Dear Customer,
Thank you for purchasing this digital
video camera. Before use, please
read the safety information and
precautions contained in the pages
3 – 5 to ensure safe use of this
product.
ENGLISH
DIGITAL VIDEO CAMERA
GETTING STARTED
7
GR-D750U
RECORDING & PLAYBACK
16
ADVANCED FEATURES
22
REFERENCES
34
TERMS
40
For Customer Use:
Enter below the Model No. and
Serial No. which is located on the
bottom of the camcorder. Retain
this information for future reference.
Model No.
Serial No.
To deactivate the demonstration,
set “DEMO MODE” to “OFF”.
(੬ pg. 22, 24)
INSTRUCTIONS
LYT1654-001B
Download from Www.Somanuals.com. All Manuals Search And Download.
EN
3
Read This First!
● Before recording important video, be sure to ● Remember that this camcorder is intended
make a trial recording.
for private consumer use only.
Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for
personal enjoyment, it is strongly recommended
that you obtain permission beforehand.)
● DO NOT leave the unit
Play back your trial recording to make sure the
video and audio have been recorded properly.
● We recommend cleaning your video heads
before use.
If you haven’t used
your camcorder for
awhile, the heads may
- in place of over 50°C (122°F)
be dirty. We
recommend
- in place where humidity is extremely low
(below 35%) or extremely high (80%).
- in direct sunlight.
- in a closed car in summer.
- near a heater.
● The LCD monitor is made with high-
precision technology. However, black spots
or bright spots of light (red, green or blue)
may appear constantly on the LCD monitor.
These spots are not recorded on the tape.
This is not due to any defect of the unit.
(Effective dots: more than 99.99%)
periodically cleaning
the video heads with a
cleaning cassette
(optional).
● Be sure to store your cassette tapes and
camcorder in the proper environment.
Video heads can become dirty more easily if
your cassette tapes and camcorder are stored
in a dusty area. Cassette tapes should be
removed from the camcorder and stored in
cassette cases. Store the camcorder in a bag or ● Do not leave the battery pack attached when
other container.
the camcorder is not in use and check the
unit regularly whether it is working or not.
● Use SP (Standard) mode for important video
recordings.
LP (Long Play) mode lets you record 50% more
video than SP (Standard) mode, but you may
experience mosaic-like noise during playback
depending on the tape characteristics and the
usage environment.
So, for important recordings, we recommend
using SP mode.
● For safety and reliability.
It is recommended only genuine JVC batteries
and accessories are used in this camcorder.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF808U/VF815U/VF823U battery packs.
Using generic non-JVC batteries can cause
damage to the internal charging circuitry.
● Remember that this camcorder is not
compatible with other digital video formats.
● It is recommended that you use JVC brand
cassette tapes.
Also read “CAUTIONS” on pages 36 – 38.
● Microsoft® and Windows® are either registered
trademarks or trademarks of Microsoft
Corporation in the United States and/or other
countries.
● Macintosh is a registered trademark of Apple
Computer, Inc.
● QuickTime is a registered trademark of Apple
Computer, Inc.
Your camcorder is compatible with all brands of
commercially available cassette tapes
complying with the MiniDV standard, but JVC
brand cassette tapes are designed and
optimized to maximize the performance of your
camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
EN
SAFETY PRECAUTIONS
When the equipment is installed in a cabinet or on a
shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or
more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted
candles, should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules
or laws governing the disposal of these batteries
must be followed strictly.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
The apparatus shall not be exposed to dripping
or splashing.
Do not use this equipment in a bathroom or
places with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines,
flower vases, potted plants, cups etc.) on top of
this unit.
WARNING:TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)
CAUTIONS:
● This camcorder is designed to be used with
NTSC-type color television signals. It cannot
be used for playback with a television of a
different standard. However, live recording and
LCD monitor/viewfinder playback are possible
anywhere.
● This product includes patented and other
proprietary technology and will operate only
with JVC Data Battery. Use the JVC
BN-VF808U/VF815U/VF823U battery packs
and, to recharge them or to supply power to
the camcorder from an AC outlet, use the
provided multi-voltage AC Adapter. (An
appropriate conversion adapter may be
necessary to accommodate different designs
of AC outlets in different countries.)
Do not point the lens or the viewfinder directly
into the sun. This can cause eye injuries, as well
as lead to the malfunctioning of internal circuitry.
There is also a risk of fire or electric shock.
CAUTION!
The following notes concern possible physical
damage to the camcorder and to the user.
When carrying, be sure to always securely attach
and use the provided strap. Carrying or holding
the camcorder by the viewfinder and/or the LCD
monitor can result in dropping the unit, or in a
malfunction.
Take care not to get your finger caught in the
cassette holder cover. Do not let children operate
the camcorder, as they are particularly
susceptible to this type of injury.
This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material -
special handling may apply.
perchlorate
Do not use a tripod on unsteady or unlevel
surfaces. It could tip over, causing serious
damage to the camcorder.
CAUTION!
NOTES:
Connecting cables (Audio/Video, S-Video, etc.) to
the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will
cause the camcorder to fall, resulting in damage.
● The rating plate (serial number plate) and
safety caution are on the bottom and/or the
back of the main unit.
● The rating information and safety caution of the
AC Adapter are on its upper and lower sides.
Download from Www.Somanuals.com. All Manuals Search And Download.
USER MAINTENANCE
EN
5
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
Cleaning The Camcorder
Before cleaning, turn off the camcorder and
remove the battery pack and AC Adapter.
4. Follow all instructions.
To clean the exterior
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
Wipe gently with a soft cloth. Put the cloth in
diluted mild soap and wring it well to wipe off
heavy dirt. Then wipe again with a dry cloth.
To clean the LCD monitor
Wipe gently with a soft cloth. Be careful not to
damage the monitor. Close the LCD monitor.
To clean the lens
Blow it with a blower brush, then wipe gently
with lens cleaning paper.
9. Only use attachments/accessories specified
by the manufacturer.
10. Use only with the
To clean the viewfinder lens
Remove dust from the viewfinder using a
blower brush.
cart, stand, tripod,
bracket, or table
specified by the
manufacturer, or
sold with the
apparatus.When a
cart is used, use
caution when
NOTES:
● Avoid using strong cleaning agents such as
benzine or alcohol.
● Cleaning should be done only after the battery
pack has been removed or other power units
have been disconnected.
● Mold may form if the lens is left dirty.
● When using a cleaner or chemically treated
cloth refer to the cautions of each product.
● To clean the viewfinder, please consult your
nearest JVC dealer.
moving the cart/
apparatus combination to avoid injury from tip-
over.
11. Unplug this apparatus during lightning storms
or when unused for long periods of time.
12. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
USE CLEANING CASSETTE
Appears if dirt is detected on the heads during
recording. Use an optional cleaning cassette
(੬ pg. 3).
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
GETTING STARTED
6
EN
7
ADVANCED FEATURES
22
Regarding This Manual .................................7
Provided Accessories....................................7
Index..............................................................8
Grip Adjustment...........................................11
Power ..........................................................12
Language Settings.......................................13
Date/Time Settings......................................14
Viewfinder Adjustment.................................14
Brightness Adjustment Of The Display........14
Tripod Mounting...........................................14
Loading/Unloading A Cassette....................15
16:9 Wide Mode ..........................................15
MENUS FOR DETAILED ADJUSTMENT ..............22
Changing The Menu Settings...................... 22
Recording Menus........................................ 23
Playback Menus.......................................... 25
FEATURES FOR RECORDING ...........................26
LED Light .................................................... 26
Snapshot (Record Still Image On Tape) ..... 26
Manual Focus.............................................. 27
Exposure Control ........................................ 27
Iris Lock....................................................... 28
Backlight Compensation ............................. 28
Spot Exposure Control................................ 28
White Balance Adjustment.......................... 29
Manual White Balance Adjustment ............. 29
Wipe Or Fader Effects................................. 30
Program AE, Effects And Shutter Effects.... 30
EDITING ........................................................31
Dubbing To A VCR...................................... 31
Dubbing To Or From A Video Unit Equipped
With A DV Connector (Digital Dubbing).. 32
Connection To A Personal Computer ......... 33
RECORDING & PLAYBACK
16
VIDEO RECORDING ........................................16
Basic Recording ..........................................16
Tape Remaining Time.............................16
Quick Review...........................................16
Zooming...................................................17
Journalistic Shooting ...............................17
Interface Shooting ...................................17
Time Code...............................................18
Recording From The Middle Of A Tape...18
Auto/Manual Mode ..................................18
VIDEO PLAYBACK ..........................................19
Normal Playback .........................................19
Still Playback...........................................19
Variable Shuttle Search...........................20
Blank Search...........................................20
Playback Snapshot..................................20
Connections To A TV Or VCR.....................21
REFERENCES
34
TROUBLESHOOTING.......................................34
CAUTIONS.....................................................36
SPECIFICATIONS ............................................39
TERMS ..........................................................40
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
7
Regarding This Manual
Provided Accessories
Control Lever
LCD Monitor
OR
AC Adapter AP-V14U or AP-V18U
OR
Audio/Video Cable
(ø3.5 mini-plug to RCA plug)
Control lever
BatteryPack
BN-VF808U
There are two kinds of operation using the control
lever: moving the lever towards up/down/left/right,
or pressing down the lever.
They are described and illustrated as shown
below.
1) Move the control lever up/down/left/right
(3/4/1/2) to select:
Select
Shoulder
Lens Cap
(੬ pg. 11)
Strap
(੬ pg. 11)
NOTES:
Operation
To select
● In order to maintain optimum performance of the
camcorder, provided cables may be equipped
with one or more core filter. If a cable has only
one core filter, the end that is closest to the filter
should be connected to the camcorder.
● Make sure to use the provided cables for
connections. Do not use any other cables.
Move the control lever up.
3
4
6
7
FOCUS
Move the control lever
down.
Move the control lever
right.
LIGHT
2
1
¡
1
Move the control lever left.
QUICK
REVIEW
2) Press down the control lever to select SET:
SET
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
8
EN
Index
78
u(&
31
24
25
26
27
30
9 "! 21
22
4 5
6
#
29 28
$
18
19
1 3 2
%
23
20
How to open the LCD monitor
Pull on the end A of the LCD monitor.
NOTES:
● The image will not appear
simultaneously on the LCD monitor and
the viewfinder. When the viewfinder is
pulled out while the LCD monitor is
opened, you can select which one to
use. Set “PRIORITY” to the desired
mode in SYSTEM Menu. (੬ pg. 24)
● Colored bright spots may appear all over
the LCD monitor or the viewfinder.
However, this is not a malfunction.
The LCD monitor can rotate 270°.
Power-linked operation
When the power switch is set to “REC”, you can
also turn the camcorder on/off by opening/
closing the LCD monitor or pulling out/pushing in
the viewfinder.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
9
Controls
Indicators
11 : Left/Rewind (1) (੬ pg. 19)/
Quick Review [QUICK REVIEW] (੬ pg. 16)
2: Right/Fast-Forward (¡) (੬ pg. 19)/
LED Light [LIGHT] (੬ pg. 26)
POWER/CHARGE Lamp (੬ pg. 12)
Other Parts
LCD Monitor (੬ pg. 8)
Viewfinder (੬ pg. 14)
Battery Pack Mount (੬ pg. 12)
Shoulder Strap Eyelet (੬ pg. 11)
Grip Strap (੬ pg. 11)
Speaker (੬ pg. 19)
Lens
3 : Up/Play/Pause (6) (੬ pg. 19)/
Manual Focus [FOCUS] (੬ pg. 27)
4 : Down/Stop (7) (੬ pg. 19)/
Backlight Compensation [ ] (੬ pg. 28)/
Spot Exposure (੬ pg. 28)
Press down : SET
216:9 Wide Screen Button [16:9] (੬ pg. 15)
Blank Search [BLANK] (੬ pg. 20)
3Menu Button [MENU] (੬ pg. 22)
4Data Battery Button [DATA] (੬ pg. 13)
5Auto Button [AUTO] (੬ pg. 18)
6Diopter Adjustment Control (੬ pg. 14)
7Snapshot Button [SNAPSHOT] (੬ pg. 26)
8Power Zoom Lever [T/W] (੬ pg. 17)
Speaker Volume Control [VOL. +, –]
(੬ pg. 19)
LED Light (੬ pg. 26)
Camera Sensor
(Be careful not to cover this area, a sensor
necessary for shooting is built-in here.)
Stereo Microphone
Stud Hole (੬ pg. 14)
Tripod Mounting Socket (੬ pg. 14)
Cassette Holder Cover (੬ pg. 15)
Connector Cover
9Recording Start/Stop Button [START/STOP]
(੬ pg. 16)
!Power Switch [REC, PLAY, OFF]
"Lock Button
#Battery Release Button [BATT.] (੬ pg. 12)
$Cassette Open/Eject Switch [OPEN/EJECT]
(੬ pg. 15)
Power Switch Position
REC:
To perform recording on the tape.
OFF:
To switch off the camcorder.
PLAY:
Connectors
To play back a recording on the tape.
%Digital Video Connector [DV IN/OUT]
(i.LINK*) (੬ pg. 32, 33)
*
i.LINK refers to the IEEE1394-1995 industry
specification and extensions thereof. The
logo is used for products compliant with the
i.LINK standard.
The connectors are located beneath the
covers.
&Audio/Video Output Connector [AV]
(੬ pg. 21)
(DC Input Connector [DC] (੬ pg. 12)
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
10
~Selected Wipe/Fader Effect Indicator
(੬ pg. 30)
LCD Monitor/Viewfinder
Indications
+Wind Cut Indicator (੬ pg. 23)
,Tape Running Indicator
(Rotates while tape is running.)
-Date/Time (੬ pg. 24)
.Manual Focus Adjustment Indicator
(੬ pg. 27)
During Video Recording
%
&
"
#
$
1
2
3
4
5
6
7
8
9
– – –min
REC
M
LP
10
x
16:9
/Time Code (੬ pg. 24)
(
)
~
+
3
During Video Playback
W
H
1
2
3 4
5 6
,
SOUND 12 BIT
15:55
LP
x3
11:13 AM
12B I T / M I X
L
DEC.6.2007
!
/
.
-
BLANK SEARCH
PUSH "STOP" BUTTON
TO CANCEL
1Battery Remaining Power Indicator
2Operation Mode (੬ pg. 18)
: Auto Mode
: Manual Mode
3LED Light Indicator (੬ pg. 26)
VOLUME
11
.
:
6
13 AM
200
20 : 21 : 25
DE C
.
7
4
: Night-Alive Indicator (੬ pg. 30)
: Gain Up Mode (੬ pg. 23)
9
7
8
5Shutter Speed (੬ pg. 31)
6White Balance Indicator (੬ pg. 29)
7Selected Effect Indicator (੬ pg. 31)
8Selected Program AE Indicator (੬ pg. 30)
9SOUND 12BIT/16BIT: Sound Mode
Indicator (੬ pg. 24) (Appears for approx. 5
seconds after turning on the camcorder.)
!Digital Image Stabilizer (“DIS”) (੬ pg. 23)
1Battery Remaining Power Indicator
2Sound L/R Indicator (੬ pg. 25)
3Blank Search Indicator (੬ pg. 20)
4Tape Speed (SP/LP) (੬ pg. 25)
(only LP indicator is displayed)
5Variable Search Speed Indicator: x-10, x-3,
x3 and x10 (੬ pg. 20)
63: Playback
(only
indicator is displayed)
¡: Fast-Forward/Shuttle Search
1: Rewind/Shuttle Search
8: Pause
"Approximate Zoom Ratio (੬ pg. 17)
#Zoom Indicator (੬ pg. 17)
$Selected Wide Mode Indicator (੬ pg. 15)
(only 16:9 indicator is displayed)
%Recording Speed Mode (SP/LP) (੬ pg. 24)
(only LP indicator is displayed)
&Tape Remaining Time (੬ pg. 16)
(REC: (Appears during recording.)
(੬ pg. 16)
7Date/Time (੬ pg. 25)
8VOLUME: Volume Level Indicator
(੬ pg. 19)
9Time Code (੬ pg. 25)
PHOTO: (Appears when taking Snapshot.)
(੬ pg. 20, 26)
: Spot Exposure Control Indicator
(੬ pg. 28)
: Backlight Compensation Indicator
(੬ pg. 28)
)
: Exposure Adjustment Indicator
(੬ pg. 27)
: Iris Lock Indicator (੬ pg. 28)
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
11
How To Attach The Lens Cap
Grip Adjustment
To protect the lens, attach
the provided lens cap to the
camcorder as shown in the
illustration.
Open the pad and make grip adjustments.
● Before making the adjustment, remove any
security tags that may be attached to the
velcro.
NOTE:
To confirm the lens cap is on
correctly make sure the cap is
flush to the camcorder.
Place here during
shooting.
How To Attach The Shoulder Strap
1 Peel off the pad
and thread the end
of the strap
through the eyelet.
Eyelet
2 Thread the
Strap Guide
strap through the
Buckle
buckle, adjust its
length, and use the
strap guide to fix it
in place.
3 Position the
buckle near the
eyelet and reattach
the pad.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
12
NOTES:
Power
Charging The Battery Pack
● If the protective cap is attached to the battery
pack, remove it first.
● During charging, the camcorder cannot be
operated.
POWER/CHARGE Lamp
● Charging is not possible if the wrong type of
battery is used.
● When charging the battery pack for the first time
or after a long storage period, the POWER/
CHARGE lamp may not light. In this case,
remove the battery pack from the camcorder,
then try charging again.
Battery pack
mount
Arrow
2
● If a fully charged battery pack is attached to the
unit, POWER/CHARGE lamp will blink for
approx. 10 seconds before it turns off.
● If the battery operation time remains extremely
short even after having been fully charged, the
battery is worn out and needs to be replaced.
Please purchase a new one.
1
Battery
pack
BATT.
Power switch
To DC connector
● Since the AC Adapter processes electricity
internally, it becomes warm during use. Be sure
to use it only in well-ventilated areas.
● After 5 minutes have elapsed in Record-
Standby mode with the cassette inserted and no
operation is performed, the camcorder will
automatically turn off its power supplied from the
AC adapter. In this case, the battery charge
starts if the battery is attached to the camcorder.
● Please do not pull or bend the AC adapter plug
and cable. This may damage the AC adapter.
Lock
Button
AC Adapter
To AC outlet
1 Set the Power Switch to “OFF”.
2 With the arrow on the battery pack pointing
upward, push the battery pack slightly against
the battery pack mount 1.
About Batteries
DANGER! Do not attempt to take the batteries
apart, or expose them to flame or excessive
heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its
terminals to come in contact with metals, as
this can result in a short circuit and possibly
start a fire.
3 Slide up the battery pack until it locks in
place 2.
4 Plug the AC Adapter into an AC outlet.
5 Connect the AC Adapter to the camcorder.
● The POWER/CHARGE lamp on the camcorder
blinks to indicate charging has started.
● When the POWER/CHARGE lamp goes out,
charging is finished. Unplug the AC Adapter
from the AC outlet. Disconnect the AC Adapter
from the camcorder.
To restore the accuracy of the battery
power indicator
If the battery power indication differs from the
actual operating time, fully charge the battery,
and then run it down. However this method
may not work if the battery was used for a long
period of time under extremely high/low
temperature condition or charged too many
times.
To detach the battery pack
Slide the battery pack downward while
pressing BATT. to detach it.
Battery pack
BN-VF808U*
Charging time
Approx. 1 hr. 30 min.
Approx. 2 hrs. 40 min.
Approx. 3 hrs. 50 min.
BN-VF815U
BN-VF823U
* Provided
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
● If “COMMUNICATION ERROR” appears
EN
13
Using The Battery Pack
Perform steps 2 – 3 in “Charging The Battery
Pack” (੬ pg. 12).
instead of the battery status even though you
tried to press DATA several times, there may
be a problem with your battery. In such a
case, consult your nearest JVC dealer.
Maximum continuous recording time
Using AC Power
Perform step 4 – 5 in “Charging The Battery
Pack” (੬ pg. 12).
LCD monitor
Battery pack
Viewfinder on
on
BN-VF808U*
BN-VF815U
BN-VF823U
* Provided
NOTES:
1 hr. 50 min.
3 hrs. 40 min.
5 hrs. 30 min.
2 hrs. 15 min.
4 hrs. 30 min.
6 hrs. 45 min.
NOTE:
The provided AC Adapter features automatic
voltage selection in the AC range from 110 V to
240 V.
INFORMATION:
● Recording time is reduced significantly under
the following conditions:
• Zoom or Record-Standby mode is engaged
The following explanations in this manual
supposes the use of LCD monitor in your
operation. If you want to use the viewfinder,
close the LCD monitor and pull out the
viewfinder fully.
repeatedly.
• The LCD monitor is used repeatedly.
• The playback mode is engaged repeatedly.
• The LED Light is used.
● Before extended use, it is recommended that
you prepare enough battery packs to cover
3 times the planned shooting time.
Language Settings
The language on the display can be changed.
(੬ pg. 24)
ATTENTION:
Select
Before detaching the power source, make sure
that the camcorder’s power is turned off. Failure to
do so can result in a camcorder malfunction.
LANGUAGE
ENGLISH
Data Battery System
You can check the remaining battery power
and the recordable time.
SET
When the battery is attached, press DATA.
1 Open the LCD monitor fully.
BATTERY CONDITION
2 Set the Power Switch to “REC” or “PLAY”
while pressing down the Lock Button located
on the switch.
LEVEL
100%
MAX TIME
LCD
110min
● If set to “REC”, the recording mode should be
set to “ ” (੬ pg. 18).
50
0
FINDER
135min
3 Press MENU.
● When the Power Switch is set to “OFF”, it is
displayed for approx. 3 seconds if the button
is pressed and released quickly, and for
approx. 15 seconds if the button is pressed
and hold for several seconds.
● When the Power Switch is set to “PLAY” or
“REC”, press DATA again to return to the
normal screen.
4 Select “SYSTEM”, press SET or 2.
5 Select “LANGUAGE”, press SET or 2.
6 Select the desired language, press SET or
2.
7 Press MENU.
Press 1whenever you want to return to the
previous menu screen.
● Data battery status cannot be displayed
during playback or while recording is in
progress.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
14
Date/Time Settings
Brightness Adjustment Of The
Display
Select
CLOCK ADJ.
YEAR. MONTH. DATE 24
h
Select
2007 JAN 03
14 : 10
BRIGHT
0
SET
The date/time is recorded onto the tape at all
times, but its display can be turned on or off.
(੬ pg. 24, 25)
Perform steps 1 – 3 in “Language Settings”
(੬ pg. 13).
SET
Perform steps 1 – 3 in “Language Settings”
(੬ pg. 13).
● To adjust the brightness of the viewfinder,
pull out the viewfinder fully and set
“PRIORITY” to “FINDER” (੬ pg. 24).
1 Select “DISPLAY”, press SET or 2.
2 Select “CLOCK ADJ.”, press SET or 2.
1 Select “DISPLAY”, press SET or 2.
2 Select “BRIGHT”, press SET or 2.
3 Select the desired date display format,
press SET or 2.
● Repeat this step to input time display format
(Select from “24h” or “12h”), month, date, year,
hour and minutes.
3 Select the appropriate brightness, press
SET or 2.
4 Press MENU.
Press 1whenever you want to return to the
previous menu screen.
4 Press MENU.
Press 1whenever you want to return to the
previous menu screen/setting.
Tripod Mounting
Viewfinder Adjustment
To attach the
1 Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch.
camcorder to a tripod,
align the direction stud
and screw to the
mounting socket and
stud hole on the
2 Make sure the LCD monitor is closed and
locked. Pull out the viewfinder fully.
camcorder. Then
tighten the screw
clockwise.
● Some tripods are not
equipped with studs.
3 Turn the Diopter Adjustment Control until
the indications in the viewfinder are clearly
focused.
Example:
Diopter Adjustment Control
CAUTION:
When retracting the viewfinder, take care not to
pinch your fingers.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
EN
15
Loading/Unloading A Cassette
• Appears if a tape is loaded while the Power
Switch is set to “REC”.
• Blinks when no tape is loaded.
The camcorder needs to be powered up to
load or eject a cassette.
TAPE!
PUSH
Appears if a tape is not loaded when the
Cassette
holder
cover
Recording Start/Stop Button is pressed while the
Power Switch is set to “REC”.
CHECK TAPE’S ERASE PROTECTION TAB
Appears when the erase protection tab is set to
“SAVE” while the Power Switch is set to “REC”.
16:9 Wide Mode
You can record videos at 4:3 size and 16:9
size. By default, the camera is set to record
videos at the 16:9 size.
Erase
OPEN/
EJECT
protection
tab
Cassette holder
Make sure the window
side is facing out.
1 Slide and hold OPEN/EJECT in the
direction of the arrow, then pull the cassette
holder cover open until it locks. The cassette
holder opens automatically.
● Do not touch internal components.
2 Insert or remove a tape and press “PUSH”
to close the cassette holder.
● Be sure to press only the section labeled
“PUSH” to close the cassette holder; touching
other parts may cause your finger to get caught
in the cassette holder, resulting in injury or
product damage.
● Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.
● When the battery pack’s charge is low, you may
not be able to close the cassette holder cover.
Do not apply force. Replace the battery pack
with a fully charged one or use AC power before
continuing.
16:9
1 Set the Power Switch to “REC”.
2 Each press 16:9 switches the screen size.
On the LCD monitor:
16 : 9
4 : 3
4 : 3
3 Close the cassette holder cover firmly until
On the viewfinder:
it locks into place.
NOTES:
● If you wait a few seconds and the cassette
holder does not open, close the cassette holder
cover and try again. If the cassette holder still
does not open, turn the camcorder off then on
again.
16 : 9
● If the tape does not load properly, open the
cassette holder cover fully and remove the
cassette. A few minutes later, insert it again.
● When the camcorder is suddenly moved from a
cold place to a warm environment, wait a short
time before opening the cassette holder cover.
NOTE:
If you record videos in 16:9 size, the image may
appear to be slightly vertically stretched when
playing back on TV with the 4:3 screen.
(੬ pg. 24, 25)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO RECORDING
EN
16
Tape Remaining Time
Approximate tape
Basic Recording
remaining time appears on
the display. “– – – min”
means the camcorder is
calculating the remaining
NOTE:
Before continuing, perform the procedures listed
below:
● Power (੬ pg. 12)
● Loading A Cassette (੬ pg. 15)
● Remove the lens cap. (੬ pg. 11)
● Open the LCD monitor fully.
● Select videos at 4:3 size or 16:9 (wide) size.
(੬ pg. 15)
time. When the remaining time reaches
2 minutes, the indication starts blinking.
● The time required to calculate and display the
remaining tape length, and the accuracy of the
calculation, may vary according to the type of
tape used.
Zoom Lever
Quick Review
Enables to check the end of the last recording.
1) Press QUICK REVIEW during
the Recording-Standby mode.
2) Tape is rewound for about
Lock Button
several seconds and played back
automatically, then pauses in the
Recording-Standby mode for the next shot.
● Distortion may occur at start of playback. This is
normal.
Recording Start/Stop
Button
1 Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch.
● Slide the Power Zoom lever repeatedly to
change the sound to on/off.
2 Press START/STOP button to start
recording. “REC” appears on the display while
recording is in progress. To stop recording,
press START/STOP again.
Approximate recording time
Recording mode
Tape
SP
LP
45 min.
30 min.
60 min.
80 min.
30 min.
60 min.
80 min.
90 min.
120 min.
NOTES:
● If the Record-Standby mode continues for
5 minutes and no operation is performed, the
camcorder’s power shuts off automatically. To
turn the camcorder on again, push back and pull
out the viewfinder again or close and re-open
the LCD monitor.
● When a blank portion is left between recorded
scenes on the tape, the time code is interrupted
and errors may occur when editing the tape. To
avoid this, refer to “Recording From The Middle
Of A Tape” (੬ pg. 18).
● To record in LP (Long Play) mode, ੬ pg. 24.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO RECORDING
EN
17
Zooming
Interface Shooting
While recording
The person you shoot
can view himself/
Zoom out
Zoom in
herself in the LCD
monitor, and you can
even shoot yourself
while viewing your
own image in the
LCD monitor.
1) Open the LCD
W: Wide angle
● You can zoom in up to 34X by using the optical
zoom.
T: Telephoto
● Zoom magnification over 34X is done through
digital image processing, and is therefore called
digital zoom. Digital zooming is possible up to
800X. Set (ZOOM) to [68X] or [800X].
(੬ pg. 23)
monitor and tilt it
upward to 180° so
that it faces forward.
Then, pull out the
viewfinder fully.
2) Point the lens
Optical zoom (up to 34X)
toward the subject (yourself when self-
recording) and start recording.
● During Interface Shooting, the monitor image
appears inverted as it would when viewing a
mirror. However, the actual recorded image
does not appear inverted.
Digital zoom (up to 800X)
● If the Quick Review (੬ pg. 16) is executed
during the interface shooting, the LCD monitor
will be turned off. In such a case, check the
playback picture in the viewfinder.
● To check the playback picture in the LCD
monitor, close the viewfinder.
NOTES:
● Macro shooting is possible as close as approx. 5
cm (2") to the subject when the zoom lever is set
all the way to W.
● When you zoom into a subject close to the lens,
the camera may automatically zoom out
depending on the distance to the subject. In this
case, set “TELE MACRO” to “ON”. (੬ pg. 23)
Journalistic Shooting
In some situations,
different shooting
angles may provide
more dramatic
results. Hold the
camcorder in the
desired position and
tilt the LCD monitor
in the most
convenient direction.
It can rotate 270°
(90° downward, 180°
upward).
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO RECORDING
EN
18
Time Code
Recording From The Middle Of A Tape
During recording, a time code is recorded on
1) Play back a tape or use Blank Search
the tape.This code is to confirm the location of (੬ pg. 20) to find the spot at which you want to
the recorded scene on the tape during
playback.
start recording, then engage the Still Playback
mode. (੬ pg. 19)
2) Set the Power Switch to “REC” while
pressing down the Lock Button located on the
switch, then start recording.
Display
Minutes
Auto/Manual Mode
Seconds
Press AUTO button repeatedly to switch to
auto/manual recording mode. When manual
mode is selected, the indicator“ ” appears on
the LCD monitor.
Frames*
(30 frames =
12 : 34 : 24
1 second)
* Frames are not displayed during recording.
If recording starts from a blank portion, the
time code begins counting from “00:00:00”
(minute:second:frame). If recording starts from
the end of a previously recorded scene, the
time code continues from the last time code
number. If during recording a blank portion is
left partway through the tape, the time code is
interrupted. When recording is resumed, the
time code starts counting up again from
“00:00:00”. This means the camcorder may
record the same time codes as those existing
in a previously recorded scene.To prevent this,
perform Recording From The Middle Of A Tape
(੬ pg. 18) in the following cases;
Auto Mode :
You can record using no special effects or
manual adjustments.
Manual Mode :
Manual recording is possible by setting various
functions.
AUTO
MANUAL
● When shooting again after playing back a
recorded tape.
● When power shuts off during shooting.
● When a tape is removed and re-inserted during
shooting.
● When shooting using a partially recorded tape.
● When shooting on a blank portion located
partway through the tape.
● When shooting again after shooting a scene
then opening/closing the cassette holder cover.
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time
code indication does not move smoothly.
● The time code is displayed only when “TIME
CODE” is set to “ON”. (੬ pg. 24)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO PLAYBACK
EN
19
NOTES:
Normal Playback
● The playback picture can be viewed in the LCD
monitor, viewfinder or on a connected TV.
(੬ pg. 21)
VOL. +/–
Lock Button
BLANK
● If Stop mode continues for 5 minutes when
power is supplied from a battery, the camcorder
shuts off automatically.To turn the camcorder on
again, push back and pull out the viewfinder
again or close and re-open the LCD monitor.
● When a cable is connected to the AV connector,
the sound is not heard from the speaker.
6
¡
Power
Switch
1
MENU
HDV
7
Speaker
Appears when pictures recorded in the HDV
format are detected. The pictures in the HDV
format cannot be played back with this
camcorder.
1 Load a cassette. (੬ pg. 15)
2 Set the Power Switch to “PLAY” while
pressing down the Lock Button located on the
switch.
Still Playback
Pauses during video playback.
1) Press 6 during playback.
2) To resume normal playback, press 6
again.
● If still playback continues for more than about
3 minutes, the camcorder’s Stop mode is
automatically engaged.
SET
● The above screen (referring to the control lever
(੬ pg. 7)) will be displayed for approx. 3
seconds on the LCD Monitor.
Operation
6
7
¡
To select
Move the control lever up.
Move the control lever down.
Move the control lever right.
Move the control lever left.
1
3 To start playback, press 6.
4 To stop playback, press 7.
● During Stop mode, press 1 to rewind, or ¡
to fast-forward the tape.
● Press SET to display the guide operation
screen.
To control the speaker volume
Slide the Power Zoom Lever (VOL. +/–)
towards “+” to turn up the volume, or towards
“–” to turn down the volume.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO PLAYBACK
EN
20
Variable Shuttle Search
Blank Search
Allows variable-speed search in either
direction during video playback.
Helps you find where you should start
recording in the middle of a tape to avoid time
1) During playback, press ¡ once or twice for code interruption. (੬ pg. 18)
forward search, or 1 once or twice for
1 Perform steps 1 – 2 in “Normal Playback”
reverse search.
(੬ pg. 19).
1
¡
2 Press BLANK.
x-10
x-3
x3
x10
● The “BLANK SEARCH” indication appears and
the camcorder automatically starts reverse or
forward search, then stops at the spot which is
about 3 seconds of tape before the beginning of
the detected blank portion.
2) To resume normal playback, press 6.
● During playback, press and hold ¡ or 1.
The search continues as long as you hold the
button. Once you release the button, normal
playback resumes.
● A slight mosaic effect appears on the display
during Shuttle Search. This is not a malfunction.
● To cancel Blank Search, press 7 or BLANK.
NOTES:
● Before starting Blank Search, if the current
position is at a blank portion, the camcorder
searches in the reverse direction. If the current
position is at a recorded portion, the camcorder
searches in the forward direction.
ATTENTION:
During Shuttle Search,
parts of the picture may not
be clearly visible,
● If the beginning or end of the tape is reached
during Blank Search, the camcorder stops
automatically.
particularly on the left side
of the screen.
● A blank portion which is shorter than 5 seconds
of tape may not be detected.
● The detected blank portion may be located
between recorded scenes. Before you start
recording, make sure there is no recorded
scene after the blank portion.
During Shuttle Search,
parts of the picture may not
be clearly visible across
the screen.
Playback Snapshot
This camcorder allows you to take snapshots
during video playback.
Press SNAPSHOT.
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO PLAYBACK
EN
21
1 Make sure all units are turned off.
Connections To A TV Or VCR
2 Connect the camcorder to a TV or VCR as
shown in the illustration.
If using a VCR, go to step 3.
If not, go to step 4.
3 Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.
4 Turn on the camcorder, the VCR and the TV.
To AV
connector
5 Set the VCR to its AUX input mode, and set
the TV to its VIDEO mode.
or
6 Start playback on the camcorder.
(੬ pg. 19)
● Please set “16:9 OUTPUT” of Playback Menus
so that the image may suit your TV (16:9 TV or
4:3 TV). (੬ pg. 24, 25)
Audio/Video cable
(provided)
To choose whether or not the following
displays appear on the connected TV
● Date/Time
Set “DATE/TIME” to “ON” or “OFF” (੬ pg. 25).
● Time Code
Set “TIME CODE” to “ON” or “OFF” (੬ pg. 25).
● Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/TV”
(੬ pg. 25).
TV
VCR
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
● To monitor the picture and sound from the
camcorder without inserting a tape or memory
card, set the camcorder’s Power Switch
to“REC”, then set your TV to the appropriate
input mode.
1Yellow to VIDEO IN (Connect when your TV/
VCR has only A/V input connectors.)
2Red to AUDIO R IN*
3White to AUDIO L IN*
* Not required for watching still images only.
● Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT
EN
22
4 Select the desired function, press SET or 2.
Changing The Menu Settings
This camcorder is equipped with an easy-to-
use, on-screen menu system that simplifies
many of the more detailed camcorder settings.
(੬ pg. 22 – 25)
The selected function menu appears.
Example: FUNCTION menu.
Current Setting
FUNCTION
Power Switch
WN
W
IPE/FADER
OFF
OFF
PROGRAM AE
EFFECT
EXPOSURE
0
AUTO
OFF
W
.BALANCE
SHUTTER
EXIT
Lock
Button
5 Select the desired selection, press SET or
2.
Select
Example: WIPE/FADER menu.
WIPE/FADER
OFF
OFF
WH
WHITE
BLACK
SLIDE
SET
MENU
BK
1 For Video Recording Menu:
● Set the Power Switch to “REC” while
pressing down the Lock Button located on
the switch.
SCROLL
● Set the recording mode to “ ”. (੬ pg. 18)
6 Select the desired setting, press SET or 2.
Selection is completed.
For Video Playback Menu:
● Set the Power Switch to “PLAY” while
pressing down the Lock Button located on
the switch.
7 Press MENU. The Menu Screen closes.
● Press 1whenever you want to cancel or return
to the previous menu screen.
● Repeat the procedure if you wish to set other
function menus.
2 Open the LCD monitor fully. (੬ pg. 8)
3 Press MENU. The Menu Screen appears.
Screen for Video
Recording Menu
Screen for Video
Playback Menu
FUNCTION
CAMERA
VTR
VTR
DISPLAY
SYSTEM
DISPLAY
SYSTEM
EXIT
EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT
EN
23
In the following pages, [ ] refers to Factory
preset settings.
TELE MACRO
[OFF]: Disables the function.
ON: When the distance to the subject is less
than 1 m (3.3 ft), set “TELE MACRO” to “ON”.
You can shoot a subject as large as possible at
a distance of approx. 40 cm (1.4 ft).
Recording Menus
FUNCTION
Depending on the zoom position, the lens may go
The following menu settings can be changed
only when the Power Switch is set to “REC”.
out of focus.
DIS
WIPE/FADER
OFF
: Disables the function. (DIS disable
icon appears.)
(੬ pg. 30), “Wipe or Fader Effects”
[ON]: To compensate for unstable images
caused by camera-shake, particularly at high
magnification.
PROGRAM AE
(੬ pg. 30), “Program AE, Effects And Shutter
Effects”
NOTES:
● Accurate stabilization may not be possible if
hand shake is excessive, or depending on the
shooting condition.
EFFECT
(੬ pg. 30, 31), “Program AE, Effects And
Shutter Effects”
● Switch off this mode when recording with the
camcorder on a tripod.
● DIS cannot be activated when “NIGHT” in
“PROGRAM AE”, or “STROBE” in “EFFECT” is
selected or when LIGHT is set to on, or when
SNAPSHOT is pressed.
EXPOSURE
(੬ pg. 27), “Exposure Control”
W. BALANCE
(੬ pg. 29), “White Balance Adjustment”
GAIN UP
SHUTTER
OFF: Allows you to shoot dark scenes with no
picture brightness adjustment.
[AGC]: The overall appearance may be grainy,
but the image is bright.
(੬ pg. 30, 31), “Program AE, Effects And
Shutter Effects”
CAMERA
AUTO
: The shutter speed is
The following menu settings can be changed
only when the Power Switch is set to “REC”.
automatically adjusted. Shooting a subject in
low or poor lighting at slow shutter speed
provides a brighter image than in the AGC
mode, but the subject’s movements are not
smooth or natural. The overall appearance
may be grainy. While the shutter speed is
ZOOM
[34X]: When set to “34X” while using digital
zoom, the zoom magnification will reset to 34X
since digital zoom will be disengaged.
68X: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 34X (the optical
zoom limit), to a maximum of 68X digital
magnification.
being automatically adjusted, “
displayed.
” is
WIND CUT
[OFF]: Disengages the function.
ON
: Helps cut down on noise created by
800X: Allows you to use the Digital Zoom. By
digitally processing and magnifying images,
zooming is possible from 34X (the optical
zoom limit), to a maximum of 800X digital
magnification.
wind. The “
of the sound will change. This is normal.
” indicator appears. The quality
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT
EN
24
VTR
BRIGHT
੬ pg. 14, “Brightness Adjustment Of The
Display”
REC MODE
[SP]*: To record in the SP (Standard Play)
mode
LP: Long Play—more economical, providing
1.5 times the recording time.
SYSTEM
The “SYSTEM” functions which are set when
the Power Switch is set to “REC” are also
applied when the Power Switch is set to
“PLAY”.
* SP indicator does not appear on the screen.
NOTES:
● If the recording mode is switched, the playback
picture will be blurred at the switching point.
● During playback of a tape recorded on another
camcorder, blocks of noise may appear or there
may be momentary pauses in the sound.
LANGUAGE
[ENGLISH] / FRANCAIS / ESPAÑOL /
PORTUGUÊS
The language setting can be changed.
(੬ pg. 13)
SOUND MODE
MELODY
[12BIT]: Enables video recording of stereo
sound on four separate channels. (Equivalent
to the 32 kHz mode of previous models)
16BIT: Enables video recording of stereo
sound on two separate channels. (Equivalent
to the 48 kHz mode of previous models)
OFF: Even though not heard while shooting,
shutter sound is recorded on the tape.
[ON]: A melody sounds when any operation is
performed. It also activates the shutter sound
effect.
PRIORITY
DISPLAY
[LCD]: The image is displayed on the LCD
monitor when the viewfinder is pulled out while
the LCD monitor is opened.
FINDER: The image is displayed in the
viewfinder when the viewfinder is pulled out
while the LCD monitor is opened.
The “DISPLAY” settings (except “CLOCK
ADJ.”, “16:9 OUTPUT” and “BRIGHT”) are
effective only for shooting.
ON SCREEN
LCD: Keeps the camcorder’s display (except
the date, time and time code) from appearing
on the connected TV screen.
[LCD/TV]: Makes the camcorder’s display
appear on screen when the camcorder is
connected to a TV.
DEMO MODE
OFF: Automatic demonstration will not take
place.
[ON]: Demonstrates certain functions such as
Wipe/Fader and Effects, etc., and can be used
to confirm how these functions operate.
Demonstration starts in the following cases:
● When the Menu Screen is closed after “DEMO
MODE” is turned “ON”.
DATE/TIME
[OFF]: The date/time does not appear.
ON: The date/time is always displayed.
● With “DEMO MODE” set to “ON”, if there is no
operation for about 3 minutes after the Power
Switch is set to “REC”.
CLOCK ADJ.
੬ pg. 14, “Date/Time Settings”
● Performing any operation during the
demonstration stops the demonstration
temporarily. If no operation is performed for
more than 3 minutes after that, the
demonstration will resume.
TIME CODE
[OFF]: Time code is not displayed.
ON: Time code is displayed on the camcorder
and on the connected TV. Frame numbers are
not displayed during recording. (੬ pg. 18)
NOTES:
● If a cassette is in the camcorder, the
demonstration cannot be turned on.
● “DEMO MODE” remains “ON” even if the
camcorder power is turned off.
16:9 OUTPUT
To enable your tv to display images in 16:9
wide mode, set the tv screen size correctly.
4:3 TV: For TV with an aspect ratio of 4:3.
[16:9 TV]: For TV with an aspect ratio of 16:9.
Download from Www.Somanuals.com. All Manuals Search And Download.
MENUS FOR DETAILED ADJUSTMENT
EN
25
DISPLAY
CAM RESET
[CANCEL]: Does not reset all settings to the
factory-preset.
EXECUTE: Resets all settings to the factory-
preset.
Each setting (except “OFF” in “ON SCREEN”,
“DATE/TIME” and “TIME CODE”) is linked with
“DISPLAY”, which appears when the Power
Switch is set to “REC”.
The parameters (except “OFF” in “ON
SCREEN” setting) are the same as in the
description on ੬ pg. 24.
Playback Menus
VTR
ON SCREEN
When set to “OFF”, the camcorder’s display
disappears.
OFF / [LCD] / LCD/TV
The settings below are effective only for video
playback except “REC MODE”. The
parameters (except “SOUND L/R” and
“NARRATION” settings) are the same as in the
description on page 25.
DATE/TIME
[OFF] / ON
CLOCK ADJ.
SOUND L/R and NARRATION
During tape playback, the camcorder detects
the sound mode in which the recording was
made, and plays the sound back. Select the
sound to accompany your playback picture.
੬ pg. 14, “Date/Time Settings”
TIME CODE [OFF] / ON
੬ pg. 18, “Time Code”
16:9 OUTPUT
4:3 TV / [16:9 TV]
REC MODE
[SP]* / LP
੬ pg. 24, “16:9 OUTPUT”
Allows you to set the video recording mode
(SP or LP) depending on your preference. It is
recommended you use “REC MODE” in
VIDEO Menu when using this camcorder as a
recorder during dubbing. (੬ pg. 31, 32)
* SP indicator does not appear on the screen.
BRIGHT
੬ pg. 14, “Brightness Adjustment Of The
Display”
SYSTEM
NARRATION
Each setting (except “DEMO MODE”) is linked
with “SYSTEM”, which appears when the
Power Switch is set to “REC”.
Although it is not possible to perform audio
dubbing with this camcorder, you can hear
sound from an audio-dubbed tape during
playback using this function.
[OFF]: Original sound is output on both “L” and
“R” channels in stereo.
The parameters are the same as in the
description on page 24.
ON: Dubbed sound is output on both “L” and
“R” channels in stereo.
MIX: Original and dubbed sounds are
combined and output in stereo on both “L” and
“R” channels.
SOUND L/R
[STEREO
]: Sound is output on both “L” and
“R” channels in stereo.
SOUND L : Sound from the “L” channel is
output.
SOUND R : Sound from the “R” channel is
output.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EN
26
LED Light
LED Light can be used to
brighten the subject in the dark
place during video recording.
Snapshot (Record Still Image On
Tape)
This feature lets you record still images that
look like photographs onto a tape.
1 Set the Power Switch to “REC”.
LIGHT
2 Press SNAPSHOT.
LED Light
● The “PHOTO” indication appears and a still image
will be recorded for approx. 5 seconds, then the
camcorder re-enters the Record-Standby mode.
● You can perform Snapshot also during
recording. A still image will be recorded for
approx. 5 seconds, then the normal recording
resumes.
1 Press LIGHT repeatedly to change the
setting.
The light is on always. (
appears.)
The light turns on automatically
when dark. (
● If the image taken by snapshot is too dark or too
appears.)
bright, select
(੬ pg. 28) or “SPOTLIGHT”
(੬ pg. 30).
Turns off the light.
Motor Drive Mode
2 Press the Recording Start/Stop Button to
start video recording or SNAPSHOT to shoot a
still image.
Keeping SNAPSHOT pressed in step 2
provides an effect similar to serial photography.
(Interval between still images: approx. 1
second)
NOTES:
● Be careful not to point the LED Light directly to
eyes.
● If the light does not reach the subject when the
LED Light setting is “ON”, the Night-Alive
function will be activated, and makes it possible
to shoot the subject brighter.
● Since subjects are shot at a reduced shutter
speed when the LED Light setting is “ON”, they
will appear slightly blurred.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EN
27
Manual Focus
The camcorder’s Full Range AF system offers
continuous shooting ability from close-up (as
close as approx. 5 cm (2") to the subject) to
infinity.
However, correct focus may not be obtained
depending on the shooting condition. In this
case, use the manual focus mode.
Exposure Control
Manual exposure control is recommended in
the following situations:
● When shooting using reverse lighting or when
the background is too bright.
● When shooting on a reflective natural
background such as at the beach or when
skiing.
● When the background is overly dark or the
subject is bright.
1 Set the Power Switch to “REC”.
Select
FOCUS
1
2
EXPOSURE
0
SET
SET
1 Open the LCD monitor fully.
Manual focus indicator
2 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 18)
3 Set the recording mode to “ ”. (੬ pg. 18)
4 Press MENU.
3 Press FOCUS. The manual focus indicator
appears.
5 Select “FUNCTION”, press SET or 2.
6 Select “EXPOSURE”, press SET or 2.
4 Press 1or 2to focus on a subject.
● When the focus level cannot be adjusted any
further or closer, “ ” or “ ” will blink.
7 Select the appropriate exposure, press SET
5 Press SET. Focus adjustment is complete.
or 2.
● To brighten the image, press 3. To darken the
image, press 4. (maximum +/-6)
To reset to Auto Focus
Press FOCUS twice.
8 Press MENU.
Manual focus is recommended in
situations listed below.
● When two subjects overlap in the same scene.
● When illumination is low.*
● When the subject has no contrast (difference in
brightness and darkness), such as a flat, one-
color wall, or a clear, blue sky.*
● When a dark object is barely visible in the LCD
monitor or the viewfinder.*
● When the scene contains minute patterns or
identical patterns that are regularly repeated.
● When the scene is affected by sunbeams or
light reflecting off the surface of a body of water.
● When shooting a scene with a high-contrast
background.
NOTES:
● If the adjustment does not cause any visible
change in brightness, set “GAIN UP” to “AUTO”.
(੬ pg. 22, 23)
● You cannot use the manual exposure control at
the same time when “PROGRAM AE” is set to
“SPOTLIGHT” or “SNOW” (੬ pg. 30), or with
the backlight compensation.
* The following low-contrast warnings appear
blinking:
,
,
and
.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EN
28
Iris Lock
Spot Exposure Control
Selection of a spot metering area enables
more precise exposure compensation.
Like the pupil of the human eye, the iris
contracts in well-lit environments to keep too
much light from entering, and dilates in dim
environments to allow in more light.
Use this function in the following situations:
● When shooting a moving subject.
● When the distance to the subject changes (so
its size in the LCD monitor or the viewfinder
changes), such as when the subject is backing
away.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 18)
3 Press
twice so that the Spot Exposure
Control indicator “
” appears.
● A spot metering area frame appears at the
center of the LCD monitor/viewfinder.
4 Press SET.
● When shooting on a reflective natural
background such as at the beach or when
skiing.
● When shooting objects under a spotlight.
● When zooming.
● Spot Exposure Control is engaged.
● Exposure is adjusted to make the brightness of
the selected area most appropriate.
To lock the iris
1 Perform steps 1 - 6 in “Exposure Control”
(੬ pg. 27)
After step 3, press and hold SET over 2
seconds. The “ ” indication appears and the
iris is locked.
2 Adjust zoom so that the subject fills the
LCD monitor or the viewfinder, then press and
To cancel Spot Exposure Control
hold SET or 2for over 2 seconds. The “
”
Press
once so that the “
” indicator
indication appears.
disappears.
3 Press SET or 2. The iris is locked.
4 Press MENU.
NOTES:
● Depending on the shooting location and
condition, optimum result may not be attained.
● “STROBE” in “EFFECT” cannot be used with
Spot Exposure Control.
Backlight Compensation
Backlight compensation brightens the subject
quickly.
With simple operation, backlight compensation
feature brightens the dark subject portion by
increasing the exposure.
1 Set the Power Switch to
“REC”.
SET
2 Set the recording mode to
“
”. (੬ pg. 18)
3 Press
so that the
Backlight Compensation
indicator “ ” appears.
To cancel Backlight Compensation
Press
twice so that the “ ” indicator
disappears.
NOTE:
Using Backlight Compensation may cause the
light around the subject to become too bright and
the subject to become white.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EN
29
White Balance Adjustment
The white balance refers to the correctness of
color reproduction under various lighting. If the
white balance is correct, all other colors will be
accurately reproduced.
The white balance is usually adjusted
automatically. However, more advanced
camcorder operators control this function
manually to achieve a more professional color/
tint reproduction.
Manual White Balance
Adjustment
Adjust the white
balance manually
when shooting under
various types of
lighting.
1 Set the Power
White paper
Switch to “REC”.
To change the setting
Set “W. BALANCE” to the desired mode.
(੬ pg. 23)
● The selected mode indicator except “AUTO”
appears.
2 Set the recording mode to “ ”. (੬ pg. 18)
3 Hold a sheet of plain white paper in front of
the subject. Adjust zoom or position yourself
so that the white paper fills the screen.
4 Select “MWB” in “W. BALANCE” menu
(੬ pg. 23), then press and hold SET or 2until
begins blinking.
[AUTO]: White balance is adjusted
automatically.
MWB: Adjust the white balance
manually when shooting under various types
of lighting. (੬ “Manual White Balance
Adjustment”, pg. 29)
● When the setting is completed,
stops
blinking.
5 Press SET or 2to engage the setting.
6 Press MENU.The Menu Screen closes and
FINE: Outdoors on a sunny day.
CLOUD: Outdoors on a cloudy day.
HALOGEN: A video light or similar type
the Manual White Balance indicator
displayed.
is
of lighting is used.
NOTES:
● In step 3, it may be difficult to focus on the white
paper. In such a case, adjust focus manually.
(੬ pg. 27)
● Because the color temperature is different
depending on the light source, use this function
for a more natural result.
● Once you adjust white balance manually, the
setting is retained even if the power is turned off
or the battery removed.
● White Balance cannot be activated
simultaneously with “TWILIGHT” in “PROGRAM
AE” (੬ pg. 30).
● White Balance cannot be activated if the
“SEPIA” or “MONOTONE” mode is activated.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EN
30
Wipe Or Fader Effects
These effects let you make pro-style scene
transitions. Use them to spice up the transition
from one scene to the next.
Wipe or Fader works when video recording is
started or stopped.
Program AE, Effects And Shutter
Effects
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 18)
3 Set “EFFECT”, “PROGRAM AE” or
“SHUTTER” in “FUNCTION” Menu. (੬ pg. 23)
● The selected effect will be shown for approx. 2
seconds before the camcorder returns to the
menu screen.
1 Set the Power Switch to “REC”.
2 Set the recording mode to “ ”. (੬ pg. 18)
3 Set “WIPE/FADER” in “FUNCTION” Menu.
NOTES:
(੬ pg. 23)
● Shutter Effects cannot be used during “NIGHT”.
● When a subject is too bright or reflective, a
vertical streak may appear (smear
phenomenon). Smear phenomenon tends to
occur when “SPORTS” or any mode of
“SHUTTER 1/500 – 1/4000” is selected.
4 Press the Recording Start/Stop Button to
activate the Fade-in/out or Wipe-in/out.
NOTE:
You can extend the length of a Wipe or Fader by
pressing and holding the Recording Start/Stop
Button.
PROGRAM AE
WIPE/FADER
OFF: Disables the function. (Factory-preset)
SPORTS
OFF: Disables the function. (Factory-preset)
(Variable Shutter Speed: 1/250 – 1/4000):
This setting allows fast-moving images to be
captured one frame at a time, for vivid, stable
slow-motion playback. The faster the shutter
speed, the darker the picture becomes. Use
the shutter function under good lighting
conditions.
WHITE
screen.
: Fade in or out with a white
: Fade in or out with a black
: Wipe in from right to left, or wipe
BLACK
screen.
SLIDE
out from left to right.
SNOW
: Compensates for subjects that
SCROLL
: The scene wipes in from the
may otherwise appear too dark when shooting
in extremely bright surroundings such as in the
snow.
bottom to the top of a black screen, or wipes
out from top to bottom, leaving a black screen.
SPOTLIGHT
: Compensates for subjects
that may otherwise appear too bright when
shooting under extremely strong direct lighting
such as spotlights.
TWILIGHT
: Makes evening scenes look
more natural. White Balance (੬ pg. 29) is
automatically set to “AUTO”. When Twilight is
chosen, the camcorder automatically adjusts
the focus from approx. 10 m (32 ft) to infinity.
From less than 10 m, adjust the focus
manually.
NIGHT
: Makes dark subjects or areas
even brighter than they would be under good
natural lighting. Although the recorded image
is not grainy, it may look as if it is strobing due
to the slow shutter speed.
During Night-Alive, it may be difficult to bring
the camcorder into focus. To prevent this, use
of a tripod is recommended.
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES FOR RECORDING
EDITING
EN
31
EFFECT
Dubbing To A VCR
To use this camcorder as a player
OFF: Disables the function. (Factory-preset)
SEPIA
: Recorded scenes have a brownish
tint like old photos.
1 Following the illustration, ੬ pg. 21,
MONOTONE
: Like classic black and white
“Connections To A TV Or VCR” , connect the
camcorder and the VCR’s input connectors.
films, your footage is shot in B/W.
CLASSIC
strobe effect.
STROBE
series of consecutive snapshots.
: Gives recorded scenes a
2 Perform steps 1 - 6 (੬ pg. 21)
3 At the point you want to start dubbing, start
recording on the VCR. (Refer to the VCR’s
instruction manual.)
:Your recording looks like a
MIRROR
: Creates a mirror image on the
4 To stop dubbing, stop recording on the
left half of the screen, juxtaposed to the normal
image on the other half.
VCR, then stop playback on the camcorder.
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
SHUTTER
OFF: Disables the function. (Factory-preset)
● To choose whether or not the following displays
appear on the connected TV
• Date/time
Set “DATE/TIME” to “ON” or “OFF”
(੬ pg. 25).
• Time code
Set “TIME CODE” to “OFF” or “ON”
(੬ pg. 25).
• Indications other than date/time and time code
Set “ON SCREEN” to “OFF”, “LCD” or “LCD/
TV” (੬ pg. 25).
SHUTTER 1/60: The shutter speed is
fixed at 1/60th of a second. Black bands that
usually appear when shooting a TV screen
become narrower.
SHUTTER 1/100: The shutter speed is
fixed at 1/100th of a second.The flickering that
occurs when shooting under a fluorescent light
or mercury-vapour lamp is reduced.
SHUTTER 1/500/SHUTTER 1/4000:
(Refer to PROGRAM AE - SPORTS
mode.)
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
32
NOTES:
Dubbing To Or From A Video Unit
Equipped With A DV Connector
(Digital Dubbing)
It is also possible to copy recorded scenes
from the camcorder onto another video unit
equipped with a DV connector. Since a digital
signal is sent, there is little, if any, image or
sound deterioration.
● It is recommended to use the AC Adapter as
the power supply instead of the battery
pack. (੬ pg. 13)
● If a blank portion or disturbed image is played
back on the player during dubbing, the dubbing
may stop so that an unusual image is not
dubbed.
● Even though the DV cable is connected
correctly, sometimes the image may not appear
in step 4. If this occurs, turn off the power and
make connections again.
● If SNAPSHOT is pressed during playback, only
the original playback image recorded on the
tape is output from the DV IN/OUT connector.
● When using a DV cable, be sure to use the
optional JVC VC-VDV204U or VC-VDV206U
DV cable.
To use this camcorder as a recorder
1 Make sure all units are turned off.
To DV IN/OUT
2 Connect this camcorder to a video unit
equipped with a DV output connector using a
DV cable as shown in the illustration.
3 Set the camcorder’s Power Switch to
“PLAY”.
4 Set “REC MODE” to “SP” or “LP”.
DV cable (optional)
To DV IN/OUT
Core filter
(੬ pg. 25)
5 Start playback on the player.
6 Press the Recording Start/Stop Button to
engage the Record-Pause mode.
• The “
” indication appears on the
DV IN
screen.
7 At the point you want to start dubbing, press
the Recording Start/Stop Button to start
Video unit equipped with DV connector
To use this camcorder as a player
1 Make sure all units are turned off.
dubbing. The
indication rotates.
8 Press the Recording Start/Stop Button
again to stop dubbing. The
stops rotating.
indication
2 Connect this camcorder to a video unit
equipped with a DV input connector using a DV
cable as shown in the illustration.
9 Press 7 to return to the normal playback
mode.
NOTE:
3 Start playback on the camcorder.
Digital Dubbing is performed in the sound mode
recorded on the original tape, regardless of the
current “SOUND MODE” setting. (੬ pg. 24)
(੬ pg. 19)
4 At the point you want to start dubbing, start
recording on the video unit. (Refer to the video
unit’s instruction manual.)
COPY PROTECTED
Appears if dubbing of copyguarded signals is
attempted while this camcorder is being used
as a recorder.
5 To stop dubbing, stop recording on the
video unit, then stop playback on this
camcorder.
Download from Www.Somanuals.com. All Manuals Search And Download.
EDITING
EN
33
It is also possible to transfer still/moving
Connection To A Personal
Computer
images to a PC with a DV connector by using
the provided software, software equipped with
the PC or commercially available software.
If you are using a Windows® XP, you can use
Windows® Messenger to conduct video
conferences over the Internet, using a
camcorder. For details, refer to the help for the
Windows® Messenger.
Using DV cable
NOTES:
● It is recommended to use the AC Adapter as
the power supply instead of the battery pack.
(੬ pg. 13)
● When using a DV cable, be sure to use the
optional JVC VC-VDV206U or VC-VDV204U
DV cable depending on the type of DV
connector (4 or 6 pins) on the PC.
● The date/time information cannot be captured
into the PC.
To DV IN/OUT
Core filter
● Refer to the instruction manuals of the PC and
Software.
● The still images can also be transferred to a PC
with a DV connector-equipped capture board.
● The system may not work properly depending
on the PC or capture board you are using.
● If, after connecting a DV cable to the camcoder
and it doesn’t work, restart the camcoder.
DV cable (optional)
Core filter
To DV connector
or
PC with DV connector
When connecting the camcorder to a PC
using a DV cable, make sure to follow the
procedure below. Connecting the cable
incorrectly may cause malfunctions to the
camcorder and/or the PC.
● Connect the DV cable first to the PC, and
then to the camcorder.
● Connect the DV cable (plugs) correctly
according to the shape of the DV connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
If, after following the steps in the chart below,
the problem still exists, please consult your
nearest JVC dealer.
34
The focus does not adjust automatically.
● Focus is set to the Manual mode.
➜Set Focus to the Auto mode. (੬ pg. 27)
● The lens is dirty or covered with condensation.
➜Clean the lens and check the focus again.
(੬ pg. 27)
No power is supplied.
● The power is not connected properly.
➜Connect the AC Adapter securely. (੬ pg. 12)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-
attach it firmly. (੬ pg. 13)
● The battery is dead.
➜Replace the dead battery with a fully charged
one. (੬ pg. 12)
The color of Snapshot looks strange.
● The light source or the subject does not include
white. Or there are various different light
sources behind the subject.
➜Find a white subject and compose your shot so
that it also appears in the frame. (੬ pg. 26, 29)
Recording cannot be performed.
The POWER/CHARGE lamp on the
camcorder does not light during charging.
● The tape’s erase protection tab is set to “SAVE”.
➜Set the tape’s erase protection tab to “REC”.
(੬ pg. 15)
● Charging is difficult in places subject to
extremely high/low temperatures.
➜To protect the battery, it is recommended to
charge it in places with a temperature of 10°C
to 35°C (50°F to 95°F). (੬ pg. 36)
● The battery pack is not attached firmly.
➜Detach the battery pack once again and re-
attach it firmly. (੬ pg. 12)
● “TAPE END” appears.
➜Replace with new cassette. (੬ pg. 15)
● The cassette holder cover is open.
➜Close the cassette holder cover.
When shooting a subject illuminated by
bright light, vertical lines appear.
This is not a malfunction.
The image looks like the shutter speeds is
too slow.
When the screen is under direct sunlight
during shooting, the screen becomes red
or black for an instant.
● When shooting in the dark, the unit becomes
highly sensitive to light when “GAIN UP” is set
to “AUTO”.
➜If you want the lighting to look more natural, set
“GAIN UP” to “AGC” or “OFF”. (੬ pg. 23)
This is not a malfunction.
The LCD monitor or viewfinder indications
blink.
● Effects function that cannot be used together
are selected at the same time.
➜Re-read the sections covering Effects.
(੬ pg. 23)
Images on the LCD monitor appear dark
or whitish.
● In places subject to low temperature, images
become dark due to the characteristics of the
LCD monitor. This is not a malfunction.
➜Adjust the brightness and angle of the LCD
monitor. (੬ pg. 8, 14)
● When the LCD monitor’s fluorescent light
reaches the end of its service life, images on
the LCD monitor become dark.
The tape is moving, but there is no
picture.
● Your TV has AV input terminals, but is not set to
its VIDEO mode.
➜Set the TV to the mode or channel appropriate
for video playback. (੬ pg. 21)
➜Consult your nearest JVC dealer.
● The cassette holder cover is open.
➜Close the cassette holder cover. (੬ pg. 15)
Blocks of noise appear during playback,
or there is no playback picture and the
screen becomes blue.
● Clean the video heads with an optional cleaning
cassette. (੬ pg. 5)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
EN
35
Picture does not appear on the LCD
monitor.
● The viewfinder is pulled out and “PRIORITY” is
set to “FINDER”.
➜Push the viewfinder back in or set “PRIORITY”
to “LCD”. (੬ pg. 8, 24)
UNIT IN SAFEGUARD MODE
REMOVE AND REATTACH BATTERY OR
DC PLUG
Error indications 01, 02 or 06.
Remedy: Remove and reattach the power supply
or battery.
● The LCD monitor’s brightness setting is too
dark.
➜Adjust the brightness of the LCD monitor.
(੬ pg. 14)
➜If the monitor is tilted upward 180 degrees,
open the monitor fully. (੬ pg. 8)
UNIT IN SAFEGUARD MODE
EJECT AND REINSERT TAPE
Error indications 03 or 04.
Remedy: Eject the cassette and reinsert.
In the above 2 error indications, the camcorder
turns off automatically. Eject the cassette once
and re-insert it, then check if the indication clears.
When it does, you can resume using the
camcorder. If the indication remains, consult your
nearest JVC dealer.
Aspect ratio is strange
If the aspect ratio of the video you are playing is
strange, change the setting in “16:9 OUTPUT”.
(੬ pg. 24, 25)
Displays the battery remaining power.
Remaining power level
High
Exhausted
As the battery power comes close to nil, the
battery remaining power indicator blinks.
When the battery power is exhausted, power turns
off automatically.
TAPE END
Appears when the tape ends during recording or
playback.
LENS CAP
Appears for 5 seconds after power is turned on if
the lens cap is attached or when it is dark.
SET DATE/TIME!
● Appears when the date/time is not set.
(੬ pg. 14).
● The built-in clock battery has run out and the
previously set date/time has been erased.
➜Consult your nearest JVC dealer for
replacement.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
EN
36
AC Adapter
The Benefits Of Lithium-Ion Batteries
Lithium-ion battery packs are small but have
a large power capacity. However, when one is
exposed to cold temperatures (below 10°C/
50°F), its usage time becomes shorter and it
may cease to function. If this happens, place
the battery pack in your pocket or other
warm, protected place for a short time, then
re-attach it to the camcorder.
When using the AC Adapter in areas other
than the USA
The provided AC Adapter features automatic
voltage selection in the AC range from 110V to
240 V.
USING HOUSEHOLD AC PLUG ADAPTER
In case of connecting the unit’s power cord to an
AC wall outlet other than American National
Standard C73 series type use an AC plug
adapter, called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest
JVC dealer.
NOTES:
● It is normal for the battery pack to be warm after
charging, or after use.
Temperature Range Specifications
Charging: 10°C to 35°C (50°F to 95°F)
Operation: 0°C to 40°C (32°F to 104°F)
Storage: –20°C to 50°C (–4°F to 122°F)
● The lower the temperature, the longer
recharging takes.
Plug adapter
● Charging times are for a fully discharged battery
pack.
Battery Packs
The supplied battery pack is
a lithium-ion battery. Before
using the supplied battery
pack or an optional battery
pack, be sure to read the
following cautions:
● To avoid hazards
...do not burn.
...do not short-circuit the terminals. When
transporting, make sure the provided battery
cap is attached to the battery. If the battery cap
is misplaced, carry the battery in a plastic bag.
...do not modify or disassemble.
...do not expose the battery to temperatures
exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
...use only specified chargers.
Terminals
Cassettes
To properly use and store your cassettes, be
sure to read the following cautions:
● During use
...make sure the cassette bears the Mini DV
mark.
...be aware that recording onto prerecorded
tapes automatically erases the previously
recorded video and audio signals.
...make sure the cassette is positioned properly
when inserting.
...do not load and unload the cassette repeatedly
without allowing the tape to run at all. This
slackens the tape and can result in damage.
...do not open the front tape cover. This exposes
the tape to fingerprints and dust.
● Store cassettes
...away from heaters or other heat sources.
...out of direct sunlight.
...where they won’t be subject to unnecessary
shock or vibration.
...where they won’t be exposed to strong
magnetic fields (such as those generated by
motors, transformers or magnets).
...vertically, in their original cases.
● To prevent damage and prolong service
life
...do not subject to unnecessary shock.
...charge in an environment where temperatures
are within the tolerances shown in the chart
below. This is a chemical reaction type
battery — cooler temperatures impede
chemical reaction, while warmer temperatures
can prevent complete charging.
...store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.
...fully charge and then fully discharge the battery
every 6 months when storing the battery pack
over a long period time.
...remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
...keep the lens directed at extremely bright
objects for long periods.
EN
37
LCD Monitor
● To prevent damage to the LCD monitor,
DO NOT
...push it strongly or apply any shocks.
...place the camcorder with the LCD monitor on
the bottom.
...expose the lens and viewfinder’s lens to direct
sunlight.
...carry it by holding the LCD monitor or the
viewfinder.
...swing it excessively when using the hand strap
or the grip.
...swing the soft camera case excessively when
the camcorder is inside it.
● To prolong service life
...avoid rubbing it with coarse cloth.
● Be aware of the following phenomena for
LCD monitor use.These are not
malfunctions
● Dirty heads can cause the following
problems:
...While using the camcorder, the surface around
the LCD monitor and/or the back of the LCD
monitor may heat up.
...If you leave power on for a long time, the
surface around the LCD monitor becomes hot.
...No picture during playback.
Main Unit
● For safety, DO NOT
...Blocks of noise appear during playback.
...During recording or playback, the Head Clog
Warning indicator “ ” appears.
...open the camcorder’s chassis.
...disassemble or modify the unit.
...short-circuit the terminals of the battery pack.
Keep it away from metallic objects when not in
use.
...allow inflammables, water or metallic objects to
enter the unit.
...remove the battery pack or disconnect the
power supply while the power is on.
...leave the battery pack attached when the
camcorder is not in use.
...Recording cannot be performed properly.
In such cases, use an optional cleaning
cassette. Insert it and play back. If the cassette
is used more than once consecutively, damage
to the video heads may result. After the
camcorder plays back for about 20 seconds, it
stops automatically. Also refer to the cleaning
cassette’s instructions.
If, after using the cleaning cassette, the
problems still exist, consult your nearest JVC
dealer.
Mechanical moving parts used to move the
video heads and video tape tend to become
dirty and worn out over time. In order to
maintain a clear picture at all times, periodic
check-ups are recommended after using the
unit for about 1,000 hours. For periodic check-
ups please consult your nearest JVC dealer.
● Avoid using the unit
...in places subject to excessive humidity or dust.
...in places subject to soot or steam such as near
a cooking stove.
...in places subject to excessive shock or
vibration.
...near a television set.
...near appliances generating strong magnetic or
electric fields (speakers, broadcasting
antennas, etc.).
...in places subject to extremely high (over 40°C
or 104°F) or extremely low (under 0°C or 32°F)
temperatures.
● DO NOT leave the unit
...in places of over 50°C (122°F).
...in places where humidity is extremely low
(below 35%) or extremely high (above 80%).
...in direct sunlight.
...in a closed car in summer.
...near a heater.
● To protect the unit, DO NOT
...allow it to become wet.
...drop the unit or strike it against hard objects.
...subject it to shock or excessive vibration during
transportation.
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIONS
EN
38
About moisture condensation
Changes or modifications not approved by
JVC could void the user’s authority to operate
the equipment. This equipment has been
tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses,
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
● You have observed that pouring a cold liquid
into a glass will cause drops of water to form
on the glass’ outer surface. This same
phenomenon occurs on the head drum of a
camcorder when it is moved from a cool place
to a warm place, after heating a cold room,
under extremely humid conditions or in a place
directly subjected to the cool air from an air
conditioner.
● Moisture on the head drum can cause severe
damage to the video tape, and can lead to
internal damage to the camcorder itself.
interference to radio communications.
However, there is no guarantee that
CONDENSATION, OPERATION
PAUSED PLEASE WAIT
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Appears if condensation occurs. When this
indication is displayed, wait more than 1
hour until condensation disappears.
Serious malfunctioning
If malfunctioning occurs, stop using the unit
immediately and consult your local JVC
dealer.
The camcorder is a microcomputer-controlled
device. External noise and interference (from
a TV, a radio, etc.) might prevent it from
functioning properly. In such cases, first
disconnect its power supply unit (battery
pack, AC Adapter, etc.) and wait a few
minutes and then re-connect it and proceed
as usual from the beginning.
Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est
conforme à la norme NMB-003 du Canada.
Declaration of Conformity
Model Number
Trade Name
: GR-D750U
: JVC
Responsible party : JVC AMERICAS
CORP.
Address
: 1700 Valley Road
Wayne, N. J. 07470
Telephone Number : 973-317–5000
This device complies with Part 15 of FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
EN
39
Camcorder
For Digital Video Camera
Format
For General
Power supply
DC 11 V (Using AC Adapter)
DC 7.2 V (Using battery pack)
Power consumption
Approx. 2.2 W (2.3 W*) (LCD monitor off,
viewfinder on)
Approx. 2.7 W (2.8 W*) (LCD monitor on,
viewfinder off)
DV format (SD mode)
Signal format
NTSC standard
Recording/Playback format
Video: Digital component recording
Audio: PCM digital recording, 32 kHz 4-channel
(12-BIT), 48 kHz 2-channel (16-BIT)
Cassette
Mini DV cassette
Tape speed
SP: 18.8 mm/s, LP: 12.5 mm/s
Maximum recording time (using 80 min.
cassette)
Approx. 7.5 W (Maximum; when charging the
battery pack)
*
Using LED Light
Dimensions (W x H x D)
61 mm x 94 mm x 114 mm (2-3/8" x 3-11/16" x
4-1/2") (with the LCD monitor closed and the
viewfinder pushed back in)
Weight
SP: 80 min., LP: 120 min.
For Connectors
AV
Video output: 1.0 V (p-p), 75 Ω, analog
Audio output: 300 mV (rms), 1 kΩ, analog, stereo
DV
Approx. 410 g (0.90 lbs) (without battery, cassette
and lens cap)
Approx. 480 g (1.06 lbs) (incl. battery, cassette
and lens cap)
Input/output: 4-pin, IEEE1394 compliant
Operating temperature
0°C to 40°C (32°F to 104°F)
Operating humidity
35% to 80%
Storage temperature
–20°C to 50°C (–4°F to 122°F)
Pickup
AC Adapter
Power requirement
AC 110 V to 240 V~, 50 Hz/60 Hz
Output
DC 11 V =, 1 A
1/6" CCD
Lens
Specifications shown are for SP mode unless
otherwise indicated. E & O.E. Design and
specifications subject to change without notice.
F 2.0, f = 2.3 mm to 78.2 mm, 34:1 power zoom
lens
Filter diameter
ø27 mm
LCD monitor
2.7" diagonally measured, LCD panel/TFT active
matrix system
Viewfinder
Electronic viewfinder with 0.33" color LCD
Speaker
Monaural
LED Light
Effective distance: 1.5 m (5 ft)
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS
EN
A
L
T
AC Adapter ....................13 Language ...................... 24 Tape Speed (REC MODE)
Auto/Manual Mode ........18 LCD Monitor and Viewfinder
...........................24, 25
................................ 14 Tele Macro .....................23
LED Light ...................... 26 Telephoto Setting ..........23
Loading A Cassette ....... 15 Time Code ...............18, 24
B
Backlight Compensation 28
Battery Pack ......12, 13, 36
Blank Search .................20
Tripod Mounting .............14
Troubleshooting .............34
M
Bright .......................24, 25 Manual Focus ............... 27
W
Melody .......................... 24
C
Motor Drive Mode .......... 26 White Balance ...............29
Cam Reset .....................25
Changing The Menu
Wind Cut ........................23
Wipe Or Fader Effects ...30
N
Settings ...........22 – 25 Narration ....................... 25
Z
Charging The Battery Pack
.................................12
Clock Adj. ..........14, 24, 25
Connection To A Personal
Computer ................33
Connections To A TV Or
VCR ........................21
Control Level ...................7
Night Alive ..................... 30
Zooming ...................17, 23
O
On Screen ............... 24, 25
16:9 Output ..............24, 25
P
Playback Sound ............ 25
Power-linked operation ... 8
Priority ........................... 24
Program AE .................. 30
D
Data Battery ...................13
Date/Time Settings ........14
Demonstration Mode .....24
Digital Image Stabilization
(DIS) .......................23
Q
Quick Review ................ 16
R
Rec Mode ................ 24, 25
Recording Capacity
Dubbing ...................31, 32
Tape ....................... 16
E
Effect .............................31
Exposure Control ...........27
S
Shutter Effects ........ 30, 31
Snapshot Mode ............. 26
Sound L/R ..................... 25
Sound Mode .................. 24
Speaker Volume ........... 19
Specifications ................ 39
Spot Exposure Control .. 28
G
Gain Up .........................23
I
Interface Shooting .........17
Iris Lock .........................28
J
Journalistic Shooting .....17
Printed in Malaysia
US
© 2006 Victor Company of Japan, Limited
1206ASR-NF-MP
Download from Www.Somanuals.com. All Manuals Search And Download.
|