiating that the unit is
within the warranty period must be presented to obtain warranty service. The warranty begins
on the date of the original retail purchase, as noted on the bill of sale or receipted invoice from
an authorized Krell dealer or distributor. Previously owned equipment, when re-purchased from
an authorized Krell dealer or distributor, has the balance of the original warranty, based on the
original date of manufacture.
The warranty for Krell products is valid only in the country to which they were originally shipped,
through the authorized Krell distributor for that country, and at the factory. There may be restric-
tions on or changes to Krell’s warranty because of regulations within a specific country. Please
check with your distributor for a complete understanding of the warranty in your country.
If a unit is serviced by a distributor who did not import the unit, there may be a charge for ser-
vice, even if the product is within the warranty period.
Freight to the factory is your responsibility. Return freight within the United States (U.S.A.) is
included in the warranty. If you have purchased your Krell product outside the U.S.A. and wish
to have it serviced at the factory, all freight and associated charges to the factory are your
responsibility.
Krell will pay return freight to the U.S.A.-based freight forwarder of your choice. Freight and
other charges to ship the unit from the freight forwarder to you are also your responsibility.
Krell is not responsible for any damage incurred in transit. Krell will file claims for damages as
necessary for units damaged in transit to the factory. You are responsible for filing claims for
shipping damages during the return shipment.
Krell does not supply replacement parts and/or products to the owner of the unit. Replacement
parts and/or products will be furnished only to the distributor performing service on this unit on
an exchange basis only; any parts and/or products returned to Krell for exchange become the
property of Krell.
No expressed or implied warranty is made for any Krell product damaged by accident, abuse,
misuse, natural or personal disaster, or unauthorized modification.
Any unauthorized voltage conversion, disassembly, component replacement, perfora-
tion of chassis, updates, or modifications performed to the unit will void the warranty.
The operating voltage of this unit is determined by the factory and can only be changed by an
authorized Krell distributor or at the factory. The voltage for this product in the U.S.A. cannot be
changed until six months from the original purchase date.
In the event that Krell receives a product for warranty service that has been modified in any
way without Krell authorization, all warranties on that product will be void. The product will be
returned to original factory layout specifications at the owner’s expense before it is repaired. All
repairs required after the product has been returned to original factory specifications will be
charged to the customer, at current parts and labor rates.
All operational features, functions, and specifications and policies are subject to change without
notification.
Krell DVD Standard
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Return Authorization
Procedure
HOW TO EXPEDITE
SERVICE
If you believe there is a problem with your component, please con-
tact your dealer, distributor, or the Krell factory to discuss the problem
before you return the component for repair. To expedite service, you
may wish to complete and e-mail the Service Request Form in the
Service section of our website at:
To contact the Krell Service Department:
TEL
203-799-9954
Monday-Friday, 9:00 AM to 5:00 PM EST
203-799-9796
FAX
E-MAIL
HOW TO RETURN
A PRODUCT
To return a product to Krell, please follow this procedure so that we
may serve you better:
1. Obtain a Return Authorization Number (R/A number) and ship-
ping address from the Krell Service Department.
2. Insure and accept all liability for loss or damage to the product
during shipment to the Krell factory and ensure all freight (ship-
ping) charges are prepaid.
The product may also be hand delivered if arrangements with the
Service Department have been made in advance. Proof of purchase
will be required for warranty validation at the time of hand delivery.
IMPORTANT
Use the original packaging to ensure the safe transit of the product to
the factory, dealer, or distributor. Krell may, at its discretion, return a
product in new packaging and bill the owner for such packaging if the
product received by Krell was boxed in nonstandard packaging or if
the original packaging was so damaged that it was unusable. If Krell
determines that new packaging is required, the owner will be notified
before the product is returned.
HOW TO PURCHASE
ADDITIONAL PACKING
To purchase additional packaging, please contact your authorized
Krell dealer, distributor, or the Krell Service Department for assis-
tance.
SERIAL NUMBER
Your DVD Standard product serial number is:
58
Krell DVD Standard
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Krell Industries, Inc.
DVD Standard
45 Connair Road
v 01.1
Orange, CT 06477-3650 USA
TEL 203-799-9954, FAX 203-891-2028
E-MAIL [email protected]
Download from Www.Somanuals.com. All Manuals Search And Download.
|